Professional Documents
Culture Documents
SIGMA Wide - Quick Installation Guide (293732930-G)
SIGMA Wide - Quick Installation Guide (293732930-G)
deviation at +25ºC (roughly +/- 3sec per day). At lower and higher temperature, Tel: +91 8929 159 665 WEEE
➢ Do not install the terminal in the vicinity of gas stations or any other installation Guides
containing flammable or combustible gases or materials. The terminal is not deviation may be greater (maximum : 8sec per day).
designed to be intrinsically safe. • When the terminal is used for applications requiring high time precision, it is India
strongly recommended to synchronize the terminal with an external clock.
293732930-G
Mail: support.bioterminals.in@idemia.com For further installation guidance refer to installation
manual part number 2014_0000000606
The terminal should be installed in controlled lighting conditions
➢ Avoid biometric sensor exposure to a blinking light. Firmware release Tel: +91 1800 120 203 020
➢ Avoid direct exposure of the biometric sensor to sunlight or to UV lights. • To get the best of our technology, we recommend you to download and install
the last firmware release. Please check our website. Detailed instructions are available at
Outdoor installations recommendations Des instructions détaillées sont disponibles sur 1
➢ Outdoor devices shall not encounter extreme weather such as torrential rains, Overvoltage El detalle de las instrucciones está disponible en
harvest rains, flooding. • IDEMIA recommends the Biometric devices to be protected with an external
➢ High humidity, direct sun exposure, frequent high temperature, outdoor careless accessory in order to avoid overvoltage on input wires or connectors of the
device. Typically, risks of overvoltage have been identified on external power
https://biometricdevices.idemia.com
uses may alter the durability of the terminal.
➢ When the terminal is exposed to such potential extreme conditions, IDEMIA management wire, POE connector and wiegand input wire.
recommends deploying an enclosure to protect the terminal and thus ensure a
long-lasting performance in the field. WARNING: Cleaning & Disinfection precautions
!
To clean the terminal, a dry cloth is recommended, especially the biometric
sensor.
USB
! the installation.
POE Before proceeding, make sure that the person in charge of installation and
connections, is properly connected to earth, in order to prevent Electrostatic
Discharges (ESD).
External Power supply: 12/24 VDC (regulated and filtered) 1A min @12VDC or
µSD 500mA min @24VDC, IEC 60950-1 standard compliant. A 12 Volts power supply
compliant with SIA's Wiegand standard will also be suitable. If sharing power between
devices, each unit must receive 1A (e.g. two units would require a 12 VDC, 2A supply).
For UL compliance the units shall be powered via a class 2 output from a UL 294
power supply.
A battery backup or uninterrupted power supply (UPS) with built-in surge protection is
recommended.
25 WIEGAND_LEDOUT1 Blue Power Over Ethernet (POE): power can be provided through RJ-45 connector using a
26 WIEGAND_LEDOUT2 Blue / Red PSE (Power Sourcing Equipment) IEEE802.3af or IEEE802.3at type 1 compliant.
23 WIEGAND_IN1 White / Red
24 WIEGAND_OUT0 Green For UL compliance the units shall be powered via a UL 294B PSE power supply listed as
21 WIEGAND_OUT1 White a limited Power Source Unit. The PSE shall be rated min of 41-57VDC (-10% / +15%),
22 WIEGAND_IN0 Green / Red 1Amp.
20 WIEGAND_GND Black / Red
The terminal is a Class 0 (15.4 W) PD (Powered Device).
19 RS422/485_GND Black / Red Warning: after use, the temperature of the POE module may be high: after power
3 4 17 RS422_RX_A Blue / Black cut off, wait 5mn before working on connectors area.
18 RS422_TX_Z/RS485_Z Green / White
! 15
16
RS422_RX_B
RS422_TX_Y/RS485_Y
Blue / White
Green / Black
IDEMIA recommends using a Gauge AWG20 for 12V power supply.
The voltage measured on the product block connector of the terminal must be equal to
7 RLY_NC Orange / White 12V-24V (-15% / +10%).
5 RLY_NO Yellow / White The voltage drop due to the cable shall be taken into account. The table below shows
6 RLY_COM Grey / White
3 SWITCH_PIN1 Light Blue
the maximum voltage drop between the power source and the terminal, depending on
Relay output 30VDC, 2A.
4 SWITCH_PIN2 Pink the length of the cable.
Suitable for inductive and resistive 1 Power +12V Red
loads. Inductive load management 2 Power GND Black
requires a parallel diode for a better
Gauge Diameter Maximum drop voltage (V)
! contact lifetime.
Tamper 30VDC, 100 mA (Resistive).
13
14
11
GPI2
GPO2
GPI1
Orange / Black
Yellow / Black
Orange / Red
AWG (mm)
at 1m at 5m at 10m
12 GPO1 Yellow / Red 20 0.81 0.03 0.17 0.33
UL has not verified Wi-Fi Capabilities. 9 GPI0 Orange
10 GPO0 Yellow 22 0.64 0.05 0.26 0.53
Ethernet connection is for supplemental 8 GPIO_GND Black / Red 24 0.51 0.08 0.42 0.84
2 use not UL evaluated.
The input circuits are not evaluated for UL burglar alarm use
For UL installations only Wiegand is to be used. WARNING: Under powering may cause memory and data corruption; over
UL has not evaluated GPIO and RS422/485 communication. ! powering may cause hardware damage. Both of these situations will void
1 For UL 294 installation, length of communication (RS422-RS485/Wiegand) and I/Os the warranty.
(GPI/GPO) cables must not exceed 30 meters (98.4 feet).
5 6 7
(POE)
2
1
(WR)