Professional Documents
Culture Documents
Graco
Graco
~~
RATIO
l!l
The carbon steel pumps above handle noncorrosive The carbon steel pumps above handle non-corrosive
fluids; tha stainlass steel pump handles corrosive6. They fluids; the stainless steel pump handle6 corrosives. They
are UL listed for light Viscosity paints, lacquers, var- are UL listed for light viscositf .pints, lacquers, var-
nishes, thinners. solvents when installed in accordance nishes. thinners, solvents when installed in accordan=
30.
with NFPA (National Fire Protection Associationl Stan- with NFPA (National Fire Protection Association) Stan-
dards No. 3 0, Flammable and Combustible Liquids Code, dards No. Flammable and Combustible Liquids Cpde.
and No. 33 Spray Finishing Using Rammabla Materials. and No. 33 Spray Fimshlng Using Flammable Matenals.
2269
-49. Rubber Packed
Carbon Steel,
Series A
21am
Rubber Packed Series A
Et 17
27
Et 28
226-950" Carbon Steel, 218-116 27
Rubber Packed Series A Et 28
Pump Models226-948 and 226-952 handle noncorrosiva 226-951'" Carbon Steel. 218116 27
light viscosih, fluids, such as anti-freaze, windshield Rubber Packed Series A Et 28
washer solvent, ATF. motor oil and hydraulic oil.
226-953 Stainless Steel, 220-440 14
Rubber Packed Series A Et 19
~~ ~~ ~~~~ ~~~~ ~ ~~
FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS.
Read and understand all instruction manuals before operating equipment.
EQUIPMENT MISUSE HAZARD
Ge nera l S af et y Fluid Compatibility
Any misuse of the equipment or accessories, such es over- BE SURE that all fluids and solvents used erechemically com-
pressurizing, modifying parts, using incompatible chemicals patible with the wettedparts shown in theTechnical Data on
and fluids,or using worn or damaged parts, can cause them to the back cover. Always read the fluid and solvent manufac-
rupture and result in serious bodily injury, such as splashing turer's literature beforeusing them in this pump.
fluid in theeyes or on the skin, fire, explosion, or propew
damage. Pressure Relief Procedure
To reduce the risk of serious bodily injury, including splashing
NEVER alter or modify any part of thisequipment; doing so in theeyes or on the skin, or injury from moving parts, always
could cause it to malfunction. follow this procedure whenever you shut off the pump, when
checking or servicing any part of the system. when installing,
CHECK all equipment regularly and repair or replace worn or cleaning or changing nozzles, and wheneveryou stopdispens-
damaged parts immediately. Ing.
ALWAYS read and follow the fluid and solvent 1. Shut off the air to the pump.
manufacturer's literature regarding the use of protective 2. Close the bleed-type master air valve (required in your
clothing andequipment. system).
3. Hold a metal partof the dispensing valvefirmly to the side
System Pressure of a grounded metal pail, and actuate the valve to relieve
This pump can develop 16 bar (230 psi/ MAXIMUMWORK- pressure.
ING PRESSURE. at 12.4 bar (180 psi) MAXIMUM INCOM- 4. Open the drain valve (required i?your system), having a
ING AIR PRESSURE. Be sure that all equipment and ac- container ready to catch the dramage.
cessories are rated to withstand the maximum working 5. Leave the drain valve open until youare ready to dispense
pressure of thispump. DO NOT exceedthe maximum working again.
pressure of any component or accessory used in thesystem.
If you suspect that thenozzle or hose is completely clogged,
or thatpressure hasnot been fully relievedafter following the
steps above, VERY SLOWLY loosen the hose end coupling
and relieve pressure gradually,then loosen completely. Now
clear the nozzle or hose.
2 ,30747
~
TYPICAL INSTALLATION
-..I@ Adapter
Air Line Lubriiator
D Bleed-Type Master Air Valve
H Fluid Outlet
J Pin Fitting
K Air Control Valve (All Models
except 226-949.226-950. and
L
2289511
Air Line Coupler M
M Grounded FluidHose
CC Air Regulator Kit (Models226949,
228950. and 226-951 only)
12 mm I O . V
rn
I ~ /
7
INSTALLATION
The Typical Installation shownabove is only a guide. System Accessories
Contact your Graco representative for assistance in Refer to the Typical Installation drawing and to AC-
designing a systemto meet your needs. CESSORIES on pages 29 and 30.
NOTE: Reference numbers and letters in the text NOTE: To ensure maximum pump performance, be
refer to the Typical Installation, Figs 1-9, and sure that all accessories used are properly
to the Parts Lists on pages 13-28. sized to meet your system requirements.
Mount the pumpto suit the typeof installation planned. Most models are supplied with a needle-type air control
Graco mounting accessories are shown in the AC- valve (K) at the pump air inlet. Models 226-949.226-950.
CESSORIES section on pages 29 and 30.
With 55 gallon and 226-951 are equipped with an air regulator kit K C )
instead. All models are supplied with an air line quick
drum length pumps (except Models 226-949 and
226-950). screw the bung adapter ( 8 ) tightly into the disconnect coupler (L) toconnect the air line to the
bung hole of the drum and adjust to hold the pump pump and accessories.
12 mm (0.5 in.)off the bottom of the drum. Loosen the
vent plug (A) toprevent formationof a vacuum in the The following paragraphs describe the orderof installa-
drum. With Models 226-949 and 226-950 pumps, follow tion of air line accessories and supplied components.
the instructions on page 4 under Valve Kit Installation Contact your Graco representative for assistance in
before installing the pumpin the drum of tank. Stubby designing your system.
pumps maybe mountedon thewall or to the side of the
drum with a clamp. See ACCESSORIES. WARNING
Required in your system area bleed-type master
NOTE: Dimensions, air inlet andfluid outlet sizes are air valve ID) and a fluid drain valve (GI. These ac-
given in the TECHNICAL DATA on the back cessories help reducethe risk of serious bodily in-
cover. jury including splashingin the eyes or onthe skin,
and injury from moving partsif you are adjusting
If low level cut-off valve 210-865(see ACCESSORIES) is or repairing the pump.
being used, install a drum-length pump (except Models
226-949, 226-950and 226-9511 in the container with the The b/eed-type masterair valve relieves air trap-
intake valve 210-865 resting on the containerbottom. ped between this valve and the pump after the
This accessory valvewill not fitpumps with e telescop- pump is shut off. Trapped air can causethe pump
ing suction tube. to cycle unexpectedly and resultin serious bodily
injury, including amputation.
CAUTION
The fluid drain valve helps relieve pressurein the
strap wrenchto avoid damaging the valve.Do not displacement pump, hose, and dispensing valve
use the legs of the valve to tighten it into the when shutting off the pump. Actuating the
dispensing valve to relieve pressure may not be
sufficient, especially if there is a clog in the hose
or the dispensing valve.
307-427 3
For automatic air motor lubrication, install an air line
lubricator (C) downstream from the air regulator (if sup-
plied) and all other accessories. Install a bleed-type
master air valve( D ) close to the pump. Next, install the
air regulator (CCI, if supplied. Installan air linefilter (E)
upstream from all other accessories, to remove harmful
dirt and moisture from the compressed air supply.
Using a suitable adapter, install the male disconnect pin
fitting (J)in the air filter inlet. Install theair line quick
disconnect coupler (L) on the air hose(F), but do not
connect it to the pin fitting yet.
Connect a grounded fluid hose (M)to the 314 npt(f)
fluid outlet.
Valve Kit Installation (Models226-949 and 226-950
only)
Using 'thread sealer on the male threads of the street
elbow (AA), screw it into the pumpfluid outlet (HI until
tight and the dispensing valve (BB) is in the position
shown in Fig 2.
Using moderate force only, extend the pump suction
tube, insert thepump into the drum or tank bung hole, MODEL
and screw the bung adapter (B) tightly into the bung
hole. Lift the pump about12 mm (0.5 in.) and tighten SHOWN
1-
the bung adapter (6) screw to hold the pump. Loosen
the vent plug (A). Refer to Typical Installation onpage
3.
1-CAUTIO
To N
prevent damaging the O-ring seals inside the Fig 2
4 307-427
WARNING Slowly open air valve (K) or regulator (CC) until pump
Pressure Relief Procedure cycles 5 to 20 cycleslmin. The pump itself only takes a
To reduce the risk of serious bodily injury, in- few strokes to prime. In a large system, however, the
cluding splashingin the eyes or on the skin, or in- pump may haveto be cycled for several minutes to fillall
jury from moving parts, always follow this pro- of the lines. Once the pump and system is primed, use
cedure whenever you shut off the pump, when the air valve orregulator to control pump speed andcy-
checking or servicingany part of the system, when cle rate: always usethe lowest pressure needed to get
installing, cleaning or changing nozzles, and the desired result.
whenever you stop dispensing.
On Models 226-949.226-950 or 226-951 (or other models
1. Shut off the air to the pump. using an accessory dispensing valve), pump will start
2. Close the bleed-type master air valve (required and stop as the dispensing valveIS opened and closed.
in your system).
3. Hold a metalpart of the dispensing valvefirmly When used for transfer and supply operationswith no
to the side of a grounded metal pail, and ac- dispensing valve, pump will run whenever air is sup-
tuate the valve to relieve pressure. plied.
4. Open the drain valve (requiredin your system),
having a container readyto catch the drainage.
5. Leave the drain valve open until you are ready
to dispense again.
If you suspect that the nozzle or hose is completely
clogged, or that pressure hasnot been fully reliev-
ed after following the steps above, VERY SLOW-
LY loosen the hose end coupling and relieve
pressure gradually, then loosen completely. Now
clear the nozzle or hose.
MAINTENANCE
Fill the wet-cup (P) 112 full of Graco Throat Seal Liquid Never allow the pump to run dry offluid being pumped.
(TSL) or compatible solvent and keep it 112 full to keep A dry pump will quickly accelerate to a high speed;
fluid from drying on the displacement rod and damaging possibly damaging itself. If your pump accelerates
pump throat packings. See Fig 3. quickly, or is running too fast, stop it immediately and
check the fluid supply. If the supply containeris empty
Lubricate the throat packings frequently when you are and air has been pumpedinto lines, prime pump and
pumping a non-lubricating fluid, orare shutting down lines with fluid, or flush and leave filled with compatible
for more than a few days. Some pumps have a grease solvent. Be sure to eliminate all air from fluid system.
fitting (DD) for this purpose. See Fig 3.
To shut down, disconnect
the air line coupler(L). Follow
The accessory air line lubricator(C) shown on page 30 the Pressure Relief Procedure Warning above
provides automatic air motor lubrication. Install the whenever you stop pumping.
lubricator downstream from all other accessories. To
manually lubricatethe motor, disconnect the air lineat Periodically, checkthe tightness ofthe packing nut (P).
the air motor inlet, put about 15 drops of lightweight oil Nut should be tight enough to prevent leakage: no
in the inlet, reconnectthe air line andturn on the air to tighter. See Fig 3.
blow oil into themotor.
307427 6
~~
~
~~
TROUBLESHOOTING GUIDE
6 307427'
Before You Start
1. When replacing the packings, replace the glands
also. Lubricate the packings before installing them.
307-427 7
Throat Packing8
Remove the cylinder (€E) and piston as explained NOTE: On displacement pumps 215-953 end
previously. Remove the packing nut (P) and pull the 215-956, install the N o leather v-packings
displacement rod (R) out the top of the outlet housing below the singlePTFE v-packing.
(0). Inspect the outer surfaceof the displacement rod
for scoring or wear by runninga finger over the surface Leave the packing nut (P) loose until the displacement
or holding it up to the light at an angle. rod (R) has been installed.
NOTE: There aretwo throat packing configurations, CAUTION
depending on the displacement pump model. Insert displacement rodfrom the top of the outlet
Both configurations are covered in the housing to prevent sheering of packings.
following text, and are pictured in Figs 6-9.
Remove the throat peckings from the outlet housing Tighten the packing nut just enoughto prevent leaking.
(0). One configuration consistsof a female gland (U), Overtightening candamage the peckings.
three v-packings (V), and e male gland (W). The other
configuration includes a bearing (MM), u-cup packing Reconnect the displacement pump to the air motor.
(NN), O-ring (PP), and washer (RR). Reconnect the groundwireif it was disconnected during
service.
Clean and inspect all the parts for wear or damage.
Lubricate the packings before reassembly. Install the
parts one ata time, in the same positions as before. The
lips of the v-packingsor u-cup packing must face down
against fluid pressure!
.. -
228849.
MODELS
mmo
and P g S 1
ONLY
L-l"- I I' 8 I
31 N m (PIt-lbl
Displacement Pumps 215-955 and 220-440
(Used with Models 226-942 and 226-953)
LIPS OF
PACKING8
MUST FACE
DOWN
TORQUE TO
33 N'm 124 ft-lbl
LL
LIPS MUST
FACE UP
EE
66 N m 147 ft-lbl
10 30747
.
Displacement Pumps 215955,215957 and 218-114
(Used with Models 226-943, 226-944 and 226-948)
, .:
.... ,..
. . ..
TORQUE TO
31 N‘m I 2 3 ft-lbl
307427 11
Displacement Pumps 215-958 and 220-439
(Used with Models 226-945 and 226-952)
I
BUNG MOUNTDRUM-LENGTH PUMPS
CARBON STEEL MODELS QTY
REF PART DESCRIPTION
Model.226-940, leather packed NO. NO.
228-941, polyethylene packed
226-947. rubber packed 2 215960 MOUNTING KIT for Carbon Steel
Includes items 2-17. Pumps
Includes items 3-13, 16, 17 1
3 106541 .NUT, lock, ME, w h y l o n insert 3
4 178-923 .PIN, headed, straight 1
5 '180-166 .PIN, clip 1
6 177-171 .TIE ROO 3
7 169-963 .. .. . ...-, air
.FITTING. -. . line 1
*51 E 206-264 .NEEOLE VALVE ASSY.
.....
r
208538 .COUPLER, air line 1
215953 DISPL. PUMP
l3 (for 2 26940.See page 151 1
215954 - .- . . .PUMP
DISP. -....
(For 226-941, See page 16) 1
218-113 DISPL. PUMP
(for 226947, See page 17) 1
15 215963 AIR MOTOR, @e instruction manual
307-456 1
16 166-532 NUT, packing 1
17 164-698 KNOB, adjusting 1
307 numbers in descriptions refer to separate instructiofi
manuals.
c
10 165-722 ..BODY 1
11 166-531 ..RING, friction washer 1
12 166-529 ..NEEDLE 1
13 208-536 .COUPLER, air line 1
15-955 DISPLACEMENT PUMP
(For model 226.942. see page 18) 1
720-140 DISPLACEMENT PUMP
l4 (For model 226953. see page 19) 1
15 215-963 AIR MOTOR, see instruction manual
307-456 1
16 166-532 NUT, packing 1
17 164-698 KNOB, adjusting 1
307 numbers in descriptions refers to separate instruction
manuals.
5
6
7
8
13
307427 15
CARBON STEEL DISPLACEMENT PUMP
(for pump Model 226-9411
Model 215954 55 gallon size, polyethylene packed.
Series D
I
I
I
3 **
I TORQUE TO
33 N'm I24 ft-lbl
1
0-"4
218-112 REPAIR KIT 9
For Displacement Pump218-113
(Must be purchased separately)
LIPS MUST
REF NO. QTY FACE UP
3 2
4 1
5 1
6 1
16 1
17 1
307427 17
STAINLESS STEEL DISPLACEMENT PUMP
(for pump Model 226-9421
Model 216-955 55 gallon drum size, polyethylene packed.
Series B
f
i
i
26
-21
LIPS MUST
FACE DOWN
5
TORQUE TO
33 N'm (24 ft-lbl
TOROUE TO
33 N'm 124 ft-lbl
18 307-427
DRUM LENGTH, STAINLESS STEEL
DISPLACEMENT PUMP
(for pump Model 228953)
Model po-440 55 gallon drum sue, rubber packed
Series A 19
26
TORQUE TO
33 N'm 124 ft-lbl
33 N'm I 2 4 ft-lbl
301-427 19
STUBBY-LENGTH PUMPS
CARBON STEEL MODELS REF PART DESCRIPTION QN
Model 226-943,leather packed NO. NO.
228.944. polyethylene packed
228-948. rubber packed 2 215-960 MOUNTING KIT for Carbon Steel
Pumps
Include items 2-17.
Includes items 3-13, 16, 17
3 1w-541 . NUT, lock; M8, wlnylon insert
d 17am . PIN, headed, straight
5 *180-166 . 1
.. PIN, clip
6 177-171 TIE ROD
7 169-969 FITTING, air line
8 206-264 . NEEDLE VALVE ASSY.
Includes items 9-12, 16, 17
9
10
'157628
165-722 ..BODY
-
..PACKING. o-rina. nitrile rubber
DISPL. PUMP
See page 2 3 )
(for 2 26948, Sea page 24!
AIR MOTOR, ~ s lnstructlon
~ e manual
30743
."."
16 166532 NUT, packing
17 164-698 KNOB, adjusting
307 numbers in descriptions refer to separate instruction
manuals.
20 307-427
STUBBY LENGTH PUMPS
STAINLESS STEEL MODELS REF PART DESCRIPTION QTY
NO. NO.
226-96polyethylene packed.
Includes items 2-17. 2 215961 MOUNTING KIT for Stainless Steel
Pumps
226-952 rubber packed Includes items 3-13, 16, 17 1
Includes items 2-17. 3 104-541 .NUT, lock: M8. wlnylon insert 3
4 170-923 .PIN. headed, straight 1
5 *180-166 .PIN. clip 1
6 177-170 .TIE ROD 3
.FI'lTlNG, air line 1
.NEEDLE VALVE ASSY.
Includes items 9-12, 16, 17 1
." - ..PACKING, O-ring, nitrile rubber 1
10 lM722 ..BODY 1
11 166.531 ..RING, friction washer 1
12 166.529 ..NEEDLE 1
13 208-536 .COUPLER, air line 1
p15-m DISPLACEMENT PUMP
(For model 226-945.see page 25) 1
DISPLACEMENT PUMP
(For model 226-952.see page 26) 1
15 215-963 AIR MOTOR, see instruction manual
307-456 1
16 166.532 NUT, packing 1
17 164-698 KNOB, adjusting 1
307 numbers in descriptions refer to separate instruction
manuals.
Wecommended "tool box" spare parts. Keep on handto
reduce down time.
Refer to "How To Order ReplacementParts" on page 31.
3l N'm I 2 3 ft-lbl
LIPS MUST
i
p 33 N'm I 2 TO
TOROUE 4 ft-lb)
FACE DOWN
'"5 \
-16
-10
7m
1
W
I
1
4
9 iI LIPS MUS1
FACE UP
8
TOROUE TO
31 N'm I23 ft-lb)
REF NO.
-
12
QN
1
'J 1
14 3
LIPS MUST
FACE DOWN
i LIPS MUST
FACE UP
11
TORDUE TO
w
215-964 REPAIR KIT
For Displacement Pump215-958
(Must be purchased separately)
REF NO. an
6 1
7 1
1
19
l8 3
301-421 25
STUBBY LENGTH, STAINLESSSTEEL
DISPLACEMENT PUMP
Ifor pump Model 226-952)
Model po-439 Stubby Size, rubber packed.
Series A
%6l I-
21 Jfu TORQUE TO
60-70 N'm
20
26 307-427
BUNG MOUNT ADJUSTABLE-LENGTH
PUMPS
IMax. 456 mm (18 in.) ad u s t m e n t )
\
Fits bung ty e contamers rom 724 mm (28.5in.)to
1180 mm d 4 in.) deep.
CARBON STEEL MODELS
REF PART DESCRIPTION ON
226949 rubber packed, nonmetered dispensing valve NO. NO.
226950 rubber packed, metered dispensing valve
Includes items 1-5, 101 to 104 and 202 to 208 1 215-963 AIR MOTOR
226951 rubber packed, less dispensing valve sea instruction manual 307456 1
Includes items 14, 101 to 104 and202 to 208 2 218-117 MOUNTING KIT for Carbon Steel
Pumps 226949.226950 and 226-951
Includes items 101 to 104 1
3 218-116 DISPL. PUMP
(for Z!5949, B 350 and 226951.
see page 2 8 )
4 218-316 AIR REGULATOR KIT
Includes items XQ to 208
218-115 VALVE KIT lfor 226-949, see instruc-
tion manual 307-6371
218-243 VALVE KIT (for 226-950.see instruc-
tion manual 307-637)
101 178-923 PIN, headed, straight
102 104-541 NUT, lock, M8, wlnylon insert
103 '177-171 TIE ROD
104 "180-166 PIN, clip
202 100-403 PLUG, pipe, 118 npt
rn 104-655 GAUGE, air pressure, 0-60 psi
10-4.2 bar), 118 npt inlet 1
204 104-815 REGULATOR, air, 0-80 psi
(04.2 bar) 888 instruction manual
". " .
307-204 1
NIPPLE, pipe, 1/8 npt 1
FITTING, air coupler, 118 npt(m) 1
COUPLER, air quick, 114 nptlfl inlet 1
BUSHING, pipe, 1/4x1/8 npt 1
3 7 numbers in descriptions refer to separate instruction
manuals.
Wecommended "tool box" spare parts. Keep on hend to
Ref No. 2 Mounting Kit reduce down time.
Includes items 101 to 104
Refer to "How To Order Replacement Perts"on page 37.
J
Ref No. 4 Air R e g u l a t o r Kir
Includes items 202 to 208
C A R B O N STEEL DISPLACEMENT PUMP
(for pump Model 226-949.226-950 and 228-951)
Model 218-116 30 to 275 gallon containersize, rubber packed. 218112 REPAIR KIT
Series A For DisplacementPump 218-116
28 307427
ACCESSORIES
(must be purchased separately)
4
210-865 LOW-LEVEL CUT-OFFVALVE
For installation instructions see page 3.
5
1 100-989 RING, retaining 1 :.
2 156-619 FLOAT 1 ::.
. ...
3 156-620 SPRING, extension 1 2
4 172-555 HOUSING, valve 1 1
5 202-314 VALVE, clapper 1
BUNG ADAPTERS
(Included with all 55 gallon drum size pumps).
214-583 Carbon Steel
214-592 Stainless Steel
104-542 SCREW, hex hd cap; M8 x 1.25 1
1 1 1104-587 SCREW, hex hd cap; M8 x 1.25
(stainless steel) 1
2 172-405 BUSHING. nvlon 1
MOUNTING, bung i
210-877 MOUNTING, bung; stainless steel 1
1
DRUM COVER 204-514
40 Liter (10 gallon) size and 60 liter (16 gallon) size.
AIR LINE FILTER m-ia Drum cover mounts on top of an open drum, with
14 bar 1200 psi1 MAXIMUM WORKING PRESSURE mounting holes for 1:l metric pump. Includes thumb-
112 npt inlet and outlet R screws anda rubber gasket.
A B C D
Pump Overall Pump Fluid Fluid Net
No. Length Length Inlet Outlet Weight
.
226-943 615mm 181 mm 1-112 in. 3/4in. 4.5 kg
228-944 124 in.) (7.1 in.) nptlf) nptlf) I10 Ibl
226-948
226-w
226-941 1315 mm 880 mm 1-1/2 in. 3/4 in. 6.5 kg
226-942 (51.7 in.) (34.6in.) npt(f) npt(f) (14.25 Ibl
226-947
226-953
226-949 3ispensing 7.7 kg
226-950 1158 mm'724 mm" Suction Valve 117 Ib)
145.6 in.) (28.5 in.) Tube
226-951 3/4 in. 7.2 kg
nptlf) (16 Ibl
I I I I I I
'Extends to 1614 mm (63.5 in.) overall; the pump length
to 1180 mm (46.4 in.).
307-427 31
TECHNICAL DATA
Recommended air operating
range-Models 226-940
226948.
through 226-945, 226-947,
226-952 and 226-953 : 3 to 12 bar 140-180psi)
"Models 226-949, 226-950,
226-951 : 3 to 4.2 bar (40 to 60 psi)
Air consumption : Approx. 0.05 m3lmin
(1.5 cfmlgal) at4 literslmin
(1 gpm)at 5.6 bar 1 8 0 psi)
input
Maximum recommended 250 cycleslmin: 37.8
pump speed : literslmin (10 gpml
Fluid outlet : 314 nptlf)
Air inlet : 114 nptlf)
Fluid inlet : 1-112 nptlfl
Wetted parts-Models
226-940, 226-941, 226.943, : Carbon Steel, 300 Series
22 69 44 Stainless Steel, Leather,
Cadmium-plated Ductile Iron.
Chrome and Zinc-plated
Steel, PTFE Polyethylene,
Tefzel"
-Model 226942 and 226-945 : 300 Series Stainless Steel,
Chrome, Tefzel? PTFE
-Models 226-947. 226.948.
226-949, 226-950, 226951 : Stainless Steel, buna-N,
Cadmium-plated Ductile Iron,
Chrome and Zinc-plated
Steel, PTFE Polyethylene,
Tefzel"
-Models 226-952 and
226-953 : 300 Series Stainless Steel,
Chrome, Rubber,PTFE
This warranlq is wnditioned upon the prepaidreturn of the equipment claimedto be defective for examination by Grew to verify the claimed
defect If the claimed defen b verified, Graw wil repair or replace frea of charge any defective parts. The equipment
will be returned to the
original purchaser tnnsrm&n prepaid. If insmion of the equipment d m not disclose any defen inmaterial or workmanship, repairs will be
made st a reasonable charge. which chargesm y include the the coots of parts, labor and transportation.
DISCLAIMERS ANDLIMIT&TIONS
Factory Branches: Atlanta, Dallas. Detrolt. Lo5 Angeles, West Caldwell IN.J.1
Subsidiary endAffiliate Companies: Canada; England: Switzerland; France: Germany; Hong Kong; Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1444
PRINTED IN U.S.A. 307-421 12-80 Revised 247