Professional Documents
Culture Documents
3 en 1 Mi Swaco
3 en 1 Mi Swaco
For
Mongoose PT Platform
Mud Cleaner
Per Assemblies:
9672360-03 = 2-12/6T4, 3 Motor 440-480V 60 Hz
9672360-03L = 2-12/6T4, 3 Motor 440-480V 60 Hz, Left Side Mount
9672360-07 = 2-12/6T4, 3 Motor 380-415V 50 Hz
9672360-07L = 2-12/6T4, 3 Motor 380-415V 50 Hz, Left Side Mount
9672360-11 = 2-12/6T4, 3 Motor 575-600V 60 Hz
9672360-11L = 2-12/6T4, 3 Motor 575-600V 60 Hz, Left Side Mount
9672360-88 = 2-12/6T4, 3 Motor 380-415 50 Hz
UL Approved
P. O. Box 42842
Houston, TX 77242-2842
Global Sales/Technical Support
Tel: 281-988-1866
Fax: 281-988-1889
Watts: 1-800-654-0660 Manual Part #: 90-90-997 Rev. D
DISCLAIMER
Recommendations made by M-I SWACO are advisory only. M-I SWACO shall
not be liable under any guarantees or warranties, expressed or implied, in any
manner or form, AND ALL WARRANTIES, EXPRESSED OR IMPLIED, ARE
HEREBY SPECIFICALLY EXCLUDED, and M-I SWACO shall not be liable
for the failure to obtain any particular results from the use of any recommendation
made by it or from the use of this material. In no event shall M-I SWACO be
liable for incidental or consequential damages.
All other products, brand, or trade names used in this publication are the trademarks or registered
trademarks of their respective owners.
All rights reserved. This publication is the property of, and contains information proprietary to M-I
SWACO. No part of this publication may be reproduced in any form or by any means, including
electronic, mechanical, or otherwise, without the prior written permission of M-I SWACO.
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
S O L I D S
C O N T R O L
Comparison of balanced elliptical motion to linear motion
Linear Motion
Specifications
• Length:
Linear motion 116 in.
(2,946 mm)
Dual motion 120 in.
(3,048 mm)
• Width 68.9 in.
(1,749 mm)
• Weir height 29 in.
(737 mm)
63
(1,600)
• Height 51 in.
31.5
(800)
(1,295 mm)
• Weight 3,800 lb
(1,724 kg)
Motion generator 0.6-hp Screen Deck and Screens
(voltage per customer contract)
Removable
inspection
explosion-proof • Screen area:
covers
(10-in. Gross: 29.4 ft2 (2.73 m2)
[254-mm] Motion generator 2-hp
opening) (voltage per customer contract) Net (API): 21.2 ft2 (1.97 m2)
explosion-proof
(2 places)
112.6
(2,860)
• Deck-angle adjustment:
–3° to +3°
• Screen type: Pre-tensioned
4 x 2 ft (1.2 x 0.61 m)
Basket Isolation
• Powder-coated steel springs
Motor Specifications
• Two (2) main 2-hp
vibrator motors
• One (1) additional 0.6-hp
vibrator motor on dual-
1.5 51 motion model
4XØ (38) (1,295)
21.8 • 460V/60 Hz/1,800 rpm or
(553)
Approx. 400V/50 Hz/1,500 rpm
C.G.
Approved
lifting point
Approved
• Explosion proof
30.3 (770) lifting point
63
Approximate C.G. • Class I, Groups C and D
(1,600)
64.5
(1,638)
• UL/cUL, CE, ATEX, NORSOK
68.9
(1,749) Basic Fluid Capacity
• 600 gpm (2,271 L/min)
Mud outlet
Deck-angle one each side 33.5 (851) 32.5 (826) Approved 10.5 (267) Approved
indicator lifting point 31.5 lifting point
one each side 92.9 (2,359)
(800) 10-in. (254-mm) inlet connection
104.4 (2,651) Earth
Unit nameplate weld cover plate
106.3 (2,701) grounding point
116 (2,946) (both sides)
REAR VIEW
Basic MONGOOSE PTshaker with possum belly
Specifications
• Length 123 in.
(3,123 mm)
• Width 68.9 in.
(1,749 mm)
• Weir height 29 in. (737 mm)
• Height 51 in.
(1,295 mm)
• Weight 4,070 lb
63 (1,600) (1,846 kg)
Screen Deck and Screens
• Screen area:
Gross: 29.4 ft2 (2.73 m2)
Motion generator 0.6-hp
(voltage per customer contract)
Net (API): 21.2 ft2 (1.97 m2)
explosion-proof
• Deck-angle adjustment:
Motion generator 2-hp –3° to +3°
(voltage per customer contract)
124.7
(3,167)
explosion-proof
2 places
• Screen type: Pre-tensioned
4 x 2 ft (1.2 x 0.61 m)
Basket Isolation
• Powder-coated steel springs
Motor Specifications
• Two (2) main 2-hp
vibrator motors
68.9 (1,749)
• One (1) additional 0.6-hp
vibrator motor on dual-
motion model
• 460V/60 Hz/1,800 rpm or
400V/50 Hz/1,500 rpm
4XØ 1.5
(38) 51 • Explosion proof
(1,295)
20.4
(517)
• Class I, Groups C and D
Approx.
Approved
C.G. • UL/cUL, CE, ATEX, NORSOK
lift point
Approved
30.3 (770)
Approximate C.G.
lift point Basic Fluid Capacity
63 (1,600)
64.5 (1,638)
• 600 gpm (2,271 L/min)
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
This documentation is intended for use by field engineering, installation, operation and repair personnel for the
proper installation and maintenance of equipment manufactured by M-I SWACO. Every effort has been made to
ensure the accuracy of the information contained herein. M-I SWACO will not be held liable for errors in this
material, or for consequences arising from misuse of this material.
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
TABLE OF CONTENTS
Page
Description
Number
Section 1.0 Symbols 1-4
1.1 Notes, Cautions & Warnings 3
1.2 Packing 3
1.3 Safety Warning Icons & Explanations 4
Notes, cautions and warnings appear throughout this manual to provide additional information and to advise on
specific actions to protect personnel from potential injury or fatal conditions. They also inform of actions necessary
to prevent equipment damage or conditions that may void equipment warranties.
: This symbol draws attention to safety measures which MUST be observed to prevent
PERSONAL injury.
ATTENTION! : This symbol draws attention to safety measures which MUST be observed to prevent
DAMAGE to equipment.
CAUTION: This symbol draws attention to safety measures which MUST be observed to prevent an
ACCIDENT from occurring.
WARNING: This symbol draws attention to safety measures which MUST be observed to prevent
PERSONAL injury.
NOTE: This symbol draws attention to general operating notes which should be especially
observed.
1.2 Packaging
The symbols that may be shown on the package are noted below. Their meanings are as follows:
The table below uses illustrations to provide easily recognizable safety concerns and responsibilities to
follow. Each illustration is accompanied with an explanation for the user to be readily alert for and pay
attention to during operation and maintenance of the equipment.
ELECTRICAL: Electrical wire to hand with HEAVY PARTS: Hand with heavy object
electricity symbol running through indicates on top indicates heavy parts can crush and
shock hazard is present. harm.
HEAVY PARTS: Foot with heavy object on MOVING PARTS: Human figure with an
top indicates heavy parts can crush them. arm caught between gears indicates moving
equipment parts present a danger to life or
limb.
MOVING PARTS: Hand with fingers caught CHEMICAL: Drops of liquid on hand
between gears indicates moving equipment parts indicates material will cause burns or
present a danger to life or limb. irritation to human skin or tissue.
EXPLOSION: Rapidly expanding symbol FIRE: Flame indicates material may ignite
indicates material may explode if subjected to and cause burns.
high temperatures, sources of ignition or high
pressure.
POISON: Skull and crossbones indicate that a VAPOR/FUMES: Human figure in a cloud
material is poisonous or is a danger to life. indicates that material vapors/fumes present
a danger to life or limb.
LOCK OUT: Open lock with direction arrow HOT: Hand over flame indicates that
indicates to operator to ensure ALL input power surfaces may be hot.
sources are locked out and tagged out according
to regulation.
FLYING PARTICLES: Arrows bouncing of HELMET PROTECTION: Arrow
face indicates parts/particles flying through air bouncing off head with helmet indicates
will harm face and present a danger to life or falling parts present a danger to life.
limb.
EAR PROTECTION: Headphones over ears ELECTRICAL: Electrical wire to arm with
indicate noise level will harm ears. electricity symbol running through human
body indicates shock hazard is present.
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
4. All personnel performing installation, operations and maintenance procedures on this equipment should be trained on rig
safety, operations and maintenance of this equipment.
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Weight
(Approximate) Dims. (mm)
Description Manufacturer Performance Materials Section
LxHxW
Dry Operating
Assembly: 9672360
2585 kg Assembly: 9672360
(5,700 lbs.) 4060 kg
See Data (8,950 lbs.)
Shale Carbon/ See Section
M-I SWACO Sheet 2.05
Shaker Stainless Steel Assembly: Assemby: 2.07
No. 2.05
9672365 9672365
2130 kg 3357 kg
(4,700 lbs.) (7,400 lbs.)
Assembly: Assembly:
9672385 9672385
2954 kg 5455 kg
(6,500 lbs.) (12,000 lbs.)
Assembly: Assembly:
9672380 9672380
2820 kg 5443 kg
(6200 lbs.) (12,000 lbs.)
Assembly: Assembly:
9672875 9672875
3356 kg 6214 kg
(7400 lbs.) (13,700 lbs.)
Small = 44 kg Small = 44 kg
AC Motor - Italvibras G. See Data (96 lbs.) (96 lbs)
Cast 572 x 270 x
Shale Silingardi Sheet 2.06
Iron 312
Shaker (Martin Motors) No. 2.06 Large = 98 kg (216 Large = 98 kg (216
lbs.) lbs.)
Electrical
Control Cast 235 x 387 x
Control N/A 18 kg (37 lbs.) 18 kg (37 lbs.) 8.07
Craft Aluminum 183
Station
Assembly: Assembly:
9672396 9672396
618 kg 1542 kg
(1360 lbs.) (3400 lbs.)
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Electrical
Description Input Output
Voltage Frequency
Power Power
Shale Shaker
1.305 kW
Including Feeder + 2 380-415V 1.5 kW 50 Hz
(1.75 hp)
& 3 Electric Motors
Shale Shaker
1.485 kW
Including Feeder + 2 440-480V 1.65 kW 60 Hz
(1.99 hp)
& 3 Electric Motors
Shale Shaker
1.485 kW
Including Feeder + 2 550-600V 1.65 kW 60 Hz
(1.99 hp)
& 3 Electric Motors
Shale Shaker
N/A
Including Feeder + 3 380-415V 0.52 kW 50 Hz
(0.495 hp)
Electric Motors
Shale Shaker
0.442 kW
Including Feeder + 3 440-480V 0.66 kW 60 Hz
(0.59 hp)
Electric Motors
Shale Shaker
0.442 kW
Including Feeder + 3 575-600V 0.66 kW 60 Hz
(0.59 hp)
Electric Motors
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
TABLE OF CONTENTS
Page
Description
Number
Isoflex Topas NB 52 3-5
Hercules Real Tuff Thread Sealant with Teflon 6-8
Food Grade Anti-Seize 9 -13
Superflex Red RTV Silicone Adhesive Sealant 14-18
Loctite Thread Sealant with Teflon 19-23
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
FUNCTIONAL REQUIREMENTS
ELECTRICAL
1.01 Rated System Voltage V : 220-240/380-415
1.02 Rated System Frequency Hz : 50
1.03 Winding Connection : Δ-Y
1.04 Duty Type : Continuous
1.05 Starting Method : Across-The-Line
1.06 Winding Temp. Sensors : N/A
1.07 Bearing Temp. Sensors : N/A
CONSTRUCTION
1.08 Gas Group : IIB
1.09 Temperature Class : 160C
1.10 Vibration Det. Motor >1000kW, Anti-Friction Bearing : N/A
1.11 Vibration Det. Motor >1000kW, Sleeve Bearing : N/A
1.12 Vibration Detection, 30kW<Motor <1000kW : N/A
ENVIRONMENTAL CONDITIONS
1.13 Ambient Temperature ºC : Max.: 55 (131°F)
1.14 Humidity % : 100
NOTES:
Continued . . .
PROJECT REQUIREMENTS
2.01 Tag No. : N/A
2.02 Unit : N/A
2.03 Service : N/A
2.04 Supplier : Martin Engineering
2.05 Manufacturer : Italvibras G. Silingaradi
2.06 Type : CDX18-5900
2.07 Location / Module : N/A
2.08 Job. No. : N/A
2.09 Inquiry No. : N/A
2.10 Quote No. : N/A
2.11 P.O. No : N/A
ELECTRICAL
2.12 Rated Voltage V : 220-240/380-415
2.13 Rated Output kW : 1.5
2.14 Max. Permissible Starting Current xIn : 40/23
2.15 Start Up Time Sec. : 1.11
2.16 No. of Starts Per Hour : N/A
CONSTRUCTION
2.17 Ex Classification : EExd IIB 160C
2.18 Degree of Protection IP : IP66
2.19 Insulation Class Stator F : F
2.20 Temperature Rise B/F : B
2.21 Instrument Air for Exp. System bar g : N/A
2.22 Bearing Vibration, Instrument Make/Type : N/A
2.23 Sound Pressure Level Lp dBA : <85
2.24 Cooling Method IC : N/A
2.25 Cooling Water Supply Temp. (Max. / Min.) ºC N/A
2.26 Cooling Water Supply Pressure (Max. / Min.) bar g : N/A
2.27 Heat Exchanger Material : N/A
2.28 Painting Specification Norsok/Other : SWACO Orange
2.29 Space Heater Yes/No : No
2.30 Winding Temperature Detection Yes/No : No
2.31 Motor Housing Material : Cast Iron
ENVIRONMENTAL CONDITIONS
2.32 Hazardous Area Classifications : N/A
2.33 Location Indoor/Outdoor : N/A
NOTES:
Continued . . .
PROJECT REQUIREMENTS
Continued . . .
Continued . . .
CONSTRUCTION (continued)
4.33 Cooling Water Design Pressure bar g : N/A
4.34 Cooling Water Leakage Detector Yes / No : N/A
4.35 Motor Housing Material : Cast Iron
4.36 Terminal Box Material : Cast Iron
4.37 Heat Exchanger Material : N/A
4.38 Cooling Fan Material : N/A
4.39 Frame Size : 60
4.40 Space Heater Voltage V : N/A
4.41 Space Heater Power W : N/A
4.42 Exp. Method Pressurization/Purge : N/A
4.43 Instrument Air Flow Rate m3/hr : N/A
4.44 Painting Specification : SWACO Orange
4.45 Temp. Detectors in Bearing Type/No. of : N/A
4.46 Temp. Detectors in Windings Type/No. of : N/A
MECHANICAL
4.47 Inertia J=GD² /4 kg m² : 0.44094
4.48 Rated Torque Nm : 7.40
4.49 Locked Rotor Torque % : 521
4.50 Breakdown Torque % : 476
4.51 Bearing Drive End Type/No. of : TVP2.C4
4.52 Bearing Non Drive End Type/No. of : TVP2.C4
4.53 Oil Quantity for Bearings l/Min. : N/A
4.54 Make / Type of Vibration Detectors : N/A
4.55 Lubrication System : Grease Fittings
4.56 Sound Pressure Level at 1 Meter, with Sinus Load Lp dB(A) : < 85
4.57 Weight Total kg : 98
4.58 Rotor Weight for Frame Size 250 kg : N/A
4.59 Shaft Standard/Double End/Extended : Double End
VARIOUS
4.60 Ex Certificate Issued by : KEMA
4.61 Ex Certificate Number : See Notes
4.62 Ex Classification : EExd IIB 160C
4.63 Dimensional Drawing No. : 88.60
4.64 Main Power Cable Entry Sizes : ¾” NPT
4.65 Heating/Cooling Time Constant (HV Motors) Min. : N/A
NOTES:
FUNCTIONAL REQUIREMENTS
ELECTRICAL
1.01 Rated System Voltage V : 220-240/440-480
1.02 Rated System Frequency Hz : 60
1.03 Winding Connection : Δ-Y
1.04 Duty Type : Continuous
1.05 Starting Method : Across-The-Line
1.06 Winding Temp. Sensors : N/A
1.07 Bearing Temp. Sensors : N/A
CONSTRUCTION
1.08 Gas Group : IIB
1.09 Temperature Class : 160C
1.10 Vibration Det. Motor >1000kW, Anti-Friction Bearing : N/A
1.11 Vibration Det. Motor >1000kW, Sleeve Bearing : N/A
1.12 Vibration Detection, 30kW<Motor <1000kW : N/A
ENVIRONMENTAL CONDITIONS
1.13 Ambient Temperature ºC : -20 to 55 ( -4 to 131ºF)
1.14 Humidity % : 100
NOTES:
Continued . . .
PROJECT REQUIREMENTS
2.01 Tag No. : N/A
2.02 Unit : N/A
2.03 Service : N/A
2.04 Supplier : Martin Engineering
2.05 Manufacturer : Italvibras G. Silingaradi
2.06 Type : CDX18-5900
2.07 Location / Module : N/A
2.08 Job. No. : N/A
2.09 Inquiry No. : N/A
2.10 Quote No. : N/A
2.11 P.O. No : N/A
ELECTRICAL
2.12 Rated Voltage V : 220-240/440-480
2.13 Rated Output kW : 1.99
2.14 Max. Permissible Starting Current xIn : 45/22.5
2.15 Start Up Time Min. / Max. sec. : 1/3
2.16 No. of Starts Per Hour : N/A
CONSTRUCTION
2.17 Ex Classification : EExd IIB 160C
2.18 Degree of Protection IP : IP66
2.19 Insulation Class Stator F : F
2.20 Temperature Rise B/F : B
2.21 Instrument Air for Exp. System bar g : N/A
2.22 Bearing Vibration, Instrument Make/Type : N/A
2.23 Sound Pressure Level Lp dBA : <85
2.24 Cooling Method IC : N/A
2.25 Cooling Water Supply Temp. (Max. / Min.) ºC N/A
2.26 Cooling Water Supply Pressure (Max. / Min.) bar g : N/A
2.27 Heat Exchanger Material : N/A
2.28 Painting Specification Norsok/Other : SWACO Orange
2.29 Space Heater Yes/No : No
2.30 Winding Temperature Detection Yes/No : No
2.31 Motor Housing Material : Cast Iron
ENVIRONMENTAL CONDITIONS
2.32 Hazardous Area Classifications : N/A
2.33 Location Indoor/Outdoor : N/A
NOTES:
Continued . . .
PROJECT REQUIREMENTS
Continued . . .
Continued . . .
CONSTRUCTION (continued)
4.33 Cooling Water Design Pressure bar g : N/A
4.34 Cooling Water Leakage Detector Yes / No : N/A
4.35 Motor Housing Material : Cast Iron
4.36 Terminal Box Material : Cast Iron
4.37 Heat Exchanger Material : N/A
4.38 Cooling Fan Material : N/A
4.39 Frame Size : 60
4.40 Space Heater Voltage V : N/A
4.41 Space Heater Power W : N/A
4.42 Exp. Method Pressurization/Purge : N/A
4.43 Instrument Air Flow Rate m3/hr : N/A
4.44 Painting Specification : SWACO Orange
4.45 Temp. Detectors in Bearing Type/No. of : N/A
4.46 Temp. Detectors in Windings Type/No. of : N/A
MECHANICAL
4.47 Inertia J=GD² /4 kg m² : 0.44094
4.48 Rated Torque Nm : 7.80
4.49 Locked Rotor Torque % : 521
4.50 Breakdown Torque % : 476
4.51 Bearing Drive End Type/No. of : TVP2.C4
4.52 Bearing Non Drive End Type/No. of : TVP2.C4
4.53 Oil Quantity for Bearings l/Min. : N/A
4.54 Make / Type of Vibration Detectors : N/A
4.55 Lubrication System : Grease Fittings
4.56 Sound Pressure Level at 1 Meter, with Sinus Load Lp dB(A) : < 85
4.57 Weight Total kg : 91
4.58 Rotor Weight for Frame Size 250 kg : N/A
4.59 Shaft Standard/Double End/Extended : Double End
VARIOUS
4.60 Ex Certificate Issued by : KEMA
4.61 Ex Certificate Number : See Notes
4.62 Ex Classification : EExd IIB 160C
4.63 Dimensional Drawing No. : 88.60
4.64 Main Power Cable Entry Sizes : ¾” NPT
4.65 Heating/Cooling Time Constant (HV Motors) Min. : N/A
NOTES:
FUNCTIONAL REQUIREMENTS
ELECTRICAL
1.01 Rated System Voltage V : 575-600V
1.02 Rated System Frequency Hz : 60
1.03 Winding Connection : Δ-Y
1.04 Duty Type : Continuous
1.05 Starting Method : Across-The-Line
1.06 Winding Temp. Sensors : N/A
1.07 Bearing Temp. Sensors : N/A
CONSTRUCTION
1.08 Gas Group : IIB
1.09 Temperature Class : 160C
1.10 Vibration Det. Motor >1000kW, Anti-Friction Bearing : N/A
1.11 Vibration Det. Motor >1000kW, Sleeve Bearing : N/A
1.12 Vibration Detection, 30kW<Motor <1000kW : N/A
ENVIRONMENTAL CONDITIONS
1.13 Ambient Temperature ºC : Max.: 55 (131°F)
1.14 Humidity % : 100
NOTES:
Continued . . .
PROJECT REQUIREMENTS
2.01 Tag No. : N/A
2.02 Unit : N/A
2.03 Service : N/A
2.04 Supplier : Martin Engineering
2.05 Manufacturer : Italvibras G. Silingaradi
2.06 Type : CDX18-5900
2.07 Location / Module : N/A
2.08 Job. No. : N/A
2.09 Inquiry No. : N/A
2.10 Quote No. : N/A
2.11 P.O. No : N/A
ELECTRICAL
2.12 Rated Voltage V : 575-600
2.13 Rated Output kW : 1.65
2.14 Max. Permissible Starting Current amp : 31.4/18
2.15 Start Up Time Sec. : 0.72
2.16 No. of Starts Per Hour : N/A
CONSTRUCTION
2.17 Ex Classification : EExd IIB 160C
2.18 Degree of Protection IP : IP66
2.19 Insulation Class Stator F : F
2.20 Temperature Rise B/F : B
2.21 Instrument Air for Exp. System bar g : N/A
2.22 Bearing Vibration, Instrument Make/Type : N/A
2.23 Sound Pressure Level Lp dBA : <85
2.24 Cooling Method IC : N/A
2.25 Cooling Water Supply Temp. (Max. / Min.) ºC N/A
2.26 Cooling Water Supply Pressure (Max. / Min.) bar g : N/A
2.27 Heat Exchanger Material : N/A
2.28 Painting Specification Norsok/Other : SWACO Orange
2.29 Space Heater Yes/No : No
2.30 Winding Temperature Detection Yes/No : No
2.31 Motor Housing Material : Cast Iron
ENVIRONMENTAL CONDITIONS
2.32 Hazardous Area Classifications : N/A
2.33 Location Indoor/Outdoor : N/A
NOTES:
Continued . . .
PROJECT REQUIREMENTS
Continued . . .
Continued . . .
CONSTRUCTION (continued)
4.33 Cooling Water Design Pressure bar g : N/A
4.34 Cooling Water Leakage Detector Yes / No : N/A
4.35 Motor Housing Material : Cast Iron
4.36 Terminal Box Material : Cast Iron
4.37 Heat Exchanger Material : N/A
4.38 Cooling Fan Material : N/A
4.39 Frame Size : 60X
4.40 Space Heater Voltage V : N/A
4.41 Space Heater Power W : N/A
4.42 Exp. Method Pressurization/Purge : N/A
4.43 Instrument Air Flow Rate m3/hr : N/A
4.44 Painting Specification : SWACO Orange
4.45 Temp. Detectors in Bearing Type/No. of : N/A
4.46 Temp. Detectors in Windings Type/No. of : N/A
MECHANICAL
4.47 Inertia J=GD² /4 kg m² : 0.44094
4.48 Rated Torque Nm : 7.2
4.49 Locked Rotor Torque L : -
4.50 Breakdown Torque % : -
4.51 Bearing Drive End Type/No .of : TVP2.C4
4.52 Bearing Non Drive End Type/No. of : TVP2.C4
4.53 Oil Quantity for Bearings oz. : 1.0 (25 grams)
4.54 Make / Type of Vibration Detectors : N/A
4.55 Lubrication System : Grease Fittings
4.56 Sound Pressure Level at 1 Meter, with Sinus Load Lp dB(A) : < 85
4.57 Weight Total kg : 91 (200 lb)
4.58 Rotor Weight for Frame Size 250 kg : N/A
4.59 Shaft Standard/Double End/Extended : Double End
VARIOUS
4.60 Ex Certificate Issued by : KEMA
4.61 Ex Certificate Number : See Notes
4.62 Ex Classification : EExd IIB 160C
4.63 Dimensional Drawing No. : -
4.64 Main Power Cable Entry Sizes : ¾” NPT
4.65 Heating/Cooling Time Constant (HV Motors) Min. : N/A
NOTES:
FUNCTIONAL REQUIREMENTS
ELECTRICAL
1.01 Rated System Voltage V : 380-415V
1.02 Rated System Frequency Hz : 50
1.03 Winding Connection : Δ-Y
1.04 Duty Type : Continuous
1.05 Starting Method : Across-The-Line
1.06 Winding Temp. Sensors : N/A
1.07 Bearing Temp. Sensors : N/A
CONSTRUCTION
1.08 Gas Group : IIB
1.09 Temperature Class : T4
1.10 Vibration Det. Motor >1000kW, Anti-Friction Bearing : N/A
1.11 Vibration Det. Motor >1000kW, Sleeve Bearing : N/A
1.12 Vibration Detection, 30kW<Motor <1000kW : N/A
ENVIRONMENTAL CONDITIONS
1.13 Ambient Temperature ºC : Max.: 40 (104°F)
1.14 Humidity % : 100
NOTES:
Continued . . .
PROJECT REQUIREMENTS
2.01 Tag No. : N/A
2.02 Unit : N/A
2.03 Service : N/A
2.04 Supplier : Martin Engineering
2.05 Manufacturer : Italvibras G. Silingaradi
2.06 Type : CDX18-2100
2.07 Location / Module : N/A
2.08 Job. No. : N/A
2.09 Inquiry No. : N/A
2.10 Quote No. : N/A
2.11 P.O. No : N/A
ELECTRICAL
2.12 Rated Voltage V : 380-415
2.13 Rated Output kW : 0.52
2.14 Max. Permissible Starting Current amp : 6.5/3.76
2.15 Start Up Time Sec. : 2.17
2.16 No. of Starts Per Hour : N/A
CONSTRUCTION
2.17 Ex Classification : EExd IIB T4
2.18 Degree of Protection IP : IP66-7
2.19 Insulation Class Stator F : F
2.20 Temperature Rise B/F : B
2.21 Instrument Air for Exp. System bar g : N/A
2.22 Bearing Vibration, Instrument Make/Type : N/A
2.23 Sound Pressure Level Lp dBA : <85
2.24 Cooling Method IC : N/A
2.25 Cooling Water Supply Temp. (Max. / Min.) ºC N/A
2.26 Cooling Water Supply Pressure (Max. / Min.) bar g : N/A
2.27 Heat Exchanger Material : N/A
2.28 Painting Specification Norsok/Other : SWACO Orange
2.29 Space Heater Yes/No : No
2.30 Winding Temperature Detection Yes/No : No
2.31 Motor Housing Material : Cast Iron
ENVIRONMENTAL CONDITIONS
2.32 Hazardous Area Classifications : N/A
2.33 Location Indoor/Outdoor : N/A
NOTES:
Continued . . .
PROJECT REQUIREMENTS
Continued . . .
Continued . . .
CONSTRUCTION (continued)
4.33 Cooling Water Design Pressure bar g : N/A
4.34 Cooling Water Leakage Detector Yes / No : N/A
4.35 Motor Housing Material : Cast Iron
4.36 Terminal Box Material : Cast Iron
4.37 Heat Exchanger Material : N/A
4.38 Cooling Fan Material : N/A
4.39 Frame Size : 30X
4.40 Space Heater Voltage V : N/A
4.41 Space Heater Power W : N/A
4.42 Exp. Method Pressurization/Purge : N/A
4.43 Instrument Air Flow Rate m3/hr : N/A
4.44 Painting Specification : SWACO Orange
4.45 Temp. Detectors in Bearing Type/No. of : N/A
4.46 Temp. Detectors in Windings Type/No. of : N/A
MECHANICAL
4.47 Inertia J=GD² /4 kg m² : 0.44094
4.48 Rated Torque Nm : 2.5
4.49 Locked Rotor Torque L : -
4.50 Breakdown Torque % : -
4.51 Bearing Drive End Type/No. of : TVP2.C4
4.52 Bearing Non Drive End Type/No. of : TVP2.C4
4.53 Oil Quantity for Bearings oz. : 0.4 (9 grams)
4.54 Make / Type of Vibration Detectors : N/A
4.55 Lubrication System : Grease Fittings
4.56 Sound Pressure Level at 1 Meter, with Sinus Load Lp dB(A) : < 85
4.57 Weight Total kg : 46 (101lb)
4.58 Rotor Weight for Frame Size 250 kg : N/A
4.59 Shaft Standard/Double End/Extended : Double End
VARIOUS
4.60 Ex Certificate Issued by : KEMA
4.61 Ex Certificate Number : See Notes
4.62 Ex Classification : EExd IIB T4
4.63 Dimensional Drawing No. : -
4.64 Main Power Cable Entry Sizes : ¾” NPT
4.65 Heating/Cooling Time Constant (HV Motors) Min. : N/A
NOTES:
FUNCTIONAL REQUIREMENTS
ELECTRICAL
1.01 Rated System Voltage V : 440-480V
1.02 Rated System Frequency Hz : 60
1.03 Winding Connection : Δ-Y
1.04 Duty Type : Continuous
1.05 Starting Method : Across-The-Line
1.06 Winding Temp. Sensors : N/A
1.07 Bearing Temp. Sensors : N/A
CONSTRUCTION
1.08 Gas Group : IIB
1.09 Temperature Class : T4
1.10 Vibration Det. Motor >1000kW, Anti-Friction Bearing : N/A
1.11 Vibration Det. Motor >1000kW, Sleeve Bearing : N/A
1.12 Vibration Detection, 30kW<Motor <1000kW : N/A
ENVIRONMENTAL CONDITIONS
1.13 Ambient Temperature ºC : Max.: 40 (104°F)
1.14 Humidity % : 100
NOTES:
Continued . . .
PROJECT REQUIREMENTS
2.01 Tag No. : N/A
2.02 Unit : N/A
2.03 Service : N/A
2.04 Supplier : Martin Engineering
2.05 Manufacturer : Italvibras G. Silingaradi
2.06 Type : CDX18-2100
2.07 Location / Module : N/A
2.08 Job. No. : N/A
2.09 Inquiry No. : N/A
2.10 Quote No. : N/A
2.11 P.O. No : N/A
ELECTRICAL
2.12 Rated Voltage V : 440-480
2.13 Rated Output kW : 0.442
2.14 Max. Permissible Starting Current amp : 8.52/4.26
2.15 Start Up Time Sec. : 0.72
2.16 No. of Starts Per Hour : N/A
CONSTRUCTION
2.17 Ex Classification : EExd IIB T4
2.18 Degree of Protection IP : IP66
2.19 Insulation Class Stator F : F
2.20 Temperature Rise B/F : B
2.21 Instrument Air for Exp. System bar g : N/A
2.22 Bearing Vibration, Instrument Make/Type : N/A
2.23 Sound Pressure Level Lp dBA : <85
2.24 Cooling Method IC : N/A
2.25 Cooling Water Supply Temp. (Max. / Min.) ºC N/A
2.26 Cooling Water Supply Pressure (Max. / Min.) bar g : N/A
2.27 Heat Exchanger Material : N/A
2.28 Painting Specification Norsok/Other : SWACO Orange
2.29 Space Heater Yes/No : No
2.30 Winding Temperature Detection Yes/No : No
2.31 Motor Housing Material : Cast Iron
ENVIRONMENTAL CONDITIONS
2.32 Hazardous Area Classifications : N/A
2.33 Location Indoor/Outdoor : N/A
NOTES:
Continued . . .
PROJECT REQUIREMENTS
Continued . . .
Continued . . .
CONSTRUCTION (continued)
4.33 Cooling Water Design Pressure bar g : N/A
4.34 Cooling Water Leakage Detector Yes / No : N/A
4.35 Motor Housing Material : Cast Iron
4.36 Terminal Box Material : Cast Iron
4.37 Heat Exchanger Material : N/A
4.38 Cooling Fan Material : N/A
4.39 Frame Size : 30X
4.40 Space Heater Voltage V : N/A
4.41 Space Heater Power W : N/A
4.42 Exp. Method Pressurization/Purge : N/A
4.43 Instrument Air Flow Rate m3/hr : N/A
4.44 Painting Specification : SWACO Orange
4.45 Temp. Detectors in Bearing Type/No. of : N/A
4.46 Temp. Detectors in Windings Type/No. of : N/A
MECHANICAL
4.47 Inertia J=GD² /4 kg m² : 0.44094
4.48 Rated Torque Nm : 2.5
4.49 Locked Rotor Torque L : -
4.50 Breakdown Torque % : -
4.51 Bearing Drive End Type/No. of : TVP2.C4
4.52 Bearing Non Drive End Type/No. of : TVP2.C4
4.53 Oil Quantity for Bearings oz. : 0.4 (9 grams)
4.54 Make / Type of Vibration Detectors : N/A
4.55 Lubrication System : Grease Fittings
4.56 Sound Pressure Level at 1 Meter, with Sinus Load Lp dB(A) : < 85
4.57 Weight Total kg : 44 (96lb)
4.58 Rotor Weight for Frame Size 250 kg : N/A
4.59 Shaft Standard/Double End/Extended : Double End
VARIOUS
4.60 Ex Certificate Issued by : KEMA
4.61 Ex Certificate Number : See Notes
4.62 Ex Classification : EExd IIB T4
4.63 Dimensional Drawing No. : -
4.64 Main Power Cable Entry Sizes : ¾” NPT
4.65 Heating/Cooling Time Constant (HV Motors) Min. : N/A
NOTES:
FUNCTIONAL REQUIREMENTS
ELECTRICAL
1.01 Rated System Voltage V : 575-600V
1.02 Rated System Frequency Hz : 60
1.03 Winding Connection : Δ-Y
1.04 Duty Type : Continuous
1.05 Starting Method : Across-The-Line
1.06 Winding Temp. Sensors : N/A
1.07 Bearing Temp. Sensors : N/A
CONSTRUCTION
1.08 Gas Group : IIB
1.09 Temperature Class : T4
1.10 Vibration Det. Motor >1000kW, Anti-Friction Bearing : N/A
1.11 Vibration Det. Motor >1000kW, Sleeve Bearing : N/A
1.12 Vibration Detection, 30kW<Motor <1000kW : N/A
ENVIROMENTAL CONDITIONS
1.13 Ambient Temperature ºC : Max.: 40 (104°F)
1.14 Humidity % : 100
NOTES:
Continued . . .
PROJECT REQUIREMENTS
2.01 Tag No. : N/A
2.02 Unit : N/A
2.03 Service : N/A
2.04 Supplier : Martin Engineering
2.05 Manufacturer : Italvibras G. Silingaradi
2.06 Type : CDX18-2100
2.07 Location / Module : N/A
2.08 Job. No. : N/A
2.09 Inquiry No. : N/A
2.10 Quote No. : N/A
2.11 P.O. No : N/A
ELECTRICAL
2.12 Rated Voltage V : 575-600
2.13 Rated Output kW : 0.442
2.14 Max. Permissible Starting Current amp : 5.94/3.41
2.15 Start Up Time Sec. : 1.79
2.16 No. of Starts Per Hour : N/A
CONSTRUCTION
2.17 Ex Classification : EExd IIB T4
2.18 Degree of Protection IP : IP66-7
2.19 Insulation Class Stator F : F
2.20 Temperature Rise B/F : B
2.21 Instrument Air for Exp. System bar g : N/A
2.22 Bearing Vibration, Instrument Make/Type : N/A
2.23 Sound Pressure Level Lp dBA : <85
2.24 Cooling Method IC : N/A
2.25 Cooling Water Supply Temp. (Max. / Min.) ºC N/A
2.26 Cooling Water Supply Pressure (Max. / Min.) bar g : N/A
2.27 Heat Exchanger Material : N/A
2.28 Painting Specification Norsok/Other : SWACO Orange
2.29 Space Heater Yes/No : No
2.30 Winding Temperature Detection Yes/No : No
2.31 Motor Housing Material : Cast Iron
ENVIRONMENTAL CONDITIONS
2.32 Hazardous Area Classifications : N/A
2.33 Location Indoor/Outdoor : N/A
NOTES:
Continued . . .
PROJECT REQUIREMENTS
Continued . . .
Continued . . .
CONSTRUCTION (continued)
4.33 Cooling Water Design Pressure bar g : N/A
4.34 Cooling Water Leakage Detector Yes / No : N/A
4.35 Motor Housing Material : Cast Iron
4.36 Terminal Box Material : Cast Iron
4.37 Heat Exchanger Material : N/A
4.38 Cooling Fan Material : N/A
4.39 Frame Size : 30X
4.40 Space Heater Voltage V : N/A
4.41 Space Heater Power W : N/A
4.42 Exp. Method Pressurization/Purge : N/A
4.43 Instrument Air Flow Rate m3/hr : N/A
4.44 Painting Specification : SWACO Orange
4.45 Temp. Detectors in Bearing Type/ No .of : N/A
4.46 Temp. Detectors in Windings Type/ No. of : N/A
MECHANICAL
4.47 Inertia J=GD² /4 kg m² : 0.44094
4.48 Rated Torque Nm : 2.5
4.49 Locked Rotor Torque L : -
4.50 Breakdown Torque % : -
4.51 Bearing Drive End Type/ No. of : TVP2.C4
4.52 Bearing Non Drive End Type/ No. of : TVP2.C4
4.53 Oil Quantity for Bearings oz. : 1.0 (25 grams)
4.54 Make / Type of Vibration Detectors : N/A
4.55 Lubrication System : Grease Fittings
4.56 Sound Pressure Level at 1 Meter, with Sinus Load Lp dB(A) : < 85
4.57 Weight Total kg : 44 (96lb)
4.58 Rotor Weight for Frame Size 250 kg : N/A
4.59 Shaft Standard/Double End/Extended : Double End
VARIOUS
4.60 Ex Certificate Issued by : KEMA
4.61 Ex Certificate Number : See Notes
4.62 Ex Classification : EExd IIB T4
4.63 Dimensional Drawing No. : -
4.64 Main Power Cable Entry Sizes : ¾“ NPT
4.65 Heating/Cooling Time Constant (HV Motors) Min. : N/A
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Date
*Operating weight based on fluid density of approximately 15 lbs/gal (1.8 specific gravity).
Date
*Operating weight based on fluid density of approximately 15 lbs/gal (1.8 specific gravity).
Date
*Operating weight based on fluid density of approximately 15 lbs/gal (1.8 specific gravity).
Date
*Operating weight is based on a fluid density of approximately 15 lbs/gal (1.8 specific gravity).
Date
*Operating weight based on fluid density of approximately 15 lbs/gal (1.8 specific gravity).
Date
*Operating weight based on fluid density of approximately 15 lbs/gal (1.8 specific gravity).
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
The Mongoose Platform fluid distribution system enhances solids separation performance. Screening operation improves
when forward momentum (kinetic energy) of drilling fluid is reduced and applied to the beginning of the feed screen. The
fluid distribution system at the rear of the shaker basket is mounted above the screen deck. Fluid is redirected from the inlet
line through a diverter box into a half pipe. Flow enters the half pipe at the bottom and spins up and back through the fluid
curtain reducing fluid velocity before making contact with the screen surface. Since fluid distribution is mounted above the
screen deck, no trap exists to collect solids. As fluid passes through the diverter box, it sweeps the box clean.
The shaker is equipped with two (2) or three (3) explosion proof vibratory motors. The unique mounting of these vibrators
produce a true linear motion for a two (2) motor version. The three (3) motor version has an adjustable dual motion drive
allowing the user to switch between linear and balanced elliptical motion while unit is in operation.
*See Tables 3-11 and Figure 1 for Performance Curve for more information.
The solids discard rate from the hydroclones is relatively low compared to the shaker capacity. This enables fine mesh
screens to be used, minimizing the fine solids returned to the active fluid system. Long beach lengths on the shaker enable a
high fluid recovery rate.
Efficient use of D-Silters reduce the solids content of drilling fluid; increases penetration rate; improves well bore conditions;
and, reduces pump maintenance.
M-I SWACO D-Silters are hydrocyclone solids separators. They remove “sand” and “silt” size particles from the drilling
fluid. Size clones to process 150% of the circulation rate and feed mud from the desanded mud compartment. M-I SWACO
clones are designed for excellent separation at about 45 psi (3.16 kg/cm²) input pressure for 9.5 ppg (1.14 kg/liter) mud.
Throughput capacity is increased at higher feed pressures with silt removal of finer silts improved, but not enough to offset
the increased wear rate. Separation is more efficient in low viscosity mud and in mud with low total solids content.
Polyurethane hydroclones are designed for lower cost and easier installation and replacement. Polyurethane also provides
longer wear-life, corrosion resistance and elimination of steel case housing. Each polyurethane 12” clone processes 500 gpm
(113.5 m³/hr) at 45 psi (3.16 kg/cm²) feed pressure. Each polyurethane twin 4” consists of two 4” hydrocyclones with
common feed rate of 150 gpm (36.6 m³) at 45 psi (3.16 kg/cm²) feed pressure.
The M-I SWACO D-Sander is used extensively to remove “sand” size particles from the drilling fluids.
NOTE: “Sand” refers to all particles larger than 74 microns. The word “sand” applies only to size. The solids themselves
may actually be shale, limestone, silica sand, barite or any other material of sand size which may be present.
The D-Sander removes 95% of particles larger than 74 microns, and up to 50% of particles between 74 and 40 microns. The
D-Sander can efficiently handle any combination of rig pump and sand conditions. The 12-inch cone reduces sand content to
a trace in normal drilling fluids. The compounded polyurethane cones are extremely durable with long in-service life
expectancy.
The cones are designed to deliver outstanding wear resistance (up to three times the service life of conventional rubber-lined
metal units). They are cast in four polyurethane sections to counteract uneven wear characteristics caused by sand, abrasive
cuttings and flow. The tapered cone section is joined together by stainless steel quick-release clamps in the feed unit This
enables easier handling, installation and maintenance while minimizing downtime.
The inlet (feed) section is designed to reduce potential turbulence when channeling slurry into the cone preventing it from
mixing back into the incoming feed. The tapered cone separates the fines and fluids from sand and cuttings while delivering
them to the return outlet and discarding the sand and cuttings through the outlet port. This design is efficient and capable of
processing more fluid at a given operating pressure. (See Tables 3-11 and Figure 1 for more information.)
D-Silter
The M-I SWACO D-Silter is used extensively to remove “silt” size particles from the drilling fluids. “Silt” refers to all
particles smaller than sand size (74 microns) and larger than colloidal material (about 2 microns). The word “silt” applies
here only to size. Solids may actually be shale, limestone, silica sand, barite or any other material of silt size which may be
present. The D-Silter removes nearly all particles larger than 25 microns.
The TWIN-CONE™ hydroclone design provides easy replacement of the urethane wear resistant feed and apex sections. The
D-Silter components include:
Six inch [6” (152 mm)] diameter feed and discharge manifolds
Victaulic couplings
0-60 psi (4.1 bars) pressure gauge.
Solids discharge trough with a built-in bypass mechanism
Six inch [6” (152 mm)] diameter solids discharge nipple
One inch [1” (25 mm)] NPT wash line connection.
Particle Size
Classification Screen Mesh Size
Microns
Larger Than 2000 Coarse 10 Mesh
2000-250 Intermediate 60 Mesh
250-74 Medium 200 Mesh
74-44 Fine 325 Mesh
44-2 Ultrafine -
2-0 Colloidal -
The D-Silter capacity is 1500 GPM [5678 LPM] (10T4 D-Silter). The solids discard rate from the hydroclones is relatively
low compared to the shaker capacity. This enables fine mesh screens to be used, minimizing the fine solids returned to the
active fluid system. Long beach lengths on the shaker enable a high fluid recovery rate.
Efficient use of D-Silters reduces solids content of drilling fluid; increases penetration rate; improves well bore conditions; and, reduces
pump maintenance.
*Head required (feet) at feed manifold for various pressures and mud weights.
Rate
70 80 90 100 110 120 ft.
(GPM)
500 8-7/8 9-3/8 9 -7/8 10-1/2 10-5/8 11 in.
750 9-1/8 9-1/2 10 10-3/8 10-5/8 11-1/8
900 9-1/4 9-5/8 10 10-3/8 10-3/4 11-1/4
1000 9-3/8 9-3/4 10-1/8 10-1/2 1 0-7/8 11-1/4
1250 9-3/4 10 10-3/8 10-3/4 11 11-1/2
1500 10-3/4 10-7/8 11-1/4 11-3/4 12 --
*Impeller sizes for mission 5 x 6 pumps at 1600 rpm for various volume rates and
pressure heads at pumps.
Rate
70 80 90 100 110 120 ft.
(GPM)
500 8-3/8 8-3/4 9-1/8 9-1/2 9-7/8 10-1/4
750 8-3/8 8-7/8 9-1/4 9-5/8 10 10-1/4
900 8-1/2 9 9-3/8 9-5/8 10 10-3/8
1000 8-5/8 9-1/8 9-3/8 9-3/4 10-1/8 10-3/8
1250 9-1/8 9-3/8 9-3/4 10-1/4 10-3/8 10-5/8
1500 9-5/8 10 10-1/4 10-1/2 10-7/8 11-1/8
*Impeller sizes for mission 5 x 6 pumps at 1750 rpm for various volume rates and
pressure heads at pumps.
Rate
70 80 90 100 110 120 ft.
(GPM)
500 9-3/8 9-3/4 10-1/8 10-1/2 10-7/8 11-3/8 in.
750 9-1/2 9-7/8 10-3/8 10-5/8 11 11-1/2
900 9-1/2 10 10-3/8 10-5/8 11-1/8 11-1/2
1000 9-3/4 10-1/8 10-1/2 10-7/8 11-1/8 11-5/8
1250 10-1/8 10-3/8 10-3/4 11-1/8 11-1/2 11-7/8
1500 10-3/8 10-3/4 11-1/8 11-3/8 11-3/4 12
*Impeller sizes for mission 6 x 8 pumps at 1600 rpm for various volume rates and pressure
heads at pumps.
Rate
70 80 90 100 110 120 ft.
(GPM)
500 -- 9-1/8 9-1/2 9-7/8 10-1/8 10-1/2 in.
750 -- 9-1/4 9-3/4 10 10-3/8 10-5/8
900 9 9-3/8 9-3/4 10-1/8 10-3/8 10-3/4
1000 9-1/8 9-1/2 9-7/8 10-1/8 10-1/2 10-7/8
1250 9-3/8 9-3/4 10-1/8 10-3/8 10-3/4 10-7/8
1500 9-5/8 10-1/8 10-3/8 10-5/8 11 --
*Impeller sizes for mission 6 x 8 pumps at 1750 rpm for various volume rates and pressure
heads at pumps.
Rate
70 80 90 100 110 120 ft.
(GPM)
500 14 16 18 21 23 26 hp
750 19 22 24 27 29 33
900 22 25 27 30 34 38
1000 24 27 30 34 37 41
1250 28 30 35 38 41 48
1500 40 47 52 57 60 --
Rate
70 80 90 100 110 120 ft.
(GPM)
500 16 17 18 20 23 26
750 19 22 24 27 29 32
900 23 25 28 30 33 37
1000 25 28 30 33 37 40
1250 31 34 37 41 45 49
1500 42 45 49 54 58 63
Rate
70 80 90 100 110 120 ft.
(GPM)
500 21 22 25 28 30 33 hp
750 24 28 31 34 36 39
900 28 31 34 37 41 44
1000 30 33 37 40 44 47
1250 36 40 43 48 50 --
1500 44 48 51 54 -- --
Rate
70 80 90 100 110 120 ft.
(GPM)
500 24 24 27 29 32 35 hp
750 28 29 33 35 38 42
900 39 32 35 39 43 46
1000 30 35 39 42 45 48
1250 35 42 46 50 54 58
1500 43 49 54 58 63 66
Unweighted Muds
Use the Mud Cleaner to clean the underflow of larger low gravity solids which have passed through the shakers and D-
Sanders.
Weighted Muds
The Mud Cleaner D-Silter cones remove most drill solids larger than about 25 microns and barite larger than 16 microns from
the mud system and deposits them on shaker screens. Solids larger than the micron opening of the screen are carried off the
end to the waste pit. Barite, along with liquid phase from the underflow, falls through the screen and returns to the mud
system.
Oil Muds
In some cases, the effectiveness of hydroclone separators may be slightly reduced due to the normal high viscosity of the oil
muds.
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
TABLE OF CONTENTS
Page
Item
Number
1.0 Installation 3-5
1.1 Equipment Location 3
1.2 Installation 4
1.3 Inlet Lines & Bypass Connections 4-5
2.0 Start-Up 5-9
2.1 External Power/Electrical Connection 5-6
2.2 Start-Up Procedures 6-8
Commissioning Check Sheet 11
The Mongoose Platform Shaker is supplied with an integral skid and is positioned directly onto the deck or
above sand traps as required. Install, operate and maintain equipment only with qualified personnel.
Locate unit at proper site. Shaker installation varies depending on rig circumstances and any special
requirements.
Use lifting lugs located on the unit. The label shown below indicates location of each lifting lug on the
unit.
Remove the four shipping brackets once unit is in place. Keep brackets for future movement or long term
storage.
If unit is installed indoors, adequate ventilation is necessary. Ventilation set-up may be done by qualified
M-I SWACO personnel or by the customer.
Use each of the four corners to bolt shaker into place. The feeder assembly is designed to allow users to
bolt on a 10” 150 lb pipe flange to permit true cold installation (box feeder version only). Check all nuts,
bolts and fasteners on shaker for tightness.
The Mongoose PT Platform Mud Cleaner is shipped as a complete assembly and positioned directly
onto the deck or above sand traps as required. Mount unit as level as possible BEFORE welding or
bolting unit to the tank (deviations will alter screen separating characteristics). The pump feeding the
clones operates best with a flooded suction. If possible, mount pump below normal operating mud
level in the pit. Otherwise, keep suction lifted as little as possible using a check valve or foot valve in
the suction line. Installed screens should lay flat and fit snug.
Install, operate and maintain equipment only with qualified personnel. Locate unit at proper site. Installation
varies depending on rig circumstances and any special requirements. Remove the four shipping brackets once
unit is in place. Keep brackets for future movement or long term storage.
If unit is installed indoors, adequate ventilation is necessary. Ventilation set-up may be done by qualified M-I
SWACO personnel or by the customer.
Use each of the four corners to bolt shaker into place. The feeder assembly is designed to allow users to bolt on
a 10” 150 lb pipe flange to permit true cold installation (box feeder version only). Check all nuts, bolts and
fasteners on shaker for tightness.
IMPORTANT: The Mongoose PT Platform with a standard skid (Part No. 9672140) is capable of handling approximately
600 gallons per minute from the flow line. A single effluent mud outlet gate is capable of handling approximately 1200
gallons per minute. Two Mongoose PT Platforms co-joined in series can handle 1200 gallons per minute when operated in
series using one effluent mud outlet gate.
Do NOT co-join three or more individual Mongoose PT Platforms with standard skids to operate in a series if flow
EXCEEDS 1200 gallons per minute. Skids allowing flow rates of 2400 gallons per minute (Part No. 9672610) through a
single effluent mud outlet gate are available for operating three or four shakers in series. Contact M-I SWACO for additional
information on Mongoose PT Platform multiple shaker options and configurations.
The mud cleaner is equipped with inlet line connections located on both the D-Sander and D-Silter, as well as a
bypass line (Refer to Figure 1.) Inlet lines allow fluid to flow from mud cleaner equipment to shaker screens.
The bypass line connection is used only when necessary for fluid flow to bypass shaker screens. Refer to
Section5.01 for bypass operation information.
D-Sander D-Silter
Model Overflow Inlet Model Overflow Inlet
2-12 10” 8” 8T4 8” 6”
3-12 12” 10” 10T4 10” 8”
NOTE: Assembly 9672365 does not have a D-Sander as shown in Figure 1.
2.0 Start-Up
b. Inlet port is located on side of control box. Remove plug seal on control panel box side to access
connection port opening (Refer to Figure 1).
Figure
Cable Gland Connection Port
(Exterior View of Control Box)
c. Insert cable gland and wires through connection port. The green wire is the grounding cable and the white,
red and black wires are all live power sources (Refer to Figure 2).
d. Ground green wire attaching an eyelet wire nut to the wire ends.
Green
Grounding
Cable
Figure 2
Connection to Outside/External Power
(Interior View of Control Box)
a. Locate unit at proper site. Evaluate site as an approved and appropriate location for the equipment.
Ensure site is compatible to space and power supply requirements.
Figure 3
Shipping Brackets
NOTE: Large motors should be fixed at 100% and smaller motors should be pre-set at 100%.
c. Re-assemble one cover to each vibrator; leaving one cover off of each vibrator.
NOTE: Bump start motors by pushing START button located on control panel. Next, quickly push STOP
button on control panel.
Mongoose Platform
Document Title: Installation & Commissioning Procedures
Section 4.01 7
e. Check direction of top counterweights. Vibrators should rotate as indicated in Figure 4 with unit labeled
showing rotation direction. (Refer to Figure 4.)
Feed End of
Unit
Discharge End
of Unit
Figure 4
Vibrator Rotational Direction
NOTE: If motors do not rotate in correct directions, switch the red and black wires while keeping the
white wire in the middle then bump start motors again to verify proper rotation as shown in Figure 4.
g. Start up unit and run for approximately 1 hour. Allow enough time for bearings to reach normal running
temperature.
Figure 5
Volt Meter Placed Around Motor Cable
EM3C00111 6912002
Voltage: 220-240/440-480V Voltage: 220-240/440-480V
Nominal Amps: 5.8/2.9 Nominal Amps: 1.79/0.88
EM3C00110 6905003
Voltage: 220-240/380-415V Voltage: 220-240/380-415V
Nominal Amps: 5.4/3.1 Nominal Amps: 1.47/0.85
EM3C00137 EM3C00038
Voltage: 575-600V Voltage: 575-600V
Nominal Amps: 2.3 Nominal Amps: 0.71
Mongoose Platform
Document Title: Installation & Commissioning Procedures
Section 4.01 9
THIS PAGE INTENTIONALLY LEFT BLANK
P&ID's Tag #
Reference M-I SWACO
Interconnect Type
Documents Data
Other Location
Energy Y N N/A Comments
Rig to Provide
Water Y N N/A Comments
for Commissioning
Air Y N N/A Comments
M-I SWACO Assets # Equipment Platform
Refer Numbers Serial # Description: Shale Shaker
6 Check all electrical box connections for proper gland seals. Y N N/A
9 Y N N/A
10 Y N N/A
11 Y N N/A
Y N N/A
Completed By Completed By
Date Date
Mongoose Platform
Document Title: Installation & Commissioning Procedures
Section 4.01 11
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
1.1 Unpacking
Equipment is delivered to the site as palletized units. The total number of packages delivered depends on the
quantity and configuration of the system required. The D-Sander and D-Silter are pre-assembled to the unit
before shipping.
Always use trained personnel for lifting and loading operations. Ensure lifting equipment is suitable for
purpose and is certified where necessary.
Use the four (4) lifting lugs located at each of the four corners of the unit. The label shown below indicates
location of each lifting lug on the unit.
NOTE: When assembled, unit should weigh between 618 – 3356 kg (1360 – 7400 lbs.), depending on
assembly. (See Section 2.07, Weight Data Sheets, for more detailed information per assembly.)
The Mongoose PT Platform Shale Shaker is designed on a modular basis and can be disassembled into
components for easier installation (if required). (Refer to Table 1 for further disassembly details.)
Lifting
Component
Method
Use soft slings around basket or spring mounting system to lift.
Weight-Approximately 900 kg (1,982 lbs.)
Lifting
Component
Method
NOTE: The D-Sander and D-Silter are normally not removed from the main assembly.
Secure lifting straps to manifolds BEFORE disassembling. Unbolt D-Sander from D-Silter assembly. Unbolt
D-Sander legs from main assembly. Use lifting straps.
Weight: Approximately 417 kg (920 lbs.)
D-Sander
2-12 Bolted to
D-Silter
Bolted To Main
Assembly
Secure lifting straps to manifolds BEFORE disassembling. Unbolt D-Sander from D-Silter assembly. Unbolt
D-Sander legs from main assembly. Use lifting straps.
Weight: Approximately 602 kg (1324 lbs.)
Bolted to
D-Silter
D-Sander
3-12
Bolted To Main
Assembly
Continued . . .
Lifting
Component
Method
NOTE: The D-Sander and D-Silter are normally not removed from the main assembly.
Secure lifting straps to manifolds BEFORE disassembling. Unbolt D-Sander from D-Silter. Unbolt and
remove rear D-Silter legs. Unbolt and remove front D-Silter legs. Use lifting straps around manifolds.
Weight: Approximately 612 kg (1350 lbs.)
Back Leg
Bolted to Front
D-Silter Leg
D-Silter
8T4
Back Leg
Bolted To Feeder
Front Leg
Bolted to Main
Assembly
Back Leg
Bolted to Skid
Secure lifting straps to manifolds BEFORE disassembling. Unbolt D-Sander from D-Silter. Unbolt and
remove rear D-Silter legs. Unbolt and remove front D-Silter legs. Use lifting straps around manifolds.
Weight: Approximately 823 kg (1811 lbs.)
Back Leg
Bolted to Front
D-Silter Leg
D-Silter
10T4 Front Leg
Bolted to Main Back Leg
Assembly Bolted To
Feeder
Back Leg
Bolted To Skid
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Equipment can be stored (upon arrival) in the shipping crate for a 12 to 24 month preservation period. When in
storage, do not expose equipment to dust, vibration or extreme weather conditions (such as heavy rain). If unit is
removed from original shipping crate, cover with a tarpaulin during any preservation period.
If shaker is stored after commissioning, take certain steps to ensure unit is stored in a way that protects the
equipment.
When disconnecting power connections to control station and motors, plug all inlets with an appropriate
fitting to keep water/moisture from entering. Do not leave any electrical connections open and exposed.
Using Hercules Real Tuff Thread Sealant with Teflon on plug threads helps to prevent leakage. In addition,
add anti-condensation packs to motor J-Boxes and control station. Install and seal all control station doors
and J-Box covers.
Figure 1.2
Sealant Used on Plug Threads
Replace items listed below after a 12 month preservation period. See the Recommend Spare Parts List in Section 7.0
for reference to Section / Item Number.
Follow normal commissioning procedures when re-commissioning shaker equipment. This information is found in
Sections 4.01 and 4.02. Verify all motors for proper rotation and requirement for greasing. Please refer to the
Martin Motor manual (“Storage” and “Lubricating Vibrator”) in Section 10.0 for more specific motor information.
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
TABLE OF CONTENTS
Page
Description
Number
Section 1.0 Operation 3-10
1.1 Functional Description of Equipment 3
1.2 Operating Instructions 3-8
1.2.1 Adjustable Parameters 3
1.2.2 Screen Selection 3
1.2.3 Flow Rate 4
1.2.4 Basket Angle 4-5
1.2.5 Shaker Speed 5
1.2.6 Three (3) Motor Control Panels 5
1.2.7 Bypass Operation 5
1.2.8 Start-Up 6
1.2.9 Controlled Shutdown 7
1.2.10 Emergency Shutdown 7
1.3 Screen Handling 8
1.3.1 Screen Installation Procedure 8-9
1.3.2 Screen Washing and Blinding 9
1.3.3 Screen Storage 10
The basic function of the Mongoose PT Platform Shale Shaker is to provide primary solids removal from
both oil based mud (OBM) and water based mud (WBM) during drilling operations.
When shaker is running under normal conditions, certain adjustable parameters optimize
performance:
Screen Selection
Flow Rate
Basket Angle
Selection of screen mesh depends on a number of factors: flow rate, fluid condition, formation,
rate of penetration (ROP), fluid type and number of shakers. Use the finest screen possible to
ensure optimum performance to the relative screen life.
A variety of screen meshes are available for the Mongoose PT Platform Shale Shaker. Review
Table 1 or contact your local M-I SWACO representative for more information.
Adjust flowrate to maintain a constant pool level on all shakers used. The optimal fluid end point
is 25-35 cm (l0"-14") from discharge end of front screen. Flow to each shaker is controlled by
vertically adjusting slide gates for each feeder.
The basket deck angle is manually adjustable between -3 degrees and +3 degrees. Shut down of
shaker before changing deck angle is not necessary.
Figure 1
Manual Jacks on Discharge End of Shaker
b. Use a manual ratchet, wrench or screen clamping wedge to adjust the 1-1/4” nut located on
top of jack. Adjust each side to desired position. (Refer to Figures 2 and 3.)
Figure 2 Figure 3
Wedging Clamp Wedge Block
NOTE: Do NOT adjust more than 2 degrees per side while changing deck angle.
NOTE: Always operate shaker with lowest possible basket angle to meet capacity
requirements. A steep incline results in screen overload and premature failure.
The Mongoose PT Platform Shale Shaker is designed to operate at 1,500 rpm (with 50Hz motor)
or 1,800 rpm (with 60Hz motor) in both water and oil based mud.
The three (3) motor control panels have a selector switch to operate the unit as either a linear
motion or an elliptical motion shaker. Linear motion operation is used for faster solids movement
across screens resulting in lower screen life.
Elliptical operation is used for slower solids movement across screens leading to longer screen life.
The unit can be switched from linear or elliptical on-the-fly (meaning operation does not have to
stop to switch between the two). Operation of linear or elliptical modes depends on operating
environments. (Refer to Figure 5.)
Selector Switch
Linear/Elliptical
START
(Left Side)
Lin. Ell.
STOP
(Right Side)
Figure 5
Control Panel
The flow line bypass is used to redirect fluid flow from the mud cleaner. Use the slide
gate to manually open or close the bypass. When bypass is closed, fluid from mud
cleaner flows to the shaker basket for further processing. The bypass is open when the
slide gate is pulled out. When the bypass os open, fluid flow is redirected.
D-Silter D-Sander
6” Ø (Victaulic)
D-Sander/D-Silter
Bypass
Figure 6
Flow Line Bypass
D-Silter
Slide Gate
Figure 7
Slide Gate
NOTE: Use steam or a water sprayer for water based mud. Use fluid compatible with the
specific drilling fluid for oil based mud.
c. Ensure a gate is placed at any unused outlet (of the skid) and desired outlet is unobstructed.
d. Check all electrical connections. Turn unit control panel to LINEAR or ELLIPTICAL (if unit
has a 3 motor) depending on drilling parameters.
g. Do not allow fluid end point to exceed 3/4 coverage of the discharge screen of each basket.
c. Thoroughly clean baskets and screens using appropriate medium. Use steam or a water
sprayer for water based mud. Use fluid compatible with the specific drilling fluid for oil
based mud.
NOTE: Do NOT use a squeegee or any other foreign object to clean screens.
NOTE: If unit is out of use for long periods, remove, clean thoroughly, dry and either re-box
or store all screens in a safe, dry area.
In the event an emergency shutdown is required, for whatever reason, follow the procedures listed
below:
d. After problem is resolved and area is safe, follow the proper start-up procedure (Section 5.01,
1.2.8) to re-start unit.
The Mongoose PT Platform Shale Shaker is designed for pretensioned screens with a wedge
mounting system. There are four (4) pretensioned screens and eight (8) wedges per Mongoose
shaker basket. Screens are placed on the screen bed and then wedges are driven between each
screen edge and support bars on shaker sidewalls. The screen bed is slightly crowned at the center
causing screen frames to bow when wedges are forced in place. This prevents screens from
“whipping” up and down during shaker operation. See screen changing/installation steps below.
b. While shaker is running, wash down screens. Clean all cuttings and solids build up around
inside of deck and wedges.
NOTE: Follow proper lockout/tagout procedures for turning off power to shaker.
d. Each screen is secured in place by two (2) wedges (one per side). A rubber mallet is required
to remove wedges. A rubber mallet blow to the end or the top handle section removes
wedges.
e. Remove screen panel. Screen panels are removed and installed one at a time.
NOTE: Steps f through i instructions apply to a single screen panel and must be repeated for
each additional panel.
f. Note wedges for second screen from feed end are reversed for easier installation.
g. Wash down screen bed and gasket prior to installing new screens. Replace any deck gaskets if
worn, cracked or hardened (See “Maintenance Procedures” in Section 6.0 of this manual).
Figure 9
Location of Wedges
i. Wet down new screens PRIOR to actual use of drilling fluids. Use steam or a water
sprayer for water based mud. Use fluid compatible with the specific drilling fluid for oil
based mud.
Wash screens with appropriate medium BEFORE shaker unit is shut down avoiding plugging or
blinding of meshes by dried solids.
1.3.2.1 If screen openings plug (blind) with drilled solids, see recommended methods below for
cleaning screens:
b. Wash screens from back side with water or diesel fuel with screens removed from unit
(depending on type of drilling fluid being screened).
Store screens in their cardboard containers. Horizontal or vertical stacking is permissible. Avoid
mechanical damage. Always wash screens prior to storing them.
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
TABLE OF CONTENTS
Page
Description
Number
Section 1.0 General Maintenance and Inspection 3-6
1.1 Safety Related Procedures 3
1.2 Routine Maintenance and Inspection 3-4
1.2.1 Daily Maintenance Procedures 3
1.2.2 Maintenance Procedures Schedule for Every 3000 Hours of Shaker Run Time 4
1.3 Preventative Maintenance Procedures 4-6
1.3.1 Motor Bolt Torque 4
1.3.2 Motor-Electrical Connections (Isolators) 5
1.3.3 Isolation Springs 5
1.3.4 Deck Adjustment Jack Greasing 6
Section 2.0 Maintenance Procedures 7-10
2.1 Screen Seal 7
2.1.1 Deck Seal Replacement Procedures 7
2.2 Springs 7
2.3 Vibrator System 7-9
2.3.1 Vibrator Removal and Installation 7-9
2.4 Cable Gland Assembly Instructions
2.5 Shaker Wash Down Procedures 9
2.5.1 Normal Daily Wash Down Procedures 9
2.5.2 Oil Base Mud Wash Down Procedures 9
2.5.3 Wash Down After Circulation of Completion Fluids 9
2.6 Surface Corrosion Removal Procedures 9-11
2.6.1 Cleaning Specifications 9-11
2.6.1.a Method A 10
2.6.1.b Method B 10-11
2.6.2 Coating Specifications 11
2.7 Decommissioning Procedures 11
Section 3.0 Troubleshooting 12
3.1 Electrical 12
3.2 Mechanical 12
Go through the list below covering general and safety related procedures BEFORE any maintenance is
carried out:
a. Have a certified electrician ensure power supplies are isolated BEFORE performing any maintenance
on unit.
c. Block up and secure heavy parts BEFORE working beneath unit or parts.
f. Ensure all tools, old parts, nuts, bolts, washers, etc. are removed BEFORE restarting unit after
maintenance.
The Mongoose PT Platform Shale Shaker is designed to minimize downtime by reducing routine
maintenance. Prolong equipment life by following maintenance instructions provided in this section at
established specified intervals.
NOTE: Use and complete the daily maintenance form at the end of this section and keep in your
maintenance records. MI-SWACO recommends making multiple copies of the form for future use.
a. Visually examine unit for signs of wear and/or damage. Repair/replace as necessary.
NOTE: Use and complete the 3000 hour maintenance form at the end of this section and keep in your
maintenance records. M-I SWACO recommends making multiple copies of the form for future use.
b. Check motor bolt torque (See “Preventative Maintenance Procedures” on page 7 for more
information).
c. Grease both jacks for deck adjustment system (See “Deck Adjustment Jack Greasing” on page 9
for more information).
After four (4) hours of running check and torque motor bolts again. This also applies to new installs in
the field. New bolts must be used. In the field, check torque monthly (700 hrs of continuous running).
Motor Bolt
Figure 1
Motor Bolts
The electrical box on each of the motors must have the factory supplied black neoprene vibration
isolators installed before shakers are run. (Refer to Figure 2.) Isolators are removable, but should
always be in place when unit is in use to protect electrical connections in the motor. Failure to do so
causes premature wiring failure or mounting post breakage.
Figure 2
Motor
(Electrical Connections with Isolators)
There are four (4) isolation springs per basket. Check each for signs of fatigue or fracture every 3
months, or if shaker basket is tilting side-to-side and cuttings are running to one side of the basket.
Fatigue of springs causes poor performance. Fracture of springs causes abnormal shaking and, if not
corrected, causes structural damage to the basket.
The springs are covered with a protective black nitrile “boot” serving as a safety precaution against
bare springs acting as a possible pinch-point. One way to check for spring fatigue is to set the basket
level and measure the height of each spring. The front two springs should be the same height, and the
back two springs should be the same height.
NOTE: The height of the back springs may differ from the height of the front springs.
First, remove all weight from springs BEFORE changing them. Lift basket (with proper lifting device)
to remove weight from springs. Once basket is lifted, remove top and bottom bolts securing spring.
The spring slides out for replacement.
Top
Bolt Spring (Behind
Shipping
Bracket)
Shipping
Bracket
Figure 3
Isolation Spring
(Discharge End of Basket)
The deck angle adjustment jacks have a grease fitting located on the discharge side of the jack. (Refer
to Figure 4.) Once a month, apply 10 shots of a multi-purpose grease into grease fitting and run deck
angle adjustment up and down twice to allow grease penetration to jack inner screw.
GREASE
FITTING FOR
JACK
Figure 4
Grease Fitting for Deck Angle Adjustment
e. Remove hardware and then remove rubber seals (gaskets) with bars.
f. Ensure screen bed area is clean. Remove and replace all grommets.
g. Install new seals and bars with hardware. (Refer to Figure 5.)
Figure 5
Deck Seals (Gaskets) and Bars
2.2 Springs
Replacing the four (4) main basket support springs on a bi-annual basis is recommended. If one spring
appears more compressed than the others, replace right away.
NOTE: For any maintenance to vibrator, refer to Martin Motomagnetic Operators Manual. Installation of
vibrator should be done by a certified electrician
a. Ensure power to control panel is switched off and locked out. These actions must be
performed by a certified electrician.
b. Disconnect cable gland from vibrator. (Refer to Figure 6.) Tag terminals for reinstallation.
Figure 6
Cable Glands
d. Remove the four bolts and washers holding vibrator in place (M20 Grade 10.9 bolts for large
motors, M16 Grade 10.9 bolts for small motors on 3 motor units).
e. Ensure vibrator mounting area is absolutely clean and not damaged BEFORE installing a
vibrator.
f. Clean bottom of vibrator feet. (Refer to Figure 7.) Ensure motor plate is also clean. (Refer to
Figure 8.)
Figure 7 Figure 8
Vibrator Feet Motor Plate
h. Secure vibrator using the four bolts, nuts and special flat washers.
CAUTION: Re-torque vibrator bolts after four (4) hours of running time.
Check torque monthly
A E
B C D F
Figure 9
Cable Gland Component Identification
5/8”
Figure 10
Armor Braid and Inner Jacket Cut to Size
f. Install entry item into motor J-Box entry and/or control panel entry and tighten.
g. Slide back nut, gland body and armor sleeve on motor cable.
j. Hold bronze armor braid located between armor cone and armor sleeve.
k. Insert armor cone and sleeve assembly fully into entry item and hold.
l. Slide gland body to entry item tightening and crimping armor between the armor cone and sleeve. (Refer to
Figure 11.)
Bronze
Braid
Figure 11
Armor Braid Locked to Gland Assembly
o. Thoroughly mix the two part epoxy compound in equal proportions to a uniform color and pliable
consistency.
NOTE: Plastic gloves are provided for protection while handling the epoxy compound.
p. Separate conductors and pack each in the mixed epoxy compound until all voids between conductors and
armor cone and sleeve assembly are filled. (Refer to Figure 12.)
Figure 12
Epoxy Compound Packed Around Conductors
q. Bring conductors back together and form a packing 1-¼” long and sufficient in size to fill compound tube.
(Refer to Figure 13.)
Figure 13
Epoxy Compound Formed to Fill Compound Tube
Figure 14
Compound Tube Filled with Epoxy Compound
s. Do not allow epoxy compound to exceed end of compound tube. Ensure epoxy compound is found at all
points between conductors and compound tube.
t. Insert conductors into entry item sliding cable gland assembly into position. Tighten gland body to the
entry item. Tighten back nut to gland body.
NOTE: Leave assembly undisturbed for 24 hours allowing epoxy compound to set.
2.4 Shaker Wash Down Procedures (Use PPE per Section 1.06)
a. After drilling and mud circulating is completed, thoroughly hose down entire shaker using water
with screens in place and shaker running to completely remove all solids from screen surface.
b. Once clean, shut off power and remove all screens and set them aside. Continue washing shaker,
without running it. Clean screen bed area extremely well ensuring seal area is free of drilling mud
that can cause bypass around screen frame later.
NOTE: Do not use a pressure washer which can damage fine mesh screens.
a. Follow same procedure as above (Normal Daily Wash Down Procedure), but use a suitable fluid
that is compatible with the specified drilling fluid.
Completion fluids typically contain a higher amount of chlorides and are usually highly corrosive.
Therefore, it is extremely important that an extensive wash down is carried out after circulation of
completion fluids is finished.
a. First, follow the “Normal Daily Wash Down” procedures. However, it is also recommended that
the shaker basket be lifted to its highest uphill angle and the interior of the basket be washed
thoroughly. Wash screens separately.
Due to possible oxidation of metals, mild surface corrosion may occur on some shaker components.
This corrosion will not affect the long term life of the stainless steel components. See recommendation
methods “A” and “B” below. The method chosen greatly depends on environmental conditions.
2.5.1.a. Method A of Cleaning Specifications for Surface Corrosion Removal and Clear Coat Touch-
Up: Recommend using an acidic paste (or equivalent) to remove surface corrosion.
a. Use protective equipment while applying (per Section 1.03 or local and national codes
requirements).
b. Apply a thick layer of Derustit SS-3 or DERUSTIT Beizpaste 4020 with a brush using a
plastic container.
d. Rinse area thoroughly with water using a 2000-3000 psi pressure washer. If pressure
washer is not available, normal line pressure is sufficient with use of a stainless steel wire
brush.
f. Once all surface corrosion is removed, wipe areas that were effected with a rag and
surface cleaner (paint thinner is recommended) to removed oil, dirt and debris from areas.
h. Apply first coat of VpCI®-383 (or equivalent). Apply using conventional methods
(spray, brush, roll or dip). Let first coat dry for 15 minutes.
i. Apply second coat of VpCI®-383 (or equivalent). Allow second coat to dry for 15
minutes.
a. Use protective equipment while applying (per Section 1.03 or local and national codes
requirements).
b. Before applying cleaner remove any non stainless steel rivets and hoses with non stainless
steel plated connections. Replace with stainless steel rivets and hoses with stainless steel
connections after application.
c. Apply ZEP Stainless Steel cleaner to effected areas per manufacturer recommendations.
g. Once all surface corrosion is removed, wipe effected areas with a rag and surface cleaner
(paint thinner is recommended) to remove oil, dirt and debris from areas.
i. Apply first coat of VpCI®-383 (or equivalent). Apply coating using conventional methods
(spray, brush, roll or dip). Let first coat dry for 15 minutes.
j. Apply second coat of VpCI®-383 (or equivalent). Allow second coat to dry for 15 minutes.
The water based protective coating listed below is recommended to protect surface once corrosion is
removed.
VpCI®-383
VpCI®-386
Cortec Corporation
4119 White Bear Parkway, St. Paul, MN 55110 USA
Email: info@cortecvci.com
Internet: www.cortecvci.com
Follow the procedures below when removing unit from work area or storing unit:
a. Wash unit to remove any media from shaker basket, feeder and skid.
b. Remove screens.
3.2 Mechanical
Solids are migrating to one side One vibrator motor not running. Check vibrator motor and control panel.
of the basket or not discharging One vibrator rotating in wrong direction. Reverse rotation.
properly. Unit not level. Level unit.
Vibrator overheating (70 degrees Bearing out of grease. Service bearings (See Appendix-A).
over ambient). Bearing worn out. Replace motor.
Comments:
Mechanics Name
Signed
Comments:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
O 10.0 OVERFLOW
MOTION GENERATOR 0.60 HP 254
(VOLTAGE PER CUSTOMER
SPECIFICATIONS)
EXPLOSION-PROOF
1 REQUIRED
6 INCH (VICTAULIC)
D-SANDER, D-SIL TER
BYPASS
80. 5
2045
53.7
1365
VIE W A-A APPROXIMATEC. G.
18.3 113.3
465 2878
ISO VIE W
General Arrangement for 9672370
8INCH[203.2]
8T4 D- SIL TER MANIFOLD OVERFLOW
(D-SILTER)
A
6 INCH [152.4]
M ANIF OLD INLET
(D-SILTER)
2-12 D-SANDER
MO TION GENERATOR2 HP
(V OLTAGE PER CUSTOMER 3 MOTOR NI LET COVERP LATE
SPECIFICATIONS) STARTER BOX ACCESS COVERS BOLT UPFOR
EXPLOSION-PROOF 10IN. 150 LBFLANGE
2 REQUIRED (CANBE FITTEDFOR
90.0 8" [203] AND6" [154 ]
88.3 2285 INLET WELD ST UB)
2242 84.5
2145
174.
8825 O 10.0
254
62.2 61. 1
1580 1 552 53.0 [1346] @ +3v
1 .1 @ 0v
51297
O
8.0
37. 7 48.5 [1232]@ -3v 30 28.1 203
957 764. 1 71 3
APPROXIMATE C.G. 29 10" INLET 6" INLET
739 LOCATION 29.1 6.0
WEIR HEIGHT 739 LOCA TION O
152
8" INLET
LOC ATION
BI L OF MAT ER I AL
UNLESS OT HE RW ISE SPE CIFI ED: SIG NATURES DATE
D I
M E
N S I
O N S A R E
I N N C H E
I S
M I
L I
M E T
E R S A R E
I N R A C K
B E T S DRAWN TR Ja n-09 -2 00 6
D E
R O O
M N E
V T B
S U
C R
L S
A E I N S
R
P
D
N
A T H
S R P E D G E
A S
NOTES: S U
R F
T L
A C
O E
E
R N
R O
U G H N
S S
E
A C E S P E A
2 5
1 I C R O
M
R N S I Y 1 4
. 5 M
I N C H
E S M S
R CHEC KED M-I L.L .C .
T H
I D
R A N G E
L P R
J E C I
O T O N
5 95 0 N O R T H C
OU S E D R IV E , H
R OUS T ON
, T EX A S 7 7 0 72
T O
L E
R A N
C E S O N ENGI NEER
. X X = + / - . 0 3
0 - 3 0 N
0 I C H E
S = + / - 1
/ 3 2
1 . SEEUSERS MAN UAL FORELECTRICAL CONTROL PANEL INFORMATION. . X = + / - . 0 6
0 3 0
- 6 0 I
N C H S
E = + / - 1
/ 1 6
. X = + / - . 1 0 6 0 & E R
V
O = + / - /
1 8
3
4
RE VIS I ON S
R EV DE SC RI PT IO N D RA FTE R C HK D AP PR VD DA TE
O 8.0 INLET
203
6 INCH(VICTA ULIC)
D-SANDER, D- SILTER
BYPASS
.0
171803
40. 4
10 26
54.3
1378
APPROXIMATE CG
1468.35 113. 3
VIEW A-A 2878
ISO VIEW
8INCH [203.2]
1:20
6T4 D- SILTER M ANIFOLDOVERFLOW
(D- SILTER)
6 INCH [152.4 ] A
MANIFOLD INLET
(D-SILTER)
2-12 D- SANDER
MO TION GENERATOR2 HP
(VOLTAGE PER CUST OMER
SPECIFICATIONS)
EXPLOSION-PRO OF
2 REQUIRED 3 MOTOR NI LET COVER PLA TE
STARTER BOX BOLT UP FOR
10 IN. 1 50LBFLANGE
(CAN BEFITTEDFOR
8" [203] AND 6" [154]
88.3 90.0 INLET WELDSTUB)
2242 84.5 2285
2145
74.2 10. 0
1885 O 25 4
6 2.2 61 .1
1 580 1 552 53.0 [134 6]@ +3v
51. 1 @0v
1 297 30.1 O
8.0
48.5 [123 2]@ +3v 764 28. 203
37.1
942 10" INLET 7131
APPROXIMA TECG 29 LOCATION 6" INLET
739 2 9.1 LOCATION O
6.0
WEIR HEIGHT 73 9 152
8" INLET
LOCATION
. X X X
= + /
- . 0 3
0 0 -
3 0 N C
I H E S = + /
- 1 / 3 2
EN GIN ER
. X X = + /
- . 0 6
0 3 0 -
6 0 I C
N H E S = + -
/ 1 / 1 6
. X = + /
- . 1 0 6 0 & O V
E R = + /
- 1 / 8
NO TES: A N G L
S
E + /
- 0 ° 3
'
0 C H A
M & C '
S I N K
S + /
- 2 °
APPR OVED M ON GOO SE PT M U D C LEANER (LOW W EIR)
C O N FID E NT IA L
T H IS D R A W
I NG AN D /O R S P EC IF IC A TIO N E MB O
D IE S 2- 1 2 D- SAN DER, 6 T4 D- SILTE R
C O N FID E N TIA L I N FO R M AT IO N O F S W AC O , AD I V IS O N
1 . SEE USERS M ANUAL FOR ELECTRICAL CONT ROL PANEL INFORMATION. OF M - IL . L.C ., I N TH E AB S E N CE O F E XP R ES S W RIT T E N
PERM
IS IO N . S W A CO H AS L O A NE D T HI S C O PY W IT H T H E
2 . UNIT WEIGHT 5700LBS [2 585 Kg. ] APPROX. U N D ER S T AN D IN G T H A AT )( IT W I L N O T B E RE P R O
DUCED
GENER AL ARR ANGEM EN T DRAW ING
( )B TI W IL L N O T EB U SE D F O R A N Y P U R PO S E EX C E P T
THATO F R W H IC H I T W SA L O NA E D A ND ( C IT) W LI B E SHET SC
AL E S IZ E D R A WI N G N O . EV
R
3. DIMENSIONS IN BRACKETS ARE METRIC. R E TU R N E D O
N D EM A N DO R U PO N
T H E C O N TR A C TE D W O RK , W HI CH
CO M P LET IO N O F
E VE R C O
M E SF IR S T. 1 OF 1
Section 8.01
Document Title: General Arrangements
General Arrangement for 9672360
Section 8.01
R EV IS I ONS
1 4.4 64.7 1 8.2 R EV DES CR IP TI ON DR AFT ER CH K D AP PR VD D AT E
366 1645 4 62
8.0
O 203 INLET
MOTION GENERATOR 0.6 0 HP
(V OLTAGEPER CU STOM ER
SPECIFICATIONS) 1 0.0
EXPLOSION PROOF O 254 OVERFLO W
1 REQUIREDPER SHAKER
80. 5
2045
52. 7
1338
APPROXIMATE C.G .
113. 3
2878
VIEW A-A
18. 3
465
ISO VIEW
1:20
97.3
2472
82.9 END CONES PLUGGED
2107 1 0" [254] TO CREATE 6T4 D -SILTER
General Arrangement for 9672360-88
A
DECK ANGLE 31 .5
INDICATOR 800
33.5 33 .2 RECTANGULAR COVER
32 .2 OUTLET DOOR 63. 0
851 844 PLATE ATBYPASS 16 00
81 8 (2 REQUIRED)
APPROXIMATE C.G . RECTANGULAR TO PIP E
TRANSITION AVAIL ABLE
92. 9 64. 5
2359 163 8
68.9
1749
BIL LO F MATE RIAL
UN LESS OTH ERWI SES PEC IFI ED: SIG NATU RES D ATE
D IM E
N S IO N
S A R E IN I N
CHES
NOTES: M IL LIM E TE R S A R
E IN B R C K E TS
A
D RAWN JH F 03 -16 -0 7
DON OT S CA L EPR IN T S
REMOV E
BUR
S ANDSHA RPE DGE S
URF A
S CE ROUGHNE
S S 1 25 M IC R
O IN
CHE
S R MS C HECK ED M-I L. L.C .
TO L E R
ANCESPE
R A N S IY 14 .5 M
5 95 0 N O R
TH COU
RSEDRI V
E , H O U S TO N , T E X
AS 7 0 72
1. DIMENSIONS ARE IN INCHES [MM ]. ALL DIMENSIONS ARE NOM INAL UNLESSSPECIFIE D OTHERWIS E. TH IR D A N G
L EPR
OJ E
C T IO N ENGI NEER
TO L E R
ANCE S ON:
X. X X + /- 0. 0 5 F AR C + -/ 1 /3 2
2. APPROXIMATE DRYW EIGHT OF UNIT: 5705 LBS [2588 KG]. .X X + /- .0 1 5 A NG + / - 1 / 2 D EG A PPRO VED
3. SHAKER SHIPSW IT H A WELD PLATE THAT MAY BE REMOVE D TO USE A 10" 150 LB FLANGE .X + /- .0 3 1 C ON CE N . 0 0 5 D AI
MON GOO SE P T MUD CL EANER
C O N FID E N TI A L
INLET OR M ODIFIED BY THE CUSTOMER FOR OTHER INLET SIZ ES. TH IS D R A
W I N G A N D /O R SP
E IF IC A TI O N
C MB OD
E I ES 2-12 D-SAN DER, 6 T4 D-SILTER
O N
C F ID E NT IA LI N F ORM A TIO N O F S
W A C O , A D IV IS IO N
F M -I L .L .C ., IN TH E A B
O SENC E OF E X P R E S S WR I T TE N
4. SHAKER IS EQU IPPED WITH(4) O 1. 06 INCH M OUNTING HOLES TO BOLT SKID DOWN TO E R M IS IO N .S
P WA
COHA S L OA
N D T H IS C O P Y W
E I TH T H E GE NER AL AR RANG EMENT D R AWING
UNDE R S TA N D IN G T H
A T (A ) IT W IL LN O T B E R E
P ROD
U C
ED
PLATFORM. (B ) IT WI LN O T B E U S E D FO R A NY P URP OS EEXCE
PT
TH A T F O R WH IC H I T WA S L O A N
E D A N D (C ) IT WIL L B E SHEET S C A LE S I ZE R A W IN G N O .
D REV
E
R TU R N
E D ON D E MA
ND O R U P O N C O M P LE T IO N O F
5
6
RE VIS I ON S
R EV DE SC RI PT IO N D RA FTE R C HK D AP PR VD DA TE
18.2
462
MO TION GENERATOR 0.60 HP
(VOLTAGE PER CU ST OMER
SPECIF ICATIONS)
EXPLOSION- PROOF
1 REQUIRED
6 INCH(VICTA ULIC)
D-SANDER, D- SILTER
BYPASS
71. 0
1803
40. 4
10 26
148.
2387
APPROXIM ATE CG
1468.35
VIEW A-A 113 .3
2878
ISO VIEW
8INCH [203.2]
1:20
6T4 D-SILTER M ANIFOLDOVERFLOW
(D- SILTER)
6 INCH [152.4 ] A
MANIFOLD INLET
(D-SILTER)
BILL OF MAT ER I AL
UN LESS OT HE R WIS ES PECI FIE D: SI GNA TU RES DA TE
D I M N
E I O N
S S A R E
I N I C H E S
N
M I L I
E T E S
M R A R I
E N R A C K T
B E S DR AWN Jan-19-2 00 6
D O T
O
N S C
A L E I N T S
R
P
T R ose
R E M V
O
E B U
R R S A
D
N S H
A R P E G E S
D
S U R F
C E
A R U G H N
O S S
E 1 5
2 M I
C R O I N
C H E S R M S CH ECKED M- I L.L .C.
T O L E
A N C E
R S P E R
A N S I Y 1 4 .
5 M
T H I D
R A N G
L E P R
J E C T
O I O N 5 95 0 N
O T H C O U R S E D R IV E , H
R O U S T O N ,T E XA S 7 0 7 2
T O L E
A N C S
R E O N
. X X X
= + /
- . 0 3
0 0 -
3 0 N C
I H E S = + /
- 1 / 3 2
EN GIN ER
. X X = + /
- . 0 6
0 3 0 -
6 0 I C
N H E S = + -
/ 1 / 1 6
. X = + /
- . 1 0 6 0 & O V
E R = + /
- 1 / 8
NO TES: A N G L
S
E + /
- 0 ° 3
'
0 C H A
M & C '
S I N K
S + /
- 2 °
APPR OVED M ON GOO SE PT M U D C LEANER (LOW W EIR)
C O N FID E NT IA L
T H IS D R A W
I NG AN D /O R S P EC IF IC A TIO N E MB O
D IE S 6T 4 D -SILT ER
C O N FID E N TIA L I N FO R M AT IO N O F S W AC O , AD I V IS O N
1 . SEE USERS M ANUAL FOR ELECTRICAL CONT ROL PANEL INFORMATION. OF M - IL . L.C ., I N TH E AB S E N CE O F E XP R ES S W RIT T E N
PERM
IS IO N . S W A CO H AS L O A NE D T HI S C O PY W IT H T H E
2 . UNIT WEIGHT 4700LBS [2130 Kg.] APPROX. U N D ER S T AN D IN G T H A AT )( IT W I L N O T B E RE P R O
DUCED
GENER AL ARR ANGEM EN T DRAW ING
( )B TI W IL L N O T EB U SE D F O R A N Y P U R PO S E EX C E P T
THATO F R W H IC H I T W SA L O NA E D A ND ( C IT) W LI B E SHET SC
AL E S IZ E D R A WI N G N O . EV
R
3. DIMENSIONS IN BRACKETS ARE METRIC. R E TU R N E D O
N D EM A N DO R U PO N
T H E C O N TR A C TE D W O RK , W HI CH
CO M P LET IO N O F
E VE R C O
M E SF IR S T. 1 OF 1
Section 8.01
Document Title: General Arrangements
General Arrangement for 9672365
Section 8.01
RE V ISI ON S
M OTION GENERATOR 0. 60 HP
(VOLTAGE PERC USTOMER
SPECIFICATIONS) O
10. 0 INLET
25 4
EXPLOSION-PRO OF
1 REQUIRED
O 12. 0 OVERFLOW
305
6" (VITAULIC)
D-SAN DER, D -SIL TER
50. 3
1278
APPROXIMATE C .G.
1 13. 3
2 878
18.
VIEW A-A
4635
General Arrangement for 9672385
ISO VIEW
10T4 D-SILTER 10" [ 254]
1:20
M ANIFOLD OVERFLOW A
(D-SILTER)
8" [203.2 ]
MANIF OLDINLET
3 -12 D-SANDER (D-SILTER)
MO TIO N GENERATOR 2 HP
(VOLTAGE PER CU STOMER
SPECIFICATI ONS)
EXPLO SION-PR OOF 3 MOTOR
2 REQUIRED STARTER BOX ACCESS COVERS INLETC OVER PLATE
90.8 BOLT UP FOR
2307 97. 6 1 0" 150LBFL ANGE
90.8 2 480 (CAN BEFITTED FOR
63.4 2307 8" [2 03]AND 6" [1 54]
1610 INLETWELD S TUB
78. 1
62.6 1 983 1 0.0
1589 O
2 54
53.0 [1 346] @+3v
51.1 @0v
4 2.8 1297 29.9 O 8.0
1 087 48.5 [1 232] @-3 v 760 203
APPROXIMATE C.G. 10" INLET
29 LOC ATION 28. 27.9 O
6. 0
73 5 7359 709 1 52
WEIR HEIGHT 8" INLET 6" INLET
LOC ATION LOCATION
U ND E R S TA N D IN G T H A AT )( IT W I L N O T B E R EP R O D U CE D
GENE RAL ARR ANG EME NT DRA WING
(B ) IT W IL N O TB E U SE D F O RA N Y PU R P O S E E X C EP T
S H E ET S C A LE S IZ E D R A WI N G N O . REV
TH A T F O R W H IC H IT W AS L O AN E D A ND ( C ) IT W I L B E
R ET U R N ED O N D E M A N DO R U PO N C O M P L ETI O N O F
TH E C O NT R A C TED W O R K , W HI CH E V ER C O M E S F IR ST . 1 OF 1
7
8
R EV IS IO N S
REV D ES CR IP TI ON DA T E
DR AFT ER CH KD A P PR VD
1 4.4 6 4.4 1 8.2
3 66 1 636 46 2
40.2
1022
50.4
1281
APPRO XIMATE C.G.
1 13.3
2878
1 8.3
VIEW A-A
4 65
ISO VIEW
1:20
1 0" [254]
MANIF OLD OVERFLOW
(D- SILTER) A
8T4 D-SILTER
MO TION GENERATOR 2 HP
(VO LT AGE PER CUSTO MER
SPECIFICATIONS) 3 M OT OR
EXPLOSION- PR OOF STARTER BOX
2REQUIRED ACCESS CO VERS INLET CO VER PLATE
9 0.8 BOLT UP FOR
2 307 10" 1 50LB FLANGE
6 3.4 90.0 (CAN BE FITTED FOR
1 610 84.5 2285 8" [203 ]AND6" [ 154]
2145 INLET WELD STUB
62. 6 74.2 0
1589 18 85 O 120.54
53. 0 [1 346] @+ 3v
51.1
1297 @0v 2 9.9 O 8.0
39. 48. 5[1 232] @-3 v 76 0 203
10108 10" INLET
APPROXIMATE C.G . 29 LOC ATION 28. 27. 9 O 6. 0
73 9 7359 709 15 2
WEIR HEIGHT 8" INLET 6" INLET
LOCATION LOCATI ON
FIL E NA M E: Swa c o D Ma c h i ne d
ACKNOW LEDGED:_ _ _ _ _ _ _ _ DATE:_ _ _ _ _ _ _ _ _ N EXT ASSY TO P AS SY 1 :15 D 9050341 -
General Arrangement for 9672380
Section 8.01
Document Title: General Arrangements
Section 8.01
RE VIS IO N S
O 10.0 INLET
254
OPTIONALEXTRACTION PORT
O 12.0 OVERFLOW
305
40. 2
102 2
55. 2
14 02
APPROXIMATE C.G .
6" (VICTAULIC) VIEW A-A
D-SANDER, D-SIL TER 1 8.3 120. 0
BYPASS 4 65 3048
General Arrangement for 9672875
LESS D-SILTER VENT HOOD FOR REFERENCE ISO VIEW 1 0" [254]
D- SILTERVENT HO OD 1:2 0 M ANIFOLD OVERFLOW
FUM EEXTRACTION PORT 1:20 (D-SILTER)
FEED END SCREEN 10IN FLANGE CONNECTION
ACCESS DOOR
A
BASKET VENT HO OD C OVER
8" [203.2]
MANIF OLD INLET
3-1 2 D-SANDER (D- SILTER)
BASKET VENT HO OD
MOTION GENERATOR 2 HP SCREEN WEDGE ACCESS DOOR
(VOLTAGE PER CUST OMER (2) PLCS.
SPECIFICATIONS) 3 MOTOR
EXPLOSION- PROOF
2 REQUIRED S TARTERB OX
ACCESS COVERS INLET COVER PLATE
90. 8 103.5 BOLT UPFOR
230 7 2628 10" 1 50LB FLANG E
92.1 (CANBE FITTED FOR
63. 4 2340 8" [203 ]AND 6" [1 54]
161 0 INLET WELD S TUB
78.1
62.6 1983 10. 0
1589 O 25 4
5 3.0 [1346]@ +3v
51.1
4 5.0 1297 @ 0v 29.9 O 8. 0
1 144 48. 5[1 232]@ -3v 760 2 03
APPROXIMATE C. G. 10" INLET
9
2735 LOC ATION 28.9 27 .9 O 6. 0
735 709 152
WEIR HEIGHT 8" INLET 6"INLET
LOC ATION LOCATI ON
(UNDE STA
B) ITRWI DINGTHAT(
L LNNOTB E USEA)DFIT WIO L NO
RANYPUR
T BEPROSEE EPROXDCEP
UCETD GENERAL AR RANGEMENT DRAWING
HEET
S SCAL E I ZE
S RA WINGNO.
D REV
THATF ORWHI
RETURNEDO NCDHIEMTWA
ANDSORL OA UPNOEDA
N NCOD(MPC)L ITETIOWIL BE
NOF 9 672 8 75
THECONTRACTEDW ORK, WHI CH EVERCOM ESFIRST. 1 OF 1
F IL ENAM E: Sw a co D Ma c h i n ed
ACKNOW LEDGED:_ _ _ _ _ _ _ _ _ DATE: _ _ _ _ _ _ _ _ N EXT AS SY T O PASSY 1: 15 D 90 5035 3 -
9
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Section 8.02
REV D E SCR I PTI O N D R AFT ER C HK D AP PR V D DA T E
LEGE ND
M OT OR
S HAK ER
DIV E RT ER GA TE
M UD SU PP LY PU MP ED
FROM TA N K
MU D SU PP LY PU MP ED
FROM TA N K
SO LI DS
SHAKER
ASSEMBLY
MU D SU PP LY FLOW
LIN E C ON N EC TION
SHA K ER BAS K ET
S HA KE R
M TR3
M TR 1
M TR 2 M UD GU TTER
3 MOTOR S TART ER
BILL O FM ATER I AL
UN LESS OTHE RWIS ES PEC IFI ED : SI G NA TURE S DA TE
D IM E NS IO N S A
R E IN I N C
HES
M IL LI M
ETER S A R E IN B R
A C K E TS DR AWN
DON
OT S CA
L E P R IN TS
GAR 03/1 6/05
REMOV E B U R
SANDSA
HPED
R GE S
S U R FA
CE O
RUGHNE
S S
1 2 5 IM C
R O IN C H
E S R MS CH ECK ED BSC 03/1 7/05 M-I L. L.C .
TO
LER
ANCE
SPERAN
S IY 1 4. 5M
59 5 0 N O R
T H C O U R S E D R I VE , H O U S T O N
, T E XA S7072
3 MOTOR TO
LH E
.X X
IR R
DNC
A GELO
S
X + /-
PN
R :O JE C TIO N
. 0 05 F RA C +/ - 1/ 32
EN GIN EER
.X X + /- . 0 15 A NG +/ - 1 /2 D EG MongoosePTPlat form
a chi ned
.X + /- . 0 31 C ON CE N . 0 05 D IA APP ROV ED BSC 03/1 7/05
C O N FID E N TIA L
T HI S D R A WIN G A ND / O R SP E C IF IC AT IO N E M B O D IES Mud Cleaner
C O N FID E N TI AL I N FO RM A T IO N O F S WA C O , AD I V IS IO N
OF M - IL . L. C. ,I N T H E A B S EN C E O F E XP R ES S WR IT E N
PERM IS IO N . S WA C O H A S LO A N E D T HIS C O PY WI T H TH E
U N D ER S T A ND IN G T HA T (A ) IT WIL L NO T B E RE P R O D UC E D
Piping &I nst rumentat ion Di agram
B( ) IT WI L N O T B E U S E D F O R A N Y P U R PO S E E X CE P T
SH E E T S C AL E SI Z E D R A WI N G N O . R EV
T H A T FO R WH I CH IT W AS LO A N E D AN D ( C )I T WIL L BE
R E TU R N E D O
N D E M AN D O R U P O N CO M P LET IO N O F 9672370, 9672360 &
T H E C O N TR A C TE D W O R K ,W H IC H EV E R C O M E S FI RS T . -
3
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
R EV D E SC RI PT IO N D R AFT ER C HK D A P PR VD D A TE
Section 8.03
INLET
D-SIL TER
SOLIDS
T
EN
FFLU
E
HYDROCLON E BYPASS
(SOLIDS DISCHARGE)
SOLIDS DISCHARGE
FROM SCREEN DECK
.X X + /- . 05 FR A C +/- 1 /3 2
.X + /- . 015 AN G + / - 1 / 2 DE G
.X + /- . 031 CO N C EN .0 0 5 DI A
APPR OVED
C O N FI D E N TI A L MONG OO SE P LATFO RM MU D C L EANER
T H IS D R A W IN G A N D /O R S P EC I FIC A T IO N E M BO D IE S
C O N FI DE N T IA L IN F O R M AT IO N O FS W A CO , A D I VIS I O
N
O F M -IL . L .C ., IN TH E AB S E N CE O F E XPR ES S W RIT T E N
P E R SM I O N. SW A C O H AS L O A NE D T H IS CO P Y W IT H T H E
MU D FLOW DIAG RAM
U N D ER S T A N DI NG T H A AT )( IT W I L N O T BE R E P RO D U C E D
( )B IT W I L N O TBE U SE D F O RA N Y P UR P O S E X C E P T
T H A T F RO W HI HC IT W AS L O NA E D A N D (C ) IT W IL B E S H E ET SCAL E S I ZE D R A WI N G N O . EV
R
R E T UR N E D O N D E M A ND O R U PO N CO M
P L ET IO N O F 9672370,9672360&
3
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Section 8.04
R EV DE SC RI PTI ON DR AFT ER CH KD APP RV D DA TE
BACK/FEED END 2
OF UNIT LOADINGS LOADINGS
(lbs; kg) (lbs; kg )
1
LOAD LOAD
DRY OPERATING DRY OPERATING
3 POINT POINT
9672370 9672360
ISO VIEW OF FOUNDATION VIEW POINTS 2-12, 8T4 MUD CLEANER 2-12, 6T4 MUD CLEANER
1 4 4 3 2 3
B ILLO FM AT ER IA L
93 93 UN LESS OTH ERWISE S PE CI FIE D: S IG NA TUR ES DA TE
EXISTING STRUC TURE 63 IM DRAWN
CHE CKED M - I L.L. C.
DSUREOLEMIM NESCVETO
CRNSRO S 5950N
ORTHCOURSEDRIVE, HOU
S TON, TE
XAS77072
THO LLFAO
DEXEABNG UEASLESRG
APEEHNO INBTSRCAHEY4KS5METIED.SCRGO
EN GIN EER
LEFT SIDE VIEW O F UNIT FRONT VIEW OF UNIT RIGHT SIDE VIEW OF UNIT .XOIR
CNFIDENTIAL
O
+/CL-ESPR .0N :EDJEA153SHCNATI12RPO
NESAFCINNROCGACCH+EES/-NR.M
1/0253DE2IGA APPR OVED MON GO OS E PLAT FOR M
TH ISDR AWI N G AN D /OR SPCIFEICATIONEM BODIES MU D CLEAN ER
ONFIDEN
C TIALI N FORM ATIONOFSWACO , ADVII SION
FRM
PEO MIS-I IO
L.N.
L.SC.W INTHEABSE
, ACO NCEO
HASLOANE DTH
FSCOIEXPREPYW SSW RTTE
ITHTH I NE
UNERS DTANDGINTHAT(A) ITWI LNOTBEREPRO D UC ED FO UND ATION PLAN
(B) ITWI LNOTBEUSEDFORANYPUR POSEEXCEPT SHEE T SCALE SI ZE DRAWI N
G NO. REV
ATFO
ETHTUR
R EDORWNDE
N HI MC
HANDO
IT WASRLOU
PANE
ON
D CO
ANM C
D(PLE
) TITIO
WNI LO
BEF
9672 370, 9672360,
3
4
Dr y Pr ope rties D ry P roper ties R EV IS IO N S
Da tum X ( in) D atum Y ( in ) F orc e ( lbs ) Dat um X ( m m ) D atum Y ( m m ) For c e (K N ) NO TES: REV DE SC R IP TIO N DR A FT ER CH KD A P PR VD D AT E
63.0
160 0
31 .0
78 7
APPROX C.G .
6 3.0
1 600
30.2
768
APPROXC .G.
ISO VIEW
1:20
L1
L4 58.9
149 5
INLET END APPROX C.G .
9 2.9
2 359
L2
OPERATING PROPERTIES
1:1 5
LOAD REACTION POINTS BIL LO FM ATERI AL
1:20 UN LE SS OT HE R WIS ES PEC IFI ED: SI GNA TU RES DA TE
DIME NSION
SAREININCHE S
MIL LIMETERSAREINBRAC KETS DRAW N JHF 7/16 /0 7
5 6.0 DO
RE M OTSC
NOVEB LE
ARSAN
U P D R
INSHA
TSRP EDGE S
SU FA
CEROUGHN ESS12 CR
OINCHE
SRMS CHEC KED M-I L. L.C .
1 423 TO RR
LE ANCESPE
RANS I Y145 .5MIM 5950NORTHC
OU R
SEDRI VE,HOUSTO
N, TEXAS 7 072
TH
TOIRR
LEDAN
ANCLEPRO
GESON
: JE CTION ENGI NEER
APPROX C.G . 9 2.9 .XXX +/- .005 RFAC+/- 1/32
.XX +/- .015 ANG+/-1/2DEG APPR OVED
2 35 9 .X +/- .031 CONCEN.005DIA MONGOOSE 3 MOTOR
CO NFID ENTIAL
THIS DRAWI NG AND/OR SPEC IFCATIO N EMBODIES W/VENT HOOD & MUD CLEANER
CO
OFM-NFIDIL.ENL.
TCIA.,LII NT
NFHORMA
E ABTSENC
ION EO
FOF
SW EX
ACPO,RADESI VIW
SRI
IOTNEN
DRY PRO PERTIES PERMISION. SWACO HASLOANEDTHISCOPYWI THTHE
UNDERSTANDINGTHAT( A) ITWI L NOTBEREPRODUCED FOU NDATION LOADING
(B) I TWIL NOTBE USED FO RANYPURPO SEEXCEPT SHEE T SCALE SIZE DRA WINGNO. REV
1:15 THTAURNE
RE T FODRWO NHIDEMAND
CHIT WO ASRLOA
UPO
NNEDAN
COMPLE
D( C)I TITW L BE
NI OF
O
THE CONTRACTED W O RK, WHICH EVERCOMESFIRST. PERS ALES ORDER
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
CL I E NT
P LA TF O RM C A BLE N O . 3 UL / N E MA E P
M O TO R
PL A T FO R M - 3 E N C L O S URE
N O .2
P LA TF O RM
C A BLE N O . 4
M O TO R PL A T FO RM - 4
N O .3
BI LLO FM ATERI AL
UN LESS OT HE RW IS ES PE CI FIE D: SI GNATU RES DATE
D IM E NS IO N S A
R E IN IN C H E
S MP R
M IL LI M
ETER S A R E INBRAC KETS DR AWN 10- 27- 03
DONOT S CA
L EPR
I N
TS
RE
MOV E B U
RSAND SHARP
E DGE
S GR
SURAFE O
C RGHE
U N S S 12 5 M IC
R O IN C H
E S R MS
CH ECKED L .L .C .
TO
L ER
ANCE
SPE
R N ASI Y 14 5. M 10-27- 03
59 5 0 N O R T H C
OU S E D R I VE , H O U
R S T O N , TE X A S 7 0 7 2
T H IR D A
NGL E P R O JE
C T IO N
TOL ER ANCE S ON: ENG IN ER
.X X + /- . 03 1 F RA C +/ - 1/ 32
A H
.X + /- . 03 1 A NG +/ - 1 /2 D EG
.X + /- . 03 1 C ON CE N . 0 05 D IA APPR OVED 10-2 7-0 3
MONGOOSE P LA TF ORM MUD CL E ANE R
C O N FI D E NT IA L
T H IS D R A W
I NG AN D /O R S PE C IF IC AT IO N E MB O
D IE S CABL E BL OCK DI A GRA M P E R
C O N FI DE N TIA L I N FO R M AT IO N O F S W A C O ,A D I V IS O
N
OF M - IL . L.C ., I N TH E AB S E NC E O F E XP R ES S W RIT T EN
PERM
IS IO N . S W A CO H AS L O AN E D T HIS CO
P Y W IT H T H E
U N D ER S T AN D IN G T H A T(A ) IT W I L NO T B ER E P RO D U C ED
( B) IT W IL L N O T BE U SE D F O R A N Y P U RP O S E EX C E PT SH E E T S C A LE SI Z E RA
D W IN G N O . R EV
T H A T FO R W H IC H I T W AS L O
A N E D AN D ( C) IT W IL B E
R E TU R N E D O
N D EM A N DO R UP O N
T H E C O N TR A C TE D W ORK, WH IC H
CO M PL ET IO N O F
EV E R CO M E SF IR S T.
9672370, 9672360 -
3
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
No. Number
1 Cover, Skid Bypass Opening, Mongoose 9672148 1
2 Cable Tower Weldment, Mongoose 9672149 1
3 Mongoose PT Unfinished Unit 9672160 1
4 Wiring Kit, 3 Motor, UL 50 ft. 9672307-01 1
5 D-Silter Assembly 8T4 Mongoose PT Mud Cleaner Platform 9672456 1
6 2-12 D-Sander Assembly Mongoose PT Mud Cleaner Platform 9672412 1
7 Flat Washer M12 Metric 304SS 05-305 36
8 Hex Nut M12 Metric 304SS M12 x 1.75 03-415 18
9 HHCS M12 x 40 Metric 304SS 04-1106 14
10 Lock Washer M12 Split 304SS 05-306 18
11 HHCS M12 x 45 Metric 304SS Hex Head Cap Screw 04-1270 4
12 Cover Plate, Cable Retainer Tower 9672155 1
13 Decal Arrow Rotation 9650367 6
Starter Kit, 3 Motor, UL, 575-600V, 60 Hz for Configurations
9672303-03 1
9672370-11 & 9672370-11L
Starter Kit, 3 Motor, UL, 380-415V, 50 Hz for Configurations
14 9672303-02 1
9672370-07 & 9672370-07L
Starter Kit, 3 Motor, UL, 440-480V, 60 Hz for Configurations
9672303-01 1
9672370-03 & 9672370-03L
Motor Vibrator, 2 HP, 575-600V, 60 Hz for Configurations
EM3C00037 2
9672370-11 & 9672370-11L
Motor Vibrator, 2 HP, 380-415V, 50 Hz for Configurations
15 EM3C00011 2
9672370-03 & 9672370-03L
Motor Vibrator, 2HP, 440-480V, 60 Hz for Configurations
EM3C00010 2
9672370-03 & 9672370-03L
Motor, 0.6 HP Elliptical Motion, 575V, 60 Hz for Configurations
EM3C00038 1
9672370-11 & 9672370-11L
Motor, 0.6 HP Elliptical Motion, 380V, 50 Hz for Configurations
16 6905003 1
9672370-07 & 9672370-07L
Motor, 0.6 HP Elliptical Motion, 480V, 60 Hz for Configurations
69120021
9672370-03 & 9672370-03L
97.3
82. 9
18.2
ISO VIEW
1:20
BOLT UP FOR
88. 3 9 0.0 10 IN. 150 LB FLANGE
84. 5
74. 2 16 SEE TABLE MOTOR, 0.6HP, ELLIPTICAL MOTION 1 -
15 SEE TABLE MOTOR, VIBRAT OR 2 -
62. 2 61. 1 14 SEE TABLE STAR TER K IT, MONGO OSE, 3- MOT OR 1 -
54.4 13 9650 367 DECAL ARROW ROTATION 6 -
12 9672 155 COVER PLA TE, CABLERETAINER TOWER 1 -
11 HHCS _M12X45MM HHCS M1 2 X45 mm LG 4 04-1 270
30.1 10 SPLITLOCK_M1 2 SPLIT LOCK W ASH ER M12 REGULAR 18 05-30 6
9 HHCS _M12X40MM HHCS M1 2 X40 mm LG 14 04-1 106
8 HEXNUT_M 12 HEXNU T M 12 18 03-41 5
7 FLATWSHR_M12 FLAT W ASHER M12 REGULAR 36 05-30 5
M I L I
M E
T E R S R E I N
A R A C K E
B T S DRAW N N ov- 29- 20 05
D E
R O M O
N E
V T B
S U
C R
A R
L S
E A
P N
I N S
R
D T H
S R P
A D G E S
E
JA M
S U R F
A C
E R O U G
H N E
S S 2 5
1 M I
C R O I N C H
E S R M
S CHECKE D M-I L.L .C.
T O L E
R A
N C E S E R A N S I Y 1 4 .
P 5 M
T H I R
D A N G L E P R O
J E C T
I O N
T O L E
R A
N C E S N
O 595 0N
O RTH C
OU RSE DRIVE, H
OUSTON, TEX AS77072
. X X X = + / - 0 3 0
. 0 -
3 0 N C H E
I S = / - 1 / 3 2
+
ENGI NEER
. X X = + / - 0 0
1
. 6 0 3 0 &
6 6 0 O V
- N R
I
E C H E
S = / - 1 / 8
+ 1 6
A N G L
E S + / - ° 3 0
0 ' C H A
M & C ' S I
N K S / - 2 °
+
APPROVED FINA L A SS EMBL Y 2 -12 8T4
9672370-11 & 9672370-11L 9672303-03 STA RTE R KIT, 3 MOTOR, UL, 575-600V, 60HZ E M3C00037 M OTOR, 2HP, 575-600V , 60HZ EM3C00038 MOTOR, 57 5V , 60HZ C O N FI D E N T IA L
T H IS DR A W IN G A N D /O R S P EC I FIC A T IO N E M BO D IE S MO DEL : MON GO OS E P T PLA T FO RM
9672370-07 & 9672370-07L 9672303-02 STA RTE R KIT, 3 MOTOR, UL, 380-415V, 50HZ E M3C00011 M OTOR, 2HP, 380-415V , 50HZ 6905003 MOTOR, 38 0V , 50HZ C O N FI DE N T AI L IN F O R M AT O
I N O FS W AO
C , A D I VIS I NO
O F M -IL . L .C ,. IN HT E BA S E N CE O F E XPR SE S W RIT T E N
P E R M IS O N. SW
ACO H AS L O A NE D T H IS CO P Y W IT H T H E MUD CLE ANE R
U N D E RS T A N D ING T H A AT )( IT W I L N O T BE R E P RO D U C E D
9672370-03 & 9672370-03L 9672303-01 STA RTE R KIT, 3 MOTOR, UL, 440-480V, 60HZ E M3C00010 M OTOR, 2HP, 440-480V , 60HZ 6912002 MOTOR, 48 0V , 60HZ ( B) IT W IL NO
T BE U SE D F O RA N Y P UR P O S E X C E P T
T HAT F O R W HI CH IT W AS L O AN E D A N D (C ) IT W IL B E
SH
EET SCALE SIZE DRAW INGNO. REV
R E T UR N E D O N D E M A N DO R U PO N C O M P L ET IO N O F
T HE CO N T R A CTE D W R K , W HI CH
O E V E R CO M ES F IR S T. 1 OF 2
CONFIGURAT ION IT EM #14 DE SCRIP TION ITE M #15 DES CRI PT ION ITE M #16 DE SCRIP TION A C K N O W LE D G ED : _ _ _ _ _ _ _ _ _ D A TE :_ _ _ _ _ _ _ _ _ N EXT ASSY T O PAS SY 1:1 2 D 96723 70 -
Section 9.01
Document Title: Final Assembly
Mongoose PT Platform Mud Cleaner
Section 9.01
12 B B
E
8
10
7
3 1:6
5 5
A A
5
6 6
15 2
15 14 16
15 14
15
C
14
C
4
1
3 D 3 D
ADD HIGH TEMP RED SILICONE BETWEEN
9 7 SKID WELDMENT AN DBYPASS PLATE
2
7 11
12
7
7
10
8 10
8
SECTION A-A 2-12 6T4 MONGO OSE PT PLATFORM
MUD CLEANER
1:4 SECTION B-B
1:4
M- IL. L.C .
595 0 NO RT H COURS E DRIVE , HOUST ON ,T EX A S 7 70 72
SCALE SHEET SIZE DRAWI NGNO. REV
1: 12 2 OF 2
F IL E NA ME: Sw acoD 2
D 9672370 -
5
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item
Description Part Number Qty.
Number
1 Mongoose PT Unfinished Unit 9672160 1
2 D-Silter Assembly, 6T4 Mongoose PT Mud Cleaner Platform 9672411 1
3 2-12 D-Sander Assembly Mongoose PT Mud Cleaner Platform 9672412 1
4 Cable Tower Weldment, Mongoose 9672149 1
5 Cover Plate, Cable Retainer Tower 9672155 1
6 Cover, Skid Bypass Opening, Mongoose 9672148 1
7 Flat Washer M12 Metric 304SS 05-305 36
8 Hex Nut M12 x 1.75 Metric 304SS 03-415 18
9 HHCS M12 x 40 Metric 304SS 04-1106 14
10 Lock Washer M12 Split 304SS 05-306 18
11 HHCS M12 x 45 Metric 304SS Hex Head Cap Screw 04-1270 4
12 Decal Arrow Rotation 9650367 6
Starter Kit, Mongoose 3-Motor, UL, 575-600V, 60Hz for Configurations 9672303-03 1
9672360-11 & 9672360-11L
Starter Kit, Mongoose 3-Motor, UL, 380-415V, 50 Hz for Configurations 9672303-02 1
13
9672360-07, 9672360-07L, 9672360-88
Starter Kit, Mongoose 3-Motor, UL, 440-480V, 60 Hz for Configurations 9672303-01 1
9672360-03 & 9672360-03L
Motor, Vibrator, 2HP, 575-600V, 60 Hz for Configurations 9672360-11 & EM3C00137 2
9672360-11L
Motor, Vibrator, 2HP, 380-415V, 50 Hz for Configurations 9672360-07, EM3C00110 2
14
9672360-07L & 9672360-88
Motor, Vibrator, 2HP, 440-480V, 60 Hz for Configurations 9672360-03 & EM3C00111 2
9672360 -03L
Motor, 0.6 HP, Elliptical Motion, 575V, 60 Hz for Configurations 9672360-11 EM3C0038 1
& 9672360-11L
Motor, 0.6 HP, Elliptical Motion, 380V, 50 Hz for Configurations 9672360-07, 6905003 1
15
9672360-07L & 9672360-88
Motor, 0.6 HP, Elliptical Motion, 480V, 60 Hz for Configurations 9672360-03 6912002 1
& 9672360-03L
16 Wiring Kit, 3 Motor, UL 9672307-01 1
3. APPROXIMATE WEIGH T
74.6 3 MOTOR W /O BYP ASS: 5671 LBS
4. TORQUE LINEAR (LARGE) M OTOR BO LTS TO 320 FT- LBS.
5. TORQUE ELLIPTICAL (SM ALL) MOTO RBOLTS TO 180 FT-LBS.
97.3
82. 9
18. 2
ISO VIEW
1:20
BOLT UP FOR
88.3 90. 0 10 IN. 150 LB FLANGE
84. 5
74. 2
62. 2 61 .1
54. 4 16 9672307-01 WIRING KIT , 3 MOTOR, UL 1 -
15 SE ET ABLE MOTOR, 0.6HP, ELLIPTICALM OTI ON 1 -
14 SE ET ABLE MOTOR, VIBRATOR 2 -
30. 1 13 SE ET ABLE STAR TER K IT , MONGOOSE, 3-MOTOR 1 -
12 9650367 DECAL AR ROW ROTATION 6 -
11 HH CS_M12X45M M HHCS M1 2 X45m m LG 4 04-1 270
10 SPLITLOCK_M1 2 SPLIT LOCK W ASHER M1 2 REGULAR 18 05-306
9 HH CS_M12X40M M HHCS M1 2 X40m m LG 14 04-1 106
31. 5
63. 0 8 HE XNUT_M 12 HEX NU T M1 2 18 03-41 5
33 .5 19. 8 63. 0 7 FLATWSHR_M1 2 FLAT W ASHER M 12 NARROW 36 05-305
6 9672148 COVER, SKID BYP ASS OPENING 1 -
5 9672155 COVER PLA TE, CABLE RETAINER TOWER 1 -
11 3.2 4 9672149 CABLE TO WER W ELDMENT 1 -
3 9672412 2- 12 D- SANDER ASS EM BLY M UD CLE ANER 1 -
2 9672411 D- SIL TER ASSY 6 T4 2- 12 MONGOOSE PT MUDCLEANER 1 -
1 9672160 MONGOOSE PT ASSEMBLY, U NFINISHEDU NIT 1 -
Item Docume nt Number Tit le Quan tity 304SST
Number
9672360-11 & 9672360-11L 9672303-03 S TAR TER KIT, 3 MOTOR , UL, 575-600V , 60H Z EM3C 00137 MOTOR , 2H P, 575-600V , 60H Z EM3C 00038 MOTOR , 575V , 60HZ
9672360-07 & 9672360-07L 9672303-02 S TAR TER KIT, 3 MOTOR , UL, 380-415V , 50H Z EM3C 00110 MOTOR , 2H P, 380-415V , 50H Z 6905003 MOTOR , 380V , 50HZ M- I L .L . C.
2-12 6T4 MONGOOSE PT PLATFORM 5950 NORT HCOURS E DRI VE , HOUS TON , TE XA S 77 07 2
9672360-03 & 9672360-03L 9672303-01 S TAR TER KIT, 3 MOTOR , UL, 440-480V , 60H Z EM3C 00111 MOTOR , 2H P, 440-480V , 60H Z 6912002 MOTOR , 480V , 60HZ SCALE SHEET SIZE D RAW ING NO. RE V
1: 12 2 OF 9
Section 9.02
Document Title: 2-12 6T4 Final Assembly/9672360
Mongoose PT Platform Mud Cleaner
5 B B
Section 9.02
E
6
10 8
7 SECTION D-D
1
2-12/6T4 Assembly
1:6
2 A A 2
2
3 3
14 4
14 13 15
13
14 14
C
13
1 6
D 1 D
ADD HIGHTEM P RED SILICO NE BETW EEN
9 7 SKID WELDMENT AND BYPASS PLATE
4
7 11
5
7
7
10
8 10
5
6
NOTE: 2-1 2 6 T4 MONGOO SEP TP LATFORM MUD CLEANER
11 3.3 1. PERFO RM THE FACTORY AC CEPTANCE TEST USING THE M OST
CU RRENT REVISION OF MONGO OSE-PT23.D OC LOC ATED IN
SWACO DO CS UNDER FACTORY ACCEPTANCE TESTS.
2. UNI TM UST BE W EIGHED BEFOREUNIT TAGIS APPLIED (A TEX ONLY). STAMP
WEIGH TO N APPROPRIA TE L INES ON UN IT TAG. USE CONVERSION
FAC TOR OF .4 536 TO C ONVERT (LBS. )T O(Kg), SEE EXAMPLE
BELOW.
EXAMPLE: 5671 LBS x. 4536 = 2572 (Kg)
ISO VIEW
1:20
97. 3
82.9
18. 2
9 67236 0-10 & 96 72360-10L 967230 1-0 3 STARTER KIT,2 MOTOR, UL, 575-600V, 60HZ EM3C 00137 MOTOR, 2HP, 57 5-60 0V,6 0HZ
9 67236 0-06 & 96 72360-06L 967230 1-0 2 STARTER KIT,2 MOTOR, UL, 380-415V, 50HZ EM3C 00110 MOTOR, 2HP, 38 0-41 5V,5 0HZ M-IL .L .C.
9 67236 0-02 & 96 72360-02L 967230 1-0 1 STARTER KIT,2 MOTOR, UL, 440-480V, 60HZ EM3C 00111 MOTOR, 2HP, 44 0-48 0V,6 0HZ
2-12 6T4 MONGOOSE PT PLATFORM 5 950 NORT HCOURS E DRIVE , HOUST ON ,T E XA S 77 07 2
SCALE SH
EE T SI ZE DR
A WING NO. R EV
MUD CLEANER 2 MOTOR 1 :12 4 OF 9
F IL E NA ME: Swaco D 2
CONFIGURATION ITEM #13 DESCRIPTION ITEM #14 DESCRIPTION D 96723 60 D
Section 9.02
2-12/6T4 Assembly
Section 9.02
J
SECTIO N H-H
10 8 1:6
7
2-12/6T4 Assembly
3
2
3 3
13 14 4 13
14 13
14
14
1 H H
1 6
9
7 AD DHIGH TEMP RED SIL ICO NEBETWEEN
4 11 SKID WELDMENT AND BYPASS PLATE
7
5
7
10 7 2-12 6T4 MONGOOSE PT PLATFORM
8 10 MUD CLEANER 2 MOTOR
8
M-IL .L .C.
SECTION F-F SECTION G-G 5 950 NORT HCOURS E DRIV E ,HOUS TON , TE X AS 77 07 2
SCALE SH
EE T SI ZE DRAW ING NO. R EV
1:1 2 5 OF 9
F IL E NAM E: Sw acoD 2
D 9672 360 D
7
8
11 3.7 NOTE: 2-12 6T4 MONGOOSE PTP LATFORM MU DCLEANER
1. PERFORM THE FACT ORYACCEPTANCE TEST USINGTHE MOST
CU RRENT REVISION OF M ONGOOSE-PT23. DOCLOCATEDIN
SW ACO DOCS UNDERFAC TORY ACCEPTANCE TESTS.
2. UNIT MU ST BEW EIGHED BEFORE UNIT TAG ISAPPLIED (ATEX ONLY) STAMP
WEIGH T ON APPROPRIATE LINESON UNITTAG. USE CONVERSION
FACTOR OF .453 6TO CONVERT (LBS) TO (KG) SEE EXAMPLE
BELOW
EXAM PLE: 5671 LBS X .4 536= 2572 KG
3. APP ROXIMATE WEIGHT
3 MO TO RW /O BYPASS 5675 LBS
4. TORQUE LINEAR(LARGE)MO TOR BO LTS TO 320 FT-LBS
5. TORQUE ELLIPTICAL (SMALL) MOTOR BOLTS TO 1 80 FT-LBS
74. 7
ISO VIEW
1:20
97.3
82.9
18. 2
BOLTUP FOR
10 IN 150 LBFLANGE
967 2360 -09 & 9672 360- 09L 96 72304- 02 STARTER KIT, 3 MOTOR, ATEX, 3 80-41 5V, 5 0HZ EM3C00 110 MO TOR, 2 HP, 380 -415 V, 50HZ 6 90500 3 MOTOR, 38 0V, 50 HZ
M -I L .L. C.
967 2360 -05 & 9672 360- 05L 96 72304- 01 STARTER KIT, 3 MOTOR, ATEX, 4 40-48 0V, 6 0HZ EM3C00 111 MO TOR, 2 HP, 440 -480 V, 60HZ 6 91200 2 MOTOR, 46 0V, 60 HZ 595 0 NORT HCOURSE DRIVE, HOUSTON ,T EXAS7 7 072
CONFI GURATION I TEM# 15 DESCRIPTION ITEM #4 DESCRIPTI ON I TEM# 5 DESCRIPTI ON SCALE SHEET SIZE DRAW INGNO. RE V
1:1 2 6OF 9
Section 9.02
2-12/6T4 Assembly
P
2-12/6T4 Assembly
SECTION N-N
10 11 1:6
8 7
9
DETAIL P
1:3
SECTION M-M
3
2
3 3
4 15
6
4
15
15
4
4
M
16
1 7
13 15 1 N N
8 ADD HIGH TEMP REDSILICONE BETWEEN
12 SKID WELDMENT AND BYPASS PLATE
9 8
6
2-12 6T4 MONGOOSE PT PLATFORM
8 8
MUD CLEANER 3 MOTOR, ATEX
11 11
10 SEC TION K-K 10
M- I L. L.C .
1:4 SECTIO N L-L 595 0 NORT H COURS E DRI VE , HOUS TON , T E XA S 770 72
SCALE SHEET SIZE D RAWI N
G NO. REV
7 OF 9
9
10
1 13.3 NOTE: 2- 12 6 T4 MONGOOSE PTP LATFORM MUD CLEANER
3. APPROXIMATE WEIGH T
3 MOTOR W /O BYPASS: 5671 LBS
4. TORQUE LINEAR (LARGE) MOTOR BOLTS TO 320 FT-LBS.
ISO VIEW
1:20
97. 3
82. 9
18.2
BOLT UP FOR
10 IN. 150 LB FLANGE
M- IL. L.C .
2-12 6T4 MONGOOSE PT PLATFORM 595 0 NORT H COURS E DRIVE ,HOUS TON , TE XA S 77 072
A M E: Sw ac o D 2
9672360-88 9672303-02 S TARTE R K IT, 3 MOTOR, UL, 380-415V, 50H Z EM 3C 00110 MOTOR , 2HP , 380-415V, 50H Z 690500 3 MOTOR, 380V , 50HZ SCALE SHEE T SIZE DRAWI NGNO. RE V
1 :12 8 OF 9
FIL E N
C ON FIGU R ATI ON ITE M #13 D ES C RI PTI ON I TEM #14 DE SC R IP TION ITE M #15 D ESC R IP TION MUD CLEANER 3 MOTOR D 967236 0 D
Section 9.02
Mongoose PT Platform Mud Cleaner
Document Title: 2-12 6T4 Final Assembly/9672360
2-12/6T4 Assembly
14 14 5
12
T T
Section 9.02
R
SECTION Q -Q
1:6
2-12/6T4 Assembly
1:3
2
3 3
3
14
13 4
14 15
13
14 13
14
1
Q 1 6
Q
9 7 7 10 8 11 7 7 10 8
ADD HIGH TEM P RED SILICONE BETWEEN
SKID WELDMENT AND BYPASS PLA TE
M-IL .L .C.
SECTION S-S SECTION T-T 2-12 6T4 MON GOOSE PT PLATFORM 5 950 NORT HCOURS E DRIV E, HOUST ON ,T E XA S 77 07 2
C ALE
S SHEE T S IZE DRAWI NGNO. R EV
1:4 1:4 1:1 2 9 OF 9
11
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Mongoose PT Assembly, Unfinished Unit 9672160 1
2 D-Silter Assembly 6T4 Mongoose PT Mud Cleaner 9672539 1
3 Cover, Skid Bypass Opening 9672148 1
4 Cable Tower Weldment 9672149 1
5 Cover Plate, Cable Retainer Tower 9672155 1
6 Flat Washer M12 Regular 05-305 36
7 Hex Nut M12 03-415 18
8 HHCS M12 x 40 mm LG 04-1106 14
9 Split Lock Washer M12 Regular 05-306 18
10 HHCS M12 x 45 mm LG 04-1270 4
11 Decal Arrow Rotation 9650367 6
12 Wiring Kit, 3 Motor UL 9672307-01 1
Starter Kit, Mongoose, 3-Motor, UL, 575-600V, 60 Hz for Configurations
9672303-03 1
9672365-11 & 9672365-11L
Starter Kit, Mongoose, 3-Motor, UL, 380-415V, 50 Hz for Configurations
13 9672303-02 1
9672365-07 & 9672365-07L
Starter Kit, Mongoose, 3-Motor, UL, 440-480V, 60 Hz for Configurations
9672303-01 1
9672365-03 & 9672365-03L
Motor, Vibrator, 2 HP, 575-600V, 60 Hz for Configurations 9672365-11 &
EM3C00137 2
9672365-11L
Motor Vibrator, 2 HP, 380-415V, 50 Hz for Configurations 9672365-07 &
14 EM3C00110 2
9672365-07L
Motor Vibrator, 2 HP, 440-480V, 60 Hz for Configurations 9672365-03 &
EM3C00111 2
9672365-03L
Motor, 0.6 HP, Elliptical Motion, 575V, 60 Hz EM3C00038 1
15 Motor, 0.6 HP, Elliptical Motion, 380V, 50 Hz 6905003 1
Motor, 0.6 HP, Elliptical Motion, 480V, 60 Hz 6912002 1
3. APPROXIMATE WEIG HT
74.6
3 M OT OR W/O BYP ASS: 4665LBS
4. T ORQU EL INEAR (L ARGE) M OTOR BOLTS TO 320 FT- LBS.
18.2
ISO VIEW
1:15
74. 2
15 SEET ABLE MOTOR, 0.6HP, ELLIPTICAL MOTION 1 -
14 SEET ABLE MOTOR, VIBRATOR 2 -
13 SEET ABLE STARTER K IT , MONGOOSE, 3- MOT OR 1 -
12 9672307-01 WIRING KIT , 3 MOTOR, UL 1 -
11 9650367 DECAL AR ROW ROTATION 6 -
30.1 10 HHCS_M12X45MM HHCS M 12 X45mm LG 4 04-1 270
9 SPLITLOCK_M12 SPLIT LOCK W ASHER M12 REGULAR 18 05-306
8 HHCS_M12X40MM HHCS M 12 X40mm LG 14 04-1 106
7 HEXNUT_M 12 HEX NUT M1 2 18 03-41 5
6 FLATWSHR_M12 FLAT WASHER M 12 REGU LAR 36 05-305
31. 5
63.0 5 9672155 COVER PLA TE, CABLE RETAINER TOWER 1 -
33.5 1 9.8 64.5 4 9672149 CABLE TOWERWELDMENT 1 -
3 9672148 COVER, SKID BYP ASS OPENING 1 -
M I
L I
M E T E
R S A R
E I N R A C K E
B T S DRAW N De c-19-2 005
D O N
O T C A L E P R
S I N T S JA M
R E
M O
V E U R R S A N
B D S H
A R P D G E S
E
S U
R F
A C E R O U G H
N E
S S 2 5
1 M I
C R O I N
C H E S R M S CHECKE D M- I L.L .C .
T O
L E
R A N C
E S P E
R A N S I Y 1 4 .
5 M
T H
I R
D A N
G L E R O
P J E C T
I O N
T O
L E
R A N C
E S O N ENGI NEER 5950NORTHC
OU R
SED R
I VE,HOUSTO
N, TEXAS 770 72
. X X = / -
+ . 0
3 0 0 -
3 0 N C
I H E S = + / - 1
/ 3 2
. X = / -
+ . 0
6 0 3 0 -
6 0 N C
I H E S = + / - 1
/ 1 6
. X = / -
+ . 1
0 0 6 0 & O V
E R = + / - 1
/ 8 APPROVED
A N
G L
E S / -
+ 0 °
3 0
' C H A
M & C '
S I N K S + / - 2
°
9672365-11 & 9672365-11L 9672303-03 S TARTE R K IT, 3 MOTOR , U L, 575-600V, 60H Z E M3C 00137 MOTOR, 2HP, 575-600V , 60HZ E M3C 00038 MOTOR, 575V, 60HZ CO
N F ID EN T IA L
FINAL ASS EMBL Y 6 T4 MUD CL EAN ER
TH IS D R AW IN G A N D /O R S P EC IF IC A TI O
N EM B O D IES
9672365-07 & 9672365-07L 9672303-02 S TARTE R K IT, 3 MOTOR , U L, 380-415V, 50H Z E M3C 00110 MOTOR, 2HP, 380-415V , 50HZ 6905003 MOTOR, 380V, 50HZ CON F ID E NT IA L I NF O R M AT IO N O FS W AC O , A DI V IS IO N
O F M -I L. L .C ., I N TH E AB S E N CE O F E XP R ES W R IT E N MOD EL : MO NGO OS E PT P LATFO RM
P ER M IS IO N . S W AC O H AS L O A NE D T H IS C O P YW I T H TH E
U ND E R S TA N D IN G T H A AT )( IT W I L N O T B E R EP R O D UC E D
9672365-03 & 9672365-03L 9672303-01 S TARTE R K IT, 3 MOTOR , U L, 440-480V, 60H Z E M3C 00111 MOTOR, 2HP, 440-480V , 60HZ 6912002 MOTOR, 480V, 60HZ (B ) I T W IL N O TB E U SE D F O RA N Y P U R P O S E E X CE P T
TH A T F O R W H IC H I T W AS L O AN E D A ND ( C )I T W IL L BE SHEET SCALE SIZE DRA WINGNO. REV
R ET U R N ED O N D E M A N DO R U PO N C O M P L ETI O
N OF
Section 9.03
Document Title: Final Assembly
6T4 Assembly
Section 9.03
5 B B
6T4 Assembly
E
3
7
9
2 A A
2
2
14 4
14 13 15
13
14 14
13
3
1
D 1 D
ADD HIG H TEMP RED SILICONE BETWEEN
8 SKIDWELDMENT ANDBYPASS PLATE
6
4
10
6
5
6
6
9
7 9
7
SECTION A-A
1:4 SECTION B-B 6T4 MONGOOSE PT PLATFORM MUD CLEANER
1:4
M-I L .L . C.
A M E: SwacoD 2
SCALE SHEE T SI ZE D RAW ING NO. RE V
1: 12 2 OF 2
FIL E N
D 9672365 A
5
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Cover, Skid Bypass Opening 9672148 1
2 Cable Tower Weldment 9672149 1
3 Mongoose PT Assembly, Unfinished Unit 9672160 1
4 Wiring Kit, 3-Motor, UL 9672307-01 1
5 D-Silter Assembly 10T4-12 Mongoose PT Mudcleaner 9672771 1
6 3-12 D-Sander with Stand Assembly 9672461 1
7 Flat Washer M12 Narrow 05-305 36
8 Hex Nut M12 03-415 18
9 HHCS M12 x 40 mm LG 04-1106 14
10 Split Lock Washer M12 Regular 05-306 18
Starter Kit, Mongoose, 3-Motor, 575-600V, 60 Hz for
9672303-03 1
Configuration 9672385-11
Starter Kit, Mongoose, 3-Motor, 380-415V, 50 Hz for
11 9672303-02 1
Configuration 9672385-07
Starter Kit, Mongoose, 3-Motor, 440-480V, 60 Hz for
9672385-03 1
Configuration 9672385-03
Motor, Vibrator, 2 HP, 575-600V, 60 Hz for Configuration 9672385-11 9672303-03 2
12 Motor, Vibrator, 1.75 HP, 380-415V, 50 Hz for Configuration 9672385-07 9672303-02 2
Motor Vibrator, 2 HP, 440-480V, 60 Hz for Configuration 9672385-03 9672303-01 2
Motor, 0.6 HP Elliptical Motion, 575V, 60 Hz for Configuration 9672385-11 EM3C00038 1
13 Motor, 0.6 HP Elliptical Motion, 380V, 50 Hz for Configuration 9672385-07 6905003 1
Motor, 0.6 HP Elliptical Motion, 480V, 60 Hz for Configuration 9672385-03 6912002 1
14 HHCS M12 x 45 mm LG 04-1270 4
15 Cover Plate, Cable Retainer Tower 9672155 1
16 Decal, Arrow Rotation 9650367 6
97. 0
82. 6
16. 3
ISO VIEW
1:20
U N D ER S T A ND NI G T H A T A)( I T W IL N O T B E R E P O
R D U CE D
MU D CLEAN ER
9672385-03 9672 303-01 S TAR TE R KIT, 3 MO TOR , UL, 440-480V, 60H Z E M3C 00111 MOTOR, 2H P, 440-480V, 60H Z 6912002 MOTOR , 480V , 60HZ ( B) TI W I L N O T B E U S E D F O RA N Y UP R P O S E X C PE T
T HA T F O R W H IC H IT W AS L O A NE D A N D (C ) IT W I L B E
SHEET SCALE SIZE DRAWI NGNO. REV
R E T UR N E D O
ND E M A N D O R U P O N C O M P L ET IO N O F
T H E C O N TR A C TE D W O R K, W H ICH E V ER CO M ES F IR ST . 1 OF 2 1:12
Section 9.04
Document Title: Final Assembly
3-12/10T4 Assembly
Section 9.04
15 16 13 B B
E
SECTION D-D
SECTIO N C- C 7 9
A A DETAIL E
12 12 2 5
1:3
5
5
6
6 5
6
12 12 2 4
11 13
11
12 12
C
11
D 3 D
3
AD DHIGH TEMP RED SIL ICON EBETWEEN
SKID WELDMENT AND BYPASS PLATE
9 14
7 7
2 15
7 7
10
10
8
8
SECTION A-A M-IL .L . C.
5
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Cover, Sid Bypass Opening 9672148 1
2 Cable Tower Weldment 9672149 1
3 Mongoose PT Assembly, Unfinished Unit 9672160 1
4 Wiring Kit, 3 Motor, UL 9672307-01 1
5 D-Silter Assembly 8T4 3-12 Mongoose PT Mud Cleaner 9672396 1
6 3-12 D-Sander with Stand Assembly 9672461 1
7 Flat Washer M12 Narrow 05-305 36
8 Hex Nut M12 03-415 18
9 HHCS M12 x 40 mm LG 04-1106 14
10 Split Lock Washer M12 Regular 05-306 18
Starter Kit, Mongoose, 3 Motor, UL, 440-480V, 60 Hz
9672303-01
For Assemblies 9672380-03 & -03L
Starter Kit, Mongoose, 3 Motor, UL, 380-415V, 50 Hz
11 9672303-02 1
For Assemblies 9672380-07 & -07L
Starter Kit, Mongoose 3 Motor, UL, 575-600V, 60 Hz
9672303-03
For Assemblies 9672380-11 & -11L
Motor, Vibrator, 2 Hp, 440-480V, 60 Hz
EM3C00111
For Assemblies 9672380-03 & -03L
Motor, Vibrator, 1.75 Hp, 380-415V, 50 Hz
12 EM3C00110 2
For Assemblies 9672380-07 & -07L
Motor, Vibrator, 2 Hp, 575-600V, 60 Hz
EM3C00137
For Assemblies 9672380-11 & -11L
Motor, 0.6 Hp, Elliptical Motion, 480V, 60 Hz
6912002
For Assemblies 9672380-03 & -03L
Motor, 0.6 Hp, Elliptical Motion, 380V, 50 Hz
13 6905003 1
For Assemblies 9672380-07 & -07L
Motor, 0.6 Hp, Elliptical Motion, 575V, 60 Hz
EM3C00038
For Assemblies 9672380-11 & -11L
14 Cover Plate, Cable Retainer Tower 9672155 1
15 HHCS M12 x 45 mm LG 04-1270 4
16 Decal, Arrow Rotation 9650367 6
17 Wedge, Mongoose Screen Clamping 5895001 2
REV D ES CR IP TIO N DR A FT ER CH K D AP PR VD D AT E
113 .3 A ADDEDQ TY (2) 5895001 (I TEM# 17) M AL 8/29/07
NOTE: 3-1 28 T4 M ONG OOSEPT PLATFORM MUD CLEANER
1. PERFORM THEFACTORY AC CEPTANCE TEST U SING THEM OST
C URRENT REVISION OF MONGOOSE-PT23.DOC LOCATED IN
SWACO DOCS UNDER FACTORY ACCEPTANCE TESTS.
2. UNIT MUST BE WEIGHED BEFORE U NIT TAG IS APPLIED (ATEX ONLY). S TAMP
WEIGHT ON APPROPRIATELINES ONU NIT T AG. U SE CONVERSION
F ACTOR OF .453 6T OCO NVERT (LBS.) T O(Kg), SEE EXAMPLE
BELOW .
EXAMPLE: 65 00 LBSx .453 6= 2948 (K g)
3. APPROXIMATEWEIGHT
3 MOTOR W/O BYPASS: APP ROX. 6500LBS
4. TORQUEL INEAR (LARGE) MOTOR BO LTS T O320 FT-LBS.
80.5 5. TORQUEELLIPTICAL (SMALL) MOTO RB OLTS TO 1 80 FT- LBS.
97 .0
82. 6
18. 2
ISO VIEW
1:20
BO LT UP F OR
90. 8 10 IN. 1 50LB FL ANG E 17 5 89 50 01 W ED G E, MO N GO OS E SC RE E N C LAMP I N G 2 -
90. 0
16 9 65 03 67 D EC AL ARR O W RO TA TIO N 6 -
84. 5
15 H H CS _M12 X 45M M H HC S M 12 X 45 mm L G 4 04 -12 70
74 .2 14 9 67 2 155 C O VE R P LAT E, C AB LE RE T AIN ER TO W ER 1 -
6 9 67 24 61 3 -12 D -S AN DE R W / ST AND AS SE M BL Y 1 -
4 96 72 30 7- 01 W I RI N G KI T ,3 MO TO R, U L 1 -
3 9 67 2 160 M O NG OO S E PT AS SEM B LY , U N FIN I SH ED U N IT 1 -
31. 5
2 9 67 2 149 C AB L E T OW ER W EL DM EN T 1 -
33. 5 19. 8
63.0 1 9 67 2 148 C O VE R, S KI D B YPAS S O PE NIN G 1 -
I T EM P AR T N U MB ER D ES C RI PTI O N Q TY 30 4 SS T
113 .2 N U MB ER
64.5
BIL LO FM ATERI AL
UN LE SS OT HE R WIS E SPEC IF I ED: SI GNA TU RES DA TE
DI
MENSIO
NS AREIN I
NCHES
MI
LIMETE
RS AREIN B
RACKETS DRAW N T R OS E 0 2 -14- 06
DONOT S
CALE PINTS
R
RE
MOVE B
URRS AD SH
N ARP EDGES
SU
RFACEROUGHNSS 1
E 25 MICROINCHESRMS CHECKE D M- I . L . C.
L
TO
LERANC
ES PERANSIY14.5M
TH
IRD AN
GLE PRJECT
O ION
TO
LERANC
ES ON 5 9 5 0 NORTHC
OU R
SE D
RI VE,HOUSTO
N, TEXAS 7 0 7 2
ENGIN EER
.XX= +/- .030 0-
30 I
NCHES =+/-1
/32
.X = +/- .060 30-60 I
NCHES =+/-1
/16
.X = +/- .10 60& OVER =+/-1
/8 APPROVED FIN AL AS S EM BLY 3- 1 2 8T4
AN
GLES +
/- 0°3'
0 CHAM &C'SINKS+/-2
°
9 6 72 3 8 0 -1 1 & 9 67 2 3 8 0 -1 1 L 96 7 2 3 03 - 03 STAR TER KIT, 3 MO TO R, UL , 5 7 5 -6 0 0 V, 60 H Z EM3 C 00 1 3 7 MO TO R , 2 HP , 5 7 5 -6 0 0 V, 60 H Z EM3 C 00 0 3 8 MOTO R , 5 7 5V , 6 0 HZ CO NFID ENTIAL
THNISFIDDRA
CO ENTWIAI LI
NG NFORMA
AND/OTRIONSPEOFCSW O
IFCATAC
IO
N, ADIEMVI BODI
SIONES M OD EL : M ON GOO S E P T PLA T FOR M
9 6 72 3 8 0 -0 7 & 9 67 2 3 8 0 -0 7 L 96 7 2 3 03 - 02 STAR TER KIT, 3 MO TO R, UL , 3 8 0 -4 1 5 V, 50 H Z EM3 C 00 1 1 0 MOTO R, 1 .7 5 HP, 3 80 - 4 1 5V , 5 0 HZ 69 0 5 0 03 MOTO R , 3 8 0V , 5 0 HZ OFM- IL. L.C., I NTHE ABSENCEOF EXPR ES WRIT EN
PERMISION. SWACO HASLOANEDTHISCOPYWI THTHE M U D CLE AN ER
UNDERSTANDINGTHAT( A) IT WI L NOTBEREPRODUCED
9 6 72 3 8 0 -0 3 & 9 67 2 3 8 0 -0 3 L 96 7 2 3 03 - 01 STAR TER KIT, 3 MO TO R, UL , 4 4 0 -4 8 0 V, 60 H Z EM3 C 00 1 1 1 MO TO R , 2 HP , 4 4 0 -4 8 0 V, 60 H Z 69 1 2 0 02 MOTO R , 4 8 0V , 6 0 HZ (BA) TI TWI
TH L NOTB
FORWHI CHIETWAUSSEDLOA FOR
NEDAN RPO
ANYD(PUC) ITSWIEEXC
L BEEPT SHEET SCAL E SIZ E DRA WINGNO. REV
REET URNE
TH CONTDRACT O
NDEDWEMANDOROK,
R WHI COMPLE
UPOCHN EVE RCOMESF TI O
N IOFRST. 1 OF 2
Section 9.05
Document Title: Final Assembly
3-12/8T4 Assembly
Section 9.05
14 B B
E
1
10
7 SECTION D-D
1
7 9
DETAIL E
12 16 13 1:3
12
6 2 SECTIO NC-C 5
5 A A 5
5
6 6
12 17 2 17
12 11 13
11
12 12
11
3 1
D 3 D
ADD HIGH TEM PRED SILICONE BETWEEN
9 7 SKID WELDMENT AND BYPASSPLATE
2
14 7 15
7
10 7
8 10
8
SECTION A-A 3-12 8T4 MONGOOSE PT PLA TF ORM
MUD CLEA NER
1:4 SECTION B-B
1:4 M-I L .L . C.
1: 12 2OF 2
F IL E NAM E: Swa c o D 2
D 9672380 A
5
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Cover, Skid Bypass Opening 9672148 1
2 Cable Tower Weldment 9672149 1
3 Mongoose PT Assembly, Unfinished Unit 9672160 1
4 Wiring Kit, 3 Motor, UL 9672307-01 1
5 D-Silter Assembly 10T4 3-12 Mongoose PT Mud Cleaner 9672661 1
6 3-12 D-Sander with Stand Assembly 9672461 1
7 Flat Washer M12 Narrow 05-305 36
8 Hex Nut M12 03-415 18
9 HHCS M12 x 40 mm LG 04-1106 14
10 Split Lock Washer M12 Regular 05-306 18
Starter Kit, Mongoose, 3 Motor, UL, 440-480V, 60 Hz
9672303-01
For Assembly 9672875-03
Starter Kit, Mongoose, 3 Motor, UL, 380-415V, 50 Hz
11 9672303-02 1
For Assembly 9672875-07
Starter Kit, Mongoose 3 Motor, UL, 575-600V, 60 Hz
9672303-03
For Assembly 9672865-11
Motor, Vibrator, 2 Hp, 440-480V, 60 Hz
EM3C00111
For Assembly 9672875-03
Motor, Vibrator, 1.75 Hp, 380-415V, 50 Hz
12 EM3C00110 2
For Assembly 9672875-07
Motor, Vibrator, 2 Hp, 575-600V, 60 Hz
EM3C00137
For Assembly 9672865-11
Motor, 0.6 Hp, Elliptical Motion, 480V, 60 Hz 6912002
13 Motor, 0.6 Hp, Elliptical Motion, 380V, 50 Hz 6905003 1
Motor, 0.6 Hp, Elliptical Motion, 575V, 60 Hz EM3C00038
14 HHCS M12 x 45 mm LG 04-1270 4
15 Cover Plate, Cable Retainer Tower 9672155 1
16 Decal, Arrow Rotation 9650367 6
17 Assembly, Vent Hood 10T4 D-Silter with Ducts 9673015 1
18 Assembly, Vent Hood Mud Cleaner 9673000 1
19 Wedge, Mongoose Screen Clamping 5895001 2
NOTE: 3-1 2 10T4MONG OOSE PTP LATFORM MUD CLEANER W /VENT HO OD A ADDED (2) 58 950 01TO CABLETOWER MAL 8 /3 1/0 7
1. PERFORMTHE FACTORY AC CEPTANCETEST USING THE MOST
CUR RENTREVIS ION OF MONGOOSE-PT2 3.DOC LOCATED IN
S WACO DOCS UNDER FACTORY AC CEPTANCE TESTS.
2. UNIT MUST BEWEIGHED BEFORE UNIT TAG IS APPLIED(ATEX ONLY). STAMP
WEIGHT ON APPROPRIATE LINES ON UNIT TAG. USE CONVERSION
FACTOR OF . 4536TO CONVERT(LBS.) TO (Kg), SEE EXAMPLE
BELOW .
EXAMPLE: 74 00LBSx . 453 6= 335 6(Kg)
3. APPROXIMATE WEIG HT
3 MOTOR W/O BYPASS: APPROX. 740 0LBS
4. TORQ UELINEAR (LARGE) MOTOR BOLTSTO 32 0FT-LBS .
5. TORQ UEELLIPTICAL (SMALL) MOTOR BOLTS TO 1 80 FT-LBS.
93.8
ISO VIEW
1:20
19 589 500 1 WEDGE, MONGO OSE SCREEN CLAMPING 2 -
18 9673 000 ASSEMBLY, VENT HOOD MUD CLE ANER 1 -
17 9673 01 5 ASSEMBLY, VENT HOOD 10T4 D-SILTER WITH DUCTS 1 -
16 965 036 7 DECAL ARROW ROTATION 6 -
15 967215 5 COVERPLA TE, CABLERETAINER TOW ER 1 -
14 HHCS _M1 2X4 5MM HHCS M12 X45 mm LG 4 04 -1270
103. 5
BOLT UP FOR 13 SEETABLE MOTOR, 0.6 HP, ELLIPTICALMOTION 1 -
90.8 92.1 1 0IN 15 0LB FLANGE 12 SEETABLE MOTOR, VIBRATOR 2 -
11 SEETABLE STARTERK IT, MONG OOSE, 3 -MOT OR 1 -
78.1 10 SPLITLOCK_M1 2 SPLIT LOCK WASHER M12 REGULAR 18 05 -30 6
6 3.4 9 HHCS _M1 2X4 0MM HHCS M12 X40 mm LG 14 04 -1 106
6 2.6 8 HEXNUT_M12 HEX NUT M1 2 18 03 -415
54.4 7 FLATWS HR_M1 2 FLAT WASHER M1 2NARROW 36 05 -30 5
6 9672 461 3-1 2D-SANDER W/ST AND AS SEMBLY 1 -
5 9672 661 D-SILTER ASSY10T4-12 MONGOOSE PT MU DCLEANER 1 -
2 9.9 4 9672 307-01 WIRING KIT, 3 MOTOR, UL 1 -
3 967216 0 MONG OSE PT ASSEMBLY, UNFINIS HEDUNIT 1 -
2 967214 9 CABLE TOWERWELDMENT 1 -
1 967214 8 COVER,SKID BYPASS OPENING 1 -
31 .5 Item Docum en t Tit le Quantity 304 SST
33.5 19. 8 Number Num ber
6 3.0 BIL LO FM ATERI AL
UN LESS OT HE RW IS ES PE CIF I ED : SIG NATU RE S DATE
1 13. 3 DIME NSIONSAREININCH ES
MIL LIMETER SAR
EINBRAC KETS DRAWN
6 4.5 DON OTSCALEPR INTS S ARo se Mar-30 -20 07
REMOVEBU RSAN DSHA PEDGE
R S
SUR FA
CE R UGHN
O ESS125 MICR OINCH
ESRMS
CHECK ED M-I L .L .C.
TOLE RANCESPERANS I Y14 .5M
THI
TOLE DANC
RANGL SON
E EPRO
: JECTI ON ENGI NEER 59 50NORTH C
OURSEDRIV E,HO
USTON,T EXAS770 72
.XXX +/-.005 FRAC+/ - 1/ 32
9672875-11 9672303-03 STA R TE R KIT, 3 MOTOR, UL, 575-600V , 60H Z E M3C 00137 M OTOR , 2H P, 575-600V , 60H Z E M3C 00038 MOTOR , 575V , 60H Z .XX +/-.01
.X +/-.0351 ANG+/N- .00
CONCE DEG
1/52 DIA APPRO VED ASSEMB LY, 3-12 10T 4 MUD CLEANER
CONFID ENTIAL
9672875-07 9672303-02 STA R TE R KIT, 3 MOTOR, UL, 380-415V , 50H Z E M3C 00110 MOTOR , 1. 75HP , 380- 415V , 50H Z 6905003 MOTOR , 380V , 50H Z THI
CONSF DRA
IDENWT IIANG
LI AND/
NFORMA
ORT IOSP
NOFSWACO,
ECIF ICATIONAEMB
DI O
VISDI
IOENS
W / VENT HO OD
OFM-
PER MISIO
IL N.
. L.CSWA
, I. CNTO
HEHASABLOA
SENNCEDTH
EOF ISEXCO SSWRI
PPREYWI T HTHT ETEN
9672875-03 9672303-01 STA R TE R KIT, 3 MOTOR, UL, 440-480V , 60H Z E M3C 00111 M OTOR , 2H P, 440-480V , 60H Z 6912002 MOTOR , 480V , 60H Z B(UND RSTA
) IETWI L LNOT
N DINBGTHAT
E USE(ADFORANYPUR
) IT WIL LNOT BEPROSE EPREOXCE
DUCPETD
MODEL : MONGOOSE PLATFORM
FORWHI
THAUT RNEDO CHI TWA WIL BE SHEET SCALE SI ZE DRAW INGNO. REV
RET NDEMAN DOR S LOUPANEDA
ON COND(MPLC)ETIT IONOF
THECONTRACTED W O RK, W HICH EVERCOM ESFIRST. 1 OF 2 1:12
Section 9.06
Document Title: Final Assembly
3-12/10T4 Assembly
Section 9.06
15 16 13 B B
E
SECTION D-D
1:6
10 8
1
SECTION C- C 7 9
18 A A DETAIL E
12 12 2 5 1:3
5 17
5
6 6 5
6
1 2 19 2 19 4
12 11 13
11
12 12
C
11
D 3 1 D
3
ADDH IG HTEMP RED SILICONE BETWEEN
SKIDWELDMENT ANDB YPASS PLATE
9 14
7 7
2 15
7 7 ASSEMBLY NOTE:
10
10 FOR THE D-SILTER VENT HOOD TO FIT PROPERLY
8 THE D-SILTER ASSEMBLY MUST BE PERPENDICULAR
8
SECTION A-A AND C ENTERED WITHIN THE HEADER BOX.
M- IL .L .C.
1:4 SECTION B-B SH
595 0NORTH COU RSEDRIVE,HOUSTON ,TEXAS77072
EE T
SCALE SI ZE DRAWING NO. REV
1:4 1:12 2 OF 2
F IL E NAM E: Sw ac o D 2
D 9672875 A
5
NOTES:
Supplier Logo
Equipment:
Mongoose Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 U-Bolt, CS 8” Pipe, 5/8-11 NC, 11.375” LG with Nuts 1289105 2
2 U-Bolts 10” Pipe x ¾-10 NC x 13.813 LG with Nut 1289140 2
3 Drive Screw #4 x .188 LG, SS 1492031 4
4 Gauge 0-60 PSI (0-400 kPa) 2-1/2” ¼” NPT LM 2422177 1
5 Coupling Grooved End Bolt T-Gasket 4” 1000 PSI 5015026 2
6 Coupling, Grooved 6” 5015029 4
7 Coupling Grooved End Bolt T-Gasket 8” 800 PSI 5015030 1
8 Coupling Grooved End Bolt T-Gasket 10” 800 PSI 5015031 1
9 Elbow Grooved End 90° D SR M1 SCH 40 6” 5030860 2
10 Clone Assembly Urethane 12”, Grooved End 9621280 2
11 U-Bolt 7-3/8” ID 5/8-11 NC x 8-3/4” LG 9621289 2
12 Manifold, Feed 2-12 Slang Mount D-Sander 9621379 1
13 Manifold Overflow 2-12 Slant Mount D-Sander 9621380 1
14 Unit Tag, SWACO Nameplate 9650360 1
15 Bracket, Support D-Sander Clones 9671961 1
16 Bracket, Mating 2-12 D-Sander 9671962 1
17 Weldment, Stand 2-12/3-12 D-Sander Mud Cleaner 9672356 1
18 Stand Leg Weldment, D-Sander 9672361 2
19 Nipple, Grooved End Stub 8” 9697001-13 1
20 Nipple, Groove End Stud 10” 9697001-14 1
21 Flat Washer M12 Regular 05-305 48
22 Flat Washer 5/8” 05-174 8
23 Flat Washer ¾” 05-160 4
24 Hex Nut M12 03-415 24
25 Hex Nut 5/8 03-145 8
26 Hex Nut ¾ 03-404 4
27 HHCS M12 x 35 mm LG 04-1105 4
28 HHCS M12 x 40 mm LG 04-1106 20
29 Split Lock Washer M12 Regular 05-306 24
30 Split Lock Washer 5/8 Regular 05-176 8
31 Split Lock Washer ¾ Regular 05-236 4
68.0
18
0
8
13
2 22.00 61.7 5
17
2
31 SPLITL OCK750R SPLI TL OCKW ASHE R 3/4RE GUL AR 4 05- 236
30 SPLITL OCK625 R SPLI TL OCKW ASHE R 5/8RE GULAR 8 05- 176
ISO VIEW 29 SPLITL OCK_ M1 2 SPLI TL OCKW ASHE R M12 RE GULAR 24 05- 306
12 28 HHCS_ M1 2X40MM HHCS M 12 X 40mm LG 20 04- 1106
1:1 0 27 HHCS_ M1 2X35MM HHCS M 12 X 35mm LG 4 04- 1105
7 26 HEX NUT750 HEX NUT 3/4 4 03- 404
19 25 HEX NUT625 HEX NUT 5/8 8 03- 145
24 HEX NUT_ M12 HEX NUT M1 2 24 03- 415
18
6 SE E SHEE T 2 23 F LATWSH R750N FLA T WA SHER 3/4 N 4 05- 160
9 A 22 F LATWSH R625N FLA T WA SHER 5/8 N 8 05- 174
10 21 F LATWSH R_M 12 FLA T WA SHER M 12 REGULA R 48 05- 305
20 9697001-1 4 NIP PLE , GROOVE E ND STUB 10 I N 1 -
6
19 9697001-1 3 NIP PLE , GROOVE DE ND STUB 8 I N 1 -
11
13 18 9672361 STAND LE GWE LDME NT, D-SA NDE R 2 -
17 9672356 WE LDM ENT, S TA ND 2- 12 /3-1 2 D-SA NDER 1 -
MUDCLE A NE R
16 9671962 BRACKE T, MA TIN G 2- 12 D-SA NDER 1 -
4 15 9671961 BRACKE T, SUPPOR T D-SA NDER CLONES 1 -
14 9650360 UNI T TA G, SWA CO NA ME PLATE 1 -
5
1.0 8 25 13 9621380 MA NIF OLD OVERF LOW 2- 12 SLA NT MOU NT D- SANDE R 1
12 9621379 MA NIF OLD, F EE D 2- 12 SLANT MOUNT D-SAN DE R 1 -
17 11 9621289 U-BOLT 7-3/8 I NI D 5/8-1 1 NC X 8- 3/4 IN LG 2 -
B 10 9621280 CLONE A SSY URE THA NE 12I N. G ROOVED E ND 2 -
24
9 5030860 E LBOW GROOVE D E ND90 D SR MI SCH 40 6 I N. 2 -
30 22
16 8 5015031 COUPLI NG GROOVE DE ND BOLT T-GSKT 10 IN 800 PSI 1
S U R F
T B
A C
E
S U
C R
A R
E
L
S
R O U
P N
A
G H N E
S
I S
R
D T H
S A R
P E D G
1 2 5 M I C R
E S
O I N C H
E S M S
R
DR AWN JAM
CH ECKED
T H
O I
L R
E A
D N N
C G
E L
S E
P P
E R O
N C
A
E
J S T
I I O
1 4 . 5 M
Y
N
M- I L. L.C.
59 5 0 N O R T H C
OU RS
E D R IV E ,H O U S T O
N, T EX
AS 7 0 7 2
T O L E
R A
N C E S O N
. X X X = + / - . 0 3 0 0 - 3 0 I
N C H E
S = + / - 1 /
3 2
ENG IN ER
. X X = + / - . 0 6 0 3 0 - 6 0 I
N C H E
S = + / - 1 /
1 6
. X = + / - . 1 0 0 6 0 & O V
E R = + / - 1 /
8
1:2 A N G L
E S + / - 0 ° 3 0
' C H A M & C ' S I
N K S + / - 2 °
APPR OVED
C O N FI D E N TI AL
T H IS DR A W IN G A ND / O R S P E CI CF AI T IO N EM
B O D IE S
MO DEL : PT MONGOOSE
C O N FI DE N T AI LI N F RO M A IT O N O F SW A C O , A D IV SI IO N
O F M -IL . L .C I, N T HE A B ES N C E O F E XPR ES S W R IT E N 2 -1 2 D -S ANDE R AS SEMBLY MU D C LEAN ER
P E R M IS O
N. SW A C O H A S LO A N E D TH IS CO P Y W IT H T HE
NOTES: U N D E RS T A ND IN G T H A T (A) I T W IL LN O T BE R E PR O D U CE D
( B) IT W I L NO T B E U S E D F O R AN Y P UR P O SE E X C EP T
THATFO R W HI CH IT W AS L O A N ED A N D (C ) IT W I L B E SHEE
T S C A LE I ZE
S RA
D W IN G N O . RE
V
SE E SHE E T 2 1 FINISH PA RTS PE R SWA CO E NGINEE RING SPE C SS103 U NLE SS OTHE RWISE SPE C IFIED. R E T UR N E D O N D E M
A NDORUP ONCO M
P L ET IO N O F
Section 9.07
Mongoose Platform Mud Cleaner
2-12 Assembly
Section 9.07
0
19 4 2
1
2-12 Assembly
C 2 SECTION C-C
62.25
28
21
VIEW A-A H
18
21
16 23 3
29
1 15 31 24
26 14
27
21 DETAIL H
27 21 1:2
17 17
DETAIL F
28
22 1:2 21
30
25 21
22
29 21
30 29
24 25
1 24 DETAIL I
DETAIL D
18 1:2
1:2
DETAIL E DETAIL G
M- IL .L . C.
F IL E NAM E: Swac oD 2
D 9672 412
5
3-12 Assembly
Item Part
Description Qty.
Number Number
1 U-Bolt CS 10” Pipe x ¾-10 NC x 13.812 LG with Nut 1289140 2
2 CS U-Bolt 12” Pipe x 7/8-9 NC x 16.06 LG with Nuts 1289171 2
3 Drive Screw #4 x .188 LG, SS 1492031 4
4 Gauge 0-60 PSI (0-400 kPa) 2-1/2” ¼ NPTL M 2422177 1
5 Coupling Grooved End Bolt, T-Gasket 4” 1000 PSI 5015026 3
6 Coupling Grooved 6” 5015029 6
7 Coupling Grooved End Bolt, T-Gasket 10” 800 PSI 5015031 1
8 Coupling Grooved End Bolt, T-Gasket 12” 800 PSI 5015032 1
9 Elbow Grooved End 90D DSR MI SCH 40 6” 5030860 3
10 Clone Assembly Urethane 12” Grooved End 9621280 3
11 U-Bolt 7-3/8” ID 5/8-11NC x 3-3/4” LG 9621289 3
12 Manifold 10” Inlet 3-12 D-Sander Slant Mount 9621325 1
13 Manifold Overflow 12” Slant Mount D-Sander 9621326 1
14 Nameplate ID Product SWACO, 316 SS 9650360 1
15 Bracket, Support D-Sander Clones 9671961 1
16 Bracket, Mating 3-12 D-Sander 9671963 1
17 Weldment, Stand 2-12/3-12 D-Sander Mud Cleaner 9672356 1
18 Stand Leg Weldment, D-Sander 9672361 2
19 Nipple, Groove End Stub 10” 9697001-14 1
20 Nipple, Groove End Stub 12” 9697001-15 1
21 Flat Washer M12 Regular 05-305 48
22 Flat Washer 5/8 N 05-174 6
23 Flat Washer 3/4 N 05-160 4
24 Flat Washer 7/8 N 05-238 4
25 Hex Nut M12 03-415 24
26 Hex Nut 5/8 03-145 6
27 Hex Nut ¾ 03-404 4
28 Hex Nut 7/8 03-405 4
29 HHCS M12 x 35 mm LG 04-1105 4
30 HHCS M12 x 40 mm LG 04-1106 20
31 Split Lock Washer M12 Regular 05-306 24
32 Split Lock Washer 5/8 Regular 05-176 6
33 Split Lock Washer ¾ Regular 05-236 4
34 Split Lock Washer 7/8 Regular 1345397 4
Section 9.07
12 REV DES CRIP TI ON DRAFT ER CHK D AP PRVD DA TE
13
2
3-12 Assembly
17 1
22.0 0
M I L I
E T E R S A R E I
M N B R A
C K E T S DRAWN DEC -0 2-20 05
1:2 D O T
O
N S C A
L E P R
N T S
I
JA M
R E M V
O
E B U R S A N
D S H A R
P E D G E
S
S U R F
C E
A R O
U G H N S
E 1 2 5 M I C R I
O N C H E
S R M S CHECKE D M- IL.L .C.
T O L E
A N C E S P E R A
R N S I 1 4 . 5 M
Y
T H I D
R A N G E
L P R O
E C T I O
J N 595 0NO RTH C
OURSEDRI VE
, HOUSTO
N, TEXAS770 72
T O L E
A N C E S O N
R
. X X X
= + / - . 0 3 0 0 - 3 0 I
N C H E S = + /
- 1 / 3 2
ENGI NEER
. X X = + / - . 1
0 0
6 0 3 0 - &
6 6 0 O
N R
I
E
V C H E S = + /
- 1 / 8
1 6
A N G L
S
E + / - 0 ° 3 0
' C H A M C ' S I N
& K S + /
- 2 °
APPROVED
C O N FID E NT IA L MODEL : MONGOOSE PT PLATFORM
T H IS D R A W IN G A ND / O R S P E IC F ICA T IO N E M B O DIE S
C O N FID E N IT AL I N FO R M A T O
I NOF W
S A C O A, D I V IS O N
OF - IL . L. C. ,I N T HE
M A B SE N C E O F E XP R ES S W TR TI E N
PERM
IS IO N . S W A C O H A S LO A N E D TH IS CO
P Y W IT H TH E
3-12 D-S AN DE R A SSEMB LY C OMMON E ND
U N D ER S T A ND IN G T H A T (A )I T W IL L NO T B ER E P R O
DUCED
NOTES: (B ) IT W I L N O T B E U S E D F O R A NY P U RP O S E EX C E P T
T H A T FO R W H IC H IT W AS L O A N E DA N D ( C) IT W IL B E SHEET SCALE SIZE DRAW INGNO. EV
R
R E TU R N E D O
ND EM
ANDORUPONCO M PL ET IO N O F
B 1 FINISH PARTS PER SWACO ENGINEER ING SPEC SS103 UNLESS OTHERWISE SPEC IFIED. T H E C O N TR A C TE D W O R K, W H IC H E V E R CO M E SF IR S T .
7
8
D
12 H J
2 I
19 1
C
VIEW B-B SECTION C-C
16
17
15 21
3
29
14
29 21
17
24
22 23
33 34
32 21 28
26 31 27
11 25 2
1 DETAIL I
25 31
21 D ETAIL J 1:2
DETAIL D DETAIL H 1:2 M -I L .L . C.
A M E: Swac o D 2
1:2 CALE
S SHEET SI ZE DRAWING NO. RE V
1/8 2of 2 -
F IL E N
1:2 D 967246 1
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Hex Nut 5/8 1305041 8
2 Flat Washer 5/8” N Type A 1345041 16
3 Split Lock Washer 5/8 1345344 8
4 HHCS 5/8 x 2.000 LG 1407139 8
5 Drive Screw #4 x .188 LG, SS 1492031 4
6 Gauge 0-60 PSI (400 kPa) 2-1/2” ¼ NPT LM 2422177 1
7 Gasket, Ring ANSI Flange RF, 150 lb. 10” 3916067 1
8 Bushing Pipe Hex Galv 150 lb. ½ NPT x ¼ NPT 5008417 1
9 Cap Grooved End 6” 5010134 1
10 Coupling, Grooved 6” 5015029 2
11 Coupling Grooved End Bolt T-Gasket 8” 800 PSI 5015030 1
12 Coupling Grooved End Snap T-Gasket 2” 300 PSI 5015052 32
13 Coupling Grooved End Snap T-Gasket 2-1/2” 300 PSI 5015053 8
14 Plug Pipe Sq. HD Galv 1 NPT 150 lb. 5068261 2
15 Decal, M-I SWACO 17-1/2” x 4-1/2” 8420207 1
16 Clone Twin 4” Urethane ½” APEX 9622220 8
17 Manifold Overflow D-Silter 8T4/ALS Mud Cleaner 9622485 1
18 Elbow Grooved End 90° Poly 9622582 16
19 Manifold D-Silter 2-12/8T4/ALS II Mud Cleaner 9622605 1
20 Nameplate ID Product SWACO, 316SS 9650360 1
21 Cover M5 Weld Flange 10” 9671652-01 1
22 Bracket, Mount D-Silter Mud Cleaner 9671853 2
23 Plate, Slider Header Box Mud Cleaner 9671941 1
24 Weldment, Header Box without Flange – Mud Cleaner 9672341 1
25 Weldment, Leg Mud Cleaner Header Box 9672351 1
26 Weldment, Leg Mud Cleaner Header Box 9672352 1
27 Plate, Leg Weldment Header Box Mud Cleaner 9672353 1
28 Plate, Leg Weldment Header Box Mud Cleaner 9672354 1
29 Weldment, Trough 2-12 D-Sander Mud Cleaner 9672366 1
30 Nipple, Grooved End Stub 6” 9697001-12 1
31 Nipple, Grooved End Stub 8” 9697001-13 1
32 Label “Not A Lifting Point” BM6K80122 6
33 Flat Washer M12 Narrow 05-305 108
34 Flat Washer M24 Regular 05-305 24
35 Hex Nut M12 03-415 54
36 Hex Nut M24 03-412 12
37 HHCS M12 x 35 mm LG 04-1105 32
38 HHCS M12 x 40 mm LG 04-1106 22
39 HHCS M24-30 x 90 MM, Yellow Chromate Plated 1493003 12
40 Cover, Plug-1/0 6” Dia. Nitrile S48K00827-NL 2
41 Split Lock Washer M12 Regular 05-306 54
42 Split Lock Washer M24 05-309 12
24
H 41 35
33 37
33
33
41 23
37 35
SECTION E-E
43.21
C
42 SPLITLOCK_M 24 SPLIT LOCK WASHER M24 12 05- 309 -
41 SPLITLOCK_M 12 SPLIT LOCK WASHER M1 2 REGULAR 54 05- 306 05-382
DETAIL C
4 40 S48K00827-NL COVER, PLUG- I\O 6 INC H DIA NITRILE 2 - -
2
1:4 39 HHCS_M24X90MM HHCS M24-3. 0 X 90M M, YELLOW CHR OMATE P LATED 12 - 1493003
17
A 38 HHCS_M12X40MM HHCS M12 X 40mm LG 22 04- 1106 04-11 10
19
37 HHCS_M12X35MM HHCS M12 X 35mm LG 32 04- 1105 04-1746
3
33 33 A 1 36 HEX NUT_M24 HEX NUT M24 12 03- 412 -
41 37 42 D APPLY LOCTI TE 35 HEX NUT_M1 2 HEX NUT M12 54 03- 415 03-230
35 34 36
(N OANTI- SEIZ E) APPLY LOC TITE
(NO ANTI-SEIZE) 34 FLATWSH R_M24 FLA TWASHER M24 REGU LAR 24 05- 308 -
33 FLATWSH R_M12 FLA TWASHER M12 NARROW 108 05- 305 05-281
4 32 BM6_80122 LABEL "NOT A LIFTING PO INT" 6 - -
24 34 7 2 31 9697001- 13 NIPPLE, GRO OVED END STUB8 IN 1 - -
21 35
39 SECTION A-A
35 41 13 30 9697001- 12 NIPPLE, GRO OVED END STUB6 IN. 1 - -
41 1:4 3
33 29 9672366 WELDMENT, TROUGH 2- 12D- SANDER M UDCLE ANER 1 - -
33
26 25 1 28 9672354 PLATE, LEG WELDMENTHEADER BOXM UD CLE ANER 1 - -
33 22
33 28 38
22
37 27 9672353 PLATE, LEG WELDMENTHEADER BOXM UD CLE ANER 1 - -
SECTION B-B DETAIL D SECTION J-J 11 DETAIL H
16 31 26 9672352 WELDMENT, LEG MUD CLEANER HEADERBOX 1 - -
17 1:8
1:4 12 B 25 9672351 WELDMENT, LEG MUD CLEANER HEADERBOX 1 - -
24 9672341 WELDMENT, HEADER BOX W/O FLANGE - M UD CLEANER 1 - -
18 12 18
10 19 23 9671941 PLATE, SLIDERHEADER BOX MUD CLE ANER 1 - -
12 30 22 9671853 BRACKET, M OUNT D- SILTER MUD CLEANER 2 - -
29 32
16 10. 25 21 9671652- 01 COVER, MS WELD FL ANGE 10" 1 - -
6 20 9650360 NAMEPLA TE IDP RODU CT SW AC O, 316 SS 1 - -
19 9622605 MANIFOLDD-SILTERINLET 212 /8T4/ALS IIM UD CLEANER 1
22 8
22 18 9622582 ELBOW GROOVED END 90D POLY 16 - -
17 9622485 MANIFOLDOVERFLOW D-SILTER 8T4/A LS MU D CLEANER 1
22
32 16 9622220 CLONE TWIN 4IN URETHANE1 /2IN APEX 8 - -
22
16 15 8420207 DECAL, M- ISW ACO 17- 1/2" X 4- 1/2" 1 - -
26
14 5068261 PLUG PIPE SQ HD G ALV 1 NPT150 LB 2
13 5015053 COUPLING GROO VED END SNAP T- GSKT 2- 1/2 IN300 PSI 8 - -
32 40
29
12 5015052 COUPLING GROO VED END SNAP T- GSKT 2 IN 300 PSI 32 - -
E E 37
11 5015030 COUPLING GROO VED END BOLTT- GSKT 8 IN 800 PSI 1
J J 14
10 5015029 COUPLING, GROOVED6 IN 2 - -
5 15 9
9 50101 34 CAPGRO OVED END 6 IN 1 - -
20 87.4 10
8 5008417 BUSHING PIPE HEX GALV 150LB 1 /2 NPTX 1 /4 NPT 1
61. 22
7 3916067 GASKET, RING ANSI FLANGERF, 150 LB, 10" 1 - -
33 41 35 24
33 6 2422177 GUAGE0- 60 PSI/0-400 KPA 2- 1/2 IN1 /4 NPTL M 1
5 1492031 DRIVESCREW #4 X .1 88 LG., SS 4 - -
4 14071 39 HHCS 5/8X 2.000 LG. 8 - -
37 33
3 1345344 SPLIT LOCK WASHER 5 /8 8 - -
K 2 1345041 FLA TWASHER 5/8N T YPE A 16 - -
SECTION K-K 27. 37 1 1305041 HEX NUT 5/8 8 - -
35 41 33 33 37
38 K 1:8 tI em Par tNumber Description Quantity 304SST MS
Number
38
24
33
21
25 26
B 28 G 33
27
DETAIL I 41
10. 41 35 M -I L .L . C.
I DETAIL G 595 0 NORT HCOURSE DRI VE , HOUS TON , T E XA S 7 70 72
SHEET
1:4 SCALE SIZE DRAW INGNO. RE V
1/8 2of 3
F IL E NAM E: Sw aco D 2
1:4 D 9672456 A
Section 9.08
Document Title: D-Silter Assemblies
Mongoose PT Platform Mud Cleaner
8T4 Assembly
8T4 Assembly
Item Part
Description Qty.
Number Number
1 Hex Nut 5/8 1305041 8
2 Flat Washer 5/8” N Type A 1345041 16
3 Split Lock Washer 5/8 1345344 8
4 HHCS 5/8 x 2.000 LG 1407139 8
5 Drive Screw #4 x .188 LG, SS 1492031 4
6 Gauge 0-60 PSI (400 kPa) 2-1/2” ¼ NPT LM 2422177 1
7 Gasket, Ring ANSI Flange RF, 150 lb. 10” 3916067 1
8 Bushing Pipe Hex Galv 150 lb. ½ NPT x ¼ NPT 5008417 1
9 Cap Grooved End 6” 5010134 1
10 Coupling, Grooved 6” 5015029 2
11 Coupling Grooved End Bolt T-Gasket 8” 800 PSI 5015030 1
12 Coupling Grooved End Snap T-Gasket 2” 300 PSI 5015052 32
13 Coupling Grooved End Snap T-Gasket 2-1/2” 300 PSI 5015053 8
14 Plug Pipe Sq. HD Galv 1 NPT 150 lb. 5068261 2
15 Decal, M-I SWACO 17-1/2” x 4-1/2” 8420207 1
16 Clone Twin 4” Urethane ½” APEX 9622220 6
17 Manifold Overflow D-Silter 8T4/ALS Mud Cleaner 9622485 1
18 Elbow Grooved End 90° Poly 9622582 12
19 Manifold D-Silter 2-12/8T4/ALS II Mud Cleaner 9622605 1
20 Nameplate ID Product SWACO, 316SS 9650360 1
21 Cover M5 Weld Flange 10” 9671652-01 1
22 Bracket, Mount D-Silter Mud Cleaner 9671853 2
23 Plate, Slider Header Box Mud Cleaner 9671941 1
24 Weldment, Header Box without Flange – Mud Cleaner 9672341 1
25 Weldment, Leg Mud Cleaner Header Box 9672351 1
26 Weldment, Leg Mud Cleaner Header Box 9672352 1
27 Plate, Leg Weldment Header Box Mud Cleaner 9672353 1
28 Plate, Leg Weldment Header Box Mud Cleaner 9672354 1
29 Weldment, Trough 2-12 D-Sander Mud Cleaner 9672366 1
30 Nipple, Grooved End Stub 6” 9697001-12 1
31 Nipple, Grooved End Stub 8” 9697001-13 1
32 Label “Not A Lifting Point” BM6K80122 6
33 Flat Washer M12 Narrow 05-305 108
34 Flat Washer M24 Regular 05-305 24
35 Hex Nut M12 03-415 54
36 Hex Nut M24 03-412 12
37 HHCS M12 x 35 mm LG 04-1105 32
38 HHCS M12 x 40 mm LG 04-1106 22
39 HHCS M24-30 x 90 MM, Yellow Chromate Plated 1493003 12
40 Cover, Plug-1/0 6” Dia. Nitrile S48K00827-NL 2
41 Split Lock Washer M12 Regular 05-306 54
42 Split Lock Washer M24 05-309 12
43 Cap, Victaulic, 2” Dia. 02-420 4
44 Cap, Victaulic, 2.5” Dia. 5010111 2
23
17
43.21 4
2 DETAIL R
1:5
2
3
44 5010111 CAP, VICTAULIC, 2.5" DIAMETER 2 -
1 19
43 02-420 CAP, VICTAULIC, 2"DI AMETER 4 -
F 4 42 SPLIT LOCK_M24 SPLIT LOCKW ASHER M24 12 05-309 -
R
F 2 41 SPLIT LOCK_M12 SPLIT LOCKW ASHER M12 REGULAR 54 05-306 05-382
T 40 S48K00827-NL COVER, PLUG- I\O 6 INCHDIA NITRILE 2 - -
36
42 13
2 39 HHCS_M24X90MM HHCSM 24-3.0 X 90 MM, YELLOW CHROM ATE PLATED 12 - 1493003
34
3 38 HHCS_M12X40MM HHCSM 12 X40mm LG 22 04-1 106 04-11 10
1 37 HHCS_M12X35MM HHCSM 12 X35mm LG 32 04-1 105 04-1746
DETAIL Q
35 36 HEXNUT_M24 HEX NUT M24 12 03-41 2 -
34
1:5 10
21 41 35 HEXNUT_M 12 HEX NUT M1 2 54 03-41 5 03-230
39
SECTION F-F 7 33 34 FLATWSHR_M24 FLAT WASHER M24 REGULAR 24 05-308 -
37 33 33 41 35
9
33 FLATWSHR_M12 FLAT WASHER M1 2N ARROW 108 05-305 05-281
SECTION P-P 33
22 32 BM6_801 22 LABEL"NO TA LIFTING POINT" 6 - -
SECTION N-N 31 9697001- 13 NIPPLE, GROOVED END STUB 8IN 1 - -
37 3333 41 35 1:8 30 9697001- 12 NIPPLE, GROOVED END STUB 6 IN. 1 - -
DETAIL T 29 9672366 WELDM ENT, T ROUGH 2-12 D- SANDER M UD CLEANER 1 - -
12 17 16 18
11
1:4 43 31
SECTION S-S 28 9672354 PLATE, LEG WELDMENT HEADERB OXM UD CLEANER 1 - -
P 27 9672353 PLATE, LEG WELDMENT HEADERB OXM UD CLEANER 1 - -
44
26 9672352 WELDM ENT, LEG MUD CLEANER HEADER BOX 1 - -
30 10 19
25 9672351 WELDM ENT, LEG MUD CLEANER HEADER BOX 1 - -
29 32 24 9672341 WELDM ENT, HEADERBOX W/O FLANGE - M UD CLEANER 1 - -
10. 25 23 9671 941 PLATE, SLIDER HEADER BOX MUD CLEANER 1 - -
22 9671 853 BRACKET, MO UNTD-SILTER MU D CLEANER 2 - -
6
21 9671 652-01 COVER, MS WELD FLANGE1 0" 1 - -
8
20 9650360 NAMEPLATE ID PROD UCTSW ACO, 316 SS 1 - -
22
12 32 19 9622605 MANIF OLD D-SILTER IN LET21 2/8T4/ALS IIM UD CLEANER 1
32
18 9622582 ELBOW GROOVED END 90D POLY 12 - -
22 26
14 17 9622485 MANIF OLD OVERFLOWD- SIL TER8 T4/A LS MUD CLE ANER 1
16 16 9622220 CLONETWIN 4 INURETHANE 1/2 IN APEX 6 - -
15 8420207 DECAL, M- I SW ACO 1 7-1/2" X 4-1/2" 1 - -
15
5 N N 40 14 5068261 PLUG PIPESQ HD GALV 1 NPT 150 LB 2
71. 47
87. 4 13 5015053 COUPLING GROOVEDENDSNAP T- GSKT2- 1/2 IN 300 PSI 8 - -
41 S
20 33 24 10 61. 22 12 5015052 COUPLING GROOVEDENDSNAP T- GSKT2 IN 300 PSI 28 - -
33
11 5015030 COUPLING GROOVEDENDBOLT T- GSKT 8 IN 800 PSI 1
35 10 5015029 COUPLING, GROOVED 6 IN 2 - -
37
S 9 5010134 CAPGROOVED END 6 IN 1 - -
33
8 500841 7 BUSHING PIP E HEX GALV 15 0 LB 1 /2 NPT X 1/4 NPT 1
M 27.3 7
SECTION M-M 37 7 3916067 GASKET, RING ANSI FLANGE RF, 150LB, 10" 1 - -
6 2422177 GUAGE 0-60 PSI/0- 400 KPA2-1/2 IN 1 /4 NPT LM 1
M 1:8
5 1492031 DRIVE SCREW #4 X . 188 LG. , SS 4 - -
35 DETAILO
38 M- I L. L.C.
DETAIL L 1:4 595 0 NORT HCOURS E DRIV E , HOUS T ON, TE XA S 7 70 72
SCALE SHEET SI ZE DRAWI NGNO. REV
Section 9.08
Document Title: D-Silter Assemblies
Mongoose PT Platform Mud Cleaner
8T4 Assembly
6T4 Assembly
Item Part
Description Qty.
Number Number
1 Hex Nut 5/8 1305041 8
2 Flat Washer 5/8” N Type A 1345041 8
3 Split Lock Washer 5/8 1345344 8
4 HHCS 5/8 x 2.000 LG 1407139 8
5 Drive Screw #4 x .188 LG, SS 1492031 4
6 Gauge 0-60 PSI (0-400 kPa) 2-1/2” ¼ NPTL M 2422177 1
7 Gasket, Ring ANSI Flange RF, 150 lb. 10” 3916067 1
8 Bushing Pipe Hex Galv. 150 lb ½ NPT x ¼ NPT 5008417 1
9 Cap Grooved end 6” 5010134 2
10 Coupling, Grooved 6” 5015029 3
11 Coupling Grooved End Bolt T-Gasket 8” 800 PSI 5015030 1
12 Coupling Grooved End Snap T-Gasket 8” 800 PSI 5015030 24
13 Coupling Grooved End Snap T-Gasket 2-1/2” 300 PSI 5015053 6
14 Plug Pipe Sq. GD Galv. 1 NPT 150 lb. 5068261 2
15 Decal, M-I SWACO 17-1/2” x 4-1/2” 8420207 1
16 Clone Twin 4” Urethane ½” APEX 9622220 6
17 Manifold Inlet 6T4 D-Silter 9622491 1
18 Manifold Overflow 6T4 D-Silter 9622492 1
19 Elbow Grooved End 900 Poly. 9622582 12
20 Nameplate ID Product SWACO, 316 SS 9650360 1
21 Cover, M5 Weld Flange 10” 9671752-01 1
22 Bracket, Mount D-Silter Mud Cleaner 9671853 2
23 Plate, Slider Header Box Mud Cleaner 9671941 1
24 Weldment, Header Box without Flange – Mud Cleaner 9672341 1
25 Weldment, Leg Mud Cleaner Header Box 9672351 1
26 Weldment, Leg Mud Cleaner Header Box 9672352 1
27 Plate, Leg Weldment Header Box Mud Cleaner 9672353 1
28 Plate, Leg Weldment Header Box Mud Cleaner 9672354 1
29 Weldment, Trough 2-12 D-Sander Mud Cleaner 9672366 1
30 Nipple, Grooved End Stub 6” 9697001-12 1
31 Nipple, Grooved End Stub 8” 9697001-13 1
32 Label, “Not A Lifting Point” BM6K80122 4
33 Flat Washer M12 Regular 05-305 106
34 Flat Washer M24 Regular 05-308 24
35 Hex Nut M12 03-415 53
36 Hex Nut M24 03-412 12
37 HHCS M12 x 35 mm LG 04-1105 31
38 HHCS M12 x 40 mm LG 04-1106 22
39 HHCS M24-30 x 90 mm Yellow Chromate Plated 1493003 12
40 Cover, Plug1/0 6” Dia. Nitrile S48k00827-NL 2
41 Split Lock Washer M12 Regular 05-306 53
42 Split Lock Washer M24 05-309 12
37 29 24 ASSEMBLYN OTE:
33 24 26 FEED ITEM 2 3THR OUGH SLO T ON BACK OFHEADER BOX;
E OVER SUPPORT GUIDE; OVER BYPASSTROUGH AS SHOWN.
21 S U R F
C E
A R O U
G H N E
S S 1 2 5 M I C R O I
N C H E S R M S CHECKE D
T H
O I
L R
A A
E
D N N
C G
E L
S E
P P
E R O
A E
J S T
N
C I I O
Y N
4 . 5 M
1
M- I L. L.C.
T O L E
A N C E S O N
R
5950NORTH C
OU R
SE DR
I VE,HOUSTON,TEXAS770 72
25 26 . X X X
= + / - . 0 3 0 0 - 3 0 C H E S =
N
I + / -
1 / 3 2 ENGI NEER
. X X = + / - . 0 6 0 0 - 6 0
3 C H E S =
N
I + / -
1 / 1 6
. X = + / - . 1 0 0 0
6 & O V
R
E = + / -
1 / 8 FULL FLOW SEPARATOR
B 28 G 33 A N G L
S
E + / - 0 ° 3 0
' H A M
C & C
' S I N K
S + / -
2 °
APPROVED
27 C O N FI D E N TI AL
41 T H IS D R A W IN G A N D/ O R SP E C IF IC AT IO N E M B O DIE S MODEL : PT MONGOOSE
C O N FI DE N TI A LI N F O RM A T IO N O F S W A C O , AD I V IS IO N
D ETAIL I 10. 41 35 OF M - IL . L. C. ,I N T H E A B S EN C E O F E XP R ES S W TR TI E N
P E RM
IS I O
N. SW A C O H A S LO A N E D T HIS C O PY W IT H TH E D- SILTER ASSY 6 T4 2-1 2 HEADER BOX
1:4 I DETAIL G U N D ER S T A ND IN G T HA T (A ) IT W IL L NO T B E RE P R O DU C E D
( B) IT W I L NO T B E U S E D F O R A N Y P U R PO S E E XC E P T
SHEET SCALE SIZE DRAW INGNO. REV
T HA T F O
RW HI CH IT W AS LO A N E D AN D ( C) IT W IL LB E
R E T UR N E D O N D E M AN D O R U P O N CO M P LET IO N O F
T H E C O N TR AC TE D W O R K ,W H IC H EV E R C O
M E S FI RS T . 1 o f 1 1/8
Section 9.08
Document Title: D-Silter Assemblies
Mongoose PT Platform Mud Cleaner
6T4 Assembly
6T4 Assembly
Item Part
Description Qty.
Number Number
1 Hex Nut 5/8 1305041 8
2 Flat Washer 5/8” Type A 1345041 8
3 Split Lock Washer 5/8 1345344 8
4 HHCS 5/8 x 2.000 LG 1407139 8
5 Drive Screw #4 x .188 LG, SS 1492031 4
6 Gauge 0-60 PSI (0-400 kPa) 2-1/2” ¼ NPTL M 2422177 1
7 Gasket, Ring ANSI Flange RF, 150 lb. 10” 3916067 1
8 Bushing Pipe Hex Galv. 150 lb. ½ NPT x ¼ NPT 5008417 1
9 Cap Grooved End 6” 5010134 2
10 Coupling, Grooved 6” 5015029 3
11 Coupling Grooved End Bolt T-Gasket 8” 800 PSI 5015030 1
12 Coupling Grooved End Snap T-Gasket 2” 300 PSI 5015052 24
13 Coupling Grooved End Snap T-Gasket 2-1/2” 300 PSI 5015053 6
14 Plug Pipe Sq. HD Galv. 1 NPT 150 lb. 5068261 2
15 Decal, M-I SWACO 17-1/2” x 4-1/2” 8420207 1
16 Clone Twin 4” Urethane ½” APEX 9622220 6
17 Manifold Inlet 6T4 D-Silter 9622491 1
18 Manifold Overflow 6T4 D-Silter 9622492 1
19 Elbow Grooved End 900 Poly 9622582 12
20 Nameplate ID Product SWACO, 316 SS 9650360 1
21 Cover, MS Weld Flange 10” 9671652-01 1
22 Bracket, Mount D-Silter Mud Cleaner 9671853 2
23 Plate, Slider Header Box Mud Cleaner 9671941 1
24 Plate, Cover D-Silter PT Mongoose 9671968 1
25 Weldment, Header Box without Flange – Mud Cleaner 9672341 1
26 Weldment, Leg Mud Cleaner Header Box 9672351 1
27 Weldment, Leg Mud Cleaner Header Box 9672352 1
28 Plate, Leg Weldment Header Box Mud Cleaner 9672353 1
29 Plate, Leg Weldment Header Box Mud Cleaner 9672354 1
30 Nipple, Grooved End Stub 6” 9697001-12 1
31 Nipple, Grooved End Stub 8” 9697001-13 1
32 Label “Not A Lifting Point” BM6K80122 4
33 Flat Washer M12 Regular 05-305 106
34 Flat Washer M24 Regular 05-308 24
35 Hex Nut M12 03-415 53
36 Hex Nut M24 03-412 12
37 HHCS M12 x 35 mm LG 04-1105 31
38 HHCS M12 x 40 mm LG 04-1106 22
39 HHCS M24-3.0 x 90 mm, Yellow Chromate Plated 1493003 12
40 Cover, Plug I/0 6” Dia. Nitrile S48k00827-NL 2
41 Split Lock Washer M12 Regulard 05-306 53
42 Split Lock Washer M24 05-309 12
E 37 24 25 ASSEMBLY NOTE:
33 25 27 FEED ITEM 23 THR OUGH SLOT ON BACK OF HEADER BOX;
OVER SUPPOR TGU IDE; OVERB YPASS TROUGH AS SHOWN .
26 33 M I L I
D O
M E
T E R S A R E I N B R A C
O T S C A L
N E P R
I N
T S
K E T S D RAWN J AM De c-1 9-2 0 05
R E M O
V E B U R R
S A N
D S H A R P E D G E
S
21 S U R F
A C
E R O U
G H N E
S S 1 2 5 M I C R O
I N C H E
S R M S C HECKE D
T O L E
R A
N C E S P E R A N
S I Y 1
4 . 5 M M- I L.L .C.
T H I R
D A N G L E P R O
J E
C T I O N
T O L E
R A
N C E S O N
595 0NORTHCOURSEDRIVE, HOU
STON, TEXAS77072
26 . X X X = + / - . 0 3 0 0 - 3 0 I
N C H E S = + /
- 1 / 3 2 EN GINE ER
. X X = + / - . 0 6 0 0 - 6 0 I
3 N C H E S = + /
- 1 / 1 6
. X = + / - . 1 0 0 0
6 & E R
V
O = + /
- 1 / 8
B 33 A N G L
E S + / - 0 ° 3 0
' H A M
C C ' S I N
& K S + /
- 2 ° APPR OVED
28 29 G C O N F ID E N TI AL
MODEL : MONGOOSE PLATFORM
41 T H IS DR A W IN G A N D/ O R SP E C IF ICA T IO N E MB O
D IE S
C O N F IDE N T IA LI N F O RM A T IO N O F SW A C O ,A D I V IS O N
DETAIL I 10.41 35 O F M -IL . L .C ,I N T H E A B S EN C E O F E XP R ES S W RIT T E N
P E R M IS O N. SW A C O H A S LO A N E D TH IS CO
P Y W IT H T H E
D-SILTER ASSY 6T4 HEADER BOX
1:4 I DETAIL G U N D E SR T A DN IN G T AH T A( ) TI W IL L NO T B ER E P R O
( B) TI W I L O
DUCE D
N T B E U S E D F O R A YN P U PR O S E XE C E P T
SHEET SCALE SIZE DRAWI NGNO. REV
T HA T F O R W HI CH IT W AS LO A N E DA N D ( C) IT W IL B E
R E T UR N E D O N D E M AN D O R U P O N C O M PL ET IO N O F
T HE CO N T R AC TE D W O R K ,W H IC H E V E R CO M E SF IR S T. 1o f 1 1/8
Section 9.08
Document Title: D-Silter Assemblies
Mongoose PT Platform Mud Cleaner
6T4 Assembly
10T4 Assembly
Item Part
Description Qty.
Number Number
1 Weldment, Header Box without Flange – Mud Cleaner 9672772 1
2 Plate, Leg Weldment Header Box Mud Cleaner 9672353 1
3 Plate Leg Weldment Header box Mud Cleaner 9672354 1
4 Weldment, Leg Mud Cleaner Header Box 9672773 1
5 Weldment, Leg Mud Cleaner Header Box 9672664 1
6 Weldment, Trough 3-12 D-Sander Mud Cleaner 9672397 1
7 Support, D-Silter 9672779 2
8 Plate, Cross Member 10T4 D-Silter 9672670 1
9 Label, “Not A Lifting Point” BM6K80122 4
10 Cover, MS Weld Flange 10” 9671652-01 1
11 Flat Washer M24 Regular 05-308 24
12 Split Lock Washer M24 05-309 12
13 Hex Nut M24 03-412 12
14 HHCS M24-3.0 x 90 mm, Yellow Chromate Plated 1493003 12
15 Cover, Plug-I/O 6” Dia. Nitrile S48k00827-NL 2
16 Flat Washer M12 Narrow 05-305 122
17 Split Lock Washer M12 Regular 05-306 61
18 Hex Nut M12 03-415 61
19 HHCS M12 x 35 mm LG 04-1105 23
20 Plate, Slider Header Box Mud Cleaner 9671941 1
21 HHCS M12 x 45 mm LG 04-1270 32
22 HHCS M12 x 40 mm LG 04-1106 6
23 Plug Pipe Sq. HD Glav. 1 NPT 150 lb. 5068261 2
24 Nameplate ID Product SWACO, 316 SS 9650360 1
25 Drive Screw #4 x .188 LG, SS 1492031 4
26 Decal, M-I SWACO 17-1/2” x 4-1/2” 8420207 1
27 Manifold, Feed, without Flange 10T4 D-Silter 9622591 1
28 Manifold Overflow 10T4 D-Silter 9622585 1
29 Coupling Grooved End Snap T-Gasket 2” 300 PSI 5015052 40
30 Clone Twin 4” Urethane ½” APEX 9622220 10
31 Elbow D-Silter 10T4, D-Silter Poly 2” Grooved End 9622595 20
32 Coupling Grooved End Snap T-Gasket 2-1/2” 300 PSI 5015053 10
33 Gauge 0-60 PSI (0-400 kPa) 2-1/2” ¼ NPT LM 2422177 1
34 Cap Grooved End 8” 5010135 1
35 Coupling Grooved End Bolt T-Gasket 8” 800 PSI 5015030 2
36 Coupling Grooved End Bolt T-Gasket 10” 800 PSI 5015031 1
37 Nipple, Groove End Stub 10” 9697001-14 1
38 Nipple, Grooved End Stub 8” 9697001-13 1
39 Flat Washer 5/8 N Type A 1345041 8
40 Split Lock Washer 5/8 1345344 4
41 HHCS 5/8 x 2.000 LG 1407139 4
42 Hex Nut 5/8 1305041 4
43 Cap Grooved End 6” 5010134 1
44 Gasket, Ring ANSI Flange RF, 150 lb. 10” 3916067 1
45 Coupling, Grooved 6” 5015029 1
46 Bushing Pipe Hex Galv. 150 lb. ½ NPT x ¼ NPT 5008417 1
F EED BYPASSPLATE THRO UGHSLO TON BACK OF HEADER BOX; A ADDED RIN G GASKET F OR RR I NLET CVR AND RDCR FOR G AUGE J HF 8 /1 7/0 6
OVERS UPPORT GUI DE; OVER BY PASS TROU GH AS SHO WN.
BY PASSPLATE SHOU LD SLI DEW I TH OU TI NTERF ERENCE.
APPLY C OMPO UND SEALANT( LOC TI TE) TO THREADS OF IT EM #4
PER ENGI NEERIN G SPECSS1 37.
USE ANTI SEI ZE ( FO OD GRADE ANTI- SEI Z E ( PN/ 511 68) BY LOCTIT E) ON 93.7 5
ALL BOLT THREADSU NLESS O THERWI SESPEC IF I ED.
33
APPLY SUPERFLEX TM RED RTV SI LI CONE ADHESI VE SEALANT BETWEEN
D-SANDER TROUGH AND D-SI LTER TROUGH AS SHOW N. 46* 5008417 BUSHIN G PI PE HEX GALV 150 LB 1/2 NPT X1 /4 NPT 1
45* 5015029 CO UPLI NG, GROOVED 6I N 1 -
44 3916067 GASKET, RI NG ANSI F LANGERF , 150 LB, 10" 1 -
T H IS DR A WIN G A N D/ O R SP E C IF ICA T IO N E M B O D IE S
C O N F IDE N T IA LI N F O RM A T IO N O F SW A C O ,A D I V IS O N
MON GOO SE PT MUD CLEA N ER
O F M -IL . L .C ,I N T H E A B S EN C E O F E XP R ES S WRIT T E N
G P E R M IS O N. SW A C O H A S LO A N E D TH IS C O P Y WIT H T H E
MONGOOSE PT PLATF ORM
U N D E RS T A ND IN G T HA T (A ) IT WIL L NO T B ER E P R O DUCED
FIL E N
ACKNO
W LE D G
E D : _ _ _ _ _ _ _ _ _ D A TE :_ _ _ _ _ _ _ _ _
NEX TAS SY T O PAS SY D 9672661 A
Section 9.08
10T4 Assembly
32
10T4 Assembly
E
34
C F
L SECTION J-J
SECTION D-D K 1:8
B 1:8
SECTION A-A
1:8 18 17 16 16 21 21 16 16 17 18
44
1
41 39 39 40 42
22 16 16 17 18
18 17 1 6 1 6 21
10
20
14 11 11 12 1 3
2
19 16 1 6 1 7 1 8
DETAIL K M- I L .L. C.
DETAIL L 59 50 NORTH COURSEDRIVE, HOUSTO N, TEXAS 7 707 2
A M E: Sw aco D 2
1:4 SCALE SH
EE T SI ZE DRAWI NGNO. RE V
FIL E N
1:4 1/ 10 2 OF 2 D 9672661 A
13
8T4 Assembly
Item Part
Description Qty.
Number Number
1 Hex Nut 5/8 1305041 8
2 Flat Washer 5/8 N Type A 1345041 16
3 Split Lock Washer 5/8 1345344 8
4 HHCS 5/8 x 2.000 LG 1407139 8
5 Drive Screw #4 x .188 LG, SS 1492031 4
6 Gauge 0-60 PSI/0-400 KPA 2-1/2” ¼ NPT LM 2422177 1
7 Gasket, Ring ANSI Flange RF, 150 lb., 10” 3916067 1
8 Bushing Pipe Hex Galv. 150 lb. ½ NPT x ¼ NPT 5008417 1
9 Cap Grooved End 6” 5010134 1
10 Coupling, Grooved 6” 5015029 2
11 Coupling, Grooved End Bolt T-Gasket 8” 800 PSI 5015030 1
12 Coupling, Grooved End Snap T-Gasket 2” 300 PSI 5015052 32
13 Coupling, Grooved End Snap T-Gasket 2-1/2” 300 PSI 5015053 8
14 Plug Pipe Sq. HD Galv. 1 NPT 150 lb. 5068261 2
15 Decal, M-I SWACO 17-1/2” x 4-1/2” 8420207 1
16 Clone Twin 4” Urethane ½” APEX 9622220 8
17 Manifold Overflow D-Silter 8T4/ALS Mud Cleaner 9622485 1
18 Elbow Grooved End 90° Poly. 9622582 16
19 Manifold D-Silter Inlet 2-12/8T4/ALS II Mud Cleaner 9622605 1
20 Nameplate ID Product SWACO, 316 SS 9650360 1
21 Cover, MS Weld Flange 10” 9671652-01 1
22 Bracket, Mount D-Silter Mud Cleaner 9671853 2
23 Plate, Slider Header Box Mud Cleaner 9671941 1
24 Weldment, Trough 3-12 D-Sander Mud Cleaner 9672397 1
25 Weldment, Header box without Flange – Mud Cleaner 9672341 1
26 Weldment, Leg Mud Cleaner Header Box 9672351 1
27 Weldment, Leg Mud Cleaner Header Box 9672352 1
28 Plate, Leg Weldment Header box Mud Cleaner 9672353 1
29 Plate, Leg Weldment Header Box Mud Cleaner 9672354 1
30 Nipple, Grooved End Stub 6” 9697001-12 1
31 Nipple, Grooved End Stub 8” 9697001-13 1
32 Label, “Not A Lifting Point” BM6K80122 4
33 Flat Washer M12 Narrow 05-305 106
34 Flat Washer M24 Regular 05-308 24
35 Hex Nut M12 03-415 53
36 Hex Nut M24 03-412 12
37 HHCS M12 x 35 mm LG 04-1105 31
38 HHCS M12 x 40 mm LG 04-1106 22
39 HHCS M24-3.0 x 90 mm, Yellow Chromate Plated 1493003 12
40 Cover, Plug-I/O 6” Dia. Nitrile S48K00827-NL 2
41 Split Lock Washer M12 Regular 05-306 53
42 Split Lock Washer M24 05-309 12
A 134 50 41 W AS QT Y12 , U PD AT ED DE TA I L H TR 0 2/ 0 7/ 07
H 37 24 25 ASSEMBLY NOTE:
33 2527 FEED ITEM 23THRO UGH SLOT ON BACK OF HEADER BOX;
O VER SUPPORTG UIDE; O VERBYPASSTROUG HAS SHOWN.
E
33 23 ITEM 23 S HOULD SLIDE WITHOU T INTERFERENC E.
8T4 Assembly
15
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Skid Weldment 9672140 1
2 Basket Assembly 9672130 1
3 Plate, Right Indicator 9672371 1
4 Plate, Left Indicator 9672372 1
5 Jack Elevator 9671681 2
6 Indicator Pointer 9671683 2
7 Plate, Spring Mount, Right Side 9672146 1
8 Spring Plate, Left Side 9672147 1
9 Plate, Skid Discharge Top 9672204 2
10 Spacer, Skid Discharge Chute 9672203 2
11 Door, Skid Discharge 9672205 2
12 Bracket T, Shipping Mongoose Platform 9672172 4
13 Spring Coil 7” 9360007 4
14 Flat Washer M12 Narrow 05-305 64
15 Split Lock Washer M12 Regular 05-306 18
16 Hex Nut M12 03-415 20
17 HHCS M12 x 45 mm LG 04-1270 20
18 Flat Washer M8 Regular 05-276 26
19 HHCS M8 x 40 mm LG 04-1175 18
20 Split Lock Washer M8 Regular 05-285 8
21 Washer, .48” ID x .125” OD x .135” Thick BM6S10137-01 4
22 Hex Nut M8 03-232 8
23 Boot, spring 4.83 OD x 4.78 ID x 6.25 LG Nitrile Compound 5804004 4
24 Lock Washer Schnorr M20 Martin #513014 05-244 8
25 Motor Washer BM6S80043-01 16
26 Schrew Hex HD PLT M20-1.5 x 1.20 mm LG Grade 109 1407169 8
27 Nut Hex PLT M20 x 1.5, Grade 10.9 Yellow Chromate PLT 1305055 8
28 Washer, 16 mm Motor 9671682 8
29 Screw Hex HD PLT M16-15 x 100 mm LG Grade 109 1407144 4
30 Lock Washer Schnorr M16 05-248 4
31 Nut Hex PLT M16-1.5, Yellow Chromate PLT, GR 10.9 1305040 4
32 Spring Spool BM6S80290 4
33 Label, Lift Point BM6K80098 4
34 Label, “PE” Protective Earth BM6K80097 2
35 Shipping Bracket Tag F10K19149 4
36 HHCS M12 x 35 mm LG, MS PLT, Grade 10.9 04-1689 16
37 Hex Nut M12 M5 PLT with Nylon Insert 03-439 16
A AD D S H IPP IN G T AG JAM BS C 2 / 20 / 06
B AD D N EW SH IP P ING BR A CK ET HAR D WA RE JAM BS C 3 / 13/ 0 6
NO TE S:
1. INS TALL SH IPPIN G BR AC KETS AF TER FIN AL A SS EMBLY AN D T ES TIN G IS CO MPLET E.
2. US E F OO D GR AD E AN TI-SIEZE (LOC TIT E 51 16 8) O N ALL B OL TS E XCE PT MO TO R
MO U NT IN G HAR DW AR E A ND SH IPPIN G B R ACK ET B OL TS
3. T OR QU E SHIPP ING BR AC KET B OL TS T O 80 FT-LB S
BIL LO FM AT ER I AL
UN LESS OT HER WISE SPE CIF IE D: SIG NATU RES DA TE
D IM E
N S IO N S A
R E IN IN C H E
S
M IL LIM E TE RS A R E IN B
RACK
ETS DRAWN 9/ 21/ 05
DON OT S CA L E P R IN
TS JAM
RE
MOV E B U
RSANDS
HARPE
DGE S
SUR FACE R
UGHNE
O S S 1 25 M IC R O IN C
HESRM
S
CHEC KED M -I L .L. C.
TO L E
RANCESPERA
N S IY 41 .5 M
59 5 0 N O R T H C O U R S E D R I VE , H O U ST O N , T EX A S 7072
TH I R
DANG
L E P R O JE
C T IO N
TO L E
RANC
E S ON: ENGI NEER
.X X X +/ - .05 FR A C +/- 1 /3 2
.X X +/ - . 01 5 AN G + / - 1 / 2 D EG
.X +/ - . 03 1 CO N C EN .0 0 5 D IA
APPRO VED UN FINISH ED U NIT A SSEMBLY
96 72160
-01 MONGOOS E SHAK ERA TEX UNIT, LE SS HEA DE RBOX, MOTORS , ANDCONTROLS 9672140-01 C O NF ID E NT IA L
T HI S D R AW I NG AN D / O R S P E CI CF AI T IO N E M BO D IE S
9672160 MONGOOS E SHAK ERLE SS HEA DER BOX, MOTORS , ANDCONTROLS 96 7214
0 C O NF ID E N TIA L I N FO R M A TI O N O F SW A C O , A D I VIS I O
N
O F M - IL . L.C ., I N TH E A BS E N C E O F E XPR ES S W RIT T E N MONGOOSE PT
P E RM IS IO N . S WA CO H A SL O A N E D TH IS CO P Y WIT H T H E
CONFIGURATION DES CRIP TION SKID U N DE R S T AN D IN G T H A T (A) I T WIL LN O T BE R E P RO D U C E D
(B ) I T WIL L N O T BE U S ED F O R AN Y P UR P O S E X C E P T
SHET S C A LE SI Z E D R A WI N G N O . REV
T H AT FO R WH IC H I T W AS L O A N ED A N D (C ) IT WIL B E
R E TU R N E D O
N D EM A N D O R U P O N C O M P L ET IO N O F
T H E C O N TR A C TE D W O RK , WH IC H E V E R CO M ES F IR S T.
Section 9.09
Document Title: Unfinished Unit Assembly
Mongoose PT Platform Mud Cleaner
Section 9.09
33
D D
ADD H IGH TE MP RE D S ILICO N E B ETW EEN
SU RF ACE S O F SKID W ELD MENT (ITE M # 1) AN D
SPA CE R (I TEM #1 0)
24 25 26 25 27
20 22
18
2 28
29 28
C C 10
5 5
4
3
8
7
A A 14
33 23
G
32
17 14 1 4 1 5 1 6 1 6 1 5 14 14 1 7
17 1 4 1 4 1 5 16
1 6 1 5 1 4 14 17
12 21
15
11
16 17
7
35 SECTION G-G SECTION D-D SECTION A-A
1:4 1:8 1:8
E 16 36 14 16 15 14
F 14 17
6
37 S EE N OT E 3
36
19 13
E 32
H 6. 19
18 12 DETAIL F
1 B B 9 1:4
H 10
34 NU T PAR T O F S KID WE LDMEN T 21 1 7 3 6 37 14 14 36 SEE NO TE 3
9 6 .9 4
SECTION H-H SECTIO N E-E
1:2 1:4
SPR ING B OO T H IDD EN FO R CL AR ITY M -I L .L. C.
A M E: Sw aco D 2
SCALE SHEE T SI ZE DRAWINGNO. RE V
FIL E N
1/ 8 2 OF 2 D 967216 0 B
5
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Weldment, Mongoose Basket 967211-01 1
2 Brace, Sidewall Support 9672116-01 2
3 Motor Tube Weldment 9672120-02 1
4 Cover, Removable 9672167-01 1
5 Bar, Skirt Retainer 9672168 1
6 Plate, Drip Lip Mongoose PT 9672169 1
7 Spring Mount, Basket 9672127 4
8 Weldment, Screen Bar 9671640 4
9 Gasket, Mongoose Flat Panel Screen 5837001 4
10 Skirt, Feed End 5873004 1
11 Wedge, Mongoose Screen Clamping 5895001 8
12 Spring Spool BM6S80290 4
13 Washer .48” ID x 1.25” OD x .135” Thick BM6S10137-01 6
14 Grommet Screw.273 Sq. Panel Hole 07-415 32
15 #8 Flat Head Sheet Metal Screw with Square Drive 1441471 32
16 Hex Nut M20-25 Yellow Chromate Plated 03-435 16
17 HHCS M20-2.5 x 70 mm LG Yellow Chromate Plated 04-1660 16
18 Split Lock Washer M12 Regular 05-306 34
19 Flat Washer M12 Narrow 05-305 100
20 Flat Washer M20 05-296 32
21 Hex Nut M12 03-415 62
22 HHCS M12 x 35 mm LG 04-1105 58
23 HHCS M12 x 45 mm LG 04-1270 4
24 Decal, “Mongoose Shaker” 9650512 2
25 Lock Washer Schnorr M20 Martin #513014 05-244 16
26 Schnorr M12 Lock Washer 05-371 28
1 04 . 39
G G
A A
63 . 00
E E
ISO VIE W
1:10
26 05- 371 SCHNO RR M 12 LO CKW ASHER 28 - =
25 05- 244 LOCKWASHER SCHNORR M20 MARTI N #51301 4 16 - -
24 96505 12 DEC AL, "MO NGOO SE SHAKER" 2 - -
Section 9.10
Document Title: Basket Assembly
Mongoose PT Platform Mud Cleaner
AD D HIGH TE MP RE D
19 1 SIL IC ONE AR OUN D
22 TH E P ERIMET ER OF
TH E R EMOVEA BLE
COV ER
Section 9.10
18 22
22
6 5
1 19
19
18
19 4 4
21
18
21 SE E N OTE 3 10 10
19
21
14 9 8 15
DETAIL D AD D HIG H TEMP RE D
SIL ICONE AR OUN D DETAIL C
1:2 TH E PE RIMET ER OF DETAIL B
TH E R EMOVEAB LE 1:2 1:2
COV ER
22
10
SECTION E-E
22 1:2
13
2 1 18
DETAIL F
19 1:2
21
26 12
19
1 3
SECTION G-G
1:2 11 11 11
3 17 20 25 F
11
C
2 22 19 19 21 SE E N OTE 3
16 SE E N OTE 4 B
20
D
SECTIO N A-A
SECTION H- H
1:2 SECTION J-J
1:4 M-IL .L . C.
5
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
2 Motor Starter Assembly, 440-480V, 60 Hz, UL for
6930025
Assembly 9672301-01
2 Motor Starter Assembly, 380-415V, 50 Hz, UL for
1 6930023 1
Assembly 9672301-02
2 Motor Starter Assembly, 575-600V, 60 Hz, UL for
6930027
Assembly 9672301-03
2 HHCS M10 x 45 mm LG 04-1181 4
3 Flat Washer M10 Regular 05-277 8
4 Split Lock Washer M10 Regular 05-270 4
5 Hex Nut M10 03-229 4
6 Nameplate ID Product SWACO, 316SS 9650360 1
7 Pop Rivet, .125 Dia 07-409 4
NOTES :
1. ITE MS S HOWN MOUNTED T OSHA KERJUST FORREFE RENCE
2. USE FOODG RADE ANT I-SIEZE (L OCTIT E 51168) ON ALL BOLT THRE ADS
5
4
3
B B
3
2
6 7
7
1
1
A 7 7
4 5
6
3 7
STARTER KIT COMPONENTS
7 POP_RIVOT_125 POPRIV OT, .1 25DIA. 4 07-409
6 9650360 NAM EPLATE ID PRODUCT SWACO, 316 SS 1 -
3
5 HEXNUT_M1 0 HEXNUT M10 4 03-229
4 SPLIT LOCK_M10 SPLITL OCK WASHER M10 REGU LAR 4 05-270
2
3 FLATWSHR_M10 FLATW ASHER M10 REGULAR 8 05-277
2 HHCS_M10X45M M HHCS M10 X 45mmLG 4 04-11 81
VIEW B-B DETA IL A 1 SEET ABLE 2 MTR STARTER ASSY 1
1 Ite m Document Number T itle Q uantity 304SST
Number
BIL L OF MAT ERI AL
a c hi n e d
M
9672301-02 69 30023 S TARTER A SS Y 2 MTR, 3 80- 415V , 50HZ, UL . X + -/ . 30 1 C O N CE N . 0 5 D IA APPROVED S TARTER KIT, 2-MOTOR, UL
CONF ID EN T IA L
9672301-01 69 30025 S TARTER A SS Y 2 MTR, 4 40- 480V , 60HZ, UL T HIS DRAWI NG AND/OR SP ECIF ICA T ION EM B ODIE S
CONF ID ENT IA L I NF ORMA T IONOF SW ACO, ADIV IS ION
OF M- IL .L .C ., I NTH EABSEN CEOF EXPR ES SWRIT EN
CONFIGURATION IT EM #1 DES CRIP TION PERMIS ION. SWAC O HA SLOANEDTH IS COPYWIT HT HE
MONGOOS E
UNDE RSTA NDIN GT HAT (A ) IT WIL L NOT BE REPR ODUCE D
A M E: Swa c o D
( B) I T WIL NOTB E US EDF ORANY PUR POSE EXCEP T SH
E ET SCALE SI ZE R A WIN GNO.
D REV
T HAT FORWHIC HIT WAS LOANEDA ND(C ) IT WI L BE
RETU RNED O N DEMAND ORUPONCO M P L ET IONOF
T HECONT RACTED WORK, W H IC HEVERCOMESF IR ST .
F IL E N
ACKN OWLE DGED: _ _ _ _ _ _ _ _ _ DATE :_ _ _ _ _ _ _ _ _ NEX T ASSY T O PAS SY
1 OF 1 1/ 4 D 9 67 2301 A
Section 9.11
Mongoose PT Platform Mud Cleaner
Document Title: Starter Kit
See Drawing(s) at End of Table 2
TABLE 2. PARTS LIST FOR STARTER KITS 9672303-01, -02 & -03
Item Part
Description Qty.
Number Number
3 Motor Starter Assembly, 440-480V, 60 Hz, UL for
6930008
Assembly 9672301-01
3 Motor Starter Assembly, 380-415V, 50 Hz, UL for
1 6930020 1
Assembly 9672301-02
3 Motor Starter Assembly, 575-600V, 60 Hz, UL for
6930024
Assembly 9672301-03
2 HHCS M10 x 45 mm LG 04-1179 4
3 Flat Washer M10 Regular 05-338 8
4 Split Lock Washer M10 Regular 05-306 4
5 Hex Nut M10 30-415 4
6 Nameplate ID Product SWACO, 316SS 9650360 1
7 Pop Rivet, .125 Dia. 07-409 4
A A
6 7
7
7 7
3 5
4
6
7 STARTER KIT COMPONENTS
8 B M6_ 10137 -01 WASHE R, .4 8 " I. D. X 1.2 5" O.D . X . 135" T HIC K 4 - -
8 7 P OP _ RIV E T_ 125 POP RI V ET, .125 DI A. 4 07 -409 07-4 19
a c hi n e d
M
.X + / - . 0 31 CO N CE N . 0 05 D IA AP P R OV E D STAR TE R KIT, 3 MOTOR ,U L
9 672303 -03 693002 4 ST AR TE R A SS Y3 MTR , 575-60 0V , 60 HZ, UL CO NF ID E NTIA L
HT IS DR A WIN G A ND / O R S P EC IF IC AT IO N E MBO DIE S
CO NF IDE NT IAL I NFO RMA TIO N O
F S WA CO,A DI VIS IO N
9 672303 -02 693002 0 ST AR TE R A SS Y3 MTR , 380-41 5V , 50 HZ, UL F M-IL . L. C.,I NT HE A BS E NCE OF E XP RES S WRIT TE N
O
PE RMISI ON. S WA CO HA SL OA NE DT HIS CO P Y WIT HT HE M ONGOOSE
9 672303 -01 693000 8 ST AR TE R A SS Y3 MTR , 440-48 0V , 60 HZ, UL UN DE RS T A NDIN GT HA T (A) IT WI L NO T B ER E P RO DUCE D
B( ) IT WI L NOT B E US ED F O R A NY P URP OS E X CEP T
S HE E T SC
AL E S IZ E R A WIN GN O.
D RE V
TH A T F O R WHI CH IT W AS L OAN E DAN D( C) IT WIL B E
RE T URN E DO N DE M A NDO R UPO N CO MPL ET IO NOF
TH E CO NT RA CTE DW ORK , WHI CH EV E RCO M ES F IR ST .
F IL E NA M E : S wa c o D
NE X T A S S Y T OP A S S Y 1 OF 1 1/8 D 9672303 D
AC K NO
W LE DG E D: _ _ _ _ _ _ _ _ DA TE :_ _ _ _ _ _ _ _ _
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Conduit Locknut ¾-NPT 01-184 3
2 Lock Washer External Tooth 1.00: 05-110 3
3 Cable Gland, ¾” NPT for .62” Dia. Cable 01-1888 6
Motor Cord, UL, 14 GA., .62D, Embroidered Jacket, 50 Feet Length for
7906237 1
Configuration 9672307-01
4
Motor Cord, UL, 14 GA., .62 D, Embroidered Jacket for 60 Feet Length
7906237
for Configuration 9672307-02
5 Cord Grip Straight 01-106 3
6 Clamp Stainless Steel, 3-Hose Clamp 00-1665 4
7 Split Lock Washer M8 Regular 05-285 8
8 Hex Nut M8 03-232 16
9 Elbow Conduit EP90D ¾ MPT x ¾ FPT 5030937 2
10 HHCS M8 x 55 mm LG Full Thread 04-1178 8
11 Bushing Split Nitrile 5/8” Tube .609” ID 7/8” OD 09-814 12
12 Tie Cable 0.30” x 11.50” LG 8087258 6
13 Terminal Wire Ring, 14-18 AWG Wire 6592001 15
A MOTOR CORD PART NUM BER CHANGED (0 1-1885 TO 790623 1) JAM BSC 10/17 /05
B ADDED CONFI GURATIONS - 02 & - 03, CHANGEI TEM #1 3 SAR GMG BSC 01/18/06
C ADDED TABLES2 & 3 FOR C ABLE TIE L OCATI ONS & NO TES 3-5 J HF 4/25/06
D ADDED -04 CON FI GURATIO N JHF 8/2/06
E CHANGED MOTOR COR D7906231 TO 790623 7, ADDED NOTE#6 GMG 1 1/8/06
ELLIPTICAL MOTOR
TOP MOTOR ELL IPTIC AL
MO TOR C OR D
TOP MOTOR
COR D
BOT TOM
MOTOR CORD
BOTTOM MOT OR
CA BLE #3
ISO VIE W - WIRING K IT -01 & -02 CONFIGURATIONS
MOTOR 1:8
REFERENCE - MONGOOSE ASSEMBLY WITH WIRING KIT CON NECTOR
1:10 6
TOWER
CONNECT OR
CABLE #2 FIT CA BLES CLOSE T OI NSIDE CORN ER
OF CA BLE T OWER WELD MEN T
SEE NO TE 6 TI E B
13 6592001 TERMI NAL WIRE RI NG, 14- 18 AWG W IR E 15 -
12 8087258 TI EC ABLE 0.3 0 IN X 11. 50 IN LG 6 -
11 09- 814 BUSHI NG SPLI T NIT RIL E 5/8" T UBE .6 09" I D 7/8" OD 12 -
CABLE #1 TI E C TI E A
10 HHCS_M 8X55M M_FU LL_THD HHCS M8 X55m m LGF ULLTHRE AD 8 04- 1178
9 5030937 ELBOW CONDUI TEP 90D 3/4 M PT X 3/4 FP T 2 -
DETAIL E 8 HEXNUT_M8 HEX NU T M8 16 03-232
1:4 7 SPLI TLOCK_M8 SPLI TLO CKWASHER M8 REGULAR 8 05-285
SE E TAB LE #2 6 00- 1665 CLAMP ST AIN LESS STEEL 3- HOSE CL AM P 4 00- 1665
S EE N O TES 3 & 4
5 01 -106 CORD GRI PS TRAI GHT 3 -
CABLE #3 27 4 SEE TABLE MOTOR CORD, UL, 14G A, .6 2D 1 -
CABLE #2 7 5.5 5.5 25
3 01 -1888 CABLE GLAND, 3 /4" NPT, FOR . 62" DIA CABLE 6 -
CABLE #1 7 5.5 5.5 25
2 05- 110 LOCKWASHER EXTERNAL TO OTH 1. 00" 3 -
TOW ER APPROX. LE NGTHOF CABLE FROM TOW ER
ATO B BTO C
CONNECTOR TO A CONNECT OR TO MOT OR CONNE CTOR 1 01 -184 CONDUI T LOCKNUT 3/4-NPT 3
APP ROXIMATE DISTANCE BE TWE ENCABL E TIES (INCHE S) Item Document Number Ti tle Quan tity 304SST
NO TES : TABL E #2 - PT MONGOOSE Number
BIL LO FM AT ER I AL
1. SH AKER AS SE MB LY SHO W N AS RE FERE NCE T O SHO W W H ERE UN LESS OT HER WISE SPE CIF IE D: SIG NATU RES AD TE
D IM E
N S IO N S A
R E IN IN C H E
S
AL L C OMP ON EN TS OF THE W IR IN G K IT AR E L OC ATE D M IL LIM E TE R
DON OT S C
S A R E IN B
A L E P R IN
TS
RACK
ETS DRAWN JA M 9 /2 8/ 0 5
RE
MOV E B U
RSANDS
HARPE
DGE S
2. ITEM # 1 3 (65 92 00 1) IS N OT SHOW N . TH EY A RE US ED TO SUR FACE R
UGHNE
O S S 1 25 M IC R O IN C
HESRM
S
CHEC KED M -I L .L. C.
967 2307-0
4 WIRIN GK IT, 3 MOTOR, UL 790 623
7 MOTORCORD, UL A PPROV ED, 14 GA. .6 20 IN. DIA . EBMR JA CK ET 30 P AGE 5 TO L E
RANCESPERA
N S IY 41 .5 M
59 5 0 N O R T H C O U R S E D R I VE , H O U ST O N , T EX A S 7072
TH I R
DANG
L E P R O JE
C T IO N
C ON NE CT W IR ES TO TER MIN ALS TO L E
RANC
E S ON: ENGI NEER
967 2307-0
3 WIRIN GK IT, 3 MOTOR, UL 790 623
7 MOTORCORD, UL A PPROV ED, 14 GA. .6 20 IN. DIA . EBMR JA CK ET 75 P AGE 3 .X X X +/ - .05 FR A C +/- 1 /3 2
.X X +/ - . 01 5 AN G + / - 1 / 2 D EG
3. A LL DIMENS IONS FO R CA BLE TIE S AR E u 1" .X +/ - . 03 1 CO N C EN .0 0 5 D IA
APPRO VED
967 2307-0
2 WIRIN GK IT, 3 MOTOR, UL 790 623
7 MOTORCORD, UL A PPROV ED, 14 GA. .6 20 IN. DIA . EBMR JA CK ET 60 P AGE 1 C O NF ID E NT IA L
WIR IN G K IT , 3 MO TOR ,U L
4. A LL DIMENS IONS FO R CA BLE LEN GT HS AR E +1 ", -0 " T HI S D R AW I NG AN D / O R S P E CI CF AI T IO N E M BO D IE S
967 2307-0
1 WIRIN GK IT, 3 MOTOR, UL 790 623
7 MOTORCORD, UL A PPROV ED, 14 GA. .6 20 IN. DIA . EBMR JA CK ET 50 P AGE 1 C O NF ID E N TIA L I N FO R M A TI O N O F SW A C O , A D I VIS I O
N
O F M - IL . L.C ., I N TH E A BS E N C E O F E XPR ES S W RIT T E N
5. C AB LE B UN D LES SHO U LD B E N EATL Y A RR ANG ED W ITH SMOO TH C U RVE S. P E RM IS IO N . S WA CO H A SL O A N E D TH IS CO P Y WIT H T H E M ONGOOSE
CONFIGURATION DESCRIP TION ITEM 4 DES CRIPTION LENGTH (FEET) BOM U N DE R S T AN D IN G T H A T (A) I T WIL LN O T BE R E P RO D U C E D
6. APP LY LOC TIT E # 27 2 TO IT EM #9 W HER E IT CO NN EC TS TO T HE MOT OR HO U SIN G (B ) I T WIL L N O T BE U S ED F O R AN Y P UR P O S E X C E P T
SHET S C A LE SI Z E D R A WI N G N O . REV
T H AT FO R WH IC H I T W AS L O A N ED A N D (C ) IT WIL B E
R E TU R N E D O
N D EM A N D O R U P O N C O M P L ET IO N O F
T H E C O N TR A C TE D W O RK , WH IC H E V E R CO M ES F IR S T.
Section 9.12
Document Title: Wiring Kit/UL Certified
Mongoose PT Platform Mud Cleaner
Section 9.12
12
3
B B
C L INEA R MO TO R CO RD L INEAR MO TO R C O RD
11 7 11 6
8
4 L INEAR MO TO R C AB LES 11
D D 8
12
A
SECTION A-A
1:2
(TYP - 2 PLCS THROUGH SKID)
3
9 11 8 8
11 6
2 5° T YP - B OT H
L IN EAR MO TO RS
1
5 2
1
5
11
E LLIPT ICAL MO TO R CO RD 7 10
L IN EAR MO TO R C O RD
5 1 2
SECTION D-D
2
SECTION C-C 1:2
SECTION B-B 1:4 (TYP - 2 PLCS THROU GH TOW ER)
1:2
M- I L. L.C .
595 0 NORTHCOURSEDRIV E,HOUSTON ,TEXAS 77 072
SCALE SHEET SIZE DR
A WING NO. REV
1/ 12
5
6
C ABLE #2
C ABLE #
SKID
BAC K
CONTROL BOX
CONNECT OR
C ABLE #3
IEB
TIE A
DETAIL F
SEE TABLE #3
SEE NOTES 3 & 4
CAB LE # 3 8 8 24
CAB LE # 2 8 8 24
CAB LE # 1 8 8 24
AP P RO X . L E NGT H OF CAB LE F RO M BACK
S KID TO A A TO B
O F S KI D T O CONT RO L BOX CONNE CT OR
AP P RO X IM AT E DI S TAN CE BE TW E EN CABL E T IE S ( INCHE S )
T ABL E #3 - P T M ONGO O S E
9672307-01 CONFIGURATION
CABLE L AYOUT
M- I L .L. C.
Section 9.12
Document Title: Wiring Kit/UL Certified
Mongoose PT Platform Mud Cleaner
See Drawing(s) at End of Table 2.
TABLE 2. PARTS LIST FOR WIRING KIT 9672307-03
Item Part
Description Qty.
Number Number
1 Clamp Stainless Steel 3-Hose Clamp 00-1665 5
2 Cord Grip Straight 01-106 3
3 Conduit Locknut ¾-NPT 01-184 3
4 Cable Gland, ¾” NPT for .62” Dia. Cable 01-1888 6
5 Lock Washer External Tooth 1.00” 05-110 3
6 Bushing Split Nitrile 5/8” Tube .609” ID 7/8” OD 09-814 15
7 Elbow Conduit EP 90D ¾ MPT x ¾ FPT 5030937 2
8 Terminal Wire Ring, 14-18 AWG Wire 6592001 15
9 Tie Cable 0.30” x 11.50” LG 8087258 4
10 Hex Nut M8 03-232 20
11 HHCS M8 x 50 mm LG 03-232 10
Motor Cord, UL, 14 GA., .62D, Embroidered Jacket, 75 Feet Length for
12 7906237 1
Configuration 9672307-03
13 Split Lock Washer M8 Regular 05-285 10
SEE NO TE
M -I L .L. C.
5 950 NORTHCOURSEDRIVE,HOUSTON ,TEXAS7 7 072
SCALE SHEET SI ZE DRAWI NGNO. RE V
1/ 12
Section 9.12
Document Title: Wiring Kit/UL Certified
Mongoose PT Platform Mud Cleaner
See Drawing(s) at End of Table 3.
TABLE 3. PARTS LIST FOR WIRING KIT 9672307-04
Item Part
Description Qty.
Number Number
1 Elbow Conduit EP 90D ¾ MPT x ¾ FPT 5030937 2
2 Cable Guard, ¾” NPT for .62” Dia Cable 01-1888 6
3 Cord Grip Straight 01-106 3
4 Lock Washer External Tooth 1.00” 05-110 3
5 Conduit Locknut ¾-NPT 01-184 3
6 Clamping Unit, Multi-Clamp, 5/8” OD Hose 00-1604 2
7 Clamping Unit, 5/8” Hose OD, 3 Hose Assembly 00-1614 1
8 Split Lock Washer M8 Regular 05-285 4
10 Hex Nut M8 03-232 4
Motor Cord, UL, 14 GA., .62D, Embroidered Jacket, 30 Feet Length for
11 7906237 1
Configuration 9672307-04
12 Tie Cable 0.30” x 11.50” LG 8087258 3
13 HHCS M8 x 55 mm LG Full Thread 04-1178 8
SE E NO TE 6
S EE N OTE 6
13
13
13
11
7 00- 161 4 CLA MPI NG UNI T, 5/8" HOSE OD, 3H OSE A SSE MBLY 1 -
6 00- 1604 CLA MPI NG UNI T, MULTI- CLAM P, 5/8" OD HOSE 2 -
5 01-184 CONDUIT LOCKNUT 3/4-NPT 3
4 05- 110 LOCKWA SHER EX TE RNAL TOOTH 1.0 0" 3 -
3 01-1 06 CORD GRIP STRA IG HT 3 -
2 01-1888 CA BLE GLA ND, 3 /4" NPT, FOR .6 2" DIA CA BLE 6 -
1 5030937 E LBOWC ONDUI T EP 90D 3/4 MPTX 3/4 FPT 2 -
I tem Document Number T itle Quantity 304SST
Number
M-I L .L. C.
Section 9.12
Document Title: Wiring Kit/UL Certified
Mongoose PT Platform Mud Cleaner
Section 9.12
7 6 13 8 10
2
1
12
2 5° TYP 4
B OT H LINE AR MOTORS 3 5
11
10 8
SECTIO N G-G
1:4
DETAIL L
H H 1:2
G J J
K K
L
M-IL .L . C.
F IL ENA M E: Swaco D 2
6 OF 6 D 9672307 F
11
NOTES:
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
Item Part
Description Qty.
Number Number
1 Plunger, Spring, Knurled Knob, ¾”-10, 316SS 00-1749 1
2 U-Bolt SS 3” Pipe x ½-13 NC Threads Rubber Coated 1289079 2
3 Gasket, Self-Gripping 3914760 16
4 Teflon Rod, 1” Dia., 4.50” Long 56-386-001 2
5 Butt Hinge, 304SS, 6” x 6”, 0.18” Thk. 5845711 2
6 Skirt, Discharge End, Vent Hood 5873006 1
7 Retainer Bar, Skirt Vent Hood 9672959 2
8 Cover Bottom, Motor Tube, Vent Hood 9672978 1
9 Clip Retainer, Skirt, Vent Hood 9672979 1
10 Door Weldment, Screen Wedge Access 9672981 2
11 Lift, Vent Hood Cover, Right Side 9672982 1
12 Lift, Vent Hood Cover, Left Side 9672983 1
13 Plate, Bracket Spring Plunger 9672988 1
14 Cover Plate, Two Motor Vent Hood 9672989 1
15 Locking Plate, Feed End Door 9672991 1
16 Plate, Mount Vent Hood Mud Cleaner 9673001 1
17 Plate, Spacer Mount Vent Hood Mud Cleaner 9673002 2
18 Plate, Mounting Vent Hood Mud Cleaner 9673003 2
19 Weldment, Vent Hood Over Basket Mud Cleaner 9673005 1
20 Weldment, Nut Turnbuckle ½-13 & M12 Threads 9673009 4
21 Weldment, Door Vent Hood Mud Cleaner 9673010 1
22 Weldment, Backwall Cover Vent Hood Mud Cleaner 9673065 1
23 Shipping Bracket Tag F10K19149 2
24 Flat Washer M12 Narrow 05-305 94
25 Flat Washer M8 Regular 05-276 46
26 Hex Nut M12 03-415 50
27 Hex Nut M8 03-232 24
28 HHCS M12 x 30 mm LG 04-1157 14
29 HHCS M12 x 35 mm LG 04-1105 6
30 HHCS M12 x 40 mm LG 04-1106 31
31 HHCS M12 x 45 mm LG 04-1270 8
32 HHCS M8 x 25 mm LG 04-1672 2
33 HHCS M8 x 30 mm LG 04-1131 22
34 Jam Nut ¾ 03-184 2
35 Split Lock Washer M12 Regular 05-306 54
36 Split Lock Washer M8 Regular 05-285 24
Section 9.13
Document Title: Vent Hood Assemblies
Mongoose PT Platform Mud Cleaner
Section 9.13
34 34
15
M I
H
32
M L 2 7 36 2 5 K
14
22 DETAIL 16
1:4 24 17 24 SECTION B-B
27
36 33
26 14
35 22
24 DETA IL I
5
1:2
12 11
DETA IL H SEE NOTE 3
G
19 1:2 24 2 8 19
30
SECTION A-A 24
24
23 23
D OORS NO T SHO W N FO R C LART IY
1:4 6 6 35
7 8
26 30 26 24
35 26
7
CO VER SHOU LD BE P OSITION ED 35 DETAIL J
B SO THA T IT IS CON CEN TRIC 19 DETAIL F
TO THE M O TOR TU BE PIPE 1:2
A 1:2
E 9
D 35
6
E DETAIL G
C 1:2
9
15 31
D 34
34 35
1
18
C 11 2533
8 13
A 19
B 26 2 4
30
20
25
27 SECTION M-M
35 36
19 1:4
2
24
SECTION E-E DE TAIL K
1:2 1:4 M-I L .L . C.
SECTION C-C SECTION D-D
5950NORTHCOURSEDRIVE,HOUSTO N, TEXAS77072
SHEET
SCALE SIZ E DRAWING NO. RE V
1:2 1:4 2OF 2
F IL E NAM E: Swac oD 2
1/8 D 9673000 -
5
See Drawing(s) at End of Table 2
TABLE 2. PARTS LIST FOR VENT HOOD ASSEMBLY 9673015
Item Part
Description Qty.
Number Number
1 HHCS M6 x 16 mm LG 04-1133 40
2 Gasket, Self-Gripping 3914760 41
3 T-Handle, Quarter Turn 304 SS 5845410 2
4 Weldment, Vent Hood 10T4 Mud Cleaner 9673020 1
5 Weldment, Door Vent Hood Mud Cleaner 9673025 1
6 Weldment, Door Vent Hood Mud Cleaner 9673030 1
7 Weldment, Door Vent Hood Mud Cleaner 9673035 2
8 Runner, Door Vent Hood Mud Cleaner 9673036 2
9 Runner, Door Vent Hood Mud Cleaner 9673037 2
10 Plate, Bracket Vent Hood Mud Cleaner 9673038 2
11 Plate, Bracket Vent Hood Mud Cleaner 9673039 2
12 Weldment, Duct Vent Hood Mud Cleaner 9673040 1
13 Weldment, Duct Vent Hood Mud Cleaner 9673045 1
14 Weldment, Duct Vent Hood Mud Cleaner 9673050 2
15 Plate, Sleeve Duct Vent Hood Mud Cleaner 9673051 4
16 Weldment, Cover Lifting Vent Hood Mud Cleaner 9673055 1
17 Weldment, Cover 10T4 Vent Hood Mud Cleaner 9673057 1
18 Weldment, Cover 10T4 Vent Hood Mud Cleaner 9673058 1
19 Weldment, Flange 150 lb. Vent Hood Mud Cleaner 9673060 1
20 Flat Washer M12 Narrow 05-305 52
21 Flat Washer M24 Regular 05-308 8
22 Flat Washer M6 Regular 05-284 40
23 Flat Washer M8 Regular 05-276 40
24 FHSCS M8 x 25 mm LG 04-1655 20
25 Hex Nut M12 03-415 20
26 Hex Nut M24 03-412 4
27 Hex Nut M6 03-236 4
28 Hex Nut M8 03-232 20
29 HHCS M12 x 30 mm LG 04-1157 20
30 HHCS M12 x 40 mm LG 04-1106 16
31 HHCS M24 x 65 mm 04-1712 4
32 HHCS M6 x 20 mm LG 04-1208 4
33 HHCS M8 x 25 mm LG 04-1672 20
34 Round ½ (.500) Dia. x 27.75 LG 56-037-012 2
35 Split Lock Washer M12 Regular 05-306 36
36 Split Lock Washer M24 05-309 4
37 Split Lock Washer M6 Regular 05-269 40
38 Split Lock Washer M8 Regular 05-285 40
REV D E SCR IP TI ON D RA FT ER CH KD AP PR V D D AT E
7
8
7 .63
7.25
6.0 0 31. 62
5
2
28. 12 28.1 2
3
2
LOC ATE ENDSOF
GASKETAS SH OW N 5
C
SECTION C-C ISO VIEW
1:2 1:4
2 25
35
20
5
3 29 2 0
M- I L. L.C.
5950NORTH COURSEDRIVE,HOUSTO N ,TEXAS77072
SHEET
SCALE SI ZE DRAWI NGNO. REV
Section 9.13
Document Title: Vent Hood Assemblies
Mongoose PT Platform Mud Cleaner
Section 9.13
31.0 6
31. 62
ISO VIEW
1:6
25.8 7 26.6 2
1.2 4 .5 6
.5 6
LOCATEENDS OF
LH DOOR ASSEMBLY SECTION A-A 8 RH DOOR ASSEMBLY GASKET AS SHOW N
A
3 4 SE CURE W ITH SET SCREWS
3 4 SE CURE W ITH SET SCREWS
B B
1. 62 1. 76
23
28 38
24 APPLYREMOVABLE LOCTITE T OBOLT
F IL E NAM E: Sw ac o D 2
1/6 3 OF 6 D 9673015 -
9
10
27
32
77.37 33.7 4
4. 38 73.00
D
E 16 .6 8
4
DETAIL L
1:3
37 .13 3 7.13
37 22 4 F
E 18 D 17 SECTION E-E G
3 0 16 1 29
6 9.06 35 20
20 29
20
20
11 35 20
25 35
4 DETAIL F 4
25
1:3
DETAIL H DETAIL G
1:3 H 1:3
23
38
33
18
DETA IL I K
1:3
21 21
36 3 1
26
J SECTION D-D
DETAIL J
ISO VIEW 1:3
1:8
30
ASSEMBLY NOTE: 19 20 35
M-I L .L . C.
APPLY RED SILICON SEALANT 595 0NORTHCOURSE DRIVE,HOUSTON , TEXAS 77072
(LOCTI TE 59675)ALON G DETAIL K SCALE SH
EE T SIZE DRAW INGNO . R EV
MOUNTINGFACES.
F IL E NAM E: Sw ac o D 2
1:3 1/6 4 OF 6 D 9673015 -
Section 9.13
Document Title: Vent Hood Assemblies
Mongoose PT Platform Mud Cleaner
Section 9.13
774.
37.1
7
7
. 94 .50 .9 4
10 11 10 11 6
5
M -I L .L . C.
F IL E NA M E: Swac oD 2
1/6 5OF 6 D 9673015 -
11
12
N
65.5
62.3
N
O
SECTION N-N
P 14
14
6
10 15
1 15
15
15
37
22
14
12
DETAIL O
1:3 13 38.5
P
3 5.08
13
R
LOCATE ENDS OF
GASKET AS SHOWN
Q
SECTION P-P 14
35
29 15
1
37
22
13 DETAIL R
2 PLCS. 13 1:2
ISO VIEW DETAIL Q
1:10 1:2
M-I L .L . C.
SH
595 0NORTHCOURSE DRIVE,HOUSTON , TEXAS 77072
EE T
DO NOT ASSEMBLE DUCT WORK PRIOR TO INSTALLATION O F VENT HOOD TO D-SILTER HEADER BOX. SCALE SIZE DRAW INGNO . R EV
Section 9.13
Document Title: Vent Hood Assemblies
Mongoose PT Platform Mud Cleaner
Section 10.0
Supplier Logo
Equipment:
Mongoose PT Platform Mud Cleaner
1
THIS PAGE INTENTIONALLY LEFT BLANK
*#.'*#-'4 .'%64+%+$4#614
Table of Contents
Table of Contents
Section Page
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Before Installing Vibrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installing Vibrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Mounting vibrator onto structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Nut and cap screw torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Markings on Vibrators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Thermistors and thermostats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing overload, short-circuit, and ground-fault protection . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
After Installing Vibrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Checking shaft rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjusting eccentric weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Initial start-up/checking line current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Lubricating vibrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Repairing vibrator and replacing bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Inspecting vibrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
List of Tables
Table Title Page
I Mounting Bolts and Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
II Vibrator Nut and Cap Screw Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
III Lubrication Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Introduction
General SWACO Explosion-proof Shale Shaker Electric Vibrators are designed and
manufactured to ensure the best performance and reliability in severe-duty
applications. These vibrators have an ambient temperature rating including
mounting surface temperature of -4 to 131° F (-20 to 55° C). If operating the
vibrator in environments beyond these temperatures, call SWACO, as the
vibrator may require rating reduction, more frequent lubrication, or
lubrication substitution.
References
The following documents are referenced in this manual:
• The National Electrical Code (NEC), National Fire Protection Association,
1 Batterymarch Park, P.O. Box 9101, Quincy MA 02269-9101.
• American National Standards Institute (ANSI) z244.1-1982, American
National Standard for Personnel Protection - Lockout/Tagout of Energy
Sources - Minimum Safety Requirements, American National Standards
Institute, Inc., 1430 Broadway, New York, NY 10018.
• Code of Federal Regulation (CFR) 29, Part 1910, Control of Hazardous
Energy Source (Lockout/Tagout); Final Rule, Department of Labor,
Occupational Safety and Health Administration (OSHA), 32nd Floor,
Room 3244, 230 South Dearborn Street, Chicago, IL 60604.
• CFR 29, Part 1910.15, Occupational Noise Exposure, Department of Labor,
OSHA, 32nd Floor, Room 3244, 230 South Dearborn Street,
Chicago, IL 60604.
Safety All safety rules defined in the above documents and all owner/employer
safety rules must be strictly followed when working on the vibrator.
Storage Store vibrator in an ambient temperature not less than 41°F (5°C) with a
relative humidity not more than 60%. If the vibrator has been stored for 2 or
more years, remove bearings, wash them, and repack them with new grease
(see “Lubricating Vibrator”).
1. Make sure mounting surface is strong and flat, 0.010 in. (0.25 mm) across
vibrator feet. (This will minimize internal stress to vibrator casting when
tightening mount bolts. Welding in the area of the mounting surface could
affect flatness.)
2. Make sure mounting surface and bottom of vibrator feet are clean and free
of debris, paint, and oxidation.
Installation
! CAUTION
Use only new Grade 5 bolts (or metric equivalent) and lock
nuts to install vibrator. Old fasteners can break and cause
damage to vibrator or structure.
Do not use split lock washers to install vibrator onto mount.
Damage to vibrator could result.
Tighten mounting bolts in sequence shown in Figure 1. If not
tightened in order, vibrator casting could be damaged.
1. Before installing vibrator onto mount, apply thread sealing compound to
all bolts.
2. Install vibrator onto mount with new lock nuts, compression washers, and
bolts according to Table I. Tighten bolts in order given in Figure 1 to
avoid damaging vibrator casting. (Contact fastener manufacturer for
specific information regarding bolt torque.)
3 6
1 4
1 2
3 2
5 4
4 Bolts 6 Bolts
*Torque specifications are for reference only. Contact fastener manufacturer for specific information
regarding bolt torque.
Nut and cap screw After removing any nuts or cap screws from vibrator assembly, re-install to
torque the torque values specified in Table II.
Stainless Nameplate
! WARNING
Wire vibrator in accordance with National Electrical Code
(Articles 430, 500, 501, and 502, as appropriate) and all
applicable local codes. Have wiring installed by a qualified
electrician only.
P1 P2
6-lead, 3-phase
P1 P2
W2 U2 V2 W2 U2 V2
W1 W1
U1 V1 U1 V1
G G
Cable Entry
Y - High Voltage s - Low Voltage
! CAUTION
Before running cord to vibrator, make sure cord voltage
rating equals or exceeds the voltage at which you will be
operating the vibrator. It must have a minimum temperature
rating of 222°F (105°C).
1. Remove wiring cover, O-ring, and rubber compression block. Install
elbow or conduit fitting as appropriate. Install cord so that cord jacket
extends into wiring compartment approximately 1 inch. Complete
installation of fittings in accordance with their installation instructions.
IMPORTANT
When wiring vibrator, leave slack in electrical cable so that
cable does not become taut during vibration cycle and cause
Wire
connector
Flat
washers
! WARNING
Vibrator must be grounded using the power supply ground
wire (or other if specified in the NEC). Failure to properly
ground vibrator can cause severe injury or death.
4. Connect power supply ground wire (or other if specified in the NEC) to
ground terminal. Use closed loop wire connector only.
IMPORTANT
A thermistor or thermostat control circuit will be provided. It
is required that these circuits be connected to the motor
control circuit. However, these devices are optional for units
marked with a 55°C ambient rating.
NOTE
The thermistor terminals are identified as T1 and T2.
1. For vibrators having a thermistor circuit, wire thermistor to control
module in accordance with Figure 4. (Other suitable control modules may
be used.)
T1 T2
NOTE
The thermostat terminals are identified as P1 and P2 (Figure
5). The thermostat circuit is rated 600 Vac maximum and 720
VA. A manual momentary start switch must be used.
U Windings
3
P1
Stop
Start
P2
Starter Starter
Coil Overload
Contacts
! CAUTION
Installing Install overload protection for vibrator. If vibrator is not
overload, short- protected from overload, vibrator can be damaged and
circuit, and warranty will be void. Determine size of overload protection
ground-fault according to NEC Article 430, and have it installed by a
protection qualified electrician only.
1. Determine overload, short-circuit, and ground-fault protection according
to NEC Article 430.
2. Have qualified electrician install overload, short-circuit, and ground-fault
protection.
3. If overload trips during operation, fix problem before resetting.
! CAUTION
The vibrator control circuit must be arranged so that if one
vibrator becomes de-energized, the other vibrator will
automatically and immediately become de-energized. Failure
to properly interlock vibrators could result in damage to
equipment if one vibrator fails.
4. Interlock the two vibrators and install separate overload protection for
each.
IMPORTANT
Read entire section before beginning work.
Checking shaft 1. Remove one weight cover.
rotation
! WARNING
Before checking shaft rotation, make sure area is known to be
non-hazardous.
! CAUTION
DO NOT run vibrator with eccentric weights removed.
Running vibrator with eccentric weights removed will
damage bearings.
! WARNING
When checking shaft rotation with weight cover removed,
keep hands away from swinging weights. Weights can crush
fingers.
2. Start vibrator(s) only for a few seconds, then stop.
3. Observe direction of vibrator rotation. If vibrator is not rotating in correct
direction, lock out/tag out energy source and reverse rotation. To reverse
rotation of three-phase vibrator, reverse any two of the three power
supply wires.
4. Replace weight cover, taking care not to pinch o-ring.
After Installation
Adjusting All Vibrators have one set of eccentric weights on each end of
eccentric weights shaft. Eccentric weights are set at 0% at factory. See Figure 6.
The percentage increments on the weight adjustment disks
are percentages of the total force pounds listed on the
nameplate. For example, if the nameplate shows 6000 lb,
setting the weights to 50% would produce 3000 pounds of
force.
IMPORTANT
For the most efficient operation, vibrator eccentric weights
should be adjusted to the lowest force setting required to move
the material. This will increase vibrator life and reduce energy
costs.
! WARNING
Before adjusting eccentric weights, turn off and lock out/tag
out energy source to vibrator.
1. Turn off and lock out/tag out energy source to vibrator according to ANSI
standards (see “References”).
2. Remove weight cover.
3. Loosen screw (A, Figure 6) so adjustable weight (B) will rotate around
shaft (C).
C
A. Screw
B. Adjustable weight
C. Shaft
D. Fixed weight
B
D
Figure 6. Adjusting Eccentric Weights
NOTE
The fixed weight is attached to the shaft. The adjustable
weight rotates around the shaft. The weight adjustment disk
will be attached to either the fixed or the adjustable weight.
4. See Figure 10. Rotate adjustable eccentric weight to proper setting. To
produce more force, move weight to higher setting (i.e., higher number).
When set, tighten cap screw according to Table II.
5. Check o-rings for damage. Replace if damaged.
! CAUTION
Do not operate vibrator with weight covers removed. Dust
accumulating around vibrator shaft could cause unit to fail.
6. Replace weight covers.
! CAUTION
Adjust both sets of eccentric weights to same setting number
(mirror images), or force output will be uneven and damage
vibrator.
7. Repeat steps 2 through 5 for second set of weights. Set both sets of
weights to same setting number so they are mirror images, as shown in
Figure 7.
Initial start-up/ 1. Close power supply disconnect switch and allow vibrator(s) to operate.
checking line 2. If vibrator makes unusual or excessive noise, make sure mounting bolts
current are tight and mount welds are not damaged.
! WARNING
Vibrator may produce loud noise during operation when
mounted on structure. See OSHA 1910.95 for guidelines. If
required, wear ear protection to avoid impairment or loss of
hearing.
3. Check decibel level of vibrator noise during operation. See OSHA
1910.95 to determine whether noise exceeds safe limits. If required, wear
ear protection to avoid impairment or loss of hearing.
Lubricating
vibrator IMPORTANT
Read entire section before beginning work. Allow vibrator to
cool to ambient temperature before working on it.
NOTE
All vibrators are lubricated at the factory.
! CAUTION
Use only prescribed grease in vibrator. If a different grease is
used, vibrator can be damaged and warranty will be void.
Use only prescribed amount of grease to lubricate vibrator.
Too much grease will cause bearings to overheat and result in
premature bearing failure.
1. Lubricate the vibrator with Kluber Isoflex Topas NB 52 grease according
to Table III.
30 N/A Life
50 16 2000
60 25 3000
70 40 2000
! CAUTION
Repairing vibrator Repairing vibrator yourself during the warranty period may
and replacing void the warranty. Contact SWACO if motor needs repair.
bearings
If vibrator needs repair or if bearings need to be replaced, call your local
representative or SWACO for instructions.
Part Numbers
Frame Size 30
CDX Part Numbers:
601149
16
28 22 13
26 23 32
25
27
4
5
22
33 23
25
19 20
30 31 21 17
3
18
34 14
8
15 36
16
12
13
2 9
11 10 7
1 35 4
5
24 4
26 33 5
19
20
23
24
26
28
29 22
21
27 24
3 14
31
17
8 18
32
36 34
15 12
13
16
2 4
11 35
10 5
7
9
1
27
28
15
16
24
23 25 19
20
18 22
20
17
29
34
30 13
3 14
8 5
11
12
9
4
2 32 33 5
1 7
10
MECHANICAL CHARACTERISTICS
ELECTRICAL CHARACTERISTICS
MECHANICAL CHARACTERISTICS
ELECTRICAL CHARACTERISTICS
MECHANICAL CHARACTERISTICS
ELECTRICAL CHARACTERISTICS
MECHANICAL CHARACTERISTICS
ELECTRICAL CHARACTERISTICS