Professional Documents
Culture Documents
51002073
Application
High accuracy in total ambient Fault signal on sensor break or short EMC to NAMUR NE 21, CE UL recognized component to
UL 3111-1 approval circuit, presettable to NAMUR NE 43 temperature range
Input:
Resistance thermometer (RTD) Thermocouple (TC) Resistance transmitter () Voltage transmitter (mV) HART -protocol for front end unit or panel unit operation using the hand operating module (DXR 275) or PC (e. g. ReadWin2000, COMMUWIN II or FieldCare) Your benefits
TMT 182
Input
Measured variable Measuring range Temperature (temperature linear transmission behaviour), resistance and voltage The transmitter records different measuring ranges depending on the sensor connection and input signals.
min. meas. range 10 K 10 K 10 K 10 K 10 K 10 K
Type of input
Type Pt100 Pt500 Pt1000 acc. to IEC 751 Resistance thermometer (RTD) Ni100 Ni500 Ni1000 acc. to DIN 43760 Measurement ranges -200 to 850 C (-328 to1562 F) -200 to 250 C (-328 to 482 F) -200 to 250 C (-238 to 482 F) -60 to 250 C (-76 to 482 F) -60 to 150 C (-76 to 302 F) -60 to 150 C (-76 to 302 F)
Resistance transmitter
Connection type: 2-, 3- or 4-wire connection Software compensation of cable resistance possible in the 2 wire system (0 to 30 ) Sensor cable resistance max. 20 per cable in the 3 and 4 wire system Sensor current: 0.2 mA 10 to 400 10 to 2000 0 to +1820 C (32 to 3308 F) 0 to +2320 C (32 to 4208 F) 0 to +2495 C (32 to 4523 F) -270 to +1000 C (-454 to 1832 F) -210 to +1200 C (-346 to 2192 F) -270 to +1372 C (-454 to 2501 F) -200 to +900 C (-328 to 1652 F) -270 to +1300 C (-454 to 2372 F) -50 to +1768 C (-58 to 3214 F) -50 to +1768 C (-58 to 3214 F) -270 to +400 C (-454 to 752 F) -200 to +600 C (-328 to 1112 F) 10 100 500 K 500 K 500 K 50 K 50 K 50 K 50 K 50 K 500 K 500 K 50 K 50 K
Resistance B (PtRh30-PtRh6) C (W5Re-W26Re)1 D (W3Re-W25Re)1 E (NiCr-CuNi) J (Fe-CuNi) K (NiCr-Ni) L (Fe-CuNi)2 N (NiCrSi-NiSi) R (PtRh13-Pt) S (PtRh10-Pt) T (Cu-CuNi) U (Cu-CuNi)2 acc. to IEC 584 Part 1
Thermocouple (TC)
Voltage transmitters (mV) 1) 2)
Endress+Hauser
TMT 182
Output
Output signal Signal on alarm Analogue 4 to 20 mA, 20 to 4 mA
Underranging Overranging:
Linear drop to 3.8 mA Linear rise to 20.5 mA
Load Linearisation/transmission behaviour Filter Galvanic isolation Input current required Current limit Switch on delay
max. (VPower supply - 11.5 V) / 0.022 A (Current output) Temperature linear, resistance linear, voltage linear
1st order digital filter: 0 to 100 s U = 2 kV AC (input/output) 3.5 mA 23 mA 4 s (during power up Ia = 3.8 mA)
Power supply
Electrical connection
Endress+Hauser
TMT 182
Performance characteristics
Response time Reference operating conditions Maximum measured error
Resistance thermometer RTD
Measurement accuracy1 0.2 K or 0.08% 0.5 K or 0.20% 0.3 K or 0.12% typ. 0.5 K or 0.08% typ. 1.0 K or 0.08% typ. 2.0 K or 0.08%
Thermocouple TC
Measurement range Resistance transmitter 10 to 400 () 10 to 2000 Voltage transmitters (mV) 1) -10 to 75 mV
% is related to the adjusted measurement range. The value to be applied is the greater.
Td= (15 ppm/K * max. meas. range + 50 ppm/K * preset meas. range) * Td= (15 ppm/K * (range end value + 200) + 50 ppm/K * preset meas. range) * Td= (50 ppm/K * max. meas. range + 50 ppm/K * preset meas. range) *
= Deviation of the ambient temperature according to the reference condition (+23 C (73.4 F) 5 K). Influence of load
0.02%/100
Values refer to the full scale value
Long-term stability
Pt100 DIN IEC 751 Cl. B (internal cold junction with thermocouples TC)
Installation conditions
Installation instructions
Endress+Hauser
TMT 182
Environment conditions
Ambient temperature limits Storage temperature Climate class Condensation Degree of protection -40 to +85 C (-40 to 185 F) for Ex-area, see Ex-certificate
-40 to +100 C (-40 to 212 F) as per EN 60 654-1, class C allowable IP 00, IP 66 installed 4g / 2 to 150 Hz as per IEC 60 068-2-6
Shock resistance and interference emission as per EN 61 326-1 (IEC 1326) and NAMUR NE 21
Mechanical construction
Design, dimensions
Weight Material
approx. 40 g
Housing: Potting:
PUR Cable up to max. 1.75 mm2 (secure screws) PC
Terminals
Human interface
Display elements No display elements are present directly on the temperature transmitter. The measured value display can be called up using the ReadWin 2000, COMMUWIN II or FieldCare PC software. No operating elements are present directly on the display. The temperature transmitter is configured via remote operation with the ReadWin 2000 PC software.
Operating elements
Endress+Hauser
TMT 182
Remote operation
Configuration Hand operating module DXR 275 or PC with Commubox FXA 191 and operating software (ReadWin 2000, COMMUWIN II or FieldCare). Interface PC interface RS232 and Commubox FXA 191. Configurable parameters Sensor type and connection type, engineering units (C/F), measurement range, internal/external cold junction, compensation of wire resistance with 2-wire connection, failure mode, output signal (4 to 20/20 to 4 mA), digital filter (damping), offset, TAG + descriptor (8 + 16 characters), output simulation, customer specific linearization, min./max. process value indicator function
Ex approval
EN 60529: EN 61010:
Degrees of protection by housing (IP-Code) Safety requirements for electrical measurement, control and laboratory instrumentation. Electromagnetic compatibility (EMC requirements) Standardization association for measurement and control in chemical and pharmaceutical industries.
Endress+Hauser
TMT 182
Ordering information
Questionnaire Endress+Hauser iTEMP temperature transmitter Customer specific setup / Kundenspezifische Einstellung
Standard setup / Standardeinstellung Sensor TC ( )B ( )K ( )T ( )C ( )L ( )U ( )D ( )N ( )E ( )R ( )J ( )S ( ) Pt1000 ( ) Ni1000 ( ) 4 wire
RTD
( ) F ,
[0...126]
[0...80C; 32...176F]
Compensation wire resistance / Kompensation Leitungswiderstand Failure mode / Fehlerverhalten Output / Ausgang Damping / Dmpfung Offset TAG PCP HART PROFIBUS-PA , ( ) < 3,6 mA ( ) 4...20 mA ( ) > 21,0 mA ( ) 20...4 mA
[0...20 Ohm] (only / nur RTD 2 wire) [0...30 Ohm] (only / nur HART, PA RTD 2 wire)
(not / nicht PROFIBUS-PA) (not / nicht PROFIBUS-PA)
[0, 1, 2,..., 8s] (only / nur PCP) [0, 1, 2,..., 100s] [-9,9...0...+9,9K]
Endress+Hauser
TMT 182
Product structure
Head transmitter iTEMP HART TMT 182 Temperature transmitter with HART-Protocol for RTDs, TCs, Ohm and mV, analogue output 4 to 20 mA, 2-wire-technology, Galvanic isolation, fail. mode to NAMUR NE 43, for mounting in Form B head to DIN 43729, UL recognized component, ship building approval GL (Germanischer Lloyd)
Certification
A B C D E F G H Version for non hazardous areas ATEX II1G EEx ia IIC T4/T5/T6 FM IS, Class I, Div. 1+2, Group A, B, C, D CSA IS, Class I, Div. 1+2, Group A, B, C, D ATEX II3G EEx nA IIC T4/T5/T6 ATEX II3D ATEX II1G EEx ia IIC T6, II3D ATEX II3G EEx nA IIC T6, II3D
Configuration
A B C D Standard factory configuration (Pt100/3-wire/0 to 100 C) Customised measurement range Customised expanded configuration for TC (see questionnaire) Customised expanded configuration for RTD (see questionnaire)
Model
A B TMT182Standard model Works calibration certificate 6 test points Order code (complete)
Customised options
51003527 51003546 TAG print/configuration 8 char Descriptor print/configuration 16 char
Accessories
Commubox FXA 191 Order code: FXA191-G1 PC-operating software: ReadWin 2000, COMMUWIN II or FieldCare
Endress+Hauser
TMT 182
ReadWin2000 can be downloaded free of charge from the internet from the following address: www.endress.com/readwin Hand operating module HART Communicator DXR 275, Order code: DXR275-...
Documentation
System information Temperature measurement (SI 008R/09/en) Operating short manual iTEMP HART TMT 182 (KA 142R/09/a3) Additional documentation for use in explosion-hazardous areas: ATEX II1G: XA 006R/09/a3 ATEX II3G: XA 011R/09/a3 ATEX II3D: XA 027R/09/a3 FM, CSA, etc. Operating manual iTEMP HART Communication (BA 139R/09/a3) Operating short manual TAF 10 Field housing (KA 093R/09/a2)
Endress+Hauser
TMT 182
Endress+Hauser GmbH+Co. Instruments International P.O. Box 2222 D-79574 Weil am Rhein Germany Tel. (07621) 975-02 Tx 773926 Fax (07621) 975 345 e-mail: info@ii.endress.com
Internet: http://www.endress.com
11.01