Professional Documents
Culture Documents
Optimization algorithm is used to adapt PS DCH channel bit rate using radio bearer reconfigurations so that the bit rate meets the actual capacity requirement
Channel can be even released if the utilization of the channel is low enough Optimization is based on throughput measurement of the channel Optimization is performed in both uplink and downlink. Throughput-based optimisation works in parallel with the inactivity timer. The NRT DCH has to be totally silent during the inactivity period until it is released.
ave_throughput
downgrade_threshold 1 downgrade_threshold 2 release_threshold send downgrade request to PS send release request to PS
Adapts the allocated DCH to the data bit rate Better utilization of radio, transport and HW resources Triggers transition to FACH when throughput is sufficiently low without check of inactivity
timers Applied also to HSDPA return channel (controlled with parameter)
2 Nokia Siemens Networks
Yellow dots with the number are related to RB reconfiguration events, and explained below 1. Initial bit rate is allocated (64kbps) 2. UG to Maximum bit rate (384kbps) 3. Uplink is DG from 64 kbps (initial) to 8 kbps (7s) - DG is happening due the lower throughput measurement but DCHutilguardtime (6s) is delaying DG 4. DG DL 384 kbps to 256 kbps. This DG is based on upper throughput measurements. Upper downgrade threshold for 384 kbps is 256 kbps which happens around 7sec. after maximum was allocated. 5. DG DL 256 kbps to 128 kbps. This downgrade is also based on upper throughput measurements. Upper downgrade threshold for 256 kbps is 128 kbps. This happens around 7sec. after previous downgrade from 384 kbps to 256 kbps. 6. Release to CELL_FACH, this event is based on release throughput measurements
3 Nokia Siemens Networks
NRT DCH
RLC buffer
time Throughput / DCH bit rate
High Throughput Measurement Unnecessary upgrades can be avoided with the high throughput measurement:
Upgrade can be allowed only if the current DCH utilization is above threshold
Flexible upgrade provides a mechanism to control the bit rate upgrades in order to avoid unnecessary ones. Throughput is checked along with capacity upgrade requests. Applied also to HSDPA return channel (controlled with parameter)
4 Nokia Siemens Networks
DCHUtilLowerAveWin (128, 256, 32, 384, 64): This parameter defines the lower sliding
measurement window size for the NRT DCH. The lower throughput measurement measures the number of received/sent bits in UL/DL NRT DCH during the sliding measurement window period. The special value 0 of this parameter means that the lower throughput measurement is not actived for the NRT DCH.
DCHUtilUpperAveWin (128, 256, 32, 384, 64): This parameter defines the upper sliding
measurement window size for the NRT DCH. The upper throughput measurement measures the number of received/sent bits in UL/DL NRT DCH during the sliding measurement window period. The special value 0 of this parameter means that lower throughput measurement is not actived for the NRT DCH.
DCHUtilUpperTimeToTrigger (128, 256, 32, 384, 64): This parameter defines the period of
the time between timing of the upper throughput goes below the upper bit rate threshold and the timing of sending upper downgrade request for the NRT DCH.
Flexible Upgrade
DCHUtilHighAveWin: This parameter defines the sliding measurement window size for the
high throughput measurement in uplink and downlink NRT dedicated channels. The high throughput mesurement measures the number of received/sent bits in UL/DL NRT DCH during the sliding measurement window period. The measurement window size is common for all NRT DCH data rates. The special value 0 means that high throughput measurement is not active. Time to Trigger for the high throughput measurement is respectively 0.2 s, which means that the measured bit rate over 1.2 s needs to be greater than the high throughput threshold before the NRT DCH data rate can be upgraded. Zero (0) means high throughput measurement is inactive
New Value
Comments
RNC
DCHUtilBelowDowngradeThr
On-line
4%
RNC
DCHUtilHighAveWin
On-Line
500 ms
RNC RNC RNC RNC RNC RNC RNC RNC RNC RNC RNC
Threshold below the NRT DCH data rate DCHUtilHighBelowNRTDataRateThr Lower measurement window size for NRT DCH of 128 kbps DCHUtilLowerAveWin128 Lower measurement window size for NRT DCH of 256 kbps DCHUtilLowerAveWin256 Lower measurement window size for NRT DCH of 32 kbps DCHUtilLowerAveWin32 Lower measurement window size for NRT DCH of 384 kbps DCHUtilLowerAveWin384 Lower measurement window size for NRT DCH of 64 kbps DCHUtilLowerAveWin64 Lower time to trigger for the NRT DCH of 128 kbps DCHUtilLowerTimeToTrigger128 Lower time to trigger for the NRT DCH of 256 kbps DCHUtilLowerTimeToTrigger256 Lower time to trigger for the NRT DCH of 32 kbps DCHUtilLowerTimeToTrigger32 Lower time to trigger for the NRT DCH of 384 kbps DCHUtilLowerTimeToTrigger384 Lower time to trigger for the NRT DCH of 64 kbps DCHUtilLowerTimeToTrigger64 Guard time for throughput measurement Upper measurement window size for NRT DCH of 128 kbps Upper measurement window size for NRT DCH of 256 kbps Upper measurement window size for NRT DCH of 32 kbps Upper measurement window size for NRT DCH of 384 kbps Upper measurement window size for NRT DCH of 64 kbps Upper time to trigger for the NRT DCH of 128 kbps Upper time to trigger for the NRT DCH of 256 kbps Upper time to trigger for the NRT DCH of 32 kbps Upper time to trigger for the NRT DCH of 384 kbps Upper time to trigger for the NRT DCH of 64 kbps
On-line On-Line On-Line On-Line On-Line On-Line On-Line On-Line On-Line On-Line On-Line
4% 1000 ms 1000 ms 1000 ms 1000 ms 1000 ms 800ms 800ms 800ms 800ms 800ms
This recommendation aims to speed up bit rate downgrade once utilization is below defined threshold. Combined with others TBO parameters brings a better DCH utilization (higher throughput per Radio Bearer) and therefore reduces CE consumption. Related to High Throughput Measurements. It means that the measured bit rate over DCHUtilHighTimeToTrigger + DCHUtilHighAveWin needs to be greater than the high throughput threshold before the NRT DCH data rate can be upgraded. Related to High Throughput Measurements. This recommendation aims to retard bit rate upgrade once utilization is below defined threshold.
200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms) 140 (1400 ms)
It's related to Throughput Based Optimization (TBO) feature. This recommendation aims to speed up bit rate downgrade once utilization is below defined threshold. Combined with others TBO parameters brings a better DCH utilization (higher throughput per Radio Bearer) and therefore reduces CE consumption.
RNC RNC RNC RNC RNC RNC RNC RNC RNC RNC RNC
DCHUtilMeasGuardTime DCHUtilUpperAveWin128 DCHUtilUpperAveWin256 DCHUtilUpperAveWin32 DCHUtilUpperAveWin384 DCHUtilUpperAveWin64 DCHUtilUpperTimeToTrigger128 DCHUtilUpperTimeToTrigger256 DCHUtilUpperTimeToTrigger32 DCHUtilUpperTimeToTrigger384 DCHUtilUpperTimeToTrigger64
On-Line On-Line On-Line On-Line On-Line On-Line On-Line On-Line On-Line On-Line On-Line
2s 1000ms 1000ms 1000ms 1000ms 1000ms 2000ms 2000ms 2000ms 2000ms 2000ms
If TimeToTrigger and AveWin are reduced as recommended above, then DCHUtilMeasGuardTime should be reduced to avoid being a bottleneck.
200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 200 (2000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms) 400 (4000 ms)
It's related to Throughput Based Optimization (TBO) feature. This recommendation aims to speed up bit rate downgrade once utilization is below defined threshold. Combined with others TBO parameters brings a better DCH utilization (higher throughput per Radio Bearer) and therefore reduces CE consumption.