Professional Documents
Culture Documents
3g Radio Parameter Ericsson
3g Radio Parameter Ericsson
Radio Parameter
TELKOMSEL
Contents
Idle Mode
Handover
Power Control
Capacity Management
Channel Switching
HSDPA
qQualMin : indicates the minimum required quality value in the cell. It is sent in
system information, in SIB3 for the serving cell, and in SIB11 for adjacent cells
qRxLevMin : indicates the minimum required signal strength in the cell. It is sent
in SIB3 for the serving cell and in SIB11 for adjacent cells
maxTxPowerUl : indicates the maximum allowed transmission power when the
UE accesses the system on RACH. It is broadcast in SIB3
Squal > 0
qQualMin
(18)
Squal = Qqualmeas qQualMin
qRxLevMin
(115)
suitabl
e
cell?
Qrxlevmeas (dBm)
CPICH RSCP
Pcompensation
Pcompensation = max(maxTxPowerUl P, 0) (dB)
Srxlev = Qrxlevmeas - qRxLevMin Pcompensation
Srxlev > 0
qOffset(s,n)
qOffset2sn : Based on CPICH Ec/No
(1 ) qHyst(s) and qOffset(sn) based on CPICH RSCP only
qualMeasQuantity =x
The decision about when GSM measurements are performed is made using the sRatSearch
parameter in relation to Squal and the sHcsRat parameter in relation to Srxlev:
If the Squal > sRatSearch and the Srxlev > sHcsRat, the UE does not need to perform measurements on
GSM cells.
If the Squal <= sRatSearch value and/or the Srxlev <= sHcsRat value, the UE performs measurements on
GSM cells.
calculation, with
hysteresis parameter
Rn = Neighbour WCDMA or GSM
cell calculation with offset
parameter
Yes
No
Qhyst2 = 4 dB
qOffset2sn = 0 dB
Cell re-selection
to GSM
If a TDD or GSM cell is ranked as the best cell, then the UE
must perform cell re-selection to that TDD or GSM cell.
Cell re-selection to
WCDMA cell of highest
R value
RSCP
qHyst1 = 4 dB
First ranking of all the cells based on
CPICH RSCP (WCDMA) and RSSI (GSM) qOffset1sn = 0 dB
qQualMin = -18 dB
Rs
=
CPICH
RSCP/GSM
RSSI
+
Qhyst1
CPICH Ec/No qQualMin < SRatSearch
sRATsearch = 4 dB
Rn= CPICH_RSCP(n) or RXLEV(n) - Qoffset1
qOffset1sn = 7 dB
Rs = Serving WCDMA cell
GSM cell measurements
available If :
RSSI
Value
10
14
15
dBm
-98
-94
-74
Always
-78
-74
-70
-54
Never
UE always
measures 3G cells
UE never
measures 3G cells
dBm
-20
-19
-18
-17
-16
-15
-14
-13
FDDQOFF
Value
14
15
dBm
-32
(infinity)
-28
-24
-20
24
28
Always select
irrespective of RSCP
value
QSI = 7(always)
Check levels every 5s
from serving GSM cell
and best 6 GSM
neighbour cells
DEFAULT:
DEFAULT:
fdd
cell
reselect
fdd cell reselectoffset
offse
select
always
select always
(value
(valueis
is-infinity)
-infinity)
UE
UEstarts
startsWCDMA
WCDMAmeasurements
measurementsififRxlev
Rxlev
running
average
(RLA_C)
is
below
or
above
running average (RLA_C) is below or above
certain
certainthreshold:
threshold:
RLA_C
QSI
RLA_C QSIor
orQSC
QSC
minimum
minimumfdd
fdd
threshold
=
-12
threshold = -12dB
dB
Compare levels
of all GSM cells
to WCDMA
neighbour
Check quality
of neighbour
WCDMA cells, no
priorities between
WCDMA
neighbours
UE
UEcan
canselect
selectWCDMA
WCDMAcell
cellifif the
thelevel
levelofofthe
the
serving
GSM
and
non-serving
GSM
cells
has
serving GSM and non-serving GSM cells hasbeen
been
exceeded
by
certain
offset
for
a
period
of
5
s:
exceeded by certain offset for a period of 5 s:
CPICH
CPICHRSCP
RSCP>> RLA_C
RLA_C++FDDQOFF
FDDQOFF
RSCP
>
(aveRxLev)
+
RSCP > (aveRxLev) +-32
-32
FDDQMIN = -13 dB
UE
UEwill
willre-select
re-selectWCDMA
WCDMAcell
cellinincase
caseit's
it's
quality
is
acceptable:
quality is acceptable:
CPICH
CPICHEc/No
Ec/NoFDDQMIN
FDDQMIN
EcNo
-13
EcNo -13
FDDQOFF = -32 dB
WCDMA
cell
reselecti
on
accessClassNBarred
bandIndicator
bcchFrequency
cellReserved
fachMeasOccaCycLenCoeff
BCCH frequency code in the GSM cell. Contains the absolute radio
frequency channel number of the BCCH channel for the GSM cell. It
uniquely identifies the BCCH.
Indicates if this cell shall be reserved for operator use. If it is reserved,
there will be no service to the UEs.
Fach Measurement Occasion Cycle Length coefficient. A factor used
when the UE performs inter-frequency and inter-system
measurements. The UE uses this parameter to calculate the interval
length in order to determine the repeating cycle of the measurement.
0 : not broadcasted in SIB 11.
1 : not used.
2 : not used.
3 : used when inter frequency and GSM neighbours.
4 : used when inter freqency or GSM neighbours.
5 - 12 not used.
interFreqFddMeasIndicator
mnc
The MNC part of the PLMN identity used in the radio network.
The PLMN identity consists of two parts:
1. MobileCountryCode, MCC, 3 digits
2. MobileNetworkCode, MNC, 2 or 3 digits
Example: If MCC=125 and MNC=46 then plmnId=12546.
nmo
primaryScramblingCode
qHyst2
The hysteresis value of the serving cell. Used to perform cell ranking
for the serving cell.
Resolution: 2
qOffset1sn
Signal stength offset between source and target cells. Used when the
IE "cell_selection_and_reselection_quality_measure" in SIB 11/12 is
set to "CPICH RSCP". This is configured through
UtranCell::qualMeasQuantity.
Unit: 1 dB
Resolution: 1
-50 : -50dB
-49 : -49dB
-48 : -48dB
......
50 : 50dB
sHcsRat
sIntraSearch
sRatSearch
uarfcnDl
uarfcnUl
att
lAC
rAC
t3212
cnDrxCycleLengthCs
Core Network DRX cycle length coefficient (k) for UEs in idle mode,
circuit switched.
The cycle length is calculated as the k'th potential of 2, where k = 6..9.
For example, 6 corresponds to cycle length 640 ms, 7 corresponds to
cycle length 1280 ms, etc.
cnDrxCycleLengthPs
Core Network DRX cycle length coefficient (k) for UEs in idle mode,
packet switched.
The cycle length is calculated as the k'th potential of 2, where k = 6..9.
For example, 6 corresponds to cycle length 640 ms, 7 corresponds to
cycle length 1280 ms, etc.
noOfMaxDrxCycles
noOfPagingRecordTransm
System Information
noOfMibValueTagRetrans
sib1PlmnScopeValueTag
sib1RepPeriod
sib3RepPeriod
sib5RepPeriod
sib7RepPeriod
sib11RepPeriod
sib12RepPeriod
sib1StartPos
sib3StartPos
sib5StartPos
sib7StartPos
sib11StartPos
sib12StartPos
sib7ExpirationTimeFactor
updateCellReattsNo
UE States
Idle mode
No connection to radio network (No RRC connection established)
This minimizes resource utilization in UE and the network
CELL_FACH mode
User Equipment (UE) in Connected Mode (has an RRC Connection to
radio network)
UE uses the common transport channels RACH or FACH
If the parameter interFreqFDDMeasIndicator = 1, the UE will evaluate cell
reselection criteria on inter-frequency cells (0)
CELL_DCH mode
User Equipment (UE) in Connected Mode (has an RRC Connection to
radio network)
UE uses dedicated channels for transmitting data and signalling
Power Control
P-CPICH
dl/ulAttenuation
dl/ElectDelay
TopOfRack
MaxTxPowerDL
With increasing CPICH power capacity directly decreasis, but common channels and
power per each dedicated channel is calculated from CPICH
At CPICH 30 dBm, the common channel will be configured as follow:
primaryCpichPower
bchPower
primarySchPower
secondarySchPower
constantValueCprach
L_PCPICH
RTWP
constantValueCprach
As soon as the RBS properly detects the preamble, it sends an Acknowledgement Indicator
(AI) on the AICH.
While not receiving any AI, the UE transmits a new preamble, increasing the transmission
power with respect to the previous one by the configurable parameter powerOffsetP0.(3dB)
As soon as the UE receives an AI, it sends the PRACH message part. The power of the
control part of the random access message is determined by the power of the last
transmitted preamble and by a configurable offset powerOffsetPpm.(- 4dB) The power of
the data part of the PRACH message is determined by the gain factors for PRACH, which is
included in System Information.
In average coverage conditions the RRC Connection Setup performance can be improved by tuning
the open loop power control parameters
These parameters are
preambleRetransMax and & maxPreambleCycle
powerOffsetPpm
powerOffsetP0
L1 ACK / AICH
DownlinkNot detected
BS
MaxTXPowerUl
powerOffsetP0
Initial
preamble
power
Uplink
Preamble
MS Preamble
1
Preamble
preambleRetransMax
maxPreambleCycle
powerOffsetPpm
Message part
Handover
Soft/Softer Handover
Inter-Frequency Handover
Inter-RAT Handover
Inter-RAT Cell Change
HSDPA Mobility
Intra-Frequency Handover
SOFTER HANDOVER
Both UL and DL: Maximum Ratio Combining (MRC) is occurring in rake receiver
SOFT HANDOVER
DL/UE: MRC
Arises when inter-RNC SHO is not possible (Iur not supported or Iur congestion)
Inter-Frequency Handover
Can be intra-BS, intra-RNC, inter-RNC
Network Evaluated HandOver (NEHO)
Inter-RAT (Inter-system) Handover
Handovers between GSM and WCDMA (NEHO)
Active Set
The cells involved in soft handover and measured by the UE
Virtual Active Set
The Active Set associated with a non-used frequency for support of Inter-Frequency
evaluation
Monitored Set
The cells only measured by the UE and not part of the Active Set. The monitored set can
consist of intra-frequency, Inter-Frequency and Inter-RAT cells
Detected Set
The intra frequency cells(P-CPICH scrambling codes) detected by the UE but not part of
Active Set or monitored set
Soft/Softer Handover
Event 1a, A primary CPICH enters the Reporting Range
(measured P-CPICH Ec/No) > (P-CPICH Ec/No of the Best Cell in the Active Set) reportingRange1a + hysteresis1a /2
When a P-CPICH, not included in the Active Set, enters reportingRange1a + hysteresis1a/2, and the
measured value remains in reportingRange1a + hysteresis1a/2 at least a time equal to timeToTrigger1a
(Time to Trigger 1a), event 1a occurs. The UE sends a MEASUREMENT REPORT message for event 1a to
the SRNC. If the report contains more than one cell fulfilling 1a criteria, only the one with highest Ec/No is
considered and retained. If the retained cell is a valid cell and Active Set is not full (present cells in the
Active Set is less than maxActiveSet parameter), the cell is proposed to be added to the Active Set. If
the Active Set is full, the cell is proposed as a replacement of the worst cell in the Active Set provided that
the reported cell has a better quality than the worst cell in the Active Set.
Soft/Softer Handover
Event 1a and Event 1b
10dB
6dB
320 ms
640 ms
Soft/Softer Handover
Event 1c, A non-active primary CPICH becomes better than an Active Primary
CPICH
(measured P-CPICH Ec/No) > (P-CPICH Ec/No of the Best Cell in the Active Set) +
hysteresis1a /2
When a P-CPICH, not included in the
Active Set, becomes stronger than the
weakest
P-CPICH+hysteresis1c /2 in the Active
Set during a time at least equal to
timeToTrigger1c,and the Active Set is full
(present cells in the Active Set is equal
to maxActiveSet parameter) event 1c
occurs. The UE sends a
MEASUREMENT REPORT message for
event 1c to the SRNC. If the retained cell
is a valid cell, and the Active Set is full,
the cell is proposed as a replacement for
the weakest cell in the Active Set
Hysteresis1c (2dB)
320 ms
Soft/Softer Handover
Parameter Summary
Setting Value
Remark
reportingRange1a
3 dB
reportingRange1b
10
5 dB
timeToTrigger1a
11
320ms
timeToTrigger1b
12
640ms
timeToTrigger1c
11
320ms
timeToTrigger1d
14
2560ms
hysteresis1a
hysteresis1b
hysteresis1c
1dB
hysteresis1d
15
7dB
maxActiveSet
Inter-RAT Handover
Event 2d, The Estimated Quality of the Currently Used frequency is below a
Certain Threshold
When the estimated quality of the current WCDMA RAN used frequency is below the absolute threshold
usedFreqThresh2dEcno - hysteresis2d/2, during a time at least equal to timeToTrigger2dEcno, OR the
estimated quality of the current WCDMA RAN used frequency is below the absolute threshold
usedFreqThresh2dRscp - hysteresis2d/2, during a time at least equal to timeToTrigger2dRscp, event 2d
occurs.
Event 2f, The estimated quality of the currently used frequency is above a
certain threshold
When the estimated quality of the current WCDMA RAN used frequency is above the relative threshold
usedFreqRelThresh2fEcno+usedFreqThresh2dEcno + hysteresis2f/2, during a time at least equal to
timeToTrigger2fEcno, AND the estimated quality of the current WCDMA RAN used frequency is above the
relative threshold usedFreqRelThresh2fRscp+usedFreqThresh2dRscp + hysteresis2f/2, during a time at
least equal to timeToTrigger2fRscp event 2f occurs. The UE sends a MEASUREMENT REPORT message
for event 2f to the SRNC. When SRNC receives the MEASUREMENT REPORT message for event 2f from
the UE, measurements for IRATHO_eval event 3a or IFHO_eval event 2b and associated compressed mode
usage is stopped.
Inter-RAT Handover
Compressed Mode and de-Compressed Mode
UE stop compressed
mode
1 + (-12 dB)
-12 dB
640 ms
UE start compressed
mode to measure GSM
or Interfreq Neighbors
2560 ms
Inter-RAT Handover
Event 3a, The Estimated Quality of the Currently Used UTRAN Frequency is
below a Certain Threshold and the Estimated Quality of the Other System is
above a Certain Threshold
The event 3a occurs according to the following points:
When the estimated quality of the WCDMA RAN used frequency is below the threshold
usedFreqThresh2dEcno+utranRelThresh3aEcno - hysteresis3a/2 and the measured GSM carrier RSSI
of a GSM/GPRS cell is above the absolute threshold gsmThresh3a, during a time at least equal to
TimeToTrigger3a
when the estimated quality of the WCDMA RAN used frequency is below the threshold
usedFreqThresh2dRscp+utranRelThresh3aRscp - hysteresis3a/2 and the measured GSM carrier RSSI
of a GSM/GPRS cell is above the absolute threshold gsmThresh3a, during a time at least equal to
TimeToTrigger3a
in case of the connection quality has been triggered in UL for UE TX power (event 6a, see Event 6a, The
UE Tx Power becomes larger than an Absolute Threshold), the event 3a is triggered when the estimated
quality of the WCDMA RAN used frequency is below the threshold
usedFreqThresh2dRscp+utranRelThresh3aRscp+utranRelThreshRscp - hysteresis3a/2 and the
measured GSM carrier RSSI of a GSM/GPRS cell is above the absolute threshold gsmThresh3a , during a
time at least equal to TimeToTrigger3a.
Inter-RAT Handover
RSSI -95dB
320 ms
External
Networks
GGSN
Gn
Gn
3G-SGSN
2G-SGSN
Gb
Iu
SRNC
BSC
Abis
Iub
RBS
RBS
RBS
RBS
RBS
RBS
CN/SGSN
CELL_DCH
1. DCCH (AM) Measurement Report (Event 2d)
2. Evaluation of MR
3. Compressed Mode Control
4. DCCH (AM) Measurement Control
5. DCCH (AM) Measurement Report (Event 3a)
6. Evaluation of MR
7. DCCH (AM):CELL_DCH Cell Change Order from UTRAN
8. GSM: RA Update
9. SRNS Context Request
10. Stop DL Transmission
11. SRNS Context Response
12. Iu Release Command
13. Dedicated Radio Link Release
14. Iu Release Complete
Target BSS
WCDMA RAN neighbor cells are measured only when the signal strength of the
GSM serving cell is above the threshold set by QSI and QSC.
WCDMA RAN neighbor cells are measured only when the signal strength of the
GSM serving cell is below the threshold set by QSI and QSC.
Load sharing
Load sharing
Load
Directed
f1
f1
f1
f1
RNC
RNC
Includes Frequency
Info IE
2nd will not be
redirected but may
be successful or
rejected due to
congestion
Admission
Control
WCDMA
One GSM target can be defined for each WCDMA cell via the cell
parameter directedRetryTarget
loadSharingGsmThreshold specifies the minimum load at which offloading to GSM begins: ex 80% of pwrAdm
RBS/RNC
CN
Relocation Command
Iu release Command
Iu release Complete
Features
Introduction
& Roadmap
WCDMA coverage
Dual Mode UE
GSM terminal
GSM coverage
Load based handover to GSM
during call set up, Directed
Retry (P3) to GSM
Channel Switching
Channel Switching
Channel Switching
Channel Switching
Channel Switching
Future
releases
stand-alone interactive RAB
speech + interactive
RAB
HS
speech
+ 384/HS
384/HS
DCH
64/384
speech
+ 64/HS
128/128
64/HS
speech
+ 64/64
64/128
speech
+ 0/0
64/64
Low/No throughput
Measurement for down
Switch timer period
FACH
IDLE
PS RAB Establishment
UL throughputbased upswitch
activity/inactivity-based
switching UL and/or DL
coverage-triggered
downswitch (DL only)
DL throughputbased upswitch
Capacity Management
* Current
default values
Yes,
then
block
admissionblocked
blocked
IsIsadmission
byCongestion
CongestionControl?
Control?
by
No, then
accept
Checkififthe
therequested
requested++
Check
estimated
#
compressed
modeRL
RL
estimated # compressed mode
>>
compModeAdm
compModeAdm
15*
Checkififthe
therequested
requested
Check
DL
Pwr
+
estimated
Pwr
DL Pwr + estimated Pwr
>>
pwrAdm
pwrAdm
75*
No
Yes,
then
block
No
Checkififthe
therequested
requested
Check
codeusage
usage++estimated
estimatedcode
codeusage
usage
code
>
>
dLCodeAdm
dLCodeAdm
70*
Checkififthe
therequested
requested
Check
ASEUL
UL++estimated
estimatedASE
ASEUL
UL
ASE
>
>
aseUlAdm
aseUlAdm
Only checked if
No
BE-service requests
Checkififthe
therequested
requested
Checkififthe
therequested
requested
Check
Check
DL
SF
+
estimated
DL
SF
ASE
DL
+
estimated
DLASE
ASE
DL SF + estimated DL SF
ASE DL + estimated DL
>>
>>
No
sfXAdm
*
aseDlAdm
sfXAdm *
aseDlAdm
No
Yes,
then
SF8adm= 8* block
SF16adm= 16*
SF32adm= 32*
Yes,
then
block
X = 8 or X = 32
X = 16
240*
160*
Yes,
then
block
Yes,
then
block
AdmissionControl
Controlblocks
blocksthe
thenew
new request
request
Admission
Anexisting
existingng
nguser
userof
of64/384
64/384will
willbe
beswitched
switched down
down to
to 64/128
64/128
An
oran
anexisting
existingng
nguser
userof
of 64/128
64/128will
willbe
beswitched
switcheddown
downto
to64/64
64/64
or
8*
16*
32*
Iu
SRNC &
DRNC
SRNC
Iur
over Iu:
over Iur:
1.
Non-guaranteed service
class connections
2.
Non-guaranteed service
class connections
3.
CS/streaming service
class connections
4.
CS /streaming service
class connections
5.
Speech users
6.
Speech users
HSDPA
Default Value
HSPATHLOSSTHRESHOL
D
Initial Setting
TELKOMSEL
170
170
10
10
HSSCCHMAXCODEPOW
ER
-20
-20
QUEUESELECTALGORIT
HM
ROUND_ROBI
N
CQIERRORSABSENT
HSPOWERMARGIN
SUPPORTOF16QAM
MAXHSRATE
FALSE
ROUND_ROBIN
TRUE
15
30
HSONLYBESTCELL
HSHYSTERESIS1D
10
10
HSQUALITYESTIMATE
HSTIMETOTRIGGER1D
CPICH_RSCP
640
CPICH_RSCP
640
MAXHSRATE
The HSDPA Iub flow control algorithm adjusts the available bit rate over Iub based mainly on the
maximum possible air interface bitrate received from the scheduler, the number of users in a cell and Iub
congestion indications. The RBS uses the parameter maxHsRate to determine the maximum bit rate to
be used for HS-DSCH data frame traffic in one aggregated bit pipe over Iub.
The parameter maxHsRate should be configured for each RBS to represent the maximum MAC-d PDU
bitrate of HS-DSCH data frames, which is available for the AAL2 path or paths carrying HSDPA traffic to
the RBS in question. The parameter may be set to a MAC-d PDU bit rate of 1.5 Mbps (the default value),
when one dedicated physical E1 link is used for HSDPA traffic. This maximum bitrate level is the same as
the bitrate expressed by the CAPACITY ALLOCATION control frames.
As an example, the default value of this parameter has been obtained by multiplying the HSDPA
available ATM bandwidth (excluding IMA overhead), e.g. 1.92 Mbps, with a factor of 0.79. This factor is
dependent on the average number of MAC-d PDUs per HS-DSCH data frame. In this case, it is based on
having 10 MAC-d PDUs (336 bits) per HS-DSCH data frame in average. It should be noted that
assuming a lower number of PDUs per data frame gives a lower factor and vice versa.
The parameter value of maxHsRate also depends on how the transport network is configured, e.g. if ATM
VC Cross Connect is used or if AAL2 switching is used. It depends on how the ATM VCs etc are
configured, e.g. for HS traffic only, sharing with AAL2 class A and B, several AAL2 paths for HS etc.
Therefore it is recommended to follow the guidelines given by Ericsson regarding transport network
dimensioning before setting a value for this parameter.
16QAM Modulation
The RBS hardware supports both QPSK and 16QAM modulation. However, support of 16QAM is
an optional feature which can be configured on cell level using the parameter supportOf16qam.
The available modulation type impacts the maximum achievable bit rate in the cell,
Maximum Achievable User Bit Rate at the RLC Level As a Function of the UE HS-DSCH Category and Modulation Type