Professional Documents
Culture Documents
Start up Guide
Analytical
and Precision Balances
Analitycal Balances:
• AS X2 PLUS
Precision Balances:
• PS X2
• PS X2.M
• WLC X2
To view a complete User Manual go to the website or scan QR code:
radwag.com/en/manuals/6972
1. CONTENT
fabric dust
Balance Weighing pan Draft shield Centring ring Bottom insert Power adapter* cover
×1 ×1 ×1 ×1 ×1 ×1 ×1
Balance Weighing pan Draft shield Grounding foot Foot Power adapter*
×1 ×1 ×1 ×1 ×3 ×1
Models: PS 3000.X2
Balance Weighing pan Draft shield Grounding foot Foot Power adapter*
×1 ×1 ×1 ×1 ×3 ×1
PS X2.M
2. UNPACKING
1 2 TOP 3
+40 °C Operate the device in a room where the temperature ranges between 10–40 °C
+104°F (50–104 °F) and where the relative humidity is below 80%.
Place the balance on a solid surface to ensure stability. To obtain stable and
+10 °C repeatable weighing results, an anti-vibration table is recommended.
+50 °F
Place the balance away from heat Avoid exposing the balance to a mag- Do not place the balance in a hazard-
sources. Avoid exposing the balance netic field. Do not weigh magnetic ous area. Do not weigh explosive
to the sunlight. substances. materials.
Avoid air drafts and air movements Make sure that the balance is placed Do not place the balance on an
at the workstation. on an even surface. unstable ground exposed to shocks
and vibrations.
1 2
Keep the transport
lock should a warranty
claim or service be
required.
Models: PS X2.M | WLC X2 (d = 1 mg)
1 2
5. COMPONENTS ASSEMBLY
AS X2 (d = 0.01 mg)
1 2 3 4
Models: AS X2 (d = 0.1 mg) | WLC X2 (d = 0.1 mg)
1 2 3
1 Install 2 3
the grounding
foot in a freely
selected
opening.
1 Install 2
the grounding
foot in a freely
selected
opening.
PS X2.M
1 2
Models: PS 3000.X2
1 Install 2 3
the grounding
foot in a freely
selected
opening.
6. PREPARING FOR WORK
up to 8 h
Prior to switching the device on, let Connect the power adapter Connect the power
it reach room temperature (estimated to DC connector. adapter to the mains.
stabilisation time: up to 8 hours).
6.3. Levelling
Press leveling icon. Check the balance level state. The arows shows
how to move the balance foots to level the balance.
To level the balance turn its feet, keep turning Correct leveling screen. Press button
the feet until the level indicator takes central position. to end the operation.
7. PANEL AND SCREEN
Taring Zeroing
Status bar
Parameters Adjustment Header Footer Tare Units Products Operators Autolevel* Databases
printout printout database database
Gross: Tare:
0.00000 g 0.00000 g
Product: User:
Please wait...
1 2
Press “Adjustment” button. Make sure that the weighing pan is empty
and press button to confirm.
3 4
Wait for completion of the start mass Load the weighing pan with mass standard
determination process. and press button to confirm.
5 6
8.2. Zeroing
1 2
Make sure that the weighing pan is empty and press The balance has been zeroed.
“Zeroing” button.
8.3. Taring
1 2
With loaded weighing pan: upon stabilisation The balance has been tared.
of the weighing result, press “Tare” button.
8.4. Working modes / units selection
Press the icon of the current working
mode, to display the list of working
modes.
9. SETTINGS
Gross:
0.00000 g
0.00000 Tare:
0.00000 g
Log out
Admin
Product: User:
Weighing
3 Password
4
1111
Gross:
0.00000 g
0.00000 Tare:
0.00000 g
Product: User:
Admin
Press button to activate numeric keyboard. You have logged as the Administrator.
Enter „1111” password and press button to confirm.
9.2. User settings
Weighing
1 2 Databases
Gross:
0.00000 g
0.00000
Tare:
0.00000 g
Products
Users
0
3 Users
4 New
Code
Password ******
Permissions User
5 6 New
Code
Password ******
Permissions User
Enter user name and press button to confirm. User name has been entered.
Password:
Enter user password
Permissions:
Set respective access level
(user, advanced user, administrator)
9.3. Proximity sensors setup
You can assign the proximity sensors with different functions for each working mode (the sensors will trigger
different operation for each working mode). See the below procedure of sensors setup for the weighing mode.
Weighing
1 2 Parameters
Gross:
0.00000 g
0.00000Tare:
0.00000 g
Adjustment
Working modes
3 Working modes
4 Weighing
Availability Readout
5 Proximity sensors
6 Right sensor
Print footer
Zeroing
Select the appropriate sensor (right or left). Select function that is to be assigned to the
choosen sensor.
Following the above procedure you can configure sensors for other working modes.
10. PERIPHERAL DEVICES CONNECTORS
Power adapter
Computer Printer
Computer Printer
Additional Barcode
display scanner
Keyboard
Prior to cleaning it is necessary to Use soft cloth made of either natural or Apply the cleanser onto the cloth. Mind
disconnect the device from the mains! synthetic fiber exclusively. Avoid using not to apply the cleanser directly onto
Remove the plug from the outlet, cloth made of stiff/hard fabric, this the device!
disconnect all cables. could cause scratches on the surface!
Do not use aggressive cleaning Neither use substances of sharp Make sure that neither dust nor
agents (e.g. solvents, chlorine structure nor intended for liquid gets inside the weighing
preparations, corrosive chemicals, scrubbing. system (device inside).
bleach).
• WEIGHING PANS AND STAINLESS STEEL OR ALUMINIUM COMPONENTS can be cleaned using a cloth slightly
soaked in a solution of water and gentle cleanser (e.g. soap or dishwashing liquid).
• OPERATION PANEL AND HOUSING can be cleaned using a cloth slightly soaked in a solution of water and gentle
cleanser (e.g. soap or dishwashing liquid).
• Dry sample leftovers can be removed using either brush or handheld vacuum cleaner.
• Clean components can be dried using soft cloth or dust-free paper towel, with this the remaining moist will be absorbed.
Press the moldings on the housing and lift the movable element up.
2 3 4
Now you can take out Press the moldings Now you can take out
the front glass. on the housing and lift the upper glass.
the movable element up.
5 6
All disassembled elements are prepared to be cleaned. Assembly all weighing chamber
elements in an order reverse to the disassembly process.
www.radwag.com