Professional Documents
Culture Documents
• The paste should be applied with Putty Blade uniformly on the wall surface in
downward to upward direction to minimize losses.
• After the first coating allow the surface to dry for a minimum of three hours.
• When the first coat has dried, rub the surface gently with hand or soft cloth to
remove any loose particles
Application of Wall Putty
Second coat Application of Wall putty
• Normally two coats are required to get the desired finish. Second coat is to
applies only after the first coat becomes dry.
• Try to limit the total thickness of coating to a maximum of 1.5-2.0mm.
• Wait for at least three days after drying then use fine emery/sand paper to
remove the application marks
• Apply second coat preferably after @ 4 hrs in hot Season & after @ 12 hrs in
cold season. Second coat shall be applied to even out application marks of
1st coat, if any
Coverage & Storage
Coverage-:
• Maximum two coats (Layers) of J.K. Wall Putty.
• Maximum thickness of 1st coat (Layer) 1.5 mm.
• Maximum thickness of 2nd coat (Layer) 1.0 mm.
• Approx achievable coverage is 30 sqft./mm thickness /kg of J.K. wall Putty.
• However, actual coverage achieved depends on the base surface condition &
finished thickness.
Storage-:
• Store JK Wall Putty in a dry place.
• Open bag just Before use
Precautions to be taken
• Although J. K. Wall Putty do not contain any toxic material, use rubber gloves while
mixing.
• Precaution should be taken to avoid dust inhalation while handling putty powder
or during removal of application marks with fine emery paper-say wearing nose
mask.
• Keep the product out of reach of children.
• Once putty paste has hardened, it shall not be used by adding water.
• Life of JK Wall Putty is as long as the life of Grey cement, as it becomes an integral
part of Plaster after application.
Emery paper
Wall Putty Blades
Properties of JK Wall Putty
Cause-:
• Pre wetting is not done Properly
• Exceeds Pot Life of Wall Putty
Remedies-:
• Ensure proper Pre wetting of the
surface before application of Wall
Putty
• Wall Putty should be used within the Chalking of Wall Putty
Pot Life Period ( 2-2.5 Hrs)
• No Extra addition of water should be
done after exceeded Pot life period
Efflorescence
Cause- :
• It occurs due to the presence of water or
moisture in substrate of building materials
• Occurs due to presence of salts in the
Building material.
Remedies-:
• To prevent efflorescence, remove all
powdery substances and thoroughly clean
the surface.
• Ensure that the surface is moisture free,
clean and suitable for application of Wall Due to Efflorescence
Putty.
• Make sure joints and cavities are properly
sealed.
De bonding of wall putty
Cause-:
• Thickness of wall Putty exceeds the
Maximum Thickness
• Improper surface Preparation ( cement
Paint, Moisture etc.) if any.
Remedies-:
• Maximum Thickness of wall Putty should
not be exceeded
• Ensure Proper Preparation of surface
before application of wall Putty. De bonding of Wall Putty from the
substrate
Shrinkage/ Hair Line Cracks
Cause-:
• The movement of contraction and expansion
can cause hairline cracks to appear.
• Not letting cement plaster completely dry
before applying Wall Putty/ paint is actually
quite a common factor attributed to cracks.
Remedies-:
• Ensure Proper Curing of Cement at Plaster
Stage
• Fill The Cracks with some Filler and apply
Wall Putty/ paint over it.
• Before applying Putty or Paint, Make sure
Single Coat of White cement base Primer is Shrinkage/ Hair Line Cracks
applied over the Plaster surface
Some Applications & Finishes of Wall Putty
Finishes on wall Putty