This document compares the 45th and 46th editions of the API Standard 5L specification for line pipe. Some key changes in the 46th edition include deleting two clauses, adding four new clauses around manufacturing capability and API monogram requirements, updating references to other standards, and making minor changes to requirements around end geometry tolerances and guided bend tests. Overall, the changes update and clarify the specification requirements for line pipe.
Original Description:
Original Title
COMPARISON BETWEEN API STANDARD 5L- 45TH & 46TH_REV. 1
This document compares the 45th and 46th editions of the API Standard 5L specification for line pipe. Some key changes in the 46th edition include deleting two clauses, adding four new clauses around manufacturing capability and API monogram requirements, updating references to other standards, and making minor changes to requirements around end geometry tolerances and guided bend tests. Overall, the changes update and clarify the specification requirements for line pipe.
This document compares the 45th and 46th editions of the API Standard 5L specification for line pipe. Some key changes in the 46th edition include deleting two clauses, adding four new clauses around manufacturing capability and API monogram requirements, updating references to other standards, and making minor changes to requirements around end geometry tolerances and guided bend tests. Overall, the changes update and clarify the specification requirements for line pipe.
API STANDARD 5L- 45th EDITION, DECEMBER 2012 API STANDARD 5L- 46th EDITION, APRIL 2018 API STANDARD 5L- 46th EDITION ERRATA 1, MAY 2018 Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Title Specification for Line Pipe Line Pipe Title Effective date API Monographic Effective Date Introduction This Standard is based on This Standard is based on API Spec 5L, 44th edition. API Spec 5L, 45th edition. P. No. VII New annex is added to this New annex is added to this standard is- Specification is- Equations for threaded & PSL2 Pipe Ordered for coupled pipe and Application requiring background equations for Longitudinal Plastic Strain guided bend & CVN test Capacity (Annex N) (Annex P) Title Specification for Line Pipe Line Pipe Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Clause- Units of Clause No. 2.1- Units of This Clause is deleted. Measurement Measurement For data expressed in SI Units, a comma is used as the decimal separator and a space is used as the (Also for data expressed in thousands separator. SI Units, a dot is used as the For data expressed in USC decimal separator.) units, a dot (on the line) is used as the decimal separator and a space is used as the thousands separator.
-- Clause No.4- Terms and Clause No.3- Terms, Definitions Definitions, Symbols and Abbreviations Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION P. No. 8 Total no of definitions are 67. Total no of definitions are 65.
Forward --- Added the following Term:
The term ‘‘may’’ is used to express permission or provision that is optional. Forward --- Added the following Term: The term ‘‘can’’ is used to express possibility or capability. Content --- Added “Figures “and “Tables” information in Contents. ---- --- Clause No.7.2- Additional Information Added following sub-clauses: 33-dual unit marking 59-pipe for longitudinal plastic strain capacity, in which case Anne x N shall apply when specified (see N.2) 61-application of the API Monogram. In which case the requirement of Annex A And Annex O apply. Page No./ API SPECIFICATION API SPECIFICATION Clause No./ Reference 5L- 45TH EDITION 5L- 46TH EDITION Clause No.9.11.3.4 Clause No.9.11.3.4-The local Clause No.9.11.3.4-The local deviation from straight line in the deviation from straight line in the 1,0 m(3.0ft) portion at each pipe 1,5 m(5.0 ft.) portion at each pipe end shall be ≤4,0mm(0.156 in) as end shall be ≤3,2 mm (0.125 in) as shown in Figure 2. shown in Figure 2.
---- Clause No.9.12.1.4-The out of Clause No.9.12.6.3-The out of
squareness, measured as shown in squareness, measured as shown in Figure 3, shall be ≤1,6 mm (0.063in) Figure 3: Reference when using a fixed Square Measurement
---- Nil Added
Clause No.9.12.6-End Squareness Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Clause No.10.2.4.6 The guided bend test shall The guided bend test shall be carried out in be carried out in accordance with ISO 7438 accordance with ISO 5173 or ASTMA370 or ASTMA370 Annex O- Use of API Annex A- API Monogram Monogram by Licensees Program ---- Clause No.O3.2- Deleted Monogrammed Product- Conformance with API Spec Q1 ---- Clause No.O3.3-Application Clause No.A3.2- Control of of API Monogram Application and Removal of the API Monogram Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION ---- Clause No.O3.4-Records Deleted
---- Clause No.O3.5-Quality Deleted
Program changes
---- Nil Added
Clause No.A3.3-Design & Design Documentation
---- Nil Added
Clause No.A3.4- Manufacturing Capability Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Clause No.O4.2 Clause No.O4.2- Product Clause No.A4.2- Product specification identification specification identification The complete API Manufacturers shall mark Monogram marking products as specified by the consists of the following: applicable specification or - The letters Spec 5L standards. Marking shall - The manufacture’s API include reference to the license number applicable API specification - The API monogram and/or standards. Unless - The date of otherwise specified, manufacture (defined reference to the API as the month & year specifications and/or when the monogram is specified when space applied by the allows, the marking may manufacturer) include use ‘’Spec’’ or ‘’Std’’, as applicable (e.g. API Spec 6A or API Std 600). Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION ---- Nil Added Clause No.A4.4-Nameplates ---- Clause No.O4.4- Bundle Deleted identification ---- Clause No.O4.5- Thread Deleted identification ---- Clause No.O4.6- Thread Deleted certification ---- Nil Added Clause No.A4.5-API Monogram Program: Non- conformance Reporting Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Annex A- Specification of Annex M- Specification for welded jointers welded jointers Clause A.1- Method Clause M.1- Method & Qualification ---- Added Clause No.M.2- Process Testing Clause A.2- Workmanship Clause M.3- Workmanship and Inspection Added Clause No.M.4.2 & Figure M.1 Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Title Annex E- Non destructive Annex E- Non destructive inspection for other than inspection for Pipe Not sour service or offshore Required to Meet Annex H,J service or N Hardness Test Hardness testing on parent Hardness testing on parent metal/Weld/HAZ shall be metal shall be performed performed using the using the Vickers test in Vickers test in accordance accordance with ISO 6507-1 with ISO 6507-1 or ASTM or ASTM E92 E384 Pipe Markings ---- HFW full body normalized or full body quenched and tempered pipe Added Location of hardness tests given in Fig. H.1 Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Clause No.J6.4 The local deviation from a Deleted straight line in the 1,0 m (3.0 ft) portion at each pipe end shall be ≤ 3.0 mm (0.120in)
Clause No.J8.2.2 CTOD Test- CTOD Test-
Test pieces shall be taken Test pieces shall be taken from weld metal, the HAZ from weld metal, the HAZ and the parent metal and and the parent metal and shall be prepared in shall be prepared in accordance with ISO 12135, accordance with ISO 12135, ASTM E1290 or BS7448. ISO 15653, ISO 12737, ASTM E1820 or BS7448-1. Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Clause No.J8.3.2.1 Hardness Testing on the Hardness Testing on the parent metal, HAZ & weld parent metal, HAZ & weld shall be performed using shall be performed using the Vickers test in the Vickers test in accordance with ISO 6507-1 accordance with ISO 6507-1 or ASTM E384 or using the or ASTM E92 or using the Rockwell test HR15N in Rockwell test HR15N in accordance with ISO 6508-1 accordance with ISO 6508-1 or ASTM E18. or ASTM E18. Fig.J1 d) ----- Added Figure J.1 (d)- Location of Hardness Tests HFW full normalized or full- body quenched and tempered pipe. Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Fig.J1-Key a- Weld Centreline a- Weld centreline; for Figure J.1 d) (Full-body normalized or quenched and tempered), a position is centre of bond plane when visible; if bond plane is not visible, centre on mid width of ID trim edges. Annex K- Title Non-destructive inspection Non-destructive inspection for pipe ordered for sour for pipe ordered for sour service and/or offshore service, offshore service, service and/ or Service Requiring Longitudinal Plastic Strain Capacity Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Clause No.K.2.2.2 Suspect pipe shall be dealt with in Suspect pipe shall be dealt with in accordance with the applicable accordance with the applicable standard for non-destructive standard for non-destructive inspection of pipe, unless otherwise inspection of pipe, unless otherwise stated in this annex, Annex H or stated in this annex, Annex H, Annex J, whichever is applicable. Annex J or Annex N whichever is applicable. Clause No.K.2.2.2 For offshore service, individual For offshore service and service laminations and/or lamination requiring longitudinal plastic strain densities exceeding the acceptance capacity, individual laminations limits for offshore service given in and/or lamination densities Table K.1 shall be classified as exceeding the acceptance limits defects. If agreed, compliance with given in Table K.1 shall be classified such requirements shall be verified as defects. If agreed, compliance by ultrasonic inspection in with such requirements shall be accordance with ISO 10893-8 verified by ultrasonic inspection in (except 4.2), ASTM A435 or accordance with ISO 10893-8:2011 ASTMA578. (except 4.2), ASTM A435 or ASTMA578. Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Table K.1 Strip/plate edges or areas Strip/plate edges or areas adjacent to the weld seam adjacent to the weld seam Service Condition- Sour or Service Condition- Sour, offshore offshore or longitudinal plastic strain capacity. Annex M Removed Added- Annex M (normative) Specification for Welded Jointers Annex N Page intentionally blank Added- Annex N PSL2 Pipe Ordered for Applications Requiring Longitudinal Plastic Strain Capacity Annex O- Title Use of the API Monogram Additional Information for Licensees Use of the API Monogram by Licensees Page No./ API SPECIFICATION 5L- API SPECIFICATION 5L- Clause No./ Reference 45TH EDITION 46TH EDITION Clause No.O.1- Scope Deleted Clause No.O.2- References Deleted Clause No.O.3- API Deleted Monogram Program: Licensee Responsibilities