You are on page 1of 25

ISAM-V : R4202v Features

Dec 2010

All Rights Reserved © Alcatel-Lucent 2007


R4202V : Overview

id BriefDescription Customer
H248 Features

ALU00815991 ISAM-V H248 ISDN BA : Stable call preservation at SIGTRAN switchover Telekom Austria
SIP Features

ALU00754323 ISAM-V SIP : External Path Forwarding (Lawfull Intercept) BskyB

ALU00123613 NANT-E Support for SIP L4 Voice


GPON Features
ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI VoIP provisioning.
ALU00123590 OISG Implementers' Guide V2

All Rights Reserved © Alcatel-Lucent 2007


H248 Features

All Rights Reserved © Alcatel-Lucent 2007


ALU00815991 ISDN BA - Stable call
preservation at SIGTRAN switchover

All Rights Reserved © Alcatel-Lucent 2007


ALU00815991 ISDN BA - Stable call preservation at SIGTRAN switchover

 Requirement:
 Stable call preservation on ISDN BA boards at SIGTRAN switchover
 Q.931 messages from subscribers involved in stable calls must be queued
during the switchover period
 No new outgoing ISDN BA calls are supported during SIGTRAN switchover
 After the SIGTRAN switchover, new incoming & outgoing ISDN calls can be made
successfully

 Customer: Telekom Austria

 FDT 3HH-09840-AAAA-ADZZA
All Rights Reserved © Alcatel-Lucent 2007
ALU00815991 ISDN BA - Stable call preservation at SIGTRAN switchover

 Implementation:
 The recovery time, Tr implemented via the IUA timer defined in CDE profile
 iua_param trafficmode minasp pendtime. Example: iua_param 1 1 4
 Traffic mode: 1=over-ride (one active ASP), 2 =load-sharing (several
active ASPs), Default: 1
 MinASP: Minimum number of active ASPs, Default: 1
 PendTime: ASP maximum transition time from Inactive to active, Default:
4 seconds (Tr <= 5s)
 If active ASP becomes inactive, start the recovery timer and buffer Q.931
messages. (ISDN terminations will not be put into OOS)
 If one ASP becomes active before the Tr expires, send all the queued messages
to the active ASP
 When ASP switch to AS-Down i.e. Tr expires, reset ISDN terminations and clear
the buffer
 Unacknowledged/unsent packets by original SCTP association will not be
retrieved and resent by IUA

All Rights Reserved © Alcatel-Lucent 2007


ALU00815991 ISDN BA - Stable call preservation at SIGTRAN switchover

 ASP Fail-over case for CS2K, Telekom Austria: SCTP restart


 MGC support of multi-homing where the active and standby SG’s of the MGC are
serviced by single ‘active’ IP address. Upon switchover from one SG to the other, the
SG which is taking activity will re-initiate the SCTP link and IUA association setup.

All Rights Reserved © Alcatel-Lucent 2007


SIP Features

All Rights Reserved © Alcatel-Lucent 2007


ALU00754323 SIP - External Path
Forwarding (Lawful Intercept)

All Rights Reserved © Alcatel-Lucent 2007


ALU00754323 SIP - External Path Forwarding (Lawful Intercept)

 Requirement:
 The ISAM-V SIP support of the feature External Path Forwarding on the POTS
line boards
 EPF enable/disable mode is configurable per VLAN
 IP@ of EPF router is configurable via CLI
 This feature will be supported per the following ISAM-V SIP configurations:
 NANT-A, Switched network topology
 Shared VOICE VLAN (RTP and SIP) and distinct VLAN (EPF enabled on the
RTP VLAN, EPF has not to be enabled on SIP VLAN)
 Centralized SIP architecture
 Hub node and Subtending nodes
 All Equipment practices (e.g. FD-7302, FD-7330, SB-REM,...)

 Customer: BskyB
All Rights Reserved © Alcatel-Lucent 2007
ALU00754323 External Path Forwarding (Lawful Intercept)

 Implementation:
 In case “external forwarding” is enabled, all upstream traffic within this VLAN
(voice) is forwarded to the EPF destination IP address
 A single IP address can be configured as EPF destination IP address
 EPF destination IP address must belong to a directly attached subnet (IP address
shall be of IP NEXT HOP)

 CLI:
 configure interface shub ip <vlan id> extfwd device-ip <x.x.x.x>
<vlan id> = Voice Vlan
<x.x.x.x> = external voice forwarding ip

All Rights Reserved © Alcatel-Lucent 2007


ALU00754323 External Path Forwarding (Lawful Intercept)
 CLI Example:
Voice VLAN for RTP
configure vlan shub id 4092 mode voice-vlan name RTP-VLAN
configure vlan shub id 4092 egress-port lt:1/1/5
configure vlan shub id 4092 egress-port network:0
configure ip shub vrf 1 name VoiceVRF fast-path-mode:ena-user-user-com
configure interface shub vlan-id 4092
configure interface shub ip 4092 vrf-id 1
configure interface shub ip 4092 ip-addr 10.178.131.24/18
configure interface shub vlan-id 4092 admin-status up
configure ip shub vrf 1 route-dest 0.0.0.0/0 next-hop 10.178.128.1 vlan-id 4092

External Packet Forwarding


configure interface shub ip 4092 extfwd device-ip 10.178.128.1

All Rights Reserved © Alcatel-Lucent 2007


ALU00123613 NANT-E Support for
SIP L4 Voice

All Rights Reserved © Alcatel-Lucent 2007


ALU00123613 NANT-E Support for SIP L4 Voice

 Requirement:
 NANT-E support for SIP L4 Voice
 NANT-E feature parity with NANT-D for ISAM Voice in R42. SIP L4 voice forwarding
should be supported. Basic Call, Fax and modem calls can be supported with NANT-E
without external clock reference.

 Implementation:
 No additional SW development was done
 Test-only feature

All Rights Reserved © Alcatel-Lucent 2007


GPON Features

All Rights Reserved © Alcatel-Lucent 2007


ALU00709642 Parallel Support Of ALU
Legacy VoIP provisioning and OMCI VoIP
provisioning

All Rights Reserved © Alcatel-Lucent 2007


ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

 Requirement:
 Parallel methods for supporting VoIP provisioning are required:
 OMCIv1 proprietary method (R4.2)
 OMCIv2 standardized method (R4.2.02)
 TL1 and CLI support
 SIP and Megaco support
 Notes:
 ALU00123590 OISG Implementers' Guide V2 is duplicate RCR
 ONT RCR: ALU00804616 Parallel Support Of ALU Legacy VoIP provisioning and
OMCIv2 VoIP provisioning - ONT.

 FDT: 3HH-08803-AAAA-ADZZA

All Rights Reserved © Alcatel-Lucent 2007


ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

 OMCIv2 SIP CLI example:

configure equipment ont interface 1/1/4/4/1 sw-ver-pland 3FE52258AIBA20 sernum


ALCL:F9ACDB88 p2p-enable enable voip-allowed iphost
configure equipment ont interface 1/1/4/4/1 admin-state up
configure equipment ont slot 1/1/4/4/1/1 planned-card-type 10_100base
plndnumdataports 4 plndnumvoiceports 0
configure equipment ont slot 1/1/4/4/1/2 planned-card-type pots plndnumdataports 0
plndnumvoiceports 2

configure qos profiles bandwidth VOICE committed-info-rate 160 assured-info-rate 160


excessive-info-rate 160 delay-tolerance 8
configure qos interface ont:1/1/4/4/1 us-num-queue 4
configure qos interface 1/1/4/4/1/voip upstream-queue 0 priority 8 weight 100
bandwidth-profile name:VOICE bandwidth-sharing ont-sharing

All Rights Reserved © Alcatel-Lucent 2007


ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

configure bridge ageing-time 7200 ; Avoid Mac aging


configure bridge port 1/1/4/4/1/voip
configure bridge port 1/1/4/4/1/voip vlan-id 100 ; residential-bridge
configure bridge port 1/1/4/4/1/voip pvid 100

configure iphost ont ont:1/1/4/4/1/1 dhcp-dscp 24 vlan 100 dhcp enabled


configure iphost ont ont:1/1/4/4/1/1 admin-state up

configure voice ont voip-config ont:1/1/4/4/1/1 protocol sip


conf-method omci securiprof 41

configure voice ont uri-prof 1 name SIP_URI address ims.belab.com ; Registar domain
configure voice ont uri-prof 2 name SIP_AOR address ims.belab.com ; User domain
configure voice ont uri-prof 11 name XML_Address address ; XML profile
"ftp://guest:guest@10.176.5.5/inea_ed01.xml"
All Rights Reserved © Alcatel-Lucent 2007
ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

configure voice ont auth-sec-prof 1 name AUTH_SIP ; sip user auth


validation-scheme md5-digest realm ims.belab.com
configure voice ont auth-sec-prof11 name XML_Address_Auth ; ftp server auth
validation-scheme basic-authentic user-name guest password guest

configure voice ont sec-uri-profile 31 name SIP_REGISTRAR_Profile


auth-securi-prof 1 uri-prof 1
configure voice ont sec-uri-profile 41 name XML_Profile_1 auth-securi-prof 11
uri-prof 11

configure voice ont rtp-profile 1 name RTP_Profile_1 dscp 46


configure voice ont voice-serv-prof 1 name SERVICE_Profile_1 securi-prof 41
hook-flash-min 75 hook-flash-max 300 pstn-variant 48
; pstn variant = country

All Rights Reserved © Alcatel-Lucent 2007


ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

configure voice ont voip-media-prof 1 name Voip_Media_1 voiceserviceprof 1 rtp-prof 1


fax-mode passthru codec1st pcmu codec2nd g729 pkt-period1st 20 pkt
period2nd 20 silence1st off silence2nd off outofband-dtmf enabled

configure voice ont voip-app-service 1 name Voip_Appl_Service_1 calling-number


enable call-waiting disable do-not-disturb enable call-hold enable call-park enable
three-way-calling enable call-transfer enable

configure voice ont feat-acccode-prof 1 name Voip_AccesCodes_1 act-caller-id "" deact-


caller-id "" act-dnd "" deact-dnd "" dnd-pin "" emergency "" intercom 0 attend
call-trans "" blind-call-trans "" cancel-call-wait *70 hold *52 park "“

configure voice ont sip-config ont:1/1/4/4/1/1 proxyserv-prof 1 outproxyserv-prof 1


primary-dns 10.176.5.5 reg-expire-time 3600 re-reg-head-start 360
aor-host-prt-prof 2 registrar-prof 31 soft-sw-vendor THIN
uri-format sip-uri dscp 24
; soft-sw-vendor THIN Thightly-Coupled
All Rights Reserved © Alcatel-Lucent 2007
ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

configure voice ont voice-sip-port 1/1/4/4/1/2/1 user-aor +3227530101 display-name


+3227530101 val-scheme md5-digest user-name 27530101password 1234 realm
ims.belab.com app-serv-prof 1 ac-code-prof 1
configure voice ont voice-sip-port 1/1/4/4/1/2/2 user-aor +3227530102 display-name
+3227530102 val-scheme md5-digest user-name 27530102 password 1234 realm
ims.belab.com app-serv-prof 1 ac-code-prof 1

configure voice ont voice-port 1/1/4/4/1/2/1 custinfo User1 voipconfig sip pots-pwr-timer
300 call-hist disable pwr-override false rx-gain 1 tx-gain 2 impedance 600 voip-media-
prof 1 admin-state unlocked
configure voice ont voice-port 1/1/4/4/1/2/2 custinfo User2 voipconfig sip pots-pwr-timer
300 call-hist disable pwr-override false rx-gain 1 tx-gain 2 impedance 600 voip-media-
prof 1 admin-state unlocked

OMCIv2 XML
example

All Rights Reserved © Alcatel-Lucent 2007


ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

 OMCIv1 SIP CLI example:

configure equipment ont interface 1/1/1/4/1 sw-ver-pland 3FE52258AICA09 sernum


ALCL:F9ACDB88 p2p-enable enable voip-allowed enable
configure equipment ont interface 1/1/1/4/1 admin-state up
configure equipment ont slot 1/1/1/4/1/1 planned-card-type 10_100base
plndnumdataports 4 plndnumvoiceports 0
configure equipment ont slot 1/1/1/4/1/2 planned-card-type pots plndnumdataports 0
plndnumvoiceports 2

configure qos profiles bandwidth VOICE committed-info-rate 160 assured-info-rate 160


excessive-info-rate 160 delay-tolerance 8
configure qos interface ont:1/1/1/4/1 us-num-queue 4
configure qos interface 1/1/1/4/1/voip upstream-queue 0 priority 8 weight 100
bandwidth-profile name:VOICE bandwidth-sharing ont-sharing

All Rights Reserved © Alcatel-Lucent 2007


ALU00709642 Parallel Support Of ALU Legacy VoIP provisioning and OMCI
VoIP provisioning

configure bridge port 1/1/1/4/1/voip


configure bridge port 1/1/1/4/1/voip vlan-id 306 ; residential-bridge vlan
configure bridge port 1/1/1/4/1/voip pvid 306

configure voice ont service 1/1/1/4/1/1 dhcp enabled ftp-serv-ip-addr 10.176.5.5


ftp-user-name guest ftp-passwd guest conf-file-name
INEA-ONT-1-1-1-4-1-1_ed20.xml vlan 306 voip-mode sip2 admin-state unlocked
; sip1 Thightly-Coupled
; sip2 Loosely-Coupled

configure voice ont pots 1/1/1/4/1/2/1 admin-state unlocked


configure voice ont pots 1/1/1/4/1/2/2 admin-state unlocked

OMCIv1 XML
example

All Rights Reserved © Alcatel-Lucent 2007


www.alcatel-lucent.com

All Rights Reserved © Alcatel-Lucent 2007

You might also like