Professional Documents
Culture Documents
Nội dung
• Giới thiệu
• Khuếch đại
• Push-Pull Amplifiers
• Khuếch đại đầu ra dùng BJT
• Using Negative Feedback to Reduce the Output Resistance
• Summary
CMOS Analog Circuit Design, 3rd Edition Reference
Pages 236-247
GIỚI THIỆU
General Considerations of Output Amplifiers
Yêu cầu: VDD
Phân loại i1
Current
1.) Chế độ A
t
2.) Lặp cực nguồn i2=IQ iOUT
3.) Push pull Class AB
i1
4.) Substrate BJT amplifiers iOUT
Current
5.) Amplifiers using negative i2 t
Class B
shunt feedback i1
Current
iOUT
t
i2
Fig. 5.5-005
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Suy ra:
Fortunately, the maximum current for the resistor and capacitor do not occur at the same
time.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
vOA(t) RL v (t)
vOUT (t)
RL+Rout OA
Volt
=
Output
s
Amplifier
vIN Rout
t
vOA
RL vOUT
070422-02
Giải pháp
1.) Sử dụng tụ ghép cặp
2.) Xác định lại điểm mát (VDD/2).
3.) Sử dụng dc coupling for split power supplies.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
CHẾ ĐỘ A
Inverter tải nguồn dòng
Chế độ A: Dòng qua
MOSFETs trong toàn bộ chu
kì của tín hiệu
Đặc điểm:
• Không đối xứng sink và
source
• Tuyến tính
• Hiệu suất nhỏ
Hiệu suất:
Assume that KN’=2KP’=100µA/V2, VTN = 0.5V and VTP = -0.5V. Design the W/L ratios
of M1 and M2 so that a voltage swing of 1V and a slew rate of 1 V/s is achieved if
RL 1 k and CL 1000 pF. Assume VDD = |VSS| 2V and VGG2 0V. Let L = 1 m and
assume that Cgd1 = 100fF. Find the voltage gain and roots of this output amplifier.
Solution
Let us first consider the effects of RL and CL.
iOUT(peak) = ±1V/1k = ±1000µA and CL·SR = 10-9·106 = 1000µA
W1 2(IOUT-+IQ) 4000
Since the= current for CL and RL=occur 3µm
at different
≈ times, choose a bias current of 1mA.
L1 KN’(VDD+|VSS| -VTN)2 100·(3.5)2 1µm
and
W2 2IOUT+ 2000
=
L2 KP’(VDD-V 2 = 2 ≈ 1µm
18µm -|V
GG2 TP |) 50·(1.5)
The roots are, zero = gm1/Cgd1 1.23GHz and pole ≈ 1/(RLCL) -159.15
kHz
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Méo sóng hài băng thông rộng
The linearity of an amplifier can be characterized by its influence on a pure sinusoidal
input signal. Assume the input is,
Vin() Vp sin(t)
The output of an amplifier with distortion will be
Vout() a1Vp sin (t) a2Vp sin (2t) ... anVp sin(nt)
Harmonic distortion (HD) for the ith harmonic can be defined as the ratio of
the magnitude of the ith harmonic to the magnitude of the fundamental.
For example, second-harmonic distortion would be given as
a2
HD2 a1
Total harmonic distortion (THD) is defined as the square root of the ratio of the sum of
all of the second and higher harmonics to the magnitude of the first or fundamental
2 2 2
[a2 a 3... a ]n1/2
Thus, THD can be expressed as THD a1
The distortion of the class A amplifier is good for small signals and becomes poor at
maximum output swings because of the nonlinearity of the voltage transfer curve
for large-signal swings.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Mạch lặp cực nguồn chế độ A
- Mạch lặp cực nguồn chế độ A có trở kháng ra nhỏ và ít suy hao tín hiệu.
Đặt:
Nếu VDD = 2.5V, N = 0.4V1/2, VTN1= 0.7V, and VON1 = 0.2V, then vOUT’(max) = 3.661V
Và:
vOUT(max) = 3.661-2.5 = 1.161V
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Maximum Sourcing and Sinking Currents for the Source Follower
- Dòng source lớn nhất (into a short circuit):
Giả sử các trans bão hòa và:VDD = -VSS = 2.5V
Ta được:
- Nếu VDD = -VSS = 2.5V, Vout = 0V, W1/L1 = 10m/1 m, W2/L2 = 1m/1 m,
ID = 500 A, thì:
For the current sink load follower (RL = ):
Nếu bỏ qua hiệu ứng bulk thì
Trong đó:
Sự hiện diện của điểm không ở LHP dẫn tới khả năng trong hầu hết các trường hợp
các điểm không và điểm cực sẽ dẫn đến một số suy hao bậc cao
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
- Hiệu suất:
Dựa vào cách phân cực cho trans
• Class B - one transistor has current flow for only 180° of the sinusoid (half period)
Nhận xét:
• vOUT không thể đạt tới giá trị của VDD and VSS
• Tồn tại méo đáng kể tại vIN =0V với mạch Class B push-pull follower
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Hoạt động tín hiệu nhỏ Push-Pull Follower
Mô hình:
- Nếu VDD = -VSS = 2.5V, Vout = 0V, ID1 = ID2 = 500µA, and W/L = 20µm/2µm, Av = 0.787
(RL= and Rout = 448.
- Điểm không và điểm cực:
Các nghiệm này đều ở tần số cao do các trở kháng nhỏ.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Push-Pull, Common Source Amplifiers
Tương tự như chế độ A nhưng có thể hoạt động ở chế độ B cho hiệu suất mạch cao
VDD
M2
VTR2 iOUT
vIN vOUT
VTR1
M1CL RL
Fig. 060-04
VSS
Nhận xét:
• VTR1 và VTR2 điều khiển dòng phân cực cho M1 và M2.
• Hiệu suất tương tự như mạch the push-pull, source follower.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Illustration of Class B and Class AB Push-Pull, Inverting Amplifier
Output current and voltage characteristics of the push-pull, inverting amplifier (RL =
1k):
Nhận xét:
• vOUT không thể đạt được giá trị VDD and VSS
VDD
M5 M6
M1 M3 VGG3
iOUT
vIN vOUT
M2 M4 VGG4
CL RL
M7 M8
Fig. 060-05
VSS
- VGG3 and VGG4 có thể phân cực cho mạch này ở class AB hoặc class B
- Dòng phân cực của M6 và M8 không phụ thuộc vào VDD or VSS (giả sử VGG3 and
VDD
VDD -VT+VSat
VDD
IBias
VDD -VT+2VSat
VT+2VSat vIN
vIN 050423-10
050423-08
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
MẠCH KHUẾCH ĐẠI ĐẦU RA DÙNG BJT
What about the use of BJTs?
Nhận xét:
• Có thể sử dụng cả BJT
nền hoặcl ateral BJTs.
• Trở kháng ra tín hiệu nhỏ là 1/gm có thể nhỏ hơn100.
• Unfortunately, only PNP or NPN BJTs are available but not both on a standard CMOS
technology.
• BJTs will cause substrate current unless they surrounded by a deep well
• Để có sink dòng hay source dòng lớn, dòng iB, phải lớn. Việc dòng lớn khi điện áp đạt
giá trị tới hạn đối với mạch Mosfet là khó khăn.
• Nếu xem xét trình điều khiển MOSFET, thì cực E chỉ có thể ở giá trị vBE + VON của
nguồn cấp. Giá trị này có thể là 1V hoặc hơn.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Trở kháng ra nhỏ: BJTs
- Trở kháng ra của tầng BJT chế độ A là:
Lưu ý: số hạng thứ 2 phải nhỏ hơn 1/gm1 để đạt trở kháng ra
nhỏ nhất có thể
- Giá trị thực tế của Rout sẽ bị ảnh hưởng bởi RL, particularly if it is small.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Push-Pull Implementation
rds1||rds2
Rout = 1+Loop Gain
Nhận xét:
• Trở kháng ra có thể nhỏ cỡ10.
• Nếu bộ khuếch đại sai số không cân bằng thì khó điều khiển dòng tĩnh ở M1 and M2
• Tính tuyến tính cao do phản hồi mạnh
• Hiệu suất cao nếu hoạt động ở class B or class AB
• We will consider this circuit in more detail in a later lecture.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
Tăng độ hỗ dẫn ở mạch Source Follower
The following configuration allows the output resistance of the source follower to be
decreased by a factor of K, where K is the current ratio between M4 and M3.
LECTURE 21 – KHUẾCH ĐẠI ĐẦU RA
TỔNG KẾT
• The objectives are to provide output power in form of voltage and/or current.
• In addition, the output amplifier should be linear and be efficient.
• Low output resistance is required to provide power efficiently to a small load resistance.
• High source/sink currents are required to provide sufficient output voltage rate due to
large load capacitances.
• Types of output amplifiers considered:
Class A amplifier
Source follower
Class B and AB amplifier
Use of BJTs
Negative shunt feedback