Professional Documents
Culture Documents
S0
O CKET M ETER
RECORDER
EM
Advanced Metering Infrastructure (AMI) has reached new heights with
920
revitalize legacy applications
TM to rapidly and cost-efficiently respond to
SATEC’s latest introduction in energy and power quality measurements changing market conditions.
for smart grid deployments.
The Model EM920 eXpertmeter is an advanced energy meter
that exceeds Class 0.2S class revenue billing requirement. It
The SATEC
analyzer in aModel
socketEM920 eXpertmeterTM
meter with is an advanced
precise measurement and energy
provides long term power
includes advanced memory for load
quality & trend
analysis profiles,
to detect andand
record
expansion capabilities.
The EM920’s unique “Add-On” modularity is the key to its waveform events and fault currents harmful to power systems.
remarkable versatility and unprecedented effort to add
The Model EM920 eXpertmeterTM provides a real-time view into
intelligence, control and communications to electrical metering. a greater volume of data than a standard energy meter, leading
SATEC’s “Add-On” module concept allows you to configure the
to faster analysis and better decision-making all around.
meter to your changing needs, thus saving valuable time in the Customers benefit from better access to information—while
field or future costly replacements. Technological advancements
providing better service that costs less.
Application
s
The EM920 eXpertmeterTM Series is used in electric utility inter-ties, Multiple simultaneous communications allow communication
any electrical substation where precise information via MODBUS, DNP3.0, and MV90 while retrieving power
is required for planning purposes, and monitoring primary customers on quality events such as SAG/SWELL and transient detections.
the service entrance to provide a higher service in quality of power.
View Harmonic conditions locally to determine the cause
of problems by utilizing its unique “Directional” Harmonics
isInstall at legacy
currently substations
provided. whereexisting
Just replace little to socket
no information
meter and
Power flow.
instantly provide information previously unattainable.
View real time Oscillography and determine quality of power
Long term monitoring and storing capabilities allow for
many months of information storage. Record Time Of Use Multiple levels
unauthorized of password protection to prevent
access
(TOU), load profile, Min/Max, custom reports etc.—essential
information used for planning and maintenance engineers. Time synchronization (IRIG-B, Ethernet SNTP) with 1 mSec
accuracy
2
F
eature s
to configure and
Modularity: Add-On module support
change with your growing needs, instead of requiring complete
assemblies that can only be changed at the factory
Advanced
recorders) Power Quality waveform recording (4 waveform DEVICE
CONFIGURATION
Selectable 32-1024 samples per cycle
Performance resolution quality graphical screen
High Speed Transient detection as little as 17 μs @ 60Hz
Easy interface with any existing SCADA or EMS system
Exceeds EN 50160 Standards
Rigid design for use in harsh environments Anti-tampering
Exceeds IEC 61000-4-7; IEC 61000-4-15 and IEC 61000-30
and self test functions
ITI (CBEMA) curves
Standard USB, RS485 and IR port
Transformer Line/Loss compensation and up to 8 points
Transformer correction (VT, CT) MODBUS, DNP3.0 and MV90 compatible
TRM Slot
(Transient Module)
COM Slot
(Communication Module)
I/O Slot
(Input/Output Module)
APS Slot
(Auxiliary PS Module)
3
High Performance
Revenue Meter
The EM920 is a high precision, multi-purpose 4 quadrant by a modular architecture. This modularity also offers a full
meter used for active, reactive, and apparent energy / freedom of choice for deployment of new technologies. The
demand measurement and recording. The meter is ideal for device supports multiple communication protocols.
grid applications in generation, transmission and distribution
utilities. Designed for major industrial and commercial
RT ENERGY
consumers as well. Accuracy class 0.2S approved according to TOTAL IMPO
ANSI C12.20 class 10/20 and to IEC 62053-22 class 0.2S, and REPORT
designed according to even more rigorous SATEC standards.
4 seasons).
phaseThe
instrument
meteringalso
provides
three power with voltage,multi-functional
current (including
measured
frequency, neutral current), unbalance,
voltage/current power, energy,
loadpower factor,
profile, and other
measurements
logged with realon-board. More than 100 parameters can be
time stamps.
The EM920iniswide
equipped
range with
high resolution 4”Real
LCD Time
display
operating temperature, offering
The EM920
Allisnecessary
equippedcommunication
with anti-vandalism and anti-tampering
features. applications are covered
T ENERGY
TOU IMPOR
REPORT
Meets 0.1% Revenue Accuracy (tested to 0.05%) High precision 3-phase power meter
Active energy: class 0.2S precision ANSI C12.20 class 10/20 Voltage
4
High Performance
Revenue Meter
POWER
VOLTAG
E
CURREN
T
5
Power Quality
Analyzer
Cutting Edge Power Quality Analyzer & Fault Recorder
The EM920 is among the most advanced power quality analyzer and data log with waveforms (3 voltage and 4 current inputs for waveform
recorder on the market. The instrument is a product of SATEC’s 20 years of recording) available for detailed Power Quality event analysis. The
experience in the creation of power quality instruments. The EM920 is individual harmonics and inter-harmonics are analyzed according to
designed to fully comply with the most demanding industry standard, IEC IEC 61000-4-7. The instrument also supports directional power
61000-4-30 Class A. It provides power quality reports and statistics harmonics analysis. The flicker is measured and analyzed according to
according to EN 50160, complimented by comprehensive power quality IEC 61000-4-15.
event/
Power quality analysis and reading Harmonic energies to determine quality of power received or delivered
6
Power Quality Events
Via PAS Software
DIRECTIO PQ LOG
NAL
HARMONIC
S
VOLTAGE VOLTAGE
TIO
DIP INTERRUP
N
CBEMA CU
RVE
EPORT
SPECTRUM
GRAPH & 160 COMPLIANCE R
TABLE EN 50
7
Fault & Transient
Recorder
The EM920 provides state-of-the-art fast transient recording capability. (withstands up to 6 kV). Four voltage waveforms (3 phases and neutral
Transient pulses as short as 17 microseconds can be reliably recorded and relative to the ground) are recorded at 1024 samples/ cycle to complement
analyzed. The EM920 can record such short pulses by a separate the waveforms recorded by the power quality channel.
electronic channel with a sampling rate of 1024 samples/cycle. The The fault recorder provides 4 measured and recorded currents (including
transient amplitude is recorded relative to the ground in accordance with measured neutral current) up to 50A (10 I n). The event
the strict definitions of power quality standards (EN 50160). The
log is complemented by a fault log and full length waveform
instrument can measure transient pulses with an amplitude of up to 2 kV
recording.
SHORT TRAN
SIENT
EVENTS
OSCILL
ATORY
Infrared port (Modbus RTU/ASCII and DNP3.0 protocols). Instrument firmware easy upgrade, using SATEC Power
Supports IEC 62056-21/61 standard—hardware and Analysis Software (PAS) via any communication port
RS485
bps, universal
Modbus serial communications
RTU/ASCII port (up to 115,200
and DNP3.0 protocols) INPUT/OUTPUT
Two (2) independent digital inputs for Synchronization/
OPTIONAL ADD-ON I/O & COMMUNICATION Breaker Status/Counter functions—includes fast 1 kHz
MODULES sampling rate
State-of-the-art communication abilities enabled by the EM920 KYZ relay output (Form C contact)
concept:
Optional module with 8 digital inputs used for breaker status
or pulse counting
Ethernet 10/100
upBase-T
to fiveport
(Modbus/TCP or DNP3.0/
TCP protocols), non-intrusive simultaneous
Optional
AC/0.2A@Module
for&64relay outputs. 2 Form A (5A @ 250V
250V AC) FORM C (0.15A @ 250V AC/DC)
connections, Telnet service port and RS232/485 user versatile
port
Optional
±1mA and4CH
Analog output module. 0-20mA, 4-20mA,
0-1mA
1-ms satellite-synchronized clock—IRIG-B format timecode
input
AC/DC AUX. PS module: 50-288V AC, 90-290V DC
Supports SNTP synchronization and cross trigger of events
DC/DC AUX. PS module: 24-48V DC
Dial Up modem module, (Modbus & DNP3.0 protocol) up to
56 kb/s
MV 90
1000 Ft Max
Ethernet / Modem
MODE
SCADA RS48 RS48 RS48
DNP3.0 / 5 5 5
MODBU
S 120 W 120 W
Tx (+) / Rx (+)
Tx (-) / Rx (-)
(CONNECT UP TO 8 DEVICES)
9
Standards Compliance
Specifications
ACCURACY Magnetic Field: ANSI C12.1
ANSI C12.20: Class 10/20: EFT/B: IEC 61000-4-4: level 4—4kV AC lines and 2kV I/O and
COM lines
0.2S IEC 62053-22: Class 0.2S
SWC: IEEE/ANSI C37.90.1—2.5kV—measuring inputs, I/O and
COM
POWER
QUALITY ESD: IEC 61000-4-2: level 4—15kV air discharge
Harmonics and interharmonics measurement: IEC 61000-4-7
class I Radiation Susceptibility: ANSI C12.1
1
0
Measurement
Specifications
ParameterFull Scale@ Input Range
Accuracy Range
% Reading % FS Conditions
Reactive power 3xV FSxCT/1000 0.3|PF|≥0.5, I≥2% FSI 10,000,000 kvar to +10,000,000 kvar
3.0200%-1000% FS
Symmetrical Voltage FS 1 degree* As voltage
components
Current FS As current
Current FS ±180.0
Phasor
angles
* @80% to 120% of voltage FS, 2% to 200% of current FS and frequency 50/60 Hz.
Physical
Dimension
s
1
1
Technical
Specifications
AC Voltage Inputs 3 voltage and 1 neutral inputs 50/60Hz High input impedance > > 10MΩ
Rated impulse
(ANSI C12.1 voltage
& IEC 62052-11, protective class II) 6000V peak
Starting voltage
0.1%U
n
Burden per phase
< 0.5 VA
Overload withstand
22, protective for 1 minute phase-to-ground (IEC 62053-
class II) 4000V AC
Rated C12.1
(ANSI impulse voltage
& IEC 62052-11, protective class II)
6000V peak
Terminals for wires size
Starting voltage, interruptions and dips measurement applicable only with installed APS
1
1
2
Technical
Specifications
Fast Status Input Digital Input optically isolated
2DI (standard) Dry contacts, internally wetted 24V DC
8DI
Optional module Resistance of open contact sensing > 1MΩ
Operation time 1 ms
Release time 1 ms
Release time 1 ms
Non-linearity 0.2%
Accuracy 0.5%
1
3
Technical
Specifications
Communication Ports
COM1 Built-in Infra Red communication port Display unit
IR port (Standard) RS232 communication, TTL level, max baud rate 19.2 kb/s
Protocols Modbus RTU/ASCII and DNP3.0
GSM/GPRS module— RS232 communication, TTL level, max baud rate 115.2 kb/s
Optional
GSM/GPRS module Quad Band GPRS class 10
Protocols MASTER
DNP3.0 (Phase II) / SLAVE Modbus RTU/ASCII and
1
4
Technical
Specifications
Display Unit 4" Graphic LCD Display 320x240 dots
Volatile Memory For energy and tariff registers logging, EV-PQ-DATA-WV log 1
Operational temperature
Environment Optional LCD Operational temperature -40°C to 75°C
Temperature
-20°C to 70°C
Storage temperature
-40°C to 85°C
1
5
EM920 ORDER STRING
EM
MODEL
920
EM920—Form 9S
EM920
(includes 2DI, 1KYZ relay, USB, RS485 port)
OPTIONS
VOLTAGE INPUTS
Standard - 120 up to 277 Volts AC (L-N) ± 20%
(208 to 480 volts L-L) -
(cannot be combined with auxiliary power supply)
Low to
100 Voltage 57.73
208 Volts up via
(L-L) to 120
PT Volts (L-N), U
CURRENT
INPUTS
5 Ampere 5
1 Ampere 1
CALIBRATION AT FREQUENCY
60 Hz 60HZ
50 Hz 50HZ
TRANSIENT
CAPTURE
Standard (256 samples per cycle) -
Transient module(transient over-voltages as short as 17 µs
are detectable, up to 2 kV amplitude is measurable) TRM
No Inputs / Outputs -
None -
50-288V AC and 40-290V DC
(cannot be combined with Standard voltage input) AUX-
ACDC
TESTING AND CERTIFICATE
Full functional test,
-
calibration at various work loads & detailed test report
Full functional test, calibration at various work loads &
detailed test report plus ISO 17025 and ILAC certified C
calibration certificate C
SATEC Inc.
10 Milltown Court, Union, NJ 07083
Tel: 1-888-OK-SATEC
Local: 908-686-9510
Fax: 908-686-9520 sales@satec-
global.com
w w w.satec-
global.com
BB0151 REV.A2