Professional Documents
Culture Documents
DIGITAL CAMERA
FinePix S1000fd
US/EU/E1/EG/EE/CH-model
SERVICE MANUAL
CAUTION
BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIGNATED AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN PERFORMING REPAIRS. (Refer to page 3 to page 5)
WARNING
THE COMPONENTS IDENTIFIED WITH THE MARK " " ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY. PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST. IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN ELECTRICAL SHOCK.
Ref.No.: ZM00722-101
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
SAFETY CHECK-OUT
After correcting the original problem, perform the following safety check before return the product to the customer.
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splasher and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B + voltage to see it is at the values specied. 6. Make leakage - current measurements to determine that exposed parts are acceptably insulated from the supply circuit before returning the product to the customer.
RISK OF FIREREPLACE FUSE AS MARKED
7.
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH SAME TYPE 2.5 AMPERES 125V FUSE. ATTENTION: AFIN D'ASSURER UNE PROTECTION PERMANENTE CONTRE LES RISQUES D'INCENDIE, REMPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME, TYPE 2.5 AMPERES, 125 VOLTS. WARNING: TO REDUCE THE ELECTRIC SHOCK, BE CAREFUL TO TOUCH THE PARTS.
2.5A 125V
2.5A 125V
8.
WARNING!
HIGH VOLTAGE
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
With the exception of parts and materials expressly excluded from the RoHS directive(*1), all the internal connections and component parts and materials used in this product are lead-free compliant(*2) under the European RoHS directive. *1: Excluded items (list of the main lead-related items) Lead included in glass used in uorescent tubes, electronic components and cathode-ray tubes Lead in high-melting-point solder (i.e. tin-lead solder alloys that contain 85% lead or more) Lead in ceramic electronic parts (piezo-electronic devices) Mercury contained in uorescent tubes is also excluded. *2: Denition of lead-free A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.) <Reference> RoHS: Designated substances (6):
The name of a directive issued by the European Parliament aimed at restricting the use of certain designated hazardous substances included in electrical and electronic equipment. Lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl ether (PBDE)
<Lead-free soldering>
When carrying out repairs, use a designated lead-free solder, bearing in mind the differing work practices for conventional solder (eutectic) and lead-free solder.
When the soldering work practices for eutectic solder and lead-free solder are compared, the main differences are as shown below. In particular, when lead-free solder is used, the solder tends to be less workable than when eutectic solder is used. Accordingly, the soldering techniques used must take that into account. Difference Countermeasure The initial melting point of lead-free solder is high, so you have to get used to it. Move the tip of the soldering iron around to heat the entire connection to the melting temperature and assist wetting. Use the solder (wire) diameter and soldering iron that are best suited to connection being soldered. First apply solder to the area immediately around the through hold and then feed the solder into the hole. Use a suitable wicking wire (with a suitable method and heating) and a suction tool. Either put solder onto the soldering iron tip after completing the work, or turn the iron off frequently. Learn to recognize the appearance of the surface. The solder starts melting later. Poor wetting Solder feed rate is difcult to control. Wetting the insides of through holes is especially difcult. During repairs (or modications) removing solder from inside through holes is difcult. There is serious carbonization of the soldering iron. The surface is not glossy.
1 2 3 4 5 6 7
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Setting temperature during lead-free soldering
Lead-free solder melting temperature The melting point of eutectic (Sn-Pb) solder is 183C, while the melting point of lead-free solder (Sn-Ag-Cu) is 30C higher at 220C.
Soldering iron tip temperature The temperature setting for the soldering iron used should be such that the tip of the soldering iron is at the correct bonding temperature for the connection. This temperature is normally set at around 100C higher than the melting point of the solder. However, the actual temperature should take into account the shape and size of the soldering iron tip, the heat tolerance of the connection and the workability of that temperature. Correct bonding temperature The correct bonding temperature refers not to the temperature of the heat source, but to the bonding temperature that will give the best bond strength.
Soldering iron maintenance Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the ux adhering to the tip of the soldering iron. (1) Always cover the tip of the soldering iron with solder when it is not being used. (2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.
Uniform heating of the board and components To ensure that the lead-free solder wets the entire surface of the pattern and the lands despite its poor wetting characteristics, you must move the tip of the soldering iron over a wide area to raise the temperature of the entire connection.
Soldering iron
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Solder wire (thread)
Use the lead-free solders specied below. Solder type: Sn96.5Ag3Cu0.5 (Displayed symbol: SnAgCu) Wire diameter: 0.6, 0.8 or 1.0 mm Sample:
lead-free
Flux
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
CONTENTS
CONTENTS
1. General ....................................................... 1-1 3. Schematics ................................................. 3-1
1-1. Product specication............................................1-1 1-2. Explanation of Terms ...........................................1-5 1-3. Names of External Components ..........................1-6
Names of internal Components ...........................2-1 Removing the BACK COVER CONST ................2-2 Disassembling the BACK COVER CONST .........2-2 Removing the LCD and TOP COVER CONST ....2-3 Disassembling the TOP COVER CONST ............2-5 2-5-1. Removing the MODE DIAL and other operation buttons ...................................2-5 2-5-2. Removing the EVF and FLASH unit.......2-7 2-6. Removing the MAIN PWB ASSY .........................2-9 2-7. Removing the LENS CONST...............................2-9 2-8. Removing the BATTERY PWB ASSY and main capacitor ...................................................2-10 2-9. Disassembling the FRONT COVER CONST ..... 2-11 2-10. Installation locations for the SEAL and MYLAR .......................................2-12 2-10-1. Attaching the KEY SHEET METAL MYLAR to the KEY SHEET METAL ......................2-12 2-10-2. Attaching the TOP COVER MYLAR to the TOP FPC UNIT ..............................2-12 2-10-3. Attaching the FLASH DETECT WIRE MYLAR to the FLASH DETECT WIRE UNIT ........2-13 2-10-4. Attaching the FLASH SPONGE to the TOP COVER ..................................2-13 2-10-5. Attaching the CAP. MYLAR B to the MAIN FRAME.................................2-13 2-10-6. Attaching the CAP. MYLAR A and BATTERY SEAL to the BATTERY PWB ASSY ...................2-14 2-10-7. Afxing the LCD HOLDER MYLAR to the LCD HOLDER ................................2-14 2-10-8. Attaching the CAP. MYLAR A to the LCD ................................................2-14 2-10-9. Attaching the BATTERY SEAL, LENS FPC SPONGE and TAPE GASKET to the MAIN PWB ASSY...........................2-15 2-10-10. Attaching the DUST PROOF SPONGE to the LENS RING ....................................2-15
3-1. Cautions...............................................................3-1 3-2. Basic Block Names and Functions ......................3-1 3-3. Description of Main Block Functions....................3-2 3-3-1. Technical Overview ................................3-2 3-3-2. Explanation of each block ......................3-2 3-4. Block Diagram .....................................................3-3 3-5. Overall connection Diagram ................................3-4 3-6. Circuit Diagrams ..................................................3-5 3-6-1. BATT BOARD BLOCK ...........................3-5 3-6-2. CCD 3 in 1 BLOCK ................................3-6 3-6-3. CCD FPC BLOCK ..................................3-7 3-6-4. DDR+NAND/SD CARD BLOCK .............3-8 3-6-5. DSP BLOCK ...........................................3-9 3-6-6. KEY FPC BLOCK .................................3-10 3-6-7. LCD EVF USB LED AUDIO IN PORT BLOCK ................................. 3-11 3-6-8. MOTOR BLOCK ...................................3-12 3-6-9. POWER BLOCK ..................................3-13 3-6-10. TOP FPC BLOCK ................................3-14 3-7. Mounted Parts Diagrams ...................................3-15 3-7-1. BATTERY BOARD ASSY .....................3-15 3-7-2. AF LED ASSY ......................................3-17 3-7-3. CCD FPC ASSY ...................................3-17 3-7-4. MAIN BOARD ASSY ............................3-18 3-7-5. FLASH BOARD ASSY .........................3-20 3-7-6. TRIGGER BOARD ASSY.....................3-20 3-7-7. KEY FPC ASSY ...................................3-20 3-7-8. TOP FPC ASSY ...................................3-21
CONTENTS
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
CONTENTS
4. Adjustments ............................................... 4-1 5. Inspection ................................................... 5-1
4-1. Important point before adjustment .......................4-1 4-1-1. The handling of image les in internal memory .....................................4-1 4-1-2. Adjustment when replacing major parts..............................4-2 4-2. Measuring instruments used................................4-2 4-3. Use jig list ............................................................4-2 4-4. Calibration method of pattern box........................4-3 4-5. Preparation of Adjustment Software ....................4-4 4-5-1. Various downloading software decompressions, preservation methods, and notes ...........4-4 4-5-2. Explanation of the "MENU" Adjustment Software ..........4-5 4-6. MAIN PWB Initialize.............................................4-7 4-7. Self test & Lens test .............................................4-9 4-8. End Voltage Adjustment..................................... 4-11 4-9. AF Adjustment ...................................................4-13 4-10. Shutter Adjustment ............................................4-16 4-11. ISO Sensitivity Adjustment.................................4-18 4-12. CCD Defect Correction ......................................4-20 4-13. Color Correction.................................................4-22 4-14. Flash Adjustment ...............................................4-24 4-15. Preparation of FxS1000fd USB ID Writing Software .................4-26 4-15-1. Various downloading software decompressions, preservation methods, and notes .........4-26 4-16. USB_ID Writing ..................................................4-27 4-17. Langeuage Setting.............................................4-34
5-1. Required Measuring Equipment ..........................5-1 5-2. Connection of Measuring Equipment...................5-1 5-3. Inspection and Factory Settings ..........................5-2
6-1. Packing and Accessories .....................................6-1 6-1-1. US-model ...............................................6-1 6-1-2. EU-model ...............................................6-2 6-1-3. E1-model ................................................6-3 6-1-4. EG-model ...............................................6-4 6-1-5. EE-model ...............................................6-5 6-1-6. CH-model ...............................................6-6 6-2. FRONT COVER CONST .....................................6-7 6-3. BATTERY COVER CONST .................................6-8 6-4. MECHANICAL BLOCK ........................................6-9 6-5. TOP COVER CONST ........................................6-10 6-6. Electrical parts ................................................... 6-11
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
1. General
1. General
1-1.
System
Product specication
Digital camera FinePix S1000fd 10.0 million pixels 1/2.3-inch CCD Internal memory (approx. 24 MB)/xD-Picture Card (16/32/64/128/256/512 MB/1 GB/2 GB)/ SD/SDHC Memory Card (FUJIFILM recommendation) Still image: DCF-compliant Compressed: Exif ver.2.2 JPEG, DPOF-compatible *Design rule for Camera File System compliant/DPOF compatible Movie: AVI format, Motion JPEG Audio: WAVE format, Monaural sound
Still image: 3648 2736 pixels/3648 2432 pixels/2592 1944 pixels/2048 1536 pixels 1600 1200 pixels/640 480 pixels ( /%/[/3/2/`)
Lens Focal length Digital zoom Aperture Focal range (from lens surface)
Fujinon 12 optical zoom lens F2.8 (Wide-angle)-F5.0 (Telephoto) f=5.9 mm-70.8 mm (Equivalent to approx. 33 mm-396 mm on a 35 mm camera) Approx. 5.7 (12 optical zoom lens is used together: Max. zoom scale: approx. 68.4) F2.8-F6.4 (Wide-angle) to F5.0-F8.0 (Telephoto) in 1/3 EV increments Manual/ Auto selectable Normal: Wide-angle: approx. 40 cm (1.3 ft.) to infinity (In High-speed shooting mode: approx. 1.5 m (4.9 ft.) to infinity) Telephoto: Macro: approx. 1.5 m (4.9 ft.) to infinity (In High-speed shooting mode: approx. 2.0 m (4.9 ft.) to infinity) Wide-angle: 5 cm to 3.0 m (11.7 in. to 9.9 ft.) Telephoto: 80 cm to 9.9 m (2.6 ft. to 11.5 ft.)
Super macro: Approx. 2 cm to 10 cm (0.4 in. to 3.9 in.) Focal length: fixed to approx. 60 mm (35 mm camera equivalent) Sensitivity Photometry Exposure control Scene position [AUTO]/[AUTO(400)]/[AUTO(800)]/Equivalent to ISO [64]/[100]/[200]/[400]/[800]/[1600]/ [3200] (max. number of recorded pixels:3) (Standard output sensitivity) TTL 256-zones metering Multi, Spot, Average Program AE (When using P mode : Program Shift is enabled)/Shutter priority AE/Aperture priority AE/Manual exposure ([NATURAL LIGHT]), H ([PORTRAIT]), , ([LANDSCAPE]), . ([SPORT]), / ([NIGHT]), ([MUSEUM]), Intelligent Face Detection Exposure compensation Available 2 EV to +2 EV in 1/3 EV-step increments (N, <, M) ([FIREWORKS]), ([PARTY]), ([SUNSET]), ([SNOW]), ([BEACH]), ([FLOWER]), ([TEXT]),
([PICTURE STABILIZATION])
1-1
1. General
System
Shutter speed B, , H, ,, ., , , /: 3 sec. to 1/1000 sec.* : 8 sec. to 1/2 sec.*
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
: 1/45 sec. to 1/2000 sec.* (flash only). N, <: 1/45 sec. to 1/2000 sec.* (8 sec. to 1/2000 sec.* when suppressed flash is set) M, >: 8 sec. to 1/2000 sec.* *depend on Exposure mode Continuous shooting Continuous shooting (TOP 152): Number of recorded frames: up to 15 frames (Max. 7.5 frames/sec.) Continuous shooting (TOP 6[): Number of recorded frames: up to 6 frames (Max. 3.3 frames/sec.) Long period continuous shooting (LONG PERIOD): Number of recorded frames: Depend on memory size. 0.7 sec. interval at depending on quality level. (Max. 1.4 frames/sec.) Continuous shooting (LAST 3): Number of recorded frames: 3 frames just before releasing shutter button (Max. 1.4 frames/sec) Bracketing: (BRACKETING) Number of recorded frames: up to 3 frames (appropriate, over or under setting value) Continuous shooting (TOP 3): Number of recorded frames: up to 3 frames (Max. 1.4 frames/sec.) Auto bracketing Focus 1/3 EV, 2/3 EV, 1 EV Mode: Single AF, Continuous AF AF system: TTL contrast-type, AF-assist illuminator (effective distance: 1.8m) AF frame selection: AF (CENTER), AF (MULTI), AF(AREA) White balance Self-timer Flash type Automatic scene recognition/Preset (Fine, Shade, Fluorescent (Daylight), Fluorescent (Warm White), Fluorescent (Cool White), Incandescent) /Custom Approx. 2 sec./10 sec. Auto flash Effective range: (S: [AUTO]): (Macro): Flash mode approx. 40 cm-8.7 m (1.3 ft.-28.5 ft.) (Wide-angle) approx. 1.5m-4.8m (4.9 ft.-15.7 ft.) (Telephoto) approx. 30 cm-3.0 m (1.0 ft.-9.8 ft.) (Wide-angle) approx. 0.8m-3.0m (2.6 ft.-9.8 ft.) (Telephoto) Red-eye removal set to OFF: Auto, Forced Flash, Suppressed Flash, Slow Synchro Red-eye removal set to ON: Red-eye Reduction Auto, Red-eye Reduction & Forced Flash, Suppressed Flash, Red-eye Reduction & Slow Synchro Viewfinder LCD monitor Movie Photography functions Playback functions Other functions 0.20 inches, approx. 200,000 dots FLCD monitor, (Each dot displays all R, G, and B colors consecutively), Approx. 97% coverage 2.7 inches, Aspect ratio: 4:3; approx. 230,000 dots TFT color LCD monitor, Approx. 97% coverage 640 480 pixels/320 240 pixels (%/$) (30 frames per second with monaural sound) Intelligent face detection, Red eye removal, High-speed shooting, Best framing, Post shot assist window, Frame No. memory, Histograms, Panorama Intelligent face detection, Micro thumbnails playback, Trimming, Slide Show, Multi-frame playback, Sorting by date, Image rotate, Histograms (Highlight warning), Voice memo PictBridge, Exif print, Language ( , , , , English, Franais, Deutsch, Espaol, Italiano, , , Magyar, Polski, Svenska), Time , Portugus, Nederlands, N
1-2
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual Input/Output Terminal
A/V OUT (Audio/Visual output) Digital input/output NTSC/PAL-type (with monaural sound)
1. General
USB 2.0 High-Speed, PTP (Picture Transfer Protocol)/MTP (Media Transfer Protocol)
According to the CIPA (Camera & Imaging Products Association) standard procedure for measuring digital still camera battery consumption (extract): When using alkaline batteries, use the batteries supplied with the camera. You can use NiMH batteries also. The storage media should be xD-Picture Card. Pictures should be taken at a temperature of +23C (+73F), with the LCD monitor turned on, the optical zoom moved from full wide-angle to full telephoto (or vice-versa) and back again to its original position every 30 seconds, the flash used at full power every second shot and the camera turned off and then on again once every 10 shots. Note: Because the number of available shots varies depending on the capacity of alkaline batteries, lithium batteries or the level of charge in Ni-MH batteries, the figures shown here for the number of available shots using batteries are not guaranteed. The number of available shots will also decline at low temperatures. Camera dimensions (W/H/D) Camera mass (weight) Weight for photography Operating Conditions 102.5 mm 73 mm 67.8 mm/4.0 in. 2.9 in. 2.7 in. (not including accessories and attachments) Approx. 325 g/11.5 oz. (not including accessories, batteries and Memory Card) Approx. 420 g/14.8 oz. (including batteries and Memory Card) Temperature: 0C to +40C (+32F to +104F) 85% humidity or less (no condensation)
1-3
1. General
Power Supply and Others
Accessories included Shoulder strap (1) Lens cap (1 set) A/V cable (1) USB cable (1)
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
CD-ROM (Software for FinePix) (1) Owner's Manual (1) Notes and Cautions (1) Optional accessories xD-Picture Card (256MB/512MB/1GB/2GB) AC Power Adapter AC-5VX DC Coupler CP-04 PC Card Adapter DPC-AD * Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 2 MB to 128 MB. CompactFlash Card Adapter DPC-CF ZStandard number of available frames/recording time per xD-Picture Card, SD Memory Card and internal memory The number of available frames and recording time is approximate. The actual number of frames and recording time varies depending on the type of Memory Card or shooting conditions. Also, the number of frames and recording time displayed in the LCD monitor may not decrease regularly. Quality setting Number of recorded pixels Image data size Internal memory (approx. 24 MB) 16 MB 32 MB xD-Picture Card 64 MB 128 MB 256 MB 512 MB 1 GB 2 GB 512 MB 1 GB 2 GB 4 GB 8 GB SD Memory Card F N % [ 3 2 ` % (30 fps) $ (30 fps)
3648 2736 4.9 MB 2.5 MB 5 3 6 13 26 52 104 209 418 101 202 405 811 1627 9 6 12 25 51 103 207 415 830 200 402 804 1611 3233
3648 2432 2592 1944 2048 1536 1600 1200 640 480 640 480 320 240 2.2 MB 11 7 14 29 58 116 233 466 927 225 452 898 1798 3608 1.3 MB 19 12 25 50 101 202 404 809 1599 391 784 1549 3102 6225 789 KB 30 19 39 79 159 319 639 1279 2559 618 1239 2479 4964 9960 631 KB 38 24 49 99 199 399 799 1599 3199 773 1549 3098 6205 12450 134 KB 170 110 221 444 888 1777 3551 7108 12796 3438 6885 12395 24518 47132 29 sec. 19 sec. 38 sec. 1.2 min. 2.5 min. 5.1 min. 10.2 min. 20.5 min. 41.1 min. 9.9 min. 19.9 min. 39.8 min. 53 sec. 34 sec. 1.1 min. 2.3 min. 4.6 min. 9.2 min. 18.4 min. 37.0 min. 74.0 min. 17.9 min. 35.8 min. 71.7 min.
* A movie recording will stop automatically when a movie file becomes approx. 2GB. If you want to continue recording, press the shutter button again. The available recording time is displayed based on approx. 2GB.
1-4
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
1. General
1-2.
Explanation of Terms
Leaving an Ni-MH battery unused in storage for a long period may cause a rise in the level of substances that inhibit current flow inside the battery and result in a dormant battery. A battery in this state is referred to as deactivated. Because current flow is inhibited in a deactivated Ni-MH battery, the batterys original level of performance cannot be achieved.
Deactivated batteries
EV
A number denotes Exposure Value. The EV is determined by the brightness of the subject and sensitivity (speed) of the film or CCD. The number is larger for bright subjects and smaller for dark subjects. As the brightness of the subject changes, a digital camera maintains the amount of light hitting the CCD at a constant level by adjusting the aperture and shutter speed. When the amount of light striking the CCD doubles, the EV increases by 1. Likewise, when the light is halved, the EV decreases by 1.
The frame rate refers to the number of images (frames) that are photographed or played back per second. For example, when 10 frames are continuously photographed in a 1-second interval, the frame rate is expressed as 10 fps. For reference, TV images are displayed at 30 fps (NTSC).
JPEG
Joint Photographic Experts Group A file format used for compressing and saving color images. The higher the compression rate, the greater the loss of quality in the decompressed (restored) image.
Memory effect
If an Ni-MH battery is repeatedly charged without first being fully discharged, its performance may drop below its original level. This is referred to as the memory effect.
Motion JPEG
A type of AVI (Audio Video Interleave) file format that handles images and sound as a single file. Images in the file are recorded in JPEG format. Motion JPEG can be played back by QuickTime 3.0 or later.
Smear
A phenomenon specific to CCDs whereby white streaks appear on the image when there is a very strong light source, such as the sun or reflected sunlight, in the photography screen.
WAVE
A standard format used on Windows systems for saving audio data. WAVE files have the .WAV file extension and the data can be saved in either compressed or uncompressed format. Uncompressed recording is used on this camera. WAVE files can be played back on a personal computer using the following software: Windows: MediaPlayer Macintosh: QuickTime Player * QuickTime 3.0 or later
White Balance
Whatever the kind of the light, the human eye adapts to it so that a white object still looks white. On the other hand, devices such as digital cameras see a white subject as white by first adjusting the color balance to suit the color of the ambient light around the subject. This adjustment is called matching the white balance. Exif Print Format is a newly revised digital camera file format that contains a variety of shooting information for optimal printing.
1-5
1. General
1-3.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Zoom lever (Multi-frame playback) Shutter button Intelligent Face Detection / b Red-eye removal button f Continuous button Strap mount Strap mount ON/OFF switch Indicator lamp Mode dial
Microphone
Speaker
1-6
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
1. General
EVF/LCD (monitor selector) button w (Playback) button p (Photo mode) button nopq (4-direction) button Terminal cover
Tripod mount
1-7
1. General
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
1-8
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2. Disassembly
2. Disassembly
2-1. Names of internal Components
MAIN FRAME
LENS CONST
SPEAKER MIC
2-1
2. Disassembly
2-2.
(1) Remove the screw (M1.7 x L4.5). (2) Remove the 2 screws (M1.7 x L3.5). (3) Remove the screw (M1.7 x L2.5). (4) Remove the screw (M1.7 x L3.0). (5) Remove the 2 special screws (M1.7 x L3.5). (6) Open the USB COVER.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
(7) Remove the BACK COVER CONST in the direction of the arrow, taking care with the USB connector. * Raise the BACK COVER CONST slowly because the KEY FPC is connected to the MAIN PWB ASSY. (8) Unlock the connector and remove the KEY FPC. [Assembly] Assemble by performing the disassembly procedure in reverse.
3
5
2
2-3.
(1) Peel off the KEY SHEET METAL MYLAR. (2) Remove the 7 screws (M1.4 x L2). (3) Remove the KEY FPC UNIT in the direction of the arrow. (4) Remove the OK BUTTON in the direction of the arrow. (5) Remove the 4 WAY BUTTON, 2 BUTTON and 3 BUTTON in the direction of the arrows. (6) Remove the USB COVER. [Assembly] Assemble by performing the disassembly procedure in reverse.
4
2-2
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2. Disassembly
2
3
2-4.
(1) Remove the screw (M1.7 x L3.0). (2) Remove the STRAP LEFT in the direction of the arrow. (3) Remove the 2 screws (M1.4 x L3). (4) Pop up the FLASH unit and remove the 2 screws (M1.4 x L3). (5) Unlock the connector and remove the FPC.
3 4
(6) Raise the TOP COVER CONST in the direction of the arrow, taking care with the 2 HOOKS. [Main capacitor discharge points] * Take care not to touch the main capacitor terminals before discharging the capacitor. (7) Peel off the CAP. MYLAR A. (8) Discharge the main capacitor.
6
HOOK
2-3
2. Disassembly
(9) Raise the LCD in the direction of the arrow. (10) Remove the 2 screws (M1.7 x L3.5). (11) Remove the screw (M1.4 x L3.0). (12) Remove the LCD HOLDER in the direction of the arrow.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
10
11
12
(13) Unlock the connector and remove the LCD FPC. (14) Unlock the connector and remove the EVF FPC. (15) Disconnect the connector. (16) Disconnect the connector.
16
14
15
13
2-4
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2. Disassembly
2-5.
2-5-1.
(1) Peel off the TOP COVER MYLAR. (2) Remove the 7 screws (M1.4 x L2). (3) Remove the TOP FPC UNIT. (4) Remove the MODE DIAL SWITCH COVER.
2
(5) Remove the screw (M1.4 x L2) and then remove the POWER KNOB. (6) Remove the screw (M1.4 x L3) and then remove the MODE DIAL STOPPER, MODE DIAL SPRING and MODE DIAL. (7) Remove the 2 screws (M1.4 x L3) and then remove the WT SLIDER, WT SPRING, WT BUTTON, SHUTTER SPRING and SHUTTER BUTTON. (8) Remove the TOP COVER BUTTON. (9) Remove the screw (M1.4 x L2). (10) Remove the STATUS LED. [Assembly] Assemble by performing the disassembly procedure in reverse.
7 5
6 9 10
2-5
2. Disassembly
[Notes on Assembly] Precautions when installing the TOP FPC UNIT (1) Note the installation locations of the MODE DIAL STOPPER and MODE DIAL SWITCH COVER as shown in the gure.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
(2) Set POWER KNOB at the position of gure, and install TOP FPC UNIT.
2-6
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2-5-2. Removing the EVF and FLASH unit
1 5 2 6
2. Disassembly
(1) Remove the screw (M1.4 x L3). (2) Remove the FLASH BOARD. (3) Remove the screw (M1.4 x L2). (4) Remove the FLASH LOCK PUSHER and FLASH LOCK SPRING. (5) Remove the screw (M2.0 x L5.0). (6) Remove the FLASH BUTTON. (7) Remove the 3 screws (M1.4 x L2). (8) Remove the FLASH LOCK PLATE.
4 8
(9) Remove the FLASH LOCK in the direction of the arrow. (10) Remove the 2 screws (M1.4 x L2). (11) Remove the EYE RING in the direction of the arrow. (12) Remove the 2 screws (M1.4 x L3). (13) Remove the EVF in the direction of the arrow.
10
12 11 13
14
2-7
2. Disassembly
(15) Close the FLASH unit and remove the FLASH TOP COVER, taking care with the 2 hooks.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
15
Hook
(16) Pull out the FLASH HINGE in the direction of the arrow. (17) While pulling out the FLASH HINGE in the direction of the arrow, remove the FLASH SPRING. * Take care, since pulling out the FLASH HINGE may cause the FLASH SPRING to y out. (18) Remove the screw (M1.4 x L3). (19) Remove the FLASH FIX. (20) Remove the solder in 3 locations and remove the FLASH UNIT. [Assembly] Assemble by performing the disassembly procedure in reverse. [Notes on Assembly] After completing the soldering at point A, apply adhesive so that it covers the soldered area. Bond : ZS00131-100 (No.8008)
17 20 18 19
16
2-8
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2. Disassembly
7
2-6.
(1) Remove the BATTERY COVER CONST. (2) Unlock the connector and remove the CCD FPC. (3) Pull off the LENS FPC SPONGE as shown in the gure. (4) Pull off the BATTERY SEAL as shown in the gure. (5) Unlock the connector and remove the LENS FPC. (6) Remove the solder in 4 locations. (7) Remove the solder in 10 locations. (8) Remove the TEAP GASKET. (9) Remove the 2 screws (M1.7 x L3.5). (10) Remove the MAIN PWB ASSY in the direction of the arrow while taking care with point A.
4
5
2
A
6
10
9
2-7.
(1) Remove the 3 screws (M1.7 x L4.5). (2) Remove the LENS CONST in the direction of the arrow.
2-9
2. Disassembly
2-8.
(1) Remove the 2 screws (M1.7 x L4.5). (2) Remove the BATTERY SEAL. (3) Remove the screw (M1.4 x L3). (4) Remove the solder in 8 locations. (5) Remove the BATTERY PWB ASSY.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
(6) Remove the 3 screws (M1.4 x L3). (7) Remove the AF LED PWB ASSY and LED SILICONE. (8) Peel off the CAP. MYLAR B. (9) Remove the main capacitor. [Notes on Assembly] Coat the screws removed in step (6) with a screw locking agent. SCREW LOCK : ZS00136-100
7 9
2-10
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2. Disassembly
4
2-9.
(1) Remove the screw (M1.7 x L4.5). (2) Remove the STRAP RIGHT. (3) Remove the 2 screws (M1.7 x L3.5). (4) Remove the 3 screws (M1.7 x L4.5). (5) Remove the screw (M1.7 x L2.5). (6) Remove the MAIN FRAME. (7) Remove the screw (M1.7 x L3.5). (8) Remove the TRIPOD. (9) Remove the 2 screws (M1.7 x L2.0). (10) Remove the LENS RING.
9
9
6
2
8
7
10
[Notes on Assembly] Run the wire harnesses in the layout shown in the gure.
(11) Remove the 4 screws (M1.7 x L3.5). (12) Remove the HAND GRIP. (13) Remove the 4 screws (M1.4 x L2). (14) Remove the BATTERY SPRING.
11
14
13
12
2-11
2. Disassembly
2-10.
2-10-1.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Attaching the KEY SHEET METAL MYLAR to the KEY SHEET METAL
2-10-2.
2-12
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2-10-3.
2. Disassembly
Attaching the FLASH DETECT WIRE MYLAR to the FLASH DETECT WIRE UNIT
2-10-4.
2-10-5.
2-13
2. Disassembly
2-10-6.
(1) Afx the CAP. MYLAR A as shown in the gure. (2) Afx the BATTERY SEAL as shown in the gure.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Attaching the CAP. MYLAR A and BATTERY SEAL to the BATTERY PWB ASSY
1
2-10-7.
2-10-8.
2-14
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2-10-9.
2. Disassembly
3
Attaching the BATTERY SEAL, LENS FPC SPONGE and TAPE GASKET to the MAIN PWB ASSY
(1) Afx the BATTERY SEAL as shown in the gure. (2) Afx the LENS FPC SPONGE as shown in the gure. (3) Afx the 2 TAPE GASKETS as shown in the gure.
lip
2-15
2. Disassembly
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
2-16
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
3. Schematics
3-1.
<Cautions when replacing parts>
Do not reuse removed parts. Always use new parts. Note that the negative side of tantalum condensers is readily damaged by heat. Except for chemical condensers and tantalum condensers, voltage is not displayed on condensers with a voltage resistance of 50V or less. Resistors not marked are 1/16W chip resistors. K = 1000, M = 1000K B characteristics of variable resistors and semi-xed resistors are not displayed.
Cautions
3-2.
CCD
MAIN PWB
FLASH LCD UNIT TOP FPC ASSY BATT BOARD ASSY KEY FPC
FLASH BLOCK
3-1
3. Schematics
3-3.
3-3-1. Technical Overview
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Equipped with a 1/2.3-inch square-pixel interline CCD (total pixels 10.17 million pixels). Use memory card [xD/SD-picture card]. Optical system featuring a new single-step retracting 12x zoom lens design Features a new IC, which can do CCD processing (FLASH, AFE, A/D 3-int-1) AD19000, OS processing, Functions control, Power control function (BD9739KN), TV enlarged output function (ZR36483BGCF). Flash block module.
3-3-2.
CCD block / CAM block The analog signals output from the CCD (1/2.3-inch square-pixel primary-color interline type (total pixels: 10.17 million (ICX675EQP) ) undergo false color correction, adaptive interpolation, amplication (AGC) and signal mixing in the "DI9000 (U502)" CCD signal processing IC. They are then converted (A/D) to 12-bit digital signals and sent to the DSP system. The "DI9000 (U502)" CCD signal processing IC also incorporates the V driver and H driver that drive the CCD. Motor block The DSP (ER36483BGCF), which receives the command do signal from each operation system, control the motor drive IC "AAA11883 (U601)", and control the motor of AF/Shutter/Zoom/Iris. Signal Process block Input data from CCD The 12bit digital image data sent from the CCD/CAM block is sent to DSP of camera (inside the DRAM (16 M byte)), which equals to 1 frame (2048 pix x 1536 pix) is temporarily stored. At the same time, the image data sent to DSP is calculated in [Auto calculation block], to obtain the correct AE/AWB/AF. The data is sent to and temporarily stored in SDRAM (U100). Recording onto an xD-Picture card The image data held in SDRAM U100 (CT48568126A-G4) is sent one DSP line at a time to the internal [signal processing unit], which unpacks the data. This consists of "32-bit -> 10-bit conversion", "pre-processing such as digital clamping, gamma correction and conversion of the R, G, and B channels from 10 bits to 8 bits", followed by "YC processing of each of the 8-bit digital RGB signals where Y:Cb:Cr = 4:2:2". The Y, Cb and Cr 8-bit image data is then sent to the internal buffer -- SDRAM. The image data of Y/Cb/Cr each 8bit is sent to the inside buffer SDRAM. [Inside bufferSDRAM] change each Y/Cb/ Cr signal of 8bit into the easily changed DCT pattern. By the DSP [JPEG calculation compression] -> [Media controller] ->SDRAM, and last stored in the xD-Picture card. Playing back image data from an xD-Picture card The compressed 8bit image data from the xD-Picture card is sent to it SDRAM -> DSP MEDIA control section -> [DMAUNIT] -> [Inside DRAM (16Mbyte)] -> [Media controller] -> [JPEG calculation block] -> [Signal process block]. The imaging system adjustment data is stored by Flash ROM (U100). LCD / EVF unit The digital signal from DSP (U200) system is sent to the drive IC of LCD unit, through the process block of LCD FPC to undergo LCD drive and LCD panel adjustment control. The signals processed by the DSP (U200) are also sent to the EVF. DCDC BLOCK A power-supply circuit consisting primarily of a DCIC (U400) generates the power supplies shown below and supplies the power to each block. 3V3M [DSP (U200), DI9000 (U502), FLASH ROM (U100), SDRAM (U100)], FLASH IC (U200), MOTOR Drv (U601), xD Pictuer Card, TFT, Audio process IC (U200), Video process IC (U200), CCD IC (U502) 1V8M DSP (U200) LEDA Color TFT LEN_3V3 LENS DRIVER IC (U601) CCD13V CCD (U502) CCD7.5VN CCD (U502)
3-2
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
Battry Board
3-4.
Block Diagram
Flash detect
Main Board
12 MHz
USB PORT
ADDI9000(3 in 1) U502
38 MHz
Key FPC
CN301
Power system U400 Zoran coach 10S
Top FPC
CN302
Y200 RTC
Lens unit
32.768 KHz
3-3
3. Schematics
3-5. Overall connection Diagram
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
CCD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
SUB VL VOG LV VGND V1A V1B V2 V3A V3B NC V3C V4 V5A V5B V5C V6S1 V6S2 VST2 VST1 VOUT VDD NC RG NC AGND AGND HGND CSUB SUB CONT NC NC NC NC LH1 H1 H2 NC VHLD1 VHLD2
CCD FPC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
GND GND CCDV13P CCDV13P CCDV7N5 CCDV7N5 GND GND V13 V14 V12 V11 V4 V6B V6A V8 V3 V5B V5A V7 V2 V1 V17 V10 V16 V15 GND SUB GND H2 H2 GND H2 H2 GND HL HL GND GND SUB CONT BUFF CTL GND GND RG RG GND GND CCD IN CCD IN GND GND J500
DCVIN STATUS GLED VDDPWR AFLED CTL STATUS RLED 3V3M F CHARGE F READY F TRIGGER A GND
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
DCVIN STATUS GLED VDDPWR AFLED CTL STATUS RLED 3V3M F CHARGE F READY F TRIGGER A GND
AFLED+ AFLED-
1 2
1 2
AFLED+ AFLED-
AF LED/B
BAT/B
TRIGGER+ STBSTB+ GND 1 2 3 4 1 TRIGGER+ 2 STB3 STB+ 4 GND
TRIGGER/B
GND GND 3V3M 3V3M VDDPWR PWRON2 KEY AD1 KEY AD1 GND GND
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
GND GND 3V3M 3V3M VDDPWR PWRON2 KEY AD1 KEY AD1 GND GND
KEY_FPC
CON301 GND 3V3M 3V3M VDDPWR GND AFLED CTL MODEDIALSW KEY AD2 PWR SW ON GND 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 GND 3V3M 3V3M VDDPWR GND AFLED CTL TOP_FPC MODEDIALSW KEY AD2 PWR SW ON GND CON302
LENS
FPC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
A GND
ZPR ZPRSW IRIS1 IRIS2 IRIS3 IRIS4 SHUTTER SHUTTER SHUTTER SHUTTER MGND
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
CONNECTOR
USB/AV
J300
01 01 02 02
ZPI ZPISW ZOOM DC+ ZOOM DC+ ZOOM DC ZOOM DC FOCUS STM A FOCUS STM B FOCUS STM A FOCUS STM B 3V3M LENS TEMP FM PI FPISW CON600 VCOM CS SDA SCL HSYNC VSYNC DCLK D7 D6 D5 D4 D3 D2 D1 D0 GND VDD DVDD V1 V2 V3 V4 VDD2 V5 V6 VDD3 VDD5 V7 V8 VGH VGL AGND FRP COMDC VCAC DRV VLED FB COM1 CON306 EVF 5V A GND EVF CS SCLK SDATA LCD D7 LCD D6 LCD D5 LCD D4 EVF 5V LCD D3 LCD D2 LCD D1 LCD D0 LCD HSYNC LCD VSYNC LCD HSYNC EVF CLK EVF RESET A GND EVF C2V5 CON305
MAIN BOARD
1 2 3
1 2 3
FLASH DETECT/B
CON304
LCD
FPC
GND XD CD XD RB XD RE XD CE XD CLE XD ALE XD WE XD WP GND XD D0 XD D1 XD D2 XD D3 XD D4 XD D5 XD D6 XD D7 VCC VCC GND SD DAT2 SD CD/DAT3 SD CMD VSS VDD SD CLK VSS SD DAT0 SD DAT1 SD CD SD CD/WP WP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
GND XD CD XD RB XD RE XD CE XD CLE XD ALE XD WE XD WP GND XD D0 XD D1 XD D2 XD D3 XD D4 XD D5 XD D6 XD D7 VCC VCC GND SD DAT2 SD CD/DAT3 SD CMD VSS VDD SD CLK VSS SD DAT0 SD DAT1 SD CD SD CD/WP WP
SD_CARD XD_CARD
J100
EVF
FPC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
MIC
(PAD313)
MIC N (PAD314)
MIC
SPK
3-4
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
3-6.
3 2
7 6
3-6-1.
4
Circuit Diagrams
BATT BOARD BLOCK
DCVIN
1
1
CI DVN D VI N C
CN 0 1 GD N
CN 2 CN 1 1
CN 5 CN 2 1 3V M 3 3V M 3
R20
Q1 AO8803
DCVIN
F1 2.5A(SMD 0603)
+ C1 47uF/16V
VDDPWR_1
BATP
1
8
1
1
R2 150
1
U1
1M
R3
VCC
VDDPWR_1
VDDP WR VDDP WR
NC
NC
NC
1
1
1
G F_TRI G ER
AF_LED
BATP8
BATP6
BATP7
F_CH RG A E
F_CH F_CHARGE
R19 0R G709
R4 30k
F_REA Y D
F_RE F_READY
C2 0.1uF
HYST
5 4 3
470K
1
Q7 2N7002E
BATP
VDDPWR_1
1 2 3
C8 1uF/ 6. 3V
CN11 1 P
CN13 1 BATP+
BATP
C3 68pF/50V
CN 4 1
1
1 CN12 N
GD N
(MMBT318S)
1 D CH D 004SPT B3
2
DCVIN
3V3M
3V M 3
R5 10K
F_REA Y D
C6 0. 1uF/ 10V
C4 1uF/16V
DVN CI
2 T1
C5
STB+
J1
1 2 3 4
CON_4PIN
0. 1uF/ 10V
T- 18- 389
STB-
R10
R25 2M 1% /
FBVD
/ 35. 7K 1%
BODYGND
DCVIN
3V3M
DVN CI
FBVD
R21 30R
R1 0R
3V3M
LED +
1
1 2 3 4
R26 500K/ 1%
R14
RT9594- V FN 6 Q 1
10R
R11 / 1K 1%
TRI G ER+ G N GD
E E E G
C C C C
DRV U OT
F_REA Y D
8 7 6 5
A E F_CH RG F_TRI G ER G
1 2 3 4 5 6 7 8
U 2
VBAT CS VDOUT FBVD CHARGE DRVIN VDRV DRVOUT
R8 / 150K/ 1% 200V
GND GND SW SW VDD FB STAT GND 16 15 14 13 12 11 10 9
17
C9
K
D2 SM4004GSPT
R9 100K
3V M 3
C10 0. 033uF/ 500V
Q 4 RJ P4002A S N
C7 330PF
R6 150K 1% 200V / /
R7 1M 0603 /
+1 190uF/ 330v_P
-1 190uF/ 330v_N
R15
K
3V3M
R16
N GD
D3 KA
50R
A
ROT DVU
1N448HWT-7
R18 75R
R17 200R
LED 1
10K
N GD
2 Q2
1 AF_LED
STATUS_GLED 1
Q6
2 4
2 3
CHDTC143EEPT
D4 LTST-C195KGJRKT
Q5
STATUS_RLED
CHDTC143EEPT
CHDTC143EEPT
3-5
3. Schematics
3-6-2. CCD 3 in 1 BLOCK
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
J500 1
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
CCD_IN
ROTATION=45
A4 CCD_IN
C500 0.1UF/16V /X7R/0402 TP515 TP500 TP501 1SPCLK 1SPDATA 1AFEVAL C1 SCK C2 SDI B1 SL
8P4R/0402 RN501 33R/5% 8P4R/0402 PCLK_IN VD 1 HD 1 H1_IN H2_IN H1_IN H2_IN HL 1 RG_IN TP504 TP505
1 3 5 7
2 4 6 8
A2 REFT A1 REFB
Y500 38MHZ/32X25
2 3 4
TP502
1TGVAL
D1 RSTB/SYNC
D7 D8 D9 E7 E8 E9 F7 F8 F9 G9 G8 G7 H8 C3 D3 A9 A8 B9 B8 B7 B6
1 5 3 7 3 1 5 7
2 6 4 8 4 2 6 8
CCD0 CCD1 CCD2 CCD3 CCD4 CCD5 CCD6 CCD7 CCD8 CCD9 CCD10 CCD11
8P4R/0402
RN502 33R/5%
RN500 33R/5%
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
J1 J8
H D A7 VD
RG D A6 VD
J9
A D A5 VD D TCV D A3
D V D C9 RD
V G1 L
D D F1 VD
VL L
H V1 V2 H
HL
SUB_CONT RG CCD_IN
H1
FH23-51S-0.3SHW
LC501 0R/5%/0603 H2
TP506
20071120
2
R518 470R/5%/0402 1
SUBCK H7
1 C520 2 1UF/25V X5R/0603
D500
20071120
V1 V2 V3 V4 V5A V5B V6A V6B V7 V8 V9 V10 V11 V12 V13 V14 V15 V16 V17
J2 J3 G3 F3 G4 H3 J4 G5 H4 J5 G6 H5 J6 H6 J7 E3 H2 G2 F2
LC502 0R/5%/0603
1N4448HWT-7-F SDO-523
U502
ADDI9000
V1 V2 V3 V4 V5A V5B V6A V6B V7 V8 V9 V10 1 V11 V12 V13 V14 V15 V16 V17
RG_IN
CCDV13P
SUB
ROTATION=225
3V3M
1 2 1 2
DRVDD 1 1
TP510
F_TRIGGER1 BUFF_CTL 1 1
H1 VM H9 VMM
VL 1 1
1
C7 H SS V E2 D SS V
HVDD_SW 1
AO3418
3
Q503
ROTATION=45
1 2 3
IN GND CE
OUT 6 NC 5 4 SS
1
AVDD 1 1 1
0805
R519 100R/5%
1
U500 LD6911_GU30
3V3M
1
1 2 3
IN GND CE
OUT 6 NC 5 4 SS
1
R507 0R/5%/0603
HVDD 1 1 1
U501 LD6911_GU30
3V3M
R516 10K/5%/0402
3-6
1 2
2 2
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
3-6-3.
CCDV13P
CCDV7N5
CCDV13P
C102 0.01uF/25V/0402
C103 0.01uF/25V/0402
U 100
V _1 1 V _1 2 V _1 7 5 _ VA1 5 V B_1 V _1 3 8 V _1 6 _ VA1 V B_1 6 4 V _1 V 1_1 1 1 V 2_1 1 V 3_1 V 4_1 1 V 5_1 1 1 V 6_1 V 7_1 1 1 V 0_1
6 7 8 9 10 12 13 14 15 16 17 18 20 19 39 40 4 3
V1A V1B V2 V3A V3B V3C V4 V5A V5B V5C V6S1 V6S2 VST1 VST2 VHLD1 VHLD2 LV VOG
VDD
VL
22
C104
ICX675EQP
U 101
ISF0
ISF1
VCC
IDRV0
VO
21
10
IN
CXA3741
IDRV1
0.01uF/25V/0402
U100
8 12 13
C105 0.1uF/25V/0603 29
NC NC NC
U101
OUT
14
1 16
CCD_IN
SFCNT DRVCNT
1 3 CCD 13P V CCD 7N 5 V 5 7 9 V 3_1 1 V 2_1 11 1 13 V _1 4 15 VA1 6 _ 17 V _1 3 19 VA1 5 _ 21 V _1 2 23 V 7_1 1 V 6_1 25 1 27 29 31 H 2 33 H 1 35 37 H L 39 41 BU F_CTL_1 F 43 45 RG 47 CCD I N 49 _ 51
J500
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
2 4 CCD 13P V 6 CCD 7N V 5 8 10 V 4_1 1 12 1 V 1_1 14 6 V B_1 16 V _1 8 18 V B_1 5 20 V _1 7 22 V _1 1 24 1 V 0_1 26 V 5_1 1 28 SU B 30 H 2 32 34 H 1 36 H L 38 40 SU _CO T B N 42 44 RG 46 48 CCD I N _ 50
RG SUB
C106 0.1uF/25V/0603
HL H1 H2
35 36 37
24 1
LH1 H1 H2
RG SUB
SUB_CONT
NC NC NC NC NC NC NC NC
30
11 23 25 31 32 33 34 38
R104 1M
28 26 27 5
C107 2200pF/50/0402
SUB CONT
4 9 11 15
Csub
CCD Connect
BUFF CTL
3-7
3. Schematics
3-6-4. DDR+NAND/SD CARD BLOCK
PCBCLASS=PWR 0R/5%/0402 1 DDR1V8
R116
2 1 1 1 1 1 1
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
20071120
R121 R122 R123 R124 33R/5% 33R/5% 33R/5% 33R/5%
A 2 E2 J 10 M0 1 R2 A0 1 C2 C4 C8 C10 E10 G 2 G 4 G 8 G0 1 J2
D 2_V D R D D 2_V D R D1 D 2_V D R D2 D 2_V D R D3 D 2_V D R D4 D 2_V D R DQ R DQ D 2_V D 1 D 2_V D 2 R DQ D 2_V D 3 R DQ D 2_V D 4 R DQ D 2_V D 5 R DQ D 2_V D 6 R DQ D 2_V D 7 R DQ D 2_V D 8 R DQ D 2_V D 9 R DQ D 2_V D R DL
C N 13 C N C N1 N2 C N3 C C N4 C N5 N6 C N7 C N 14 C N 19 C C N8 N9 C N 10 C N 11 C
DDR_BA1 DDR_BA0 DDRA12 DDRA11 DDRA10 DDRA9 DDRA8 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 DDR_CLKN DDR_CLKP DDR_CKEN DDR_CS DDR_WE DDR_RAS DDR_CAS DDR_LDM DDR_UDM DDR_UDQS_N DDR_UDQS DDR_LDQS_N DDR_LDQS DDR_VREF
L4 L3 R3 P8 M3 P4 P9 P3 N8 N4 N9 N3 M8 M4 M9 K9 J9 K3 L9 K4 K8 L8 F4 B4 A9 B8 E9 F8 J3
DR2_BA01 DR2_BA00 DR2_ADR12 DR2_ADR11 DR2_ADR10 DR2_ADR09 DR2_ADR08 DR2_ADR07 DR2_ADR06 DR2_ADR05 DR2_ADR04 DR2_ADR03 DR2_ADR02 DR2_ADR01 DR2_ADR00
DR2_CLK DR2_CLK
DR2_DQ15 DR2_DQ14 DR2_DQ13 DR2_DQ12 DR2_DQ11 DR2_DQ10 DR2_DQ09 DR2_DQ08 DR2_DQ07 DR2_DQ06 DR2_DQ05 DR2_DQ04 DR2_DQ03 DR2_DQ02 DR2_DQ01 DR2_DQ00 DR2_ODT
R134 R135 R136 R137 R109 10K/1% 0402 R110 10K/1% 0402
DDR1V8
U100 CT48568126A-G4
NAF_DQ07 NAF_DQ06 NAF_DQ05 NAF_DQ04 NAF_DQ03 NAF_DQ02 NAF_DQ01 NAF_DQ00 NAF_PRE NAF_CLE NAF_CE NAF_ALE NAF_RE NAF_WE NAF_RYBY NAF_WP N F_V S A S N F_V S1 A S N F_V C1 A C N F_V C A C
DR2_CKE DR2_CS DR2_WE DR2_RAS DR2_CAS DR2_DQM00 DR2_DQM01 DR2_DQS01 DR2_DQS01 DR2_DQS00 DR2_DQS00 DR2_VREF
FD7 FD6 FD5 FD4 FD3 FD2 FD1 FD0 NAF_PRE NF_CLE NF_CE NF_ALE NF_RE NF_WE NF_RB NF_WPTP101
1
20071203
3V3M
R734
Q101 NC-AO3419
SOT-23
D 2_V S R S D 2_V S1 R S D 2_V S2 R S D 2_V S3 R S D 2_V S4 R S D 2_V SQ R S D 2_V SQ R S 1 D 2_V SQ R S 2 D 2_V SQ R S 3 D 2_V SQ R S 4 D 2_V SQ R S 5 D 2_V SQ R S 6 D 2_V SQ R S 7 D 2_V SQ R S 8 D 2_V SQ R S 9 D 2_V SL R S
N 18 C N 17 C N 16 C N 20 C N 15 C N 12 C
R102
R103
R101
R104
R100
FRDYBSY2 1
XD_RE
A 4 E4 J4 N 2 P10 A 8 B3 B9 D 3 D 9 E8 F3 F9 H 3 H 9 J8 R10 R9 R8 N0 1 R4 P2 E1 K 1
1 K1 1
0R/5% /0402
D1 1
NF_3.3V
1
3V3M
XD_PWR_ON 1
XD_WP
FD0 FD1 FD2 FD3 FD4 FD5 FD6 FD7
6 2 3 4 5
C101 2
/X7R/0402 1 100PF/50V
Q100 NC-CHDTA143EEPT
SC-75
3V3M
20071203
3V3M
RN101 33K/5% 8P4R/0402
2 4 6 8 1 3 5 7
1 4
2 3
SD_D2 SD_D3 SD_D0 SD_D1 33PF/50V C120 2 33PF/50V C121 2 33PF/50V C122 2 33PF/50V C123
2 1 1
10 9 8 7 1
SD_D2 SD_D3
R105 R106
5 VDD
VOUT1 SUB 2
NF_WP1
NF_WP
SW100 SPVN110101
SD_D0 SD_D1
R107 R108
4 GND
NC 3
20071120
BD4830FVE
3V3M
2 4 6 8
1 3 5 7
3-8
2 1
PCBCLASS=PWR
1
DDR_VREF
R114 10K/1%/0402
XD_VCC
1 2 1 2
FRS011-2200-0 J100
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
GND XD_CD XD_RB XD_RE XD_CE XD_CLE XD_ALE XD_WE XD_WP GND1 XD_D0 XD_D1 XD_D2 XD_D3 XD_D4 XD_D5 XD_D6 XD_D7 VCC VCC1 GND3 SD_DAT2 SD_CD/DAT3 SD_CMD VSS VDD SD_CLK VSS1 SD_DAT0 SD_DAT1 SD_CD SD_CD/WP WP
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
3-6-5. DSP BLOCK
20071120
2
3V3M
1
1 1
1 3 5 7
1 3 5 7
/0603 10R/5%
2
1 RN 01 5 2 3 5% 8P4R/ 0402 / 1 7
1UF/10V
X5R/0402
2
10R/
NC-0R/5%
/0402
R269 FI N RQ T FD I N 1 T FSD O LK I C
FA 9 1 FA 8 1 FA 7 1 FA 6 1
3V3M
FRESCE2
33K/5% /0402
2
Y 2 FRD BSY
FA 3 1 FA 2 1
FA 0 1 FA 9 FA 8
TP220 TP249
C226
5
TP241
TP243
6 4 8 2
6 4 2 8
TP216
6 4 8 2 6 4 2 8
TP222 TP223
/0402
D D T4 VA D D T3 VA D D T2 VA VA D D T1 D D T0 VA
FA 3 2 2 FA 2 FA 1 2 FA 0 2
SD CM _ D SD D _ 3 SD D _ 2 SD D _ 0 SD D _ 1
X _CD D SD CD N _ _
N _CLE F N _A E F L
SD CLK _
E15 F18 D8 1 D9 1 B15 E18 C16 H7 1 A5 1 G5 1 E19 A9 1 C14 B19 B14 C19 A4 1 F15 C15
R18 T19 N2 1 P15 E14 F19 E12 J 17 F12 G9 1 F14 G8 1 J 15 H8 1 H4 1 K7 1 G4 1 L18 H5 1 K5 1 F13 G3 1 H9 1 J 18
FA 5 1 FA 4 1
20071225
N _W F P
RX B17 D TX E8 D
D CN L9 V T D CN L8 V T D CN L7 V T D CN L6 V T D CN L5 V T D CN L4 V T D CN L3 V T D CN L2 V T D CN L1 V T D CN L0 V T D CLK V VA D D T7 VA D D T6 D D T5 VA D D T4 VA D D T3 VA D D T2 VA D D T1 VA D D T0 VA
V D CU DF V D CU DF 1 FI N RQ T 1I N # D T D O LK S I C D LK S C TA S1# A C TA S0# A C E2# CC FCFCE1# SCLK M D# C2 D# C1 FRD BSY # Y 2 D BS # R 1 E# O R# W FEX CE1# T FRESCE2# ESCE1# R 7 D 6 D 5 D 4 D 3 D 2 D 1 D 0 D
23 A 22 A 21 A 20 A 19 A 18 A 17 A 16 A 15 A 14 A 13 A 12 A 11 A 10 A 9 A 8 A 7 A 6 A 5 A 4 A 3 A 2 A 1 A 0 A
K3 1 M3 1 N8 1 T18 P19 N3 1 J 19 L15 M8 1 K9 1 M9 1 K4 1 L17 L13 P14 P18 R19 N4 1 N9 1 P13 L14 N5 1 J 14 L19 M4 1 M7 1 K8 1 M5 1
N _CE F
PWR0N2
R273
/0402
FA 2
SFDAT0 SFDAT1 SFDAT2 SFDAT3 SFCMD_BS SFSCLK VSUB3 M4C SD_WP EVF_CS
3V3M
B13 B1 TP255 A2 A3 0R/5% /0402 F11 0R/5% /0402 A4 LCDPWR_CTL E11 MOTPWR_CTL A5 CCDV7N5_CTL B3 CCDV13P_CTL B11 LCDBLPWR_CTL B7 LENS_IN6 A12 LENS_IN5 B12 CHARGE_I R275 NC-0R/5% /0402 A11 F_CHARGE A13 LENS_V_SW A1
1
M4D/GSI3 M4C/GSI2 M4B/GSI1 M4A/GSI0 M3D M3C M3B M3A LENS INTERFACE M2D M2C M2B M2A M1D M1C M1B M1A
R231 TP254
1
/0402 33R/5%
CCLKOUT SPDATA SPCLK AFEVAL TGVAL VD HD CCD0 CCD1 CCD2 CCD3 CCD4 CCD5 CCD6 CCD7 CCD8 CCD9 CCD10 CCD11 PCLK VSUB1 VSUB2 LENS_SCLK LENS_SDATA RESET_N PWR_SW_ON PWR0N2 PWR0N4 PWR_ENB PDETECT
EJTAG INTERFACE
DDR INTERFACE
CCLKOUT SPDAT SPCLK AFEVAL TGVAL VIS HIS VID0 VID1 VID2 VID3 CCD/CMOS SENSOR INTERFACE VID4 VID5 VID6 VID7 VID8 VID9 VID10 VID11 CCLK SUBCNTL EXPCNTL
Z2C PORT INTERFACE
U200 COACH10M
RAMDAT0V13 RAMDAT1W5 RAMDAT2U13 RAMDAT3W4 RAMDAT4V5 RAMDAT5V14 RAMDAT6U6 RAMDAT7V8 RAMDAT8W11 RAMDAT9W7 RAMDAT10V12 RAMDAT11W6 RAMDAT12V6 RAMDAT13W12 RAMDAT14W8 RAMDAT15V9 U15 RAMADD0 V2 RAMADD1 V17 RAMADD2 U4 RAMADD3 U18 RAMADD4 V1 RAMADD5 U19 RAMADD6 U1 RAMADD7 U16 RAMADD8 U2 RAMADD9 W1 RAMADD10 U17 RAMADD11 U3 RAMADD12 RAMBA0 W2 RAMBA1 V3 RAMCAS#V18 RAMRAS#V19 RAMCLKW19 RAMCLK#W18 U7 RAMLDM V7 RAMUDM W14 RAMLDQS RAMLDQS#W13 V11 RAMUDQS W10 RAMUDQS# RAMCS# V16 RAMWE#W15 RAMVREFU12 RAMVREF1U8 W17 RAMCLKEN T17 VDDRAM R15 VDDRAM2 R14 VDDRAM3 R12 VDDRAM4 R8 VDDRAM5 R6 VDDRAM6 R5 VDDRAM7 T3 VDDRAM1 GND29 W16 GND31 V15 GND32 U14 GND33 R13 GND34 V10 GND35 W9 GND36 R7 GND37 U5 GND38 V4 GND39 W3 DAIN C1 DAOUT G6 DASCLK D1 DAFRM C2 DAMCLKD2 MICL_N A8 MICL_P B8 MICR_N A9 MICR_P B9 MICENB B4 SPKR_P C8 SPKR_N A7 LINEOUT C7 VCM F10 AREF C3
DDRD0 DDRD1 DDRD2 DDRD3 DDRD4 DDRD5 DDRD6 DDRD7 DDRD8 DDRD9 DDRD10 DDRD11 DDRD12 DDRD13 DDRD14 DDRD15
7 5 3 1
2 4 6 8
/8P4R/0402
RN203
R262 R263 R264 R265 R249 R209 R210 R204 R203 R200 R201 R205 R206 R266 R267 R268 R290 R207 R208 R211
1
39K/5%
0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402 0R/5% /0402
1
39K/5% /8P4R/0402
3 1 5 7 2 4 6 8
RN202
DDR_CLKP R202 NC
2 2
10K 5% 0402 / /
1 1 1 1
R250 0R/5%/0402
DDR1V8
3V3M
TP209 TP210
R234 100K/5% /0402
E2 SCL G5 SDA
CD
RESET
1 2
1 2 2 1
VCC
4 NC
GND 3
VDDPWRR270 CPWR
1 1
100K 5% / 0402 /
X5R/0402
VDDPWR D201 1
1 DCVIN
ADC INTERFACE
XLGPIO PINS
PWM PORT INTERFACE USB INTERFACE
R248
R244
R221
R252
PW M 0 PW M 1 PW M 2 PW M 3 PW M 4/ _G SI 4 PW M 5/ _G SI 5
T FLSH RI G I FPD N
L P 0 X G IO L P 1 X G IO X G IO L P 2
1 2 1
GD0 N3 GD9 N1 GD0 N2 GD1 N2 GD2 N2 GD3 N2 GD4 N2 GD8 N2 GD7 N2 GD6 N2 GD5 N2 GD8 N1 GD6 N1 GD5 N1 GD7 N1 GD4 N1 N GD GD N1 GD N2 GD N3 GD N4 GD N5 GD N6 GD N7 GD N8 GD N9 GD0 N1 GD1 N1 GD2 N1 GD3 N1 N4 GD0 GD1 N4 VD6 DP VD5 DP VD4 DP VD3 DP VD2 DP VD1 DP VD DP VD7 DP V D O E5 DCR V D O E9 DCR V D O E6 DCR VDOE DCR V D O E1 DCR V D O E2 DCR V D O E3 DCR V D O E4 DCR V D O E7 DCR V D O E8 DCR
V LK C I V LK C O
U BD S P U BD S N U BV U S BS U BI D S U BRSET S U BPW EN S R
20071227
PDETECT
1 1
R237
VIDEO_OUT 10K/5%/0402
R220
RB751V-40
R218
392R/1% /0402
C4 RSET
G7 CVBS F5 TESTMODE
C224
1 1
1UF/10V /X5R/0402
2
C225
1UF/10V /X5R/0603
2
H 8 H 9 H0 1 H1 1 H2 1 J8 J9 J 10 J 11 J 12 K 8 K 9 K0 1 K1 1 K2 1 L8 L9 L10 L11 L12 M 9 M0 1 M1 1 N 9 N0 1 N1 1 P8 P9 P10 P11 P12 R10 E13 E10 E7 G 8 H3 1 H 6 K 5 P5 E9 E6 G2 1 H 7 J 13 L5 M2 1 N 8 R11 R9
C13 C12 P6
F8 C17 A6 1 G 9 B16 F9
/SOD-523
R225 300K/1% 0402
2
X7R/0402
2
C220 0.1UF/10V
K 2 J1
P7 T1
K 1 L1 K 6 J3 K 3 L2
A 6 C6
HR P HL P
_ ZM PR _ ZM PI _ FM PI
3V3M
V LK C I V LK C O
DCVIN
C223 1UF/16V X5R/0603
2
1 2 3
VIN NC VOUT
CE VSS NC1
6 5 4
TP207
VDDPWR
1
2007/11/06 kaoder
U203 XC6209E332DR
USP6B
VDDPWR
CORE1V
R251
1
/0402 0R/5%
2
VCLKI
1
VCLKO
RTCXI
DCVIN RTCXO
R224 1
200K/1% /0402
2 1
BATTERY_LEVEL
1 1 2
4 3 1 1
C228 1UF/10V
X5R/0402
2
COG/0402
2
20071120
Y201 32.768K
20071207
GC200 0.2F/3.3V
B6 F6 F7 E5 C5
100K 5% /
2007/12/14 kaoder
2
C227 1UF/10V
100K 5% / 0402 /
100K 5% / 0402 /
/ 100K 5% / 0402
/ 0402
E1 H5 F1 J7 G2 H3 0R/5%/0402 H1 2 BATTERY_LEVEL F2 G1
RESET# PWRON0 PWRON1 PWRON4# PWRC INTERFACE PWRENB PDETECT VBAT VBAT_MSR CPWR
SD_CLK 1
LC100 0R/5%/0603
R247
R246
SD_CLK1
LENS_EXT HVDD_SW LENS_MOB12 F_READY CARD_DOOR MICL_N MICL MIC_N MIC MIC_ENB SPKRP SPKRN LINEOUT
20071228
TP200
1
R245
10K 5% 0402 / /
DDR_VREF DDR_CKEN
C202 NC
3V3M
DDR_CLKN
1 2
1 1 1 1
1 2
3-9
3. Schematics
3-6-6. KEY FPC BLOCK
J1
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3V3M
C1 0. 1u F
R1 10K/1%
C2
KEY_AD1
R2
100pF
1 2 3 4 5 6 7 8 9 10
200/1%
SW 1
SW 6
KeyFpc10Pin
LCD_EVF
R3 910/1%
1 2
SKRMAAE010
4 3
KEY_MENU_OK 1 2
R8 5.1K/1%
SKRMAAE010
4 3
SW 2
SW 7
KEY_PLAYBACK
FUNCTION
R4 1.5K/1%
1 2
SKRMAAE010
4 3
KEY_UP
R9 9.1K/1%
1 2
SKRMAAE010
4 3
SW 3
SW 8
SW 5
KEY_DISPLAY 1 2
R5 1.8K/1%
SKRMAAE010
4 3
KEY_RIGHT
R 10 18K/1%
1 2
SKRMAAE010
4 3
POWERON2
1 2
SKRMAAE010
4 3
VDDPWR
SW 4
SW 9
KEY_EV
R6 2.4K/1%
1 2
SKRMAAE010
4 3
KEY_DOWN
R 11 62K / 1 %
1 2
SKRMAAE010
4 3
S W 10
KEY_LEFT
R7 3.3K/1%
1 2
SKRMAAE010
4 3
3-10
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3-6-7.
CON305
22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
3. Schematics
LCD EVF USB LED AUDIO IN PORT BLOCK
VCOM LCD_CS SDATA SCLK LCD_HSYNC LCD_VSYNC LCD_D7 LCD_D6 LCD_D5 LCD_D4 LCD_D3 LCD_D2 LCD_D1 LCD_D0
CON306
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
EVF_C2V5 EVF_RESET
EVF_CLK
LCD_CLK
2
LCD_CLK1 LCD_CLK
10K/5% /0402 R321
1
TP312 20071212
LCD_D0 LCD_D1 LCD_D2 LCD_D3 EVF_5V LCD_D4 LCD_D5 LCD_D6 LCD_D7 SDATA SCLK EVF_CS EVF_5V
1
U300
R309
TP324 TP325 TP326 TP327 TP328 20071212 TP300 TP329 TP330 20071212
EVF_CLK
/0402 0R/5%
S6
5 VCC 4 A
EVFPWR_CTL
3V3M
R300
LCD_CLK1
R310 0R/5% /0402 C335 33PF/50V
2 1
TP315 20071212
1 2 3
IN GND CE
OUT 6 NC 5 4 SS
C310 0.022UF/16V X7R/0402
C320
2
/X7R/0402
SN74LVC1G3157DCKR
U302 LD6911_GU30
R317 100K/5% 0402
2.2UF/10V /X5R/0603
C321
2
FH34-22S-0.5SH
TP314 20071212
LCDPWR_CTL
1
20071212 TP316
3V3M
VCOM
C323
1 C324 4.7UF/6.3V
1
C322
2
4.7UF/10V/X5R/0603
1
L301
10UH
D300 CH511H-30PT
EVF_5V
R312 0R/5%
2
/0402 10K/5%
SOD-323
TP310 TP311
20071212
LCD_LED+ LCD_LEDVCOM
VCOM CS SDA SCL HSYNC VSYNC DCLK D7 D6 D5 D4 D3 D2 D1 D0 GND VDD DVDD V1 V2 V3 V4 VDD2 V5 V6 VDD3 VDD5 V7 V8 VGH VGL AGND FRP COMDC VCAC DRV VLED FB VCOM1
1 1 1
1 1
1
1
1
1 1
1
X5R/0603
1
FH23-39S-03SHW
1
20071126
R302 160K/1% 0402
VD D
EVFPWR_CTL
CE
N GD
EXT LX FB
2 4 6
TP301
1
RT9266-PE
1 2 MTXD 3 MRXD 4 5 6 7 8 9 10 RXD 11 TXD 12 FA15 13 FA13 14 FA19 15 FA16 16 FA17 17 FA14 18 3V3M 19 3V3M20 21
CON303
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1
0R/5% VDDPWR
R323
/0402
2
3V3M
1
1 2 3
IN GND CE
OUT 6 NC 5 4 SS
C300 0.022UF/16V X7R/0402
EVF_C2V5
TP331
U303 LD6911_GU25
R303 100K/5% 0402
STROBE_DET Connector
20071225 TP305
1
1 2
TP607 TP608
9 10
VDDPWR_1 1 PAD310 AFLED_CTL1 PAD309 STATUS_RLED 1 PAD305 1 STATUS_GLED PAD307 F_CHARGE 1 PAD301 F_READY 1 PAD300 F_TRIGGER 1 PAD302 3V3M 1 PAD303 DCVIN 1 PAD308 1 PAD306
FH33-10S-05SHW
FH33-10S-05SHW
EVFPWR_CTL
TOP_FPC Connector
KEY_FPC Connector
Debug Connector
FH23-21S-03SHW
SPKRN SPKRP PAD311 PAD312
R318 R314
1
MIC_ENB TV_OUT
1
NC-7.5K/5%/0402
VIDEO_OUT
1
L302
1
1
1.8UH/L2012
2
3V3M
C318 2.2UF/10V X5R/0603
7.5K/5% /0402
R316 1K/5% 0402
USB_DN
L300
R326 R325
1 1
USB_DP
C309
/0402 NC
2
USB_VBUS1 PWC0805HT900S
1 1
R313 1K/5%
2
1
USB_VBUS
1
1 2 3 4 5 6 7 8
FOR EMI
R327
1
NC-0R/5% /0603
C307 NC 0402
C308 NC/0402
J300
MIC
PAD313
C325 33UF/10V/TCTAL1A336M
2 2
MIC_N
1C305
0.1UF/10V/X5R/0402 2
20071203 PAD314
/0402
R41-8702
D301 NC
0603
R324
1
D302 NC
0603
D303 NC
0603 0402
2
R319
1
220PF/50V/X7R/0603
0R/5%/0603
2
R322
1
220PF/50V/X7R/0603
2
20071212
ESD_GND
ESD_GND
20071212
3-11
3. Schematics
3-6-8. MOTOR BLOCK
3V3M 1 R600 0R/5%/0603
1
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
LENS_STBY
3V3M
NC A VSS
LENS_MCK
LENS_SCLK LENS_SDATA LENS_CS ZM_PI ZPI R611 R610 0R/5%/0402 0R/5%/0402
28 26 25 27 34 35 36 37
RESET 1
U601
D N 24 GD
V C 47 C
4 Y
ZM_PR
LENS5V
NC_BU4S584G2
20
1
D601 MMPZ5232BPT
SOD-323 1
CON600
3V3M
IN2/MOB56/CPIN IN3/CPOUT IN4/EXT56 IN5 IN6 MOB12 MOB2 MOB3 EXT PI1 PI2 PI3 VM7_1 VM7_2 OUT7A OUT7B RNF7
1 3 5 7 9 11 13 15 17 19
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34
1 R603 ZPRSW IRIS2 IRIS4 SHUTTER_01 SHUTTER_02 1 R605 ZPISW ZOOM_DC+ ZOOM_DCFOCUS_STM_B FOCUS_STM_BLENS_TEMP FPISW 150R/5% /0402 2
3V3M
MGND
MGND LENS5V
TP605 TP606
38 39 22 23 12
VM34_245
1
TP604
2 ZPR IRIS1 IRIS3
150R/5%/0402 2
U601
SHUTTER_01
1
13 14 48 2 29 33
VM56_27 VM56_3
11 ZOOM_DC+ ZOOM_DCMGND
21 23 25 27 29 31
2 1
LENS5V
30 32 31
OUT6A10 OUT6B8
9 PGND6/RNF6 1 R601 1R/1% 0603 2 MGND
1
2 2
FM_PI
33 35
R612 0R/5%
1
2
FH26-35-03SHW
R2A30414NP
MGND
3-12
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
3-6-9.
DCVIN DCVIN DCVIN
POWER BLOCK
R445 NC-51R/5%
1206
R448 51R/5%
1206
R449 NC-51R/5%
1206
R450 NC-51R/5%
1206
1206
R451 NC-51R/5%
1206
1
R452 NC-51R/5%
L405 10UH
DDRPWR
D405 CH551H-30PT
R457
1
NC-0R/5% /0603
2
2 2
1 2
SOT-23
2
Q406 AO3419
1
1 3
DUMMYLAOD_MODE3
1
5V
3
Q408 AO3419
LEN5VS
2
DUMMYLAOD_MODE1
1
1 3
DUMMYLAOD_MODE2
1
Q412 NC-AO3418
Q410 NC-AO3418
Q411 NC-AO3418
0R/5%/0603
2
C423
1
3V3M
2
R401 R402
1
0R/5%/0603
2
2200PF/50V X7R/0402
0R/5% /0603
2
R403
1 1 1
0R/5%/0603
2
TP407
1 MOTPWR_CTL
R404 R405
0R/5%/0603
2
Q402 DDTC143EE-7-F
SC-75
3V3MS 1
1 1 1 1
L403
4.7UH
LENS5V
0R/5%/0603
2
D408 CH511H-30PT
D403 CH511H-30PT
5V
Q407 AO3419
1
D404 CH511H-30PT
5V DCVIN
1
DCVIN
1 1
D402
CCDV7N5S
DCVIN 1
L400 10UH
2
1
PV C C PV CL C VC C U SEL1 D
PV CH C
BT VA
U SEL5 D
NC-560PF/50V X7R/0402
2
PWR_ENB R4060R/5%/0402 1
SC-75
Q401 DDTC143EE-7-F
TP400 2
10UF/10V/X5R/0805
2
DCVIN
L406
3.3UH
CH511H-30PT SOD-323
C402
14
61
54 59 29 1
64
TP408
Q409 AO3419
R408
10UF/10V X5R/0805
2 2
C406
1
0.047UF/10V X7R/0402
2
DRAIN2H DRAIN2H1 DRAIN2L DRAIN2L1 INV2 FB2 SS23 PGND23 PGND23_1 DRAIN3H DRAIN3H1 DRAIN3L DRAIN3L1 INV3 FB3 SWIN4 OUT4 INV4 FB4 SWOUT4 GD N PG D N V EG R A V EF R
OUT5 NON5 INV5 FB5 DTC5 SWIN6 OUT6 INV6 FB6 SWOUT6 SWIN7 OUT7B INV7I INV7V FB7 NOV7 SWOUT7 STB1 STB23 STB4 STB5 STB6 STB7
52 44 45 46 43 2 53 40 41 3 62 58 37 38 39 36 63
1 1
C437
1
10UF/10V /X5R/0805
2
LCD_LED1 LCD_LED+ 2
CH551H-30PT
U400
BD9739KN
R434
7.5R/1%/0402
2
R416 34K/5%/0402
L402 10UH
C441 15 1
16 17 18 19 20
SCP
CT
SWIN4
1
RT
33
34
32
42 57 30 35
1 1 1 2 1 2 1 2
2
Q405 NC-AO3418
SOD-323
SOT-23
1 3
2 1 2
1 1 2 1
D401 CH511H-30PT
5V
PCBCLASS=PWR
1 1
SOT-23
Q403 AO3418
L401 10UH
1
TP402
2 2
C416
1
R432
1
5.1K/5%/0402
2
1 1
2200PF/50V /X7R/0402
1
OUT7B D407
L404
10UH
DCVIN
DCVIN
R407 NC
C408
LENS_V_SW
2007/11/26
44.2K/1% /0402 R430
2
D400
SC-75
Q400 NC-DDTC143EE-7-F
SWIN4
OUT4
2 1
2
CH551H-30PT
R422 C413
1
75K/5%/0402 NC/0402
2 2
1 OUT4
Q404 AO3418
CCDV13PS
D410
R424
1K/5% /0402
2
1
R426
1
100K/1%/0402
2
R427
1
1
10K/1% /0402
2
D409
R429
1
1
5.1K/1% /0402
2
LCDBL_CTL
3
1
1N4448HWT-7-F
PWR_ENB
C412
VREF1
1
TP403
SDO-523
CCDV13P_CTL CCDV7N5_CTL
0.1UF/10V X7R/0402
2
1 1 1 2 2
1 1
LCDBLPWR_CTL
2 1
2 C410 1
470PF/50V X7R/0402
3-13
3. Schematics
3-6-10. TOP FPC BLOCK
J1
3V3M
R1
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
com
com
C1 0.1uF
10K/1%
C2 100pF
SSS12L-V
R2 1.82K/1%
KEY_AD2
SW7
SW1
VDDPWR
com
com
C
2
C
1
TELE
R4 2.61K/1%
C3
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
3V3M
VDDPWR
MODEDIALSW KEY_AD2 PWR_SW_ON
ESE23J101
PWR_SW_ON
0.1uF
CON10PIN
WIDE
R3 1M
3V3M
R6 4.12K/1%
SW4
FACE_FOCUS
SKRMAAE010
100pF
R8 910R/1%
R9 7.32K/1%
SW5
MODE2
MODE3
MODE4
MODE5
MODE6
OIS_ON
1 2
SKRMAAE010
4 3
MODE1
3 4 5 6 7
8 9 10
2 1
1 2
4 3
ModeDialSW
C4
R5
10K/1%
R7
200R/1%
MODE0
MODE0 MODE1
COM
COM
C5 0.1uF
COM
COM
S1 ModeDialSW SRM-1001ST
R10 1.5K/1%
R12 16.9K/1%
R11 5.1K/1%
SW6
SHUTTER
MODE2
MODE6
4
2/2
3
R14 1.8K/1%
R15 9.1K/1%
R18 78.7K/1%
FOCUS
1
1/2
2
SKRNPBE010
MODE3
MODE7
R20 2.4K/1%
R19 18K/1%
MODE4
MODE8
R21 3.3K/1%
R22 62K/1%
MODE5
MODE9
3-14
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
3-7.
3-7-1.
3-15
3. Schematics
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3-16
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3-7-2. AF LED ASSY
3. Schematics
<SIDE A>
<SIDE B>
3-7-3.
<SIDE A>
<SIDE B>
3-17
3. Schematics
3-7-4. MAIN BOARD ASSY
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
LC500
<SIDE A>
3-18
B D
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3. Schematics
<SIDE B>
B D
3-19
3. Schematics
3-7-5. FLASH BOARD ASSY
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3-7-6. TRIGGER BOARD ASSY
3-7-7.
3-20
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3-7-8. TOP FPC ASSY
3. Schematics
3-21
3. Schematics
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
3-22
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
4. Adjustments
4-1.
4-1-1.
Image les contained in the internal memory should be handled as described below. <Procedure for handling images> When either of following work is necessary, as many as possible of the image les should be extracted from the camera's internal memory and then written into the internal memory in the repaired or replacement camera before the camera is returned to the customer. 1. When the replacement camera is provided. 2. If adjustment using the adjustment software is required. --->To prevent accidental erasure, carry out this step not only when the MAIN PWB ASSY is replaced but in all cases. *Note For PTP-connected cameras, carry out the procedure in "ii. Procedure for PTP-connected cameras and images that cannot be downloaded to a PC". <Image le transfer procedure> I. Procedure when images can be downloaded to a PC * If an xD-Picture card is inserted, data in the internal memory cannot be backed up. (1) Back up the images stored in internal memory. Create a folder (named and located so as to avoid any confusion with the user's images). Without inserting an xD-Picture card, connect the camera to a PC and copy the image les on the removable disk recognized by the PC to the folder created in the previous step. Check that the images can be displayed correctly on the PC. (2) Return the backed up image les from the PC to the camera. Turn the camera on without an xD-Picture card inserted and format the camera's internal memory. Without inserting an xD-Picture card, connect the camera to the PC and copy the image les from the folder containing the images backed up in the previous step onto the removable disk recognized by the PC. Check that the images can be displayed correctly on the camera. Delete the backup les created on the PC in step (1) (the user's image les). II. Procedure when images cannot be downloaded to a PC (1) Back up the images stored in internal memory. Insert an xD-Picture card to be used for image backup into the camera and format the card. From the SETUP menu, reset the frame numbers. Select image copying from the playback menu, select "Camera -> Card" for all the frames and then copy the images. Check that the images can be displayed correctly on the camera. (2) Return the backed up image les from the xD-Picture card to the camera. Before inserting the card, format the camera's internal memory. Insert the xD-Picture card containing the backed up copies of the user's image les. From the SETUP menu, reset the frame numbers. Select image copying from the playback menu, select "Card -> Camera" for all the frames and then copy the images. Remove the xD-Picture card and check that the images can be displayed correctly on the camera. From the SETUP menu, set the frame numbers to the default sequence. If the image le numbers have changed, always notify the user in writing that the image le numbers have changed. III. Procedure for PTP-connected cameras and images that cannot be downloaded to a PC (Images can only be backed up to a PC. * Normally, back up images using procedure II.) (1) Back up the images stored in the camera's built-in memory. Create an FAIS receive number folder (to ensure error-free user image management). Without inserting an xD-Picture card, connect the camera to the PC and check the image les in the camera on the PC. Then copy those les to the folder described on the previous page. Check that the images can be viewed successfully on the PC. (2) Return the backup image les from the PC to the camera. With no xD-Picture card inserted, turn the camera on and format the built-in memory. Using a card reader or similar device, check the xD-Picture card to be used for image le backup on your PC. Copy the image les from the image le backup folder on the previous page into the "DCIM\100_FUJI\" folder on the image le backup xD-Picture card. Using a safe procedure, remove the image le backup xD-Picture card from your PC. Load the image le backup xD-Picture card into the camera. Select "Copy image" in the Playback menu, select all the frames in "Card -> Camera" and then copy the images. Remove the xD-Picture card and check that the images can be viewed successfully. Delete the backup les (user image les) created on the PC in step (1).
4-1
4. Adjustments
4-1-2. Adjustment when replacing major parts
Replacing parts Adjustment item MAIN PWB Initialize * Self test & Lens test End Voltage Adjustment AF Adjustment Shutter Adjustment ISO Sensitivity Adjustment CCD Defect Correction Color Correction Flash Adjustment USB_ID Writing Language Setting
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Adjust the item shown by in the table below at the part replacement of LENS CONST, MAIN PWB ASSY, BATTERY PWB ASSY, FLASH BOTTOM ASSY (Other part replacements need not be adjusted). No. 0 1 2 3 4 5 6 7 8 9 10 LENS CONST MAIN PWB ASSY BATTERY PWB ASSY FLASH BOTTOM ASSY
* If the MAIN PWB ASSY has been replaced, upgrade the MAIN PWB Initialize before carrying out all the adjustments. Because the internal memory is formatted during the "MAIN PWB Initialize" procedure, take particular not to erase customer data when working on repair products.
4-2.
Measuring equipment Regulated power supply PC Brightness meter Color temperature meter Pattern box
4-3.
Pats.No ZJ00006-100 DC-R-J ZJ00615-100 ZJ00580-100 CR0130900U9 DC-R-K ZJ01692-100 ZJ01169-100 ZJ00008-100 ZJ00009-100 ZJ00611-100 ZJ00583-100 ZJ00653-100 ZJ00581-100 ZJ00553-100 CR013084899
4-2
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
4-4.
<Use the pattern box for Camera adjustment> Turn on the power supply in the pattern box. Afterwards, wait for about ten minutes so that the source of light may stabilize.
(1) Brightness 160 5 cd/m2 (with LB140 lter) No chart, center of pattern box Minolta brightness meter LS-110 or equivalent * Calibration method Place the lter (LB140) against the pattern box. With the lter (LB140) in contact with the brightness meter, adjust the pattern box brightness to 160 5 cd/m2.
LB140
<Calibration method of pattern box> (2) Color temperature 6100 50 K (with LB140 lter) No chart, center of pattern box Minolta color meter IIIF or equivalent * Calibration method Place the lter (LB140) against the pattern box. With the lter (LB140) in contact with the color temperature meter, adjust the pattern box color temperature to 6100 50 K.
4-3
4. Adjustments
4-5.
4-5-1.
The PC adjustment softwares are in a specied Web server, and both of these are the compression of ZIP form les. Therefore, after downloading these compression les from the Web server, the decompression of the le is necessary. In the decompression software, if the decompression of the ZIP form can be done, any software is OK. (Please prepare each one for the decompression software.) The decompression and the preservation method of the PC adjustment software and the rmware are described to the following. * The adjustment soft decompression and set up the adjustment card. <Step1> The adjustment software is downloaded from WEB, and software is installed in the PC. We have uploaded the ZJ01169-100.zip on our website: (https://denhin.fujilm.co.jp/csg_en/index.htm).
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
ZJ01169-100.zip
<Step2> ZJ01169-100 is a compression of ZIP type le.(Figure. 4-5-2). <Step3> Copy the "menu" le and "Firmware" folder in the "ZJ01169-100" folder to an xD-Picture card.(Figure. 4-5-3).
4-4
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4-5-2. Explanation of the "MENU" Adjustment Software
4. Adjustments
Use the adjustment xD-Picture card created in section 4-5-1 above to carry out adjustments on this model. Insert the adjustment xD-Picture card containing the "MENU" adjustment software into the camera's card slot and turn the camera on. The adjustment software launches automatically. [Operation guide] 4-way button: Selects items to be adjusted. MENU/OK button: Executes an adjustment. [Note] Only the adjustments shown in <Fig. 4-5-4> to <Fig. 4-5-8> are used. Do not select or execute any other adjustments.
<Fig. 4-5-4>
AF Adjustment
<Fig. 4-5-5>
4-5
4. Adjustments
Shutter Adjustment ISO Sensitivity Adjustment CCD Defect Correction Color Correction Flash Adjustment
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Fig. 4-5-6>
<Fig. 4-5-7>
USB_ID Write
<Fig. 4-5-8>
4-6
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
4-6.
[Note] Only when the MAIN PWB ASSY has been replaced,always carry out the "MAIN PWB Initialize" procedure before performing any other adjustments. Because the internal memory is formatted during the "MAIN PWB Initialize" procedure, take particular not to erase customer data when working on repair products. (Because the inspection image from the MAIN PWB ASSY manufacturing process may be contained in the internal memory, check that the memory has been erased after "MAIN PWB Initialize".) <Settings used for MAIN PWB Initialize>
FinePix S1000fd
DC COUPLER CP-04
AC Power Adapter
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Right button.
4-7
4. Adjustments
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 3> Press the Down button to select "UPdate FW" and then press the MENU/OK button.
<Step 4> When the screen shown on the right appears, press the Up button.
<Step 5> The indicator lamp starts ashing green and when MAIN PWB Initialize ends, the camera turns off. [Note] Do not turn the camera off while the indicator lamp is ashing. --> MAIN PWB Initialize ends.
4-8
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
4-7.
<Settings used for Self test & Lens test> Position the camera and the Gray chart so that the chart is180 20 mm from the front of the camera lens. Gray chart
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Right button.
Camera
Center
180mm20mm
4-9
4. Adjustments
<Step 3> Press the Down button to select "Self Test" and then press the MENU/OK button.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 4> If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.
4-10
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
4-8.
Digital voltmeter
<Step 1> Set the digital voltmeter to voltage measurement mode and then connect it to the Power Cable Jig clip. After checking the digital voltmeter and setting the regulated power supply to 5.0 V, plug the DC COUPLER into the camera. <Step 2> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 3> Adjust the voltage from the regulated power supply until 4.44V0.02V is displayed on the digital voltmeter.
4-11
4. Adjustments
<Step 4> When the screen shown on the right appears, press the Right.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 5> Press the Down button to select "Batt Check" and then press the MENU/OK button.
<Step 6> If the screen shown below (Figure. 4-8-1) appears, turn the camera off and remove the adjustment xD-Picture card. If "FAIL" (Figure. 4-8-2) appears, check the settings and carry out the adjustments again.
<Fig. 4-8-2>
4-12
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
4-9.
<Settings for AF Adjustment> (1) Set up the EFA chart and conversion lens so that they are 500 5 mm apart. (2) Position the chart so that the brightness of the chart surface is between 1000 200 LUX. (3) Position the 500 mm conversion lens 25 2 mm from the front end of the lens.
Lens Holder Attention when conversion lens is used. Convex side : Subject side. Plane : Camera lens side.
AF Adjustment
252 mm with the zoom set to wide. Note that the camera lens should not touch the conversion lens.
Fluorescent light stand EFA chart
Lens Stand
Washer (Plastic)
Lens Base Plate
Fixed Ring
Center
<EFA chart>
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on.
Camera
500 5 mm
4-13
4. Adjustments
<Step 2> When the screen shown on the right appears, press the Down button to change to "2".
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 3> When the screen shown on the right appears, press the Right button.
<Step 4> Press the Down button to select "EFA In" and then press the MENU/OK button.
4-14
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 5> If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.
4. Adjustments
4-15
4. Adjustments
4-10. Shutter Adjustment
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
[Notes] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. <Settings for Shutter Adjustment>
Maximum 5mm
Centerline
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Down button to change to "5".
Camera
Pattern box
4-16
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 3> When the screen shown on the right appears, press the Right button.
4. Adjustments
<Step 4> Select "Cali Shutter" and press the MENU/OK button.
<Step 5> If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.
4-17
4. Adjustments
4-11. ISO Sensitivity Adjustment
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
[Notes] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. <Settings for ISO Sensitivity Adjustment>
Maximum 5mm
Centerline
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Down button to change to "5".
Camera
Pattern box
LB140
4-18
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 3> When the screen shown on the right appears, press the Right button.
4. Adjustments
<Step 4> Press the Down button to select "ISO" and then press the MENU/OK button.
<Step 5> If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.
4-19
4. Adjustments
4-12. CCD Defect Correction
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
[Note] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. <Settings for CCD Defect Correction>
Maximum 5mm
Centerline
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Down button to change to "5".
Camera
Pattern box
4-20
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 3> When the screen shown on the right appears, press the Right button.
4. Adjustments
<Step 4> Press the Down button to select "Bad Pixel" and then press the MENU/OK button.
<Step 5> If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.
4-21
4. Adjustments
4-13. Color Correction
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
[Note] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. <Settings for CCD Defect Correction>
Maximum 5mm
Centerline
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Down button to change to "5".
Camera
Pattern box
LB140
4-22
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 3> When the screen shown on the right appears, press the Right button.
4. Adjustments
<Step 4> Press the Down button to select "Color" and then press the MENU/OK button.
<Step 5> If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.
4-23
4. Adjustments
4-14. Flash Adjustment
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
[Note] Darken the surroundings during calibration (a darkroom environment is ideal). <Settings for CCD Defect Correction> Adjust the positions so that the distance from the gray chart to the camera's ash unit is 280 10 mm.
280 10 mm
Centerline
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Down button to change to "5".
Camera
Gray chart
4-24
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 3> When the screen shown on the right appears, press the Right button.
4. Adjustments
<Step 4> Press the Down button to select "Cali Flash" and then press the MENU/OK button.
<Step 5> If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.
4-25
4. Adjustments
4-15.
4-15-1.
The PC adjustment softwares are in a specied Web server, and both of these are the compression of ZIP form les. Therefore, after downloading these compression les from the Web server, the decompression of the le is necessary. In the decompression software, if the decompression of the ZIP form can be done, any software is OK. (Please prepare each one for the decompression software.) The decompression and the preservation method of the PC adjustment software and the rmware are described to the following. * The adjustment soft decompression and set up the adjustment card. <Step1> The adjustment software is downloaded from WEB, and software is installed in the PC. We have uploaded the ZJ01692-100.zip on our website: (https://denhin.fujilm.co.jp/csg_en/index.htm). <Step2> ZJ01692-100 is a compression of ZIP type le.
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
ZJ01692-100.zip
<Step3> The FinePixS1000fd_USB_ID folder can be done by extracting it by Compression software. Copy the FinePixS1000fd_USB_ID folder to the C drive on the Adjustment PC.
4-26
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
4-16.
USB_ID Writing
<Step 2> When the window shown below appears, click the "OK" button.
4-27
4. Adjustments
<Step 5> When the screen shown on the right appears, press the Down button to change to "8".
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 4> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on.
<Step 6> When the screen shown on the right appears, press the Right button. select "USB SERIAL NUMBER", and press the MENU/OK button.
<Step 7> When the screen shown on the right appears, connect the USB cable to the PC.
4-28
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
<Step 8> In the "Welcome to the Found New Hardware Wizard" window, select "Install from a list or specic location (Advanced)" and then click "Next".
<Step 9> When the detection wizard window appears, click "Browse" button.
4-29
4. Adjustments
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 10> When the "Browse Folder" window appears, select one of the following and click the "OK" button. In Windows XP, select the C:\FinePixS1000fd_USB_ID > Driver > winme_xp folder containing the installed adjustment software. In Windows 2000, select the C:\FinePixS1000fd_USB_ID > Driver > win98_2k folder containing the installed adjustment software.
<Step 11> When the detection wizard window reappears, click "Next".
4-30
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 12> When the install conrmation window appears, click [Continue Anyway].
4. Adjustments
<Step 13> When the install conrmation window appears, click [Continue Anyway].
4-31
4. Adjustments
<Step 14> When the completion window appears, click "Finish".
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 15> Check that "Camera connect ok!!" is displayed in the software launched in <Step 3>, enter the serial number (8 digits) and then click "Start".
<Step 16> When the window shown below appears, click the "OK" button.
4-32
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 17> When the window shown below appears, click the "Cancel" button.
4. Adjustments
<Step 18> The window shown below appears and the camera turns off. Click "Exit" and remove the xD-Picture card.
4-33
4. Adjustments
4-17. Langeuage Setting
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
<Step 1> Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. <Step 2> When the screen shown on the right appears, press the Down button to change to "6".
<Step 3> When the screen shown on the right appears, press the Right button.
4-34
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4. Adjustments
<Step 4> Check the third number or letter from the left in the serial number and use the Down button to select the applicable model (Figure. 4-17-1). Then press the MENU/OK button. Model US-model EU/EG/EE-model CH-model 3rd digit in serial no. A~H,J,K Q~V W~Z Language Ship Area US Ship Area EX Ship Area CH
<Fig. 4-17-1>
<Step 5> If "Set ** OK" appears on the screen, turn the camera off and remove the adjustment xD-Picture card. "**" shows the selected language. The screen shows the display that appears when "Ship Area US" is selected.
4-35
4. Adjustments
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
4-36
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
5. Inspection
5. Inspection
5-1. Required Measuring Equipment
Measuring equipment Power supply Digital voltmeter Ammeter xD-Picture card TV Monitor DC COUPLER CP-04 POWER CABLE JIG Macro Chart LCD Inspection Data Face Detection Test Chart SD CARD ULTRA2 1GB Remarks AC adapter (AC-5V), Regurated power supply For general use For general use (able to measure 1mA or less) For general use TV monitor, minimum resolution 600 lines Common with adjustment JIG Common with adjustment JIG Resolution conrmation For LCD inspection (downloaded from WEB.) Checking face detection operation To check SD card recording Parts number
5-2.
Use DC COUPLER CP-04 and POWER CABLE JIG. The output current of the Regurated power supply must not become 2.5A or more. FinePix S1000fd
5-1
5. Inspection
5-3.
Sequemnce 1 Item External visual check Mode
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Auto mode
LCD-ON
EVF-ON
(6) Check that the live image and text is displayed. (7) Check that the live image is displayed. (8) Monitor a very bright subject and check that the live image does not dim or darken. (1) Zoom drive noise. (1) Check that there is no abnormal noise. (2) LCD screen. (2) Check that there is no edge blurringCheck that the screen display accurately tracks zooming. (3) Zoom operation (T <-> W). (3) Check that the zoom moves smoothly. (1) Apply a shock to the (1) Check for problems on the camera using the shock jig. LCD monitor. (2) Check that the camera recovers from synchronicity disruption. (Note) Do not apply shocks directly to the lens or card cover.
5-2
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Sequemnce 5 Item Resolution check Focusing check Mode
5. Inspection
Preparations for adjustment Method of adjustment Measuring Measurement points (measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions) Auto mode (1) Use a macro resolution ZJ00525-100 LCD-ON chart as the subject. (2) Set the camera to Macro (2) Press the 4-way button mode. (left) and check that the Macro icon (tulip) appears on the LCD monitor. (3) Set the camera up so that the chart lls the screen from corner to corner. (4) Press the shutter button to (4) The indicator lamp take a picture. lightsgreen -> Intermittently lights orange or green (recording) -> Turns off. (1) Check that STANDBY Movie mode (1) Select the mode dial to Movie shooting mode. appears on the LCD monitor. LCD-ON (2) Press S1 -> S2 and then (2) Check that movie/audio release S2 -> S1. recording begins. Check that REC appears on the LCD monitor. (3) After 5 seconds, press and (3) Check that movie/audio then release S1. recording ends and that the data is recorded on the xD card. Playback (1) Set the camera to Playback mode. (2) Press the 4-way button (2) Check that the movie is (down) to play back the played back on the LCD movie. monitor. Check that the sound is played back through the speaker. Playback (1) Plug the AV cable into the (1) The LCD monitor image disappears and the indicator lamp lights green. (2) Check images shot at (2) Where the horizontal macro resolutions (manual resolution is as follows: photography). 350 TV lines or better at the center and 300 TV lines or better at the periphery (NTSC). 300 TV lines or better at the center and 250 TV lines or better at the periphery (PAL). (3) Disconnect the AV cable from the camera. Turn the camera off camera.
5-3
5. Inspection
Sequemnce 9 Item Playback mode check Mode Playback
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Preparations for adjustment Method of adjustment Measuring Measurement points (measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions) (1) Start up in playback mode. (1) Press the <Playback> button. (2) If a message prompting (2) <BACK> the user to set the dateappears, press the buttonspecied on the right. (3) Check the playback image. (3) Check that the last imageshot appears, regardlessof whether it is automaticor manual.Check that the date is displayed in the YYYY.MM.DD forma. (1) Check that an erase (1) Select Erase -> Erase all from the menu and then press the OK button. message such as the following appears: Japan: OK? Overseas: ERASE ALL OK? China: OK? (2) Check that the recorded images are erased.
10
11
Auto mode
(2) Select "OK" and press the OK button. (3) Turn the camera off. Disconnect the xD card from the camera. (1) Insert a SD card. (2) Select the mode dial setting. (3) Set the power switch to ON. (4) If a message appears asking for the language and date to be set, press the specication button on the right. (5) Press the ash pop-up button to open the ash. (6) Set the ash mode to Forced Flash.
ZPU0512-100
(4) <BACK>
(7) Focus on any subject and press the shutter button to take a picture.
(6) Press the 4-way button (right) and check that the Forced Flash icon appears on the LCD monitor. Press the ash lamp unit down approximately 1 cm and check that the Forced Flash icon appears when the lamp is gently released. (7) The indicator lamp lights green -> Intermittently lights orange or green (recording) -> Turns off.
5-4
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Sequemnce 12 Item Mode Preparations for adjustment (measurement points, subject, other) (1) Press the Intelligent Face Detection button. (2) Set up the camera facing the face detection chart at a distance of 30 to 40 cm. (3) Press the S1 button.
5. Inspection
Method of adjustment Measuring Measurement points (VRs, waveforms, required values) equipment and jigs (VRs, positions) (1) Set Face Detection to ZJ01021-100 ON. (2) Check that the Face Detection icon is displayed on the LCD monitor. (3) Check that the focusing target is aligned with a face that has the Face Detection icon. (4) Set Face Detection to OFF.
13
Playback
14
(4) Press the face detection button. (1) Press the <Playback> button. (2) Check the playback image. (2) Check that the photographed image is displayed. (1) Select Erase -> Erase all from the menu and then press the OK button. (2) Select "OK" and press the (2) Check that the recorded OK button. (3) Disconnect the SD card from the camera. Turn the camera off. (1) Insert the LCD monitor inspection card. (2) Start up the camera in Playback mode. (3) Play back a completely black image. images are erased.
15
Playback
button. (3) Check that there are no noticeable dust ecks or stains (bright spots, etc.) on the screen. (4) Play back a completely (4) Check that there are no white (75%) image. noticeable dust ecks or stains (smears, ashing points, etc.) on the screen. (5) Change the setting with the (5) Play the above 2 frames EVF/LCD button. and perform the same checks. (6) Set the power switch to OFF. (7) Disconnect the LCD monitor inspection card.
5-5
5. Inspection
Sequemnce 16 Item Battery low check Backup check Mode Auto mode
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Preparations for adjustment (measurement points, subject, other) (1) Insert the xD-Picture card and set the DC COUPLER CP-04 and POWER CABLE JIG to the camera. (2) Set the power supply voltage. (3) Set the Mode dial to AUTO mode and turn the camera on. (4) Check that the pop-up ash opens and closes and check the backup. Method of adjustment Measuring Measurement points (VRs, waveforms, required values) equipment and jigs (VRs, positions) CR0130900U9 ZJ00580-100
(2) 5.00V 0.1 V (3) Check that the camera start up nomally. (4) Press the ash pop-up button to pop up the ash unit. Check that forced ash ring is displayed. Check that the ash mode reverts to AUTO when the 4-way key (right) is pressed after checking. (5) 4.86 V 0.05 V Check that the battery-low warning appears. (6) 4.40 V 0.05 V Check that the camera turns off.
LCD-ON
17
LCD-ON
(1) Insert the xD-Picture card CR0130900U9 and set the DC COUPLER ZJ00580-100 CP-04 and POWER CABLE JIG to the camera. (2) Set the power supply (2) 5.00 V 0.05 V voltage. (3) Set the Mode dial to AUTO mode and turn the camera on. (4) After the LCD monitor live (4) 500 mA or less. image appears, check the (Stable state => When current consumption. the IRIS/FOCUS is not operating.) If the current consumption exceeds the above value, it is OK if the current drops into the standard range within 10 seconds. If the current is still outside the standard range after 10 seconds,the camera is faulty. (5) Set the power switch to OFF. (6) Disconnect the xD card
18
Power off
from the camera. (1) Set the DC COUPLER CP-04 and POWER CABLE JIG to the camera. (2) Set the power supply (2) 5.00 V 0.05 V voltage. (3) Check the standby current (3) 0.5 mA or less when the power is turned OFF.
CR0130900U9 ZJ00580-100
5-6
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
Sequemnce 19 Item Shipping inspection (Inventory repairs only) Mode
5. Inspection
Preparations for adjustment Method of adjustment Measuring Measurement points (measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions) (1) Mode dial. (1) AUTO mode (2) SETUP frame no. (2) New: The default SETUP frame No. setting is Continuous, but to clear the number of frames in the frame number memory to zero, you should always change the setting to New before turning the camera off. (3) Flash. (3) Pop down (4) Battery and cards not (4) Normal inserted. (5) Internal memory. (5) Check that the internal memory is formatted. * Excluding customers camera. (6) Battery cover. (6) Closed (7) Power off. (7) The power supply is stopped after the camera's shutdown sequence ends.
5-7
5. Inspection
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
5-8
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
6. Parts List
6. Parts List
6-1.
6-1-1.
A118
A119 A120 A121
A126
A104
A125
A108
A103
A105
A111
A113
A112 A102
* Partway through the production process, units were added for which the instruction manual was provided on a CDROM, and the items bundled were changed. Supply of the old parts (Ref.A118-A121) ends when becoming out of stock. After stocks run out, use combinations of the new parts (Ref. A122-125).
A101
A114
Ref No. A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115
Parts No. CR013085199 CR013080599 CR013080499 CR074181499 CR013082099 CR013084499 CR013051299 FZ06957-200 CR0130999U9 CR013080699 CR013084899 CR013084999 FZ04792-100 CC013099899 CR173284999
Description UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL US LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL US CAMERA OFFICIAL SEAL
Comment Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness
Ref No. A116 A117 A118 A119 A120 A121 A122 A123 A124 A125 A126
Parts No. CR013085999 CR013081499 CR013081899 CR013081299 CR013081399 CR013080999 CR013088399 CR013088499 CR013088599 FZ07269-101 CC013099699
Description CARD (US) WARRANTY U SAFETY INSTRUCTION BASIC MANUAL E BASIC MANUAL S MANUAL E BASIC MANUAL ENGLISH BASIC MANUAL FRENCH BASIC MANUAL SPANISH CD ROM(SEVEN LANGUAGE MANUAL) LEAFLET
Comment Commonness Commonness Old Old Old Old New New New New Commonness
6-1
6. Parts List
6-1-2. EU-model
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
A104 A107
A106
A111
A113
A112 A102
A101
A114
Ref No. A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115
Parts No. CR013085199 CR013080599 CR013080499 CR074181499 CR013082099 CR013084699 CR013051299 FZ06957-200 CR0130999U9 CR013080699 CR013084899 CR013084999 FZ04792-100 CC013099799 CR173284999
Description UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL WEEE LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL CAMERA OFFICIAL SEAL
Comment
Description
Comment
6-2
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
6-1-3. E1-model
A107 A104
6. Parts List
A109 A110
A111
A113
A112 A102
A101
A114
Ref No. A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115
Parts No. CR013085199 CR013080599 CR013080499 CR074181499 CR013082099 CR013084699 CR013051299 FZ06957-200 CR0130999U9 CR013080699 CR013084899 CR013084999 FZ04792-100 CC013099799 CR173284999
Description UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL WEEE LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL CAMERA OFFICIAL SEAL
Comment
Description Comment BASIC MANUAL FRENCH BASIC MANUAL GERMAN BASIC MANUAL DUTCH CD ROM(SEVEN LANGUAGE MANUAL)
6-3
6. Parts List
6-1-4. EG-model
A107 A116
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
or
A122
A121
A104
A103
A108
A105
A106
A111
A113
A112 A102
* Partway through the production process, units were added for which the instruction manual was provided on a CDROM, and the items bundled were changed. Supply of the old parts (Ref.A117-A119) ends when becoming out of stock. After stocks run out, use combinations of the new parts (Ref. A120-121).
A101
A114
Ref No. A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115
Parts No. CR013085199 CR013080599 CR013080499 CR074181499 CR013082099 CR013084699 CR013051299 FZ06957-200 CR0130999U9 CR013080699 CR013084899 CR013084999 FZ04792-100 CC013099799 CR173284999
Description UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL WEEE LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL CAMERA OFFICIAL SEAL
Comment Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness
Description WARRANTY EG SAFETY INSTRUCTION BASIC MANUAL E MANUAL E BASIC MANUAL ENGLISH
6-4
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
6-1-5. EE-model
A107
6. Parts List
or
A121
A119
A104
A120
A103
A108
A105
A106
A111
A113
A112 A102
* Partway through the production process, units were added for which the instruction manual was provided on a CDROM, and the items bundled were changed. Supply of the old parts (Ref.A116-A118) ends when becoming out of stock. After stocks run out, use combinations of the new parts (Ref. A119-120).
A101
A114
Ref No. A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115
Parts No. CR013085199 CR013080599 CR013080499 CR074181499 CR013082099 CR013084699 CR013051299 FZ06957-200 CR0130999U9 CR013080699 CR013084899 CR013084999 FZ04792-100 CC013099799 CR173284999
escription UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL WEEE LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL CAMERA OFFICIAL SEAL
Comment Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness
escription SAFETY INSTRUCTION BASIC MANUAL E MANUAL E BASIC MANUAL ENGLISH CD ROM(SEVEN LANGUAGE MANUAL) LEAFLET
6-5
6. Parts List
6-1-6. CH-model
A107 A115 A119 A116
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
A120
A104
A109 A110
A111
A113
A112 A102
A118
A101
A114
Ref No. A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115
Parts No. CR013080399 CR013080599 CR013080499 CR074181499 CR013082099 CR013084799 CR013051299 FZ06957-200 CR0130999U9 CR013080699 CR013084899 CR013084999 FZ04792-100 CC013099799 CR013081699
Description UNITARY BOX C PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL CH LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL WARRANTY CH
Comment
Comment
6-6
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
6. Parts List
6-2.
M210
M202 M206
M208
M204
N.S. M203
M205
M209
N.S.=Not Supply
Ref No. M201 M202 M203 M204 M205 M206 M207 M208 M209 M210 Parts No. CR0130100U9 CR0130996U9 CR013010599 CR013010199 CR173210699 CR013010499 CR013010299 CR511154299 CR013040899 CR511154599 Description FRONT COVER CONST LENS RING UNIT DUST PROOF SPONGE FRONT COVER ISOLATION PIECE BATTERY SPRING HAND GRIP SCREW M1.4XL2 SCREW M1.7XL2.0 SCREW M1.7XL3.5 Comment Ref No. Parts No. Description Comment
6-7
6. Parts List
6-3. BATTERY COVER CONST
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
M301
M310
M309
M308
Ref No. M301 M302 M303 M304 M305 M306 M307 M308 M309 M310
Parts No. CR0130200U9 CR013020199 CR013020299 CR013020599 CR013020499 CR013020899 CR013020399 CR013020699 CR013020799 CR013040599
Description Comment BATTERY COVER CONST BATTERY COVER BATTERY LATCH BATTERY COVER SPRING BACK BATTERY COVER SPRING FRONT BATTERY COVER SPONGE BATTERY LATCH SPRING BATTERY SHEET METAL 1 BATTERY SHEET METAL 2 SCREW M1.4X2.0
Description
Comment
6-8
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
6. Parts List
6-4.
M435 M436 M434 N.S. M430 M440 M429 M428 M427 M425 M433 M423 M416 M441 M441 M417 M406 M405 M402 M411 M419 M418 M437 M422 M421 M424 M438 M431
Ref No. M401 M402 M403 M404 M405 M406 M407 M408 M409 M410 M411 M412 M413 M414 M415 M416 M417 M418 M419 M420 M421 M422 M423 M424 M425 M426 M427 M428 M429 M430 M431 M432 M433 M434 M435 M436 M437 M438 M439 M440 M441 M442 M443 Parts No. CR013019199 ESP3002169 CR511120699 EMI3003069 CR074169099 CR013012199 CR013012299 ECA0197019 CR013031299 CR0130302U9 CR013050299 CR511156099 EWI5111129 EWI5111139 CR013019499 CR0130309U9 CR0130400U9 CR0130301U9 CR013050199 CR013012699 CR013012599 CR013012099 FZ07059-100 CR0130110U9 CR0130997U9 CR013011999 CR013011499 CR013011399 CR013011299 CR013011599 CR013011799 CR013011199 CR013012499 CR013011699 CR013040199 CR511154599 CR511154399 CR013040999 CR511154799 CR013040299 CR511154499 CR013040699 CR511154299
MECHANICAL BLOCK
Description MAIN FRAME SPEAKER TRIPOD MIC XD CARD LABEL STRAP LEFT STRAP RIGHT CAP. CAP. MYLAR B BATTERY PWB ASSY BATTERY SEAL CAP. MYLAR A AF WIRE RED AF WIRE BLACK LED SILICONE AF LED PWB ASSY LENS CONST MAIN PWB ASSY LENS FPC SPONGE TAPE GASKET LCD HOLDER MYLAR LCD HOLDER LCD BACK COVER CONST KEY FPC UNIT LCD SPONGE OK BUTTON 4 WAY BUTTON 2 BUTTON 3 BUTTON USB COVER BACK COVER KEY SHEET METAL MYLAR FAKE BATTERY COVER SCREW M1.7XL4.5 SCREW M1.7XL3.5 SCREW M1.4XL3 SCREW M1.7XL3.5 SCREW M1.7XL2.5 SCREW M1.7XL3.0 SCREW M1.7XL4.5 SCREW M1.7XL3.5 SCREW M1.4XL2 Comment
M437
M437 M411
M412 M411 M410 M409 M408 M407 M435 M415 M437 M441 M437 M420
N.S.
M432 M439
M436
M426
M436
M401 M404
M440
M403 M442
M436 M439
N.S.=Not Supply
6-9
6. Parts List
6-5. TOP COVER CONST
M501
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
M517 M513
Ref No. M501 M501 M502 M503 M504 M505 M506 M507 M508 M509 M510 M511 M512 M513 M514 M515 M516 M517 M518 M518 M519 M520 M521 M522 M523 M524 M524 M525 M526 M527 M528 M528A M529 M530 M531 M532 M533 M534 M535 M536 M537 M538 M539 M540 M541 M542 M543 M544 M545 M546 M547 M548
Parts No. CR0130130U9 N.S. CR013018899 CR0130300U9 CR013018399 CR013018499 CR013015599 CR013013899 CR013013699 CR511156399 ELC6001009 CR013016299 CR013016199 CR013015399 CR511155899 CR013015199 CR511150999 CR013017599 CR0130170U9 CR0130196U9 CR0130308U9 CR013017399 CR0130303U9 CR013017699 CR0130171U9 CR013017299 CR013019699 CR013017499 CR013017799 CR013019799 CR013017899 CR013013199 CR013019599 CR013018599 CR013018999 CR013019099 CR013013999 CR013014099 CR013015299 CR013015499 CR511153699 CR013018199 CR511153399 CR511154899 CR013050499 CR0130304U9 CR0130307U9 CR013018299 CR511154299 CR511154399 CR511154599 CR013040499 CR511154199
Description TOP COVER CONST TOP COVER CONST TOP COVER MYLAR TOP FPC UNIT TOP COVER BUTTON STATUS LED POWER KNOB WT BUTTON SHUTTER BUTTON SHUTTER SPRING EVF EYE RING EYE CUP MODE DIAL COVER MODE DIAL STICKER MODE DIAL CAP MODE DIAL SPRING FLASH TOP COVER FLASH BOTTOM ASSY FLASH BOTTOM ASSY FLASH WIRE UNIT FLASH FIX FLASH DETECT PWB ASSY FLASH ADHESIVE FLASH UNIT FLASH BOTTOM COVER FLASH BOTTOM COVER FLASH HINGE FLASH SPRING FLASH SPRING FLASH SPONGE TOP COVER TOP COVER FUJI LOGO AF LENS AF LENS ADHESIVE WT SPRING WT SLIDER MODE DIAL STOPPER MODE DIAL SWITCH COVER FLASH LOCK FLASH LOCK PLATE FLASH LOCK SPRING FLASH LOCK PUSHER FLASH DETECT WIRE MYLAR FLASH BOARD FLASH DETECT WIRE UNIT FLASH BUTTON SCREW M1.4XL2 SCREW M1.4XL3 SCREW M1.7XL3.5 SCREW M2.0XL5.0 SCREW M1.4XL2
Comment
M519 M545
M512
M516
M525
M511 M524
M544
M527
M528A
M529 M540 M531
M528
M526
M532
M504 M503
M544
M502
N.S.=Not Supply
6-10
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
6. Parts List
6-6.
[NOTE]
Electrical parts
* Due to standardization, replacement in the parts list may be different from the parts list specied in the circuit or the components used on the set.
The components indicated by mark are critical for safety. When indicated parts by reference number, please include the board name.
Ref No. Parts No. Description Comment PWB diagram
[CONNECTOR] J1 ECN3071819
JACK
ECN3071589
JACK
DETECTOR SWITCH
FLASH BOARD
[SWITCH] ESW3017009 SWA1 DETECTOR SWITCH
6-11
6. Parts List
MEMO
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
6-12
Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual
7. Appendix
7. Appendix
7-1.
To ensure that after-sales srevice is performed accuratety, keep a record here of the technical updates issued that cover this device.
7-1