Professional Documents
Culture Documents
Aero Dina Mica
Aero Dina Mica
On
Flow Analysis & Simulation of Formula SAE Vehicle using CFD Techniques
Submitted in partial fulfilment of the requirements for the degree of
Flow Analysis & Simulation of Formula SAE Vehicle using CFD Techniques
A thesis submitted in partial fulfillment of the requirements for the Degree of Bachelor of Technology (Automotive Design Engineering) By Prafull Chandra Moulekhi (R140207040) Abhishek Dixit (R140207002) Rohit Aggarwal (R140207044)
Under the Guidance of Dr. Ugur Guven Professor of Aerospace Engineering (PhD) Nuclear Science and Technology Engineer (M.Sc)
Approved Dean
College of Engineering University of Petroleum & Energy Studies Dehradun May, 2011
CERTIFICATE This is to certify that the work contained in this thesis titled Flow Analysis & Simulation of Formula SAE Vehicle using CFD Techniques has been carried out by Prafull Chandra Moulekhi, Abhishek Dixit & Rohit Aggarwal under my supervision and has not been submitted elsewhere for a degree.
ACKNOWLEDGEMENT Major Project in the final year is an indispensable part of any engineering curriculum. It provides the students with an opportunity to gain experience on the practical application of their technical knowledge and to study the various theoretical aspects as well. We would like to thank our Project Guide Dr. UGUR GUVEN, Department of Aerospace Engineering for giving us this opportunity to work under his guidance on this project. His technical help and goal oriented approach has been unique and a stepping stone towards the successful completion of the project.
May 2011
TABLE OF CONTENTS Page TABLE OF CONTENTS LIST OF FIGURES LIST OF TABLES SUMMARY i v viii x
1. INTRODUCTION.....1 1.1 Introduction.. ....1 1.2 Objective....2 1.2.1 SUPRA SAE Competition......2 1.2.2 Structural Analysis .....................................................................................2 1.2.3 Materials.2 1.2.4 Aerodynamics.2 2. LITERATURE REVIEW .....3 2.1 Structural Analysis....3 2.2 Aerodynamics3 2.2.1 Main Bodywork..3 2.2.2 Wings..4 2.2.3 Under body Diffuser...4
2.2.4 Side Ducts...5 2.2.5 Spoilers...5 2.3 Aerodynamic Forces..6 2.3.1 Drag Force..6 2.3.2 Lift Forces7
2.4 Approaches to flow analysis8 2.4.1 Theoretical Approach .8 2.4.2 Experimental Approach..8 2.4.3 Computational Approach ...8 3. FEA ANALYSIS....9 3.1 Design Consideration for Roll cage..9
3.2 Material and Size optimization of Rollcage tubing..9
3.3 Structural Analysis...10 3.3.1 Front Impact..10 3.3.2 Side Impact...11 3.3.3 Rear Impact...11 3.3.4 Rollover Impact12 3.4 Rollcage Design Optimization.....13 3.4.1 Use of cross supports....13 3.4.2 Use of Gussets...15 4. FLUID DYNAMICS EQUATIONS...17
ii
4.1 Euler's and Bernoulli's equations17 4.1.1 4.1.2 Eulers Equation for viscous flow17 Bernoulli's equation..18
4.2 Navier- Stokes Equations for a viscous flow..19 4.3 Eulers Equations for an inviscid flow21 4.4 Navier stokes equation for a incompressible inviscid flow22 5. FLOW ANALYSIS..24 5.1 Modelling in Catia ..24 5.2 Creating Geometry in Gambit.25 5.2.1Creating Vertices.25 5.2.2 Creating Edges25 5.2.3 Creating Faces.26 5.3 Meshing..27 5.4 Parameters and initial boundary conditions...28 5.5 Flow Analysis in fluent...29 6. RESULT & ANALYSIS.....30 6.1 Flow Over Nose..30 6.2 Flow Over the body32 6.3 Flow Under body....33 6.4 Boundary Layer Separation35 6.5 Design Modification Based on result Obtained..39
iii
6.6 flow over Nose.40 6.7 Flow Over the Car Profile42 6.8 Flow Under Body.44 6.9 Boundary Layer Separation.46 6.10 Pressure Distribution Over and Below the Car..50 6.11 Drag Coefficient Plot.50 6.11 Lift Coefficient Plot...51 7. USE OF CFD RESULTS IN ENGINE PERFORMANCE CALCULATIONS52 7.1 Power Requirement..52 7.1.1 Wheel Resistance..52 7.1.2 Air resistance ...52 7.1.3 Gradient Resistance..53 7.1.4 Total Driving resistance....53 7.2 Drag Force Calculation at different speeds.54 8. CONCLUSION57 REFERENCES ..58
iv
LIST OF FIGURES Page Figure 2.1: Areas Concerning Aerodynamics...........4 Figure 2.2: Spoiler ........................5 Figure 3.1: Front Impact Stress Plot....10 Figure 3.2: Side Impact Stress Plot......11 Figure 3.3: Rear Impact Stress Plot.12 Figure 3.4: Rollover Impact Stress Plot.......................................................................................12 Figure 3.5: Optimized Front Impact Stress Plot..13 Figure 3.6: Optimized Side Impact Stress Plot....................................................................14 Figure 3.7: Optimized Rear Impact Stress Plot................14 Figure 3.8: Optimized Rollover Impact Stress Plot.....................................................................15 Figure 3.9: Front members with gussets......................................................................................16 Figure 3.10: Analysis results after Gusseting..........................................................................16 Figure 4.1: Bernoullis Equation.....18 Figure 5.1: Shape Design in Catia...............................................................................................24 Figure 5.2: Creating Vertices...........................................................25 Figure 5.3: Creating Edges..................................................................................................26 Figure 5.4: Creating Faces...............................26 Figure 5.4: Edge Mesh.27 Figure 5.5: Face Mesh.28
Figure 5.6: Specifying Boundaries.28 Figure 6.1.1: Velocity Contours at nose.........................................30 Figure 6.1.2: Static Pressure Contour at nose....................................................30 Figure 6.1.3: Contours of Turbulent Kinetic Energy.........................................31 Figure 6.1.4: Velocity Vectors at Nose.....................................................................................31 Figure 6.2.1: Velocity Contour over the car body.................................32 Figure 6.2.2: Contours of Turbulent Kinetic Energy over the car body....................................32 Figure 6.2.3: Velocity Vectors over the car body.............. ...................................33 Figure 6.3.1: Velocity Contour Under body..............................33 Figure 6.3.2: Static Pressure Contour Under body........................................34 Figure 6.3.3: Contours of Turbulent Kinetic Energy Under body.........................................34 Figure 6.3.4: Velocity Vectors Under body.......................35 Figure 6.4.1: Velocity Contour at front hoop.35 Figure 6.4.2: Velocity Contour at rear hoop..............................................36 Figure 6.4.3: Static Pressure Contour at front hoop..................................................................36 Figure 6.4.4: Static Pressure Contour rear hoop...................37 Figure 6.4.5: Contours of Turbulent Kinetic Energy at front hoop..........................................37 Figure 6.4.6: Contours of Turbulent Kinetic Energy...............................................................38 Figure 6.4.7: Velocity Vectors at front hoop...........................................................................38 Figure 6.4.8: Velocity Vectors at Rear ...................................................................................39 Figure 6.5: New Model in Catia .............................................................................................39
vi
Figure 6.6.1: Velocity Contours at nose..................................................................................40 Figure 6.6.2: Static Pressure Contour at nose..........................................................................41 Figure 6.6.3: Contours of Turbulent Kinetic Energy...............................................................41 Figure 6.6.4: Velocity Vectors at Nose...................................................................................42 Figure 6.7.1: Velocity Contour over the car body...................................................................42 Figure 6.7.2: Contours of Turbulent Kinetic Energy over the car body..................................43 Figure 6.7.3: Velocity Vectors over the car body....................................................................43 Figure 6.8.1: Velocity Contour Under body............................................................................44 Figure 6.8.2: Static Pressure Contour Under body..................................................................44 Figure 6.8.3: Contours of Turbulent Kinetic Energy Under body...........................................45 Figure 6.8.4: Velocity Vectors Under body.............................................................................45 Figure 6.9.1: Velocity Contour at front hoop ..........................................................................46 Figure 6.9.2: Velocity Contour at rear hoop.............................................................................46 Figure 6.9.3: Static Pressure Contour at front hoop..................................................................47 Figure 6.9.4: Static Pressure Contour rear hoop.......................................................................47 Figure 6.9.5: Contours of Turbulent Kinetic Energy at front hoop..........................................48 Figure 6.9.6: Contours of Turbulent Kinetic Energy...............................................................48 Figure 6.9.7: Velocity Vectors at front hoop...........................................................................49 Figure 6.9.8: Velocity Vectors................................................................................................49 Figure 6.10: Static Pressure XY Plot.......................................................................................50 Figure 6.11: Drag Coefficient Plot..........................................................................................50
vii
Figure 6.12: Lift Coefficient Plot...........................................................................................51 Figure 7.1: Aerodynamic force Vs. Vehicle Speed...............................................................52
viii
LIST OF TABLE Page Table 3.1: Material Selection10 Table 7.1: Change in total resistance with velocity..55
ix
Summary
This project is about determination of Engine performance at high speed, while calculating various resistances encountered by vehicle. Aerodynamic forces form major part of total resistances. To calculate these aerodynamic forces (coefficient of lift and drag) Flow simulation of different surface profiles has been performed using CFD techniques. We have analysed the structural integrity by using FEA analyses. 2-D analyses of surface profile of car has been done using GAMBIT and FLUENT. The results obtained from FLUENT has been useful in modifying the shape and carefully dealing with critical points like nose, driver compartment, extended body work at rear end, and wings. Results obtained from FLUENT were then used to calculate engine performance at varying speeds.
Chapter 1 Introduction
1.1 Introduction
Aerodynamic forces and moments, as well as tyre road forces, affect vehicle stability and control. Unlike the tyre forces which are primarily independent of speed, aerodynamic forces increase rapidly with speed. For example, aerodynamic drag determines the vehicles performance characteristics at high speed including maximum speed, forward acceleration at the higher speed and the braking acceleration. In addition to direct effects of aerodynamic forces the interaction of aerodynamic and the tyre forces can have a large effect on lateral acceleration performance. For example, aerodynamic down force (negative) increases the tyre loads and in turn increases the lateral force capability of tyres. One of the most important high tech tools for measuring aerodynamic performance in today's racing is Computational Fluid Dynamics (CFD). CFD is a computer-based technology that studies the dynamics of all things that flow. In Formula 1 racing, CFD involves developing a computer-simulated model of a race car and then applying the laws of physics to the virtual prototype to predict what the downforce or drag may be on various components of the car or how the car will respond in various wind conditions (head wind, cross wind or tail wind conditions), changing environmental conditions or on different road surfaces. We can use CFD to better visualize and improve their understanding of
how various designs will perform. It also allows them to experiment with more design variables with high resolution in space in a shorter amount of time. CFD allows engineers to use computer software like GAMBIT to divide components of a race car into specific cells or grids. For each of those cells, supercomputers which use CFD softwares like FLUENT, STAR-CD, FEMLAB and ANSYS CFX etc. to calculate mathematical equations that compute the velocity and air pressure of the wind as it passes over, under and around the specified components of the race car.
1
1.2 Objective This project is about modelling formula SAE vehicle while performing flow over analysis & simulation as well as structural analysis. The project is concerned with the simulation of the aerodynamic flow around the front section & over the surface of a Formula one racing car. This will help us in developing the curved surfaces that are least resistive to airflow and are viable for FSAE event.
1.2.1 SUPRA SAE Competition The SUPRA SAE competition is for university students to design, build and race a small formula style racing car. The competition is broken down in to different categories in which each team earns points. The body work and the aerodynamics of the vehicle cover the maximum points both in design and dynamic event. This is the primary objective of the project with the following questions required to be answered.
1.2.3 Materials: a) What are the material requirements for body & frame? 1.2.4 Aerodynamics: a) What SUPRA SAE rules apply to the bodywork? b) What generic shapes are most aerodynamically efficient? c) Would a forward wing be an effective way of avoiding under steer at speed? d) How far rearward should the bodywork extend? e) How can CFD be used to refine the bodywork design?
2.1 Structural Analysis The most important aspect of the vehicle design is the frame. The frame contains the operator, engine, brake system, fuel system, and steering mechanism, and must be of adequate strength to protect the operator in the event of a rollover or impact. The roll cage must be constructed of steel tubing, with minimum dimensional and strength requirements dictated by SAE.
The impact loading is simulated by restricting displacements at certain locations, and applying discrete forces at various points on the frame where the weight is concentrated. The applied forces are obtained by multiplying the deceleration value by the overall weight of the vehicle and driver
2.2 Aerodynamics When developing a bodywork package for any vehicle the aerodynamics of the bodywork should be considered. This is most beneficial in racing where aerodynamics can be tailored to give better vehicle economy, handling, and overall performance. While reviewing race car aerodynamics pertinent to Formula SAE there are three main areas to be reviewed: use of wings, use of an underbody diffuser and the general geometry of the main body work.
2.2.1 Main Bodywork Its most logical to focus on the main bodywork of the vehicle, with downforce production being a secondary objective. The bodywork is classically shaped around the occupants, and the various other sub-systems comprising of the vehicle; using this as the very basis of our design principals we move on to recognise the possible causes of drag in the vehicle. Since our vehicle engine is mounted at the rear and to provide sufficient cooling we have to provide a natural air flow over
3
the engine compartment. For the positioning of the radiator in the side we must also consider the effect of sidepods, the sidepod geometry can be used to generate downforce as well as influence the flow speed over the radiator.
2.2.2 Wings Inverted wings have been extensively studied for use on a Formula SAE. The study undertaken investigated the benefits of a wing package, as well as an initial performance prediction. The results drawn from this investigation were a similar or slower time in the acceleration event, a similar or faster time in the skid pan event, slower acceleration, higher cornering potential, higher slalom speeds, higher braking potential, and an increase in fuel usage. The conclusion drawn from this investigation was that a wing package would significantly benefit the vehicles performance in dynamic events.
Figure 2.1: Areas Concerning Aerodynamics 2.2.3 Under body Diffuser A secondary method of producing down force is an under body diffuser. A diffuser works on the principle that even a non-lifting body in the vicinity of ground effect can produce down force.
4
Since FSAE rules prohibit skirts to seal the under body of the car to the ground, the research regarding under body height to length ratio versus CL and CD must be considered.
2.2.4 Side Ducts Side ducts are mainly used in race cars for break and engine cooling of the vehicle. Conventional fender design trap much of the turbulent air coming of top and back of the tyre generated by rotation of tyres and wheels, combined with hot air moving through engine compartment and brakes, this generates losses. Side ducts provides a smooth outlet for these hot and turbulent gasses and turns the flow to exit smoothly along the side of the car instead of directly outward.
2.2.5 Spoilers The spoilers and air foils on the rear check may serve several purposes. The rear spoilers, which is attached either to the rear of the roof or the upper edge of the rear wings, has the effect of increasing the pressure acting on the rear deck area. This increase in pressure acting on the rear deck creates a down force at the most advantageous point as shown in the figure.
Figure 2.2: Spoiler The spoilers may also serve to stabilize the vortices in the separation flow, thus reducing the aerodynamic buffeting.
2.3 Aerodynamic Forces 2.3.1 Drag Force The air flow over a vehicle is complex and the aerodynamic drag is expressed by the semi empirical equation to represent the aerodynamic effect. Drag Force is calculated as: FD = V2 A Cd Where; FD = Aerodynamic Drag Force, N = air density, Kg/m3 V = velocity, m/sec A = Frontal Area, m2 Cd = Drag Coefficient
The total aerodynamic drag of a vehicle includes many factors which offer overall air resistance to the motion of vehicle. The types of aerodynamic drag components and their approximate relative contributions are;
Profile or Form Drag Induced or Lift Drag Surface or Friction Drag Interference
~55 - 60 % ~8% ~ 10 % ~ 15 %
a) Profile Drag
The profile drag depends upon the longitudinal section of the vehicle body, and plays the most important part as its contribution is the maximum. A careful choice of body profile, essential for
6
low drag, requires streamlines to be continuous and separation of boundary layers with its attendant vortices to be avoided. A vehicle body produces accelerated air flow and the induced drag is caused by the vortices formed at the sides of the vehicle travelling downwards.
b) Surface Drag
The surface or friction drag contributes substantially. It is due to the friction of the layers of air passing over the outside surface of the vehicle body. The friction loss on the boundary layer and the surface roughness has considerable effect on surface drag. If this surface is kept smooth, a laminar boundary layer will be maintained further along the vehicle than with the rough surface
2.3.2 Lift Force The pressure differential from the top to the bottom of the vehicle causes a lift drag. This lift force depends on the upper surfaces especially in areas of the leading edge of the hood, wind shield corners, leading edges of the cowl and underbody such as suspension, exhaust system &other components protruding, and the ground clearance. Lift is not a serious problem at normal speeds but at very high speeds it can affect stability and braking performance of the vehicle. The lift tends to reduce pressure between ground and wheels. This causes loss of steering control on the front axle and loss of traction on the rear axle. Lift Force is calculated as: FL = V2 A CL Where; FL = Aerodynamic Lift Force, N = air density, Kg/m3 V = velocity, m/sec A = Frontal Area, m2 CL = Lift Coefficient
2.4 Approaches to flow analysis There are three approaches to fluid dynamics: a) Theoretical Approach b) Experimental Approach c) Computational Approach 2.4.1 Theoretical Approach This approach uses the energy mass momentum equation to solve the flow problems. 2.4.2 Experimental Approach It uses experimental data measured from wind tunnel testing for determining fluid behaviour 2.4.3 Computational Approach This approach uses Numerical methods, computer programming and computer simulation softwares for fluid dynamics.
3.2 Material and Size optimization of Rollcage tubing According to rule book provided by SAE the minimum size of the steel tube should not be less than 1.0 inch (25.4mm) X 0.095 inch (2.4mm). We have chosen AISI 4130 steel tubes with dimensions of 1.25 inch (31.75 mm) X 0.079 inch (2mm) but the problem with this material was bending and weld ability. Since its a Medium Carbon, Chrome-Mo. Steel it requires preheating before welding.
AISI 4130 Type Size Medium Carbon Chrome-Mo. Steel 31.75 mm X 2mm
9
320 MPa Low Cost, Equal Strength, Weld able , Easily Available
Problems
Table 3.1: Material Selection Among many alternatives to this material we select AISI 1018 depending upon its availability, low cost and equivalent strength to AISI 4130.
3.3.1 Front Impact For the front impact case we have considered a sudden impact load with assumptions that two vehicles running at speed of 130kmph collides, with an impact pulse of 0.8 sec. In this case the impact force comes out to be 14000 N
10
Analysis is done by restraining nodes at the rear roll hoop while applying static force on front members. Analysis results shows that stresses are maximized at the front members with -----Maximum Stress = 1.2e+08 N/m2
For side impact we have considered a side on collision condition with a force of 7000 N. We restrained one of the side members with zero DOF and applying a force of 7000 N on the other side members. Analysis results shows that stresses are maximized at the front hoop with -----Maximum Stress = 5.11e+07 N/m2
For rear impact we have considered another car hitting from behind, with astatic equivalent force of 10000 N. For analysing it we restrained the front members with zero DOF and applying a force on the Rear roll hoop. Analysis results shows that stresses are maximized at the joint and cross support with Maximum Stress = 8.07e+07 N/m2
11
3.3.4 Rollover Impact In case of rollover condition the drivers head should not touch the ground and the cage must be strong enough to resist the crushing, hence a force of 1000 N is applied at the two roll hoops (together they forms a cage) front and rear while reducing the degree of freedom of lower frame member to zero. Analysis results shows that stresses are maximized at the rear roll hoop Maximum Stress = 8.07e+07 N/m2
Hence we require a bracing support (as shoulder harness) to reduce the stress intensity, and increase the factor of safety.
From the above results it is clear that the stress points are concentrated hence we provide the additional cross members and supports. Optimized results after the application of supports and gussets are as follows:
Figure 3.5: Optimized Front Impact Stress Plot Maximum Stress = 3.2e+07 N/m2
13
Figure 3.6: Optimized Side Impact Stress Plot Maximum Stress = 4.65e+07 N/m2
Figure 3.8: Optimized Rollover Impact Stress Plot Maximum Stress = 3.59e+07 N/m2
We applied Gussets to front members to prevent crushing of the cage in case of severe accidents. Analysis done after gusseting yield better results with improved factor of safety.
15
Figure 3.10: Analysis results after Gusseting Maximum Stress = 2.85e+07 N/m2
16
4.1 4.1.1
Euler's equation derives from the equation of motion by substituting in it the simplest possible constitutive equation for the stress tensor corresponding to an ideal fluid, expressed by Consideration of the individual components of the volume force S, shows that
4.1
4.3
4.4
4.5
These Euler equations do not give a full analysis of the flow, although by using them to approximate flow values is a common engineering method. This way, some understanding of the flow can be achieved, before a more final analysis can be done. In addition, the modelling of the inviscid flow by the Euler equations help to set the initializations conditions for the full viscous flow over the car body.
17
Figure 4.1: Bernoullis Equation The equation states that the static pressure Ps in the flow plus the dynamic pressure, one half of the density r times the velocity V squared, are equal to a constant throughout the flow. We call this constant the total pressure pt of the flow. As discussed on the gas properties page, there are two ways to look at a fluid; from the large, macro scale properties of the fluid that we can measure, and from the small, micro scale of the molecular motion and interaction.
18
4.6
4.7
2.1
4.8
4.9
4.10
The above equations are shown for a viscous flow. The speed of car is lower as compared to an aircraft can be considered low; the density of the flow doesnt changes as there is no flow in the altitude. The above equations are derived taken in consideration the change in density,
19
temperature so the terms of stresses appear in the equations. A viscous flow is one where the transport phenomena of friction, thermal conduction and/or mass diffusion are included. These transport phenomena are dissipative viz. they always increase the entropy of the flow. The equations that have been derived apply to a viscous flow, where mass diffusion is not included.
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
20
Energy Equation
4.18
4.3
Inviscid flow by definition: flow where the phenomenon of viscosity, mass diffusion, and thermal conductivity are neglected. The equations for an inviscid three dimensional flow are given below
4.19 4.20
21
Momentum Equations
4.21
4.22
4.4
The Navier stokes equation for an incompressible in viscid flow are derived from the equations given above. These equations can be obtained from the compressible form simply by setting density as a constant. With equal to a constant, .V=0.
22
4.23
For, full understanding of the flow over the vehicle, it is essential to analyze the full Navier Stokes Equations for full analysis. Each term must be either calculated or approximated in order to get accurate values. However, for such a problem, analytical solutions dont exist. Due to this, Programming and Numerical Solutions need to be used in order to get the necessary approximate results. In addition, CFD software such as Fluent has been used for full analysis.
23
5.1 Modelling in Catia With the help of surfacing and wire frame tool, surface of the vehicle initially developed according to the shape of the frame of the car. And the key Positions are noted to re-model it in gambit.
24
5.2 Creating Geometry in Gambit By using the position parameters, taken from the Catia model, 2 D model of the body was made in Gambit. Following are the steps used to form the 2D geometry of the car:
Figure 5.2: Creating Vertices 5.2.2 Creating Edges By joining different vertex edges are formed to make a wire frame.
25
26
5.3 Meshing Meshing is the breaking of physical/solution domain that can be a 2-D or 3-D domain into simpler sub domains/elements i.e. triangles, quadrilaterals for 2-D and tetrahedral, hexahedral for 3-D. Meshing make the solution easier and more accurate. The denser the meshing is more accurate the result will be but at the same time it will be more complex to solve the problem. Here we have used Quad/Tri mesh element & Pave type (creates unstructured grid of mesh element) to have more accurate flow near the car surface. To have more fine meshing first of all edges of the geometry are meshed. The edges of the car geometry have more mesh counts.
27
28
The parameters according to the operating conditions are given as follows: 1. Inlet velocity is given to the vertex in front of the car. 2. Pressure Outlet is given to the vertex rear of the car. 3. Lower & upper vertices are given as wall. 4. Car body is given as wall.
5.5 Flow Analysis in fluent Now, the fluent condition to the car geometry is given as follows: 1. 2 ddp version 2. Density based solver 3. Energy equation included. 4. Viscous model- K epsilon 5. Materials are air and aluminium for fluid flow and wall respectively. 6. Operating Pressure = 0 7. Air velocity at inlet =36 m/s. 8. Flow, turbulent kinetic energy & turbulent dissipation rate as Second Order Upwind. 9. All other parameters are used as default.
29
Figure 6.1.1: Velocity Contours at nose As shown in above figure, when the nose of the car encounters the air, velocity of air at nose becomes zero due to stagnation.
The figure shows that the pressure at the nose tip is about 2.34 KPa which is very high.
Figure 6.1.4: Velocity Vectors at Nose Since the edge of the nose is very sharp the velocity vectors are diverging to above the car which is not desirable.
31
Figure 6.2.2: Contours of Turbulent Kinetic Energy over the car body Flow over the body profile shows that velocity and pressure change is very high at different places and boundary layer separation occurring at two points, which is not good.
32
For race cars flow under the body should be more then over the car, as to reduce lift force. The pressure distribution under body shows that the pressure is slightly lesser to the ambient pressure.
Since the edges at the front roll hoop and rear hoop are very sharp and the velocity vectors start separating at this point.
36
A negative pressure gradient is observed at these points which should be minimised to have more uniform flow. For this Sharp edged are to be minimised and made uniform.
37
At these two point turbulence is maximum and which affecting the uniformity of the flow. The maximum turbulence kinetic energy is observed at front main hoop but as a negative pressure gradient is observed at the end of the vehicle the turbulent kinetic energy becomes lesser.
The velocity vectors are showing that the velocity vectors are separating at the bottom portion of the main hoop & car rear end and a reverse is observed at these points.
Figure 6.4.8: Velocity Vectors at Rear 6.5 Design Modification Based on result Obtained
The design was modified based on the results obtained from the analysis of first shape. Above model showing the new design in which the nose, profile, ground clearance, driver compartment, and rear compartment is modified.
Since in the new model the nose of the car is modified & sharp edges are modified the impact at the nose is minimised. The distribution of pressure is well distributed over the nose and no very high pressure is observed. The nose is so modified that the velocity vectors are allowed to pass bellow the car body to have less pressure under body. The turbulence kinetic energy is also less in this case as the flow is well diverged.
40
The nose is also lifted at front to avoid striking of it to ground at the time of pitching i.e. braking; also the flow becomes more to under body.
41
42
The velocity contours are well distributed over the profile of the car profile. The points where the negative pressure was more is now minimised.
Figure 6.7.2: Contours of Turbulent Kinetic Energy over the car body
43
Figure 6.8.1: Velocity Contour Under body Since the ground clearance is now reduced from 190 to 130 mm the velocity vectors are becomes denser under body.
Figure 6.8.4: Velocity Vectors Under body More air velocity resulting less air pressure and hence the lift force is less in this case.
45
Figure 6.9.4: Static Pressure Contour rear hoop Since the shape at front hoop and rear hoop is modified and the edges are now filleted, the flow is more uniform then the previous design.
47
Figure 6.9.6: Contours of Turbulent Kinetic Energy The turbulence kinetic energy in this model is less in this case as boundary layer separation is less in this case.
48
Figure 6.9.8: Velocity Vectors The velocity contours are more uniform then the previous design at the point of boundary layer separation. Also the reverse flow of the air is minimised to some extent.
49
Figure 6.10: Static Pressure XY Plot The XY plot is showing the pressure variation above and below the car. As in the figure the pressure above the car surface is more than that of the lower part, a lift is generated. Since the difference of these pressures is less, the lift will be lesser in this case.
The drag coefficient graph shows that drag coefficient for our vehicle is about 0.21, which is low and good for our vehicle. Hence energy used in resisting the aerodynamic force is also low and can be utilized in moving the vehicle.
The figure shows that drag coefficient is very low in this case, which is good for racing vehicles. Further the lift coefficient can be reduced by using front & rear wing to have negative lift. But since the vehicle is to run at low speed, use of wings may not be as beneficial as for vehicle with higher speeds. So the idea for using wings was dropped.
51
Acceleration resistance = Fa
50 90 130
7.1.2 Air resistance FL = *Cd*A* L*v2 Cd Drag Coefficient A Front Area L 1.199 kg/m3
7.1.4 Total Driving resistance FT = FR + FL + Fg + Fa FT = mg(cos + sin) + *Cd*A*L*v2 + ma At steady state a = 0 ; cos~ 1; sin ~ 0 FT = mg() + *Cd*A* L*v2
53
7.2 Drag Force Calculation at different speeds Power required P = FT*V M = 400 kg at = 0; FR = 4000 * 0.80 (for dry) = 3200 N Rdyn = 0.267 m Fz = mg(cos + sin) + *Cd*A*L*v2 L = 1.199 kg/m2
The total aerodynamic drag of a vehicle includes many factors which offer overall air resistance to the motion of vehicle. The types of aerodynamic drag components and their approximate relative contributions are Profile or Form Drag Induced or Lift Drag Surface or Friction Drag Interference ~ 55 - 60 % ~8% ~ 10 % ~ 15 %
Cooling & Ventilation System Drag ~ 10 % Rotating Wheel & other ~1%
Profile Drag Obtained from CFD Analysis = 0.19 Total Air drag ~ 0.28 Following are the values obtained for different velocities of FR, Fa, and Fz
54
FR 49.6 49.6 49.6 49.6 49.6 49.6 50 50.8 52 52.4 54 54.4 54.8
Fa 1.8 7.4 16.6 29.6 46.2 66.6 90.6 118.4 149.9 185.1 223 266 312.7
Fz 51.4 57 66.2 79.2 95.8 116.2 140.6 169.2 201.7 237.4 277.9 320.8 367.5
55
From the above graph it is clear that the aerodynamic forces are increasing in parabolic manner, with increase in speed. The aerodynamic forces are less significant at lower speeds but at higher speed these forces account for major source of vehicle resistance.
56
Chapter 8 Conclusion
After simulation of first model and the modified one, we conclude that the second model is selected as the final choice which could be used for creating the surface of formula 1 car. Following conclusions are made from the CFD analysis of both the models: The pressure profiles and contours justify the decision as the pressure is more evenly distributed. The velocity vectors show that the flow is more uniform. The area of negative pressure developed at the point near front hoop & rear end is minimised by giving fillets at those points. Pressure difference & turbulence at the points of boundary layer separation is highly minimised in modified model. The idea of lowering the ground clearance shows that the pressure under body is lowered resulting negative lift, which is required for to have traction at higher speeds. The rear body is extended in order to reduce the reverse flow in driver compartment. The nose profile is able to diverge the air stream in both directions (above and below) without any stagnation point. Reducing the driver compartment resulted in having more uniform air flow over the car body. The profile drag coefficient is as low as 0.19. From the total resistance data and graph it is clear that the aerodynamic forces are more prominent at very high speed and they increase proportionally to the square of velocity. And these forces in turn affect the engine performance at high speeds.
57
REFERENCES
R. Peyret, February 1996: Handbook of Computational Fluid Mechanics. Milliken & Milliken, 1995: Race Car Vehicle Dynamics. Thomas D Gillespie, 1999: Fundamentals of Vehicle Dynamics. Chan, L.Y, et al. Design/Build of a Formula SAE Vehicle. Paper, Adelaide: University of Adelaide Doddegowda, Punith, Aleksandr Bychkovsky and Albert George, Use of Computational Fluid Dynamics for the design of Formula SAE Race Car Aerodynamics: SAE Technical Papers, 2006
58