As these Work Method Statements may be used on building sites, the Risk Levels are as defined in the Principal Contractors Safety Alliance Subby Pack! as follo"s# Class $, %igh Risk# &oes the ha'ard have the potential to kill or permanently disable you( Class ), Medium Risk# &oes the ha'ard have the potential to cause serious in*ury or illness "hich "ould temporarily disable you( Class +, Lo" Risk# &oes the ha'ard have the potential to cause a minor in*ury "hich "ould not disable you( Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement CONDUIT INSTALLATION, PLACED PRIOR TO POURING CONCRETE WMS No 001 Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y ) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage&) C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check layout and mark out, ), -nstall disposable lids fro conduit bo.es to timber +, Lay conduit and accessories, /, 0ie do"n conduit, 0ripping and e.posed nails, Cuts and abrasions, Chemical glues, Cuts and abrasions + + + + 1nsure areas in particular "alk"ays are clear 2$,34 5se suitable gloves 2+,/4 Refer to MS&S and follo" safe "ork practices set out therein 5se suitable gloves 2+,/4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT ) CONDUIT INSTALLATION, PRIOR TO CONCRETE POUR WMS No3 0013 Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) %and tools to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement CONDUIT INSTALLATION IN T.E GROUND
WMS No 002 Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $,Check area for other services and confirm locations of any gas lines, po"er cables, telephone cables, "ater or se"er lines and tree roots, ), Check layout and mark out +,1.cavate trenches /,Lay conduit 3, Restore ground to client<s specifications Sun e.posure 0ripping 0ripping Manual handling ;alling in trenches 0rench collapse Services damage ;ire and e.plosion Personal in*ury 1lectric shock Confined spaces Manual handing 0ripping ) + + ) + + + + + $ ) ) + 5se skin protection 2+,/4 1nsure are is clear 2$,34 1nsure location of other services is confirmed and appropriate access permits obtained, 1nsure area is clear 2$,34 , Wear safety foot"ear 2+,/4 -mplement manual handling risk control procedures 2$,>4 1nsure trenches are as even and flat as practical 23,+4 ?arricade "ork area Provide shoring, benches or battering in accordance "ith WorkCover re:uirements 23,)4 Provide "arning lights if necessary overnight Comply WorkCover re:uirements 23,)4 -mplement risk management procedures 2$,>4 Confirm any e.isting installations are dead, ;ollo" Standard Working Procedures 2+,@4 -mplement manual handling risk control procedures 2$,>4 1nsure area is clear 2$,34 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: CONDUIT INSTALLATION IN GROUND WMS No3 0023 Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice under the supervision of a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +,7o previous e.perience re:uired, ?arricades to be used as appropriate Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) 1ngineering details to include depth of trenches in accordance "ith AS +999 and client<s specifications, =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) %and tools for trenching, barricades, "arning lights, %and tools and ladders to be checked daily, ?atteries for "arning lights, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement CONDUIT INSTALLATION IN WALLS AND CEILINGS WMS No 00# Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 13 Check layout and mark out 23 Check e:uipment is tagged #3 Secure fi.ings and supports 0ripping and e.posed nails, 1lectric Shock &ebris and noise from drilling Struck by falling ob*ects ;alling + $ + ) ) 1nsure area in particular "alk"ays are clear 2$,34 Wear safety foot"ear 2+,/4 5se only correctly tagged e:uipment 2/,)4 5se minimum drilling speed consistent "ith effective "ork, 5se goggles fro eye protection, suitable respirator and hearing protection 2+,/4 1nsure drill bits are sharp 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection "here appropriate 2+,34 Wear safety helmet 2+,/4 Restrict traffic Mobile scaffolds locked 23,/4 5se ladders in accordance "ith WMS 99@ 23,+4 1WP Certificate RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4
6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: CONDUIT INSTALLATION IN WALLS AND CEILINGS WMS No3 00#3 Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +,1WP Certificate +, 1WP training if using 1WP, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) -nstallation to comply "ith AS +999 and clients specifications, =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Portable tools, ladders, 1WP %and tools and ladders to be checked daily, 1WP in accordance "ith manufacturers recommendations, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement CA(LE AND LADDER TRA: INSTALLATION WMS No 00; Page 1of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check layout and mark out ), Secure fi.ings and supports using correct si'e bolts and fi.ings +, Cut ladders or trays to fit using drop sa" or $99mm angle grinder /, Secure ladders or trays to support 3, Remove sharp edges and protruding fi.ings 0ripping and e.posed nails &ebris and noise from drilling 7oise, eye in*uries, cuts and abrasions Cuts and abrasion from sharp edges Working at heights, falls Manual handling ?urns and fires from cutting and "elding + ) ) ) ) ) ) 1nsure are a in particular "alk"ays are clear 2$,34 Wear safety foot"ear 2+,/4 5se minimum drilling speed consistent "ith effective "ork, 5se P- respirator if appropriate2+,/4 5se appropriate eye protection 2+,/4 1nsure drill bits and sharp, 1nsure "orkpiece is clamped, 5se eye and hearing protection 5se gloves 2+,/4 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection "here appropriate 2+,34 5se gloves 2+,/4 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection "here appropriate 23,+4 ;ollo" manual handling risk control procedures 2$,>4 ;ollo" %ot Work procedures 2/,@4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: CA(LE AND LADDER TRA: INSTALLATION WMS No3 00; Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, +, 1WP 0raining if using 1WP, /, 1WP Certificate Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications, =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Portable drill, "elder, ladders, 1WP, grinder, drop sa", %and tools to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement WOR5ING IN RISERS WMS No 00< Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check location to dra"ing and reference to specification layout and mark out, ), Check for access to riser and have clear "orking are +, Check for confined spaces /, Check for ade:uate lighting 3, Protect al openings to risers @, -nstall "arning signs 0ripping and e.posed nails ;alling, falling ob*ects Restricted "orking space Work restrictions ;alling =b*ects falling + ) ) + ) ) 1nsure area in particular "alk"ays are clear 2$,34 Wear safety foot"ear 2+,/4 Wear safety helmets "ith chin straps 2+,/4 5se fall protection as appropriate 2+,34 Provide training and use entry permit "hen appropriate -mplement Confined Space Procedure if necessary 5se supplementary lighting if necessary ?uilder to provide protection 5sing appropriate sign eg, &A781R M17 W=RA-78 A?=B1! RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4
6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: WOR5ING IN RISERS WMS No3 00< Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +,Confined space training, +, Confined space training if applicable /, 7o previous e.perience re:uired, , Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Portable tools, %and tools to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement USING PORTA(LE LADDERS WMS No 00= Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Select appropriate ladder "ith regard to compliance "ith the relevant part of AS $CD) and the "ork to be done, ) -nspect the ladder for condition, +, Position ladder to ensure stability, 1lectric shock ;alling ;alling $ ) ) Metal or "ire reinforced ladders sha not !e "sed for any electrical "ork 23,+4 -nspect ladders3 Do no! se 'amage' ,a''e&s3 23,+4 Position ladders a minimum of $ metre from edges of slabs or floors, -ncrease this distance as "orking heights increases, Straight or e.tension ladders to be secured at top and bottom, Ladders needs to e.tend $ metre above landing level and to be long enough to "ork at least $ metre from the top 23,+4 Angle of ladder should be nominally $in / 23,+4 Al"ays face the ladder, When ascending or descending a ladder keep t"o hands and one foot on the ladder, 23,+4 ;all protection to be used "hen "orking above $,Cm 23,+4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: USING PORTA(LE LADDERS WMS No3 00= Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Ladders complying "ith the relevant part of AS $CD), Ladders to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLING LIG.T >ITTINGS WMS No 00? Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 13 Check layout and mark out, 23 Receive lights on site and confirm correct numbers and types #3 Confirm cabling re:uirements, ;3 -nstall light fitting base or bracket and terminate cabling or plug into lighting socket, <3 Complete the fitting of any other parts, =3 Confirm fitting is secure and installed to specifications, ?3 Clear area and remove isolation danger tags 0ripping and e.posed nails Struck by falling ob*ects Manual handling 1lectric shock 1lectric shock ;alling ;alling ;alling %and in*uries + ) ) $ $ ) ) ) + 1nsure area in particular "alk"ays are clear 2$,34 Wear safety foot "ear Aeep lifting area clear of people, 2/,D4 -mplement manual handling risk control procedures2$,>4 0est and confirm cables before commencing "ork, -solate and fit danger tags as appropriate 2+,$, +,)4 1nsure po"er tools and leads are tagged 2/,)4 5se ladders or platforms appropriately 23,+4 5se ladder or platform appropriately, 23,+4 5se ladder or platform appropriately, 23,+4 5se gloves, 2+,/4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 60o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: INSTALLING LIG.T >ITTINGS WMS No3 00? Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, +, 1WP 0raining if using 1WP, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications, =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Portable drill, leads and ladders, %and tools and ladders to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> SWITC.(OARDS WMS No 00@ Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 13 Confirm installation specifications, 23 Prepare installation area and confirm ade:uate space including door s"ing for maintenance, #3 Arrange for crane or other mechanical handling e:uipment if needed, ;3 Receive s"itchboard on site including test certificates, <3 0ransfer s"itchboards to installation location =3 Mark out location ensuring coordination "ith other services, ?3 -nstall s"itchboard to manufacture<s and client<s specifications, @3 Commission s"itchboard A3 Clean area 7EA %and in*uries, tripping and e.posed nail 7EA ;alling ob*ects Manual handling ;alling ob*ects Manual %andling 7EA Manual handling 1lectric shock, e.plosion %and in*uries 7EA + 7EA ) ) ) ) ) $ + 7EA 1nsure Area in particular "alk"ays are clear 2$,34 Wear safety foot"ear 2+,/4 5se suitable gloves 2+,/4 7EA Aeep lifting area clear of people 2/,D4 -mplement manual handling risk control procedures 2$,>4 5se mechanical handling e:uipment 2/,D4 -mplement manual handling risk control procedures 2$,>4 7EA -mplement manual handling risk control procedures 2$,>4 Carry out preFcommission test and isolation procedures 2@,+,@,/4 5se suitable gloves 2+,/4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT ) INSTALLATION O> SWITC.(OARDS WMS No3 00@ Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o +omp,e!e Bo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor,
$, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s Co'es of P&a+!%+e, Leg%s,a!%on AS+999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Portable drills, ladders, appropriate mechanical handling e:uipment, Ma%n!enan+e C0e+/s) Mechanical handling e:uipment to be check in accordance "ith Statutory and manufacturer<s re:uirements,
%and tools and ladders to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> P:ROTENAC 2MIMS4 CA(LE WMS No 00A Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 13 Check location to dra"ing and specification layout and mark out 23 Confirm cable specification and condition, #3 Confirm cable supports on conduits have been installed to specifications, ;3 -nstall rollers on other protection to client<s specifications, <3 -nstall cable stands to client<s specifications, =3 -nstall cable manually "ith rope or "inch as appropriate to client<s specification, ?3 Cut any e.cess cable and seal e.posed ends to manufacturer<s recommendations @3 LocateEdress cable to fi. in position to client<s specification, 0ripping and e.posed nails 7EA ;alls ;alls Manual handling Manual handling %and in*uries ;alls + 7EA ) ) ) ) + ) 1nsure area is clear 2$,34 Wear safety foot"ear 2+,/4 7EA Refer to WMS 99/, cable and ladder tray installation 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection as appropriate 2+,34 -mplement manual handling risk control procedures 2$,>4 -mplement manual handling risk control procedures 2$,>4 5se suitable gloves 2+,/4 5se toll in accordance "ith manufacturer<s instruction 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection as appropriate 2+,34 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: INSTALLATION O> P:ROTENAC 2MIMS4 CA(LE WMS No3 00A Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Manufacture<s recommended tools, Ma%n!enan+e C0e+/s) %and tools to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> LIG.TING LOOMS WMS No 010 Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 13 Check dra"ings to confirm loom locations and specifications, 23 Receive cable and sockets bases on site and confirm correct types, si'es and numbers, #3 Construct lighting looms to client<s specifications, ;3 Label each loom "ith distribution board and circuit number, <3 -nstall looms to client<s specifications, =3 Confirm socket locations and fi.ings to client<s specification ?3 -nstall circuit feeds and s"itch "ires to client<s specifications, @3 Clean area, 7EA Struck by falling ob*ect Manual handling %and in*uries 7EA 1lectric shock ;alls ;alls 1lectric shock ;alls %and in*uries 7EA + ) + 7EA $ ) ) $ ) + 7EA Aeep lifting area clear of people 2/,D4 -mplement manual handling risk control procedures 2$,>4 5se tool appropriately 7EA 5se only correctly tagged e:uipment 2/,)4 5se ladders in accordance "ith WMS 99@ 23,+4 5se ladders in accordance "ith WMS99@ 23,+4 5se only correctly tagged e:uipment 2/,)4 5se ladders in accordance "ith WMS 99@ 23,+4 Wear suitable gloves 2+,/4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: INSTALLATION O> LIG.TING LOOMS WMS No3 0103 Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Portable tools, ladders Ma%n!enan+e C0e+/s) %and tools and ladders to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> CA(LE SUPPORTS WMS No 011 Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check location to dra"ing and specifications ), Receive cable supports on site confirming correct type, si'e and number +, Mark out route of cable supports to specifications confirming clearance of other services /, -nstall supports to client<s specifications supporting as necessary and using correct si'e bolts, 3, Confirm tightness of fi.ings @, -nstall cable supports >, Clean area 0ripping and e.posed nails Struck by falling ob*ects Manual handling ;alling 1lectric shock ;alling ;alling Struck by falling ob*ects ;alling %and in*uries + ) ) ) $ ) ) ) ) + 1nsure area is clear 2$,34 Wear safety foot"ear 2+,/4 Aeep lifting area clear of people 2/,D4 -mplement manual handling risk control procedures 2$,>4 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection as appropriate 2+,34 1nsure po"er tools and leads are tagged 2/,)4 5se ladders in accordance "ith WMS 99@ 23,)4 5se ladders in accordance "ith WMS 99@ 23,)4 Aeep lifting area clear of people 2/,>4 5se ladders in accordance "ith WMS 99@23,+4 5se fall protection as appropriate 2+,34 5se suitable gloves RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: INSTALLATION O> CA(LE SUPPORTS WMS No3 0113 Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 1WP Certificate +, 1WP Certificate if using 1WP, /, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Portable drill, ladders, 1WP %and tools to be checked daily, 1WP in accordance "ith manufacture<s recommendations, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> MAINS WMS No 012 Page 1 of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Liase "ith Supply Authority to coordinate to supply, ), =btain Supply Authority Certificates and check dra"ings, +, Coordinate shutdo"ns "ith client, /, Receive mains on site, 3, Shut do"n and install &A781R 0ags, @, Remove e.isting mains terminations if applicable, >, -nstall mains to specifications, C, 0erminate ne" mains to specifications, 7EA 7EA 7EA ;alling ob*ects Manual handling 1lectric shock 1lectric shock 1lectric shock 1lectric shock 7EA 7EA 7EA ) ) $ $ $ $ 7EA 7EA 7EA Aeep lifting area clear of people 2/,>4 -mplement manual handling risk control procedures 2$,>4 Confirm &1A& before commencing "ork 2@,$4 Confirm &1A& before commencing "ork 2@,$4 Confirm &1A& before commencing "ork 2@,$4 Confirm &1A& before commencing "ork 2@,$4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4
6 0o be read in con*unction "ith 71CA Safety 8uide fro 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> MAINS WMS No 012 Page 2 of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34
D, Confirm installation to dra"ings and specifications and ensure connections are tight, $9, Clean area, $$, 0est installation, $), Liase "ith Supply Authority for inspection and test, $+, Remove &A781R 0ags, $/, 1nergise supply, $3, -nstall signs or labels as re:uired, 1lectric shock %and in*uries 1lectric shock 7EA 7EA 1lectric shock %and in*uries
$ + $ 7EA 7EA $ + Confirm &1A& and identify cables before commencing "ork 2@,$4 Wear suitable gloves 2+,/4 Confirm &1A& and identify cables before commencing "ork 2@,$4 7EA 7EA ;ollo" Standard Working procedures, 2Chapter @4 5se tools appropriately 23,@4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4
6 0o be read in con*unction "ith 71CA Safety 8uide fro 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: INSTALLATION O> MAINS WMS No3 012 Page # of # Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 1WP Certificate /, 7o previous e.perience re:uired, +, 1WP training if using 1WP, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) -nstallation to comply "ith AS +999 and clients specifications, =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Portable tools, ladders, 1WP %and tools and ladders to be checked daily, 1WP in accordance "ith manufacturers recommendations, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> SWITC.(OARD CONNECTIONS WMS No 01# Page 1 of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Confirm s"itchboard meets and has been installed to specifications ), Confirm cables to be connected meet specifications and all cables have been installed, Check any specific re:uirements have been met, +, 8roup cables together as they enter s"itchboard and fi. "ith cable ties, /, Separate cables into groups of like destination, Seal or plug any unused cable entries, 3, Mark each conductor prior to removing any secondary insulation, @, 8roup conductors of like destinations and fi. into a loom system >, Align and terminate each conductor into its correct location, 7EA 7EA %and in*uries 1lectric shock 7EA %and in*uries 1lectric shock 7EA 7EA + $ 7EA + $ 7EA 7EA 5se suitable gloves 2+,/4 Confirm &1A& before commencing "ork 2@,$4 7EA 5se suitable gloves 2+,/4 Confirm &1A& before commencing "ork 2@,$4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> SWITC.(OARD CONNECTIONS WMS No 01# Page 2 of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 C, Check and tighten all terminations and connections, D, Confirm installations meet specifications, $9, -nstall labels, signs or markings as re:uired, $$, Clean s"itchboard, $), Confirm all circuits have been completed and &A781R 0A8 any incomplete circuits, $+, 0est and commission s"itchboard using relevant procedures, Confirm phase rotation of all + phase e:uipment, $/, Complete records, 1lectric shock 7EA 7EA %and in*uries 7EA 1lectric shock 7EA $ 7EA 7EA + 7EA $ 7EA Confirm &1A& before commencing "ork 2@,,$4 7EA 7EA 5se suitable gloves 2+,/4 7EA ;ollo" safe "ork practices 2@,+4 7EA RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: INSTALLATION O> SWITC.(OARD CONNECTIONS WMS No3 01# Page # of # Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, +, 1WP 0raining if using 1WP, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications, =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Portable drill, leads and ladders, %and tools and ladders to be checked daily, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> NEW WOR5 IN ECISTING SWITC.(OARDS WMS No 01; Page 1 of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check dra"ings and specifications, ), Arrange isolation of section of, or complete s"itchboard "ith client, +, -solate section of, or complete s"itchboard, install insulating barriers, /, ;it &A781R 0A8S to isolation devices, 3, 0est that "ork area has been safely isolated, @, Complete installations to client<s specification, >, Check and tighten all terminations and connections, 7EA 7EA 1lectric shock 7EA 1lectric shock 1lectric shock 1lectric shock 7EA 7EA $ 7EA $ $ $ 7EA 7EA Confirm &1A& before commencing "ork 2@,$4 ;ollo" Standard Working Procedures 2Chapter @4 7EA Confirm &1A& before commencing "ork 2@,$4 ;ollo" Standard Working Procedures 2Chapter @4 0est and identify cables before commencing "ork 2@,$4 Confirm &1A& before commencing "ork 2@,$4 ;ollo" Standard Working Procedures 2Chapter @4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> NEW WOR5 IN ECISTING SWITC.(OARDS WMS No 01; Page 2 of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 C, Confirm installation to client<s specifications, D, ;it &A781R 0A8S to any incomplete "ork, $9, -nstall labels, signs or markings as re:uired, $$, Clean "ork area, $), 0est and commission ne" installation follo"ing relevant procedures, Confirm phase rotation of all + phase e:uipment, $+, Complete records, 7EA 7EA 7EA %and in*uries 1lectric shock 7EA 7EA 7EA 7EA + $ 7EA 7EA 7EA 7EA Wear suitable gloves 2+,/4 ;ollo" Standard Working Procedures 2Chapters ) and @G RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT ) INSTALLATION O> NEW WOR5 IN ECISTING SWITC.(OARDS WMS No3 01; Page # of # Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o +omp,e!e Bo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor,
$, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ) Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 1WP Certificate +, 1WP training if using 1WP, /, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) -nstallation to comply "ith AS+999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Portable tools, ladders, 1WP Ma%n!enan+e C0e+/s) hand tools and ladders to be checked daily, 1WP in accordance "ith manufacturer recommendations,
Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> SU(MAINS WMS No 01< Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check location to dra"ings and specification layout and mark out ), Plan installation so as to "ork to"ards the main s"itchboard, +, Confirm cable specifications and condition, /, -nstall cable to client<s specifications, 3, 0erminate sub mains to specifications,
@, Clean area >, 0est installation C, Remove &A781R 0A8S D, 1nergise main s"itchboard, $9, -nstall signs or labels are re:uired, 0ripping and e.posed nails 1lectric shock 7EA ;alls Manual handling 1lectric shock 1lectric shock %and in*uries 1lectric shock 7EA 1lectric shock %and in*uries + $ 7EA ) ) $ $ + $ 7EA $ + 1nsure area is clear 2$,34 Wear safety foot "ear 2+,/4 Connections to the main s"itchboard to be made =7LH "hen it is C=7;-RM1& &1A& 2@,$4 7EA 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection as appropriate 2+,34 -mplement manual handling risk control procedures 2$,>4 1nsure that no bare conductors can contact any live parts, 1ffectively insulate both ends of all cables near any live parts, Restrain the ends of all cables near any live parts, -solate main s"itchboard and install &A781R 0A8S, C=7;-RM1& &1A& before making any connections 2@,$4 5se suitable gloves 2+,/4 C=7;-RM1& &1A& and identify cables before commencing "ork 2@,$4 7EA ;ollo" Standard Working Procedures 2Chapter @4 5se tools appropriately 23,@4 Wear suitable gloves 2+,/4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide fro 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT : INSTALLATION O> SU(MAINS WMS No3 01< Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 1WP Certificate, /, 7o previous e.perience re:uired, +, 1WP training if using 1WP, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Portable drills, ladders, appropriate mechanical handling e:uipment, Ma%n!enan+e C0e+/s) Mechanical handling e:uipment to be checked in accordance "ith Statutory and manufacturer<s re:uirements, %and tools and ladders to be checked daily, 1WP in accordance "ith manufactureIs recommendations, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLATION O> POWER AND LIG.T CA(LING WMS No 01= Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check location to dra"ings and specification layout and mark out ), Plan installation so as to "ork to"ards the main s"itchboard, +, Confirm cable specifications and condition, /, -nstall cable to client<s specifications, 3, 0erminate submains to specifications, @, Clean area >, 0est installation C, Remove &A781R 0A8S D, 1nergise main s"itchboard, $9, -nstall signs or labels are re:uired, 0ripping and e.posed nails 1lectric shock 7EA ;alls Manual handling 1lectric shock 1lectric shock %and in*uries 1lectric shock 7EA 1lectric shock %and in*uries + $ 7EA ) ) $ $ + $ 7EA $ + 1nsure area is clear 2$,34 Wear safety foot "ear 2+,/4 Connections to the main s"itchboard to be made only "hen it is C=7;-RM1& &1A& 2@,$4 7EA 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection as appropriate 2+,34 -mplement manual handling risk control procedures 2$,>4 1nsure that no bare conductors can contact any live parts, 1ffectively insulate both ends of all cables near any live parts, Restrain the ends of all cables near any live parts, -solate main s"itchboard and install &A781R 0A8S, C=7;-RM1& &1A& before making any connections 2@,$4 5se suitable gloves 2+,/4 C=7;-RM1& &1A& and identify cables before commencing "ork 2@,$4 7EA ;ollo" Standard Working Procedures 2Chapter @4 5se tools appropriately 23,@4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT ) INSTALLATION O> POWER AND LIG.T CA(LING WMS No3 01= Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 1WP Certificate, /, 7o previous e.perience re:uired, +, 1WP training if using 1WP, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS +999 and client<s specifications =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Po&!a-,e drills, ladders, appropriate mechanical handling e:uipment, Ma%n!enan+e C0e+/s) Mechanical handling e:uipment to be checked in accordance "ith Statutory and manufacturer<s re:uirements, %and tools and ladders to be checked daily, 1WP in accordance "ith manufactureIs recommendations, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement INSTALLTION O> POWER POINTS WMS No 01? Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check layout to dra"ings and specifications and confirm client, ), Check "alls, cavities and ceilings for other services and confirm location of any "ater pipes, gas lines or po"er or telephone cables, +, Check e:uipment is tagged, /, ;it po"er point mounting brackets as re:uired, 3, 0ape or insulate ends of ne" cable to prevent electrical contact, @, Run cables, >, Connect po"er points, C, Confirm fittings are secure and installed to specifications D, Clear area and remove -solation or &A781R 0A8S, 7EA ;alls %and in*uries 1lectric shock &ebris and noise from drilling 1lectric shock %and in*uries 1lectric shock 1lectric shock ;alling %and in*uries 7EA ) + $ + $ + $ $ ) + 7EA 1nsure area is clear 2$,34 Wear safety foot"ear, 2+,/4 5se suitable gloves 2+,/4 5se ladders in accordance "ith WMS 99@ 23,+4 5se fall protection as appropriate 2+,34 5se only correctly tagged e:uipment, 2/,)4 5se minimum drilling speed consistent "ith effective "ork, 5se appropriate respirators, eye and hearing protection 2+,/4 Aeep drill bits sharp, 5se ladder or platform appropriately, 23,+4 5se suitable insulating material 5se suitable gloves 2+,/4 Confirm &1A& before commencing "ork 2@,$4 Confirm &1A& before commencing "ork 2@,$4 5se ladder or platform appropriately, 23,+4 5se suitable gloves 2+,/4 RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT ) INSTALLATION O> POWER POINTS WMS No3 01? Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o +omp,e!e Bo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor,
$, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified electrical Supervisor by the &epartment of ;air 0rading, +, 7o previous e.perience re:uired, +, 1WP 0raining if using 1WP Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) AS+999 and clients specifications, =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Portable drill, pipe detection e:uipment, leads and ladders, Ma%n!enan+e C0e+/s) %and tools and ladders to be checked daily,
Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement
MANUAL .ANDLING WMS No 01@ Page 1 of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
2d4 0he ob*ect, %eights, space, chairs, lighting, floors, and access, Sufficient, ne", ages, disabilities, PP1 J C, training, ha'ard a"areness, -f team lifting, training and physically matched, Posture, bending, stretching, reaching, t"isting, and handling techni:ues, Si'e, shape, "eight, bulk, stability, hot, cold, sharp edges, grip, accurate placement, ) ) ) ) Complete Risk -dentification as in Appendi. ), Complete Risk -dentification as in Appendi. ), Complete Risk -dentification as in Appendi. ), Complete Risk -dentification as in Appendi. ), RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement
MANUAL .ANDLING WMS No 01@ Page # of # Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 +, Control ha'ards using the %ierarchy of Control and measures developed from $ and ), Personal in*uries and property damage, ) ;ormulate action plans to include What is to done, Who "ill be responsible for completion, When "ill the "ork be completed, and Monitoring and revie"ing the outcomes, RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement WOR5ING WIT. (OOM .OISTS WMS No 01A Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, Check that machine is safe to use mechanically, ), Check electrical e:uipment on machine, +, Check surfaces on "hich the machine is to be used, /, Secure "orking area, 3, Prevent falls, @, Check services in "ork area, Machine failure, personal in*ury 1lectric shock Machine instability Personal in*uries Personal in*uries Personal in*uries ) $ ) ) ) ) Check logbook, hydraulics, tyres, audile alarm, and "arning lights Check general purpose outlet, residual current device and earth continuity bet"een earth pin and machine frame, 0rip test RC&, 5se machine only on stable, level surfaces in accordance "ith the manufactures instructions, ?arricade "orking area, erect signs, tie tools on, and secure ob*ects left at height, 5se parachute harness "ith lanyard and shock absorber, 1nsure attachment point is appropriate, Stay "holly "ithin the bucket at all times, 1nter or e.it bucket only "hile lo"ered, 5se the machine only in "ind less than $),3 mEsec -solate as re:uired, RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT) WOR5ING WIT. (OOM .OISTS WMS 01A Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, =perators to hold appropriate Certificates of Competency, /, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) ?oom hoists to be checked in accordance "ith the manufactureIs instructions, Ma%n!enan+e C0e+/s) Maintenance to be carried out in accordance "ith the manufactureIs schedule, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement
USING MO(ILE SCA>>OLDS WMS No 020 Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, 1rect scaffold in accordance "ith the manufactures or supplier<s instructions, ), Check surfaces on "hich the scaffold is to be used, /, Secure "orking area,
3, =bserve safe "ork procedures, @, Check services in "ork area, 5nstable ground, =verturning, Collapse, ;alling, 1lectric shock, Scaffold instability, Personal in*uries, Personal in*uries,
Personal in*uries, ) $ ) ) )
) Place appropriate sole boards under standards, 1nsure handrails are fitted as erection proceeds, 5se fall protection as appropriate, 1nsure safe distances are maintained from conductors, 5se scaffold only on stable, level surfaces in accordance "ith the manufacture<s instructions, ?arricade "orking area, erect signs, tie tools on, and secure ob*ects left at height, Wear appropriate personal protective e:uipment, Stay "holly "ithin the scaffold at all times, 5se appropriate fall protection, 1nsure SWL is observed and "heels are locked "hen in "orking position, 5se the scaffold only in "ind less than $),3 mEsec, -solate as re:uired, RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: USING MO(ILE SCA>>OLDS WMS 020 Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 1rectors to hold appropriate Certificates of Competency, /, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Scaffolds to be checked in accordance "ith the manufactureIs instructions, Ma%n!enan+e C0e+/s) Maintenance to be carried out in accordance "ith the manufactureIs schedule, Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement
DISMANTLING MO(ILE SCA>>OLDS WMS No 021 Page 1 of 2 Isse Da!e 1"#"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage& C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona, Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 $, &ismantle scaffold in accordance "ith the manufacture or supplier<s instructions, )3 Secure "orking area, ;alling ob*ects, 1lectric shock, =verturning, Personal in*ury, Personal in*ury, ) $ ) ) ) 1nsure "ork platform is clean prior to dismantling, 1nsure safe distances are maintained from conductors, Remove lo"er ties only "hen the scaffold is dismantled do"n to that level, Wear appropriate personal protective e:uipment, 1nsure ropes for lo"ering e:uipment are securely tied, ?arricade "orking area and erect signs, RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable WORK METHOD STATEMENT: DISMANTLING MO(ILE SCA>>OLDS WMS 021 Page 2 of 2 Pe&sona, 7a,%f%+a!%ons an' E8pe&%en+e Pe&sonne,, D!%es an' Respons%-%,%!%es T&a%n%ng Re9%&e' !o Comp,e!e Wo&/ $, Minimum of trades assistant or apprentice "orking under a :ualified Supervisor, $, Supervisor to carry out daily inspections of "ork site for ha'ards, $, Supervisor to be trained in ha'ard identification, risk assessment and control, ), Appropriate industry induction, ), All personnel to maintain a tidy "ork site, ), Supervisor to be certified as a :ualified 1lectrical Supervisor by the &epartment of ;air 0rading, +, 1rectors to hold appropriate Certificates of Competency, /, 7o previous e.perience re:uired, Eng%nee&%ng De!a%,s"Ce&!%f%+a!es"Wo&/Co$e& App&o$a,s) Co'es of P&a+!%+e, Leg%s,a!%on) =ccupational %ealth and Safety Act )999, =%S Regulation )99$ and Code of Practice, 1lectrical Practices for Construction Work, P,an!"E9%pmen!) Ma%n!enan+e C0e+/s) Rea' an' S%gne' -y A,, Emp,oyees on S%!e) Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement (OSTI5 SOL6ENT CEMENT T:PE DNE >AST WMS No 002# Page 1 Isse Da!e 1"10"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y ) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage&) C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 /, ?rush applied solvent based a'0es%$e for unplasticised pvc pipe and fittings, 3, 0hin blue or clear li:uid "ith solvent odour, %armful by inhalation, %ighly flammable, -rritation due to skin and eye contact, %a'ardous to environment ) $ + + + 1nsure ade:uate ventilation, 5se respiratory protection K organic vapour cartridge mask or air supplied system, Aeep a"ay from sources of ingnition Kno smoking, 5se suitable 2solvent resistant4 gloves, 5se safety goggles if risk of eye contact e.ists, Avoid contaminating drains and "aterF"ays, RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement >LOURO SPOT MAR5ING PAINT WMS No 0022 Page 1 Isse Da!e 1"10"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y ) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage&) C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 Aerosol marking paint for spot marking of surfaces, %ighly ;lammable, %armful by inhalation, ) ) Aeep a"ay from sources of ignition K no smoking RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement SILICONE F INDUSTRIAL GRADE WMS No 002= Page 1 Isse Da!e 1"10"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y ) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage&) C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 Coloured or translucent nonFflo"ing paste "ith o.ime odour, %armful by inhalation, ) 1nsure ade:uate ventilation, RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement SLIPR: LOO( WMS No 002< Page 1 Isse Da!e 1"10"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y ) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage&) C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 Cable pulling lubricant 2thick yello" emulsion K odourless4, Minimal 7EA RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable Company Name REEDS ELECTRICAL SERVICES PTY LTD Work Method Statement GINC IT WMS No 002; Page 1 Isse Da!e 1"10"2002 Re$%s%on Da!e Re$%s%on No P&epa&e' (y ) Ma!! Ree' P&o*e+!) A,, S%!es App,%+a-,e Se+!%on P&o*e+! Manage&) C,%en! D%s!&%-!%on C,%en! O.S Company Pe&sona,
Wo&/ Me!0o' Des+&%p!%on R%s/ Assessmen! R%s/ Le$e,s Re+ommen'e' A+!%ons 1 2C,ase No34 Aerosol Spray Paint Spray earth bond -rritation J burning to eyes, %armful by inhalation, %ighly flammable, $ ) $ 5se safety goggles, 5se respiratory protection, Aeep a"ay from sources of ignition, RIS5 LE6ELS) CLASS 1 2.IG.4 CLASS 2 2MEDUIM4 CLASS # 2LOW4 6 0o be read in con*unction "ith 71CA Safety 8uide for 1lectrical -ndustry 1mployees )99$ 2Clause 7o,4 "here applicable