Professional Documents
Culture Documents
DGC A Paper 2 Sample Questions
DGC A Paper 2 Sample Questions
(8) I) Body hammers are used for driving stakes into the ground II) Sledge hammers are
used for smoothing or stretching the metal
a) Only I) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
(9) I) Claw hammers are basically used for driving and pulling out II) The wedge of a
cross peen hammer is parallel to the handle
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
(10) A punch is used to
a) Mark a location
b) Remove a damaged rivet
c) Locate a drill properly
d) AM are correct
(11) i) A pin punch is used to remove the shank of the rivet from the hole after rivet head
has been chiselled off ii) Diameter of pin punch should be 1/64 inch smaller than the
diameter of the rivet to be removed
a) Only I) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
(12) i) Location given by a prick punch should always be punched later with a centre
punch. ii) Goggles must be used while using any type of punch.
a) Only i) is correct
b) Only ii) is correct
c) Both I) and ii) are correct
d) Neither i) nor ii) is correct
(13) . I) A mushroom head on a punch is better than a crown head since chances of
hammer slip are reduced II) A centre punch can be used for a variety of punching
applications
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither I) nor ii) is correct
(14)Most commonly used slip joint plier has a length of
a) 4 inches
b) 6 inches
c) 10 inches d) 12 inches
(30) The part of a file that fits into the handle is called
a) Single cut r
b) Smooth cut
c) Rasp Both a) & b)
d) All are correct answers
(31) I) File is basically a chisel but with many cutting edges ii) Triangular files are used
for cutting teeth of handsaws
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither I) nor ii) is correct
(32)Double cut files have rows of teeth. These teeth are set at
a) 45 degrees and 70-80 degrees
b) 45 degrees and 45 degrees
c) 70-80 degrees and 70-80 degrees
d) None of these
(33) There are five cuts of files ranging from coarsest to the finest. Find out the wrong
one
a) Coarse
b) Bastard
c) Smooth
d) Finest
(34) File should be kept clean by
a) Tapping it against the bench
b) Brushing it with a wire brush
c) Lubricating it occasionally
d) Both a) & b) are correct
(35) Which type of file has only three grades: regular, fine and smooth
a) Vixen
b) Wood rasp
c) Knife
d) Triangular
(36) Characteristics of steel are controlled by
a) Removal of carbon from iron
b) Types of alloying elements added to it
c) Amount of alloying elements added to it
d) All are correct
(37) Bearing strength of a material refers to
a) Direct tensile load it can bear
b) Resistance to tear at the point of applied load
c) Watt
d) Coulomb
(60) Transfer of electrical energy from one conductor to another without the aid of
electrical connection is
a) Induction
b) Air gap transfer
c) Not poss
d) Possible but will cause excessive arcing thus not practical
(61) Magnetic lines of force pass most readily through
a) Aluminum
b) Copper
c) Iron
d) Titanium
(62) In a straight conductor, the resistance is not affected by
a) Length
b) Temperature
c) Shape of cross section
d) Material
(63) Pitot pressure varies with
a) Speed
b) Air density
c) Speed and Air density
d) None of these
(64) Altimeter and rate of climb indicator utilize
a) Static pressure
b) Pitot pressure
c) Either a) or b)
d) Both a) and b)
(65)Pitot static system have heating elements to
a) Remove moisture from the air
b) Prevent ice formation
c) To permit flying at high altitude
d) All are correct
(66) Pressure heads of pitot static system should not be painted, because it
a) Impairs their thermal efficiency
b) May cause obstruction of orifices
c) None of the above
c) Tension
d) None
(99) A cross inside triangle indicates
a) Close tolerance bolt
b) Corrosion resistant steel bolt
c) Stainless steel bolt
d) Screw
(100) A/C screw is generally manufactured with
a) Class-1 fit of thread
b) Class-2 fit of thread
c) Class-3 fit of thread
d) Class-4 fit of thread