Professional Documents
Culture Documents
5.500in 0.361wall IEU S135 HT55 (7.125 X 3.875 TJ) 10P 15B - 2 PDF
5.500in 0.361wall IEU S135 HT55 (7.125 X 3.875 TJ) 10P 15B - 2 PDF
Pipe Body
OD (in)
Wall Thickness (in)
Nominal ID (in)
Calculated Plain End Weight (lbs/ft)
New
(Nominal)
5.500
0.361
4.778
19.814
95% RBW
5.464
0.343
4.778
18.757
90% RBW
5.428
0.325
4.778
17.707
Premium
5.356
0.289
4.778
15.628
786,800
91,300
73,000
15,507
12,679
744,800
86,300
69,100
16,836
11,409
703,200
81,400
65,100
15,950
10,122
620,600
71,800
57,400
14,177
7,496
New
(Nominal)
5.828
23.758
17.930
7.031
14.062
API
Premium
4.597
22.527
17.930
5.527
11.054
Notes: Pipe Properties are calculated based on uniform OD and wall thickness
New = 100% RBW. Premium = 80% RBW
Burst Pressure for New based on 87.5% RBW per API
OD (in)
ID (in)
7.125
3.875
10.0
15.0
26.51
32.0
85,100
51,100
42,500
0.41
0.88
0.021
1,077,000
0.93
1.19
7.005
6.539
3.750
5.688
Box OD (in)
Elevator Capacity (lbs)
Smooth Edge
Height
N/A
N/A
5.812
Nominal
TJ OD
7.125
1,468,300
(without IPC)
0.89
0.021
Notes: The Drill Pipe Assembly adjusted weight, capacity and displacement calculations account for the adjusted ID in the manufacture of
95% RBW guaranteed pipe with 0.009" internal plastic coating. These values may vary with actual values due to pipe body mill
tolerances, internal plastic coating tolerances, and other factors.
New pipe guaranteed to 95% RBW will have a smaller ID (4.72'') than new pipe guaranteed to 87.5% RBW
Worn to min TJ OD
for API Premium
6.539
775,900
Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100 psi
A raised elevator OD increases elevator capacity without affecting make-up torque
The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy
and suitability of use of the technical information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall
thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end
user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per
Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
JCT 03-21-2011
TorqueTensionGraph
Connection:HT55(7.125(in)ODX3.875(in)ID)SMYS=120,000(psi)
PipeBody:80%InspectionClass,5.500(in)OD,0.361(in)wallthickness,S135PipeGrade
(safetyfactor=1.0)
1,600,000
PipeBodyinCombinedLoading
PipeBodyYieldat80%
InspectionClass
1,400,000
ConnectionPerformance(basedonMUT)
ToolJointYield
1,200,000
ToolJointShoulderSeparation
TJOperationalLimit(RecMUT)
Tenssion(lbs)
1,000,000
TJOperationalLimit(MinMUT)
800,000
600,000
400,000
200,000
Torque(ftlbs)
ConnectionWearforHT55(7.125(in)ODX3.875(in)ID)
MaterialSMYS(specifiedminimumyieldstrength)=120,000(psi)
90,000
80,000
70,000
Connection
60,000
T
Torque(ftlbs)
TorsionalStrength
RecommendedMUT
50,000
MinimumMUT
40,000
PipeBody
80% ofPremiumPipe
BodyTorsionalStrength
30,000
PipeBody:5.500(in)OD,0.361(in)wall
thickness,S135PipeGrade
20,000
10,000
ToolJointOD(in)