Professional Documents
Culture Documents
2000 Nissan Frontier KA24DE CL
2000 Nissan Frontier KA24DE CL
SECTION
CL
GI
MA
EM
LC
CONTENTS
PRECAUTIONS AND PREPARATION............................2
Precautions ..................................................................2
Special Service Tools ..................................................2
Commercial Service Tools ...........................................2
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING .....................................................3
NVH Troubleshooting Chart.........................................3
CLUTCH SYSTEM...........................................................4
Clutch Pedal ................................................................5
INSPECTION AND ADJUSTMENT .................................6
Adjusting Clutch Pedal ................................................6
Air Bleeding Procedure................................................7
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
SBR686C
Description
ST20630000
(J26366)
Clutch aligning bar
NT405
ST20050240
( )
Diaphragm spring
adjusting wrench
NT404
Description
a: 10 mm (0.39 in)
NT223
Bearing puller
NT077
Bearing drift
NT474
CL-2
SUSPECTED PARTS
(Possible cause)
Clutch grabs/chatters
1
1
2
3
4
CL-3
FA
5
5
5
5
2
2
2
2
2
5
5
6
3
6
4
7
FLYWHEEL (Distortion)
1
2
2
Clutch slips
CLUTCH LINE (Air in line)
CL-14
CL-14
CL-14
CL-14
CL-13
CL-13
CL-13
CL-13
CL-13
CL-13
CL-13
CL-13
CL-10
Refer to EM section
CL-9
CL-8
CL-7
CL-6
Reference page
Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspection. If necessary, repair or replace these parts.
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
RA
BR
ST
RS
BT
HA
EL
IDX
CLUTCH SYSTEM
ACL096
CL-4
CLUTCH SYSTEM
GI
Clutch Pedal
MA
EM
LC
EC
FE
CL
MT
AT
TF
ACL093
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
CL-5
2.
Free play due to clevis pin and clevis pin hole, push rod
and master cylinder.
Make sure that clevis pin can rotate smoothly.
If not, readjust pedal free play with master cylinder push rod.
ACL075
3.
ACL076
CL-6
EM
LC
EC
FE
CL
MT
ACL078
SCL203
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
CL-7
ACL097
INSPECTION
Check the following items, and replace as necessary.
CL-8
Operating Cylinder
MA
EM
LC
EC
FE
CL
MT
AT
TF
ACL090
PD
INSPECTION
Check the following items, and replace as necessary.
FA
BR
ST
RS
BT
HA
EL
IDX
CL-9
ACL091
CL145
SCL705
CL-10
GI
MA
EM
LC
SCL217
EC
INSPECTION
CL
MT
AT
LUBRICATION
PD
FA
RA
SCL752
BR
ST
RS
BT
HA
EL
IDX
CL-11
ACL094
CL-12
PD
FA
Clutch Disc
INSPECTION
RA
BR
RS
ACL063
BT
HA
EL
IDX
ACL064
CL-13
SCL466
FLYWHEEL INSPECTION
CAUTION:
Do not allow any magnetic materials to contact the ring gear
teeth.
Inspect contact surface of flywheel for slight burns or discoloration. Clean flywheel using emery paper.
INSTALLATION
Insert Tool into clutch disc hub while installing clutch cover and
disc.
Be careful not to allow grease to contaminate clutch facing.
Tighten bolts in numerical order, in two steps.
First step:
: 10 - 20 Nzm (1.0 - 2.0 kg-m, 7 - 14 ft-lb)
Final step:
: 22 - 29 Nzm (2.2 - 3.0 kg-m, 16 - 22 ft-lb)
ACL079
CL-14
General Specifications
CLUTCH CONTROL SYSTEM
CLUTCH DISC
Unit: mm (in)
Hydraulic
15.87 (5/8)
Model
240
Engine
KA24DE
Facing size
(Outer dia. x inner dia. x thickness)
EM
MA
LC
EC
CLUTCH COVER
17.46 (11/16)
FE
Model
240
Engine
KA24DE
Set-load
2WD
4WD
MT
CLUTCH DISC
Unit: mm (in)
Pedal height H*
Pedal free play A
(at pedal pad)
Clearance C between pedal
stopper bracket and clutch pedal
position switch (with clutch pedal
fully depressed)
Unit: mm (in)
Model
0.3 (0.012)
1.0 (0.039)
AT
240
CL
N (kg, lb)
115 (4.53)
TF
PD
1.0 (0.039)
FA
RA
CLUTCH COVER
Unit: mm (in)
Model
Diaphragm spring height
Uneven limit of diaphragm spring
toe height
240
BR
37.5 - 39.5
(1.476 - 1.555)
0.7 (0.028)
ST
RS
BT
HA
EL
IDX
CL-15
NOTES
CL-16