Professional Documents
Culture Documents
2a PDF
2a PDF
Product-Information
General
The well-known ETA-pump on the bearing bracket C and D is
constructed in accordance with DIN 24 255 standard and
completes the performance range up to max. 1800 m3/hr
(6600 Imp.g.p.m., 7900 USgpm). The graduation of pump sizes
enables you to select a model of high efficiency and low
absorbed horsepower under any set of operating conditions.
Field of Application
General water supplies for municipalities, industry and
agriculture; water works, pressure boosting and irrigation plants;
circulation of hot water, cooling water and oil; as condensate,
building sites, and loading pumps etc.
Nozzle Orientations
Suction nozzle axial, discharge nozzle radially pointing upward;
on sizes 200-23, 250-29 and 300-35 tangentially left pointing
upward. Other nozzle positions possible upon request.
Flanges machined according to DIN 2533, NP 16, from size
200 upward according to DIN 2532, NP 10.
Design
Horizontal single and two stage centrifugal pump with volute
casing flanged onto the bearing bracket. Sizes 100-50/2 and
125-50/2 are two-stage. Overhung radial flow impeller equipped
with balance holes for hydraulic balancing. Renewable casing
wear rings and shaft protecting sleeves.
Bearings
Axial and radial location by two oil lubricated deep groove ball
bearings in the bearing pedestal. Grease lubrication on request.
Shaft Seal
Drive
Direct drive by an electric motor, an internal combustion engine
or a turbine via a flexible coupling.
ETA C and D
Materials of constuction
Part No.
101
109
122/122a
211
202/202a
350.1
451
452
524
Part Designation
Volute Casting
Diffuser
Wear ring
Pump Shaft
Impeller
Shaft seal
Bearing housing
Stuffing housing box
Gland
Shaft Protecting sleeve
(01)
(02)
JL 1040
GCuSn 10
080M40Q
GCuSn 10
JL1040
Material combinations
(04)
(05)
JL 1040
JL 1040
JL 1040
GCuSn 10
431S29
JL 1040
GCuSn 10
(03)
Packed gland
Mechanical
(06)
(07)
JL1040
(08)
GCuSn 10
080M40Q 431S29
GCuSn 10
JL1040
Packed gland
Mechanical
JL 1040
JL 1040
JL 1040
JL 1040
316 SS
JL 1040
GG-25
Selection Charts
Selection chart at 1450 r.p.m.
200
300
200
100
400
300
500
400
US gpm 1000
Imp gpm
500
2000
1000
3000
2000
4000
3000
5000
4000
5000
300
H
m
100-50/2
125-50/2
150-50
200-50
200
250-50
50
125-40
100-40
40
ft
150-40
200-40
250-40
100
30
125-33
150-33
200-33
250-33
20
300-35
50
150-26
40
250-29
10
30
200-23
20
5
4
30
40
50
100
Q m3/h
200
300
400
500
1000
2000
ETA C and D
Dimension Table ETA - B:
Size
Bearing
Pump Dimensions
Shaft (pump)
Pedestal
b1
b2
so
dms
200 - 33
895
560
700
28
200
928
475
175
92
85
400
650
85
335
380
28
190
250
50
135
14
53.5
200 - 50
DS
900
660
800
33
200
933
575
175
92
85
400
650
85
335
380
28
190
250
50
135
14
53.5
ETA C and D
1151:37/5
439 432 241 XVI 407 433 447 101 202 344 102a
12.7.2005
Designation
Volute casing
Suction cover
Diffuser
Bearing pedestal
Joint ring
Joint ring
O ring
Shaft
Impeller
Impeller,1st stage
Spacer sleeve
Shaft protecting sleeve
Impeller nut
Lock washer
Thrower
Cooling cover
Gasket
Flat gasket
Stuffing box gland
Deep groove ball bearing
Joint ring
Joint ring
Bearing end cover
Bearing end cover
Felt ring
Stuffing box packing
O-ring
Gasket
Gasket
Gasket
Lantern ring
Felt ring cover
Cover
Rotating seal ring for casing
Washer
Stationary seal ring
Right handed spring
Set ring
Threaded plug/Sealing liquid
Cooling water / lnlet
Cooling water / Outlet
Leakage drain
Sealing liquid / lnlet
Oil dipstick
Sealing liquid channel
456
426
439
409
201
115 426a 432 241 XVI 433 101 447 109 124 202a 222
Part No.
101
102a
109
115
122
122 a
124
201
202
202 a
211
213
217
222
241
301
344
400.3
407
409
412.3
412.4
426
426a
432
433
434
437
438
439
447
456
471
472
474
475
478
500.3
556
IX
X
XVI
XX
f
c