Professional Documents
Culture Documents
Hilti KB3 PDF
Hilti KB3 PDF
1-800-879-8000 US www.us.hilti.com
1-800-363-4458 Canada www.ca.hilti.com
1
Anchoring Systems
Guide Specifications
Anchor: Expansion anchors shall be Kwik
Bolt 3 (KB3) supplied by Hilti, Inc. meeting the
description in Federal Specification A-A
1923A, Type 4 and shall bear a length
identification mark visible after installation.
Anchor bodies shall be manufactured to meet
one of the following conditions: 1. The carbon
steel electroplated anchor coating shall
conform to ASTM B633 with a minimum
thickness of 5m. 2. The carbon steel hot
dipped galvanized anchor body, nut and
washer coating shall conform to ASTM A 153,
Class C. The expansion sleeve conforms to
AISI 316. 3. Anchor body, nut and washer
conform to AISI 304. The expansion sleeve
conforms to AISI 316. 4. Anchor body, nut,
washer and expansion sleeve conform to AISI
316.
Kwik Bolt 3
Product Features
1.1
Product Description
1.2
Material Specification
1.3
Technical Data
1.4
Installation Instructions
1.5
Ordering Information
Installation
Drill hole in concrete, structural lightweight
concrete, or grout filled concrete block using a
Hilti carbide tipped drill bit and a Hilti rotary
hammer drill. Remove dust from the hole with
oil free compressed air. Alternately for 1/2,
5/8, 3/4, and 1 inch diameter Kwik Bolt 3
anchors, the hole may be drilled using a
matched tolerance Hilti DD-B or DD-C wet
diamond core bit for anchoring applications.
The slurry must be flushed from the diamond
cored hole prior to anchor installation. The
minimum hole depth must exceed the anchor
embedment prior to torquing by one hole
diameter. Drive the anchor into the hole using
a hammer. A minimum of six threads must be
below the surface of the fixture. Tighten the
nut to the recommended installation torque.
Impact Section
(Dog Point)
Nut
Washer
Anchor
Thread
Anchor
Body
Expansion
Sleeve
(Wedges)
Expansion Cone
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
Anchoring Systems
1.2 Material Specification
Carbon steel with electroplated zinc
All Carbon Steel Kwik Bolt 3, Long Thread Kwik Bolt 3 and Rod Coupling Anchors, excluding the 3/4 x 12 and 1 inch diameter
sizes, have the following minimum tensile bolt fracture loads:
Anchor Diameter
Fracture Load min.
1/4
2900 lbs
All 3/4 x 12, 1 inch diameter sizes and countersunk Kwik Bolt anchors
3/8
7200 lbs
1/2
12400 lbs
Anchor Diameter
Tensile Strength
Yield Strength
5/8
19600 lbs
5/8
105 ksi min.
90 ksi min.
3/4
88 ksi min.
75 ksi min.
Anchor Diameter
Fracture Load min.
1/4
2900 lbs
3/8
7200 lbs
3/4
28700 lbs
1/2
12400 lbs
3/4
28700 lbs
5/8
21900 lbs
Anchor Diameter
< 5/8
3/4
Anchor bodies 3/4" and larger and all stainless steel countersunk
Tensile Strength
90 ksi min.
76 ksi min.
Kwik Bolt series are produced from AISI 304 or 316 stainless
Yield Strength
76 ksi min.
64 ksi min.
steel having minimum mechanical properties:
Nuts meet the dimensional requirements of ASTM F 594.
Washers meet the dimensional requirements of ANSI B18.22.1, Type A, plain.
Expansion Sleeve for AISI 304 and 316 anchors are made from AISI 316, all nuts and washers for AISI 304 and 316
anchors are manufactured from AISI 304 and 316, respectively.
Refer to Kwik Bolt 3 Specification table under Section 1.3, for a listing
and specification of anchor specific and installation variables.
See Kwik Bolt 3 anchor product line table under Section 1.5 for full list
of anchor length ( ) and thread length ( th ) configurations.
Nd
N rec
V
+ d
V rec
1 .0
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
1
Anchoring Systems
in.
(mm)
1/4
(6.4)
3/8
(9.5)
1/2
(12.7)
in.
1/4
3/8
1/2
in.
1 1/8
1 5/8
2 1/2
3 1/2
2 1/4
3 1/2
4 3/4
(mm)
in.
(mm)
(29)
1 3/8
(35)
(51)
2 1/4
(57)
(76)
3 1/4
(83)
(41)
2
(51)
(64)
2 7/8
(73)
(89)
3 7/8
(98)
(57)
2 3/4
(70)
(89)
4
(102)
(121)
5 1/4
(133)
in.
(mm)
Normal
Carbon Steel ft-lb
Tinst
weight and
Zinc / HDG (Nm)
Recommended Lightweight
ft-lb
Stainless
installation concrete
(Nm)
Steel
torque
Grout filled
ft-lb
Carbon
Block
(Nm)
Steel
h
Min. base material thickness
in.
dh
5/16
(8)
4
(5.4)
6
(8.1)
4
(5.4)
7/16
(11)
20
(27)
20
(27)
15
(20)
3 in. (76mm) or 1.3 hef, whichever is greater
9/16
(14)
40
(54)
40
(54)
25
(34)
in.
(mm)
5/8
(15.9)
3/4
(19.1)
1
(25.4)
in.
5/8
3/4
Bolt Size
Details
2
dbit
in.
(mm)
in.
(mm)
in.
dh
wedge clearance hole in plate
(mm)
Tinst
Normal
Carbon Steel ft-lb
weight and
Zinc / HDG (Nm)
Recommended Lightweight
ft-lb
Stainless
installation concrete
(Nm)
Steel
torque
Grout filled
ft-lb
Carbon
Block
(Nm)
Steel
h
Min. base material thickness
in.
1
2
2 3/4
(70)
3 3/8
(86)
4
(102)
4 5/8
(117)
11/16
(17)
85
(115)
85
(115)
65
(88)
1
3
4 1/2
6
4 3/4 6 1/2
(165) (114)
(152)
(121)
6 4/5 5 1/2
5 1/2
7
(173) (140)
(140)
(178)
1 1/8
13/16
(29)
(21)
250
150
(339)
(203)
235
150
(319)
(203)
120
(163)
3 in. (76mm) or 1.3 hef, whichever is greater
5 1/2
(140)
6 1/8
(156)
3 1/4
(83)
4
(102)
See Kwik Bolt 3 anchor product line table under section 1.5 for full list of anchor length ( ) and thread length (
th
9
(229)
10
(254)
) configurations.
Loads for Kwik Bolt 3 are applicable for both carbide drill bits (see section 8.4.1 of 2005 Hilti Product Technical Guide)
and matched tolerance Hilti DD-B or DD-C diamond core bits in sizes ranging from 1/2 inch to 1inch .
Deep embedment depth for stainless steel Kwik Bolt 3 anchor is 8 inch (203 mm).
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
Anchoring Systems
1
1/4
(6.4)
3/8
(9.5)
1/2
(12.7)
5/8
(15.9)
3/4
(19.1)
1
(25.4)
Embedment
depth
in. (mm)
1 1/8
(29)
2
(51)
3
(76)
1 5/8
(41)
2 1/2
(64)
3 1/2
(89)
2 1/4
(57)
3 1/2
(89)
4 3/4
(121)
2 3/4
(70)
4
(102)
5 1/2
(140)
3 1/4
(83)
4 3/4
(121)
6 1/2
(165)
4 1/2
(114)
6
(152)
9
(229)
Tension
lb
(kN)
300
(1.3)
635
(2.8)
755
(3.4)
730
(3.2)
1260
(5.6)
1580
(7)
1235
(5.5)
1930
(8.6)
2135
(9.5)
1920
(8.5)
2660
(11.8)
3285
(14.6)
2120
(9.4)
3240
(14.4)
4535
(20.2)
3330
(14.8)
4930
(21.9)
6670
(29.7)
Shear
lb
(kN)
530
(2.4)
1135
(5)
3
1460
(6.5)
2235
(9.9)
5
3020
(13.4)
3800
(16.9)
48854
(21.7)
4090
(18.2)
5340
(23.8)
7070
(31.4)
9200
(40.9)
Tension
lb
(kN)
365
(1.6)
715
(3.2)
795
(3.5)
910
(4)
1555
(6.9)
1770
(7.9)
1430
(6.4)
2185
(9.7)
2355
(10.5)
2065
(9.2)
3020
(13.4)
3695
(16.4)
2425
(10.8)
4260
(18.9)
5860
(26.1)
4050
(18)
6000
(26.7)
7670
(34.1)
Shear
lb
(kN)
530
(2.4)
1275
(5.7)
3
1460
(6.5)
2485
(11.1)
5
3020
(13.4)
3935
(17.5)
48854
(21.7)
4900
(21.8)
5340
(23.8)
7600
(33.8)
9200
(40.9)
Tension
lb
(kN)
430
(1.9)
800
(3.6)
840
(3.7)
1095
(4.9)
1850
(8.2)
1965
(8.7)
1620
(7.2)
2440
(10.9)
2575
(11.5)
2210
(9.8)
3385
(15.1)
4100
(18.2)
2730
(12.1)
5285
(23.5)
7185
(32)
4670
(20.8)
7070
(31.4)
8670
(38.6)
Shear
lb
(kN)
530
(2.4)
1420
(6.3)
3
1460
(6.5)
2735
(12.2)
5
3020
(13.4)
4070
(18.1)
48854
(21.7)
5710
(25.4)
73255
(32.6)
8140
(36.2)
9200
(40.9)
Tension
lb
(kN)
550
(2.4)
845
(3.8)
1090
(4.8)
2060
(9.2)
2150
(9.6)
1975
(8.8)
3240
(14.4)
3620
(16.1)
2830
(12.6)
4770
(21.2)
5325
(23.7)
3785
(16.8)
6155
(27.4)
7005
(31.2)
5070
(22.6)
8400
(37.4)
10670
(47.5)
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
Shear2
lb
(kN)
530
(2.4)
1460
(6.5)
30205
(13.4)
48854
(21.7)
5710
(25.4)
73255
(32.6)
9200
(40.9)
1
Anchoring Systems
1/4
(6.4)
3/8
(9.5)
1/2
(12.7)
5/8
(15.9)
3/4
(19.1)
1
(25.4)
Embedment
depth
in. (mm)
1 1/8
(29)
2
(51)
3
(76)
1 5/8
(41)
2 1/2
(64)
3 1/2
(89)
2 1/4
(57)
3 1/2
(89)
4 3/4
(121)
2 3/4
(70)
4
(102)
5 1/2
(140)
3 1/4
(83)
4 3/4
(121)
6 1/2
(165)
4 1/2
(114)
6
(152)
9
(229)
Tension
lb
(kN)
1120
(5)
2375
(10.6)
2830
(12.6)
2740
(12.2)
4720
(21)
5925
(26.4)
4635
(20.6)
7240
(32.2)
8000
(35.6)
7210
(32.1)
9975
(44.4)
12315
(54.8)
7955
(35.4)
12150
(54)
17000
(75.6)
12500
(55.6)
18500
(82.3)
25000
(111.2)
Shear
lb
(kN)
1995
(8.9)
4250
(18.9)
54753
(24.4)
8380
(37.3)
5
11330
(50.4)
14250
(63.4)
4
18315
(81.5)
15335
(68.2)
20030
(89.1)
26500
(117.9)
34500
(153.5)
Tension
lb
(kN)
1370
(6.1)
2690
(12)
2990
(13.3)
3420
(15.2)
5830
(25.9)
6645
(29.6)
5355
(23.8)
8195
(36.5)
8830
(39.3)
7750
(34.5)
11335
(50.4)
13850
(61.6)
9100
(40.5)
15985
(71.1)
21970
(97.7)
15200
(67.6)
22500
(100.1)
28750
(127.9)
Shear
lb
(kN)
1995
(8.9)
4790
(21.3)
54753
(24.4)
9320
(41.5)
5
11330
(50.4)
14760
(65.7)
4
18315
(81.5)
18375
(81.7)
20030
(89.1)
28500
(126.8)
34500
(153.5)
Tension
lb
(kN)
1615
(7.2)
3000
(13.3)
3150
(14)
4100
(18.2)
6935
(30.8)
7365
(32.8)
6075
(27)
9145
(40.7)
9655
(42.9)
8285
(36.9)
12690
(56.4)
15385
(68.4)
10245
(45.6)
19820
(88.2)
26935
(119.8)
17500
(77.8)
26500
(117.9)
32500
(144.6)
Shear
lb
(kN)
1995
(8.9)
Tension
lb
(kN)
2060
(9.2)
3165
(14.1)
5328
(23.7)
54753
(24.4)
10260
(45.6)
5
11330
(50.4)
15265
(67.9)
4
18315
(81.5)
21410
(95.2)
5
27475
(122.2)
30500
(135.7)
34500
(153.5)
4095
(18.2)
7730
(34.4)
8055
(35.8)
7410
(33)
12140
(54)
13585
(60.4)
10615
(47.2)
17890
(79.6)
19970
(88.8)
14185
(63.1)
23085
(102.7)
26260
(116.8)
19000
(84.5)
31500
(140.1)
40000
(177.9)
Shear2
lb
(kN)
1995
(8.9)
54753
(24.4)
11330
(50.4)
18315
(81.5)
21410
(95.2)
5
27475
(122.2)
34500
(153.5)
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
Anchoring Systems
1
1/4
(6.4)
3/8
(9.5)
1/2
(12.7)
5/8
(15.9)
3/4
(19.1)
1
(25.4)
Embedment
depth
in. (mm)
1 1/8
(29)
2
(51)
3
(76)
1 5/8
(41)
2 1/2
(64)
3 1/2
(89)
2 1/4
(57)
3 1/2
(89)
4 3/4
(121)
2 3/4
(70)
4
(102)
5 1/2
(140)
3 1/4
(83)
4 3/4
(121)
8
(203)
4 1/2
(114)
6
(152)
9
(229)
Tension
lb
(kN)
260
(1.2)
540
(2.4)
685
(3)
605
(2.7)
1285
(5.7)
1620
(7.2)
1015
(4.5)
1445
(6.4)
1990
(8.9)
1650
(7.3)
2455
(10.9)
3480
(15.5)
1550
(6.9)
2510
(11.2)
2930
(13)
3120
(13.9)
4400
(19.6)
5600
(24.9)
Shear
lb
(kN)
595
(2.6)
675
(3)
880
(3.9)
1655
(7.4)
1875
(8.3)
3155
(14)
2875
(12.8)
4870
(21.7)
2880
(12.8)
5535
(24.6)
6080
(27)
7470
(33.2)
Tension
lb
(kN)
320
(1.4)
625
(2.8)
750
(3.3)
670
(3)
1430
(6.4)
1755
(7.8)
1230
(5.5)
1975
(8.8)
2250
(10)
1755
(7.8)
2900
(12.9)
3885
(17.3)
1950
(8.7)
3250
(14.5)
3870
(17.2)
3870
(17.2)
6400
(28.5)
8000
(35.6)
Shear
lb
(kN)
675
(3)
1110
(4.9)
1655
(7.4)
2130
(9.5)
3155
(14)
3485
(15.5)
4870
(21.7)
4260
(18.9)
5535
(24.6)
6770
(30.1)
7470
(33.2)
Tension
lb
(kN)
380
(1.7)
705
(3.1)
810
(3.6)
730
(3.2)
1575
(7)
1885
(8.4)
1450
(6.4)
2510
(11.2)
2510
(11.2)
1860
(8.3)
3340
(14.9)
4290
(19.1)
2350
(10.5)
3870
(17.2)
4530
(20.2)
4610
(20.5)
7200
(32)
9390
(41.8)
Shear
lb
(kN)
675
(3)
1345
(6)
3
1870
(8.3)
2380
(10.6)
3155
(14)
4095
(18.2)
4870
(21.7)
5645
(25.1)
7470
(33.2)
Tension
lb
(kN)
470
(2.1)
910
(4)
910
(4)
950
(4.2)
1940
(8.6)
2035
(9.1)
1620
(7.2)
2655
(11.8)
2985
(13.3)
2335
(10.4)
4395
(19.5)
6260
(27.8)
2610
(11.6)
4670
(20.8)
5120
(22.8)
4800
(21.4)
7330
(32.6)
9390
(41.8)
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
Shear2
lb
(kN)
675
(3)
1690
(7.5)
18703
(8.3)
2740
(12.2)
3155
(14)
4870
(21.7)
5645
(25.1)
7470
(33.2)
1
Anchoring Systems
1
1/4
(6.4)
3/8
(9.5)
1/2
(12.7)
5/8
(15.9)
3/4
(19.1)
1
(25.4)
Embedment
depth
in. (mm)
1 1/8
(29)
2
(51)
3
(76)
1 5/8
(41)
2 1/2
(64)
3 1/2
(89)
2 1/4
(57)
3 1/2
(89)
4 3/4
(121)
2 3/4
(70)
4
(102)
5 1/2
(140)
3 1/4
(83)
4 3/4
(121)
8
(203)
4 1/2
(114)
6
(152)
9
(229)
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
Anchoring Systems
1,2
1/2
(12.7)
5/8
(15.9)
3/4
(19.1)
1
2
Embedment
depth
in. (mm)
2 1/4
(57)
3 1/2
(89)
4 3/4
(121)
2 3/4
(70)
4
(102)
5 1/2
(140)
3 1/4
(83)
4 3/4
(121)
6 1/2
(165)
Intermediate load values for other concrete strengths and embedments can be calculated by linear interpolation.
Values shown are for shear plane acting through anchor threads.
1/2
(12.7)
5/8
(15.9)
3/4
(19.1)
Embedment
depth
in. (mm)
2 1/4
(57)
3 1/2
(89)
4 3/4
(121)
2 3/4
(70)
4
(102)
5 1/2
(140)
3 1/4
(83)
4 3/4
(121)
6 1/2
(165)
Intermediate load values for other concrete strengths and embedments can be calculated by linear interpolation.
Values shown are for shear plane acting through anchor threads.
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
1
Anchoring Systems
Anchor depth
in.
(mm)
1 1/8
(29)
2
(51)
1 5/8
(41)
2 1/2
(64)
2 1/4
(57)
3 1/2
(89)
2 3/4
(70)
4
(102)
3 1/4
(83)
4 3/4
(121)
Values shown are for shear plane acting through anchor threads.
Intermediate load values for other concrete strengths and embedments can be calculated by linear interpolation.
Anchor depth
in.
(mm)
1 1/8
(29)
2
(51)
1 5/8
(41)
2 1/2
(64)
2 1/4
(57)
3 1/2
(89)
2 3/4
(70)
4
(102)
Values shown are for shear plane acting through anchor threads.
Intermediate load values for other concrete strengths and embedments can be calculated by linear interpolation.
(12.7)
Min Depth of
Embedment
in.
3
3
4 1/2
(mm)
(76)
(76)
(114)
Tension
lb
955
930
1285
(kN)
(4.2)
(4.1)
(5.7)
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
Anchoring Systems
Carbon Steel and Stainless Steel Kwik Bolt 3 Allowable Loads Installed in
Lower Flute of Metal Profile Deck into Lightweight Concrete 1
Anchor Material
Carbon Steel
Stainless Steel
1
Anchor
Diameter
in.
(mm)
1/4
(6.4)
3/8
(9.5)
1/2
(12.7)
5/8
(15.9)
1/4
(6.4)
3/8
(9.5)
1/2
(12.7)
5/8
(15.9)
Min Depth of
Embedment
in.
(mm)
2
(51)
2 1/2
(64)
3 1/2
(89)
4
(102)
2
(51)
2 1/2
(64)
3 1/2
(89)
4
(102)
Anchor
Diameter
in.
(mm)
1/4
(6.4)
3/8
(9.5)
1/4
(6.4)
3/8
(9.5)
Min Depth of
Embedment
in.
(mm)
1 1/8
(29)
1 5/8
(41)
1 1/8
(29)
1 5/8
(41)
Shear values acting thru threads of anchor bolt. If acting through the empty shell, reduce loads by 70%
10
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
1
Anchoring Systems
3/8
(9.5)
1/2
(12.7)
5/8
(15.9)
3/4
(19.1)
Anchor Depth
in.
(mm)
1 1/8
(29)
(51)
1 5/8
(41)
2 1/2
(64)
2 1/4
(57)
3 1/2
(89)
2 3/4
(70)
(102)
3 1/4
(83)
4 3/4
(121)
Tension
Shear
lb
(kN)
lb
(kN)
150
(0.7)
380
(1.7)
540
(2.4)
445
(2)
320
340
(1.4)
(1.5)
780
(3.5)
630
665
(2.8)
(3)
905
(4)
815
865
1240
1295
(3.6)
(3.8)
(5.5)
(5.8)
1035
(4.6)
1645
1710
(7.3)
(7.6)
735
940
1010
1395
830
1465
1080
2375
890
2165
970
2770
785
3135
825
3305
(3.3)
(4.2)
(4.5)
(6.2)
(3.7)
(6.5)
(4.8)
(10.6)
(4)
(9.6)
(4.3)
(12.3)
(3.5)
(13.9)
(3.7)
(14.7)
Values are for anchors installed in Type 1 Grade N, lightweight, medium-weight, or normal-weight concrete
masonry units conforming to UBC Standard 21-4. The masonry units must be fully grouted with coarse grout
conforming to UBC Standard 21-15, Type S, N, or M. Masonry prism compressive strength must be at least
1500 psi at the time of installation when tested in accordance with UBC Standard 21-17.
2
Anchors must be installed a minimum of 1 3/8 inch from any vertical mortar joint (see figure).
3
Anchor locations are limited to one per masonry cell.
4
Embedment depth is measured from the outside face of the concrete masonry unit.
5
Linear interpolation to determine load values at intermediate edge distances is permitted.
6
All allowable loads based on safety factor of 4.0
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
11
Anchoring Systems
Carbon Steel Kwik Bolt 3 Allowable Loads for Anchors Installed in
Grout
V1
(mm)
in.
(76)
3
3 1/2 (89)
Parallel to
Wall (V1)
(kN)
(2.9)
(3.8)
lb
615
615
Shear
Perpendicular To
Wall (V2)
lb
310
310
(kN)
(2.7)
(2.7)
V2
(kN)
(1.4)
(1.4)
Min. 1 3/4"
See footnotes 1,2,3,4,6 for Kwik Bolt 3 anchors installed in grout filled concrete masonry unit.
Min. 4"
Minimum
Depth of
Embedment
in. (mm)
in.
(mm)
(6.4)
1/4
1 7/16 (37)
1
Lightweight Concrete
Shear
Tension
Shear
lb
(kN)
lb
(kN)
lb
(kN)
lb
(kN)
545
(2.4)
430
(1.9)
545
(2.4)
430
(1.9)
Lightweight Concrete
over Metal Deck
Tension
Tension
Upper flute
Lower flute
lb
(kN)
lb
(kN)
405
(1.8)
355
(1.6)
K
6
L
7
M
7
N
8
O
8
P
9
Q R S
9 10 11
T
12
10
13
Length
Identification Mark
12
c1
h
V
t
c2
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
11 12
1
Anchoring Systems
Adjustment
Conditions
Emb. Ratio
1.5
Reduction
c/he = 1.75
fRN = 1.00
0.75
he = hact
c/he
1.25
0.5
0.25
0
0.6
0.7
0.8
0.9
fRN
Adjustment Conditions
Shear Plane
Correlation
2.5
fRV1
c/hmin
fRV3
fRV2
1.5
1
Shear Condition
fRV1
fRV1 = 0.50
fRV2
fRV3
fRV2 = 0.60
fRV3 = 0.83
0.5
0
0.3
0.4
0.5
0.6
0.7
0.8
0.9
fRV
c/hmin = 3.00
c/hmin = 1.50
s/he
Adjustment
Conditions
Emb. Ratio
2.25
2
1.75
1.5
1.25
1
0.75
0.5
0.25
0
0.2
0.4
0.6
fAN
0.8
s/he
0.8
0.85
0.9
fAV
0.95
Reduction
s/he = 2.25
fAN = 1.00
he = hact
he = hnom
for the following condition
hact > hnom
hact = Actual Embedment
s = Actual Anchor Spacing Distance
fAN = Anchor Spacing Reduction Factor for Tension Loading
Adjustment
Conditions
Emb. Ratio
Reduction
2.25
2
1.75
1.5
1.25
1
0.75
0.5
0.25
0
he = hact
hmin hact hnom
for the following condition
he = hnom for the following condition
hact > hnom
hact = Actual Embedment
s = Actual Anchor Spacing Distance
fAV = Anchor Spacing Reduction Factor for Shear Loading
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
13
Anchoring Systems
Emb. in.
1 1/8
1 11/16
1 3/4
2
2
3
3
4
4
2
1/4
1/2
3
3/8
1/2
4
1/2
3/4
5
0.85
0.92
0.99
1.00
1.24
1.28
1.42
1.56
1.63
1.70
0.60
0.64
0.68
0.76
0.82
0.84
0.92
1.00
1.04
1.08
1 1/8
0.80
0.93
0.95
2
0.68
0.76
0.77
1 1/8
0.90
0.94
0.94
1.00
1.07
1.13
1.24
1.33
1.36
1.48
1.60
1.66
1.72
0.80
0.83
0.87
0.93
0.98
1.00
1.07
1.13
1.17
1.20
0.96
0.98
1.00
1.03
1.06
1.07
1.10
1.14
1.16
1.18
0.90
0.91
0.92
0.94
0.96
0.96
0.98
1.00
1.01
1.02
1 1/8
0.33
0.50
0.52
0.59
0.67
0.74
0.89
1.00
1.04
1.19
1.33
1.41
1.48
1 1/8
0.47
0.60
0.61
0.67
0.73
0.79
0.91
1.00
1.03
1.15
1.27
1.33
1.39
1 1/8
0.83
0.84
0.86
0.89
0.91
0.96
1.00
1.01
1.06
1.11
1.14
1.16
Spacing
3/8 in.
Tension
fAN
Emb. in.
1 5/8
2
2 1/4
2 1/2
3
3 1/4
3 1/2
3 3/4
4
4 1/2
5
5 5/8
5 3/4
Anchor
Diameter
1/2 in.
Emb. in.
2 1/4
2 1/2
3
3 3/8
3 3/4
4 1/4
4 3/4
5
5 3/4
6
6 1/2
7 1/4
7 3/4
14
1 5/8
0.60
0.67
0.72
0.77
0.87
0.92
0.97
1.00
1.07
1.17
1.26
1.39
1.41
Edge
Distance
Tension
fRN
Spacing
Shear
fAV
1 5/8 2 1/2
0.90
0.92
0.93
0.94
0.97
0.98
0.99
1.00
1.02
1.04
1.07
1.10
1.10
0.90
0.92
0.92
0.93
0.94
0.95
0.96
0.98
1.00
1.00
0.51
0.62
0.67
0.72
0.77
0.82
0.92
1.00
1.15
1.18
3/8
1/2
hdeep
hmin
3
1 5/8
hnom
hdeep
hmin
hnom
2 1/2
3 1/2
2 1/4
3 1/2
hdeep
4 3/4
NOTE:
Tables apply for listed embedment
depths. Reduction factors for other
embedment depths must be calculated
using equations below.
Spacing - Tension
hmin hact hnom
hact hnom
fRV2
1 5/8
0.61
0.69
0.73
0.77
0.82
0.86
0.94
1.00
1.12
1.14
fRV3
1 5/8
0.83
0.87
0.89
0.90
0.92
0.94
0.97
1.00
1.05
1.06
c
+ 0.88
f AN = hact
3.13
c
+ 0.88
f AN = hnom
3.13
f RN =
+2
h act
3 . 75
c
f RN =
+2
h nom
3 . 75
Spacing - Shear
hmin hact hnom
hact hnom
s
f AV =
+10.25
hact
12.5
s
f AV =
+10.25
hnom
12.5
c
3h min
f RV 1 =
c
Parallel to Edge
f RV 2 =
Perpendicular Away
from Edge
f RV 3 =
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
+ 0.75
hmin
3.75
+ 5.82
hmin
8.82
1
Anchoring Systems
2 3/4
0.60
Emb. in.
2 3/4
0.80
2 3/4
0.69
0.75
0.60
0.92
0.80
0.94
0.90
0.77
0.83
0.92
0.98
1.00
1.09
1.15
1.18
1.27
1.33
0.62
0.66
0.72
0.76
0.78
0.84
0.88
0.90
0.96
1.00
0.95
1.00
1.07
1.12
1.14
1.21
1.26
1.28
1.36
1.41
0.82
0.85
0.90
0.93
0.95
1.00
1.03
1.05
1.10
1.13
0.94
0.96
0.98
0.99
1.00
1.02
1.04
1.05
1.07
1.08
0.91
0.92
0.93
0.94
0.95
0.96
0.97
0.98
0.99
1.00
4
4
5
6
6
7
7
7
8
1/4
3/4
1/2
1/4
1/2
3/4
1/2
9
3/4 in.
Emb. in.
3 3/8
4
5
5 3/4
6 1/4
6 1/2
7
7 1/2
8 1/4
9
9 3/4
10 1/4
10 3/4
Anchor
Diameter
1 in.
Emb. Depth,
4 1/2
6
7
8
9
9 3/4
10 1/4
11 1/4
11 5/8
12 1/2
13
13 1/2
14 3/4
2 3/4
2 3/4
0.87
0.92
1
0.52
0.58
0.67
0.73
0.76
0.85
0.91
0.94
1.00
1.09
0.61
0.66
0.73
0.78
0.81
0.88
0.93
0.95
1.00
1.07
0.84
0.86
0.89
0.91
0.92
0.95
0.97
0.98
1.00
1.03
3 1/4 4 3/4
0.90
0.92
0.94 0.90
0.96 0.92
0.97 0.93
0.98 0.93
0.99 0.94
1.00 0.95
1.02 0.96
1.04 0.97
1.06 0.98
1.07 0.99
1.08 1.00
3 1/4
3 1/4
3 1/4
0.51
0.59
0.64
0.67
0.72
0.77
0.85
0.92
1.00
1.05
1.10
0.61
0.67
0.71
0.73
0.77
0.82
0.88
0.94
1.00
1.04
1.08
0.83
0.86
0.88
0.89
0.90
0.92
0.95
0.97
1.00
1.02
1.03
6
0.60
0.65
0.71
0.76
0.80
0.83
0.88
0.90
0.95
0.97
1.00
1.07
4 1/2
0.80
0.89
0.95
1.00
1.07
1.11
1.14
1.20
1.22
1.27
1.30
1.33
1.41
3/4
2 3/4
hmin
0.90
3 1/2
Anchor
Diameter
6
0.80
0.84
0.89
0.93
0.97
0.99
1.00
1.05
1.09
1.11
1.13
1.19
4 1/2
0.90
0.93
0.94
0.96
0.98
0.99
1.00
1.02
1.03
1.04
1.05
1.06
1.08
4 1/2
4 1/2
4 1/2
0.90
0.91
0.93
0.94
0.95
0.96
0.97
0.98
0.99
0.99
1.00
1.02
0.52
0.59
0.67
0.72
0.76
0.83
0.86
0.93
0.96
1.00
1.09
0.61
0.67
0.73
0.78
0.81
0.87
0.89
0.94
0.97
1.00
1.07
0.84
0.86
0.89
0.91
0.92
0.94
0.95
0.97
0.99
1.00
1.03
3 1/4
hnom
4 3/4
hdeep
6 1/21
hmin
4 1/2
hnom
hdeep
NOTE:
Tables apply for listed embedment
depths. Reduction factors for other
embedment depths must be clculated
using equations below.
Spacing - Tension
hmin hact hnom
hact hnom
c
+ 0.88
f AN = hact
3.13
c
+ 0.88
f AN = hnom
3.13
f RN =
+2
h act
3 . 75
c
f RN =
+2
h nom
3 . 75
Spacing - Shear
hact hnom
hmin hact hnom
s
s
+10.25
+10.25
hnom
hact
f
=
f AV =
AV
12.5
12.5
Edge Distance - Shear
hact hmin
Perpendicular
Toward Edge
c
3h min
f RV 1 =
c
Parallel to Edge
f RV 2 =
Perpendicular
Away from Edge
f RV 3 =
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
+ 0.75
hmin
3.75
+ 5.82
hmin
8.82
15
Anchoring Systems
1.4 Anchor Installation Instructions
Kwik Bolt 3 Anchor Installation Instructions into normal weight and
lightweight concrete
16
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
1
Anchoring Systems
1. Drill.
2. Clean.
5. Tap-in again
6. Tighten.
1. Drill.
2. Clean.
3. Tap-in.
4. Tighten.
1. Drill hole
using 1/4" bit.
2. Tap-in
3. Pry downward
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
17
Anchoring Systems
1.5 Ordering Information
Kwik Bolt 3 Anchor Product Line
Length ( )
Size
in. (mm)
1/4x1 3/4
1/4x2 1/4
1/4x3 1/4
1/4x4 1/2
3/8x2 1/4
1 3/4
2 1/4
3 1/4
4 1/2
2 1/4
(44)
(57)
(83)
(114)
(57)
3/8x3
(76)
3/8x3 3/4
3 3/4
(95)
3/8x5
(127)
3/8x7
1/2x2 3/4
7
2 3/4
(178)
(70)
1/2x3 3/4
3 3/4
(95)
1/2x4 1/2
4 1/2
(114)
1/2x5 1/2
5 1/2
(140)
1/2x7
5/8x3 3/4
7
3 3/4
(178)
(95)
5/8x4 3/4
4 3/4
(121)
5/8x6
(152)
5/8x7
(178)
5/8x8 1/2
5/8x10
8 1/2
10
(216)
(254)
3/4x4 3/4
3/4x5 1/2
3/4x7
18
Thread Length (
4 3/4
5 1/2
th
in. (mm)
3/4
(19)
2
3
7/8
1 1/8
1 1/2
1 1/8
2 1/2
1 1/8
3 1/4
5 1/2
(51)
(76)
(22)
(29)
(38)
(29)
(64)
(29)
(83)
(140)
1 1/4
(32)
2 1/4
1 1/4
3
1 1/4
3 3/4
4 3/4
(57)
(32)
(76)
(32)
(95)
(121)
1 1/2
(38)
2 1/2
1 1/2
4
1 1/2
4 3/4
6 1/2
7
(64)
(38)
(102)
(38)
(121)
(165)
(178)
1 5/8
(41)
2 1/2
(64)
1 5/8
(41)
3 3/8
(86)
1 5/8
4 1/2
5 3/4
(41)
(114)
(140)
3/4x8
(203)
3/4x10
3/4x12
1x6
1x9
1x12
10
12
6
9
12
(254)
(305)
(152)
(229)
(305)
ID
Stamp
A
B
D
G
B
(152)
2 1/4
(57)
(152)
50
L
C
E
25
I
L
E
G
J
15
L
O
R
(146)
100
10
20
10
20
10
20
10
20
L
N
R
T
J
P
T
Box
(121)
(178)
10
Carbon Steel
304 SS
316 SS
HDG
282502
282503
282504
282521
282505
282506
282522
282507
282523
282508
282524
282525
282509
282510
282526
282511
282527
282512
282528
282529
282513
282514
282530
282515
282531
282516
282532
282533
282534
282517
282535
282518
282536
282519
282537
282539
282540
282541
282553
282542
282543
282554
282544
282555
282545
282556
282557
282546
282547
282558
282548
282559
282549
282560
282561
282550
282551
282562
282552
282563
282564
286020
282565
282566
282567
282568
282569
282570
282571
282572
282573
282574
286033
286034
-
378083
378084
378085
378086
378087
378088
378089
378090
-
286021
286024
286025
286026
-
282520
286027
378091
282538
286016
286017
286018
286019
286028
286029
286030
286031
286032
286035
286036
-
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
1
Anchoring Systems
Length
in. (mm)
(51)
2
3
5
2 1/4
3
4
5
(76)
(127)
(57)
(76)
(102)
(127)
Box
Quantity
100
100
50
100
100
50
50
286039
286040
286041
286042
286043
Size
3/8x2 1/4
2 1/4
(57)
Thread Length
in. (mm)
7/8
ID
Stamp
Quantity
100
283470
(22)
Box
Length
Box
in. (mm)
Quantity
Carbon Steel
100
371389
(57)
US: 1-800-879-8000 / www.us.hilti.com | HILTI Product Technical Guide 2005 | Canada: 1-800-363-4458 / www.ca.hilti.com
19
Kwik Bolt 3
2005 Product Technical Guide
Supplement
NOTES:
1-800-879-8000 US www.us.hilti.com
1-800-363-4458 Canada www.ca.hilti.com
expertise. in every case.
P.O. Box 21148, Tulsa OK 74121 US 1-800-879-8000 www.us.hilti.com Canada 1-800-363-4458 www.ca.hilti.com Printed in the United States
Hilti is an equal opportunity employer Hilti is a registered trademark of Hilti, Corp. Copyright 2005 by Hilti, Inc. Rev 02/11/2005
The data contained in this literature was current as of the date of publication. Updated and changes may be made based on later testing.
is needed that the data is still current, please contact the Hilti Technical Support Specialist at 1-800-879-8000. All published load values contained
in this literature represents the results of testing by Hilti or test organizations. Local base materials were used. Because of variations in materials,
on site testing is necessary to determine performance at any specific site.