Professional Documents
Culture Documents
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
TABLE OF CONTENTS APRIL 2007
T A B L E
O F
C O N T E N T S
I N S TA L L AT I O N S E C T I O N
PART
1
DESCRIPTION
PRE-INSTALLATION INFORMATION
1.1
1.2
1.3
1.4
INSTALLING CABINETS
2.1
2.2
2.3
2.4
2.5
3.2
3.3
3.4
3.5
3.6
PAGE
CONNECTING POWER
5.1
5.2
Home Page
OfficeServ 7100
TECHNICAL MANUAL
10
Table of Contents
INSTALLATION
TABLE OF CONTENTS APRIL 2007
6.2
7.2
POWER UP PROCEDURES
8.1
8.2
8.3
9.2
FIGURES
Figure 2.1 Tools Required for Rack Installation
Figure 2.2 Rack Installation (1)
Figure 2.3 Rack Installation (2)
Figure 2.4 Rack Installation (3)
Figure 2.5 Required Tools for the installation on a Wall
Figure 2.6 Installation on a Wall (1)
Figure 2.7 Installation on a Wall (2)
Figure 2.8 Installation on a Wall (3)
Figure 2.9 Installation on a Wall (4)
Figure 2.10 Installation on a Wall (5)
Figure 2.11 Installation on a Wall (6)
Figure 2.12 Installation on a Wall (7)
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
TABLE OF CONTENTS APRIL 2007
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
TABLE OF CONTENTS APRIL 2007
Table of Contents
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
TABLE OF CONTENTS APRIL 2007
TABLES
Table 1.1 Power Specifications
Table 3.1 Card installation Configuration
Table 3.2 Parts on the Rear Panel of the Cabinet
Table 3.3 Ports and LEDs of the MP10 Card
Table 3.4 UNI card Ports and LEDs
Table 3.5 Ports and LEDs of the TEPRI/TEPRIa
Table 3.6 Ports and LEDs of the 8TRK Card
Table 3.7 Ports of the 16DLI2 Card
Table 3.8 Ports and LEDs of the 8DLI Card
Table 3.9 16MWSLI Card Ports
Table 3.10 Ports and LEDs of the 8SLI Card
Table 3.11:MGI16 Front Panel Components
Table 6.1 OfficeServ 7100 Line Conditions
Table 7.1 Distance Between Stations and the System
Table 7.2 Installation Tool Specification
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 1 APRIL 2007
The OfficeServ 7100 system should not be installed near materials that can cause a
fire, such as explosive gas and inflammables. The OfficeServ 7100 system should
not be near equipment that generate electromagnetic waves, such as monitors or
copying machines.
The installation location should be convenient for distributing trunk lines and
extension lines, for connecting power and grounding wires, and for maintenance
and repair.
The OfficeServ 7100 system should not be installed in aisles or passageways that
are populated or used for moving equipment.
Always maintain cleanliness to prevent dust from damaging the card connectors of
the cabinet.
Before installing the OfficeServ 7100 system, check items such as the electrical
wiring status, grounding status, voltage and frequency.
Do not expose equipment to direct sun light, corrosive fumes, and constant
vibrations.
Do not install in close proximity to a fire sprinkler or other sources of water.
A dedicated commercial AC power outlet is required. Do not use extension cords.
Ensure that all wires and cables to and from the OfficeServ 7100 do not cross
fluorescent lights or run in parallel with AC wires.
This equipment is to be installed only in restricted access areas (dedicated,
equipment closets, etc.) in accordance with articles 110-16, 110-17, 110-18 of the
National Electric Code, ANSI/NFPA 70.
1.1
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 1 APRIL 2007
1.2
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 1 APRIL 2007
1.3
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 1 APRIL 2007
Power Consumption
Specification
Input power
AC 110 V
DC 48V
(48VDC, 3A for battery backup ONLY)
Output power
- DC -54V, 1.1 A
- DC +5 V, 5.0 A
- DC -5.3 V, 0.3 A
- DC +3.3 V, 5 A
- DC +12 V, 0.4 A
- DC -54V, 0.25 A (for battery backup)
105 Watts
1.4
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
2.1
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
2.2
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
3) Align the two holes of the cabinet bracket and the holes of the rack brackets, and
fasten the cabinet to the rack with the two screws.
2.3
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
2.4
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
2) Make holes on the marked positions of the wall mount bracket. Make the depths
and the diameters of the holes more than 35 mm and around 5.5 mm such that the
plastic anchors can be inserted.
2.5
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
4)
Align the screw holes of the wall mount bracket to the position that the plastic
anchors are driven. Insert screws to each hole and tighten the screws with a Phillips
screw driver.
5) Two screws exist in the two screw holes among the four screw holes on the bottom
side of the OfficeServ 7100 cabinet. Unscrew the two screws to a height of about
2 mm.
2m
2.6
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
6) Tighten the mount locking screws into the remaining two holes among the four
screw holes on the bottom of the OfficeServ 7100 cabinet. At this point, do not
tighten completely, but keep the screws out about 2 mm.
7) Align the screws on the bottom of the OfficeServ 7100 cabinet to the bracket holes,
then pull down the cabinet to lock the cabinet securely.
2 mm
2.7
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 2 APRIL 2007
As shown in the figure below, connect an earth ground to the ground lug behind the
OfficeServ 7100.
2.8
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
Front
Slot 0
Slot 1
Slot 2
Rear
Cards Allowed
MP10 ONLY
3.1
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
Slot
Cards Allowed
NOTE: The OfficeServ 7100 only supports PRI service and does not support T1
service even though the TEPRI and TEPRIa cards support both.
The descriptions about each part on the rear of the cabinet are listed in the table below.
Table 3.2 Parts on the Rear Panel of the Cabinet
Part
Function
Power Switch
AC Power connector
AC LED
DC LED
Battery Socket
Ground Lug
3.2
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
S2
On
Off
S1
Off
On
Memory Backup Switch (S1): When set to ON, all system programming is saved in
SRAM even when system is rebooted or powered OFF. This will be saved in SRAM
until the Super Capacitor has been drained of all charge (this charge will last only
up to 24 hours with system power OFF). At that point all programming will be lost. It
is recommended that all programming is saved to the MMC+ card or to a PC using
the OfficeServ Installation Tool application. Turning the switch (S1) OFF will set the
system to DEFAULT. To default the system, keep this switch (S1) in the OFF
position for 30 seconds. Switch to ON position before powering up the system.
Note: The S2 dip switches are set properly by the factory for a 3 digit numbering
plan and the country of USA. These dip switches should be left at default and
should never be changed. If a 4 digit numbering plan is required the numbering
plan should be changed in the software by using MMC 724.
OFF (right)
SW8
SW7
SW6
SW5
SW4
SW3
SW2
SW 1
3.3
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Country
Korea
USA
UK
Italy
Australia
New Zealand
Holland
Denmark
Switch 5 reserved.
These DIP switches will not take effect unless the switches are set in the wanted
position and the system memory is cleared manually by using the Memory Backup
switch.
The MP10 board supports a 2-Wire Full Duplex modem board. This is the same
modem used on the OfficeServ 500 system.
The Modem board operates in OfficeServ 7100 via V.24 interface. In addition, the
Modem board supports V.90 protocol. OfficeServ 7100 controls the Modem board
via serial communication using standard AT commands. When mounting a modem
card, the holes on the corners of the modem should be aligned such that the
spacer fits in the hole in the following figure.
3.4
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
MODEM
The 4SWM (optional 4 port POE LAN module) or 4DLM (optional 4 port Digital Line
module) daughter cards can be mounted to connector P11, P12 and P13 of the MP10
card. A screw is installed to the support located next to connector P13. Remove this
screw, install the daughter card and install the screw to secure the card as shown
below.
4SWM
or
4DLM
3.5
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
2) Align the MP10 card to the guardrail of slot 0 and carefully slide it in.
3) Press and lock the lever to fully insert into the slot.
3.6
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 3 APRIL 2007
Table of Contents
Function Description
P1~P4 Ports
MISC Port
Media Card
Slot for installing the MMC+ media storage card. This card
contains the main system software, system configuration
database, and voicemail greetings and messages.
LAN Port
SIO port
RST button
RUN LED
LAN LED
3.7
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 3 APRIL 2007
Table of Contents
Function Description
This LED indicates the status of the MMC+ card access.
- Off: The MMC+ card is not installed.
- On: The MMC+ card is installed, however, is not being accessed.
- Blink: The MMC+ card is installed and is being accessed.
3.8
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
1) Turn off system power using the power switch in the back of the system.
3.9
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3) Align the new card to the guardrail of the slot, and slide the new card into the slot.
Then lock the lever in the front panel of the card to fully secure into the connector of
the OfficeServ 7100 main card.
3.10
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
4SLM
4TRM
3.11
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
The front view of the UNI card is shown in the picture below.
Function Description
MD1 P1~P4
MD2 P1~P4
MD3 P1~P4
MD (1~3) LEDs
3.12
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
port LAN Switch that receives/transmits data from/to Intranet or Internet. The 4SWM provides
four 10/100 BASE-T Ethernet ports and performs the Layer 2 Switching function. These four
ports support Power Over Ethernet (PoE) and are IEEE 802.3af compliant.
Power constraints must be taken into consideration when plugging ITP phones and
WAP devices into the 4SWM PoE module.
POWER CONSUMPTION
OS7100 Samsung Equivalent Power Units (SEPU)
Devices
Optional Power
iDCS Phones
n/a
DS 5000 Phones
n/a
ITP Phones
AC adapter or External
PoE Switch
AC adapter or External
PoE Switch
If you need more than 4 ethernet ports, you can uplink this to an external layer 2 data
switch providing additional ports.
3.13
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 3 APRIL 2007
Table of Contents
3.14
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3.15
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3.16
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3.17
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
NOTE: The OfficeServ 7100 only supports PRI and does not support
T1 service even though the TEPRI and TEPRIa cards support both.
The TEPRI/TEPRIa card can be installed in slots 1 and/or 2. The first four LEDs on the
front of the card provide the status of the service (Sync, AIS, Loss and Layer 2 Active
3.18
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
states). The second four LEDs on the front of the card display the type of service. The
first TEPRI/TEPRIa card installed in the OfficeServ 7100 is the primary source of
external clocking. The second TEPRI/TEPRIa installed is the secondary source of
external clocking. Default clock selection is left to right in the cabinet. The clock priority
can be changed by using MMC 826. Regardless of position, a CO PRI circuit should
always be given clocking priority over T1 circuits. There are two RJ45 modular jacks on
the face of the card. The settings for T1 or PRI service are selected by a bank of dip
switches as defined below. The PRI supports NI1, NI2, AT&T No. 5 ESS, and DMS 100
offices. A maximum of 2 TEPRI/TEPRIa cards can be provided per system. NOTE: Do
not insert this card with system power ON.
ON
OFF
T1
E1
PRI
T1
NFAS (24B)
NFAS (23B + D)
NETWORK*
USER
AFT
NORMAL
**
**
**
**
**
**
*If this TEPRI/TEPRIa card is to be the master of a pair of TEPRI/TEPRIa cards that are
used to connect two systems together via PRI networking then this DIP switch, DIP
switch 4 must be set to ON.
**Do not change the settings of DIP switches 3, 5, 6, 7, and 8. Switches 3, 5, 6, and 7
must remain OFF and 8 must be ON.
3.19
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
See the S1 switch and jumpers of the TEPRI/TEPRIa card as shown below.
1
1
1
J
J
1
1
J1
J2
SW1
On
SW8
Off
JUMPER SETTING
The TEPRI/TEPRIa card comes from the factory with the following jumper settings.
These settings should NOT be changed.
3.20
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
Function Description
T1/E1/PRI
SIO
RST
SYNC LED
Clock synchronization.
- On: Indicates loss of framing (Error Condition).
- Off: Clocks are synchronized when they inter-work with the counterpart
station (Normal).
LOS LED
AIS LED
This LED indicates whether the T1 remote alarm has been generated.
- On: The remote alarm has been generated. All ones are being received
(Error)
- Off: The remote alarm has not been generated (Normal).
L2 LED
3.21
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
Function Description
IPC LED
This LED indicates that this card is inter-working with the higher-level
module.
- On: The card is inter-working with the MP10.
- Off: The card is not inter-working with the MP10.
CLK LED
TP1 LED
TP2 LED
3.5.2 8TRK
The 8TRK card provides 8 ports for analog trunk lines with Caller ID capabilities. This
card can go into any universal slot (1 ~ 2). Add as many as needed.
3.22
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
The components on the front panel of the 8TRK have the functions below:
Table 3.6 Ports and LEDs of the 8TRK Card
Ports & LEDs
Function Description
P1~P8
Trunk ports.
P1~P8 LED
3.5.3 16DLI2
This card provides 16 ports for connecting Samung Digital Keysets. Each port provides
1B+D. This means only one station/one voice channel per port. This card can go into
slots 1 and/or 2. Add as many as needed.
Function Description
P1~P16
Refer to Section 7.1.3 (Connecting a Digital Phone) for port Pinout and Wiring.
3.23
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
SPECIFICATIONS
The specifications of the 8DLIcard are as follows:
8 station ports
NOTE: KDB-D or KDB-S adapters are not supported on the OfficeServ 7100 system.
Front panel components of the 8DLI card have the functions below:
Table 3.8 Ports and LEDs of the 8DLI Card
Ports
Function Description
P1~P8
P1~P8 LED
3.24
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3.5.5 8COMBO
This card provides 8 ports for connecting analog stations and 8 ports for connecting
Samsung Digital Key sets. This card can go into slots 1 and/or 2. Add as many as
needed.
3.5.6 16MWSLI
This card provides 16 ports for connecting analog stations. It can go into slots 1 and/or
2. Add as many as needed. This card automatically detects DTMF or dial pulse signals
from the SLT. This card has no DTMF receiver. It will share the system resources.
3.25
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
Function Description
Analog Extension Ports
The 16MWSLI supports Message Waiting Lamp functionality for analog stations that
have this capability.
Port 1 (Pins 7 & 8) supports Power Failure Transfer function (Refer to Section 3.4).
Do not connect devices with a total REN greater than 5.0 to this card.
3.26
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3.5.7 8SLI
This card provides 8 ports for connecting analog stations. It can go into slots 1 and/or 2.
Add as many as needed. This card automatically detects DTMF or dial pulse signals
from SLT. This card does not have any DTMF receivers; it uses system resources.
Function Description
P1~P8
P1~P8 LED
Port 1 (Pins 1 & 2) supports Power Failure Transfer function (Refer to Section 3.4).
Do not connect devices with a total REN greater than 5.0 to this card.
3.27
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3.5.8 MGI-16
The MGI-16 is a 16 channel Media Gateway Card. The MGI-16 card provides a variety
of Voice over IP (VoIP) services for the OfficeServ 7100. This card is used for ITP
phones, IP networking, IP trunking or any application that require VoIP functionality.
NOTE: The MP10 processor cards have 8 MGI channels built-in. However, these
channels have to be activated with the appropriate license key entered in mmc
841. Refer to the OfficeServ 7100 Programming Manual for details. The MGI16
does NOT require any licenses to operate.
SPECIFICATIONS
Function Description
LAN
SIO
RST
PWR LED
RUN LED
3.28
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
Function Description
LAN Tx LED
LAN Rx LED
SVC LED
DSP LED
RTPT LED
RTPR LED
HARDWARE CAPACITIES
Interface Card
Location
UNI card
Slots 1 & 2
4SWM
MP10 only
4DLM
4SLM
UNI card
4TRM
UNI card
8TRK
Slots 1 & 2
8COMBO
Slots 1 & 2
8SLI
Slots 1 & 2
8DLI
Slots 1 & 2
16DLI2
Slots 1 & 2
16MWSLI
Slots 1 & 2
TEPRIa
Slots 1 & 2
MGI16
Slots 1 & 2
3.29
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 3 APRIL 2007
3.30
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 4 APRIL 2007
To reduce risk of fire and injury, use only a sealed nickel cadmium or lead-acid
battery supply capable of handling a charge current of 0.25A, a charge voltage
of 54 V DC, and a discharge rate of 26 Ah.
Make sure the batteries you install conform to local building, fire and safety codes.
Some battery types emit hydrogen gas during the charging state and may require
venting to fresh air.
Do not place batteries directly on a concrete floor. This causes them to discharge
very quickly.
Follow the battery manufacturers recommended installation and maintenance
procedures.
4.1
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 4 APRIL 2007
2) Connect the white wire of the battery cable to the (+) terminal, and the black wire to
the (-) terminal of the battery. Connect the other end of the battery cable to the
external battery socket on the rear panel of the OfficeServ 7100 cabinet.
4.2
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 5 APRIL 2007
5.1
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 6 APRIL 2007
Wires with AWG #24 or AWG #26 width should be used as subscriber lines.
Never touch non-insulated telephone wires or terminals unless the telephone line
has been disconnected at the Network Interface.
When wiring cables in high-humidity areas, remove moisture before wiring.
Never install telephone jackets in a wet location unless the jack is specifically
designed for wet locations.
Wires should be handled carefully to prevent any changes or damages.
Subscriber lines should be kept indoors if possible.
High voltage power lines should not be wired near a subscriber line.
Never install telephone wiring during a lightening storm.
Leak resistance for C.O. lines connected to the OfficeServ 7100 system is as follows:
Table 6.1 OfficeServ 7100 Line Conditions
Line Condition
Leak Resistance
20 k or higher
20 k or higher
6.1
Table of Contents
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 6 APRIL 2007
Pin No.
Function
C.O.
C.O.
TIP
RING
T1/PRI Port
(RJ-45)
Pin No.
T1
Function
Rx+
Rx-
Tx+
Tx-
PRI
Function
Tx+
Tx-
Rx+
Rx-
6.2
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
The maximum distance between stations and the OfficeServ 7100 are as follows:
Table 7.1 Distance Between Stations and the System
Station
Distance
Digital phone
Analog phone
Door phone
AOM
7.1
Table of Contents
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 7 APRIL 2007
P1 port
Pin No.
Function
PFT TIP
PFT RING
SLI 1 TIP
SLI 1
RING
P2-P8 port
Pin No.
Function
SLI TIP
SLI RING
Function
SLI 1
TIP
SLI 1
RING
PFT
TIP
PFT
RING
P2-P16 Port
Pin No.
Function
SLI TIP
SLI
RING
7.2
Table of Contents
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 7 APRIL 2007
S1-S8 Port
Pin No.
Function
SLI TIP
SLI RING
Figure 7.3 RJ-45 Port of the 8COMBO Card (For Analog Phone)
Pin No.
Function
SLI TIP
SLI
RING
7.3
Table of Contents
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 7 APRIL 2007
Pin No.
Function
DLI TIP
DLI RING
Pin No.
Function
DLI TIP
DLI RING
Figure 7.6 RJ-45 Port of the 8DLI Card (For Digital Phone)
7.4
Table of Contents
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 7 APRIL 2007
Pin No.
Function
DLI TIP
DLI RING
Figure 7.7 RJ-45 Port of the 16DLI2 Card (For Digital Phone)
Pin No.
Function
DLI TIP
DLI RING
Figure 7.8 RJ-45 Port of the 8COMBO Card (For Digital Phone)
7.5
Table of Contents
Home Page
OfficeServ 7100
TECHNICAL MANUAL
INSTALLATION
PART 7 APRIL 2007
Pin No.
Function
Tx+
Tx-
Rx+
Rx-
Pin No.
Function
DLI TIP
DLI RING
Figure 7.10 RJ-45 Digital Ports of the cards mentioned above (For Door Phone Connection)
1) Connect the Door Box port of the DPIM to the Line port of the door phone.
2) When using an automatic door lock, connect the Lock port of the DPIM and the
door phone contact point to the door lock.
3) The door lock contact point is designed to control low-voltage relay and uses 24 VDC
and 100 mA. Do not attempt to connect commercial AC power to these contact.
7.6
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
MMC
MMC 211 is used to assign call numbers to door phones. Use MMC 501 to
program duration of contact closure. For detailed instruction on the MMC
program, refer to OfficeServ 7100 Programming Section.
SECURING
SCREWS
REMOVE
KNOCKOUTS
7.7
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
7.8
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
7.9
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
To secure the handset once you wall-mounted your keyset you must remove the
handset retaining clip reverse it such that the extended clip is facing the top of the
phone (see Figure 7.13).
BASE STAND SLOTS
SCREW HOLES
BASE STAND
HANDSET
RETAINING CLIP
IN WALL-MOUNTING
POSITION
HANDSET
RETAINING CLIP
IN DESKTOP
POSITION
G ITP-5107S Keysets
Figure 7.13 Wall-Mounting DS 5000, ITP-5121D and
7.10
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
7.11
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
REMOVE
KNOCKOUTS
7.12
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
DEFAULT DN
HARDWARE ITEM
371
MOH/BGM
02
361
03
362
Dry Contact
04
363
Dry Contact
05
3999
Internal Modem
PINS 4 and 5
7.13
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
MMC
Select music sources for C.O. lines in MMC 408 and music sources for
extensions in MMC 308. For detailed instructions on the MMC programs, refer
to OfficeServ 7100 Programming Manual.
The following ports are assigned to the external MOH inputs on the MIS daughter card:
HARDWARE
ITEM
MOH/BGM Ext. Source
MISC
FUNCTION # in MMC 724
01
DEFAULT
DN (Ports)
371
MISC
FUNCTION # in MMC
724
02
DEFAULT
DN (Ports)
Contact Pair #1
03
362
Contact Pair #2
04
363
7.14
361
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
Dry Contact
8
7
6
5
4
3
2
1
External 3
Page Equipment 6
(600 ohms)
8 Conductor
Plug
7
8
1
2
Dry Contact
5
4
MOH/BGM
MISC
Dry Contact
Dry Contact is a switch that can connect or cut the power or line to external
equipment.
DEFAULT
DN
362 or 363
Next connect the output MISC port to a customer provided paging system or other
suitable customer provided speaker, see Figure 7.18.
7.15
DEFAULT
DN
362 or 363
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
The OfficeServ 7100 system supports only one dry contact for the common bell. The
MISC port is located on the front panel of the MP10.
Dry contact
(For common bell)
DEFAULT
DN
361
7.16
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
Specification
Platform
IBM PC
CPU
OS
Main memory
64 Mbytes or higher
Hard disk
1 Gbytes or higher
7.17
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
Execute IS tool
Click [System] -> [Link Control] menu to set the communications link.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
7.18
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
Execute IS tool
Click [System] -> [Link Control] menu to set the communications link.
Enter System Name (eg; ABC Company).
Select the <link type> (eg; MODEM).
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
7.19
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
Note: Internal modem card must be installed for the connection to work. The incoming
telco line may need to be programmed to ring directly to modem port of OS 7100
system in MMC 406 (eg. Trunk 701 ring to port 3999).
7.20
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 7 APRIL 2007
MP
LAN
OfficeServ 7100
SMDR
MCP
LAN
OfficeServ 7100
Printer
7.21
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 8 APRIL 2007
8.1 PRE-CHECK
This section describes items to check before starting the OfficeServ 7100 system.
Temperature: Check if the temperature of the room where the system is installed is
between 32F and 113F. If the room temperature is higher or lower than the normal
operation temperature, install a heating/cooling device to maintain normal
temperature.
Humidity: Check if the room humidity where the system is installed is between
10 % and 90 %. Take special caution since humidity affects the electrical
components and connectors of the system.
Direct sunlight and dust: The room where the OfficeServ 7100 system is installed
should be protected from direct sunlight and should have ventilation systems to
prevent the system from malfunctioning due to dust.
Check if the OfficeServ 7100 system is not inclined and is maintained horizontally.
Do not place devices that may cause electromagnetic interference near the system.
Place a fire extinguisher near the system.
Check if the AC voltage switch of the PSU is properly set to 110 VAC power.
Check if the grounding terminal on the rear panel of the system is properly
connected to the external grounding.
Check if the cards and cables are properly mounted and connected to the
OfficeServ 7100 cabinet.
Make sure the MMC+ Card with system software is in the Media slot.
Make sure the memory backup switch on MP10 is in the ON position.
Turn on the power of the OfficeServ 7100 cabinet.
Check the LEDs of the MP10.
8.1
Home Page
OfficeServ 7100
TECHNICAL MANUAL
6)
Table of Contents
INSTALLATION
PART 8 APRIL 2007
The RUN LED of the MP10 card lights green and the MC LED flashes when the
system normally starts the booting process.
Once the booting is complete, the RUN LED of the MP10 card flashes green, and
the MC LED stops flashing and remains lit. (It takes approximately 2 to 3
minutes to boot up).
Enable MGI channels by entering the appropriate license key in system
programming (if MGI services are required).
7)
8)
9)
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 8 APRIL 2007
Six iDCS 28 button keyset are packaged with the OS7100 system and the line keys are
preset and pre-labeled to support the OS7100 default configuration. If the iDCS 18
button keysets are connected to the OS7100 system they will also come up preconfigured to support the default line key layout. Please see the following diagram for
the iDCS 28 and 18 button line key defaults.
8.3
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 8 APRIL 2007
Note: Other types of iDCS, DS and ITP phones can be connected however the line keys
will have a different default button configuration.
One the OfficeServ 7100 system is booted, the MP10 card verifies the cards mounted
on each slot and saves this information as the default configuration of the system. At
default, the OfficeServ 7100 system assigns 3 digits to Co lines, extensions, and
extension groups. Refer to Sections 3. Installing and Replacing cards of this manual
for details on switch 2.
CO line numbers from 701 through 7XX are sequentially assigned (by default) to the
first CO line card installed in the system from left to right and following numbers are
continuously assigned to the next CO line card of the next slot.
Extension numbers from 201 through 2XX are sequentially assigned to the first station
type card mounted in the system from left to right (starting from 4DLM if mounted on
the MP10) and following numbers are continuously assigned to the next extension card
of the next slot. This numbering process continues until the extension numbers are
assigned to all extensions.
8.4
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 8 APRIL 2007
The first 8 ports are assigned to the operator group as default. Group 500 with
members 201 through 208, and Voicemail Group 519 with members 301 through 304.
The numbering plan of CO lines, extensions, and extension groups can also be
changed in the database at any time using MMC 724 (STATION NUMBERING PLAN).
8.5
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 9 APRIL 2007
9.1
Home Page
OfficeServ 7100
TECHNICAL MANUAL
Table of Contents
INSTALLATION
PART 10 APRIL 2007
10.1