Professional Documents
Culture Documents
Ratiometric, Linear Hall-Effect Sensors: Features
Ratiometric, Linear Hall-Effect Sensors: Features
27501B*
3503
RATIOMETRIC, LINEAR
HALL-EFFECT SENSORS
The UGN3503LT, UGN3503U, and UGN3503UA Hall-effect
sensors accurately track extremely small changes in magnetic flux
densitychanges generally too small to operate Hall-effect switches.
OUTPUT
GROUND
CC
SUPPLY
Dwg. PH-006
FEATURES
Extremely Sensitive
Flat Response to 23 kHz
Low-Noise Output
4.5 V to 6 V Operation
Magnetically Optimized Package
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSORS
FUNCTIONAL BLOCK DIAGRAM
1 VCC
REG.
OUTPUT
GROUND
Dwg. FH-007
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Operating Voltage
VCC
4.5
6.0
Supply Current
ICC
9.0
13
mA
VOUT
B=0G
2.25
2.50
2.75
Sensitivity
VOUT
B = 0 G to 900 G
0.75
1.30
1.75
mV/G
23
kHz
90
50
220
BW
Vout
Output Resistance
ROUT
BW = 10 Hz to 10 kHz
All output-voltage measurements are made with a voltmeter having an input impedance of at least 10 k.
Magnetic flux density is measured at most sensitive area of device located 0.016" (0.41 mm) below the branded face of the U
package; 0.020" (0.51 mm) below the branded face of the UA package; and 0.030" (0.76 mm) below the branded face of the LT
package.
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSORS
OUTPUT VOLTAGE AS A
FUNCTION OF TEMPERATURE
OUTPUT NOISE AS A
FUNCTION OF FREQUENCY
4.0
10
VCC = 5V
3.5
OUTPUT IN VOLTS
B= +500G
3.0
B = 0G
2.5
2.0
8.0
VCC = +5V
TA = +25C
6.0
4.0
2.0
B= -500G
1.5
40
20
+25
+85
10
+125
AMBIENT TEMPERATURE IN C
SUPPLY CURRENT AS A
FUNCTION OF SUPPLY VOLTAGE
1K
10K
Dwg. A-12,505
DEVICE SENSITIVITY AS A
FUNCTION OF SUPPLY VOLTAGE
12
2.5
B = 0G
11
TA = +25C
SUPPLY CURRENT IN mA
100
FREQUENCY IN HZ
Dwg. A-12,573
10
9.0
TA = +25C
2.0
1.5
1.0
0.5
8.0
7.0
4.5
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
6.0
4.5
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
6.0
Dwg. A-12,506
Dwg. A-12,507
5.0
B = 0G
TA = +25C
4.0
3.0
2.0
1.0
OUTPUT SYMMETRY
99
98
W
ITY BELO
LINEAR
G
B = -900
NULL
LL
VE NU
ITY ABO
LINEAR
G
B = +900
97
TA = +25C
96
95
4.5
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
6.0
Dwg. A-12,508
4.5
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
6.0
Dwg.A-12,509
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSORS
OPERATION
NOTCH SENSOR
The south pole of a magnet is attached to the back of the package if the
Hall-effect IC is to sense the presence of ferrous material. The north pole of a
magnet is attached to the back surface if the integrated circuit is to sense the
absence of ferrous matrial.
Calibrated linear Hall devices, which can be used to determine the actual
flux density presented to the sensor in a particular application, are available.
SENSOR LOCATIONS
SUFFIX U
ACTIVE AREA DEPTH
0.015"
0.38 mm
0.093"
2.37 mm
NOM
3 2
0.072"
1.83 mm
1
Dwg. A-12,512
CURRENT MONITOR
BRANDED
SURFACE
Dwg. MH-002-5C
SUFFIX LT
ACTIVE AREA DEPTH
0.030"
0.76 mm
NOM
SUFFIX UA
ACTIVE AREA DEPTH
0.018"
0.46 mm
NOM
0.091"
2.32 mm
0.084"
2.13 mm
0.042"
1.08 mm
0.056"
1.43 mm
A
1
BRANDED
SURFACE
Dwg. A-12,513
Dwg. MH-008-9
Dwg. MH-011-3C
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSORS
UGN3503LT
(SOT-89/TO-243AA)
Dimensions in Inches
(for reference only)
0.173
0.181
0.064
0.072
0.155
0.167
0.055
0.063
Dimensions in Millimeters
(controlling dimensions)
0.090
0.102
0.014
0.017
0.084
0.090
3.94
4.25
0.014
0.019
0.017
0.022
0.035
0.047
0.059
4.40
4.60
1.62
1.83
1.40
1.60
2.29
2.60
0.35
0.44
2.13
2.29
0.36
0.48
0.89
1.20
0.44
0.56
1.50
BSC
BSC
3.00
0.118
BSC
BSC
Dwg. MA-009-3 in
2.5
2.0
0.098
0.079
B
0.031
A
Dwg. MA-009-3 mm
0.102
0.8
2.6
4.6
0.181
3 0.047
1.2
0.028
0.031
0.7
0.8
TYP
TYP
TYP
TYP
Dwg. MA-012-3 in
Dwg. MA-012-3 mm
NOTE:Exact body and lead configuration at vendors option within limits shown.
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSORS
UGN3503U
Dimensions in Inches
(controlling dimensions)
Dimensions in Millimeters
(for reference only)
0.183
0.178
4.65
4.52
1.60
1.50
0.063
0.059
4.60
4.47
0.181
0.176
45
45
0.086
0.018
2.18
0.46
MAX
MAX
0.600
0.560
0.015
15.24
14.23
0.38
0.41
0.016
SEE NOTE
SEE NOTE
1.27
0.050
0.100
2.54
Dwg. MH-003D in
Dwg. MH-003D mm
NOTES: 1. Tolerances on package height and width represent allowable mold offsets.
Dimensions given are measured at the widest point (parting line).
2. Exact body and lead configuration at vendors option within limits shown.
3. Height does not include mold gate flash.
4. Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm).
5. Minimum lead length was 0.500" (12.70 mm). If existing product to the original specifications is not acceptable,
contact sales office before ordering.
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSORS
UGN3503UA
Dimensions in Inches
(controlling dimensions)
Dimensions in Millimeters
(for reference only)
4.17
4.04
0.164
0.159
0.062
0.058
45
1.57
1.47
45
3.10
2.97
0.122
0.117
45
45
0.085
0.031
2.16
0.640
0.600
0.79
0.38
SEE NOTE
0.016
0.41
1.27
0.050
BSC
16.26
15.24
0.015
SEE NOTE
MAX
MAX
BSC
Dwg. MH-014D in
Dwg. MH-014D mm
NOTES: 1. Tolerances on package height and width represent allowable mold offsets.
Dimensions given are measured at the widest point (parting line).
2. Exact body and lead configuration at vendors option within limits shown.
3. Height does not include mold gate flash.
4. Minimum lead length was 0.500" (12.70 mm). If existing product to the original specifications is not acceptable,
contact sales office before ordering.
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSORS