Professional Documents
Culture Documents
Kyocera FS-1800, 3800 Service Manual
Kyocera FS-1800, 3800 Service Manual
FS-3800/N
Page printers
Notice
The information in this
manual is subject to change
without notification.
Additional pages may be
inserted in future editions. The
reader is asked to excuse any
technical inaccuracies or
typographical errors in the
present edition.
No responsibility is assumed
if accidents occur while the
service person is following the
instructions in this manual.
The contents of this manual
are protected by copyright. No
part of the manual may be
reproduced or copied by any
means without the permission
of the copyright holder.
Information
This equipment has been
tested and found to comply
with the limits for a Class A*1/
Class B *2 digital device,
pursuant to Part 15 of the FCC
Rules. These limits are
designed to provide
reasonable protection against
FS-1800/1800N | FS-3800/3800N
harmful interference in a
residential installation. This
equipment generates, uses,
and can radiate radio
frequency energy and, if not
installed and used in
accordance with the
instructions, may cause
harmful interference to radio
communications. However,
there is no guarantee that
interference will not occur in
a particular installation. If this
equipment does cause harmful
interference to radio or
television reception, which
can be determined by turning
the equipment off and on, the
user is encouraged to try to
correct the interference by one
or more of the following
measures.
Reorient or relocate the
receiving antenna.
Increase the separation
between the equipment and
receiver.
Connect the equipment into an
outlet on a circuit different
: FS-1800N/FS-3800N
*2
: FS-1800/FS-3800
Important notice to
service person
Before attempting service on
the equipment, including
disassembling, reassembling,
troubleshooting, and
adjustment, read this manual
carefully. During performing
service, use extreme care to
avoid possible electric shock
hazard, burn, and human
injuries. Make sure the printer
is not provided with any safety
facilities other than those
primarily intended for the
safety of users.
Regarding Tradenames
PRESCRIBE is a registered trademark of Kyocera Corporation.
PRESCRIBE 2e, KPDL, and KIR (Kyocera Image Refinement) are trademarks of Kyocera Corporation.
Diablo 630 is a product of Xerox Corporation.
IBM Proprinter X24E is a product of International Business Machines Corporation.
Epson LQ-850 is a product of Seiko Epson Corporation.
Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-Packard Company.
Centronics is a trade name of Centronics Data Computer Inc.
PostScript is a registered trademark of Adobe Systems Incorporated.
Macintosh is a registered trademark of Apple computer, Inc.
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
PowerPC and Micro-Drive are trademarks of International Business Machines Corporation.
CompactFlash is a trademark of SanDisk Corporation.
ENERGY STAR is a U.S. registered mark.
All other brand and product names are registered trademarks or trademarks of their respective companies.
This Kyocera page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL6 language emulation.
PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach, CA 90278, U.S.A.
This product was developed using the Tornado Real Time Operating System and Tools from Wind River Systems.
Contains UFST and MicroType from Agfa Corporation.
Fine 1200 mode uses iRET image enhancement technology.
iRET is a trademark of Oak Technology, Inc.
FS-1800/1800N | FS-3800/3800N
Conventions
Throughout this manual, the following conventions are used:
Italic letters refer related chapters or sections or documentations.
This symbol followed by WARNING denotes that the following paragraph(s) includes
precautions which, if ignored, could result in personal injury, and/or irrevocable
damage to the printer.
When followed by CAUTION this symbol denotes that the following paragraph(s)
include the precautions which, if ignored, could result in damage to the printer.
FS-1800/1800N | FS-3800/3800N
Chapter 1:
Product Information
Chapter 2:
Installation/Operation
Chapter 3:
Maintenance/Adjustments
Chapter 4:
Operation Overview
Chapter 5:
Disassembly
Chapter 6:
Troubleshooting
Contents
Appendix A: Diagrams
Appendix B: Status Page
Appendix C: Interface
Contents
Contents
FS-1800/1800N | FS-3800/3800N
REVISION HISTORY
Version
1.00A
1.10
1.20
Date
23-Oct-2000
4-Dec-2000
4-Jul-2001
Replaced Pages
1-7, 3-12, 3-14, 3-15,
3-16, 4-37, 5-12,
5-37, 6-11,6-15,
6-16, 6-17, 6-18,
6-19, 6-20, 6-21,
6-22,6-23, 6-24, B-4,
B-5
1-6, 1-7, 2-18,
2-20, 3-14, 3-15,
3-16, 3-19, 3-20
Remarks
TO OBTAIN THE LATEST PRINTER DRIVERS AND UTILITIES, VISIT US AT OUR INTERNET HOME
PAGE: http://www.kyocera.com/w2k
FS-1800/1800N | FS-3800/3800N
Chapter 1
Product Information
Chapter 1 Contents
1-1 Printer specifications ...................................................................................................................... 1-3
1-1-1 Specifications ............................................................................................................................ 1-3
(1) Engine ....................................................................................................................................... 1-3
(2) Controller ................................................................................................................................... 1-4
(3) Weight and dimensions ............................................................................................................. 1-4
(4) Power requirements .................................................................................................................. 1-5
(5) Environmental requirements ...................................................................................................... 1-5
1-1-2 Available option memory/device ................................................................................................ 1-6
(1) Expansion memory (DIMM) ....................................................................................................... 1-6
(2) Memory card (CompactFlash) ................................................................................................... 1-7
(3) Hard disk (Microdrive) ............................................................................................................... 1-8
1-2 Names of parts ................................................................................................................................. 1-9
1-2-1 Names of parts .......................................................................................................................... 1-9
1-3 Safety information ......................................................................................................................... 1-10
1-3-1 Safety information .................................................................................................................... 1-10
(1) Laser safety ............................................................................................................................. 1-10
(2) Laser notice ............................................................................................................................. 1-10
(3) Laser caution label on the scanner unit ................................................................................... 1-10
(4) CDRH regulations (U.S.A.) ...................................................................................................... 1-12
(5) Ozone concentration ............................................................................................................... 1-12
(6) FCC statement (U.S.A.) ........................................................................................................... 1-12
a) For the FS-1800 and FS-3800 models ..................................................................................... 1-12
b) For the FS-1800N and FS-3800N models ................................................................................ 1-13
(7) Canadian Department of Communications compliance statement .......................................... 1-13
(8) Avis de conformit aux normes du ministre des Communications du Canada ..................... 1-13
(9) ISO 7779 ................................................................................................................................. 1-13
(10) CE marking directive ............................................................................................................. 1-14
(11) Declaration of conformity (Australia) ..................................................................................... 1-14
1-4 Environmental requirements ........................................................................................................ 1-15
1-4-1 Environmental conditions ........................................................................................................ 1-15
(1) Clearance ................................................................................................................................ 1-16
(2) Places to avoid ........................................................................................................................ 1-17
(3) Note on power ......................................................................................................................... 1-17
(4) Removing the printer ............................................................................................................... 1-18
1-5 About the toner container ............................................................................................................. 1-19
1-5-1 Toner container ....................................................................................................................... 1-19
(1) Toner container handling ......................................................................................................... 1-19
(2) Toner container storage .......................................................................................................... 1-20
FS-1800/1800N
FS-3800/3800N
24 pages/min. (A4)
25 pages/min. (Letter)
FS-1800/1800N | FS-3800/3800N
1-3
(2) Controller
Item
CPU
System ROM
Font ROM
Main (Video) RAM
Maximum:
Slot:
DIMM size:
Memory card (Optional)
Hard disk (Optional)
Host interface
Parallel:
Serial:
Network interface card:
(KUIO-LV [3.3 V])
Page description language
Standard emulation modes
FS-1800/1800N
PowerPC405GF/200MHz
4 MB Mask (or Flash) DIMM
2 MB
FS-1800 model: 8 MB
FS-1800N model: 24 MB
264 MB (Including main RAM)
2 DIMM slots
(A 16 MB DIMM is factoryinstalled in one slot for FS-1800N.)
16, 32, 64, 128 MB
CompactFlash
Microdrive (340 MB)
High-speed, bidirectional
(IEEE1284)
RS-232C,
Maximum speed: 115.2 Kbps
10/100 Base-TX, type IB-21
(Standard with equipped FS1800N)
Prescribe
PCL6, Diablo 630, IBM
proprinter X24E, Epson LQ850,
Line printer, KPDL
FS-3800/3800N
PowerPC740/200MHz
FS-3800 model: 16 MB
FS-3800N model: 32 MB
272 MB (Including main RAM)
2 DIMM slots
(A 16 MB DIMM is factoryinstalled in one slot for FS-3800N.)
Width:
Height:
Depth:
Weight:
FS-1800/1800N
34.5 cm (13-9/16 inches)
30.0 cm (11-13/16 inches)
39.0 cm (15-3/8 inches)
13 Kg (28-5/8 lb.)
FS-1800/1800N | FS-3800/3800N
1-4
FS-3800/3800N
Watts
FS-1800/1800N
US/Canada: 120 V AC 10 %,
60 Hz 2 %/7.2 A
Europe/Asia: 220 - 240 V AC 10 %,
50/60 Hz 2 %/3.6 A
Average: FS-1800 model: 328 W
FS-1800N model: 961 W
Maximum: 120 V AC model: 961 W
220 - 240 V AC model: 961 W
Standby (Ready): FS-1800 model: 21 W
FS-1800N model: 23 W
Sleeping: FS-1800 model: 14 W
FS-1800N model: 15 W
FS-3800/3800N
FS-1800/1800N
10 to 32.5 C (50 to 90.5 F),
20 to 80 %RH
2,000 m (6,500 feet)
Maximum: 53 dB(A) ,
Standby: 35 dB(A)
FS-3800/3800N
Maximum: 57 dB(A) ,
Standby: 39 dB(A)
FS-1800/1800N | FS-3800/3800N
1-5
Manufacturer
Melco Inc.
Capacity
16 MB
32 MB
64 MB
Model
PM-HP-16M-KC
PM-HP-32M-KC
PM-HP-64M-KC
128 MB
PM-HP-128M-KC
FS-1800/1800N | FS-3800/3800N
1-6
FS-1800/1800N | FS-3800/3800N
1-7
Viking
Kingston
Capacity
8 MB
16 MB
24 MB
32 MB
48 MB
64 MB
96 MB
4 MB
8 MB
12 MB
16 MB
24 MB
32 MB
48 MB
64 MB
80 MB
8 MB
16 MB
24 MB
32 MB
48 MB
64 MB
96 MB
FS-1800/1800N | FS-3800/3800N
1-8
Model
SDCFBS-8-101
SDCFBS-16-101
SDCFBS-24-101
SDCFBS-32-101
SDCFBS-48-101
SDCFBS-64-101
SDCFBS-96-101
CF4M
CF8M
CF12M
CF16M
CF24M
CF32M
CF48M
CF64M
CF80M
CF/8
CF/16
CF/24
CF/32
CF/48
CF/64
CF/96
Manufacturer
DelkinDevices Inc.
HITACHI
Transcend
SST
LEXAR Media
Capacity
8 MB
16 MB
24 MB
32 MB
48 MB
64 MB
96 MB
8 MB
16 MB
32 MB
48 MB
64 MB
4 MB
8 MB
16 MB
32 MB
8 MB
16 MB
24 MB
32 MB
48 MB
64 MB
96 MB
16 MB
32 MB
48 MB
64 MB
80 MB
Model
DDCFFLS2-008
DDCFFLS2-016
DDCFFLS2-024
DDCFFLS2-032
DDCFFLS2-048
DDCFFLS2-064
DDCFFLS2-096
HB286008C4
HB286016C4
HB289032C4
HB289048C4
HB288064C5
TS4MFLASHCP
TS8MFLASHCP
TS16MFLASHCP
TS32MFLASHCP
SST48CF008
SST48CF016
SST48CF024
SST48CF032
SST48CF048
SST48CF064
SST48CF096
-
FS-1800/1800N | FS-3800/3800N
1-9
1
0
9
4
7
5
8
&
1 Top cover
2 Toner container
3 Operator panel
4 Paper gauge
5 Paper cassette
6 Paper size window
7 Power switch
8 Paper size dial
9 Waste toner bottle
0 Side cover
$
! Charger Cleaning knob
%
@ Paper stopper
^
# Face-down output tray
$ Memory card slot
) Parallel interface connector
% Paper feed unit
Serial interface connector
^ Paper feed unit release lever
Option unit connector
& MP tray
Network interface card *1
*1
* Rear cover
: Standard-installed with the FS-1800N/3800N
( AC inlet
models (Normally covered with a cover plate)
Figure 1-2-1 Name of parts
FS-1800/1800N | FS-3800/3800N
1-10
FS-1800/1800N | FS-3800/3800N
1-11
WARNING
1-12
FS-1800/1800N | FS-3800/3800N
1-13
FS-1800/1800N | FS-3800/3800N
1-14
FS-1800/1800N | FS-3800/3800N
1-15
FS-1800/1800N | FS-3800/3800N
1-16
(1) Clearance
Allow the necessary minimum clearance on all sides of the printer as below.
4
1
3
2
Clearance
Left
Front
Right
Back
Head room
Dimensions [Minimum]
30 cm (11-13/16 inches)
60 cm (23-5/8 inches)
25 cm (9-7/8 inches)
20 cm (7-7/8 inches)
30 cm (11-13/16 inches)
FS-1800/1800N | FS-3800/3800N
1-17
FS-1800/1800N | FS-3800/3800N
1-18
FS-1800/1800N | FS-3800/3800N
1-19
As the Ecosys printers are designed to ensure the optimum print quality when
used with Kyoceras proprietary toner, Kyocera do not recommend to use any
refilled toner containers that may be available commercially. This is because
Kyocera have no means of control over how such refilled toner could affect the
print quality and the reliability of the printer.
The toner container is not designed for disassembly or refilling. Do not attempt
to disassemble or refill the toner container.
FS-1800/1800N | FS-3800/3800N
1-20
20 to 40 C (4 to 104 F)
15 to 90 % RH
NOTE
CAUTION
If the printer is shipped for return, etc., do not ship it with the toner container
installed. Remove the toner container from the developer and put in a plastic
bag and seal the plastic bag. Otherwise, toner may leak and contamination may
result in the printer.
FS-1800/1800N | FS-3800/3800N
1-21
Chapter 2
Installation/Operation
Chapter 2 Contents
2-1 Unpacking ......................................................................................................................................... 2-3
2-1-1 Unpacking and inspection ......................................................................................................... 2-3
2-2 Installing the printer ........................................................................................................................ 2-5
2-2-1 Installing the toner container ..................................................................................................... 2-5
Removing the toner container ......................................................................................................... 2-7
2-2-2 Installing the waste toner bottle ................................................................................................. 2-8
Removing the waste toner bottle .................................................................................................... 2-9
2-2-3 Developer initialization (automatic) .......................................................................................... 2-10
2-2-4 Expanding the memory (DIMM) ............................................................................................... 2-11
(1) Minimum memory requirements .............................................................................................. 2-11
(2) DIMM specifications ................................................................................................................ 2-11
(3) Notes on handling DIMM ......................................................................................................... 2-12
(4) Installing the DIMM .................................................................................................................. 2-13
(5) Testing the expansion memory ............................................................................................... 2-14
(6) Installing the option hard disk (Microdrive) .............................................................................. 2-15
(7) Installing the option memory card (CompactFlash) ................................................................. 2-16
(8) Installing the option network interface card ............................................................................. 2-17
2-3 Using the operator panel ............................................................................................................... 2-18
2-3-1 Operator panel ......................................................................................................................... 2-18
(1) Indicators and keys .................................................................................................................. 2-18
(2) Interface indicator .................................................................................................................... 2-20
(3) Paper size indicator ................................................................................................................. 2-20
(4) Paper type Indicator ................................................................................................................ 2-21
(5) Message display ...................................................................................................................... 2-22
2-3-2 Menu selection system ............................................................................................................ 2-23
(1) Menu selection and sequence ................................................................................................. 2-23
2-1 Unpacking
2-1-1 Unpacking and inspection
The printer package should contain the items as shown in the figure below. After unpacking, remove
the printer and all the accessories from the package.
For unpacking, place the box containing the printer on a flat, stable surface. Remove the manuals,
toner kit, and other items located on top of the spacer. Then remove the spacer. Carefully remove
the printer. Obtain help from other persons if necessary.
For the FS-1800N/3800N, the CD-ROM (Network library) and the manual for the network interface
card are shipped together with the components listed below.
7
56
1
2
1 Printer
2 Toner container
3 Waste toner bottle
4 Power cord
5 Installation manual
6 Kyocera digital library CD-ROM
7 Plastic bag
FS-1800/1800N | FS-3800/3800N
2-3
1 Printer
2 Toner container
3 Waste toner bottle
4 Power cord
5 Installation manual
6 Kyocera digital library CD-ROM
7 Plastic bag
FS-1800/1800N | FS-3800/3800N
2-4
FS-1800/1800N | FS-3800/3800N
2-5
FS-1800/1800N | FS-3800/3800N
2-6
Do not remove the toner container unless you need to do so for servicing, etc.
FS-1800/1800N | FS-3800/3800N
2-7
FS-1800/1800N | FS-3800/3800N
2-8
Do not remove the waste toner bottle unless you need to do so for service, etc.
1
Figure 2-2-6 Removing the waste toner bottle
FS-1800/1800N | FS-3800/3800N
2-9
Do not turn printer power off during the developer is initialized. If the printer is
switched off in the middle of developer initialization, even after the printer is
switch on again, the printer will not automatically resumes developer
initialization. Should this be the case, enforce the printer to resume developer
initialization in the following manner:
1. While the printer is turned off, press and hold the GO and CANCEL keys.
2. Turn printer power on.
3. Let go off of the GO and CANCEL keys for more than 5 seconds.
Developer initialization resumes for the rest of the required total time.
4. Wait until the READY indicator is lit and the message display indicates Ready.
5. Make a test print by printing a status page. To print a test page, proceed as follows;
1 Press the MENU key on the printer.
2 Press the key or key repeatedly until the message display shows Print Status
Page.
3 Press the ENTER key twice.
6. If the status page is printed satisfactorily, setup is complete. If not, investigate whether all step
procedures are properly followed.
FS-1800/1800N | FS-3800/3800N
2-10
Printing environment
PCL6, duplex mode = None
PCL6, duplex mode = On
KPDL, duplex mode = None
KPDL, duplex mode = On
PCL6/KPDL resource protection,
duplex mode = None
PCL6/KPDL resource protection,
duplex mode = ON
300 dpi
8 MB
8 MB
8 MB
8 MB
-
Resolution
600 dpi
1200 dpi
Fast mode
Fine mode
8 MB
8 MB
8 MB
8 MB
8 MB
12 MB
8 MB
8 MB
8 MB
8 MB
12 MB
12 MB
10 MB
10 MB
10 MB
14 MB
14 MB
14 MB
Specification
16, 32, 64, 128 MB
100 pins
66 MHz
None
32 bits
FS-1800/1800N | FS-3800/3800N
2-11
Before touching a DIMM, touch a water pipe or other large metal object to
discharge yourself of static electricity.
While doing the work, it is recommended that you wear an antistatic wrist
strap.
Touch the main board and DIMM only by the edges, not in the middle.
FS-1800/1800N | FS-3800/3800N
2-12
CAUTION
Be sure that no foreign objects such as metal chips or liquid get inside the
printer during installing DIMMs. Operation of the printer during the presence
of a foreign substance may lead to fire or electric shock.
WARNING
Before proceeding installation, turn the printers power switch off. Unplug the
printers power cable and disconnect the printer from the computer or the
network.
3
3
Figure 2-2-8 Removing the main board
FS-1800/1800N | FS-3800/3800N
2-13
FS-1800/1800N | FS-3800/3800N
2-14
Take precautions that no foreign objects such as metal chips or liquid get inside
the printer during the installation process. Operation of the printer during the
presence of a foreign objects may lead to fire or electric shock.
WARNING
Turn the printers power switch off. Unplug the printers power cable and
disconnect the printer from the computer or the network.
FS-1800/1800N | FS-3800/3800N
2-15
FS-1800/1800N | FS-3800/3800N
2-16
Be sure that no foreign object such as metal chips or liquid get inside the
printer during the installation process. Operation of the printer during the
presence of a foreign object may lead to fire or electric shock.
WARNING
Turn the printers power switch off. Unplug the printers power cable and
disconnect the printer from the computer.
2
1
3
3
Figure 2-2-13 Installing the option network interface card
FS-1800/1800N | FS-3800/3800N
2-17
Message display
$ # @
Condition
Flashing
Lit
Off
2 DATA indicator
Flashing
Lit
Description
An error has occurred that the user can clear.
The printer is on-line and ready to print.
The printer is off-line. The printers stores but does not
print received data. This is also indicates when printing
is automatically stopped due to the occurrence of an error.
Data transfer between the printer and the computer is
taking place.
Either data is being processed, or data is being written
onto the option CompactFlash or Microdrive.
The printer needs maintenance attention or the printer is
warming up (Please wait).
A problem or an error has occurred that the user can
clear, for example, paper jam.
Operations are normal.
FS-1800/1800N | FS-3800/3800N
2-18
Key
4 GO key
5 CANCEL key
6 MENU key
key
key
9 < key
0 > key (
key)
! ENTER key
Function
Switches the printer on-line and off-line.
Prints and feed out one page.
Cancels a printing job.
To cancel a print job, proceed as follows:
1. Check the message Processing is displayed in the message
display.
2. Press the CANCEL key.
3. The message Print Cancel? will appear in the message display
and the interface to be canceled will be displayed.
Parallel
Serial
Option (appears only when an [option] network interface card is
installed)
Press the CANCEL key again if you wish to stop the cancellation of
printing.
4. Selecting the interface to cancel using the or key. Then press
the ENTER key. Printing from the interface selected will be stopped.
The Cancelling data message appears in the message display
and printing stops after the printer finishes printing the current page.
Resets numeric values, or cancels a setting procedure.
Stops the sound alarm that indicates the occurrence of an error.
Enter menu mode
When pressed during menu selection, terminates the setting and returns
to the Ready condition.
Lets you access the desired item or enter numeric values. In some of the
control procedures, the < and > keys are used to enter or exit the sub items.
Enables access to the desired item or entering of numeric values. In some
of the control procedures, the < and > keys are used to enter or exit the sub
items.
Used as the < key in the menu selection.
Used as the > key in the menu selection.
Displays on-line help messages on the message display when paper jam
occur. When pressed in the Ready condition, displays on-line help
messages.
Finalizes numeric values and other selections in menu selection.
FS-1800/1800N | FS-3800/3800N
2-19
Meaning
No interface is currently used
Standard bidirectional parallel interface
Serial interface (RS-232C)
[Option] network interface card
The PAR , SER , or OPT indicator flashes when the printer is receiving data and remains indicated
for the duration of the interface time-out time.
(3) Paper size indicator
The SIZE indicator # indicates the size of the current paper cassette. Default is Letter size for the
U.S.A. and A4 for European countrie. While the printer is Processing data to print, the SIZE indicator
switches to indicate the paper size selected by the application software.
The following abbreviations are used to indicate paper sizes.
Message
A4
DL
A5
C5
A6
b5
B5
EX
B6
#6
LT
#9
LG
HA
MO
OH
BU
CU
Paper size
ISO A4 (21 29.7 cm)
ISO DL (11 22 cm) *
ISO A5 (14.8 21 cm)
ISO C5 (16.2 22.9 cm) *
ISO A6 (10.5 14.8 cm) *
ISO B5 (17.6 25 cm) *
JIS B5 (18.2 25.6 cm)
Executive (7-1/4 10-1/2 inches) *
JIS B6 (12.8 18.2 cm) *
Commercial 6-3/4 (3-5/8 6-1/2 inches) *
Letter (8-1/2 11 inches)
Commercial 9 (3-7/8 8-7/8 inches) *
Legal (8-1/2 14 inches)
Japanese postcard (10 14.8 cm) *
Monarch (3-7/8 7-1/2 inches) *
Return postcard (20 14.8 cm) *
Business (4-1/8 inches) *
Custom size (14.8 21 cm to 21.6 35.6 cm)
* with only the MP tray feeding
FS-1800/1800N | FS-3800/3800N
2-20
FS-1800/1800N | FS-3800/3800N
2-21
Message
Self test
Please wait
Ready
Processing
Waiting
Sleeping
Cancelling data
FormFeed Time Out
Meaning
The printer is self-testing after power-up.
The printer is warming up and is not ready. When the printer is
switched on the first time after the toner container is installed,
(Adding toner) also appears.
The printer is ready to print.
The printer is receiving data, generating graphics, reading an memory
card (CompactFlash)/hard disk (Microdrive), or printing.
The printer is waiting for a command that says the job is over before
printing the last page. Pressing the GO key allows you to obtain the
last page immediately.
The printer is in Sleep mode. The printer wakes from Sleep mode
whenever a key on the operator panel is pressed, the cover is opened
or closed, or data is received. The printer then warms up and goes
on-line. (The time that it takes the printer to enter Sleep mode depends
on the Sleep Timer setting.)
Data inside the printer is being canceled.
The printer prints the last page after a waiting period.
FS-1800/1800N | FS-3800/3800N
2-22
Print
Menu Map
Print
Status Page
e-MPS
Interface
Serial
>
>Bau rate
9600
>
>Data Bits
8
>Quick Copy
>Stop Bits
1
>Private/Stored
>Parity
None
>Protocol
DTR (pos.)&XON
>List of VMB
>Barcode Mode
Off
Interface
Option
>List of
Code JOB
>
>NetWare
Off
>e-MPS
>
Configuration
>NetWare
On
>>Quick Copy
>>NetWare Frame
Auto
>>Temp.Code JOB
Size
Inter face
Parallel
>
>>Perm.Code JOB
Size
>TCP/IP
Off
>>VMB Size
>TCP/IP
On
>
>>DHCP
Off
>
>>IP Address
>Parallel I/F
Nibble (high)
>>Subnet Mask
>Parallel I/F
Auto
>>Gateway
>Parallel I/F
Normal
>Ether Talk
Off
>Parallel I/F
High Speed
>OPT. StatusPage
Off
Continued on next page.
FS-1800/1800N | FS-3800/3800N
2-23
Emulation
PCL 6
Font
Option
>
>Code set
ISO-6 ASCII
Emulation
KPDL
> I000
>Courier
Dark
>
>Print KPDL errs
Off
>Courier
Regular
>
>Letter Gothic
Regular
>
>Letter Gothic
Dark
>Alt. Emulation
PCL 6
>Size
012.00 point(s)
>Pitch
>List of Fonts
10.00 cpi
Emulation
>
IBM Proprinter
Page set
>Code set
IBM US
>
>Copies
Emulation
Line printer
>
001
>Orientation
Portrait
>Code set
IBM US
Emulation
DIABLO 630
>Orientation
Landscape
>
>Page Protect
Auto
>Code set
DIABLO US
Emulation
EPSON LQ-850
>Page Protect
On
>
>Code set
LQ US
Font
Internal
>LF Action
LF only
>LF Action
CR and LF
>
> I000
>LF Action
Ignore LF
>Courier
Dark
>CR Action
LF only
>Courier
Regular
>CR Action
CR and LF
>Letter Gothic
Regular
>CR Action
Ignore CR
>Letter Gothic
Dark
>Wide A4
Off
>Size
012.00 point(s)
>Wide A4
On
>Pitch
10.00 cpi
>List of Fonts
Continued on next page.
FS-1800/1800N | FS-3800/3800N
2-24
Print Quality
>
Memory Card
>
>KIR Mode
On
>Read Fonts
>KIR Mode
Off
>Read Data
>Ecoprint Mode
Off
>Write Data
>Ecoprint Mode
On
>Delete Data
>Resolution
Fast 1200 mode
>List of
Partitions
>Resolution
Fine 1200 mode
>Resolution
300 dpi
>Resolution
600 dpi
>Print Density
03
Opt. ROM
>
>Read Data
>List of
Partitions
Hard Disk
>
>Read Data
>Write Data
>Delete Data
>List of
Partitions
FS-1800/1800N | FS-3800/3800N
2-25
LIFE Counters
>
>Total Print
>EF Size
DL or Business
>New Toner
Installed
>EF Type
Plain
Others
>
>BulkFeeder Size
>Form Feed
Time Out 030sec.
>BulkFeeder Type
Plain
>Sleep Timer
>
005 min.
>>Unit
mm
>>Sleep Mode
Off
>>Unit
inch
>Print HEX-DUMP
>>X Dimension
>Printer Reset
>>Y Dimension
>Cassette Type
Plain
>Resource prot.
Off
>Feed Select
Cassette
>Resource prot.
Permanent
>Duplex Mode
None
>Resource prot.
Perm / Temp
>Stack Select
Face-down tray
>Buzzer
On
>Opt.StackerMode
Sorter
>Buzzer
Off
>Override A4/LT
Off
>Auto Continue
Mode On
>Override A4/LT
On
>Type Adjust
Custom 1
>>Auto Continue
Timer 000sec.
>
>Auto Continue
Mode Off
>>Paper weight
Normal
>Service
>>Paper weight
Heavy (Thick)
>
>>Print
Status Page
>>Paper weight
Light (Thin)
>>Toner ID
>>Duplex Path
Disable
>>Developer
>>Duplex Path
Enable
>>Drum
>Reset Type
Adjust
FS-1800/1800N | FS-3800/3800N
2-26
Chapter 3
Maintenance/Adjustments
Chapter 3 Contents
3-1 Maintenance/Adjustments .............................................................................................................. 3-3
3-1-1 Life expectancy of modules ....................................................................................................... 3-3
3-1-2 Toner container ......................................................................................................................... 3-4
(1) When to replace the toner container ......................................................................................... 3-4
(2) Notes on changing the toner container ...................................................................................... 3-4
(3) Toner container replacement ..................................................................................................... 3-5
(4) Toner saver mode (EcoPrint) .................................................................................................... 3-6
(5) Replacing the waste toner bottle ............................................................................................... 3-7
3-1-3 Cleaning the printer ................................................................................................................... 3-8
(1) Main charger unit ....................................................................................................................... 3-8
(2) Cleaning the main charger wire and grid ................................................................................... 3-9
Main charger wire ........................................................................................................................... 3-9
Grid ............................................................................................................................................... 3-10
(3) Paper feed unit ........................................................................................................................ 3-12
(4) Replacing the developer .......................................................................................................... 3-13
Shipping the developer ................................................................................................................. 3-13
(5) Developer initialization (Toner install mode) ............................................................................ 3-14
(6) Developer refreshing mode ..................................................................................................... 3-15
(7) Drum cleaning mode ............................................................................................................... 3-16
3-1-4 Updating the firmware ............................................................................................................. 3-17
(1) Firmware program data format ................................................................................................ 3-18
(2) Downloading the engine and controller firmware .................................................................... 3-18
From the parallel interface ............................................................................................................ 3-18
From the memory card (CompactFlash) ....................................................................................... 3-20
(3) Downloading operator panel message data ............................................................................ 3-21
(4) Downloading errors ................................................................................................................. 3-22
3-1 Maintenance/Adjustments
3-1-1 Life expectancy of modules
The table below shows the nominal life expectancy for modules. Detailed part information for each
module (except toner containers) can be found in the separate Parts Catalog.
Table 3-1-1 Life expectancy of modules
Module
Toner container*1
Drum unit
Developer
Fuser unit
Main charger unit
Refurbishment kit*2
Model
FS-1800/1800N
FS-3800/3800N
TK-60
TK-60E
DK-60
DK-61
DV-60
DV-61
DV-62
FK-60*3
FE-60
MK-60
FK-61*3
FE-61
MK-61
300,000
300,000
300,000
*1
: User-replaceable
*2
*3
: Each FK kits have two voltage type for 120 V AC and 220 - 240 VAC.
FS-1800/1800N | FS-3800/3800N
3-3
Kit
Life in pages
TK-60
20,000
TK-60E
10,000
Based on letter or A4 size paper; average print coverage of 5 %
NOTE
3-4
FS-1800/1800N | FS-3800/3800N
3-5
Put the old toner container in the supplied plastic bag 3 and dispose of it.
See also the instructions provided in chapter 2, Installing the toner container on page 2-5 to complete
installation of the new toner container.
(4) Toner saver mode (EcoPrint)
The EcoPrint enables to reduce the amount of toner consumed on the page so as to save printing
costs by drastically extending the toner container life. EcoPrint mode is factory-set to off and
turned on by using the menu system of the printer operator panel. For details, see the printers
Users Manual.
FS-1800/1800N | FS-3800/3800N
3-6
FS-1800/1800N | FS-3800/3800N
3-7
Cleaning pad
Main charger wire
Grid
Shield
Cleanig knob
FS-1800/1800N | FS-3800/3800N
3-8
Cleaning knob pulls a cleaning pad inside the drum unit along the main charger wire.
1
2
FS-1800/1800N | FS-3800/3800N
3-9
Grid
1. Take the grid cleaner 1 from protective bag 2 in the new toner kit and remove the cap 3.
NOTE
The grid cleaner pad is impregnated with water. Perform the following
cleaning procedure before the pad dries.
1
2
FS-1800/1800N | FS-3800/3800N
3-10
3. After attaching the grid cleaner, repeat the action of slowly pulling out and then pushing back in
the main charger unit at least 5 times. It is easier to pull out the main charger with its front end
raised slightly as shown in the figure. The grid part underneath the main charger is cleaned by
the wet pad of the grid cleaner.
FS-1800/1800N | FS-3800/3800N
3-11
Do not touch the transfer roller 5 (black sponge roller) when wiping the paper
ramp 3.
Area 6 below is factory-applied with lubricating oil. When cleaning the paper
feed unit 7, do not use alcohol to clean this area. If the oil is completely removed,
an incorrect action of the MP tray paper sensor (8, actuator) will result.
8
6
5
2
4
Figure 3-1-9 Cleaning the upper registration roller and the paper ramp
FS-1800/1800N | FS-3800/3800N
3-12
1
3
2
4
3-13
Display to show
Remarks
Others
>
>Service
>
>>Developer
>>Developer?
Paper size
switch
Ready
8 Turn printer power
off then on.
When printer power is turned on again, the printer continually engages in this mode for a period of
approximately 15*1/8*2 minutes, after which the printer reverts to the ready state.
*1
: Developer DV-60/DV-61
*2
: Developer DV-62
FS-1800/1800N | FS-3800/3800N
3-14
NOTE
The amount of the (old) toner replaced and collected in the waste toner bottle
will be approximately 100 g. The waste toner bottole consequently become full
and must be replaced with a new one.
Perform in sequence:
1 Turn printer power on.
2 Make sure the printer is Ready.
(Connect the printer to the computer using the parallel interface.
3 At the DOS prompt, send the following command to the printer:
>ECHO !R!EXTP 7,92;EXIT;>PRN
4 Turn printer power off, then on. The toner refreshing mode will
begin. The old toner will be rejected in the first approximately 20
minutes, followed by another 40 minutes interval in which the new
toner is fed in the developer unit.
Paper size
switch
Display shows:
Ready
Please Wait
(Adding toner)
Ready
Print density
03
FS-1800/1800N | FS-3800/3800N
3-15
Display to show
Remarks
Others
>
>Service
>
>>Drum
>>Drum?
FS-1800/1800N | FS-3800/3800N
3-16
Controller system DIMM: Firmware update is possible with flash ROM type
system DIMM [board] only. Masked type system DIMM [board] can not be
overwritten. Check the type of the system DIMM [board] used on the main
board by referring to the figure below.
If the DIMM has a Kyocera logo and firmware version label, the DIMM is a
masked-type and can not be updated. To update firmware for this type of
system DIMM, replace the DIMM.
Flash ROM (U202)
Engine board
Masked type
system DIMM [board]
Main board
Firmware version
Kyocera logo
Figure 3-1-11 Engine flash ROM (U202) and masked type system DIMM [board]
Engine flash ROM: The engine flash ROM (U202) is directly mounted on the
engine board. Updating the engine firmware is possible only by downloading
the data in the manner described in the following sections.
FS-1800/1800N | FS-3800/3800N
3-17
Kyocera supplies the following types of data for updating firmware of the different purposes:
Controller firmware
Engine firmware
Operator panel message data
(1) Firmware program data format
The data to be downloaded are supplied in the following format:
Identifies...
1
de3730.dat
1
2
3
4
FS-1800/1800N | FS-3800/3800N
3-18
NOTE
The computer that MS-DOS is usable is necessary for a download from parallel interface. It is
necessary for a computer to be connected to a printer with a parallel cable.
Self test
Make sure the printer is Ready.
Ready
At the DOS prompt, send the
following command to the
printer:
>ECHO !R! UPGR'SYS';EXIT;>PRN
Note: Do not add an EXIT;
command in the above.
The message display should
indicate Supervisor mode.
Supervisor mode
Copy the engine or controller
firmware data to the printer by
typing:
>COPY\B program file name PRN
Downloading is performed in
the sequence explaned in the
right-hand column.
Turn power on again.
Check the printer gets Ready.
Ready
Confirm that the status page
shows the new firmware
version.
Supervisor mode
Supervisor mode
palallel waiting
data receiving
>>>>>>>>>>>
BootROM
erase&write
engine download
<<<<<<<<<<<
Means more
than one data
Finished.
Version
52.00S
01/03/31[1234] 2
A37
A3
01/03/31[1234] 2
Year/Month/Day [Checksum]
: Controller (System)
: Engine
Confirm that the status page shows the new engine firmware or controller firmware version (See Appendix B on page B-4).
If the message display indicates Call service personDn (n=0, 1, ...), refer to section Downloading errors on page 3-20.
FS-1800/1800N | FS-3800/3800N
3-19
NOTE
The system or engine firmware program data must be stored to the root
directory of the memory card (CompactFlash).
Supervisor mode
Supervisor mode
Supervisor mode
CF-CARD Reading
BootROM
erase&write
Memory card
Self test
Downloading is performed in
the sequence explaned in the
right-hand column.
engine download
<<<<<<<<<<<
Means more
than one data
Finished.
Version
52.00S
01/03/31[1234] 2
Ready
Confirm that the status page
shows the new firmware
version.
Year/Month/Day [Checksum]
Means more
than one data
Machine code, Version
A37
A003
01/03/31[1234] 2
Year/Month/Day [Checksum]
: Controller (System)
: Engine
page B-4). If the message display indicates Call service person Dn (n=0, 1, ...), refer to
section Downloading errors on page 3-20.
FS-1800/1800N | FS-3800/3800N
3-20
Downloading operator panel message data takes several minutes. Do not turn
power off during downloading.
Perform in sequence
1 Turn printer power on.
2 Make sure the printer is Ready.
Display shows
Ready
Supervisor mode
parallel waiting
Downloading
Ready
FS-1800/1800N | FS-3800/3800N
3-21
Call service
perosonD1
Call service
perosonD2
Call service
perosonD3
Meaning
Checksum error
Checksum error occurred during
downloading. The flash ROM is
empty.
Machine compatibility error
The data to be downloaded is not
compatible with the printer.
Version compatibility error
The version of the data does not
match the current engine version.
Data error
The data to be downloaded is
corrupted.
Corrective action
Turn printer power off once, then
on again. Try downloading
again.
Obtain correct data for the
printer model.
Obtain the correct version of
data.
Obtain the correct data.
If the corrective action above does not solve the problem, replace engine board (KP-864). See page
5-22.
FS-1800/1800N | FS-3800/3800N
3-22
Chapter 4
Operation
Overview
Chapter 4 Contents
4-1 Electrophotographic system .......................................................................................................... 4-3
4-1-1 Electrophotographic cycle ......................................................................................................... 4-3
(1) Main charging ............................................................................................................................ 4-4
Components of drum and main charger unit ................................................................................... 4-4
Amorphus-silicon drum ................................................................................................................... 4-5
Charging the drum .......................................................................................................................... 4-6
(2) Exposure ................................................................................................................................... 4-7
Laser scanner unit .......................................................................................................................... 4-8
Drum surface potential .................................................................................................................. 4-10
(3) Development ........................................................................................................................... 4-11
(4) Transfer ................................................................................................................................... 4-14
(5) Fusing ...................................................................................................................................... 4-15
Fuser unit mechanism ................................................................................................................... 4-16
(6) Cleaning .................................................................................................................................. 4-17
4-2 Paper feeding system .................................................................................................................... 4-18
4-2-1 Paper feed control ................................................................................................................... 4-19
(1) Paper feeding mechanism ....................................................................................................... 4-20
Drive and paper feed unit .............................................................................................................. 4-20
MP tray paper feed unit ................................................................................................................. 4-21
Fuser unit and face up/down output .............................................................................................. 4-22
4-3 Electrical control system .............................................................................................................. 4-23
4-3-1 Electrical parts layout .............................................................................................................. 4-23
(1) Circuit boards, sensors and switches ...................................................................................... 4-23
(2) Motors, solenoids, clutches and others ................................................................................... 4-24
(3) Drum unit and developer ......................................................................................................... 4-25
4-3-2 Operation of circuit boards ...................................................................................................... 4-26
(1) Main board ............................................................................................................................... 4-26
Main board KP-777 for FS-1800/1800N models ........................................................................... 4-26
Main board KP-858 for FS-3800/3800N models ........................................................................... 4-27
(2) Engine board ........................................................................................................................... 4-28
Eraser lamp control circuit ............................................................................................................ 4-29
Toner motor control circuit ............................................................................................................ 4-30
Heater lamp control circuit ............................................................................................................ 4-31
(3) Sensor board ........................................................................................................................... 4-33
Paper gauge sensing circuit .......................................................................................................... 4-33
Interlock circuit .............................................................................................................................. 4-34
Paper size detecting circuit ........................................................................................................... 4-36
(4) Power supply unit .................................................................................................................... 4-38
(5) High voltage unit ...................................................................................................................... 4-39
Drum unit
Laser scanner unit
1 Main charging
6 Cleaning
2 Exposure
Drum
3 Developing
Developer
4 Transfer
5 Fusing
Fuser unit
FS-1800/1800N | FS-3800/3800N
4-3
2
6
1
Drum unit
9
0
7
8
$
5
4
8 Cleaner screw
9 Drum gear Z36H
0 Drum
! Main charger shield
@ Grid
# Main charger wire
$ Charger wire cleaner
FS-1800/1800N | FS-3800/3800N
4-4
Amorphus-silicon drum
The printer use the long lasting amorphous silicon drum. The drum surface is a composite of five
substances coated in five layers as shown below.
Drum
1 Aluminum base
2 Carrier block (1 to 3 m thick)
3 Photoconductor a-Si
4 Primary protection layer (1 m thick)
5 Secondary protection layer
Figure 4-1-3 Amorphus silicon drum
The primary and secondary layers are for protecting the amorphous silicon layer underneath. The
amorphus silicon layer is of photoconductive, meaning it can be electronically conductive when
exposed to a (laser) light source to effectively ground electrons charged on its outer surface to the
ground. This layer is approximately 9 m thick.
The carrier block layer lies between the amorphous silicon layer and the aluminum base cylinder
and prevents the backward electron flow, from the base cylinder to the drums outer surface, which
might give adverse effect (possibly ghost) on the print quality.
FS-1800/1800N | FS-3800/3800N
4-5
Main charging
output
Engine board
MCHON*
YC204-10
B
C
Zener
board
KP-768
FS-1800/1800N | FS-3800/3800N
4-6
(2) Exposure
The charged surface of the drum A is exposed to the laser beam scanning from the laser scanner
unit B.
E
D
Laser beam
output
FS-1800/1800N | FS-3800/3800N
4-7
3
2
1
9
0
8
7
Figure 4-1-6 Laser scanner unit
Name
1 Laser diode
2 Collimator lens
3 Cylindrical lens
4 Polygon motor
Description
Emits diffused, visible laser.
Aligns the laser beam to the cylindrical lens.
Compensates the vertical angle at which the laser beam hits on of the
polygon mirror segments.
Has six mirror segments around its hexagonal circumference. Each
mirror corresponds to one scanned line width on the drum when the
laser beam scans on it.
FS-1800/1800N | FS-3800/3800N
4-8
Name
5 Primary f-theta lens
6 Secondary f-theta lens
7 Diversion mirror
8 Protective glass
9 Sensor mirror
0 Pin photo sensor
Description
See figure 4-1-7 below.
The primary (above) and secondary f-theta lenses equalize focusing
distortion on the area on the drum closer to the edge. The effective
length of line (A, B in the figure below) the laser beam draws on
the drum becomes longer as the laser beam hits closer to the drum
edge. In the figure 4-1-7 below, distances represented by A and B
are not the same (A > B) until the f-theta lenses are provided between
the polygon mirror and the drum (A = B).
Diverts the laser beam vertically onto the drum. Note the diffused
laser beam finally pinpoints on the drum.
Prevent dust, debris, etc., from entering the scanner assembly.
Bends the very first shot of a laser scan towards the pin photo sensor
(below).
When shone by the sensor mirror above, this pin photo sensor
generates a trigger signal.
Polygon mirror
Laser diode
Laser beam
Drum
FS-1800/1800N | FS-3800/3800N
4-9
Laser beam
a-Si layer
Drum
Aluminum base
FS-1800/1800N | FS-3800/3800N
4-10
(3) Development
Power train
A
A
7
6
Toner container
1
B
4
5
Developer
1 Toner motor
2 Toner sensor
3 Developing roller
4 DLP A screw
5 DLP B screw
6 Blade
7 Magnet
4-11
The latent image constituted on the drum A is developed into a visible image. The developing
roller B contains a 4-pole (S-N-S-N) magnet core C and an aluminum cylinder rotating around
the magnet core C. Toner attracts to the developing roller B since it is powdery ink made of black
resin bound to iron particles. Blade D magnetized by magnet E is positioned approximately 0.3
to 0.4 mm above the developing roller B. It constitutes a smooth layer of toner in accordance with
the revolution of the roller.
Magnetism
0.1 mm
0.3 to 0.4 mm
N
S
F
S
N
N
Engine board
High
voltage
unit
S
150 V DC + AC
CN2-11
HVCLK
YC204-8
Developing bias
output
B C
FS-1800/1800N | FS-3800/3800N
4-12
A toner sensor is provided within the developer. As the toner supply from the toner container
dwindles and the toner level lowers in the reservoir, the sensor translates it into an electrical signal
through its diaphragm, urging the toner motor to feed more toner.
Toner container
Toner hopper
Toner motor
Sensable level
Diaphragm
Toner
Toner sensor
Developer
FS-1800/1800N | FS-3800/3800N
4-13
(4) Transfer
The image developed by toner on the drum A is transferred onto the paper because of the electrical
attraction between the toner itself and the transfer roller B. The transfer roller B is negativelybiased so that the positively-charged toner is attracted onto the paper while it is pinched by the
drum A and the transfer roller B.
A
S
N
S
B
Transfer
bias
output
Normal
Thick
Thin
Voltage
Current
65 A
Engine
board
High
voltage
unit
Paper type
Transfer bias
output
TR
CN2-13
TRCHON*
YC204-6
FS-1800/1800N | FS-3800/3800N
4-14
(5) Fusing
The toner on the paper is molten by heat and pressed into the paper as it passes between the heat
roller A and the press roller B in the fuser unit.
Fusing control temperature
Model FS-1800 FS-3800
FS-1800N FS-3800N
Paper type
Thin
A4 Normal
Thick
B5
Thick
A5 or Normal
smaller Thick
Ready
Engine
board
THERM
YC202-6
HEATON*
YC202-11
Power
supply
unit
AC power
off/on
output
B
Figure 4-1-13 Fusing
The heat roller A has a heater (infrared) lamp C inside which continuously turns on and off by the
thermistor to maintain the constant temperature on the heat roller A surface. The fusing temperature
is also controlled based on paper types. See the table in the figure above.
The heat roller A is florin coated by to prevent toner from accumulating on the roller after a long
usage. Care must be taken while handling the heat roller A not to scratch the roller surface as
doing so may result in quality problems.
The heat roller A has four scraping claws (Separators) D which are continuously in contact with
its surface. These claws prevent the paper on which toner has been fused from being wound around
the heat roller A causing paper jam.
The press roller B is made of the heat resistant silicon rubber. This roller is used to strongly press
the paper towards the heat roller A by means of coil springs.
The temperature of the heat roller A is constantly monitored by the engine board using the thermistor
and triac. Should the temperature of the heat roller A exceed the predetermined value, the thermal
cutout is activated to effectively disconnect the heater lamp C from power.
FS-1800/1800N | FS-3800/3800N
4-15
To face-down
output tray
1
23
$
To face-up
output tray
or option devices
9
4
@
!
Paper from
paper feed unit
(transfer section)
0
^
6
7 Heat roller
8 Exit roller
9 Exit pulley(s)
0 Heat gear Z36*1/Z46*2
! Exit gear Z21
@ Idle gear Z18*1/Z28*2
: FS-1800/1800N
FS-1800/1800N | FS-3800/3800N
4-16
*2
: FS-3800/3800N
(6) Cleaning
After the transferring process, the drum needs to be physically cleaned of toner which is residual
after the development process. The cleaning blade A is constantly pressed against the drum B and
scrapes the residual toner on the drum off to the cleaning roller C. The cleaning roller drives the
toner to the cleaner screw D at one end of which the waste toner bottle is connected to collect the
waste toner.
E
B
D C
FS-1800/1800N | FS-3800/3800N
4-17
1
2
3
&
4
^
$
7
#
1 Middle feed roller
2 MP tray feed roller
3 Guide pulley(s)
4 MP tray
5 Paper cassette
6 Feed pulley
7 Retard roller
@ !
9 8
8 Feed roller
9 Pickup roller
0 Upper registration roller
! Lower registration roller
@ Transfer roller
# Drum
$ Press roller
% Heat roller
^ Exit roller
& Exit pulley(s)
* FD roller
( Pinch roller(s)
) Face-down output tray
4-18
Toner container
5
Laser
scanner
unit
Drum unit
Developer
Fuser board
HANDS*
High voltage
unit
YC204-13
MPFSOL*
YC206-3
MIDDR*
YC206-5
REGDR*
FDDR*
YC206-11
Engine board
YC206-15
YC203-17
REGPAP
EXITPAP*
YC202-6
FDPFUL*
YC202-2
YC202-4
FDDR
FUDR
Sensor
baord
YC206-18
Paper cassette
YC202-3
MP tray
9 3
Fuser unit
: Power train
1 Main motor
2 MP tray paper sensor
3 Registration sensor
4 Exit sensor
9 Registration clutch
0 Face up/down solenoid
FS-1800/1800N | FS-3800/3800N
4-19
Power train
To fuser unit
4
5
1 Main motor
2 Registration clutch
3 Feed clutch
4 Pickup roller
5 Feed roller
6 Lower registration roller
7 Upper registration roller
8 Transfer roller
4-20
Drive unit
D C
Power train
9
MP tray paper feed unit
!
D
MP tray
FS-1800/1800N | FS-3800/3800N
4-21
To face-up
output tray or
option device
Power train
%
F
Paper from
paper feed unit
$
Drive unit
F
#
Fuser unit
# Heat roller
$ Press roller
% Exit roller
^ Exit pulley(s)
& FD roller
* Pinch roller(s)
FS-1800/1800N | FS-3800/3800N
4-22
9
!
2
3
^
4
%
#
$&
*2
*
(
$ Paper gauge sensor 2 (PH703)
4-23
3
2
98
5
0
6
7
4
!
1 Main motor
2 Polygon motor
3 Cooling fan motor
4 Controller unit fan motor
9 Registration clutch
0 Heater lamp
! AC inlet
FS-1800/1800N | FS-3800/3800N
4-24
5
4
Drum unit
Developer
FS-1800/1800N | FS-3800/3800N
4-25
U16
YS01
CSN [1:0],
OEN0,
WEN0
U03-U05
CSN2,
OEN0,
WEN0
Image
chip
XLIDATA, SRCCLKN
ROMA [4:2]
LA [22:2]
Buffers
System
DIMM
[board]
LA [3:2]
CPUD [31:24]
CPUD [31:0]
CPUD [15:0]
U06-U07
CPUA [31:0]
U01
EXTBOEN,
EXTDIR
Buffers
CPUD [31:0]
CPU
PowerPC405GF
200 MHz
U08, U09S
ROMA1
BCLK, BGN,
TAN, TEAN,
RSTOUTN, CPUINTN
LA [21:2]
LD [15:0]
X01
Xtal
50.0000 MHz
LA22,
LA [11:2]
YC06
Xtal
25.50629 MHz
KUIOCSN1
IORN1, IOWN1,
OPRDY1,
DMAACKN1
OPRST1,
IODTACKN1,
OPIRN1,
DMAREQ1
YC04
U10
LA [16:2]
SDD [31:0]
SDRAM
YS02
Expanding
SDRAM
(DIMM)
YS03
Expanding
SDRAM
(DIMM)
U12-U15
NAND
U17
Engine
Board
EXTBOEN,
CFOEN1
Buffers
U31
U22T
AND
YC01
KUIO
LD [15:0]
SDCLK, SDCKE,
SDCSN [5:0],
SDRAS, SDCAS,
SDWEN,
DQMUU, DQMUM,
DQMLM, DQMLL
IICSDA, IICSCL
2nd Optional
Interface
CFCSN1, CFCSN2,
CFOEN2, CFWEN2,
CDET2A, CDET2B,
CFRST2,
CFWAITN2
Option
hard disk
(Microdrive)
LD [15:0]
X02
YC07
CSN [3:2],
OEN1,
(WEN0)
FONTs
Centronics
Buffer
YC02
P1284HD,
ACK,
BUSY,
PERROR,
SELECT,
FAULT,
P1284DIR,
SELECTIN,
STROBE,
AUTOFD,
INIT,
P1284DIR
XTXD,
XDTR,
XRTS,
XDSR,
XCTS,
XRXD,
RSSEL
CFA22,
CFA [11:2]
YC05
U18,
U19E
+5 V
Serial
Interface
CFCSM1, CFCSN2,
CFOEN1, CFWEN1,
CDET1A, CDET1B,
CFRST1, CFWAIT1
Option
memory card
(CompactFlash)
Serial
Driver
YC03
Parallel
Interface
CFD [15:0]
U20
+3.3 V
+5 V
Regulator
+5 V
U24
+3.3 V
4-26
+2.5 V
Regulator
+5 V
Regulator
U21
U28
+3.3 V
Regulator
YS01
CSN [1:0],
OEN0,
WEN0
U03-U05
ALATCH
CSN2,
OEN0,
WEN0
Image
chip
XLIDATA, SRCCLKN
ROMA [4:2]
LA [22:2]
Address
Latch
System
DIMM
[board]
LA [3:2]
CPUD [31:24]
CPUD [31:0]
CPUD [15:0]
U06-U07
CPUA [31:0]
U01
EXTBOEN,
EXTDIR
Buffers
CPU
PowerPC740
200 MHz
CPUD [31:0]
BCLK, BGN,
TAN, TEAN,
RSTOUTN, CPUINTN,
DBGN, AACKN
U08, U09S
ROMA1
LA [21:2]
LD [15:0]
X01
Xtal
50.0000 MHz
LA22,
LA [11:2]
YC06
Xtal
25.76930 MHz
YC04
U10, U11
SDA [12:0], SDBA [1:0]
Expanding
SDRAM
(DIMM)
Expanding
SDRAM
(DIMM)
U12-U15
U31
U22T
NAND
U17
2nd Optional
Interface
YC01
Engine
Board
EXTBOEN,
CFOEN1
Buffers
AND
YC07
KUIO
LD [15:0]
SDCLK, SDCKE,
SDCSN [5:0],
SDRAS, SDCAS,
SDWEN,
DQMUU, DQMUM,
DQMLM, DQMLL
IICSDA, IICSCL
KUIOCSN1
IORN1, IOWN1,
OPRDY1,
DMAACKN1
OPRST1,
IODTACKN1,
OPIRN1,
DMAREQ1
LA [16:2]
SDD [31:0]
SDRAM
YS03
CFCSN1, CFCSN2,
CFOEN2,
CFWEN2,
CDET2A, CDET2B,
CFRST2,
CFWAITN2
Option
hard disk
(Microdrive)
LD [15:0]
X02
YS02
CSN [3:2],
OEN1,
(WEN0)
FONTs
Centronics
Buffer
YC02
P1284HD,
ACK,
BUSY,
PERROR,
SELECT,
FAULT,
P1284DIR,
SELECTIN,
STROBE,
AUTOFD,
INIT,
P1284DIR
XTXD,
XDTR,
XRTS,
XDSR,
XCTS,
XRXD,
RSSEL
YC05
CFD [15:0]
U18,
U19E
+5 V
Serial
Driver
YC03
Serial
Interface
Parallel
Interface
CFCSM1, CFCSN2,
CFOEN1, CFWEN1,
CDET1A, CDET1B,
CFRST1, CFWAIT1
Option
memory card
(CompactFlash)
U20
+3.3 V
+5 V
Regulator
+5 V
U24
+3.3 V
U21
+2.5 V
Regulator
+5 V
Regulator
U28
+3.3 V
Regulator
4-27
Engine board
Eraser lamp
control
circuit
Sensor
board
Waste toner
full detection
circuit
ERASE
ERDEAD*
OPRDY*
WTNLED
WTONFUL*
Paper
gauge
sensing
circuit
PAPVOL
A8 - A17
CASIZE
ZCROSS
THERM
Power
supply
unit
FRCS*
CPU
(U201)
Engine
gate
array
(U204)
Flash
ROM
(U202)
5VSAVE* 5 V DC
power
saver
Thermisor
blown-out THDEAD*
detection
Abnormal
HTEMP*
temperature
detection
HEATON
circuit
SOOUT, SCLKOUT
SYSCLK
GAINT
Heater lamp
control circuit
RESET* Reset
IC
(U203)
AIRTEMP, AIRWET
RESET*
WETCK1, WETCK2
VSEREQ*
SIOUT
REGPAP, TCOVOP,
SCOVOP*,FCOVOP*,
HEATON*
FDPFUL*, EXITPAP*
Engine
relay
board
FDDR, FUDR
Driver
Driver
FDON, FUON
OPSCLK,
OPSDO
Controller
unit
fan motor
driver
circuit
FANON*
Cooling
fan motor
driver circuit
Controller
unit fan
motor
Bus
buffer
(U206)
OPTSDI
Option
unit
MMOTRDY*
Scanner
unit
OPSEL0-3
OPSEL3-4
FANSPD
Bus
buffer
(U207)
FPRST*
TMOTON
TNMOC
Toner motor
control
circuit
DLPTYPE, CONTYPE
TONSCAN
TNEMP*
MCHON, TRCHON, RTRCHON*,
TRVSEL1,TRVSEL2, TRVSEL3,
TRTCHON, HVCLK1, HVCLK2
HUNIT*, HANDS*
High
voltage
unit
OPSDI, OPRDY*
SYSRES*, SDIR,
VDFON1*, PDOUT*,
20PTRIG, SBSY*
EGIR, VDFON1*
SCLKIN, SOIN
FPCLK, FPDIR
FPDATA
+3.3V1
4-28
Main
board
Engine board
+24V
ERASE
3 Q214
+5V
R249
P40/SCK0
Drum board
A
YC203
9
2
GND
60 ERDEAD*
ERASEDR
ERASER
Q216
3
R251
1
GND
R252
GND
FS-1800/1800N | FS-3800/3800N
4-29
Engine board
+24V2
CPU
U204
1
Q218
15
TMOTON
3
TMOTON
3 Q217
R265
GND
1
2
Q220
YC203
16
R266
R267
TNMOC
17 TNMOC
DZ206
R268
GND
GND
FS-1800/1800N | FS-3800/3800N
4-30
TMOTDR
GND
Toner
motor
R219
3.3k
8
6
7
393
5 +
4 U205-2
+5V1
QA201B 4
5
HEATON*
Engine
gate
array
(U204)
3
3
HEATON 4
Q204
HEATON
1
1
QA201A
THERM
+5V1
CPU
(U201)
+5V1
HTEMP* 63
R233
1M
2
3 393
+
U205-1
1
THDEAD 54
P43/PPG3
P34/RT04
/HRQ
R228
1.3k
THERM 3
PC
P50/AN0
+5V1
Thermisor
Heater lamp
TRC
AC
Fuser board
Power supply unit
4-31
As change in temperature is detected by the thermistor, CPU U201 adjusts the voltage that is
resultant of change in temperature, given at pin #3 (THERM) to keep the temperature as constant as
possible. This voltage is used to continuously switch the fuser lamp on and off. If pin #4 (HEATON)
of the engine gate array U204 is H level, transistor Q204 (pin #2) turns on, the photo coupler (PC)
on the power supply unit turns on, and the triac (TRC) turns on, consequently the heater lamp is AC
powered and lights. The heater lamp continuously turns on and off to maintain the temperature on
the heater roller at approximately 185*1/200*2 C (Normal paper, A4), 175*1/190*2 C (Thin paper,
A4), and 190*1/205*2 C (Thick paper, A4) for printing and approximately 95 C at standby (Ready).
Refer to section Fusing on page 4-15. *1: FS-1800/1800N *2: FS-3800/3800N
Abnormal temperature detection circuit
The thermal cutout device which is connected in series with the heater lamp, constitutes the the
abnormal temperature detection circuit including of comparators U205-2, R217, R219, etc. Pin #5
of the comparator U205-2 is continuously given with the voltage by resistors R217 and R219,
which simulate the voltage given if an abnormally high temperature develops. Pin #6 receives the
voltage the thermistor detects. For instance, the heater lamp happens not to switch off, the voltage
the thermistor gives at pin #6 will become unusually high, and as soon as it exceeds the voltage at
pin #5, pin #7 of the comparator U205-2 output changes to L level. This in turn turns transistors
QA201B and QA201A on, and turns QA201A (pin #6) to L level. Since pins #6 of the transistor
QA201A and #2 of transistor Q204 are connected to each other, pin #4 of the engine gate array
U204, even though it is currently at H level, is enforced to be H level, effectively disabling the
heater lamp. Pin #7, the output from comparator U205-2, changes to L. Then, it is output to #63 of
CPU (U201) which in turn determines that an unusual temperature has developed in the fuser,
indicating Call service personE4.
Thermistor blown-out detection
The thermistor is monitored by the combination of comparator U205-1, R233, and R238. Extremely
low potential is applied to pin #3 of U205-1 by means of R233 and R238. Whereas, pin #2 is
applied with the voltage the thermistor detects. In normal state, as the heater lamp glows, the voltage
detected by the thermistor is greater than the potential at #3 of U205-1, making the U205-1 output
to L and sent to #54 (THDEAD) of CPU.
When the thermistor has blown, pin #2 of U205-1 becomes zero which is well lower than the
potential at pin #3 of U205-1, the comparator output becomes H, delivering THDEAD at pin #54 of
CPU. CPU uses this signal to determine that the thermistor is faulty and displays Call service
personE4.
FS-1800/1800N | FS-3800/3800N
4-32
Sensor board
Paper gauge
sensor 1 (PH702)
Paper gauge
sensor 2 (PH703)
Acutuator
(Reflecting mirror)
Paper
gauge
Actuator
position
Sensing input
D/A converted
output
PH702
PH703
Empty
approximately
5V
1/4 to 1/2
approximately
2.25 V
1/2 to 3/4
approximately
1.95 V
3/4 to full
approximately
3.9 V
PH702
PH703
FS-1800/1800N | FS-3800/3800N
4-33
Interlock circuit
The interlock circuit is constituted by SW702, the top cover/paper feed unit interlock, and SW703,
the side cover interlock, both mounted on the sensor board. These switches are controlled by the
actuator which is mechanically activated by the projection on the top cover and the feed unit.
SW703 and SW702 are connected in series to the +24 V power. Physically opening the top cover,
side cover, or the paper feed unit will disconnect the +24 V power, signaling the status to the engine
board. The top cover switch (SW701) serves only the top cover.
Top cover
Projection
Side cover
interlock
switch
(SW703)
Sensor board
Actuator
Projection
Side cover
Top cover/
feed unit
interlock
switch
(SW702)
Projection
FS-1800/1800N | FS-3800/3800N
4-34
The interlock circuit outputs the three different detection signals which are combined in matrix to
produce various levels of situations regarding the covers. The subsequent status is displayed on the
message display.
Engine board
+24V1
Top cover
Actuator
N.O.
Top cover/
paper feed
unit interlock
switch (SW702)
N.C.
+5V2
COM
Side cover
Top cover
switch (SW701)
COM
GND
GND
Engine
gate
array
(U204)
+24V2
N.O.
GND
GND
Output level
Operator panel message display
Ready
Top cover open
Top cover open
Top cover open
Top cover open
Feed open
Feed open
Side cover open
Feed
Side
Feed
Side
open
cover open
open
cover open
H
L
L
L
L
L
L
L
L
H
H
H
H
L
L
L
H
L
L
L
L
L
L
H
FS-1800/1800N | FS-3800/3800N
4-35
Paper size
switch
Cassette
FS-1800/1800N | FS-3800/3800N
4-36
The paper size dial has predetermined patterns of activating the paper size switches using concaves
and convexes according to paper sizes. SW1, SW2, and SW3 produce corresponding signals for
paper sizes. These patterns are translated into analog voltages and sent to the engine board on a
single line. The signals are analog-digital-converted on the engine board.
Sensor board
+24V1
R704
GND
R702
DZ70
R703
R701
SW1
Engine board
SW2
SW3
CPU
(U204)
Paper size switch
C246
GND
R238
Paper cassette
GND
Paper size
Cassette
not
installed
Other
Legal
A4
A5
B5
See
note
below.
SW1
Off
Off
Off
On
On
On
On
SW2
Off
Off
On
Off
Off
On
On
Concave
(Function Off)
SW3
Off
On
Off
Off
On
Off
On
Convex
(Function On)
D/A converted
output voltage
0V
FS-1800/1800N | FS-3800/3800N
4-37
Power Current
switch fuse
SLEEP*
Noise
filter
circuit
Rectifier
circuit
Transformer
FET
Heater
lamp
Thermal
cutout
+24V1
Enargysaving
circuit
Switching
control
circuit
Zero cross
signal
generation
circuit
24 V DC
rectifier/
smoothing
circuit
Over
voltage/
current
detection
circuit
5 V DC
rectifier/
smoothing
circuit
GND
+5V1
GND
Photocoupler
Photocoupler
ZCROSS
PhotoTriac
HEATON*
Triac
THERM
FDFUL
EXITPAP*
FDDR
FUDR
Thermistor
+5V1
Paper full
sensor
+24V
Fuser
board
Exit sensor
FS-1800/1800N | FS-3800/3800N
4-38
Face up/down
solenoid
+24V2
Developer
(Magnet roller)
Control
and
driver
circuit
RTRCHON*
MCHON*
TRCHON*
TRVSEL3*
TRVSEL2*
TRVSEL1*
Control
and
driver
circuit
HVCLK
Driver
circuit
Transfer bias
output
positive voltage
circuit
Transfer roller
Rectifier
circuit
GND
PGND
Sensor circuit
+5V2
MP tray
HUNIT*
Option
feeder
sensor
MP tray
paper
sensor
HANDS*
Paper
FS-1800/1800N | FS-3800/3800N
4-39
Chapter 5
D i s a s s e m b l y
Chapter 5 Contents
5-1 General instructions ........................................................................................................................ 5-3
5-1-1 Screw/hardware ......................................................................................................................... 5-3
5-1-2 Before starting disassembly ...................................................................................................... 5-3
5-2 Disassembly ..................................................................................................................................... 5-4
5-2-1 Removing the developer ............................................................................................................ 5-4
(1) Removing the developer ............................................................................................................ 5-4
5-2-2 Removing the paper feed unit ................................................................................................... 5-6
5-2-3 Removing the main charger unit ................................................................................................ 5-7
5-2-4 Removing the operator panel and outer covers ........................................................................ 5-8
(1) Removing the operator panel .................................................................................................... 5-8
(2) Removing the top cover/face-down output tray ......................................................................... 5-9
(3) Removing the right cover ......................................................................................................... 5-10
(4) Removing the left cover ........................................................................................................... 5-11
5-2-5 Removing the drum unit .......................................................................................................... 5-12
5-2-6 Removing the pickup roller and feed roller .............................................................................. 5-13
5-2-7 Removing the MP paper feed unit ........................................................................................... 5-15
5-2-8 Removing the transfer roller .................................................................................................... 5-17
5-2-9 Removing the controller unit and the principal circuit boards .................................................. 5-18
(1) Removing and opening the controller unit ............................................................................... 5-18
(2) Removing the engine board and power supply unit ................................................................ 5-22
(3) Removing the main board ....................................................................................................... 5-24
(4) Removing the high voltage unit ............................................................................................... 5-25
(5) Removing the sensor board .................................................................................................... 5-26
5-2-10 Removing the drive unit and main motor ............................................................................... 5-27
5-2-11 Removing and splitting the fuser unit .................................................................................... 5-29
(1) Removing the separators ........................................................................................................ 5-32
(2) Removing the heater lamp ...................................................................................................... 5-33
(3) Removing the heat roller ......................................................................................................... 5-34
(4) Removing the thermistor and the thermal cutout ..................................................................... 5-35
(5) Removing the press roller ........................................................................................................ 5-36
5-2-12 Removing the laser scanner unit ........................................................................................... 5-37
To avoid injury caused by electric shock, make sure that AC power is removed
and the power cord is unplugged from both the power line and the printer.
5-1-1 Screw/hardware
Screws and hardware used in the printer are listed in the Ecosys Screw catalog. These screw symbol
numbers are universal to most Ecosys printers.
CAUTION
When securing a self-tapping screws, align it with the thread carefully. First turn
it counterclockwise, then slowly clockwise. Do not overtighten. In case the selftapped thread is damaged, the whole part may have to be replaced with a new
part.
CAUTION
The printer use electrostatic sensitive parts inside (circuit boards, laser scanner
unit, etc.). Provide an antistatic (discharging) device, such as a wrist strap, that
can effectively discharge your body before touching those components.
FS-1800/1800N | FS-3800/3800N
5-3
5-2 Disassembly
5-2-1 Removing the developer
(1) Removing the developer
CAUTION
When if installing or removing the developer, do not let the magnet roller touch
any part in the printer.
When handling developer, use both hands. Do not press the bottom of the
developer.
1
2
NOTE
After removing the developer, seal it in the protective bag and place it on a flat
surface. Do not place the developer in a dusty area. If you ship the developer,
pack it in the shipping container specifically supplied with the printer. See section
Shipping the developer on page 3-13. Also do not touch the developing roller 5.
Do not place floppy disks near the developer.
FS-1800/1800N | FS-3800/3800N
5-5
FS-1800/1800N | FS-3800/3800N
5-6
FS-1800/1800N | FS-3800/3800N
5-7
3
4
3
FS-1800/1800N | FS-3800/3800N
5-8
FS-1800/1800N | FS-3800/3800N
5-9
1
1
1
2
2
2
3
FS-1800/1800N | FS-3800/3800N
5-10
1
1
1
FS-1800/1800N | FS-3800/3800N
5-11
1
2
FS-1800/1800N | FS-3800/3800N
5-12
B
3
2
FS-1800/1800N | FS-3800/3800N
5-13
4
5
Pickup gear Z32S 8 is installed of the inside the one way clutch 9. When
refitting pickup gear Z32S 8, face the one way clutch 9 face to the feed bracket
cover 4.
FS-1800/1800N | FS-3800/3800N
5-14
FS-1800/1800N | FS-3800/3800N
5-15
5. Pull the MP tray paper feed unit 4 out while unlatching two latches 5 off of points A.
5
4
FS-1800/1800N | FS-3800/3800N
5-16
Do not touch the transfer roller 1 (sponge) surface. Oil and dust (particles of
paper, etc.) on the transfer roller 1 can significantly deteriorate the print quality
(white spots, etc.).
1
2
FS-1800/1800N | FS-3800/3800N
5-17
5-2-9 Removing the controller unit and the principal circuit boards
(1) Removing and opening the controller unit
1. Remove the top cover/face-down output tray. See page 5-9.
2. Remove the right and left covers. See page 5-10 and 5-11.
3. Remove the four connectors 1 from the controller unit 2 left side.
CAUTION
Draw the connector straight to remove. If you draw the connector while it is
slanted, the receptacle may be damaged.
1
2
Receptacle
Connector
Figure 5-2-15 Removing the connectors from controller unit left side
FS-1800/1800N | FS-3800/3800N
5-18
4. Remove the two connectors 3 from the controller unit 2 right side.
Receptacle
Connector
Figure 5-2-16 Removing the connectors from controller unit right side
FS-1800/1800N | FS-3800/3800N
5-19
4
4
Figure 5-2-17 Removing the controller unit form the frame unit
FS-1800/1800N | FS-3800/3800N
5-20
8
8
9
8
FS-1800/1800N | FS-3800/3800N
5-21
3
1
1
3
2
FS-1800/1800N | FS-3800/3800N
5-22
6
5
8
4
Before removing the main board, the memory card must be removed first.
However, do not remove the memory card while power is on. If the memory card
is removed (or inserted) while the printer is on, damage could result in the printers
electronics as well as the memory card.
2
2
FS-1800/1800N | FS-3800/3800N
5-24
FS-1800/1800N | FS-3800/3800N
5-25
Draw the connector straight to remove. If you draw the connector while it is
slanted, the receptacle may be damaged.
3
A
Connector
1
Receptacle
Connector
Receptacle
Draw the connector straight to remove. If you draw the connector while it is
slanted, the receptacle may be damaged.
1. Remove the paper cassette and the feed unit. See page 5-6.
2. Remove the top cover/face-down output tray. See page 5-9.
3. Remove the left and right covers. See pages 5-10 and 5-11.
4. Remove two connectors 1.
5. Remove three connectors 2 of the drive unit 3.
6. Remove five screws 4 and the ground wire terminal 5.
7. Remove the drive unit 3 from the frame unit.
Connector
Receptacle
Connector
Receptacle
4
Figure 5-2-24 Removing drive unit
FS-1800/1800N | FS-3800/3800N
5-27
FS-1800/1800N | FS-3800/3800N
5-28
The fuser unit is hot after the printer was running. Wait until it cools down.
1
2
1
Figure 5-2-26 Removing the fuser unit
FS-1800/1800N | FS-3800/3800N
5-29
5
4
6
8
FS-1800/1800N | FS-3800/3800N
5-30
0
9
FS-1800/1800N | FS-3800/3800N
5-31
The separators are extremely hot immediately after the printer was running. Allow
substantial period of time until it cools down.
2
Step 1
Step 2
FS-1800/1800N | FS-3800/3800N
5-32
The heater lamp is extremely hot immediately after the printer was running. Allow
substantial period of time until it cools down.
CAUTION
The heater lamps are fragile. Use extreme care when handling not to drop or
break.
Do not directly touch on the heater lamp. Finger prints on the heater lamps outer
surface can prevent proper fusing of toner on paper. When holding the heater
lamp, hold the ceramic parts of heater lamp at both ends.
When refitting the heater lamp, direct the wattage making side facing the gear
side.
1. Remove and split the fuser unit. See page 5-29.
2. Remove the lamp support 1.
3. Remove one screw 2 then remove the lamp holder 3.
4. Remove the heater lamp 4 from the heat roller 5.
Gear
Wattage marking
2
4
5
3
The heat roller is extremely hot immediately after the printer was running. Allow
a substantial period of time until it cools down.
: FS-1800/1800N
*2
: FS-3800/3800N
3
1
3
4
5
6
7
FS-1800/1800N | FS-3800/3800N
5-35
The press roller is extremely hot immediately after the printer was running. Allow
substantial period of time until it cools down.
FS-1800/1800N | FS-3800/3800N
5-36
3
Order of fixing the laser scanner unit
4
1
3
CAUTION
When refitting the laser scanner unit, fix the four screws in the order indicated
above.
Figure 5-2-34 Removing the laser scanner unit
FS-1800/1800N | FS-3800/3800N
5-37
Chapter 6
Troubleshooting
Chapter 6 Contents
6-1 Troubleshooting ............................................................................................................................... 6-4
6-1-1 General error handling ............................................................................................................... 6-4
(1) Maintenance messages ............................................................................................................. 6-4
(2) Error messages ......................................................................................................................... 6-7
6-1-2 Diagnostic (Service error messages) ...................................................................................... 6-11
(1) A0 Zero cross signal error .................................................................................................... 6-12
(2) A2 Abnomal high temperature error ..................................................................................... 6-12
(3) B2 Option paper feeder PF-60 (Top) paper feed motor error .............................................. 6-13
(4) B3 Option paper feeder PF-60 (Middle) paper feed motor error .......................................... 6-13
(5) B4 Option paper feeder PF-60 (Bottom) paper feed motor error ....................................... 6-13
(6) C0 Option paper feeder PF-60 communication error ........................................................... 6-14
(7) C1 Option duplexer DU-60 communication error ................................................................. 6-14
(8) C2 Option duplexer DU-60 side registration error................................................................ 6-14
(9) C4 Option sorter SO-60 communication error ..................................................................... 6-15
(10) CE Option bulk paper feeder PF-8E motor error ............................................................... 6-16
(11) CF Option bulk paper stacker HS-8E motor error .............................................................. 6-16
(12) E0 Communication error .................................................................................................... 6-16
(13) E1 Main motor error ........................................................................................................... 6-17
(14) E2 Laser scanner unit (Polygon motor) error ..................................................................... 6-18
(15) E3 Laser scanner unit (Pin photo diode sensor) error ....................................................... 6-19
(16) E4 Fuser unit error ............................................................................................................. 6-20
(17) E5 Eraser lamp error .......................................................................................................... 6-21
(18) E9 Toner motor error ......................................................................................................... 6-22
(19) ED Flash ROM error .......................................................................................................... 6-23
(20) F0 LCD controller board error ............................................................................................ 6-23
(21) F1 System DIMM [board] error .......................................................................................... 6-23
(22) F2 Main or expanded memory error .................................................................................. 6-24
(23) F3 General failure .............................................................................................................. 6-24
(24) 99 Toner refreshing mode error ......................................................................................... 6-24
6-1-3 Other problems ........................................................................................................................ 6-25
(1) False Paper feed unit Open .................................................................................................. 6-25
(2) False Top cover Open ........................................................................................................... 6-25
(3) False Side cover Open .......................................................................................................... 6-26
(4) Defective waste toner bottle detecting ..................................................................................... 6-26
(5) Defective paper jam detecting ................................................................................................. 6-27
(6) Defective paper gauge sensing ............................................................................................... 6-27
(7) Defective paper size detecting ................................................................................................ 6-27
(8) Defective message displaying (LCD) ...................................................................................... 6-28
(9) Defective face up/down solenoid operating ............................................................................. 6-29
6-30
6-30
6-36
6-37
6-38
6-39
6-40
6-41
6-41
6-42
6-43
6-44
6-45
6-46
6-47
6-48
6-48
6-49
6-1 Troubleshooting
6-1-1 General error handling
(1) Maintenance messages
Message
Add paper
(paper source)
Check waste
toner bottle
Clean printer
Press GO
Duplexer
rear cover open
Face-down tray
paper full
Corrective action
The paper has run out. Supply paper according to the paper source
displayed (paper cassette, MP tray, or option paper feeder).
Messages indicating the printer status (Ready , Please wait
Processing *, Waiting, and FormFeed Time Out *) are
displayed alternately.
* These messages will not appear if the number of copies is set to
2 or more.
The waste toner bottle is not installed. Replace the old waste toner
bottle with the new one which is included in the TK-60/TK-60E
toner kit. The message will also be shown if the waste toner bottle
has become full. The waste toner bottle should be replaced when
the message display eventually shows Toner low TK-60. See
section Toner container replacement on page 3-5.
Clean the inside of the printer, according to section 3-1-3 Cleaning
the printer on page 3-8. This message will be displayed when
replacing the toner container after the message Replace toner
TK-60 has been displayed. After cleaning the inside of the printer,
press the GO key and the printer will be ready for printing. If
Auto Continue is set to On, printing will be automatically resumed
after a preset period of time.
Open the option duplexer rear cover, then close tightly.
The face-down output tray has become full (approximately 250
pages). Remove all printed pages from the face-down output tray.
When the printer senses that the face-down output tray is empty
again, it will continue printing into the face-down output tray.
: Alarm buzzer sounds when an error occurs. Press the CANCEL key to stop the alarm buzzer.
FS-1800/1800N | FS-3800/3800N
6-4
Message
Load Cassette #
(paper size)/(paper type)*
Corrective action
Paper whose size watches the size embedded in a print job is empty.
Set paper into the paper source as displayed on the operator panel,
and press the GO key to restart printing. The paper source number
*(paper size) and (paper type) (#) is only displayed when there is an optional paper feeder installed.
are displayed flashing
If you want to print from an alternative paper source press the
alternately.
key or key to display Use alternative? and you can change
to another paper source. Further, you can change the paper source
by pressing the GO key.
After selecting a paper source and pressing the MENU key, Paper
handling > appears. By pressing the > key, the paper type setting
menu appears. After setting the correct paper type, press the ENTER
key and printing starts.
Load MP tray
There is no paper cassette (paper size and paper type) that matches
(paper size)/(paper type)
the size embedded in a print job. Printing is done from the MP tray.
Set paper into the MP tray that matches the paper size and type
*(paper size) and (paper
shown on the display and press the GO key to restart printing.
type) are displayed flashing
If you want to print from an alternative paper source, press the or
alternately.
key to display Use alternative? and you can change to
Missing duplex
drawer
Opt.Stacker unit
rear cover open
Option interface
another paper source. Further, you can change the paper source by
pressing the GO key.
After selecting a paper source and pressing the MENU key, Paper
Handling > appears. By pressing the > key, the paper type setting
menu appears. After setting the correct paper type, press the ENTER
key and printing starts.
The duplex drawer is either not installed or incorrectly inserted.
Insert the duplex drawer securely.
Open the sorter rear cover, then close tightly.
FS-1800/1800N | FS-3800/3800N
6-5
Message
Option tray ##
paper full
Corrective action
The sorter tray indicated by # is now full. Remove the paper from
the tray.
Remove paper
option tray ##
Replace toner
Clean printer
Side cover
Open
Toner low
TK-60
Top cover
Open
Warning
image adapt
Warning
Low memory
Open the top cover or the paper feed unit and correct the paper jam
(or paper mis-feeding in the cassette). The location of the paper jam
is also indicated in place of the # 's. On-line help messages which
are useful for correcting the paper jam will be displayed by pressing
key. See section 6-1-7 Correcting a Paper Jam on page 6the
48.
There is still paper in the option sorter's tray indicated by # when the
power was turned on or the sorters mode was switched. Remove
all the paper inside the sorter.
Replace the toner container using a new toner kit. The printer does
not operate when this message is displayed. See section Toner
container replacement on page 3-5.
Open the side cover, then close tightly.
Replace the toner container using a new toner kit. See section Toner
container replacement on page 3-5.
Open the top cover, then close tightly.
FS-1800/1800N | FS-3800/3800N
6-6
Corrective action
6-7
Message
Hard disk error##
Press GO
I/F occupied
ID error
Insert the same
memory card
KPDL Error
Press GO
##
Corrective action
10 : Formatting is not possible because host data is being spooled on
the hard disk (Microdrive). Wait until the hard disk is ready, and then
format.
85 : VMB; Alias error (The alias setting was lost, or the VMB tray
corresponding to the alias does not exist.) Set alias again.
97 : Code job; The number of permanent code job reached the limit
value, and no more can be saved. Either delete some unnecessary jobs,
etc., or increase the limit.
99 : A print job for the specified ID does not exist in the hard disk
(Microdrive).
This message is displayed when you attempt to use the printer's operator
panel to change the environmental settings on the interface from which
data are presently being received.
The ID entered for a private job, or a stored job is not correct. Check
the ID that is set using the printer driver.
You have inserted a wrong memory card (CompactFlash) when the
Insert again message was displayed. Remove the wrong memory
card from the printer's memory card slot and insert the correct memory
card. The printer again reads it from the beginning of the data.
PostScript error has occurred and current print processing cannot
continue. To print out an error report, display > Print KPDL errs
from the menu selection system, and select On. Press the GO key to
resume printing. You can abandon printing by the CANCEL key.
If Auto Continue is set to On, printing will be automatically resumed
after a preset period of time. Refer to printers Users Manual.
The memory card (CompactFlash) is accidentally removed from the
printer's memory card slot during reading. If you continue reading the
memory card, insert the same memory card into the slot again. The
printer again reads it from the beginning of the data.
Note: We recommend that you follow the reading procedure from the
beginning to ensure correct reading of the memory card.
: Alarm buzzer sounds when an error occurs. Press the CANCEL key to stop the alarm buzzer.
FS-1800/1800N | FS-3800/3800N
6-8
Message
Memory overflow
Press GO
Corrective action
The total amount of data received by the printer exceeds the printers
internal memory. Try adding more memory (expansion DIMM). Press
the GO key to resume printing. You can abandon printing by the
CANCEL key. If Auto Continue is set to On, printing will be
automatically resumed after a preset period of time. Refer to printers
Users Manual.
MemoryCard err##
This message appears when an error occurred during access to the
Press GO
memory card (CompactFlash) using the PRESCRIBE 2e RWER
command or from the printer's operator panel. Look at the error code
given in place of ## and refer to the corresponding description given
below:
01 : The memory card (CompactFlash) does not meet the requirement.
This memory card cannot be used by this printer. Insert a memory
card which complies with the requirements. (See section 1-1-2
Available option memory/device on page 1-6.)
02 : The memory card is not installed. Check the requirements for
using the memory card.
04 : The capacity of the memory card is insufficient. Clean up files.
05 : Specified file not found on the memory card.
06 : Insufficient printer memory to support a memory card. Expand
printer memory.
Paper path error
There is no cassette in the feeder, or the cassette is not inserted
properly. When two or more option feeders are installed and the lowest
one is selected, the same message will appear if any of the upper
feeder cassettes and the printer cassette is improperly installed.
The data transferred to the printer was too complex to print on a page.
Print overrun
Press the GO key to resume printing. (The page may break in some
Press GO
pages.) You can abandon printing by the CANCEL key.
Note: After this message has been displayed, Page protect mode will
be On. To maintain optimum use of memory during printing, display
>Page protect from the operator panel, and re-select Auto. Refer
to printers Users Manual.
If Auto Continue is set to On, printing will be automatically resumed
after a preset period of time. Refer to printers Users Manual.
: Alarm buzzer sounds when an error occurs. Press the CANCEL key to stop the alarm buzzer.
FS-1800/1800N | FS-3800/3800N
6-9
Message
RAM disk error ##
Press GO
Corrective action
FS-1800/1800N | FS-3800/3800N
6-10
Call service
personDn
Call service
personEn:0123456
Call service
personFn
Call service
person99
Meaning
Fuser error (n=0, 2). The total number of pages printed follows. Follow
the appropriate instructions provided in the following sections.
Option paper feeder error (n=2 to 4). The total number of pages printed
follows. This message pertains to option paper feeder PF-60. Follow
the appropriate instructions provided in the following.
Option equipment error (n=0 to 4, 7, E and F). The total number of
pages printed follows. This message pertains to paper feeder PF-60,
sorter SO-60, and duplexer DU-60. Follow the appropriate instructions
provided in the follow sections.
Engine firmware download error (n=0 to 3). See section 3-1-4 Updating
the firmware on page 3-15.
Mechanical error (n=0 to 5, 9 and D). The total number of pages printed
follows. Follow the appropriate instructions provided in the following
section.
Controller error (n=0 to 3). Follow the appropriate instructions provided
in the following sections.
Toner refreshing mode error. Follow the appropriate instruction provided
in the following sections.
FS-1800/1800N | FS-3800/3800N
6-11
Corrective action
Replace power supply
unit. See page 5-22.
Replace engine board. See
page 5-22.
Suggested causes
Corrective action
Call service
personA2:0123456
Turn power switch off.
CAUTION:
Fuser unit is fed directly by AC
power from primary circuit on power
supply board.
Be careful with electricshock.
More
than 3 V DC over 3
seconds?
NOTE:
If the problem is not solved by
this flow chart replace, the
following items:
No
Replace engine board
(KP-864). See page 5-22.
Yes
FS-1800/1800N | FS-3800/3800N
6-12
(3) B2 Option paper feeder PF-60 (Top) paper feed motor error
Meaning
Suggested causes
Paper feed motor error Defective gate array U204 on the engine
board (KP-864).
in the top option paper
Defective harness (S02400) between engine
feeder.
board and option unit interface connector.
Defective paper feeder PF-60.
Corrective action
Replace engine board
(KP-864). See page 5-22.
Replace harness (S02400).
Refer to option paper
feeder PF-60s Service
Manual.
(4) B3 Option paper feeder PF-60 (Middle) paper feed motor error
Meaning
Suggested causes
Paper feed motor error Defective gate array U204 on the engine
board (KP-864).
in the middle option
Defective harness (S02400) between engine
paper feeder.
board and option unit interface connector.
Defective option paper feeder PF-60.
Corrective action
Replace engine board (KP864). See page 5-22.
Replace harness (S02400).
Refer to option paper
feeder PF-60s Service
Manual.
(5) B4 Option paper feeder PF-60 (Bottom) paper feed motor error
Meaning
Suggested causes
Paper feed motor error Defective gate array U204 on the engine board
in the bottom option
(KP-864).
paper feeder.
Defective harness (S02400) between engine
board and option unit interface connector.
Defective paper feeder PF-60.
Corrective action
Replace engine board (KP864). See page 5-22.
Replace harness (S02400).
Refer to option paper
feeder PF-60s Service
Manual.
FS-1800/1800N | FS-3800/3800N
6-13
*1
Corrective action
Replace engine board (KP864). See page 5-22.
Follow installation
instruction carefully again.
Replace harness (S02400).
Remedy.
Refer to option paper
feeder PF-60s Service
Manual.
: FS-1800/1800N
*2
: FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
6-14
Corrective action
Replace engine board (KP864). See page 5-22.
Follow installation
instruction carefully again.
Replace harness (S02400).
Remedy.
Refer to option duplexer
DU-60s Service Manual.
: FS-1800/1800N
*2
: FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
6-15
Suggested causes
Corrective action
Defective harness (S02400) between engine Replace engine board (KPboard and option unit interface connector. 864). See page 5-22.
Defective option bulk paper feeder.
Replace harness (S02400).
Suggested causes
Corrective action
Defective harness (S02400) between engine Replace engine board (KPboard and option unit interface connector. 864). See page 5-22.
Defective option bulk paper stacker HS-8E. Replace harness (S02400).
Suggested causes
Corrective action
Defective gate array (U02) on the main board. Replace the main board
(KP-777*1/KP-858*2). See
page 5-24.
Connector failure between the engine board V e r i f y c o n n e c t o r
(KP-864) and main board (KP-777*1/KP- connections.
858*2).
Overrun in the engine system, deactivating Replace the engine board
the program flash ROM (U202) on the (KP-864). See page 5-22.
engine board (KP-864).
*1
FS-1800/1800N | FS-3800/3800N
6-16
: FS-1800/1800N
*2
: FS-3800/3800N
Suggested causes
Corrective action
Overcurrent in the main motor circuitry due Follow the flow chart
to an excessive torque.
below.
Connector insertion error.
Defective gate array U204 on the engine
board (KP-864).
Defective harness between engine board and
engine relay board (KP-760).
Defective harness between engine relay board
(KP-760) and main motor.
Call service
personE1:0123456
Turn power switch off.
Remove and check
harness (S02405)
between engine board
(KP-864) and engine
relaly board (KP-760),
or harness (S02401)
between engine board
(KP864) and main
motor.
Does
pin #3 (MMOTON*)
of YC802 on engine board
(KP-864) goes high,
then low?
Yes
No
OK?
Yes
Turn power switch on.
+24 V DC
at #1 pin of YC802
on engine board
(KP-864) ?
No
No
Replace engine relay board
(KP-760). See page 5-15.
Yes
Does pin
#7 (MMOTRDY*)
of YC802 on engine board
goes low, after pin #3
(MMOTON*) of
YC802 goes
low?
Yes
No
NOTE:
If the problem is not solved by this flow
chart replace the following items:
Harness (S02401) between engine
relay board (KP-760) and engine
board (KP-864)
Drive unit (See page 5-27.)
FS-1800/1800N | FS-3800/3800N
6-17
Suggested causes
Corrective action
Defective gate array U204 on the engine Follow the flow chart
board.
below.
Defective polygon motor.
Improper connector insertion.
Defective harness between laser scanner unit
and engine board.
Call service
personE2:01234546
NOTE:
Pins of YC206 connector are
crowded and tiny. When if
measuring signal, contact
measurement probe with pins of
YC206 connector accurately.
No
OK?
Does
pin #31 (POLON*) of
YC206 on engine board
(KP-864) goes high and
then low?
No
Yes
Replace harness between
engine board (KP-864)
and laser scanner unit.
Yes
Turn power switch on.
+24 V DC
at #33 pin of YC206
on engine board
(KP-864) ? Yes
Does pin
#30 (POLRDY*)
of YC206 on engine board
goes low, after pin #31
(POLON*) of YC206
goes low?
No
No
Yes
Print status page.
Replace engine board
(KP-864). See page 5-22.
Does
pin #1 (POLCLK) of
YC206 on engine board
(KP-864) output
square-wave*1
signal?
No
Replace laser scanner
unit. See page 5-37.
Yes
*1: [FS-1800/1800N]
2,298 Hz
[FS-3800/3800N]
2,314.93 Hz
NOTE:
When If not solved this flow chart,
try to replace below items.
Harness (S02404) scanner unit
and engine board (KP-864)
Engine board (KP-864) and scanner
unit (replace at the same time)
FS-1800/1800N | FS-3800/3800N
6-18
Suggested causes
Corrective action
No laser beam due to the laser diode defect Follow the flow chart
below.
(PD*).
Soiled or defective pin photo diode sensor.
Defective gate array U204 of engine board.
Improper connector insertion.
Defective harness between engine board and
laser scanner unit.
Call service
personE3:0123456
*1: Pin photo diode sensor
[board KP-746] detecting
horizontal synchronization signal
[FS-1800/1800N]
Frequency: 2.3 kHz,
Low level width: 1.4 s
[FS-3800/3800N]
Frequency: 3.5 kHz,
Low level width: 1.0 s
+24 V DC
at #1 pin of YC601
on APC board
(KP-742) ?
No
Pin #8 (_PDIN*)
of YC601 on APC board
(KP-742) output pulse
signal*1 ?
No
Yes
Replace engine board
(KP-864). See page 5-22.
Yes
Print status page.
Replace laser scanner
unit. See page 5-37.
Does
pin #4 (LASER*) of
YC601 on APC board
(KP-742) goes high and
then low?
Yes
No
NOTE:
If the problem is not solved by
this flow chart replace the
following items:
Harness (S02404) scanner unit
and engine board (KP-864)
Engine board (KP-864) and scanner
unit (replace at the same time)
FS-1800/1800N | FS-3800/3800N
6-19
Suggested causes
Corrective action
Blown-out thermistor.
Follow the flow chart
Blown-out heater lamp.
below.
Defective CPU U201 or comparator U205 on
the engine board.
Improper connector insertion.
Defective power supply unit.
Defective harness between fuser unit and
power supply unit.
*1: FS-1800/1800N *2: FS-3800/3800N
Call service
personE4:0123456
Turn power switch off.
Remove and check
harness (S02415)
between fuser board
(KP-756) and power
supply unit, or
thermistor connector
(YC834) on the
fuser board (KP-756).
CAUTION:
Fuser unit is fed directly by AC
power from primary circuit on power
supply board.
Be careful with electricshock.
Fuser unit is extremely hot
immediately after the printer was
running. Allow substantial period of
time until it cools down.
No
OK?
No
Open (infinite)?
Yes
Yes
Turn power switch on.
0 V DC
Yes
at pin #6 (THERM)
of YC831 on fuser board
(KP-756) ?
"E4"
shown?
No
Yes
Detach connector CN2
A on power supply
board. See figure right.
A
Measure resistance
between pins 1 and 3
of the detached
connector.
Heater lamp
End.
FS-1800/1800N | FS-3800/3800N
6-20
Call service
personE5:0123456
Measure voltage #1 pin
(ERASEDR*) of sensor
board (KP-754).
Approximately
0 V DC?
Yes
No
No
OK?
Approximately
14 to 15.5 V DC?
Yes
Remove and check
harness (S02412)
between drum board
(KP-748) and eraser
lamp [board KP762].
No
Approximately
24 V DC?
Yes
No
OK?
No
Yes
Deformed ?
Yes
No
Turn power switch on
and print starus page.
Replacedrum
drumunit.
unit.
Replace
Seepage
page5-12.
5-12.
See
NOTE:
If the problem is not solved by
this flow chart replace the
following items:
Engine board (KP864)
Sensor board (KP754)
Drum unit
FS-1800/1800N | FS-3800/3800N
6-21
Suggested causes
Corrective action
Overcurrent in the toner motor circuitry due Follow the flow chart
to an excessive torque, caused by hardened below.
toner.
Defective gate array U204 on the engine
board.
Improper connector insertion.
Defective harness between developer and
high voltage unit.
Defective harness between high voltage unit
and engine board.
Call service
personE9:0123456
"E9"
shown?
Yes
No
End.
NOTE:
If the problem is not solved by
this flow chart, replace the
following items:
High voltage unit
Harness (S02416) [Between developer and high voltage unit]
Harness (S02416) [Between engine board and high voltage unit]
FS-1800/1800N | FS-3800/3800N
6-22
Corrective action
Replace system DIMM
[board KP-710 *1 /KP689*2] or main board (KP777*1/KP-858*2).
Replace LCD controller
board (KP-738).
: FS-1800/1800N
*2
: FS-3800/3800N
Corrective action
: FS-1800/1800N
*2
: FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
6-23
Corrective action
Replace main board (KP777*1/KP-858*2).
Replace expanding
memory (DIMM).
: FS-1800/1800N
*2
: FS-3800/3800N
Suggested causes
Corrective action
F2, above.
*1
: FS-1800/1800N
*2
: FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
6-24
Corrective action
Replace high voltage unit.
See page 5-25.
Refer to section Toner
refreshing mode on page 322.
When
paper feed unit
close scurely, does pin
#12 voltage change
0 to 24 V
DC?
Yes
No
When
paper feed unit
close scurely, does pin
#20 voltage change
0 to 24 V
DC?
Yes
No
When
Top cover
close scurely, does pin
#11 goes low
to high?
Yes
No
FS-1800/1800N | FS-3800/3800N
6-25
False
"Side cover Open"
When
Side cover
close scurely, Do pins
#5, #6 and #7 voltage
change 0 to 24 V
DC?
Yes
No
FS-1800/1800N | FS-3800/3800N
6-26
Corrective action
Replace drum unit. See
page 5-12.
Check and straighten pins
of connector (YC702) on
the sensor board (KP-574).
Replace engine board (KP864).
Suggested causes
Corrective action
Suggested causes
Defective paper size switch.
Defective sensor board (KP-574).
Defective engine board (KP-864).
Corrective action
Replace paper size switch.
Replace sensor board (KP574). See page 5-26.
Replace engine board (KP864). See page 5-22.
FS-1800/1800N | FS-3800/3800N
6-27
No message appears
on the message
display (LCD), even
thought the message
background does not
illuminate faintly.
(The power is not
supplied to the LCD
controller board
[KP-738].)
Suggested causes
Corrective action
Defective main board (system DIMM board R e p l a c e m a i n b o a r d
[KP-710*1/KP-689*2]).
(system DIMM [board]).
Defective LCD controller board (KP-738). Replace LCD controller
board (KP-738).
Defective engine board (KP-864).
Replace engine board
(KP-864).
Improper connection of harness (S02402) Reinsert the connector.
between LCD controller board (KP-738)
and engine relay board (KP-760).
Improper connection of harness (S02405) Reinsert the connector.
between engine board (KP-864) and engine
relay board (KP-760).
Defective main board (system DIMM [board R e p l a c e m a i n b o a r d
KP-710*1/KP-689*2]).
(system DIMM [board]).
Defective LCD controller board (KP-738). Replace LCD controller
board (KP-738).
Defective engine board (KP-864).
Replace engine board
(KP-864).
Improper connection of harness (S02402) Reinsert the connector.
between LCD controller board (KP-738)
and engine relay board (KP-760).
Improper connection of harness (S02405) Reinsert the connector.
between engine board (KP-864) and engine
relay board (KP-760).
Broken power cord.
Replace the power cord.
The power cord is not plugged in properly. C h e c k t h e c o n t a c t
between the printers AC
inlet and the outlet.
Measure the AC power
voltage at the outlet.
Replace the power supply
unit. See page 5-22.
FS-1800/1800N | FS-3800/3800N
6-28
: FS-1800/1800N *2 : FS-3800/3800N
Corrective action
Reinsert the connector.
FS-1800/1800N | FS-3800/3800N
6-29
SBSY*
VDFON1
SOIN
VSREQ*
I/O
I
I
I
O
O
O
O
5 V DC
5 V DC
5 V DC
3.3 V/0 V DC
3.3 V/0 V DC
3.3 V/0 V DC (Pulse)
3.3 V/0 V DC
O
O
I
O
0 V/3.3 V DC
0 V/3.3 V DC
3.3 V/0 V DC
0 V/3.3 V DC
B7 SYSRES* O
A8 GND
B8 PDOUT* O
A9
B9
A10
B10
A11
B11
A12
Voltage
0 V/3.3 V DC
0 V/3.3 V DC (Pulse)
GND
GND
GND
VDO+
GND
VDOFPDIR
I
I
O
1.02 to 1.38 V DC
1.38 to 1.02 V DC
3.3 V/0 V DC
B12 GND
A13 +3.3V1
B13 FPCLK
O
O
3.3 V DC
3.3 V/0 V DC (Pulse)
A14 GND
B14 FPDATA I/O
Function
Signal ground
Signal ground
Power supply for main board
Power supply for main board
Power supply for main board
Serial data output signal
Serial line direction signal
Serial clock signal
Engine interrupt request signal
Interrupt/Not Interrupt
Serial line busy signal, Busy/Not busy
Forced video data output signal, On/Off
Serial data input signal
Vertical synchronized request signal
Request/Not request
System reset signal, Reset/Not reset
Signal ground
Pin photo diode sensor [board],
Laser beam detecting signal
Signal ground
Signal ground
Signal ground
LVDS video data signal (positive)
Signal ground
LVDS video data signal (negative)
Communication direction signal with
LCD controller board
Signal ground
Power supply for LCD controller board
Communication data clock signal with
LCD controller board
Signal ground
Communication data signal with LCD
controller board
FS-1800/1800N | FS-3800/3800N
6-30
YC202
I/O
O
O
O
O
O
I
Voltage
5 V/0 V DC
5 V/0 V DC
5 V/0 V DC
0 V/5 V DC
5 V/0 V DC (Pulse)
0 V/5 V DC
20PSDI
OP24V
OP5V
+24V2
FDPFUL*
FUDR
I
O
O
I
I
O
5 V/0 V DC (Pulse)
24 V DC
5 V DC
24 V DC
0 V/5 V DC
0 V/24 V DC
FDDR
0 V/24 V DC
THERM
Analog
EXITPAP* I
0 V/5 V DC
7
8
9
10
11
+5V1
GND
+24V2
SLEEP*
ZCROSS
5 V DC
24 V DC
0 V/5 V DC
5 V/0 V DC (pulse)
Function
Option unit identifying signal 5
Signal ground
Option unit identifying signal 3
Option unit identifying signal 4
Signal ground
Reserved
Serial communication output signal
Option unit ready signal,
Ready, Not ready
Serial communication clock
signal with option unit
Serial communication input signal
Power supply for option unit
Power supply for option unit
Power supply
Paper full sensor, Paper full/Not full
Face up/down solenoid,
Change to face down, On/Off
Face up/down solenoid,
Change to face up, On/Off
Thermistor detecting heat roller
temperature signal
Exit sensor,
Paper Detected/Not detected
Power supply
Signal ground
Power supply
Energy saving mode, On/Off
Zero cross signal
12
HEATON* O
0 V/5 V DC
A19 20PSCLK O
0 V/5 V DC (Pulse)
B19
A20
B20
1
2
3
I
I
O
I
FS-1800/1800N | FS-3800/3800N
6-31
I/O
I
I
I
I
I
I
I
I
O
O
O
I
I
I
O
O
Voltage
5 V DC
5 V DC
5 V DC
5 V DC
24 V DC
24 V DC
24 V DC
24 V DC
24 V DC
24 V DC
24 V DC
24 V DC
24 V DC
24 V DC
0 V/14.7 V DC
0 V/4.3 V DC
11
TNRFUL* O
0 V/4.1 V DC
12
13
+5V2
5 V/0V DC
14
15
16
17
GND
EEDIO
EECLK
I/O
O
5 V/0 V DC (pulse)
5 V/0 V DC (pulse)
REGPAP* I
0 V/5 V DC
18
19
PVOLAN1
TCOVOP
0 V/5 V DC
0 V/5 V DC
I
I
FS-1800/1800N | FS-3800/3800N
6-32
Function
Power supply
Power supply
Power supply
Power supply
Signal ground
Signal ground
Power ground
Power ground
Power supply
Power supply
Power supply
Power supply
Power supply to sensor board
Power supply to sensor board
Power supply to sensor board
Not used
Not used
Power supply
Power supply
Power supply
Eraser lamp [board], Turn On/Off
Waste toner full sensor [board]
(light emitting), Turn On/Off
Waste toner full sensor (light receiving),
Toner full Detected/Not detected
(Signal validates during WTNLED* signal output.)
Reserved
Power supply to sensor board,
Printer status Ready/Sleep
Signal ground
EEPROM (Drum board) data signal
EEPROM (Drum board) clock signal
Registration sensor,
Paper Detected/Not detected
Paper gauge sensor 1, On/Off
Top cover switch, On/Off
YC204
YC205
21
22
1
CSIZE
I
PVOLAN2 I
TRVSEL2* O
Analog
0 V/5 V DC
0 V/24 V DC
TRVSEL1* O
0 V/24 V DC
3
4
+5V1
O
TRVSEL3* O
5 V DC
0 V/24 V DC
5
6
7
TNEMP* I
TRCON* O
TONSCAN O
0 V/5 V DC
0 V/24 V DC
5 V/0 V DC (Pulse)
8
9
10
11
12
13
HVCLK
GND
MCHON*
HUNIT*
RTRCHON*
HANDS*
O
O
I
O
I
5 V/0 V DC (Pulse)
0 V/24 V DC
5 V/0 V DC
0 V/24 V DC
0 V/5 V DC
14
15
16
17
DLPTYPE
+5V2
TMOTDR
CONTYPE
I
O
O
I
18
+24V2
Analog
5 V DC
24 V/0 V DC
5 V DC
(0 V/5 V DC)
24 V DC
Function
Top cover/paper feed unit interlock
switch, On/Off
Paper size switch detecting signal
Paper gauge sensor 2, On/Off
Transfer bias output voltage control
signal 2
Transfer bias output voltage control
signal 1
Power supply for high voltage board
Transfer bias output voltage control
signal 3
Toner sensor, Toner empty/Not empty
Transfer bias, Output On/Off
Toner sensor, Toner detecting clock
signal
Developing bias output clock signal
Power ground
Main charger, Output On/Off
Option feeder, Installed/Not installed
Transfer bias output, Reverse On/Off
MP tray paper sensor,
Paper Detected/Not detected
Developer identifying signal
Power supply for high voltage board
Toner motor, Drive/Stop
Toner container identifying signal
(MICR model only)
Power supply for high voltage board
OP24V
GND
OP5V
OPSCLK
O
O
-
24 V DC
5 V DC
5 V/0 V DC (Pulse)
1
2
3
4
5
Voltage
24 V/0 V DC
FS-1800/1800N | FS-3800/3800N
6-33
YC206
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
I/O
O
I
Voltage
0 V/5 V DC
5 V/0 V DC
Function
Option unit identify signal 0
Serial communication data signal
with option unit
OPSEL1 O
0 V/5 V DC
Option unit identifying signal 1
OPSDO O
5 V/0 V DC
Serial communication data signal
with option unit
OPSEL2 O
0 V/5 V DC
Option unit identifying signal 2
OPRDY* I
0 V/5 V DC
Option unit, Ready/Not ready
GND
Signal ground
+24V2
O
24 V DC
Power supply for engine relay board
+3.3V1
O
3.3 V DC
Power supply for LCD controller board
MPFSOL* O
0 V/24 V DC
MP tray feed solenoid, On/Off
FPDATA I/O 3.3 V/0 V DC
LCD controller board data signal
MIDDR* O
0 V/24 V DC
Middle feed clutch, On/Off
FPDIR
I
3.3 V/0 V DC
LCD controller board
+24V2
O
24 V DC
Power supply for engine relay board
FPCLK
I
3.3 V/0 V DC (Pulse) Communication data clock signal
GND
Power/Signal ground
GND
Power/Signal ground
FEDDR* O
0 V/24 V DC
Feed clutch, On/Off
FPRST* O
3.3 V/0 V DC
LCD controller board reset signal
+24V2
O
24 V DC
Power supply for engine relay board
24 V/15 to 16 V/0 VDC Cooling fan motor,
FANDR O
Speed control High/Low/Stop
REGDR* O
0 V/24 V DC
Registration clutch, On/Off
MMOTON* O
0 V/5 V DC
Main motor, Drive/Stop
GND
Power/Signal ground
MMOTRDY* O
0 V/5 V DC
Main motor, Ready/Not ready
+5V3
O
5 V DC
Power supply for laser scanner unit
SAMPLE1* O
0 V/5 V DC (Pulse)
21
POWCONT O
0 V/5 V DC
22
LASER*
0 V/5 V DC
FS-1800/1800N | FS-3800/3800N
6-34
YC209
I/O
O
O
O
Voltage
1.02 to 1.38 V DC
1.38 to 1.02 V DC
5 V DC
27
28
29
PDIN*
I
GND
POLCLK O
0 V/5 V DC
0 V/5 V DC (Pulse)
30
POLRDY* I
0 V/5 V DC
31
POLON* O
0 V/5 V DC
32
33
34
1
GND
+24V2
O
GND
AIRTEMP I
24 V DC
Analog
2
3
+5V1
O
WETCK1 O
5 V DC
0 V/5 V DC (Pulse)
WETCK2 O
0 V/5 V DC (Pulse)
Function
LVDS video data signal (positive)
LVDS video data signal (negative)
Power/Signal ground
Power supply for laser scanner unit
step-downed from 24 V DC (+24V2)
Pin photo diode sensor detecting signal
Power/Signal ground
Polygon motor rotation speed control
clock signal
Polygon motor start-up ready signal,
Ready/Not ready
Polygon motor drive signal,
Drive/Stop
Power/Signal ground
Power supply for laser scanner unit
Power/Signal ground
Temperature/humidity sensor detecting
external temperature signal
Power supply for engine relay board
Temperature/humidity sensor drive
clock signal 1
Temperature/humidity sensor drive
clock signal 2
FS-1800/1800N | FS-3800/3800N
6-35
Engine board
1
2
33
34
YC209
YC206
Engine board
CN1
1
[Parts side]
[Solder side]
9
18
2
High voltage unit
17
CN2
Engine board
1
2
21
22
18
YC204
YC203
Engine board
Fuser board
1 2 3
YC833
Fuser board
8
YC831
CN2
8
YC902
6-36
(2) All-black
printout
See page 6-39.
(3) Dropouts
See page 6-40.
ABC
123
ABC
123
ABC
123
(7) Unsharpness
(8) Gray
background
See page 6-44.
ABC
123
ABC
123
ABC
123
Square
drawn a
line.
FS-1800/1800N | FS-3800/3800N
6-37
FS-1800/1800N | FS-3800/3800N
6-38
FS-1800/1800N | FS-3800/3800N
6-39
(3) Dropouts
ABC
123
Note the spacing of the defects. Refer to Repetitive defects gauge. See page 6-47.
If the defects occur at regular intervals of 39 mm, the problem may be the damaged developing
roller (in the developer). Replace the developer. See page 3-13.
If the defects occur at regular intervals of 94 mm, the problem may be the damaged drum (in the
drum unit). Replace the drum unit. See page 5-12.
If the defects occur at regular intervals of 72*1/94*2 mm (heat roller) or 79 mm (press roller), the
problem may be the damaged fuser unit. Replace the press roller or heat roller. See page 5-34 or 536. *1: FS-1800/1800N *2: FS-3800/3800N
Check paper property.
Paper with rugged surface or dump tends to cause dropouts. Replace paper with the one that
satisfies the paper specifications.
Check the transfer roller installation.
The transfer roller must be supported by the bushes at the both ends. Clean the bush to remove oil
and debris. Replace the transfer roller if necessary. See page 5-17.
Check the transfer bias potential.
Check the transfer bias output on the high voltage unit. This requires removal of the left cover and
the test equipment. Replace the high voltage unit if high voltage potential is not available on the
board. See page 5-25.
FS-1800/1800N | FS-3800/3800N
6-40
ABC
123
Note the spacing of the defects. Use the Repetitive defects gauge. See page 6-47.
If the defects occur at regular intervals of 94 mm, the problem may be the damaged drum (in the
drum unit). Replace the drum unit. See page 5-12.
If the defects occur at random intervals, the toner may be leaking from the developer and drum
unit. Replace the developer and drum unit. See page 5-4 and 5-12.
(5) Black horizontal streaks
ABC
123
FS-1800/1800N | FS-3800/3800N
6-41
ABC
123
FS-1800/1800N | FS-3800/3800N
6-42
(7) Unsharpness
FS-1800/1800N | FS-3800/3800N
6-43
ABC
123
FS-1800/1800N | FS-3800/3800N
6-44
ABC
123
FS-1800/1800N | FS-3800/3800N
6-45
Square
drawn a
line.
FS-1800/1800N | FS-3800/3800N
6-46
FS-1800/1800N | FS-3800/3800N
6-47
6-48
6-49
Appendix A
Appendix A Contents
Timing charts .......................................................................................................................................... A-4
Cassette feeding, A4 size, face-down tray output ............................................................................... A-4
Cassette feeding, Letter size, face-down tray output .......................................................................... A-5
Cassette feeding, Legal size, face-down tray output .......................................................................... A-6
MP tray feeding, Letter size, face-down tray output ............................................................................ A-7
MP tray feeding, Legal size, face-down tray output ........................................................................... A-8
Wiring diagram ....................................................................................................................................... A-9
Schematic diagrams ............................................................................................................................ A-10
Engine board 1/8 ............................................................................................................................... A-10
Engine board 2/8 ............................................................................................................................... A-11
Engine board 3/8 ............................................................................................................................... A-12
Engine board 4/8 ............................................................................................................................... A-13
Engine board 5/8 ............................................................................................................................... A-14
Engine board 6/8 ............................................................................................................................... A-15
Engine board 7/8 ............................................................................................................................... A-16
Engine board 8/8 ............................................................................................................................... A-17
Main board (TK-777) 1/12 ................................................................................................................. A-18
Main board (TK-777) 2/12 ................................................................................................................. A-19
Main board (TK-777) 3/12 ................................................................................................................. A-20
Main board (TK-777) 4/12 ................................................................................................................. A-21
Main board (TK-777) 5/12 ................................................................................................................. A-22
Main board (TK-777) 6/12 ................................................................................................................. A-23
Main board (TK-777) 7/12 ................................................................................................................. A-24
Main board (TK-777) 8/12 ................................................................................................................. A-25
Main board (TK-777) 9/12 ................................................................................................................. A-26
Main board (TK-777) 10/12 ............................................................................................................... A-27
Main board (TK-777) 11/12 ............................................................................................................... A-28
Main board (TK-777) 12/12 ............................................................................................................... A-29
Main board (TK-858) 1/12 ................................................................................................................. A-30
Main board (TK-858) 2/12 ................................................................................................................. A-31
Main board (TK-858) 3/12 ................................................................................................................. A-32
Main board (TK-858) 4/12 ................................................................................................................. A-33
Main board (TK-858) 5/12 ................................................................................................................. A-34
Main board (TK-858) 6/12 ................................................................................................................. A-35
Main board (TK-858) 7/12 ................................................................................................................. A-36
Main board (TK-858) 8/12 ................................................................................................................. A-37
Main board (TK-858) 9/12 ................................................................................................................. A-38
Main board (TK-858) 10/12 ............................................................................................................... A-39
Main board (TK-858) 11/12 ............................................................................................................... A-40
Main board (TK-858) 12/12 ............................................................................................................... A-41
MMOTON
(Main motor)
POLON
(Polygon motor)
LASER*
(Laser diode)
REGDR
(Registration clutch)
REGPAP
(Registration sensor)
EXITPAP
(Exit sensor)
MIDDR
(Millde feed clutch)
FDON/FUON
Face up/down solenoid
MCHON
(Main charger)
ERASE
(Eraser lamp)
BIAS
(Developing bias)
TRCHON
(Transfer charger)
RTRCHON
(Transfer charger)
FEDDR
(Feed clutch)
100
0 (ms)
FS-1800/1800N | FS-3800/3800N
A-4
1460
1280
1280
1460
1280
330
320
200
300
4450
4450
4450
4400
5230 5600
5590
5790
5800
6810
6880
6860
6730
6810
6880
6170
6420
6650
6880
6660
6630
6830
7660
6960
7020
8030
7850
6610
8850
8230
8250
9750
9170
9290
9290
9020
9070
9020
10
10290
10
11
11
11670
11670
11670
11670
11670
12
12
13 (s)
13 (s)
Timing charts
A-5
330
310
200
300
100
0 (ms)
1550
1380
1380
1550
1380
MMOTON
(Main motor)
POLON
(Polygon motor)
LASER*
(Laser diode)
REGDR
(Registration clutch)
REGPAP
(Registration sensor)
EXITPAP
(Exit sensor)
MIDDR
(Millde feed clutch)
FDON/FUON
Face up/down solenoid
MCHON
(Main charger)
ERASE
(Eraser lamp)
BIAS
(Developing bias)
TRCHON
(Transfer charger)
RTRCHON
(Transfer charger)
FEDDR
(Feed clutch)
4390
5100 5490
5580
5780
5790
6780
6710
6780
6890
6790
6650
6920
6780
6710
6160
6290 6540
6560
6540
6730
7450
7930
7720
8130
8520
8840
8890
8840
8630
8130
8990
9110
9110
4440
4440
4440
10
9570
10060
10
11
11
11490
11490
11490
11490
11490
12
12
13 (s)
13 (s)
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-6
330
320
200
300
100
0 (ms)
1580
1400
1400
1580
1400
MMOTON
(Main motor)
POLON
(Polygon motor)
LASER*
(Laser diode)
REGDR
(Registration clutch)
REGPAP
(Registration sensor)
EXITPAP
(Exit sensor)
MIDDR
(Millde feed clutch)
FDON/FUON
Face up/down solenoid
MCHON
(Main charger)
ERASE
(Eraser lamp)
BIAS
(Developing bias)
TRCHON
(Transfer charger)
RTRCHON
(Transfer charger)
FEDDR
(Feed clutch)
5600
5630
5800
5800
5990
6190
6820
7380
7420
7290
7220
7270
7140
7220
7290
7050
7070
7290
7030
7240
8440
8240
8470
8640
8650
9020
9650
9830
9870
9830
4450
4450
4450
4410
10100
10100
10
10560
9970
10
11
11080
11
12
12
13 (s)
12490
12490
12490
12490
12490
13 (s)
A-7
330
310
200
300
100
0 (ms)
840
1200
1200
1380
1200
MMOTON
(Main motor)
POLON
(Polygon motor)
LASER*
(Laser diode)
REGDR
(Registration clutch)
REGPAP
(Registration sensor)
EXITPAP
(Exit sensor)
MIDDR
(Millde feed clutch)
FDON/FUON
Face up/down solenoid
MCHON
(Main charger)
ERASE
(Eraser lamp)
BIAS
(Developing bias)
TRCHON
(Transfer charger)
RTRCHON
(Transfer charger)
FEDDR
(Feed clutch)
5770
5540
5740
5760
6840
7670
6980
6820
6280
6720
6590
6840
6780
6130
6240 6620
6630
6490
6800
7990
8190
8200 8650
8700
8890
8940
8890
9040
9160
9160
4440
4440
4350
10
9620
10130
10
11
11
11540
11540
11540
11540
11540
12
12
13 (s)
13 (s)
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-8
340
320
200
300
100
0 (ms)
850
1200
1200
1390
1200
MMOTON
(Main motor)
POLON
(Polygon motor)
LASER*
(Laser diode)
REGDR
(Registration clutch)
REGPAP
(Registration sensor)
EXITPAP
(Exit sensor)
MIDDR
(Millde feed clutch)
FDON/FUON
Face up/down solenoid
MCHON
(Main charger)
ERASE
(Eraser lamp)
BIAS
(Developing bias)
TRCHON
(Transfer charger)
RTRCHON
(Transfer charger)
FEDDR
(Feed clutch)
4370
4370
4230
5510
5710
5730
6230
6090
6740
6730
6960
7240
7420
7200
7320
7070
7210
7280
7050
7060
7280
8430
8160
8630
8630
9020
9640
9820
9860
9820
10
10
10550
9970
10090
10090
11
11
11080
12
12
12480
12480
12480
12480
12480
13 (s)
13 (s)
Wiring diagram
Parallel I/F
(RS232C)
Serial I/F
Optional
unit I/F
connctor
1
2
3
4
1
2
3
4
Main motor
S02401
+24V2
1
GND
2
MMOTN*
3
MMOTRDY*
4
Feed clutch
+24V2
1 1
MPFSOL*
2 2
MP Feed
solenoid
+24V2
1 1
MIDDR*
2 2
Middle feed
clutch
(YC807)
FANDR
1 1
GND
2 2
(YC808)
1
2
3
4
5
6
S02402
+3.3V1
FPDATA
FPDIR
FPCLK
GND
FPRST*
6
5
4
3
2
1
S02406
1
2
3
4
5
1
7
2
8
3
9
4
10
5
11
6
12
Optional unit
I/F connector
OP24V
GND
OP5V
(PFSEL)
OPSCLK
OPSEL0
OPSDI
OPSEL1
OPSD0
OPSEL2
OPRDY*
Polygon motor
POLCLK
POLRDY*
POLON*
GND
+24V2
(YC651)
1
2
3
4
5
S02403
+5V3
1 1
1
PD*
2 2
2
GND
3 3
3
1
2
3
4
5
6
Cooling
fan
motor
1
2
3
4
5
6
7
8
9
10
11
12
Network
interface
card*3
(YC07)
(YC802)
(YC205)
1
2
3
4
5
6
7
8
9
10
11
12
KUIO-LV
(YC04)
S02423
S02404
+24V2
OP24V
+5V1
OP5V
(Centronics)
(YC03)
OP24V
(YC06)
1
2
3
4
5
(YC02)
(YC05)
(YS02)
POLCLK
POLRDY*
POLON*
GND
+24V2
12
+24V2
1 1
FDDR*
2 2
APC board
(KP-742)
8 8
9 9
Registration
clutch
(YC602)
1
2
3
4
5
6
7
(YC601)
29
30
31
32
33
34
PDIN*
GND
1
2
3
4
5
6
7
1
2
3
4
1
12
+24V2
1 1
REGDR*
2 2
Temperature
/humidity
sensor
29
30
31
32
33
34
+5V3
SAMPLE*
POWCONT
LASER*
VDD+
VOOGND
(YC801)
19
20
21
22
23
24
25
26
27
28
10
8
6
4
2
12
9
14
17
16
7
18
1
3
11
5
13
15
(YC809)
19
20
21
22
23
24
25
26
27
28
10
8
6
4
2
12
9
14
7
16
17
18
1
3
11
5
13
15
10
8
6
4
2
12
9
14
7
16
17
18
1
3
11
5
13
15
4
3
2
1
+24V2
10
8
6
4
2
12
9
14
7
16
17
18
1
3
11
5
13
15
S02405
GND
FPCLK
PFDIR
FPDATA
+3.3V1
FPRST*
GND
FANDR
+24V2
MMOTON*
GND
MMOTRDY*
+24V2
MPFSOL*
FEDDR*
MIDDR*
+24V2
REGDR*
4
3
2
1
(YS01)
Optional
hard disk
drive slot
S02419
AIRTEMP
+5V1
WETCK1
WETCK2
Option DIMM
Option DIMM
Main board
(KP-777*1/KP858*2)
MICR
switch
MP feed roller
S024**
TMOTDR
3 3
GND
4 4
COM
5 5
6 6
7 7
8 8
CNTYPE
9 9
S02116
MP tray
paper
sensor
7
6
5
4
3
2
1
Option
feeder
sensor
1 1
2 2
S02424 : FS-1800
S02425 : FS-3800
S02426 :
S02427 :
S02428 : FS-1800 MICR
S02429 : FS-3800 MICR
S02430 :
S02431 :
7
6
5
4
3
2
1
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
MicroDrive
*1: FS-1800/1800N
*2: FS-3800/3800N
*3: Standard FS-1800N/
Toner
sensor
TMOTDR
GND
TPMSCAN
1 1
9 9
(GND)
2 2
8 8
S02408
+24V2
CONTYPE
TMOTDR
+5V2
DLPTYPE
HANDS*
RTRCHON*
HUNIT*
MCHON*
GND
HVCLK
TONSCAN
TRCHON*
TNEMP*
TRVSEL3*
+5V1
TRVSEL1*
TRVSEL2*
1
2
3
4
(YC206)
1 1
2 2
TONSCAN
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
(YC204)
Toner
motor
Transfer roller
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
(YC209)
+24V2
Magnet roller
OP24V
OP24V
ERASEDR
9 9
WTNLED*
10 10
TNRFUL*
11 11
12 12
+5V2
13 13
GND
14 14
EEDIO
15 15
EECLK
16 16
REGPAP
17 17
PVPLAM1
18 18
TCPVP
19 19
FCPVP*
20 20
CASIZE
21 21
PVOLAN2
22 22
Grid
Zener board
(KP-768)
(YC01)
(YC201)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
(YC203)
N.C. (GND)
ERASEDR
N.C. (GND)
WTNLED*
EECLK
TNRFUL*
EEDIO
N.C. (+5V2)
GND
+5V2
Top cover
switch
1
2
3
4
5
6
7
8
9
10
(YC701)
(YC742)
(YC741)
1
2
Drum board
(KP-748)
(YC743)
WTNLED*
S02412
ERASEDR
2 2
GND
1 1
(YC761)
Eraser
lamp
[board]
(KP-752)
(YC702)
1
2
3
4
5
6
7
8
9
10
(YC704)
1 1
2 2
(YC771)
Waste
toner full
sensor
[board]
(KP-766)
S02411
+5V2
4
3
2
1
Sensor board
(KP-754)
1
2
3
4
(YC703)
Paper
size switch
S02409
CAS0
COM
CAS1
CAS2
Exit
sensor
+24V2
(YC832)
Waste
toner full
sensor
(receiver)
C S02410
E
S02407
+24V1
1
1
+24V1
2
2
+24V1
3
3
4
4
5
+24V2
5
6
+24V2
6
7
+24V2
7
8
Option
memory
card slot
A20 A20
B20 B20
Engine board
(KP-864)
Fuser board
(KP-756)
(YC833)
FUDR
1 1
+24V2
2 2
FDDR
3 3
1
2
3
4
5
Registration
sensor
Side
cover
interlock
switch
Paper gauge
sensor 1
Paper gauge
sensor 2
(YC834)
+5V2
3 3
FDPFUL
2 2
GND
1 1
1 1
2 2
3 3
+5V1
DBTX
DBRX
DBCLK
GND
1
2
3
4
5
6
7
8
S02413
A1 A1
B1 B1
(YC208)
S02415
FDPFUL*
1
+24V2
2
FUDR
3
FDDR
4
EXITPAP*
5
THERM
6
GND
7
+5V1
8
Face
Paper full
up/down
sensor
solenoid
Thermistor
1 1
1 1
2 2
(YC207)
Controller
unit fan
motor
8
7
6
5
4
3
2
1
Heater lamp
Thermal cutout
2 2
24/23
22/21
20/19
18/17
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
BFANDR(+5V)
GND
(YC831)
+5V1
THERM
24/23
22/21
20/19
18/17
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
(YC202)
SankenR
DL935HA (E)
DL935LA8 (U)
8
7
6
5
4
3
2
1
1 1
3 3
(YC902)
(CN2)
Power
switch
SharpR
A1DU2L1B114(E)
A1DU2L1B113(U)
(CN1)
(YC901)
+24V1/+24V1
+24V1/+24V1
GND/GND
GND/GND
+5V1/+5V1
+5V1/+5V1
ZCROSS/HEATON*
+24V2/SLEEP*
+5V2/GND
THERM/EXITPAP*
FDDR/FUDR
+24V2/FDPFUL*
AC inlet
AC
input
Compact
Flash
S02400
FS-1800/1800N | FS-3800/3800N
A-9
R201
0
TP242
(2) RESET*
(2) SYSCLK
(2) SOOUT
(8) SIOUT
(2) SCLKOUT
(2) GAINT
(3) THERM
(4) PAPVOL
(4) CASIZE
(5) DLPTYPE
(8) AIRTEMP
(5) TONSCAN
(3) ZCROSS
(8) AIRWET
(6) OPTRDY*
(4) EEDIO
(3) HTEMP*
(4) EECLK
(8) VSREQ*
(4) WTONFUL*
(4) WTNLED
(4) ERASE
(4) ERDEAD*
1
2
3
C238
0.1
C201
1000p
TP232
+5V1
PST598D
M/R VCC
SUB
GND VOUT
U203
+5V1
RESET
X0
X1
MOD0
MOD1
MOD2
AVCC
AVR
AVSS
P60/SIN1
P61/SOT1
P62/SCK1
P63/INT7/DTTI
P50/AN0
P51/AN1
P52/AN2
P53/AN3
P54/AN4
P55/AN5
P56/AN6
P57/AN7
P41/PPG0
P42/PPG1
P43/PPG2
P44/PPG3
P45/PPG4
P46/PPG5
P36/SIN0/RDY
P37/SOT0/CLK
P40/SCK0
C207
0.1
R205
10k
C208 0.1
+5V1
MB90560
19
22
23
18
20
21
11
12
13
14
15
16
17
3
4
5
6
7
8
9
10
61
62
63
64
1
2
58
59
60
56
VCC
TP245
WETCK1 (8)
WETCK2 (8)
57
50
51
52
53
54
55
TP241
TP462
TP458
TP243
RA208 100
2
1
4
3
6
5
8
7
TP225
+5V1
Q201
DTC144EUA_01
R206 1k
THDEAD (3)
R203
10k
TP244
RA209
10k
R204
10k
1
A16
A17
A18
A19
RA204 100
RA205 100
1
2
3
4
5
6
7
8
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
A8
A9
A10
A11
A12
A13
A14
A15
RA202 100
RA203 100
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
100
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
TP223
TP205
1
3
5
7
1
3
5
7
TP204
RA201
2
4
6
8
2
4
6
8
TP207
TP203
25
26
27
28
29
30
31
32
RESET* (2)
TP451
C202 0.1
R30/RTO0/ALE
R31/RTO1/RDX
R32/RTO2/WRLX
R33/RTO3/RHX
R34/RTO4/HRQ
R35/RTO5/HAKX
P20/TIN0/A16
P21/TO0/A17
P22/TIN1/A18
P23/TO1/A19
P24/TIN0/A20
P25/TIN1/A21
P26/TIN2/A22
P27/TIN3/A23
P10/INT0/AD08
P11/INT1/AD09
P12/INT2/AD10
P13/INT3/AD11
P14/INT4/AD12
P15/INT5/AD13
P16/INT6/AD14
P17/FRCK/AD15
P00/AD00
P01/AD01
P02/AD02
P03/AD03
P04/AD04
P05/AD05
P06/AD06
P07/AD07
TP202
7
5
3
1
8
6
4
2
+5V1
Q202
2SB1424
ALE (2)
RD* (2)
WR* (2)
PRINT* (8)
TP220
TP222
+5V2
TP208
TP218
30
2
3
29
28
4
25
23
26
27
5
6
7
8
9
10
11
12
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
U202
LA [0: 7]
SST29EE020(PLCC)
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
LA7
LA6
LA5
LA4
LA3
LA2
LA1
LA0
NC
WE*
OE*
CE*
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
1
31
24
22
TP229
TP227
TP228
TP230
R202
10k
+5V1
100
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
A[8:19] (2)
RA206 100
2
1
4
3
6
5
8
7
2
1
4
3
6
5
8
7
TP226
TP217
A[8:19]
RA207
21
20
19
18
17
15
14
13
C206 0.1
+5V1
32
VCC
VSS
U201
VSS
24
VSS
A-10
49
FS-1800/1800N | FS-3800/3800N
16
+5V1
LA [0: 7] (2)
WR* (2)
RD* (2)
FRCS* (2)
AD[0: 7] (2)
Schematic diagrams
TP209
TP210
TP211
TP212
TP213
TP214
TP215
TP216
TP240
TP239
TP238
TP237
TP236
TP235
TP234
TP233
A-11
(1) SYSCLK
TP452
TP444
R213
R211
R209
(8) PDOUT*
(8) 20PTRG
(3) BFANON
(7) POLRDY*
(7) PDIN*
(7) POWCONT
(7) SAMPLE1*
(7) POLCLK
(7) POLON
(7) LASER*
(7) FEDDR
(7) MIDDR
(7) REGDR
(7) MPFSOL
(7) MMOTON
(5) FANON*
(5) FANSPD
(7) FPRST*
(7) MMOTRDY*
(5) RTRCHON
R210
1M
560
X201
16.000MHz
R208
0
27p
C216 27p
C209
TP455
Q203
DTC114EUA_01
(3) SLEEP*
(4) FUON
(4) FDON
(4) REGPAP
(4) TCOVOP
(4) FCOVOP*
(4) SCOVOP*
(3) HEATON
(5) HUNIT*
(5) HANDS*
(5) TNEMP*
(5) TNMOC
(5) CONTYPE
(5) HVCLK1
(5) MCHON
(5) TRCHON
(5) HVCLK2
(5) TRVSEL3
(5) TRVSEL1
(5) TRVSEL2
(5) TMOTON
TP456
R212
TP266
TP265
TP257
TP442
TP443
TP269
TP267
BXIN
SYSCLK
IXIN
TEST
20PTRG
BFANON
RSVIO2
PDOUT*
POLRDY*
PDIN*
POWCONT
SAMPLE1*
POLCLK
POLON
LASER*
FEDDR
MIDDR
REGDR
MPFSOL
MMOTON
FANON*
FANSPD
FPRST*
MMOTRDY*
FGIN
RTRCHON
SLEEP
FUON
FDON
REGPAP
TCOVOP
FCOVOP*
SCOVOP*
HEATON
RSVIO1
SAMPLE2*
VDFON2*
HUNIT*
HANDS*
TNEMP*
TNMOC
CONTYPE
HVCLK1
MCHON
TRCHON
HVCLK2
TRISEL
TRVSEL1
TRVSEL2
TMOTON
TP271
34
2
32
107
104
105
57
48
55
54
53
49
50
52
38
37
36
39
42
44
45
47
40
43
29
30
6
5
7
8
9
10
4
12
35
56
13
14
18
17
19
24
27
26
25
20
22
23
15
16
40
60
76
106
120
33
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
1
11
21
31
41
51
61
71
81
91
101
111
U204
+5V1
RESET*
SYSRES*
SCLKIN
SCLKOUT
SOIN
SOOUT
SDIR
SBSY*
STRIG
VDFON1*
EGIR
FDPFUL*
EXITPAP*
OPSEL0
OPSEL1
OPTSDI
OPSD0
OPSCLK
OPSEL2
OPSEL3
OPSEL4
OPSEL5
GAINT
FRCS*
TEST2
DEVSEL*
DBCLK
DBRX
DBTX
WR*
RD*
ALE
A17
A18
A19
LA0
LA1
LA2
LA3
LA4
LA5
LA6
LA7
78
58
68
59
69
62
67
63
66
64
65
112
113
114
115
108
109
110
116
117
118
119
73
70
72
28
80
79
82
74
75
77
94
93
92
90
89
88
87
86
85
84
83
AD0 103
AD1 102
AD2 100
AD3 99
AD4 98
AD5 97
AD6 96
AD7 65
TP268
TP261
TP262
TP445
TP263
TP258
TP246
TP247
TP248
TP249
TP250
TP251
TP252
TP253
TP254
TP255
A17
A18
A19
TP272
TP270
RESET* (1)
VDFON1* (8)
EGIR (8)
SYSRES* (8)
SCLKIN (8)
SCLKOUT (1)
SOIN (8)
SOOUT (1)
SDIR (8)
SBSY* (8)
FDPFUL* (3)
EXITPAP* (3)
OPSEL0 (6)
OPSEL1 (6)
OPTSDI (6)
OPSD0 (6)
OPSCLK (6)
OPSEL2 (6)
OPSEL3 (6)
OPSEL4 (6)
OPSEL5 (6)
GAINT (1)
FRCS* (1)
WR* (1)
RD* (1)
ALE (1)
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
LA0
LA1
LA2
LA3
LA4
LA5
LA6
LA7
0.1
C210
0.1
C211
RA211 100
RA210 100
1
2
3
4
5
6
7
8
2
1
4
3
6
5
8
7
AD[0: 7]
A[17:19]
0.1
C212
0.1
C213
0.1
C214
+5V1
LA [0: 7]
YC208
0.1
C215
+5V1
CONNECTOR5
LA [0: 7] (1)
AD[0: 7] (1)
A[17:19] (1)
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-12
+5V1
EXITPAP*
THERM
FDDR
(2) BFANON
Power
supply
unit
TP288
FUDR
FDDR
THERM
2 FDPFUL*
6 EXITPAP*
TP284
Q206
DTC114EUA_01
TP287
R226 1k
R225
4.7k
D210
1SS355
YB208
C239
1000p
YB259
Q205
2SB1424
+5V1
+5V1
YB207
YB205
TP446
YB203
YB206
YB204
SLEEP*
10
ZCROSS
11
YB201
R301 0
1
YB202
1
2
+ C301
100/10V
+5V1
HEATON*
+24V2
+24V1 +24V2
12
13
14
15
16
17
18
19
20
21
22
23
24
CONNECTOR24
GND
+24V2
+24V2
SLEEP*
10
ZCROSS
FUDR
11
HEATON*
FDPFUL*
13
12
+5V1
15
14
+5V1
+5V1
17
16
GND
18
GND
+5V1
20
19
GND
GND
22
21
+24V1
23
+24V1
+24V1
24
+24V1
YC202
1
2
C219
TP285
R221
5.6k
TP277
Controller
box fan
motor
CONNECTOR2
YC207
TP381
THERM (1)
FUDR (4)
TP276
SLEEP* (2)
FDDR (4)
C218
R216
10k
C217
R214
10k
+5V1
R228
1.3k
R233
1M
+5V1
R219
3.3k
C221
0.1
R217
2.2k
C223
0.1
R227 1M
2
3 393
+
R220 1M
U205-1
BA1039F_01
1
C222 100p
Q204
DTC114EUA_01
C302
1/50V
C224 0.1
THDEAD (1)
R222
1k
TP278
+5V1
TP283
HEATON (2)
TP282
HTEMP* (1)
FDPFUL* (2)
EXITPAP* (2)
ZCROSS (1)
QA201A
UMD3N_01
QA201B
UMD3N_01 4
TP280
R218
4.7k
+5V1
TP286
R224
4.7k
+5V1
4 U205-2
BA1039F_01
8
6
393
5 +
+5V1
C220 100p
TP275
TP274
TP273
TP454
A-13
(1) WTONFUL*
(1) EDEAD*
(1) ERASE
TP312
(2) FUON
(2) FDON
TP453
2.2k
TP457
Q208
2SD2011
R240
4.7k
R239 1k
TP305
1
2
R252
1k
TP301
DZ201
UDZ2.0B
TP307
R251 30k
ERASEDR
FUDR (3)
FDDR (3)
R249 220
TP314
Q214
2SB1132
TP315
Q213
DTC114YUA_01
+5V1
R250
10k
Q216
2SC4081
Q211
DTA123JUA_01
TP318
+5V1
D206
1SS120
D205
1SS120
TP313
+24V2
D203
1SS120
+24V2
Q208
2SD2011
R242
10k
R244 4.7k
Q215
DTC114EUA_01
TP310
R235
4.7k
R237 2.2k
R230
4.7k
R232
D202
1SS120
+24V2
(1) CASIZE
(1) PAPVOL
R316
10k
+5V1
+5V2
R247 200
R229
DZ204
UDZ3.9B
R245 1k
R241
2.2k
TP311
TP304
DZ202
UDZ3.9B
FCOVOP*
TP300
1YB215 2
1YB213 2
1 YB211 2
TP298 TP296
TNRFUL*
WTNLED*
R238
510
YB217
YB216
YB214
YB218
1YB212 2
+5V2
YB210
1
2
+24V2
YB209
+24V1
C303
100/35V
ERASEDR
TP299
TP297
Q207
2SC4081
QA202 5
UMG9N_01
TP309
TP303 R236
12k
TCOVOP
TP316
R246 1k
REGPAP
+24V2
R231
4.7k
2.2k
R243 22k
C256
1000p
R234
10k
+5V1
TP317
R248
4.7k
TP308
C255
1000p
R233
TP294 TP295 10k
R315
10k
DZ203
UDZ3.9B
(2) FCOVOP*
(2) SCOVOP*
(2) TCOVOP
(2) REGPAP
(1) EECLK
(1) EEDIO
(1) WTNLED
TP289
TP293
YC203
+24V1
PVOLAN2
CSIZE
FCOVOP*
TCOVOP
PVOLAN1
REGPAP
EECLK
EEDIO
GND
+5V2
TNRFUL*
WTNLED*
ERASEDR
+24V2
+24V2
+24V2
GND
GND
+24V1
+24V1
Sensor
board
CONNECTOR22
22
21
20
19
18
17
16
15
14
13
12
11
10
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-14
(2) TMOTON
TP358
(2) HVCLK2
TP353
(2) HVCLK1
(2) RTRCHON
(2) TRVSEL2
(2) TRVSEL1
(2) TRVSEL3
(2) TRCHON
(2) MCHON
TP363
QA206A 1
UMD3N_01
+5V1
QA206B
UMD3N_01
TP342
TP338
TP329
TP325
TP321
TP320
R261
10k
TP354
R258
10k
R259 0
QA205
UMG9N_01
QA204
UMG9N_01
QA203
UMG9N_01
DZ206
UDZ3.9B
R267
10k
TP366
Q220
2SA1576A
1
2
R268
2.2k
R266 1k
TP365
TP370
R263 4.7k
TP361
R262
10k
TP360
Q218
DTC114EUA_01
TP359
TP357
TP347
TP336
TP332
TP327
TP322
TP319
1
2
R265
5.6
Q217
2SB1132
+24V2
TP356
TP355
TP352
TNMOC (2)
TMOTDR
D208
1SS355
(2) HANDS*
(2) HUNIT*
(2) CONTYPE
TMOTDR
(1) DLPTYPE
(1) TONSCAN
(2) TNEMP*
(2) FANSPD
(2) FANON*
R256
10k
TP344
TP367
TP362
YB229
YB227
YB225
YB226
YB224
YB222
1
3
13
11
15
17
16
14
12
10
18
YC204
C304
47/16V
C240
1000p
D207
1SS355
+24V2
HANDS*
HUNIT*
+5V2
CONTYPE
TMOTDR
DLPTYPE
TONSCAN
TNEMP*
GND
+5V1
HVCLK
RTRCHON*
TRVSEL2*
TRVSEL1*
TRVSEL3*
TRCON*
MCHON*
+5V1
FANDR (7)
C305
47/35V
+24V2
High
voltage
unit
CONNECTOR18
13
11
15
17
16
14
12
10
18
Q219
2SD1664
TP369
DZ205
UDZ16B
R317
5.6k
+24V1
TP349
TP350
TP346
TP345
TP341
TP340
TP337
TP335
TP333
TP331
TP330
TP328
TP326
TP324
TP323
YB231
TP334
TP348
1 YB232 2
YB230
YB228
1
2
YB220
1
2
R267
5.6k
HANDS*
HUNIT*
4
QA207
UMG9N_01
CONTYPE
HVCLK
RTRCHON*
TRVSEL1*
YB223
TRVSEL2* 1
2
TRVSEL3* 1YB221 2
TRCHON*
MCHON* 1YB219 2
C228 C229
1000p 1000p
R255
10k
TP364
C227
1000p
R254
10k
+5V1
R257
510
R253
10k
+5V1
(2) OPSCLK
(2) OPSDO
OPSDI
OPRDY*
(2) OPSEL0
(2) OPSEL1
(2) OPSEL2
(2) OPSEL3
(2) OPSEL4
(2) OPSEL5
TP374
TP376
TP379
TP381
TP387
TP390
TP393
TP395
TP397
2
4
6
10
1
15
12
14
12
14
2
4
6
10
1
15
1A1
1A2
1A3
A14
2Y1 11
2Y2 13
1Y1
1Y2
1Y3
1Y4
U206
2A1
2A2
VCC 16
GND 8
3
5
7
9
G1
G2
SN74LS367_01
1A1
1A2
1A3
A14
2Y1 11
2Y2 13
1Y1
1Y2
1Y3
1Y4
U207
2A1
2A2
VCC 16
GND 8
3
5
7
9
G1
G2
SN74LS367_01
+5V1
TP380
TP382
+5V1
C230
0.1
C231
0.1
DZA201
D-ZENER
1
2
3
5
TP396
DZA202
D-ZENER
4
DZA203
D-ZENER
1
2
3
5
20PSCLK (8)
TP378
TP377
100
C306
100/35V
100
+5V1 +24V2
R270
R269
OPTSDI (2)
TP388
TP385
TP391
R274
2.2k
+5V1
R273
2.2k
C233
100p
TP398 TP399
OPTRDY* (1)
100
100
R271
R275
100
100
R276
R272
RA212 100
1
2
3
4
5
6
7
8
C307
100/10V
20PSDO (8)
TP372
TP371
TP375
TP373
TP383
TP384
TP389
TP386
TP394
TP392
OPSDI
OPRDY*
C232
100p
YB234
2
1
YB236
2
1
YB238
2
1
YB235 2
1 YB233 2
YB239
2
1 YB2372
10
12
11
20PSEL3 (8)
20PSEL5 (8)
20PSEL4 (8)
20PRDY* (8)
20PSDI (8)
OP24V (8)
OP24V
OP5V (8)
OP5V
GND
YC205
OPSDI
OPSEL0
OPSCLK
OPSDO
OPSEL1
OPRDY*
OPSEL2
10
12
11
CONNECTOR12
Optional
unit
interface
A-15
1
2
3
5
4
4
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-16
(2) POLON
(2) POLCLK
POLRDY*
(2) PDIN*
(8) VDO-
(8) VDO+
(2) LASER*
TP424
TP427
TP426
TP428
QA208
UMG9N_01
330p
1000p
C242
1000p
C237
R287 56
TP416
TP412
0
C236
TP425
TP408
+5V1
R284
2.2k
R282
R281
QA209B
UMD3N_01
QA209A
UMD3N_01
+5V1
TP406
C308
3.3/50V
U208
BA17805FP
1
3
IN OUT
2 COM
D209 1SS355
TP402
R283
10k
VDO-
VDO+
TP418
TP410
(2) POWCONT
C324
0.1
R277 130 2W
(2) SAMPLE1*
+24V2
CU207
2
CU206
CU205
2
CU204
TP401
2
SAMPLE1*
R280
0
+24V2
R291
0
POLON*
POLRDY*
POLCLK
PDIN*
LASER*
POWCONT
C309
47/35V
CU203
2
CU202
CU201
2
+5V3
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
YC206A
POLRDY*
GND
+24V2
GND
POLON*
(2) REGDR
(2) MIDDR
(2) FEDDR
TP422
TP420
TP417
TP414
(2) MMOTRDY*
(2) MMOTON
(8) FANDR
(2) MPFSOL
APC
board
POLCLK
GND
PDIN*
+5V3
GND
VDO-
VDO+
LASER*
POWCONT
SAMPLE1*
+5V3
CONNECOTR34
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
(8) FPRST*
(8) FPDATA
(8) FPDIR
(8) FPCLK
TP411
TP409
TP423
R290 1k
TP291
R288 1k
R286 1k
TP419
R285 1k
TP415
Q222
2SD1664
R293
4.7k
R292
4.7k
R289
4.7k
Q221
DTC114EUA_01
TP413
R294
4.7k
1
YB244
YB242
YB240
1
2
Q225
2SD1664
+5V1
YB251
YB249
YB247
YB245
1
2
C311
47/16V
REGDR*
MIDDR* 1 YB250 2
FFDDR*
MPFSOL*1YB248 2
+24V2
YB243
1
2
YB241
C310
100/35V
MMOTON*1 YB246 2
FANDR
Q224
2SD1664
Q223
2SD1664
TP405
FPPST*
FPDIR
FPDATA
TP404
TP407
FPCLK
TP403
R279
10k
+5V1 +3.3V1
15
13
11
18
17
16
14
12
10
YC206B
GND
REGDR*
+24V2
MIDDR*
FEDDR*
MPFSOL*
+24V2
MMOTRDY*
GND
MMOTON*
+24V2
FANDR
GND
FPRST*
+3.3V1
FPDATA
FPDIR
FPCLK
Engine
relay
board
CONNECTOR34
15
13
11
18
17
16
14
12
10
A-17
(1) WETCK1
(1) WETCK2
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
YC201
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
1
2
3
4
1
2
3
4
R303 30k
+5V1 +3.3V1
CONNECTOR4PIN
YC209
R311 0
Engine
relay
baord
TP460
TP459
CONNECTOR D40PIN_01
Main baord
GND
PRINT*
+5V1
+5V1
+5V1
SIOUT
SDIR
SCLKN
EGIR
SBSY*
VDFON1
SOIN
VSREQ*
SYSRES*
GND
PDOUT*
GND
GND
GND
VDO+
GND
VDOFPDIR
GND
+3.3V1
FPCLK
GND
FPDATA
20PSEL5
GND
20PSEL3
20PSEL4
GND
20PTRIG*
20PSDO
20PRDY*
20PSCLK
20PSDI
OP24V
OP5V
R306
5.6k
0.1
C244
+5V1
R304
1M
OP5V (6)
OP24V (6)
C243
1000p
AIRTEMP (1)
R305 1k
1 YB2582
1 YB2572
Q226
DTC114EUA_01
358
U209A
C245
TP461
BA10358
+5V1
TP439
0.1
R310
4.7k
R299 0
R307 0
2
3
1
BA10358
358
U209B
R390 4.7k
TP440
TP438
TP437
R298 0
1 YB256 2
TP431
TP435
TP436
R297 1k
TP430
56
R296
1 YB2552
1YB254 2
1YB253 2
YB252
1
2
TP429
56
R295
R300
2.7k
TP463
TP441
AIRWET (1)
20PTRIG (2)
20PSDI (6)
20PSCLK (6)
20PRDY* (6)
20PSDO (6)
20PSEL4 (6)
20PSEL3 (6)
20PSEL5 (6)
FPDATA (7)
FPCLK (7)
FPDIR (7)
VDO- (7)
VDO+ (7)
PDOUT* (2)
SYSRES* (2)
VSREQ* (1)
SOIN (2)
VDFON1* (2)
SBSY* (2)
EGIR (2)
SCLKIN (2)
SDIR (2)
SIOUT (1)
PRINT* (1)
FS-1800/1800N | FS-3800/3800N
220/6.3V
C03
GND
C04
0.1
+3.3V
C05
0.1
C06
0.1
C07
0.1
C08
0.1
TP70
TP71
TP67
TP65
TP68
TP66
TP64
TP69
TP63
TP62
TP61
TP60
TP59
TP55
TP56
TP58
TP54
TP50
TP49
TP46
C09
0.1
CPUA1
CPUA0
CPUA4
CPUA6
CPUA3
CPUA5
CPUA7
CPUA2
CPUA8
CPUA9
CPUA10
CPUA11
CPUA12
CPUA14
CPUA15
CPUA13
CPUA17
CPUA20
CPUA21
CPUA24
CPUA16
CPUA18
CPUA19
CPUA22
TP73
(2) TT1
(2) TBSTN
TP72
(2) TT3
(2) TSIZ2
(2) TSIZ1
(2) ABNN
TP431
TP30
CPUA31
(2) DBBN
(2) TSIZ0
(2) BGN
(2) BCLK
(2) TAN
(2) TEAN
TP443
TP442
TP438
TP439
TP440
TP441
TP436
TP437
TP432
TP433
TP434
TP435
TP470
(2, 4, 9, 10) RSTOUTN
CPUA29
CPUA30
CPUA31
CPUA26
CPUA27
CPUA28
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
VDD2
D5
D4
D3
PVDD33
D2
D1
D0
BUSREQ
RESETN
TEST
BOOTWID1
HOLDREQ
PLLCLK
READY
BUSERR
GND
HOLDACK
WBE3
VDD2
WBE0
WBE1
WBE2
CSN0
CSN2
PVDD33
CSN1
PGND
Blast
CSN3
CNTLIN
PVDD33
VREFIN
OEN
RNW
GND
CPUD22
CPUD21
CPUD20
CPUD25
CPUD24
CPUD23
TP422
CPUA28
CPUA27
CPUA26
CPUA25
CPUA24
TP55
TP53
TP45
TP48
CPUD19
CPUA23
U01
CPUD17
CPUD16
CPUD15
CPUD18
CPUA22
CPUA21
CPUA20
CPUA19
CPUA18
CPUA23
CPUA25
CPUA26
CPUA27
CPUD14
CPUD13
PPC405GF
CPUA17
CPUA16
TP47
TP45
TP44
TP43
CPUA15
CPUA14
CPUA13
CPUA28
CPUD12
CPUD11
CPUD10
CPUD9
CPUD8
CPUA12
TP41
CPUD7
CPUA11
CPUD6
CPUD5
CPUD4
CPUD3
CPUD2
CPUD1
CPUD0
CPUA10
CPUA9
CPUA8
PPC405GF_01
GND
TMRCLK
SYSERR
TRCCYCLE
EVENSTAT1
EVENSTAT0
PVDD33
ODDSTAT1
THMVDD
THMGND
PGND
ODDSTAT0
PVDD33
TRCSTAT3
TRCSTAT2
TRCSTAT1
VDD2
TRCSTAT0
IRQ2
GND
IRQ1
IRQ0
HALTN
TCK
BOOTWID0
TMS
TDI
CLKSTR
TRSTN
TDO
A31
A30
A29
A28
A27
VDD2
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
80
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
GND
+3.3V
CPUA0
CPUA1
CPUA2
CPUA3
CPUA4
TP425
TP426
TP444
+3.3V +3.3V
0
R101
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
GND
D6
D7
D8
PVDD33
D9
D10
D11
PVDD33
D12
PGND
D13
PVDD33
D14
D15
D16
VDD2
D17
D18
GND
D19
D20
D21
D22
D23
PVDD33
D24
PGND
D25
D26
D27
D28
D29
D30
D21
VDD2
VDD2
PLLVDD
A2
A3
A4
A5
A6
A7
PGND
A8
PVDD33
A9
A10
A11
A12
A13
GND
A14
A15
VDD2
A16
A17
A18
PVDD33
A19
PGND
A20
PVDD33
A21
A22
A23
PVDD33
A24
A25
A26
GND
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
A-18
CPUA7
CPUA6
CPUA5
FS-1800/1800N | FS-3800/3800N
RSTOUTN (2,9)
TDO (12)
TMS (12)
TDI (12)
CPUNITN (2)
HALTN (12)
TCK (12)
TP424
0
GND
R103
TP423
A-19
(1) BGN
(1) CPUINTN
(1,4, 9, 10) RSTOUTN
TP155
(1) ABBN
TP450
TP427
(1) DBBN
(1) TT1
(1) TT3
(1) TSIZ0
(1) TSIZ1
(1) TSIZ2
(1) TAN
(1) TEAN
(1) TBSTN
+3.3V
(1) CPUA31
CPUD0
CPUD1
CPUD2
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
CPUD8
CPUD9
CPUD10
CPUD11
CPUD12
CPUD13
CPU D14
CPUD15
CPUD16
CPUD17
CPUD18
CPUD19
CPUD20
CPUD21
CPUD22
CPUD23
CPUD24
CPUD25
CPUD26
CPUD27
CPUD28
CPUD29
CPUD30
CPUD31
AF21
AE20
AD14
AC15
AE16
AE15
AC17
AD18
AF15
AD17
AE17
AF17
AD16
AE18
AF18
AF16
AA24
AA25
AA26
AB23
AB24
AB25
AB26
AC24
AC25
AC26
AD24
AD25
AD26
AE25
AE25
AF25
AE14
AF14
AD13
AE13
AF13
AC12
AD12
AE12
AF12
AD11
AE11
AF11
AC10
AD10
AF10
AD9
CPUINT
RSTOUTX
BGN
BRN
ABBN
AACKN
DBGN
DBBN
TT1
TT3
TSIZ0
TSIZ1
TSIZ2
TAN
TEAN
TBST
CPUD0
CPUD1
CPUD2
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
CPUD8
CPUD9
CPUD10
CPUD11
CPUD12
CPUD13
CPUD14
CPUD15
CPUD16
CPUD17
CPUD18
CPUD19
CPUD20
CPUD21
CPUD22
CPUD23
CPUD24
CPUD25
CPUD26
CPUD27
CPUD28
CPUD29
CPUD30
CPUD31
U02-1
ASIC
Block1/2
ASDA0
ASDA1
ASDA2
ASDA3
ASDA4
ASDA5
ASDA6
ASDA7
ASDA8
ASDA9
ASDA10
ASDA11
ASDA12
ASDBA0
ASDBA1
ASDCSN0
ASDCSN1
ASDCSN2
ASDCSN3
ASDCSN4
ASDCSN5
C25
E25
C24
F24
B26
E23
B25
D26
A25
D25
A24
C26
A21
D24
C22
C21
A20
A19
B19
A18
B18
MB87J4300
BIU603
SIDIR
SIOEN
ALATCH
EXTBDIR
EXTBOEN
SDD0
SDD0
SDD1
SDD1
SDD2
SDD2
SDD3
SDD3
SDD4
SDD4
SDD5
SDD5
SDD6
SDD6
SDD7
SDD7
SDD8
SDD8
SDD9
SDD9
SDD10
SDD10
SDD11
SDD11
SDD12
SDD12
SDD13
SDD13
SDD14
SDD14
SDD15
SDD15
SDD16
SDD16
SDD17
SDD17
SDD18
SDD18
SDD19
SDD19
SDD20
SDD20
SDD21
SDD21
SDD22
SDD22
SDD23
SDD23
SDD24
SDD24
SDD25
SDD25
SDD26
SDD26
SDD27
SDD27
SDD28
SDD28
SDD29
SDD29
SDD30
SDD30
SDD31
SDD31
ASDD0
ASDD1
ASDD2
ASDD3
ASDD4
ASDD5
ASDD6
ASDD7
ASDD8
ASDD9
ASDD10
ASDD11
ASDD12
ASDD13
ASDD14
ASDD15
ASDD16
ASDD17
ASDD18
ASDD19
ASDD20
ASDD21
ASDD22
ASDD23
ASDD24
ASDD25
ASDD26
ASDD27
ASDD28
ASDD29
ASDD30
ASDD31
D10
AC20
AD15
AC3
AD19
AE19
A12
A13
B13
C13
A14
B14
A15
B15
D15
A16
B16
C16
A17
B17
C17
D17
J25
J26
K23
K24
K25
K26
L25
L26
F25
F26
G23
G25
G26
H24
H25
H26
C15 ADDQMLL
DQM0
C18 ADDQMLM
DQM1
J24 ADDQMUM
DQM2
E26 ADDQMUU
DQM3
B12
IICSDA
A11
IICSCL
D20 ASDCKE
CKE
B20
SDCLKIN
B21
SDCLKOUT
B23 ASDCASN
SDCASN
D22 ASDRASN
SDRASN
C19 ASDWEN
SDWEN
SDCSN0
SDCSN1
SDCSN2
SDCSN3
SDCSN4
SDCSN5
SDA0
SDA1
SDA2
SDA3
SDA4
SDA5
SDA6
SDA7
SDA8
SDA9
SDA10
SDA11
SDA12
SDBA0
SDBA1
TP127
EXTBDIR (4)
EXTBOEN (4, 8)
GND
TP153
TP154
TP158
TP131
C42
CHIP EL.
220/6.3V
SDCLKOUT
TP136
TP123
TP145
TP119
TP156
TP157
TP137
TP141
TP146
TP147
TP148
GND
C43
0.1
GND
C49
0.1
+3.3V
+2.5V
SDA8
SDA9
SDA10
SDA11
RA19 0x4
7
8
5
6
3
4
1
2
RA21 0x4
1
2
3
4
5
6
7
8
C50
0.1
C44
0.1
C51
0.1
C45
0.1
C52
0.1
C46
0.1
ACB1608H-060
RA23 0x4
7
8
5
6
3
4
1
2
R11
RA22 0x4
1
2
3
4
5
6
7
8
SDA4
SDA5
SDA6
SDA7
RA18 0x4
7
8
5
6
3
4
1
2
C53
0.1
C47
0.1
C54
0.1
C48
0.1
DQMLL (6, 7)
DQMLM (6, 7)
DQMUM (6, 7)
DQMUU (6, 7)
SDCLK (6, 7)
SDCASN (6, 7)
SDRASN (6, 7)
SDWEN (6, 7)
SDCKE (6, 7)
SDCSN2
SDCSN3
SDCSN4
SDCSN5
RA20 0x4
SDA12
7
8
SDBA0
5
6
SDBA1
3
4
1
2 SDCSN0
SDA0
SDA1
SDA2
SDA3
0x4
8
6
4
2
RA17
7
5
3
1
C140
0.1
1k
R09
1k
+3.3V
C28
GND
C29
100p 100p
R08
SDCSN2 (7)
SDCSN3 (7)
SDCSN4 (7)
SDCSN5 (7)
SDBA0 (6, 7)
SDBA1 (6, 7)
SDCSN0 (6)
TP135
IICSDA (7)
IICSDL (7)
GND
A1
A26
D6
D11
D16
D21
F4
F23
L4
L23
T4
T23
AA4
AA23
AC6
AC11
AC16
AC21
AF1
AF26
A23
C5
C14
C20
C23
G24
M3
R24
MB87J4300
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
OVSS
OVSS
OVSS
OVSS
OVSS
OVSS
OVSS
OVSS
U02-5
M4 AGND
N3 AGND
P2 AGND
R26 AGND
+2.5V
MB87J4300
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
OVDDE5
OVDDE5
OVDDE5
OVDDE5
VDDE5
OVDDE5
OVDDE5
D4
D9
D13
D18
D23
J4
J23
N23
P4
V4
V23
AC4
AC9
AC14
AC18
AC23
MB87J4300
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
U02-4
N1
AVDD
N2
AVDD
P3
AVDD
U26
AVDD
D14
D19
H4
H23
N4
P23
W4
W23
AC8
AC13
AC19
U02-3
A22
B22
B24
D5
D8
F24
Y23
+3.3V
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-20
(12) OPRDY2
(10) OPRSTN2
TP183
TP182
TP191
(12) FPDAT
(12) FPCLK
(12) FPDIR
(8) CFRST1
(8) CFRST2
(8) CFCSN1
(8) CFCSN2
(8) CFOEN1
(8) CFOEN2
(8) CFWEN1
(8) CFWEN2
(8) CFWAITAN1
(8) CFWAITBN2
(8) CDET1A
(8) CDET1B
(8) CDET2A
(8) CDET2B
(5) OPRST1
(5) OPRDY1
(5) DMAACKN1
TP178
TP180
(5) DMAREQ1
(5) IORN1
TP172
TP174
(5) IOWN1
TP175
TP176
(5) OP1RN1
(5) KUIOCSN1
TP169
TP170
(5) IODATACKN1
(11) XTXD
(11) XRXD
(11) XRTS
(11) XCTS
(11) XDSR
(11) XDTR
(11) RSSEL
(10) ACK
(10) BUSY
(10) PERROR
(10) SELECT
(10) FAULT
(10) STROBE
(10) WAUTOFD
(10) INIT
(10) SELECTION
(10) P1284DIR
(10) P1284HD
PDATA1
PDATA2
PDATA3
PDATA4
PDATA5
PDATA6
PDATA7
PDATA8
GND
G4
A5
C6
B6
A6
A7
J2
J3
G1
G3
H1
H2
H3
J1
K1
K2
F1
K3
G2
K4
M25
M24
M24
T25
U25
V25
N26
P26
P24
R25
T24
R23
W26
W25
Y24
M26
N25
N24
U24
V24
U23
V26
W24
Y26
Y25
R1
P1
T2
R4
R2
R3
T3
Y1
W3
W2
W1
V3
V2
V1
U4
AA2
AA1
Y4
Y3
Y2
U1
U2
T1
U3
AB1
AA3
PCTEST
TSTMODE
FPRST
FPDAT
FPCLK
FPDIR
RSTA
RSTB
CFCSN1
CFCSN2
CFOEN1
CFOEN2
CFWEN1
CFWEN2
WAITAN
WAITBN
CDET1A
CDET1B
CDET2A
CDET2B
KUIOCSN1
KUIOCSN2
KUIOCSN3
IODATACKN1
IODATACKN2
IODATACKN3
IORN1
IORN2
IORN3
IOWN1
IOWN2
IOWN3
OP1RN1
OP1RN2
OP1RN3
DMAACK1
DMAACK2
DMAACK3
DMAREQ1
DMAREQ2
DMAREQ3
OPRDY1
OPRDY2
OPRST1
OPRST2
TXD
RXD
RTS
CTS
DSR
DTR
RSSEL
PAD0
PAD1
PAD2
PAD3
PAD4
PAD5
PAD6
PAD7
ACK
BUSY
PERROR
SELECT
FAULT
STROBE
AUTOFD
INIT
SELECTION
P1284DIR
P1284HD
U02-2
Waverly
(352BGA)
block2/2
ASIC
Block 2/2
C10
C9
B10
A10
C12
B7
A8
B5
A4
B2
B3
B4
C3
A2
C2
C4
A3
B1
D2
E1
C1
D1
D3
E2
E3
E4
F2
F3
M1
L2
M2
B11
C11
D12
L1
L3
T26
P25
D7
A9
L24
AF20
AF19
AB2
AB3
AB4
B8
C8
C7
B9
AF24
AF24
AD23
AF23
AD20
AF21
AD21
AF22
AF22
AD22
AF23
AC22
MB87J4300
ENGIRN
SBSY
SDIR
SCLK
SI
SO
RSTINX
VDFONSPL0
VDFONSPL1
VDATA0
VDATAN0
VDATAP0
VDATAN1
VDATAP1
BD
BIASP
BIASN
SVCCLK
AUXIN
AUXCLK
AUXOUT0
AUXOUT1
AUXOUT2
AUXOUT3
AUXOUT4
AUXOUT5
AUXOUT6
AUXOUT7
XTST
XSM
MST
SMCK
EXTIOR1
EXTIOR2
VXIN
VXOUT
CXIN
CXOUT
CXX2
PLGCLK
OPBCLK
BCLKIN
BCLKOUT
DBCLK
DBTXD
DBRXD
VBUS
USBDP
USBDN
CLK48IN
ROMA1
ROMA2
ROMA3
ROMA4
ROMCSN0
ROMCSN1
ROMCSN2
ROMCSN3
ROMOEN0
ROMOEN1
ROMWEN0
ROMWEN1
VDATAN
VDATAP
ROMA1
ROMA2
ROMA3
ROMA4
CSN0
CSN1
CSN2
CSN3
OEN0
OEN1
WEN0
WEN1
TP173
TP376
TP171
TP168
TP167
27
ENGIRN (12)
SBSY (12)
SDIR (12)
SCLK (12)
SI (12)
SO (12)
RSTIN (12)
TP187
TP188
BD (9, 12)
VDFON (12)
FSYNC (9)
TP186
XLIDATA (9)
SRCCLKN (9)
PVIDEO0 (9)
PVIDEO1 (9)
PVIDEO2 (9)
PVIDEO3 (9)
PVIDEO4 (9)
PVIDEO5 (9)
PVIDEO6 (9)
PVIDEO7 (9)
R19
SELECTIN (10)
EXTIOR2 (12)
TP374
+3.3V
R14
TP165
TP166
DBCLK (12)
DBTXD (12)
DBRXD (12)
TP159
ROMA1 (5)
ROMA2 (4)
ROMA3 (4)
ROMA4 (4)
CSN0 (4)
CSN1 (4)
CSN2 (5, 9)
CSN3 (5)
CSN0 (4, 9)
CSN1 (5)
WEN0 (4, 5, 9)
TP164
TP181
TP192
TP189
TP179
TP160
TP161
TP162
TP163
0.1
0.1
R112
R113
GND
C61
TP184
R21
430F
GND
C60
R20
R16
+3.3V
EXTIORC (10)
SVCCLK (9)
BCLK (1)
6
4
2
8
TP193
TP190
100F
R210
3.3 k
R15
10kx4
TP372
5
3
1
7
RA24
R22
TP185
GND
240F
330
25.0000 MHz
X01
TP375
GND
ACT3225-102_01
CHOKE-COIL
L03
R17
330
+3.3V
0
R13
(10) PDATA [ 8: 1]
+3.3V
C56
C55
C58
TP377
22p
22p
VDOUTP (12)
VDOUTN (12)
25.50629 MHz
C59
X02
18p
18p
GND
GND
CPUA6
CPUA5
CPUA4
CPUA3
CPUA2
CPUA14
CPUA13
CPUA12
CPUA11
CPUA10
CPUA9
CPUA8
CPUA7
CPUA22
CPUA21
CPUA20
CPUA19
CPUA18
CPUA17
CPUA16
CPUA15
A-21
GND
GND
GND
19
1
2
3
4
5
6
7
8
9
19
1
2
3
4
5
6
7
8
9
19
1
2
3
4
5
6
7
8
9
VCC
GND
B1
B2
B3
B4
B5
B6
B7
B8
20
10
18
17
16
15
14
13
12
11
VCC
GND
B1
B2
B3
B4
B5
B6
B7
B8
20
10
18
17
16
15
14
13
12
11
18
17
16
15
14
13
12
11
20
VCC
10
GND
B1
B2
B3
B4
B5
B6
B7
B8
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U05
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U04
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U03
C65
0.1
+3.3V
C64
0.1
LA6
LA5
LA4
LA3
LA2
TP200
TP201
TP202
(3, 5, 9) WEN0
(3, 9) OEN0
(3) CSN0
(3) CSN1
TP206
TP205
TP204
TP203
TP199
TP198
TP197
TP196
TP194
+3.3V
(3) ROMA2
(3) ROMA3
(3) ROMA4
TP195
LA14
LA13
LA12
LA11
LA10
LA9
LA8
LA7
LA22
LA21
LA20
LA19
LA18
LA17
LA16
LA15
C63
0.1
+3.3V
C62
LA5
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
CPUD0
CPUD1
CPUD2
LA19
LA20
LA21
LA22
LA15
LA16
LA17
LA18
CPUD24
CPUD25
CPUD26
CPUD27
CPUD28
CPUD29
CPUD30
CPUD31
CPUD20
CPUD21
CPUD22
CPUD23
LA13
LA14
CPUD16
CPUD17
CPUD18
CPUD19
LA10
LA11
LA12
CPUD8
CPUD9
CPUD10
CPUD11
CPUD12
CPUD13
CPUD14
CPUD15
LA6
LA7
LA8
LA9
GND
22/6.3V
CHIP EL.
GND
+3.3V
System
(ROM)
DIMM
YS01
CONNECTOR 72PIN
1 GND
2 DQ0
3 DQ1
4 DQ2
5 VCC
6 DQ3
7 DQ4
8 DQ5
9 DQ6
10 DQ7
11 GND
12 A2
13 A3
14 A4
15 A5
16 NC
17 A6
(2, 8) EXTBOEN
18 A7
(2) EXTBDIR
19 A8
20 A9
21 GND
22 DQ8
23 DQ9
24 DQ10
25 DQ11
26 DQ12
27 DQ13
28 DQ14
29 DQ15
30 VCC
31 A10
32 A11
33 A12
34 NC
35 DQ16
36 DQ17
37 DQ18
38 DQ19
39 GND
40 OEN
41 CE1N
42 CE2N
43 A13
44 A14
45 NC
46 NC
47 WEN
48 VCC
49 DQ20
50 DQ21
51 DQ22
52 DQ23
53 GND
54 DQ24
55 DQ25
56 DQ26
57 DQ27
58 DQ28
59 DQ29
60 DQ30
61 DQ31
62 VCC
63 A15
64 A16
65 A17
66 A18
67 NC
68 A19
69 A20
70 A21
71 A22
72 GND
CPUD7
CPUD6
CPUD5
CPUD4
CPUD3
CPUD2
CPUD1
CPUD0
CPUD15
CPUD14
CPUD13
CPUD12
CPUD11
CPUD10
CPUD9
CPUD8
19
1
2
3
4
5
6
7
8
9
19
1
2
3
4
5
6
7
8
9
GND
VCC
GND
B1
B2
B3
B4
B5
B6
B7
B8
20
10
18
17
16
15
14
13
12
11
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U07
GND
0.1
C67
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
+3.3V
0.1
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
C66
18
17
16
15
14
13
12
11
20
10
VCC
GND
B1
B2
B3
B4
B5
B6
B7
B8
+3.3V
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U06
LD [15: 0]
LD [15: 0] (5, 8)
LA [22: 2] (5, 8, 9)
FS-1800/1800N | FS-3800/3800N
(4, 8) LA20
R110
(3) ROMA1
(4, 8) LD [15: 0]
(4, 8, 9) LA [22: 2]
ALA20
LA19
LA18
LA17
LA16
LA15
LA14
LA13
LA12
LA11
LA10
LA9
LA8
LA7
LA6
LA5
LA4
LA3
LA2
TP207
LA21
LA20
LA19
LA18
LA17
LA16
LA15
LA14
LA13
LA12
LA11
LA10
LA9
LA8
LA7
LA6
LA5
LA4
LA3
LA2
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
FS-1800/1800N | FS-3800/3800N
A-22
13
32
12
14
33
31
29
27
A5
22
20
18
16
30
28
26
24
21
19
17
15
GND
GND
/CE
/OE
/BYTE
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
12
31
11
13
32
30
28
26
24
21
19
17
15
29
27
25
23
20
18
16
14
VCC
U09S
42
1 A19
2 A18
33 A17
34 A16
35 A15
36 A14
37 A13
38 A12
39 A11
40 A10
41 A9
3 A8
4 A7
5 A6
6 A5
7 A4
8 A3
9 A2
10 A1
A0
22
GND
GND
/CE
/OE
/BYTE
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MX23L1610MC10KF2
1
NU
23
VCC
44
43
2
3
34
35
36
37
38
39
40
41
42
4
5
6
7
8
9
10
11
U08
GND
C69
CSN3
OEN1
+3.3V
0.1
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
GND
C68
0.1
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
+3.3V
CSN3 (3)
OEN1 (3)
CSN2 (3, 9)
OEN1 (3)
C72
+5V
1
3
5
7
BA033FP
C70
22/6.3V
5V - 3.3V REGULATOR
U24
3
1
2 IN OUT
COM
D01 1SS355
2
1
(3) DMAACKN1
(3) IORN1
(3) IOWN1
(3) OPRSTN1
(3) OPRDY1
(3) DMAREQ1
(3) KUIOCSN1
(3) IODTACKN1
(3) OPIRN1
+3.3V
GND
2
4
6
8
GND
C71
0.1
+KUIO3.3V
2.2kx4
RA25
LA16
LA8
LA7
LA6
LA5
LA4
LA3
LA2
LA15
LA14
LA13
LA12
LA11
LA10
LA9
+5V
GND
+KUIO3.3V
G1
G2
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A21
B21
A22
B22
A23
B23
A24
B24
A25
B25
A26
B26
A27
B27
A28
B28
A29
B29
A30
B30
CONNECTOR KUIO
LockPin(A1)
LockPin(A30)
NC
NC
NC
NC
GND
Power 3.3V
Power 3.3V
A15
GND
A14
A13
A12
A11
A10
A9
A8
GND
A7
A6
A5
A4
A3
A2
A1
GND
Power 3.3V
/OP2IF
/OP2ACK
/OP2IR
Power 5V
RDY
DREQ
GND
/DMACK
/IOR
/IOW
/RESET
VOLT DETECT
D15
D14
GND
D13
D12
D11
D10
D9
D8
D7
GND
D6
D5
D4
D3
D2
D1
D0
GND
NC
NC
NC
YC04
KUIO-LV
A-23
ASDD22
ASDD30
ASDD23
ASDD31
ASDD20
ASDD28
ASDD21
ASDD29
ASDD18
ASDD26
ASDD19
ASDD27
ASDD16
ASDD24
ASDD17
ASDD25
ASDD6
ASDD14
ASDD7
ASDD15
ASDD4
ASDD12
ASDD5
ASDD13
ASDD2
ASDD10
ASDD3
ASDD11
ASDD0
ASDD8
ASDD1
ASDD9
TP240
TP236
TP232
TP224
TP220
TP216
TP212
TP208
RA33 56x4
2
1
4
3
6
5
8
7
RA32 56x4
2
1
4
3
6
5
8
7
RA31 56x4
2
1
4
3
6
5
8
7
RA30 56x4
2
1
4
3
6
5
8
7
RA29 56x4
2
1
4
3
6
5
8
7
RA28 56x4
2
1
4
3
6
5
8
7
RA27 56x4
2
1
4
3
6
5
8
7
RA26 56x4
2
1
4
3
6
5
8
7
SDD22
SDD30
SDD23
SDD31
SDD20
SDD28
SDD21
SDD29
SDD18
SDD26
SDD19
SDD27
SDD16
SDD24
SDD17
SDD25
SDD6
SDD14
SDD7
SDD15
SDD4
SDD12
SDD5
SDD13
SDD2
SDD10
SDD3
SDD11
SDD0
SDD8
SDD1
SDD9
SDD [31: 0]
+3.3V
SDD31
SDD30
SDD29
SDD28
SDD27
SDD26
SDD25
SDD24
SDD23
SDD22
SDD21
SDD20
SDD19
SDD18
SDD17
SDD16
SDD15
SDD14
SDD13
SDD12
SDD11
SDD10
SDD9
SDD8
SDD7
SDD6
SDD5
SDD4
SDD3
SDD2
SDD1
SDD0
C73
0.1
1
15
29
43
3
9
35
41
49
55
75
81
2
4
5
7
8
10
11
13
74
76
77
79
80
82
83
85
31
33
34
36
37
39
40
42
45
47
48
50
51
53
54
56
VSS
VSS
VSS
VSS
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
NC
NC
NC
NC
NC
NC
NC
/CS
/RAS
/CAS
/WE
CLK
CKE
DQM0
DQM1
DQM2
DQM3
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11(BA1)
A12(BA0)
SDRAM 64M
C74
0.1
TC59S6432CFT-80
VCC
VCC
VCC
VCC
VCCQ
VCCQ
VCCQ
VCCQ
VCCQ
VCCQ
VCCQ
VCCQ
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
U10
44
58
72
86
6
12
32
38
46
52
78
84
14
21
30
57
69
70
73
20
19
18
17
68
67
16
71
28
59
25
26
27
60
61
62
63
64
65
66
24
23
22
SDBA1 (2, 7)
SDBA0 (2, 7)
TP428
SDCSN0 (2)
SDRASN (2, 7)
SDCASN (2, 7)
SDWEN (2, 7)
SDCKE (2, 7)
DQMUU (2, 7)
DQMUM (2, 7)
DQMLM (2, 7)
DQMLL (2, 7)
GND
SDA0
SDA1
SDA2
SDA3
SDA4
SDA5
SDA6
SDA7
SDA8
SDA9
SDA10
SDA11
GND
R25
100
R24
100
+3.3V
SDCLK (2, 7)
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-24
SDA11
SDA1
SDA3
SDA5
SDA7
SDA9
SDA12
SDA0
SDA2
SDA4
SDA6
SDA8
SDA10
GND
(2, 6) DQMLL
(2) SDCSN3
(2, 6) SDCKE
(2, 6) SDCLK
(2, 6) SDRASN
(2, 6) SDCASN
(2, 6) SDBA0
(2, 6) DQMUM
(2) IICSDA
(2) IICSCL
(2, 6) DQMLM
(2, 6) SDCKE
(2, 6) SDWEN
(2) SDCSN2
(2, 6) SDCLK
(2, 6) SDBA1
(2, 6) DQMUU
SDD3
SDD2
SDD1
ADD0
SDD7
SDD6
SDD5
ADD4
SDD19
SDD18
SDD17
ADD16
SDD23
SDD22
SDD21
ADD20
SDD11
SDD10
SDD9
ADD8
SDD15
SDD14
SDD13
ADD12
SDD27
SDD26
SDD25
SDD24
SDD31
SDD30
SDD29
SDD28
C76
47/6.3V
+3.3V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
GND
DQ0
DQ1
DQ2
DQ3
VCC
DQ4
DQ5
DQ6
DQ7
/DQMB0
GND
A0
A2
A4
A6
A8
A10/AP
BA1
A12
VCC
DU
RFU
RFU
CK0
GND
CKE0
/WE
/S0
/S2
VCC
NC
NC
NC
NC
GND
/DQMB2
DQ16
DQ17
DQ18
DQ19
VCC
DQ20
DQ21
DQ22
DQ23
GND
SDA
SCL
VCC
GND
DQ8
DQ9
DQ10
DQ11
VCC
DQ12
DQ13
DQ14
DQ15
/DQMB1
GND
A1
A3
A5
A7
A9
BA0
A11
A13
VCC
/RAS
/CAS
RFU
CK1
GND
CKE1
NC
S1
S3
VCC
NC
NC
NC
NC
GND
/DQMB3
DQ24
DQ25
DQ26
DQ27
VCC
DQ28
DQ29
DQ30
DQ31
GND
SA0
SA1
SA2
YS02
Optional
expanding
memory
(DIMM)
slot 1
SDA11
SDA1
SDA3
SDA5
SDA7
SDA9
SDA12
SDA0
SDA2
SDA4
SDA6
SDA8
SDA10
SDD3
SDD2
SDD1
ADD0
SDD7
SDD6
SDD5
ADD4
SDD19
SDD18
SDD17
ADD16
SDD23
SDD22
SDD21
ADD20
SDD11
SDD10
SDD9
ADD8
SDD15
SDD14
SDD13
ADD12
SDD27
SDD26
SDD25
SDD24
SDD31
SDD30
SDD29
SDD28
GND
(2, 6) DQMLL
(2) SDCSN5
(2, 6) SDCKE
(2, 6) SDCLK
(2, 6) SDRASN
(2, 6) SDCASN
(2, 6) SDBA0
(2, 6) DQMUM
(2) IICSDA
(2) IICSCL
(2, 6) DQMLM
(2, 6) SDCKE
(2, 6) SDWEN
(2) SDCSN4
(2, 6) SDCLK
(2, 6) SDBA1
(2, 6) DQMUU
+3.3V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
GND
DQ0
DQ1
DQ2
DQ3
VCC
DQ4
DQ5
DQ6
DQ7
/DQMB0
GND
A0
A2
A4
A6
A8
A10/AP
BA1
A12
VCC
DU
RFU
RFU
CK0
GND
CKE0
/WE
/S0
/S2
VCC
NC
NC
NC
NC
GND
/DQMB2
DQ16
DQ17
DQ18
DQ19
VCC
DQ20
DQ21
DQ22
DQ23
GND
SDA
SCL
VCC
GND
DQ8
DQ9
DQ10
DQ11
VCC
DQ12
DQ13
DQ14
DQ15
/DQMB1
GND
A1
A3
A5
A7
A9
BA0
A11
A13
VCC
/RAS
/CAS
RFU
CK1
GND
CKE1
NC
S1
S3
VCC
NC
NC
NC
NC
GND
/DQMB3
DQ24
DQ25
DQ26
DQ27
VCC
DQ28
DQ29
DQ30
DQ31
GND
SA0
SA1
SA2
YS03
Optional
expanding
memory
(DIMM)
slot 2
A-25
(3) CDET2B
(3) CDET2A
(3) CFWAITN2
+3.3V
(3) CFCSN1
(3) CFOEN2
RA35
10kx4
TP388
TP386
TP415
(3) CFRST2
(3) CFWEN2
TP413
(3) CFCSN2
TP403
TP245
TP253
LD8 TP255
LD9
LD10
LA20TP251
TP249
TP247
LD11
LD12
LD13
LD14
LD15
LD0
LD1
LD2
LA7
LA6
LA5
LA4
LA3
LA2
LA10
LA9
LA8
LA11
LD3
LD4
LD5
LD6
LD7
+3.3V
51
52
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
(2, 4) EXTBOEN
(3) CFOEN1
(3) CFCSN1
(3) CFCSN2
CONNECTOR CF-CARD
GND
D3
D4
D5
D6
D7
/CE1
A10
/OE
A9
A8
A7
VCC
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
WP
/CD2
/CD1
D11
D12
D13
D14
D15
/CE2
/VS1
/IORD
/IOWR
/WE
RDY//BSY
VCC
/CSEL
/VS2
RESET
/WAIT
/INPACK
/REG
BVD2
BVD1
D8
D9
D10
GND
YC06
C80
22/6.3V
(4, 5, 9) LA [22: 0]
2
4
6
8
LA4
LA3
LA2
LA20
LA11
LA10
LA9
LA8
LA7
LA6
LA5
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
1
15
2
4
6
10
12
14
19
1
2
3
4
5
6
7
8
9
GND
VCC
GND
D1
D2
D3
D4
D5
D6
D7
D8
20
10
18
17
16
15
14
13
12
11
VCC
GND
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
16
8
3
5
7
9
11
13
GND
GND
TP256
0.1
C87
CFA4
CFA3
CFA2
+3.3V
0.1
C86
CFA20
CFA11
CFA10
CFA9
CFA8
CFA7
CFA6
CFA5
+3.3V
0.1
CFD7
CFD6
CFD5
CFD4
CFD3
CFD2
CFD1
CFD0
C82
18
17
16
15
14
13
12
11
20
10
VCC
GND
D1
D2
D3
D4
D5
D6
D7
D8
+3.3V
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U13
SN74LV367A_01
/1OE
/2OE
1A1
1A2
1A3
1A4
2A1
2A2
U15
GND
0.1
CFD15
CFD14
CFD13
CFD12
CFD11
CFD10
CFD9
CFD8
SN74LV245A_01
18
17
16
15
14
13
12
11
C81
VCC
GND
D1
D2
D3
D4
D5
D6
D7
D8
20
10
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U14
19
1
2
3
4
5
6
7
8
9
19
1
2
3
4
5
6
7
8
9
U12
TP378
TP379
TP380
TP381
TP382
TP383
TP384
TP385
(3) CDET1B
(3) CDET1A
(3) CFWAITN1
TP405
TP406
TP407
TP408
TP409
TP10
TP411
TP412
1
3
5
7
TP400
TP401
TP402
+3.3V
+3.3V
(3) CCFCSN1
(3) CFOEN1
CFD [15: 0]
CCFCSN1
CCFCSN2
CFA20
RA34
10kx4
TP387
CFA20
TP414
(3) CFRST1
CFA [11: 2]
TP404
(3) CFWEN1
CCFCSN2
0.1
0.1
GND
C84
C83
TP397
TP398
TP399
TP389
TP390
TP391
TP392
TP393
TP394
TP395
TP396
TP419
TP420
TP416
TP417
8TP18
2
4
6
8
1
3
5
7
(4, 5) LD [15: 0]
TP244
TP252
CFD8 TP254
CFD9
CFD10
TP250
TP248
TP246
CFD11
CFD12
CFD13
CFD14
CFD15
CFD0
CFD1
CFD2
CFD3
CFD4
CFD5
CFD6
CFD7
CFD7
CFD6
CFD5
CFD4
CFD3
CFD2
CFD10
CFD9
CFD8
CFD11
+3.3V
51
52
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
C79
22/6.3V
CONNECTOR CF-CARD
GND
D3
D4
D5
D6
D7
/CE1
A10
/OE
A9
A8
A7
VCC
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
WP
/CD2
/CD1
D11
D12
D13
D14
D15
/CE2
/VS1
/IORD
/IOWR
/WE
RDY//BSY
VCC
/CSEL
/VS2
RESET
/WAIT
/INPACK
/REG
BVD2
BVD1
D8
D9
D10
GND
YC05
FS-1800/1800N | FS-3800/3800N
TP277
(3) SVCCLK
TP280
TP282
TP283
TP284
TP285
TP286
(3, 12) BD
(3) FSYNC
(3, 4, 5) WEN0
(3, 4) OEN0
(3, 5) CSN2
(1, 2, 4) CPUD31
(1, 2, 4) CPUD30
(1, 2, 4) CPUD29
(1, 2, 4) CPUD28
(1, 2, 4) CPUD27
(1, 2, 4) CPUD26
(1, 2, 4) CPUD25
(1, 2, 4) CPUD24
(4, 5, 8) LA3
4, 5, 8) LA2
+XLI3.3V
FS-1800/1800N | FS-3800/3800N
A-26
GND
0.1
C96
0.1
C97
C98
0.1
LPVSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
LPVDD
VDD3
VDD3
VDD3
VDD3
VDD3
VDD3
VDD5
PVIDEO7
PVIDEO6
PVIDEO5
PVIDEO4
PVIDEO3
PVIDEO2
PVIDEO1
PVIDEO0
/LSYNC
/SRCCLK
VIDEO
EOP
52 PIN QFP
0.1
TEST
TEST
TEST
/RST
FT3
FT2
FT1
FT0
BD
FSYNC
CLK
/WR
/RD
/CS
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
PA1
PA0
U16
C95
+XLI3.3V
GND
17
16
15
21
51
50
46
43
33
14
49
41
40
12
37
30
29
28
27
26
25
22
39
38
TP600
Image Chip
23
48
47
35
34
20
9
8
24
45
32
31
18
6
5
19
52
1
2
3
4
7
10
11
42
44
36
13
+XLI3.3V
R232
GND
+5V
0.1
C92
0.047
C91
GND
C88
0.1
22/6.3V
CHIP
TANTAL
C94
TP560
22/6.3V
CHIP EL.
+ C180 +
TP551
R231
+XLI3.3V
TP261
TP262
TP263
TP264
TP265
TP266
TP267
TP268
TP552
TP276
TP275
TP269
TP270
TP279
GND
TP550
56
56
VIN
GND
ON/OFF
LP2981-3.3_01
NC
VOUT
U28
1
2
3
5V - 3.3V REGULATOR
PVIDEO7 (3)
PVIDEO6 (3)
PVIDEO5 (3)
PVIDEO4 (3)
PVIDEO3 (3)
PVIDEO2 (3)
PVIDEO1 (3)
PVIDEO0 (3)
R27
R28
TP271
TP272
GND
C93
+5V
SRCCLKN (3)
XLIDATA (3)
TP530
(3 SELECTIN
(3) STROBE
(12) AUTOFD
(3) INIT
(3) EXTIORC
(3) BUSY
(3) OPRSTN2
R260
2.2 k
(3) P1284HD
(3) ACK
(3)BUSY
(3) PERROR
(3) SELECT
(3) FAULT
(3) PDATA [ 8: 1]
1
2
4
5
9
10
12
13
VCC 14
GND 7
1Y 3
2Y 6
3Y 8
4Y 11
+3.3V
SN74LV00_01
1A
1B
2A
2B
3A
3B
4A
4B
U31
0.1
C102
TP319
PDATA7
PDATA8
PDATA3
PDATA4
PDATA5
PDATA6
PDATA1
PDATA2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
TP804
TP805
TP288
TP289
TP290
TP291
TP292
TP293
TP294
TP295
TP296
TP297
TP298
TP299
TP300
TP301
R302
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
0.1
C200
TP800
BUSYC
SN74LVC161284
DIR
Y9
Y10
Y11
Y12
Y13
VCC_C
B1
B2
GND
B3
B4
B5
B6
GND
B7
B8
VCC_C
PLout
C14
C15
C16
C17
HLin
IEEE 1284
Transceiver
+3.3V
HD
A9
A10
A11
A12
A13
VCC
A1
A2
GND
A3
A4
A5
A6
GND
A7
A8
VCC
PLin
A14
A15
A16
A17
HLout
0.1
C103
PNSELIN
PNSTROBE
PNAUTOFD
PNINIT
PPDATA7
PPDATA8
PPDATA3
PPDATA4
PPDATA5
PPDATA6
PPDATA1
PPDATA2
PNACK
PBUSY
PPERROR
PSELECT
PNFAULT
TP317
P1284DIR (3)
UDZS5.6
DZ01
HZM6.8FA
DZA01
1
2
3
5
4
1
2
HZM6.8FA HZM6.8FA
DZA02
DZA03
1
2
3
5
4
TP803
TP302
TP320
TP321
TP322
TP323
TP802
TP801
HZM6.8FA
DZA04
F01
TP318
+5V
(11) FUSED5V
+5V
TP324
TP325
TP326
TP327
TP328
1
2
3
5
RA37
2
4
6
8
1
3
5
7
1
2
3
5
4
TP303
TP304
TP305
TP306
TP307
TP308
TP309
TP310
TP311
TP312
TP313
TP314
TP315
TP316
PNSTROBE
PPDATA1
PPDATA2
PPDATA3
PPDATA4
PPDATA5
PPDATA6
PPDATA7
PPDATA8
PNACK
PBUSY
PPERROR
PSELECT
PNAUTOFD
PNSELIN
TP329
PNIINT
2.2kx4
U17
0
R32
+5V
TP421
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
STB
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
ACK
BUSY
PE
SEL
CAN
RMR
SG
FG
INIT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
ARARM
ASFON
FAULT
HSTI
EXPRM
PRDY
SELI
YC02
nStrobe
Data1(LSB)
Data2
Data3
Data4
Data5
Data6
Data7
Data8(MSB)
nAck
Busy
PError
Select
nAutoFd
Not difined
Logic Gnd
Chassis Gnd
Periferal Logic High
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
nInit
nFault
Not defined
Not defined
Not defined
nSelectin
FG
CONNECTOR PERALLEL-B
LP-U
LockPin(1)
LP-L
LockPin(36)
0
0
A-27
R33
R34
+3.3V
FS-1800/1800N | FS-3800/3800N
10k
C105
0.1
C107
0.1
(3) XRXD
(3) RSSEL
TP345
R39
FS-1800/1800N | FS-3800/3800N
A-28
CHIP EL.
100/16V
+5V
C110
0.1
GND
C112
GND
AIC1085-3.3CM
3 VCC OUT
1 GND
5V - 3.3V
REGULATOR
U20
1SS355
D03
2
+5V
TP343 TP344
SP01
SHORT PIN
1
2
3
TP341 TP342
GND
U18
0.1
D04
1
4
+5V
1SS355
GND
C111
CHIP EL.
220/6.3V
GND
V+
V-
SHDN
/EN
R1IN
R2IN
R3IN
T1OUT
T2OUT
T3OUT
T4OUT
11
15
21
20
4
23
16
2
3
1
24
GND
GND
A
B
Z
Y
R42
+2.5V
+5V
GND
R37
470
3
1
TP340
C106
0.1
TP336
R35
470
TP335
C115
0.1
1.8/2W
8
7
6
5
C108
0.1
MAX488CSA_02
VCC
GND
DI
RO
U19E
MAX206CAG
+5V
VCC
C2+
C2-
C1+
C1-
R1OUT
R2OUT
R3OUT
T1IN
T2IN
T3IN
T4IN
+3.3V
+3.3V
C109
13
14
10
12
5
22
17
(3) XCTS
(3) XDSR
SP01
SHORT PIN
7
8
9
7
6
18
19
TP330
TP331
TP332
TP333
TP334
(3) XTXD
(3) XDTR
(3) XRTS
C104
0.1
+5V
1SS355
D02
L1087DTX-ADJ
VCC OUT
GND
5V - 2.5V
REGULATOR
U21
R36
100/0.5W
Chip R.
GND
DZ05
UDZ18B
1
DZ02 2
UDZ18B
R44
1k
R43
1k
TP337
TP351
C116
0.1
GND
TP347
(10) FUSED5V
GND
DZ06
UDZ18B
C114
CHIP EL.
220/6.3V
+2.5V
SP01
SHORT PIN
4
5
6
DZ03
UDZ18B
DZ07
UDZ18B
TP338
DZ04
UDZ18B
R38
GND
BK1608HS241
TP339
FG
TXD
RXD/RDA
RTS
CTS
DSR
SG
DTR
RDB
SDA
SDB
Fused5V
YC03
GND
CONNECTOR 12PIN
1
2
3
4
5
6
7
8
9
10
11
12
0.1
C118
1A
1B
2A
2B
3A
3B
4A
4B
GND
4Y
3Y
2Y
1Y
1
2
3
4
5
1
2
3
4
5
YC08T
11
GND
TP512
TP515
TP514
TP513
WAUTOFD (3)
CONNCETOR 5PIN
B5B-PH-K-S
SN74LV08A_01
14 VCC
GND
1
2
4
5
9
10
12
13
TP510
10k
10k
(3) OPRDY2
(10) AUTOFD
+3.3V
(3) DBTXD
(3) DBRXD
(3) DBCLK
R41
R40
+5V
TP348
TP349
TP350
(3) FPDIR
(3) FPCLK
(3) FPDAT
(3) RSTIN
TP364
TP532
TP531
TP360
(3) VDOUTN
(3) VDOUTP
(3) SBSY
(3) VDFON
(3) SO
(3, 9) BD
(3) SI
(3) SDIR
(3) SCLK
(3) ENGIRN
2
4
6
8
2
4
6
8
2.2kx4
RA39
TP356
TP503
TP504
TP505
TP352
TP500
TP501
TP502
1 56kx4
3
5
7
1 56kx4
3
5
7
RA41 2
4
6
8
RA42 2
4
6
8
1 56kx4
3
5
7
RA40 2
4
6
8
GND
CHIP EL.
100/16V
GND GND
GND GND
GND
GND
GND GND
GND GND
GND GND
GND GND
GND
C124 C125 C126 C127 C128 C129 C130 C131 C132 C133 C134
1
3
5
7
RA39
100P 100P 100P 100P 100P 100P 100P 100P 100P 100P 100P
2.2kx4
1
3
5
7
(3) EXTIOR2
1
3
5
7
RA47
ACA3216MMM4S-600
2
4
6
8
RA45
ACA3216MMM4S-600
2
1
4
3
6
5
8
7
RA49
0
0
RA46
RA48
C117
BK2125HM601
R52
+5V
0
R53
A-29
R54
+3.3V
GND
Lock Pin
Lock Pin
1
2
3
4
5
6
7
8
9
10
11
12
YC07
24V
5V
SCLK
SDI
SDO
READY
24VGND
PFSEL
OPSEL0
OPSEL1
OPSEL2
GND
CONNECTOR OPTION I/F_01
OP5V
OPSCLK
OPSDI
OPSDO
OPREADY
OP24VGND
OPPFSEL
OPSEL0
OPSEL1
OPSEL2
R55
0
YC01
GND
GND
5V
5V
5V
SI
SDIR
SCLK
ESGIR
SBSY
VDFON
SO
GND
RESET
GND
PDOUT
GND
GND
GND
VDATAP
GND
VDATN
FPDIR
GND
FPPOWER
FPCLK
GND
FPDAT
SEL2
GND
SEL0
SEL1
GND(24)
PFSEL
SDO
READY
SCLK
SDI
24V
5V
CONNECTOR ENGINE40_01
G1
G2
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
BK2125HM601
R47
+3.3V
FS-1800/1800N | FS-3800/3800N
1000/6.3V
CHIP EL.
C03
1
3
5
7
2
4
6
8
2
4
6
8
2
4
6
8
1
3
5
7
1
3
5
7
GND
GND
C04
0.1
+CPU2.5V
C05
0.1
C06
0.1
C07
0.1
C08
0.1
TP80
C07
E05
E07
E10
E12
G03
G05
G12
G14
K03
K05
K12
K14
M05
M07
M10
M12
P07
P10
U01-3
+3.3V
+2.5V
+2.5V
C09
0.1
GND
C10
0.1
+3.3V
10
C12
0.1
C13
0.1
GND
ARTRYN
C01
10/16V
CHIP EL.
C11
0.1
R07
TP76
C14
0.1
GND
(2) AACKN
CABBN
APALL
C15
0.1
C02
0.1
TP5
TP6
TP7
TP8
TP1
TP2
TP3
TP4
CPUA31
CPUA30
CPUA29
CPUA28
CPUA27
CPUA26
CPUA25
CPUA24
CPUA23
CPUA22
CPUA21
CPUA20
CPUA19
CPUA18
CPUA17
CPUA16
CPUA15
CPUA14
CPUA13
CPUA12
CPUA11
CPUA10
CPUA9
CPUA8
CPUA7
CPUA6
CPUA5
CPUA4
CPUA3
CPUA2
CPUA1
CPUA0
(2) BGN
2
4
6
8
1
3
5
7
RA03
56x4
2
4
6
8
DBBN
TT3
TT1
ABBN
+CPU2.5V
+3.3V
PPC740G200_1
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
OVDD
PPC740G200_1
U01-2
F06
VDD
F08
VDD
F09
VDD
F11
VDD
G07
VDD
G10
VDD
H06
VDD
H08
VDD
H09
VDD
H11
VDD
J06
VDD
J08
VDD
J09
VDD
J11
VDD
K07
VDD
K10
VDD
L06
VDD
L08
VDD
L09
VDD
L11
VDD
+CPU2.5V
CDBBN
L2TSTCLK
CTT0
TSN
CTSIZ2
CTBSTN
CTSIZ1
CTSIZ0
CABBN
QREQN
ARTRYN
GBLN
CTT4
CTT2
CTT1
CTT3
PPC740G200_1
U01-4
C05
GND
C12
GND
E03
GND
E06
GND
E08
GND
E09
GND
E11
GND
E14
GND
F05
GND
F07
GND
F10
GND
F12
GND
G06
GND
G08
GND
G09
GND
G11
GND
H05
GND
H07
GND
H10
GND
H12
GND
J05
GND
J07
GND
J10
GND
J12
GND
K06
GND
K08
GND
K09
GND
K11
GND
L05
GND
L07
GND
L10
GND
L12
GND
M03
GND
M06
GND
M08
GND
M09
GND
M11
GND
M14
GND
P05
GND
P12
GND
GND
RA09
10x4
RA08
10x4
RA06
10x4
RA05
10x4
2
4
6
8
1
3
5
7
LL1TSTCLK
LSSDMOD
DPALL
APALL
RA02
10x4
2
4
6
8
1
3
5
7
R05
RA01
56x4
TP77
TP78
TP75
TP35
TP37
TP39
TP41
TP43
TP44
TP45
TP46
TP47
TP48
TP49
TP50
TP52
TP53
TP54
TP55
TP56
TP57
TP58
TP59
TP60
TP61
TP62
TP63
TP64
TP65
TP66
TP67
TP68
TP69
TP70
TP71
TP72
TP73
TP74
C16
E04
D13
F02
D14
G01
D15
EP2
D16
D04
E13
G02
E15
H01
E16
H02
F13
J01
F14
J02
F15
H03
F16
F04
G13
K01
G15
K02
H16
M01
J15
P01
L02
K04
C01
B04
B03
B02
A04
J04
A10
L01
B06
E01
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
/AACK
/ABB
AP0
AP1
AP2
AP3
/APE
/ARTRY
AVDD
/BG
/BR
/CI
U01-1
QREQN
(2, 4, 9, 10) RSTOUTN
(3) BCLK
(2) TAN
CTBSTN
(12) TCK
(12) TDI
(12) TDO
(2) TEAN
(2, 4, 9, 10) RSTOUTN
(12) TMS
(2, 4, 9, 10) RSTOUTN
TSN
CTSIZ0
CTSIZ1
CTSIZ2
CTT0
CTT1
CTT2
CTT3
CTT4
(12) CKSTPN
CDBBN
(2) DBGN
(2, 9) RSTOUTN
GBLN
DBBN (2)
TT3 (2)
TT1 (2)
ABBN (2)
TSIZ2 (2)
TSIZ1 (2)
TSIZ0 (2)
TBSTN (2)
TP113
TP114
TP115
TP116
TP117
1
3
5
7
TP9
TP10
TP11
TP118
R06
+3.3V
RA04
10kx4
TP28
TSIZ2
TSIZ1
TSIZ0
TBSTN
TP79
2
4
6
8
1
3
5
7
TP29
TP30
TP31
TP32
TP33
TP25
TP26
TP27
TP22
TP23
TP21
TP19
TP20
TP15
TP16
TP13
J16
H04
D06
D05
C08
C06
C03
B08
B07
F03
D02
C15
C14
B16
A15
B13
B12
D10
A13
J13
C10
B11
C04
H13
A12
A11
C11
A03
A02
A14
C02
H14
C09
B14
A16
D02
J03
D03
A08
B09
A09
D09
C13
B10
TP34
PPC740G
200MHz
D12
D11
B15
A07
R02
M04
P02
R01
L04
N02
L03
M02
T04
TP5
N05
R05
T06
R06
N06
P06
T07
R07
N07
T08
R08
N08
P08
T09
R09
T10
N09
P09
R10
T11
T12
R11
N11
P11
R12
R13
T15
R15
T16
P14
+3.3V
TP36
TP37
TP40
TP42
TP51
CPUD0
CPUD1
CPUD2
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
CPUD8
CPUD9
CPUD10
CPUD11
CPUD12
CPUD13
CPUD14
CPUD15
CPUD16
CPUD17
CPUD18
CPUD19
CPUD20
CPUD21
CPUD22
CPUD23
CPUD24
CPUD25
CPUD26
CPUD27
CPUD28
CPUD29
CPUD30
CPUD31
LSSDMCD
PPC740G200_1
L2TSTCLK
L1TSTCLK
INT
/HRESET
DP7
DP6
DP5
DP4
DP3
DP2
DP1
DP0
DH31
DH30
DH29
DH28
DH27
DH26
DH25
DH24
DH23
DH22
DH21
DH20
DH19
DH18
DH17
DH16
DH15
DH14
DH13
DH12
DH11
DH10
DH9
DH8
DH7
DH6
DH5
DH4
DH3
DH2
DH1
DH0
NC
NC
NC
NC
NC
NC
NC
NC
NC
VOLTDET
WT
TT4
TT3
TT2
TT1
TT0
TSIZ2
TSIZ1
TSIZ0
TS
TRST
TMS
TLBISYN
TEA
TDO
TDI
TCK
TC1
TC0
TBST
TBEN
TA
SYSCLK
SRESET
SMI
RSRV
QREQ
QACK
PLLCFG0
PLLCFG1
PLLCFG2
PLLCFG3
MCP
LSSMOD
/CKSTP1
/CKSTPO
CLKO
CSE0
CSE1
/DBB
/DBG
/DBIS
/DBWO
/DPE
/DRTRY
GBL
DL0
DL1
DL2
DL3
DL4
DL5
DL6
DL7
DL8
DL9
DL10
DL11
DL12
DL13
DL14
DL15
DL16
DL17
DL18
DL19
DL20
DL21
DL22
DL23
DL24
DL25
DL26
DL27
DL28
DL29
DL30
DL31
A-30
D08
A06
D07
B01
B05
J14
N01
H15
G04
A05
G16
F01
K13
K15
K16
L16
L15
L13
L14
M16
M15
M13
N16
N15
N13
N14
P16
P15
R16
R14
T14
N10
P13
N13
T13
P03
N03
N04
R03
T01
T02
P04
T03
R04
FS-1800/1800N | FS-3800/3800N
TP81
TP82
TP83
TP84
TP85
TP86
TP87
TP88
TP89
TP90
TP91
TP92
TP93
TP94
TP95
TP96
TP97
TP98
TP99
TP100
TP101
TP102
TP103
TP104
TP105
TP106
TP107
TP108
TP109
TP110
TP111
TP112
+3.3V
DPALL
L2TSTCLK
L2TSTCLK
CPUINTN (2)
RSTOUTN (2, 4, 9, 10)
A-31
(1) BGN
(1) ABBN
(1) AACKN
(1) DBGN
(1) DBBN
(1) TT1
(1) TT3
(1) TSIZ0
(1) TSIZ1
(1) TSIZ2
(1) TAN
(1) TEAN
(1) TBSTN
(1) CPUINTN
(1, 4, 9, 10) RSTOUTN
TP155
+3.3V
CPUD0
CPUD1
CPUD2
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
CPUD8
CPUD9
CPUD10
CPUD11
CPUD12
CPUD13
CPU D14
CPUD15
CPUD16
CPUD17
CPUD18
CPUD19
CPUD20
CPUD21
CPUD22
CPUD23
CPUD24
CPUD25
CPUD26
CPUD27
CPUD28
CPUD29
CPUD30
CPUD31
AF21
AE20
AD14
AC15
AE16
AE15
AC17
AD18
AF15
AD17
AE17
AF17
AD16
AE18
AF18
AF16
AA24
AA25
AA26
AB23
AB24
AB25
AB26
AC24
AC25
AC26
AD24
AD25
AD26
AE25
AE25
AF25
AE14
AF14
AD13
AE13
AF13
AC12
AD12
AE12
AF12
AD11
AE11
AF11
AC10
AD10
AF10
AD9
CPUA0 AC2
CPUA1 AC1
CPUA2 AD3
CPUA3 AD2
CPUA4 AD1
CPUA5 AE2
CPUA6 AE1
CPUA7 AF2
CPUA8 AE3
CPUA9 AF3
CPUA10 AD4
CPUA11 AE4
CPUA12 AF4
CPUA13 AC5
CPU A14 AD5
CPUA15 AE5
CPUA16 AF5
CPUA17 AD6
CPUA18 AE6
CPUA19 AF6
CPUA20 AC7
CPUA21 AD7
CPUA22 AE7
CPUA23 AF7
CPUA24 AD8
CPUA25 AE8
CPUA26 AF8
CPUA27 AE9
CPUA28 AF9
CPUA31 AE10
CPUINT
RSTOUTX
BGN
BRN
ABBN
AACKN
DBGN
DBBN
TT1
TT3
TSIZ0
TSIZ1
TSIZ2
TAN
TEAN
TBST
CPUD0
CPUD1
CPUD2
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
CPUD8
CPUD9
CPUD10
CPUD11
CPUD12
CPUD13
CPUD14
CPUD15
CPUD16
CPUD17
CPUD18
CPUD19
CPUD20
CPUD21
CPUD22
CPUD23
CPUD24
CPUD25
CPUD26
CPUD27
CPUD28
CPUD29
CPUD30
CPUD31
CPUA0
CPUA1
CPUA2
CPUA3
CPUA4
CPUA5
CPUA6
CPUA7
CPUA8
CPUA9
CPUA10
CPUA11
CPUA12
CPUA13
CPUA14
CPUA15
CPUA16
CPUA17
CPUA18
CPUA19
CPUA20
CPUA21
CPUA22
CPUA23
CPUA24
CPUA25
CPUA26
CPUA27
CPUA28
CPUA31
U02-1
ASIC
Block1/2
ASDA0
ASDA1
ASDA2
ASDA3
ASDA4
ASDA5
ASDA6
ASDA7
ASDA8
ASDA9
ASDA10
ASDA11
ASDA12
ASDBA0
ASDBA1
ASDCSN0
ASDCSN1
ASDCSN2
ASDCSN3
ASDCSN4
ASDCSN5
C25
E25
C24
F24
B26
E23
B25
D26
A25
D25
A24
C26
A21
D24
C22
C21
A20
A19
B19
A18
B18
MB87J4300
BIU603
SIDIR
SIOEN
ALATCH
EXTBDIR
EXTBOEN
SDD0
SDD0
SDD1
SDD1
SDD2
SDD2
SDD3
SDD3
SDD4
SDD4
SDD5
SDD5
SDD6
SDD6
SDD7
SDD7
SDD8
SDD8
SDD9
SDD9
SDD10
SDD10
SDD11
SDD11
SDD12
SDD12
SDD13
SDD13
SDD14
SDD14
SDD15
SDD15
SDD16
SDD16
SDD17
SDD17
SDD18
SDD18
SDD19
SDD19
SDD20
SDD20
SDD21
SDD21
SDD22
SDD22
SDD23
SDD23
SDD24
SDD24
SDD25
SDD25
SDD26
SDD26
SDD27
SDD27
SDD28
SDD28
SDD29
SDD29
SDD30
SDD30
SDD31
SDD31
ASDD0
ASDD1
ASDD2
ASDD3
ASDD4
ASDD5
ASDD6
ASDD7
ASDD8
ASDD9
ASDD10
ASDD11
ASDD12
ASDD13
ASDD14
ASDD15
ASDD16
ASDD17
ASDD18
ASDD19
ASDD20
ASDD21
ASDD22
ASDD23
ASDD24
ASDD25
ASDD26
ASDD27
ASDD28
ASDD29
ASDD30
ASDD31
D10
AC20
AD15
AC3
AD19
AE19
A12
A13
B13
C13
A14
B14
A15
B15
D15
A16
B16
C16
A17
B17
C17
D17
J25
J26
K23
K24
K25
K26
L25
L26
F25
F26
G23
G25
G26
H24
H25
H26
C15 ADDQMLL
DQM0
C18 ADDQMLM
DQM1
J24 ADDQMUM
DQM2
E26 ADDQMUU
DQM3
B12
IICSDA
A11
IICSCL
D20 ASDCKE
CKE
B20
SDCLKIN
B21
SDCLKOUT
B23 ASDCASN
SDCASN
D22 ASDRASN
SDRASN
C19 ASDWEN
SDWEN
SDCSN0
SDCSN1
SDCSN2
SDCSN3
SDCSN4
SDCSN5
SDA0
SDA1
SDA2
SDA3
SDA4
SDA5
SDA6
SDA7
SDA8
SDA9
SDA10
SDA11
SDA12
SDBA0
SDBA1
TP127
TP153
TP154
+3.3V
EXTBDIR (4)
EXTBOEN (4, 8)
ALATCH (4)
TP131
C42
220/6.3V
SDCLKOUT
TP136
TP123
TP145
TP119
TP156
TP157
TP158
TP137
TP141
TP146
TP147
TP148
GND
C43
GND
C49
0.1
+3.3V
0.1
+ASIC2.5V
SDA8
SDA9
SDA10
SDA11
RA19 0x4
7
8
5
6
3
4
1
2
RA21 0x4
1
2
3
4
5
6
7
8
C50
0.1
C44
0.1
C51
0.1
C45
0.1
C52
0.1
C46
0.1
ACB1608H-060
RA23 0x4
7
8
5
6
3
4
1
2
R11
RA22 0x4
1
2
3
4
5
6
7
8
SDA4
SDA5
SDA6
SDA7
RA18 0x4
7
8
5
6
3
4
1
2
C53
0.1
C47
0.1
C54
0.1
C48
0.1
DQMLL (6, 7)
DQMLM (6, 7)
DQMUM (6, 7)
DQMUU (6, 7)
SDCLK (6, 7)
SDCASN (6, 7)
SDRASN (6, 7)
SDWEN (6, 7)
SDCKE (6, 7)
SDCSN2
SDCSN3
SDCSN4
SDCSN5
RA20 0x4
SDA12
7
8
SDBA0
5
6
SDBA1
3
4
1
2 SDCSN0
SDA0
SDA1
SDA2
SDA3
0x4
8
6
4
2
RA17
7
5
3
1
C140
0.1
1k
R09
1k
+3.3V
C28
GND
C29
100p 100p
R08
SDCSN2 (7)
SDCSN3 (7)
SDCSN4 (7)
SDCSN5 (7)
SDBA0 (6, 7)
SDBA1 (6, 7)
SDCSN0 (6)
TP135
IICSDA (7)
IICSDL (7)
GND
A1
A26
D6
D11
D16
D21
F4
F23
L4
L23
T4
T23
AA4
AA23
AC6
AC11
AC16
AC21
AF1
AF26
A23
C5
C14
C20
C23
G24
M3
R24
MB87J4300
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
OVSS
OVSS
OVSS
OVSS
OVSS
OVSS
OVSS
OVSS
U02-5
M4 AGND
N3 AGND
P2 AGND
R26 AGND
+2.5V
MB87J4300
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
VDDE5
OVDDE5
OVDDE5
OVDDE5
OVDDE5
VDDE5
OVDDE5
OVDDE5
TP152
D4
D9
D13
D18
D23
J4
J23
N23
P4
V4
V23
AC4
AC9
AC14
AC18
AC23
MB87J4300
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
VDDEI
U02-4
N1 AVDD
N2 AVDD
P3 AVDD
U26 AVDD
+ASIC2.5V
R10
ACB1608H-060
D14
D19
H4
H23
N4
P23
W4
W23
AC8
AC13
AC19
U02-3
A22
B22
B24
D5
D8
F24
Y23
+3.3V
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-32
(10) OPRSTN2
(12) OPRDY2
TP183
TP182
TP191
(12) FPDAT
(12) FPCLK
(12) FPDIR
(8) CFRST1
(8) CFRST2
(8) CFCSN1
(8) CFCSN2
(8) CFOEN1
(8) CFOEN2
(8) CFWEN1
(8) CFWEN2
(8) CFWAITAN1
(8) CFWAITBN2
(8) CDET1A
(8) CDET1B
(8) CDET2A
(8) CDET2B
(5) OPRST1
(5) OPRDY1
(5) DMAACKN1
TP178
TP180
(5) DMAREQ1
(5) IORN1
TP172
TP174
(5) IOWN1
TP175
TP176
(5) OP1RN1
(5) KUIOCSN1
TP169
TP170
(5) IODATACKN1
(11) XTXD
(11) XRXD
(11) XRTS
(11) XCTS
(11) XDSR
(11) XDTR
(11) RSSEL
(10) ACK
(10) BUSY
(10) PERROR
(10) SELECT
(10) FAULT
(10) STROBE
(10) AUTOFD
(10) INIT
(10) SELECTION
(10) P1284DIR
(10) P1284HD
PDATA1
PDATA2
PDATA3
PDATA4
PDATA5
PDATA6
PDATA7
PDATA8
GND
G4
A5
C6
B6
A6
A7
J2
J3
G1
G3
H1
H2
H3
J1
K1
K2
F1
K3
G2
K4
M25
M24
M24
T25
U25
V25
N26
P26
P24
R25
T24
R23
W26
W25
Y24
M26
N25
N24
U24
V24
U23
V26
W24
Y26
Y25
R1
P1
T2
R4
R2
R3
T3
Y1
W3
W2
W1
V3
V2
V1
U4
AA2
AA1
Y4
Y3
Y2
U1
U2
T1
U3
AB1
AA3
PCTEST
TSTMODE
FPRST
FPDAT
FPCLK
FPDIR
RSTA
RSTB
CFCSN1
CFCSN2
CFOEN1
CFOEN2
CFWEN1
CFWEN2
WAITAN
WAITBN
CDET1A
CDET1B
CDET2A
CDET2B
KUIOCSN1
KUIOCSN2
KUIOCSN3
IODATACKN1
IODATACKN2
IODATACKN3
IORN1
IORN2
IORN3
IOWN1
IOWN2
IOWN3
OP1RN1
OP1RN2
OP1RN3
DMAACK1
DMAACK2
DMAACK3
DMAREQ1
DMAREQ2
DMAREQ3
OPRDY1
OPRDY2
OPRST1
OPRST2
TXD
RXD
RTS
CTS
DSR
DTR
RSSEL
PAD0
PAD1
PAD2
PAD3
PAD4
PAD5
PAD6
PAD7
ACK
BUSY
PERROR
SELECT
FAULT
STROBE
AUTOFD
INIT
SELECTION
P1284DIR
P1284HD
U02-2
Waverly
(352BGA)
block2/2
ASIC
Block 2/2
C10
C9
B10
A10
C12
B7
A8
B5
A4
B2
B3
B4
C3
A2
C2
C4
A3
B1
D2
E1
C1
D1
D3
E2
E3
E4
F2
F3
M1
L2
M2
B11
C11
D12
L1
L3
T26
P25
D7
A9
L24
AF20
AF19
AB2
AB3
AB4
B8
C8
C7
B9
AF24
AF24
AD23
AF23
AD20
AF21
AD21
AF22
AF22
AD22
AF23
AC22
MB87J4300
ENGIRN
SBSY
SDIR
SCLK
SI
SO
RSTINX
VDFONSPL0
VDFONSPL1
VDATA0
VDATAN0
VDATAP0
VDATAN1
VDATAP1
BD
BIASP
BIASN
SVCCLK
AUXIN
AUXCLK
AUXOUT0
AUXOUT1
AUXOUT2
AUXOUT3
AUXOUT4
AUXOUT5
AUXOUT6
AUXOUT7
XTST
XSM
MST
SMCK
EXTIOR1
EXTIOR2
VXIN
VXOUT
CXIN
CXOUT
CXX2
PLGCLK
OPBCLK
BCLKIN
BCLKOUT
DBCLK
DBTXD
DBRXD
VBUS
USBDP
USBDN
CLK48IN
ROMA1
ROMA2
ROMA3
ROMA4
ROMCSN0
ROMCSN1
ROMCSN2
ROMCSN3
ROMOEN0
ROMOEN1
ROMWEN0
ROMWEN1
VDATAN
VDATAP
ROMA1
ROMA2
ROMA3
ROMA4
CSN0
CSN1
CSN2
CSN3
OEN0
OEN1
WEN0
WEN1
27
+3.3V
TP173
TP376
TP171
TP168
TP167
ENGIRN (12)
SBSY (12)
SDIR (12)
SCLK (12)
SI (12)
SO (12)
RSTIN (12)
TP187
TP188
BD (9, 12)
VDFON (12)
FSYNC (9)
TP186
XLIDATA (9)
SRCCLKN (9)
PVIDEO0 (9)
PVIDEO1 (9)
PVIDEO2 (9)
PVIDEO3 (9)
PVIDEO4 (9)
PVIDEO5 (9)
PVIDEO6 (9)
PVIDEO7 (9)
R19
SELECTIN (10)
R14
TP165
TP166
DBCLK (12)
DBTXD (12)
DBRXD (12)
TP159
ROMA1 (5)
ROMA2 (4)
ROMA3 (4)
ROMA4 (4)
CSN0 (4)
CSN1 (4)
CSN2 (5, 9)
CSN3 (5)
CSN0 (4, 9)
CSN1 (5)
WEN0 (4, 5, 9)
TP164
TP179
TP193
0.1
GND
C60
R20
SVCCLK (9)
3.3k
R210
0.1
L03
TP372
ACM3225-102_01
6
4
2
8
100F
TP374
R15
10kx4
RA24
CHOKE-COIL
GND
C61
TP184
R21
430F
R16
+3.3V
EXTIORC (10)
TP190
TP181
TP160
TP161
TP162
TP163
BCLK (1)
5
3
1
7
R17
TP375
TP185
GND
240F
VDOUTP (12)
330
25.0000MHz
X01
VDOUTN (12)
R22
+3.3V
+3.3V
0
R12
(10) PDATA [ 8: 1]
+3.3V
C56
C55
C58
TP377
25.76930MHz
C59
X02
10p
10p
22p
22p
GND
GND
A-33
(2) ALATCH
CPUA5
CPUA4
CPUA3
CPUA2
CPUA14
CPUA13
CPUA12
CPUA11
CPUA10
CPUA9
CPUA8
CPUA7
CPUA22
CPUA21
CPUA20
CPUA19
CPUA18
CPUA17
CPUA16
CPUA15
GND
GND
GND
1
11
3
4
7
8
13
14
17
18
1
11
3
4
7
8
13
14
17
18
1
11
3
4
7
8
13
14
17
18
VCC
GND
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
20
10
2
5
6
9
12
15
16
19
VCC
GND
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
20
10
2
5
6
9
12
15
16
19
VCC
GND
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
20
10
2
5
6
9
12
15
16
19
SN74LV373A_01
/OE
LE
D0
D1
D2
D3
D4
D5
D6
D7
U05
SN74LV373A_01
/OE
LE
D0
D1
D2
D3
D4
D5
D6
D7
U04
SN74LV373A_01
/OE
LE
D0
D1
D2
D3
D4
D5
D6
D7
U03
C65
0.1
+3.3V
C64
0.1
LA6
LA5
LA4
LA3
LA2
TP200
TP201
TP202
(3, 5, 9) WEN0
(3, 9) OEN0
(3) CSN0
(3) CSN1
TP206
TP205
TP204
TP203
TP199
TP198
TP197
TP196
TP194
+3.3V
(3) ROMA2
(3) ROMA3
(3) ROMA4
TP195
LA14
LA13
LA12
LA11
LA10
LA9
LA8
LA7
LA22
LA21
LA20
LA19
LA18
LA17
LA16
LA15
C63
0.1
+3.3V
C62
LA5
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
CPUD0
CPUD1
CPUD2
LA19
LA20
LA21
LA22
LA15
LA16
LA17
LA18
CPUD24
CPUD25
CPUD26
CPUD27
CPUD28
CPUD29
CPUD30
CPUD31
CPUD20
CPUD21
CPUD22
CPUD23
LA13
LA14
CPUD16
CPUD17
CPUD18
CPUD19
LA10
LA11
LA12
CPUD8
CPUD9
CPUD10
CPUD11
CPUD12
CPUD13
CPUD14
CPUD15
LA6
LA7
LA8
LA9
GND
22/6.3V
CHIP EL.
GND
+3.3V
System
(ROM)
DIMM
YS01
CONNECTOR 72PIN
1
2 GND
3 DQ0
4 DQ1
5 DQ2
6 VCC
7 DQ3
8 DQ4
9 DQ5
10 DQ6
11 DQ7
12 GND
13 A2
14 A3
15 A4
16 A5
17 NC
(2, 8) EXTBOEN
18 A6
(2) EXTBDIR
19 A7
20 A8
21 A9
22 GND
23 DQ8
24 DQ9
25 DQ10
26 DQ11
27 DQ12
28 DQ13
29 DQ14
30 DQ15
31 VCC
32 A10
33 A11
34 A12
35 NC
36 DQ16
37 DQ17
38 DQ18
39 DQ19
40 GND
41 OEN
42 CE1N
43 CE2N
44 A13
45 A14
46 NC
47 NC
48 WEN
49 VCC
50 DQ20
51 DQ21
52 DQ22
53 DQ23
54 GND
55 DQ24
56 DQ25
57 DQ26
58 DQ27
59 DQ28
60 DQ29
61 DQ30
62 DQ31
63 VCC
64 A15
65 A16
66 A17
67 A18
68 NC
69 A19
70 A20
71 A21
72 A22
GND
CPUD7
CPUD6
CPUD5
CPUD4
CPUD3
CPUD2
CPUD1
CPUD0
CPUD15
CPUD14
CPUD13
CPUD12
CPUD11
CPUD10
CPUD9
CPUD8
19
1
2
3
4
5
6
7
8
9
19
1
2
3
4
5
6
7
8
9
GND
VCC
GND
B1
B2
B3
B4
B5
B6
B7
B8
20
10
18
17
16
15
14
13
12
11
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U07
GND
0.1
C67
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
+3.3V
0.1
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
C66
18
17
16
15
14
13
12
11
20
10
VCC
GND
B1
B2
B3
B4
B5
B6
B7
B8
+3.3V
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U06
LD [15: 0]
LD [15: 0] (5, 8)
LA [22: 2] (5, 8, 9)
FS-1800/1800N | FS-3800/3800N
(4, 8) LA20
R110
(3) ROMA1
(4, 8) LD [15: 0]
(4, 8, 9) LA [22: 0]
ALA20
LA19
LA18
LA17
LA16
LA15
LA14
LA13
LA12
LA11
LA10
LA9
LA8
LA7
LA6
LA5
LA4
LA3
LA2
TP207
LA21
LA20
LA19
LA18
LA17
LA16
LA15
LA14
LA13
LA12
LA11
LA10
LA9
LA8
LA7
LA6
LA5
LA4
LA3
LA2
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
FS-1800/1800N | FS-3800/3800N
A-34
13
32
12
14
33
31
29
27
A5
22
20
18
16
30
28
26
24
21
19
17
15
GND
GND
/CE
/OE
/BYTE
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
12
31
11
13
32
30
28
26
24
21
19
17
15
29
27
25
23
20
18
16
14
VCC
U09S
42
1 A19
2 A18
33 A17
34 A16
35 A15
36 A14
37 A13
38 A12
39 A11
40 A10
41 A9
3 A8
4 A7
5 A6
6 A5
7 A4
8 A3
9 A2
10 A1
A0
22
GND
GND
/CE
/OE
/BYTE
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MX23L1610MC10KF2
1
NU
23
VCC
44
43
2
3
34
35
36
37
38
39
40
41
42
4
5
6
7
8
9
10
11
U08
GND
C69
CSN3
OEN1
+3.3V
0.1
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
GND
C68
0.1
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
+3.3V
CSN3 (3)
OEN1 (3)
CSN2 (3, 9)
OEN1 (3)
C72
+5V
1
3
5
7
BA033FP
C70
22/6.3V
5V - 3.3V REGULATOR
U24
3
1
2 IN OUT
COM
D01 1SS355
2
1
(3) DMAACKN1
(3) IORN1
(3) IOWN1
(3) OPRSTN1
(3) OPRDY1
(3) DMAREQ1
(3) KUIOCSN1
(3) IODTACKN1
(3) OPIRN1
+3.3V
GND
2
4
6
8
GND
C71
0.1
+KUIO3.3V
2.2kx4
RA25
LA16
LA8
LA7
LA6
LA5
LA4
LA3
LA2
LA15
LA14
LA13
LA12
LA11
LA10
LA9
+5V
GND
+KUIO3.3V
G1
G2
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A21
B21
A22
B22
A23
B23
A24
B24
A25
B25
A26
B26
A27
B27
A28
B28
A29
B29
A30
B30
CONNCTOR KUIO
LockPin(A1)
LockPin(A30)
NC
NC
NC
NC
GND
Power 3.3V
Power 3.3V
A15
GND
A14
A13
A12
A11
A10
A9
A8
GND
A7
A6
A5
A4
A3
A2
A1
GND
Power 3.3V
/OP2IF
/OP2ACK
/OP2IR
Power 5V
RDY
DREQ
GND
/DMACK
/IOR
/IOW
/RESET
VOLT DETECT
D15
D14
GND
D13
D12
D11
D10
D9
D8
D7
GND
D6
D5
D4
D3
D2
D1
D0
GND
NC
NC
NC
YC04
KUIO-LV
A-35
ASDD22
ASDD30
ASDD23
ASDD31
ASDD20
ASDD28
ASDD21
ASDD29
ASDD18
ASDD26
ASDD19
ASDD27
ASDD16
ASDD24
ASDD17
ASDD25
ASDD6
ASDD14
ASDD7
ASDD15
ASDD4
ASDD12
ASDD5
ASDD13
ASDD2
ASDD10
ASDD3
ASDD11
ASDD0
ASDD8
ASDD1
ASDD9
TP240
TP236
TP232
TP224
TP220
TP216
TP212
RA33 56x4
2
1
4
3
6
5
8
7
RA32 56x4
2
1
4
3
6
5
8
7
RA31 56x4
2
1
4
3
6
5
8
7
RA30 56x4
2
1
4
3
6
5
8
7
RA29 56x4
2
1
4
3
6
5
8
7
RA28 56x4
2
1
4
3
6
5
8
7
RA27 56x4
2
1
4
3
6
5
8
7
RA26 56x4
2
1
4
3
6
5
8
7
SDD22
SDD30
SDD23
SDD31
SDD20
SDD28
SDD21
SDD29
SDD18
SDD26
SDD19
SDD27
SDD16
SDD24
SDD17
SDD25
SDD6
SDD14
SDD7
SDD15
SDD4
SDD12
SDD5
SDD13
SDD2
SDD10
SDD3
SDD11
SDD0
SDD8
SDD1
SDD9
(2) SDCAN0
(2, 7) SDRASN
(2, 7) SDCASN
(2, 7) SDWEN
SDD31
SDD30
SDD29
SDD28
SDD27
SDD26
SDD25
SDD24
SDD23
SDD22
SDD21
SDD20
SDD19
SDD18
SDD17
SDD16
C74
0.1
C73
0.1
+3.3V
1
14
27
3
9
43
49
19
18
17
16
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
VSS
VSS
VSS
VSSQ
VSSQ
VSSQ
VSSQ
NC
NC(RFU)
CLK
CKE
DQML
DQMU
28
41
54
6
12
46
52
36
40
38
37
15
39
23
24
25
26
29
30
31
32
33
34
22
35
21
20
HM5264165FTT-A60
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
VDDQ
/CS
/RAS
/CAS
/WEN
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
BA
SDRAM 64M
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
U10
TP208
SDD [31: 0]
SDBA1 (2, 7)
SDBA0 (2, 7)
GND
SDCLK (2, 7)
SDCKE (2, 7)
DQMUU (2, 7)
DQMUM (2, 7)
TP288
TP230
SDA0
SDA1
SDA2
SDA3
SDA4
SDA5
SDA6
SDA7
SDA8
SDA9
SDA10
SDA11
(2) SDCAN0
(2, 7) SDRASN
(2, 7) SDCASN
(2, 7) SDWEN
SDD15
SDD14
SDD13
SDD12
SDD11
SDD10
SDD9
SDD8
SDD7
SDD6
SDD5
SDD4
SDD3
SDD2
SDD1
SDD0
0.1
C75
+3.3V
1
14
27
3
9
43
49
19
18
17
16
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
VSS
VSS
VSS
VSSQ
VSSQ
VSSQ
VSSQ
NC
NC(RFU)
CLK
CKE
DQML
DQMU
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
BA
28
41
54
6
12
46
52
36
40
38
37
15
39
23
24
25
26
29
30
31
32
33
34
22
35
21
20
HM5264165FTT-A60
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
VDDQ
/CS
/RAS
/CAS
/WEN
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
U11
SDRAM 64M
SDBA1 (2, 7)
SDBA0 (2, 7)
GND
SDCKE (2, 7)
DQMUU (2, 7)
DQMUM (2, 7)
TP229
TP231
SDA0
SDA1
SDA2
SDA3
SDA4
SDA5
SDA6
SDA7
SDA8
SDA9
SDA10
SDA11
GND
100
R25
100
R24
+3.3V
SDCLK (2, 7)
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-36
SDA11
SDA1
SDA3
SDA5
SDA7
SDA9
SDA12
SDA0
SDA2
SDA4
SDA6
SDA8
SDA10
GND
(2, 6) DQMLL
(2) SDCSN3
(2, 6) SDCKE
(2, 6) SDCLK
(2, 6) SDRASN
(2, 6) SDCASN
(2, 6) SDBA0
(2, 6) DQMUM
(2) IICSDA
(2) IICSCL
(2, 6) DQMLM
(2, 6) SDCKE
(2, 6) SDWEN
(2) SDCSN2
(2, 6) SDCLK
(2, 6) SDBA1
(2, 6) DQMUU
SDD3
SDD2
SDD1
ADD0
SDD7
SDD6
SDD5
ADD4
SDD19
SDD18
SDD17
ADD16
SDD23
SDD22
SDD21
ADD20
SDD11
SDD10
SDD9
ADD8
SDD15
SDD14
SDD13
ADD12
SDD27
SDD26
SDD25
SDD24
SDD31
SDD30
SDD29
SDD28
C76
47/6.3V
+3.3V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
GND
DQ0
DQ1
DQ2
DQ3
VCC
DQ4
DQ5
DQ6
DQ7
/DQMB0
GND
A0
A2
A4
A6
A8
A10/AP
BA1
A12
VCC
DU
RFU
RFU
CK0
GND
CKE0
/WE
/S0
/S2
VCC
NC
NC
NC
NC
GND
/DQMB2
DQ16
DQ17
DQ18
DQ19
VCC
DQ20
DQ21
DQ22
DQ23
GND
SDA
SCL
VCC
GND
DQ8
DQ9
DQ10
DQ11
VCC
DQ12
DQ13
DQ14
DQ15
/DQMB1
GND
A1
A3
A5
A7
A9
BA0
A11
A13
VCC
/RAS
/CAS
RFU
CK1
GND
CKE1
NC
S1
S3
VCC
NC
NC
NC
NC
GND
/DQMB3
DQ24
DQ25
DQ26
DQ27
VCC
DQ28
DQ29
DQ30
DQ31
GND
SA0
SA1
SA2
YS02
Optional
expanding
memory
(DIMM)
slot 1
SDA11
SDA1
SDA3
SDA5
SDA7
SDA9
SDA12
SDA0
SDA2
SDA4
SDA6
SDA8
SDA10
SDD3
SDD2
SDD1
ADD0
SDD7
SDD6
SDD5
ADD4
SDD19
SDD18
SDD17
ADD16
SDD23
SDD22
SDD21
ADD20
SDD11
SDD10
SDD9
ADD8
SDD15
SDD14
SDD13
ADD12
SDD27
SDD26
SDD25
SDD24
SDD31
SDD30
SDD29
SDD28
GND
(2, 6) DQMLL
(2) SDCSN5
(2, 6) SDCKE
(2, 6) SDCLK
(2, 6) SDRASN
(2, 6) SDCASN
(2, 6) SDBA0
(2, 6) DQMUM
(2) IICSDA
(2) IICSCL
(2, 6) DQMLM
(2, 6) SDCKE
(2, 6) SDWEN
(2) SDCSN4
(2, 6) SDCLK
(2, 6) SDBA1
(2, 6) DQMUU
+3.3V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
GND
DQ0
DQ1
DQ2
DQ3
VCC
DQ4
DQ5
DQ6
DQ7
/DQMB0
GND
A0
A2
A4
A6
A8
A10/AP
BA1
A12
VCC
DU
RFU
RFU
CK0
GND
CKE0
/WE
/S0
/S2
VCC
NC
NC
NC
NC
GND
/DQMB2
DQ16
DQ17
DQ18
DQ19
VCC
DQ20
DQ21
DQ22
DQ23
GND
SDA
SCL
VCC
GND
DQ8
DQ9
DQ10
DQ11
VCC
DQ12
DQ13
DQ14
DQ15
/DQMB1
GND
A1
A3
A5
A7
A9
BA0
A11
A13
VCC
/RAS
/CAS
RFU
CK1
GND
CKE1
NC
S1
S3
VCC
NC
NC
NC
NC
GND
/DQMB3
DQ24
DQ25
DQ26
DQ27
VCC
DQ28
DQ29
DQ30
DQ31
GND
SA0
SA1
SA2
YS03
Optional
expanding
memory
(DIMM)
slot 2
A-37
(3) CDET2B
(3) CDET2A
(3) CFWAITN2
+3.3V
(3) CFCSN1
(3) CFOEN2
RA35
10kx4
TP388
TP386
TP415
(3) CFRST2
(3) CFWEN2
TP413
(3) CFCSN2
TP403
TP245
LD8 TP255
LD9
LD10
TP253
LA20TP251
TP249
TP247
LD11
LD12
LD13
LD14
LD15
LD0
LD1
LD2
LA7
LA6
LA5
LA4
LA3
LA2
LA10
LA9
LA8
LA11
LD3
LD4
LD5
LD6
LD7
+3.3V
51
52
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
(2, 4) EXTBOEN
(3) CFOEN1
(3) CFCSN1
(3) CFCSN2
CONNECTOR CF-CARD
GND
D3
D4
D5
D6
D7
/CE1
A10
/OE
A9
A8
A7
VCC
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
WP
/CD2
/CD1
D11
D12
D13
D14
D15
/CE2
/VS1
/IORD
/IOWR
/WE
RDY//BSY
VCC
/CSEL
/VS2
RESET
/WAIT
/INPACK
/REG
BVD2
BVD1
D8
D9
D10
GND
YC06
C80
22/6.3V
(4, 5, 9) LA [22: 0]
2
4
6
8
1
3
5
7
TP400
TP401
TP402
LA4
LA3
LA2
LA20
LA11
LA10
LA9
LA8
LA7
LA6
LA5
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
1
15
2
4
6
10
12
14
19
1
2
3
4
5
6
7
8
9
GND
VCC
GND
D1
D2
D3
D4
D5
D6
D7
D8
20
10
18
17
16
15
14
13
12
11
VCC
GND
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
16
8
3
5
7
9
11
13
GND
GND
TP256
0.1
C87
CFA4
CFA3
CFA2
+3.3V
0.1
C86
CFA20
CFA11
CFA10
CFA9
CFA8
CFA7
CFA6
CFA5
+3.3V
0.1
CFD7
CFD6
CFD5
CFD4
CFD3
CFD2
CFD1
CFD0
SN74LV245A_01
18
17
16
15
14
13
12
11
C82
VCC
GND
D1
D2
D3
D4
D5
D6
D7
D8
+3.3V
20
10
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U13
SN74LV367A_01
/1OE
/2OE
1A1
1A2
1A3
1A4
2A1
2A2
U15
GND
0.1
CFD15
CFD14
CFD13
CFD12
CFD11
CFD10
CFD9
CFD8
SN74LV245A_01
18
17
16
15
14
13
12
11
C81
VCC
GND
D1
D2
D3
D4
D5
D6
D7
D8
20
10
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U12
SN74LV245A_01
G
DIR
A1
A2
A3
A4
A5
A6
A7
A8
U14
19
1
2
3
4
5
6
7
8
9
19
1
2
3
4
5
6
7
8
9
TP378
TP379
TP380
TP381
TP382
TP383
TP384
TP385
(3) CDET1B
(3) CDET1A
(3) CFWAITN1
TP419
TP420
TP416
TP417
8TP18
+3.3V
+3.3V
(3) CCFCSN1
(3) CFOEN1
CFD [15: 0]
CCFCSN1
CCFCSN2
CFA20
RA34
10kx4
TP387
CFA20
TP414
(3) CFRST1
CFA [11: 2]
TP404
(3) CFWEN1
(3) CFCSN2
0.1
0.1
GND
C84
C83
TP397
TP398
TP399
TP389
TP390
TP391
TP392
TP393
TP394
TP395
TP396
TP405
TP406
TP407
TP408
TP409
TP10
TP411
TP412
2
4
6
8
1
3
5
7
(4, 5) LD [15: 0]
TP244
TP252
CFD8 TP254
CFD9
CFD10
TP250
TP248
TP246
CFD11
CFD12
CFD13
CFD14
CFD15
CFD0
CFD1
CFD2
CFD3
CFD4
CFD5
CFD6
CFD7
CFD7
CFD6
CFD5
CFD4
CFD3
CFD2
CFD10
CFD9
CFD8
CFD11
+3.3V
51
52
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
C79
22/6.3V
CONNECTOR CF-CARD
GND
D3
D4
D5
D6
D7
/CE1
A10
/OE
A9
A8
A7
VCC
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
WP
/CD2
/CD1
D11
D12
D13
D14
D15
/CE2
/VS1
/IORD
/IOWR
/WE
RDY//BSY
VCC
/CSEL
/VS2
RESET
/WAIT
/INPACK
/REG
BVD2
BVD1
D8
D9
D10
GND
YC05
FS-1800/1800N | FS-3800/3800N
TP277
(3) SVCCLK
TP280
TP282
TP283
TP284
TP285
TP286
(3, 12) BD
(3) FSYNC
(3, 4, 5) WEN0
(3, 4) OEN0
(3, 5) CSN2
(1, 2, 4) CPUD31
(1, 2, 4) CPUD30
(1, 2, 4) CPUD29
(1, 2, 4) CPUD28
(1, 2, 4) CPUD27
(1, 2, 4) CPUD26
(1, 2, 4) CPUD25
(1, 2, 4) CPUD24
(4, 5, 8) LA3
4, 5, 8) LA2
+XLI3.3V
FS-1800/1800N | FS-3800/3800N
A-38
GND
0.1
C96
C97
0.1
C98
0.1
PM-2020i
LPVSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
LPVDD
VDD3
VDD3
VDD3
VDD3
VDD3
VDD3
VDD5
PVIDEO7
PVIDEO6
PVIDEO5
PVIDEO4
PVIDEO3
PVIDEO2
PVIDEO1
PVIDEO0
/LSYNC
/SRCCLK
VIDEO
EOP
52 PIN QFP
0.1
TEST
TEST
TEST
/RST
FT3
FT2
FT1
FT0
BD
FSYNC
CLK
/WR
/RD
/CS
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
PA1
PA0
U16
C95
+XLI3.3V
GND
17
16
15
21
51
50
46
43
33
14
49
41
40
12
37
30
29
28
27
26
25
22
39
38
TP600
Image Chip
23
48
47
35
34
20
9
8
24
45
32
31
18
6
5
19
52
1
2
3
4
7
10
11
R232
42
44
36
13
+XLI3.3V
GND
+5V
0.1
C92
0.047
C91
GND
C88
0.1
22/6.3V
CHIP
TANTAL
C94
TP560
22/6.3V
CHIP EL.
+ C180 +
TP551
R231
+XLI3.3V
TP261
TP262
TP263
TP264
TP265
TP266
TP267
TP268
TP552
TP276
TP275
TP269
TP270
TP279
TP550
56
56
VIN
GND
ON/OFF
LP2981-3.3_01
NC
VOUT
U28
1
2
3
5V - 3.3V REGULATOR
PVIDEO7 (3)
PVIDEO6 (3)
PVIDEO5 (3)
PVIDEO4 (3)
PVIDEO3 (3)
PVIDEO2 (3)
PVIDEO1 (3)
PVIDEO0 (3)
R27
R28
TP271
TP272
C93
+5V
SRCCLKN (3)
XLIDATA (3)
TP530
(3) P1284HD
(3) ACK
(3)BUSY
(3) PERROR
R260
(3) SELECT
(3) FAULT
(3) PDATA [ 8: 1]
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
0.1
PNSELIN
PNSTROBE
PNAUTOFD
PNINIT
PPDATA7
PPDATA8
PPDATA3
PPDATA4
PPDATA5
PPDATA6
PPDATA1
PPDATA2
PNACK
PBUSY
PPERROR
PSELECT
PNFAULT
0.1
SN74LVC161284
DIR
Y9
Y10
Y11
Y12
Y13
VCC_C
B1
B2
GND
B3
B4
B5
B6
GND
B7
B8
VCC_C
PLout
C14
C15
C16
C17
HLin
C103
HD
A9
A10
A11
A12
A13
VCC
A1
A2
GND
A3
A4
A5
A6
GND
A7
A8
VCC
PLin
A14
A15
A16
A17
HLout
IEEE 1284
Transceiver
C102
TP319
PDATA7
PDATA8
PDATA3
PDATA4
PDATA5
PDATA6
PDATA1
PDATA2
TP288
TP289
TP290
TP291
TP292
TP293
TP294
TP295
TP296
TP297
TP298
TP299
TP300
TP301
(3 SELECTIN
(3) STROBE
(12) AUTOFD
(3) INIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
TP317
P1284DIR (3)
UDZS5.6
DZ01
HZM6.8FA
DZA01
1
2
3
5
4
1
2
HZM6.8FA
DZA02
1
2
3
5
4
TP323
TP320
TP321
TP302
HZM6.8FA
DZA03
(11) FUSED5V
+5V
HZM6.8FA
DZA04
TP318
PNSTROBE
PPDATA1
PPDATA2
PPDATA3
PPDATA4
PPDATA5
PPDATA6
PPDATA7
PPDATA8
PNACK
PBUSY
PPERROR
PSELECT
PNAUTOFD
+5V
F01
PNSELIN
TP329
PNIINT
2.2kx4
U17
TP324
TP325
TP326
TP327
TP328
1
2
3
5
RA37
2
4
6
8
1
3
5
7
1
2
3
5
4
TP303
TP304
TP305
TP306
TP307
TP308
TP309
TP310
TP311
TP312
TP313
TP314
TP315
TP316
4
0
R32
+5V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
TP421
LP-U
LP-L
A-39
R34
+3.3V
nStrobe
Data1(LSB)
Data2
Data3
Data4
Data5
Data6
Data7
Data8(MSB)
nAck
Busy
PError
Select
nAutoFd
Not difined
Logic Gnd
Chassis Gnd
Periferal Logic High
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
Signal Ground
nInit
nFault
Not defined
Not defined
Not defined
nSelectin
CONNECTOR PERALLEL-B
LockPin(1)
LockPin(36)
STB
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
ACK
BUSY
PE
SEL
CAN
RMR
SG
FG
INIT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
ARARM
ASFON
FAULT
HSTI
EXPRM
PRDY
SELI
YC02
FS-1800/1800N | FS-3800/3800N
10k
C105
0.1
C107
0.1
(3) XRXD
(3) RSSEL
TP345
FS-1800/1800N | FS-3800/3800N
A-40
C110
+5V
CHIP EL.
100/16V
R39
0.1
GND
C112
GND
AIC1085-3.3CM
3 VCC OUT
1 GND
5V - 3.3V
REGULATOR
U20
1SS355
D03
2
+5V
TP343 TP344
SP01
SHORT PIN
1
2
3
TP341 TP342
GND
0.1
D04
+5V
1SS355
GND
C111
CHIP EL.
220/6.3V
GND
V+
V-
SHDN
/EN
R1IN
R2IN
R3IN
T1OUT
T2OUT
T3OUT
T4OUT
1
4
2
RO
GND
A
B
Z
Y
R42
+2.5V
R220
+5V
GND
R37
470
3
1
TP340
C106
0.1
TP336
R35
470
TP335
C115
0.1
0.20/2W
8
7
6
5
C108
0.1
MAX488CSA_02
VCC
GND
DI
0.20/2W
11
15
21
20
4
23
16
2
3
1
24
GND
U19E
MAX206CAG
+5V
VCC
C2+
C2-
C1+
C1-
R1OUT
R2OUT
R3OUT
T1IN
T2IN
T3IN
T4IN
U18
+3.3V
+3.3V
C109
13
14
10
12
(3) XCTS
(3) XDSR
SP01
SHORT PIN
7
8
9
5
22
17
(3) XTXD
(3) XDTR
(3) XRTS
TP330
TP331
TP332
TP333
TP334
7
6
18
19
C104
0.1
+5V
1SS355
D02
AIC1085CM
VCC OUT
GND
R36
100/0.5W
Chip R.
GND
DZ05
UDZ18B
1
5V - 2.5V
REGULATOR
U21
1
DZ02 2
UDZ18B
R44
1k
R43
1k
TP337
TP351
C116
0.1
GND
DZ03
TP347
(10) FUSED5V
GND
DZ06
UDZ18B
UDZ18B
C114
CHIP EL.
220/6.3V
+2.5V
SP01
SHORT PIN
4
5
6
DZ07
UDZ18B
TP338
DZ04
UDZ18B
R38
GND
BK1608HS241
TP339
FG
TXD
RXD/RDA
RTS
CTS
DSR
SG
DTR
RDB
SDA
SDB
Fused5V
YC03
GND
CONNECTOR 12PIN
1
2
3
4
5
6
7
8
9
10
11
12
TP511
0.1
C118
1A
1B
2A
2B
3A
3B
4A
4B
GND
1Y
4Y
3Y
2Y
1
2
3
4
5
1
2
3
4
5
YC08T
11
GND
TP512
TP515
TP514
TP513
WAUTOFD (3)
CONNCETOR 5PIN
B5B-PH-K-S
SN74LV08A_01
14 VCC
GND
1
2
4
5
9
10
12
13
TP510
10k
10k
(3) OPRDY2
(10) AUTOFD
+3.3V
(3) DBTXD
(3) DBRXD
(3) DBCLK
R41
R40
TP348
TP349
TP350
(3) FPDIR
(3) FPCLK
(3) FPDAT
(3) RSTIN
TP532
TP531
TP360
TP364
(3) VDOUTN
(3) VDOUTP
(3) SBSY
(3) VDFON
(3) SO
(3, 9) BD
(3) SI
(3) SDIR
(3) SCLK
(3) ENGIRN
TP352
TP500
TP501
TP502
2
4
6
8
RA39
TP356
TP503
TP504
TP505
100P 100P 100P 100P
GND
GND GND
GND GND
2
4
6
8
2.2kx4
RA39
2.2kx4
100P 100P
GND
GND
GND GND
GND GND
GND GND
GND GND
GND
C124 C125 C126 C127 C128 C129 C130 C131 C132 C133 C134
100P 100P
1
3
5
7
1
3
5
7
100P
1 56kx4
3
5
7
1 56kx4
3
5
7
RA41 2
4
6
8
RA42 2
4
6
8
1 56kx4
3
5
7
RA40 2
4
6
8
GND
CHIP EL.
100/16V
C117
0
(3) EXTIOR2
1
3
5
7
RA47
ACA3216MMM4S-600
2
4
6
8
RA45
ACA3216MMM4S-600
2
1
4
3
6
5
8
7
RA49
0
0
RA46
RA48
+5V
BK2125HM601
R52
+5V
0
R53
A-41
R54
+3.3V
GND
Lock Pin
Lock Pin
1
2
3
4
5
6
7
8
9
10
11
12
YC07
24V
5V
SCLK
SDI
SDO
READY
24VGND
PFSEL
OPSEL0
OPSEL1
OPSEL2
GND
CONNECTOR OPTION I/F_01
OP24V
OP5V
OPSCLK
OPSDI
OPSDO
OPREADY
OP24VGND
OPPFSEL
OPSEL0
OPSEL1
OPSEL2
R55
0
YC01
GND
GND
5V
5V
5V
SI
SDIR
SCLK
ESGIR
SBSY
VDFON
SO
GND
RESET
GND
PDOUT
GND
GND
GND
VDATAP
GND
VDATN
FPDIR
GND
FPPOWER
FPCLK
GND
FPDAT
SEL2
GND
SEL0
SEL1
GND(24)
PFSEL
SDO
READY
SCLK
SDI
24V
5V
CONNECTOR ENGINE40_01
G1
G2
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
BK2125HM601
R47
+3.3V
FS-1800/1800N | FS-3800/3800N
R2
PC2
R9
D3
R112
R111
R4
C8
CR1
L2
R1 C1
NR2
Q3
R16
R14
Q2
R22
PC4
3
R13
R12
R8
R7
R6
4
PC1
R3
R19
C14
D4
C12
R17
C9
PN1-1
D300 R41
Q5
R10 R11
C4
F2
L10
PKG2
PN1-2
HEATER 3
COM
HEATER 1
LIVE
CN2
SW1
R15
D11
C7
C16
R107
R106
R27
R105
R104
D1
R96
7
4
Vcc OUT
Z1
L4
C13
PC3
3
R34
R30
R40
D5
R109
R42
C17
Is
C28
PN1-7
Q1
Q12
T1
10
R69 R70
C44
D24
C39
R58
R57
1 PC5
R206
Q11
R59
R55 C201
PC4
PN2-2
C202
D214
R83
C200
Z2
D212
4
PC6
D213
R203
C36
+ +
C213
C35
L6
R90
R92
D22
R52
PN2-4 PN2-1
C48
D200 R84
D201
Q20
R87
1
PC3 C50
2
PN3-1
R202
+
C210
D211
R201
Q9
R204
R54
C38
D18
Q16
R62 R71
Q13 D25
R61
D21
1
RV1
2
C45
R68
R80
+
R88
C47
R53
C41
L5
D17
PN2-7
R208
3
C211
R205 C212
R200 D210
C53
R207
C301
C37
RC2
R86
R45
Q21
C31
D15
D14
R50
Q8
C30 C34
R49
Q10
FB11
RC3
PC5
4
D13
R110
FB13
FB12
12
13
C24 C25
R33
C19
C20
R37
R43
PN3-2
C23
R38
R31
C21
R32
R28
C26
D1
R5
D10
R29
C100 D9
D6
R24
R23
C18
TH1
C27
4 RT/CT
comp VFB GND
R18
1
2
5
8 Vref
D202
R20
C5
PN1-4
C3
C10
D2
C29
R47
D301
RC1
R44
CN1
C43
C6
PN3-3
R74
R75
R65
R73
R72
Q17
PN3-4
D19
R76
Q14
C46
R81 R56
R64
D23
R82
Q15
R79
R66
R85
C42
D20
Q18
R67
R63
C54
1
PC1
2
R78 R77
PN1-3
R101 R100
R103 R102
R300
L3
PN1-8
C2
R26
PN1-5
PN1-6
C300
L1
C51
NR1
C15
PN2-3
PN2-6
PN2-5
A-42
R51
FS-1800/1800N | FS-3800/3800N
PC2 3
R95
4 C52
R89
D26
PC6
1
PN3-7
C49
PN3-8
PN3-5
PN2-8
F1
R94
Q19
R93
1
2
3
4
5
6
7
8
YC302
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
18
20
21
22
23
24
YC301
*5V1
GND
THERM
EXITPAP*
FDDR
FUDR
+5V2
FDFUL
+5V2
FDUL
FDDR
FUDR
THERM
EXITPAP*
*5V1
GND
+24V2
SLEEP*
ZCROSS
HEAT*
+5V1
+5V1
+5V1
+5V1
GND
GND
GND
GND
+24V1
+24V1
+24V1
+24V1
PN3-6
R2
PC2
R9
D3
R112
R111
R4
C8
CR1
L2
R1 C1
NR2
Q3
R16
R14
Q2
R22
PC4
3
R13
R12
R8
R7
R6
4
PC1
R3
R19
C14
D4
C12
R17
C9
PN1-1
D300 R41
Q5
R10 R11
C4
F2
L10
SW1
PKG2
PN1-2
HEATER 3
COM
HEATER 1
LIVE
CN2
C10
R15
D11
C7
C16
R107
R106
7
4
Vcc OUT
D5
C13
PC3
3
R109
R42
Is
C28
Q1
Q12
T1
10
R69 R70
C44
D24
C39
Q11
R59
R55 C201
PC4
C202
D214
R83
C200
Z2
D212
4
PC6
D213
R203
C36
+ +
C213
C35
L6
R90
R92
D22
R52
PN2-4 PN2-1
C48
D200 R84
D201
Q20
R87
1
PC3 C50
2
PN3-1
R202
+
C210
D211
R201
Q9
R204
R54
C38
D18
Q16
R62 R71
Q13 D25
R61
D21
1
RV1
2
C45
R68
R80
+
R88
C47
R53
C41
L5
D17
PN2-7
R208
3
C211
R205 C212
R200 D210
C53
R207
C301
C37
RC2
D14
R50
Q8
R86
R45
PN2-2
C31
D15
Q21
R58
C30 C34
R206
R57
1 PC5
2
R49
Q10
FB11
RC3
PC5
4
D13
R110
FB13
FB12
12
13
C24 C25
R33
C19
C20
R37
R43
PN3-2
C23
R38
R31
C21
R32
R28
C26
D1
R5
D2
D10
PN1-7
C17
4 RT/CT
comp VFB GND
R18
1
2
5
Z1
L4
R34
R30
R40
R29
C100 D9
D6
R105
R27
R24
R23
C18
TH1
C27
R104
D1
R96
8 Vref
D202
R20
C5
PN1-4
C3
RC1
R44
CN1
C43
C6
PN3-3
R74
R75
R65
R73
R72
Q17
PN3-4
D19
R76
Q14
C46
R81 R56
R64
D23
R82
Q15
R79
R66
R85
C42
D20
Q18
R67
R63
C54
1
PC1
2
R78 R77
PN1-3
R101 R100
R103 R102
R300
L3
PN1-8
C2
R26
PN1-5
PN1-6
C300
L1
PN2-3
PN2-6
PN2-5
NR1
C15
C51
C29
R47
D301
R51
A-43
PC2 3
R95
4 C52
R89
D26
PC6
1
PN3-7
C49
PN3-8
PN3-5
PN2-8
F1
PN3-6
R94
Q19
R93
1
2
3
4
5
6
7
8
YC302
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
18
20
21
22
23
24
YC301
*5V1
GND
THERM
EXITPAP*
FDDR
FUDR
+5V2
FDFUL
+5V2
FDUL
FDDR
FUDR
THERM
EXITPAP*
*5V1
GND
+24V2
SLEEP*
ZCROSS
HEAT*
+5V1
+5V1
+5V1
+5V1
GND
GND
GND
GND
+24V1
+24V1
+24V1
+24V1
FS-1800/1800N | FS-3800/3800N
FS-1800/1800N | FS-3800/3800N
A-44
R41
56k
(2W)
D6
1N4005E
D8
1N4005E
L2
Z0069
FS1
250V
8A
D7
1N4005E
R42
56k
(2W)
L3
C5
2200p
AC250V
C50
10000p
AC250V
R11
120
1/2W
(FUSE)
C8
120F
400V
C10
0.001
630V
R7
56k
R9
12k
ZD2
HZS20
T1
ZD737
Primary circuit
PC2
PC123
R11
15
(FUSE)
C27
1000p
500V
or
1kV
BJ3
R26
8k
Secondary circuit
PC3
S21ME6
R13
2.4k
(1/4W), (1/2W)
VR2 R12
2k-5k 15k
C9
4700p
50V
R8
10k18k
R10
2.2
(FUSE)
Q2
2SC1213
2SC1207
PC1
PC123
R6
C8
470 0.01
(2W) 50V
R3
470k-1M
R2
470k-1M
TRC1
TM861S
ZD1
HZS15
RD15(16)ES
MTZJ15(16)
BJ2
ENC471D10A
(Option)
C23
0.1
AC250V
R4
22
(2W)
R5
4.7
(FUSE)
C7
Q1
220p 2SK2082
1kV
D10
ERA22-08
R16
220k
(1/2W)
BD1
D3SBA50
TH1
C2
C4
NTH13D8ROLA
4700p
0.1
8D-13
AC250V AC250V
C1
Option 4700p
AC250V
D9
1N4005E
Z04C8
L1
C3
R1
470k 0.22
(1/4W) AC250V
NR1
ENC471D10A
NV471D14
FS2
250V/4A
C42
0.01
250V
SW1-2
CN2
S203-VH
CN1 SW1-1
INLET
C12
470
50V
Q7
DTC114
R27
180k
R35
D5
33
1SS244
(FUSE) HSS81
C14
2200
10V
D2
YG802C04
R44
6.8k
(1/2W)
D1
YG902C2
C11
1000p
500V or 1kV
C16
0.1
50V
R21
47k
IC1
LS431, PC1093
HA1743PA
TL431, KIA431
R46
82
C17
1
50V
R36
33
R19
2.2k
VR1
1k
R18
2.7k
SRC1
TF541S
TF321S
R40
1k
L5
Z400
Q8
DTC114
ZD3
HZS36
RD5.6(6.2)ES
MTZJ5.6(6.2)
ZD7
HZS27
-24
Q4
DTA114
R15
330 C25
0.1
50V
R32
180
(1/2W)
R30
10k
R14
680-1.2k
C15
2200
10V
PC1
PC123
R29
2.2k
Q6
2SC1213
Q5
2SC1213
C13
470
50V
R31
47k
R28
10k
Q3
2SJ477
C40
2200
10V
FS3
6.3A
THERM
FDDR
GND
21
22
24
+24V1
+24V1
+24V1
+24V1
20
23
GND
GND
19
GND
17
18
+5V1
+5V1
15
16
+5V1
+5V1
13
ZCROSS
HEAT
11
12
14
+24V2
SLEEP
9
10
+5V1
GND
7
8
THERM
EXITPAP*
5
6
FUDR
4
+24V2
FDPFUL
2
YC901
MSA-9136S-24L
+24V2
FDPFUL*
FUDR
FDDR
EXITPAP*
YC902
S88-PH
1 +5V1
2 GND
Appendix B
S t a t u s
P a g e
Appendix B Contents
Status page ............................................................................................................................................. B-3
Printing the service status page .......................................................................................................... B-3
Service information on the status page ............................................................................................... B-4
Details of service information .............................................................................................................. B-4
Status page
The printer can print two different types of the status pagethe user (normal) status page and the
service status page. This section exclusively describes information obtainable with the service status
page. For information on the user (normal) status page, refer to the printers Users Manual.
Information on the service page include various settings for the printer, service statistics, etc. To
print a service status page, proceed as follows:
Printing the service status page
To print a service status page, using the MENU key. Or, have a PC running MS-DOS and proceed
as follows:
1. Connect the printer to the PC via the parallel interface.
2. Ensure that the printer is ready to print.
3. At the DOS prompt, type:
echo !R! STAT 1; EXIT; >lpt1:
The service status page is printed. (If you omit 1, a user status page is printed.)
FS-1800/1800N | FS-3800/3800N
B-3
Released:
30/Aug/2000
Service information
[0104/0330][C1*][12][01/01]
Total page
/t/P00/S00/F00/N00/D10:DM0301.DAN/RS2/DK-60/6C/01/[0003-0003]/BF-AD/AF.H/
/0096/0026/1061/0811/ 0/ 0/ 0/ 0/ 0/ 0/ 0/
/AAADCFE/AAADCFE/AAADCFE/AAADCFE/AAADCFE/AAADCFE/AAADCFE/AAADCFE/
/20A11080/1020B200/20001080/81000000/00000000/10101010/10101010/
SPD1:0203040508090A0B0C0D0F101112131415161718191A1B1C1D1E1F202122235E
SPD2:0203040508090A0B0C0D0F101112131415161718191A1B1C1D1E1F202122235E
/8088808880808000/8088808880808000/8088808880808000/8088808880808000/
DN:SPL9200007 SN:SPL9200010
Service information
FS-1800/1800N | FS-3800/3800N
B-4
9690
0/20/25/60
Service information
[0104/0330][C1][12*][01/01]
Total page
2 3
9690
/t/P00/S00/F00/N00/D10:DM0301.DAN/RS2/DK-60/6C/01/[0003-0003]/BF-AD/AF.H/0/20/25/60
67 8 9 0
/0096/0026/1061/0811/
0/
0/
# $%
0/
0/
0/
0/
0/
&
* ()
/AAADCFE/
/20A11080/1020B200/20001080/81000000/00000000/10101010/10101010/
SPD1:0203040508090A0B0C0D0F101112131415161718191A1B1C1D1E1F202122235E
SPD2:0203040508090A0B0C0D0F101112131415161718191A1B1C1D1E1F202122235E
/8088808880808000/8088808880808000/8088808880808000/8088808880808000
DN:SPL9200007 SN:SPL9200010
Example
1 [0104/0330]
Meaning
Description
B-5
Example
8 /S00
9 /F00
0 /N00
! /D10:DM0301.DAN
@ /RS2
# /DK-60
$ /6C
% /01
^ /[0003-0003]
& /BF-AD
* /AF.H
Meaning
Serial interface error
Description
FS-1800/1800N | FS-3800/3800N
B-6
Example
( /0
) /20
/25
/60
/0096/0026/1061
/0811
/
/
/
0/
0/
0
0/
0/
0
0
/AAADCFE/AAADCFE
/AAADCFE/AAADCFE
/AAADCFE/AAADCFE
/AAADCFE/AAADCFE
/20A11080/1020B200
/20001080/81000000
/00000000/10101010
/10101010
SPD1:02030405...
SPD2:02030405...
/8088808880808000
/....
DN:SPL92000007
SN:SPL92000010
Meaning
Description
Operator panel message PMSG command settings shown by
language
decimal.
Toner capacity
Number of pages shown by decimal
( 1000 pages)
The present temperature
0 to 100 C, When if - shows, the
temperature/humidity sensor is
abnormal.
The present humidity
55 to 90 %, step by 5%
Printing area
/Top margin/Left margin/Page
length/Page width/, Inches+ 1/ 100
inches (FRPO L1/L2)
in 1/600 inch
Left margin offset for paper
source (MP tray/Printers
cassette/Top paper feeder/
Middle feeder/Bottom feeder/
Envelope feeder/Duplexer)
Life counter for each option Paper feeder4/Duplexer/Bulk paper
units
feeder/Bulk paper stacker/Sorter
SPD (slot1)
SPD (slot2)
Engine Parameter information Hexadecimal, 32 bytes (64 digits)
Serial number for the drum
Serial number for the printer
FS-1800/1800N | FS-3800/3800N
B-7
Appendix C
Appendix C Contents
Parallel interface .................................................................................................................................... C-3
Selecting the parallel interface mode .................................................................................................. C-3
Parallel interface pin assignment ........................................................................................................ C-4
Parallel interface signals ..................................................................................................................... C-5
Serial interface ....................................................................................................................................... C-6
RS-232C interface voltage levels ........................................................................................................ C-6
Connector configurations .................................................................................................................... C-6
Protocol ........................................................................................................................................... C-7
RS-232C - For computers with a DB-9 connector .......................................................................... C-7
RS-232C - For computers with a DB-25 connector ........................................................................ C-7
Parallel interface
The printer uses a bidirectional parallel interface for high-speed data transmission for the host
computer. This interface includes the buffers which are compatible with the IEEE 1284 standards.
The parallel interface provides support for the ECP and nibble modes in this standards. The parallel
interface mode can be changed by commanding Prescribe commands on a PC.
Selecting the parallel interface mode
To change the parallel interface mode, a PC running MS-DOS is needed. Connect the printer to the
PC via the parallel interface. Then, at the DOS prompt, type a FRPO O0 (the letter O and the
number zero) command as follows depending on the desired parallel mode:
FS-1800/N | FS-3800/N
C-3
FS-1800/N | FS-3800/N
C-4
Meaning
FS-1800/N | FS-3800/N
C-5
Serial interface
The printer is equipped with a serial interface connector. The device responsible for controlling the
serial interface is integrated in the gate array in the controller system. The serial interface supports
protocol of RS-232C. A 25-pin D-sub connector is used for the serial interface.
RS-232C interface voltage levels
The voltage levels of the RS-232C signals conform to EIA RS-232C specifications. FALSE is from
3 volts to 15 volts. TRUE is from -3 volts to -15 volts. Voltages between -3 volts and 3 volts are
undefined.
Connector configurations
The printer uses a DB-25 connector for the serial interface. Depending on the computer configurations
for serial interface, use either of the appropriate configurations.
Signal
FG (Pin 1)
TxD (Pin 2)
RxD (Pin 3)
RTS (Pin 4)
CTS (Pin 5)
DSR (Pin 6)
SG (Pin 7)
+5V (Pin 12)
DTR (Pin 20)
Meaning
This pin is connected directly to the printer frame.
This output carries asynchronous data sent by the printer to the computer.
It is used mainly in handshaking protocols.
This input carries serial asynchronous data sent by the computer to the
printer.
This output is always held high (above 3 V).
Unused.
Unused.
All signals can transmit between the printer and the host computer to send
each signals with a signal ground.
Power supply for barcode reader. (Maximum 500 mA)
This output is used as a buffer nearly-full handshake line. It is held high
(above 3 V) when the buffer can accept more data.
FS-1800/N | FS-3800/N
C-6
Protocol
The serial interface supports the full baud rate of: 1200, 2400, 4800, 9600, and 19200, 38400,
57600 and 115.2 k (bps). For adjusting serial interface parameters including baud rate, parity, etc.,
refer to printers Users Manual.
RS-232C - For computers with a DB-9 connector
Printer
Serial interface
connector (DB-25)
Computer
serial port (DB-9)
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
2
3
4
5
6
7
)
TXD
RXD
RTS
CTS
DSR
SG
DTR
Computer
serial port (DB-25)
GND
TXD
RXD
RTS
CTS
DSR
GND
DTR
1
2
3
4
5
6
7
)
1
2
3
4
5
6
7
)
FG
TXD
RXD
RTS
CTS
DSR
SG
DTR
FS-1800/N | FS-3800/N
C-7