Professional Documents
Culture Documents
XR04.48-XR08.48 Rectifier Modules - Power One - Pitesco
XR04.48-XR08.48 Rectifier Modules - Power One - Pitesco
Features
Description
The Power-One Advance Controller Card (ACC) is a pluggable microprocessor controller that
provides monitoring and control for a broad range of Power-One DC Power Systems. The ACC
monitors all system parameters including: DC voltage, rectifier current, rectifier temperature, system
capacity, battery parameters, and circuit breaker status.
Alarm and warning notifications are indicated by front panel LEDs, and through potential free alarm
contacts that allow remote signaling. External monitoring of alarms is accomplished through a USB or
RS232 port using PC-based PowCom software. The ACC has an Ethernet port allowing control
over a TCP/IP network and web based support. Alarms can be mapped via SNMP traps to customer
OSS platforms such as HP Openview
To meet individual site requirements, the ACC contains a Programmable Logic Unit that can be used
to monitor and control specified requirements. This allows individual alarm routing and logic
operations to be set as actions, alarms to be triggered, and outputs to be activated based on internal
and external signal monitoring, comparing, and processing.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Voltage
18-60 VDC
Current
<200 mA
Interface
Display
Internal
Communication
External
Communication
Indications
Signal Input
Signal Outputs
Software
Alarms
Alarm Contacts
Alarms
Dimensions
(WxHxD)
Weight
Operating Temp.
-40 to +70 C
Storage Temp.
-40 to +85 C
Safety
EMC
Environment
Battery Management
Battery
Disconnection
Boost Charging
Battery Tests
Enhanced Battery
Monitoring
Site Logs
Symmetry
Measurement
Temperature
Compensation
Charging
Load Shedding
(PLD)
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Ethernet interface
Simple installation
Description
Aspiro DC power systems offer a range of solutions for diverse applications such as broadband access, cable
head ends, micro/pico BTS Cells, Enterprise, E911, and GSM-R. Aspiro uses highly-efficient, dense, and
reliable XR04.48 & XR08.48 rectifier modules and is highly-adaptable to provide a complete solution for
today's global applications. Its system management is accomplished via a pluggable PCC system controller,
complete with remote accessing functionality with an Ethernet, web server, and SNMP interface.
Highly-flexible distribution options offer the optimum 1U or 2U shelf solution for space-critical applications. In
addition, installation within compact environments is made simple and includes reduced-depth distribution
shelves catering for rear or side cable connection.
Page 1 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
Model
Voltage
Power
(max)
Current
(max)
XR04.48
48 VDC
420 W
9.1 A
XR08.48
48 VDC
837 W
18.2 A
Hot-pluggable unit
Temperature compensation
Page 2 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Additional Features
AC Connection Rear or side screw terminals connection for simple field installation
19, 23 or ETSI mounting available
Flexible Connection Rear or side connection of load circuits and ancillary signals
Page 3 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model
Options
1U Combi-Shelf
2U Power System
2U Power System
Output Power
(max. per system)
1.6 kW
2.4 kW
3.2 kW
Rectifier Modules
(max. per system)
2x 400 W Rectifier
or
2x 800 W Rectifier
3x 400 W Rectifier
or
3x 800 W Rectifier
4x 400 W Rectifier
or
4x 800 W Rectifier
Single Phase
or
3-Phase
Single Phase
or
3-Phase
Output
Input
Single Phase
AC Input Connections
(230 VAC)
Distribution
Battery Fuse (Qty)
15
N/A
10
10
Battery
Low Voltage Battery
Disconnect (LVBD)
Temperature
Compensation
Battery Symmetry
Connections
Yes
Yes
1
Dimensions
W x H x D (mm)
Mounting
19 / ETSI / MID-MOUNT
19 / ETSI / MID-MOUNT
19 / ETSI / MID-MOUNT
Rear
Rear
Rear
Yes
Yes
Mechanical
Cable Entry
Options
Partial Load
Disconnect (PLD)
N/A
N/A
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 4 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
The Power-One CMP 3.48, for use in the Galero Series of power systems in our convection cooled
rectifier series, provides advanced resonance switch mode technology (softswitching). An onboard
microcontroller and an RS 485 data bus provide monitoring of basic functions, status, and identification
information to the system controller (GMC).
The CMP 3.48 rectifier module is optimized for telecom applications and is designed to work in numerous
subrack/shelf configurations incorporating the GMC controller and varying distribution options.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Model
CMP 3.48
Current (max.)
Soft Start
Harmonics
EN 61000-3-2
(Power factor > 0.98
typical)
EN 61000-4-5
Input Voltage
Surge
Immunity
Fuse
T 3.15A
Connection
DIN 41612F
EMC
Output
Model
CMP 3.48
Output
Voltage
45-56 VDC
Power (max.)
364 W @ 56 VDC
354 W @ 54.5 VDC
6.5 A
Current (max.)
Efficiency
(at
55-100% load)
>91%
Tolerance
Transient
Response
Load Sharing
Ripple
Psophometric
Connection
EMC
Mechanical
Dimensions
(WxHxD)
43 x 120.8 x 264.5 mm
(1.7 x 4.75 x 10.4 in.)
Weight
Cooling
Natural convection
Insulation
Enclosure
Green LED
Red LED
EN 61000-6-2,
EN 61000-6-4
Power ON
High output voltage/
shut down, Low
voltage/ module
failure
Audible
Noise
<35 dBA
Operating
Temperature
Storage
Temperature
-40 to +85 C
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
ETS 300 019-2-1
Storage:
Environment
ETS 300 019-2-2
Transport:
ETS 300 019-2-3
Operation:
GR 63 Core Zone
Earthquake:
4
*Average performance for a single module.
Radiated EMC
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Description
The Power-One FMP16.48 rectifier provides
extremely reliable DC power in the highest
possible density.
This rectifier module
incorporates the latest in power monitoring
solutions using an internal microprocessor that
gives up-to-the-second updates to the system
controller and adjacent rectifiers. This
guarantees tightly controlled load sharing
among rectifiers and provides status and
identification information to the controller.
At only four rack units high, these compact
rectifiers provide up to 1600 watts and allow up
to 10 rectifier modules in a 23-inch subrack or
eight modules in a 19-inch subrack. Designed
with diversity in mind, the FMP16.48 rectifier is
able to operate in a complete range of indoor
and outdoor applications.
Features
Page 1 of 2
Thermal protection
Hot-swappable
No adjustments required
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Mechanical
Model
FMP16.48
Input Voltage
Current (max.)
<10 A
Soft Start
<13A /1ms
Harmonics
EN 61000-3-2
(Power factor > 0.98 typical)
Dimensions
(WxHxD)
51 x 177 x 280 mm
(2.0 x 6.97 x 11.02 in)
Weight
Cooling
Insulation
Enclosure
IP20
Mounting
Surge Immunity
EN 61000-4-5
Fuse
Connection
FCI 51939-066
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Safety
EN 60950-1
UL 60950-1, IEC60950-1,
and CSA C22.2 No. 60950-1
Protection
Alarms
Indications
Green LED
Power ON
Yellow LED
Red LED
Output
Model
FMP16.48
Output Voltage
45-57 VDC
Power (max.)
Current (max.)
32 A
Efficiency
(at 40-90% load)
Tolerance
Vout 1.0%
Transient
Response
5% at load variation
10-90% or 90-10%
recovery time 50 ms
Load Sharing
Ripple
Psophometric
Audible
Noise
<60dBA
Connection
FCI 51939-066
EMC
EN 61000-6-2, EN 61000-6-4
Operating
Temperature
Storage
Temperature
-60 to +85 C
Radiated EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Environment
Storage:
Transport:
Operation:
Earthquake:
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Description
The FMP18.48 rectifier incorporates resonancesoft-switching technology to reduce component
stresses, providing increased system reliability
and a best-in-class efficiency. With a wide-input
operating voltage range of 84-300 VAC and linear
derating of output power with input voltage, the
FMP18.48 maximizes power availability in
demanding utility power environments.
These compact rectifiers support up to eight 4U
high rectifier units delivering up to 9 kW of power
while the 23 shelf can deliver up to 18 kW of
power. A wide variety of distribution options are
available to provide the maximum system
flexibility for a wide range of communications
applications that demand efficiency, reliability,
and flexibility including wireless base stations,
remote switches, and broadband access.
Features
Page 1 of 2
Thermal protection
Hot-swappable
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Mechanical
Model
FMP 18.48
Input Voltage
Current (max.)
<11.5 A
Soft Start
<13A /1ms
Harmonics
EN 61000-3-2
(Power factor > 0.98 typical)
Dimensions
(WxHxD)
51 x 177 x 280 mm
(2.0 x 6.97 x 11.02 in)
Weight
Cooling
Insulation
Enclosure
IP20
Mounting
Surge Immunity
EN 61000-4-5
Fuse
Connection
FCI 51939-066
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Safety
EN 60950-1
UL 60950-1 and IEC 60950-1
CSA C22.2 No. 60950-1
Model
FMP 18.48
Protection
Output Voltage
45-58 VDC
Alarms
Indications
Green LED
Power ON
Yellow LED
Fan pre-warning /
thermal derating.
Com. failure (flashing)
Red LED
Output
Output Power
Characterisitc
1800W
(50-56 VDC)
1050W
750W
85V
130V
185V
300V
Po max = 1800
Linear derate: 1800 to 1050 W
Current (max.)
38 A
Efficiency
(at 40-90% load)
Tolerance
Vout 1.0%
Transient
Response
5% at load variation
10-90% or 90-10%
recovery time 50 ms
Audible
Noise
<60 dBA
Load Sharing
Ripple
Operating
Temperature
Psophometric
Storage
Temperature
-60 to +85 C
Connection
FCI 51939-066
Radiated EMC
EMC
EN 61000-6-2, EN 61000-6-4
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Environment
Storage:
Transport:
Operation:
Earthquake:
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
The FMP25.48 rectifier incorporates resonant technology to reduce component stresses, providing
increased system reliability and a best-in-class efficiency. The rectifier features a wide input operating
voltage range to maximize power availability within demanding utility power environments.
These compact rectifiers support up to 12.5kW in a 1RU 23 shelf. A wide variety of distribution options
are available to provide the maximum system flexibility for a wide range of communications applications
that demand efficiency, reliability, and flexibility including wireless base stations, remote switches, and
broadband access.
Typical Configuration
25kW in 23, 6RU with Controller
Load & Battery Distribution
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Mechanical Data
Model
FMP25.48
Input voltage
Nominal: 100-240V AC
Dimensions
Weight
Cooling
Permitted variation:
85-300V AC
Insulation
Derated Output:
85-180V AC
Current (max.)
<18A
Soft Start
Harmonics
EN 61000-3-2
Power Factor > 0.98 Typical
Surge immunity
EN61000-4-5
Fuse
EMC
EN61000-6-2, EN6100-6-3
FCC Part 15 Class B
Enclosure
Mounting
Output voltage
46-57 VDC
Po Max = 2500W
Efficiency
92.5%
Tolerance
Vout 1.0%
Transient response
UL 60950-1/ CAN/CSA-C22.2
No. 60950-1-03, 1st Ed.
EN60950-1: 2006
IEC 60950-1:2001
Output
Output power
(50-56 VDC)
Protection
Alarms
Indicators
Load sharing
Ripple
Psophometric
EMC
EN 61000-6-2, EN 61000-6-4
<60 dBA
Operating
temperature
Storage temperature
-60 to +85C
Environment
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
The Power-One FMP 32.48 rectifier provides extremely reliable DC power in the highest possible density.
The module incorporates the latest in power monitoring solutions using an internal microprocessor that
gives up-to-the-second updates to the system controller and adjacent rectifiers. This guarantees tightly
controlled load sharing among rectifiers and provides status and identification information to the
controller.
At only four rack units high, these compact rectifiers provide up to 3200 watts and allow up to five rectifier
modules in a 23-inch subrack or four modules in a 19-inch subrack. Designed with diversity in mind, the
FMP 32.48 rectifier is able to operate in a complete range of indoor and outdoor applications.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Model
FMP32.48
Mechanical
Dimensions
(WxHxD)
Weight
Cooling
Current (max.)
Soft Start
<2 x 13 A/1 ms
Harmonics
EN 61000-3-2
(Power factor > 0.98 typical)
Enclosure
Surge Immunity
EN 61000-4-5
Mounting
Fuse
Connection
FCI 51939-066
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Output
Model
FMP 32.48
Output Voltage
45-57 VDC
Power (max.)
Input Voltage
Current (max.)
Insulation
Efficiency
(at 40-90% load)
Tolerance
Transient
Response
Load Sharing
Ripple
Yellow LED
Psophometric
Connection
Red LED
EMC
EN 61000-6-2, EN 61000-6-4
Current limit/
thermal
protection. Com.
failure (flashing)
Module failure/
high output
voltage/ shutdown
Audible Noise
<60 dBA
Operating
Temperature
Storage
Temperature
-60 to +85 C
Radiated EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Environment
Storage:
Transport:
Operation:
Earthquake:
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Shelf Systems
Input
Model
Galero 1750
Galero 2450
Input
230/400V AC 3-phase
205-240V AC 1-phase
Site configurable
230/400V AC 3-phase
205-240V AC 1-phase
Site configurable
Single input
Single input
Inputs
(max.)
Output
Rectifier Modules
(max.)
Battery Outputs
Load Outputs
10
Yes
48V DC Version
Yes
Features
GMC
GMC
Yes
Yes
Yes
Yes
Supervision
Battery
Battery Symmetry Inputs
(max.)
Mechanical
Dimensions (WxHxD)
483x125x280mm
483x125x280mm
Mounting
19in., ETSI
19in., ETSI
Cable Entry
AC - Rear
DC and signals -Top
AC - Rear
DC and signals -Top
Yes
Yes
Battery Symmetry
Measurement
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
Options
Description
Features
High reliability
Simple installation and operation
Natural convection cooling - no fans
RS232 interface for remote operation
Form C dry alarm contacts
Intelligent battery management
Pluggable controller and DC distribution
modules
Optional Ethernet (SNMP compatible) interface
module
International standards compliance
www.power-one.com
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Configurations
System Components
Rectifier Module
The Galero Shelf System utilizes plug-in rectifier
modules based on a soft-switching approach.
Features include 2xLED for rectifier status indication,
thermal protection with de-rating and input overvoltage disconnection with automatic reset.
Galero 1750 System
All-in-one 125 mm high shelf system for integration into standard
19 or ETSI cabinets.
Complete subrack for five rectifier modules, supervision module
and DC distribution with battery breakers (1-2) and load breakers
(9-10).
Rectifier Features
Model
Voltage
Power
(max.)
Current
(max.)
CMP 3.48
48V DC
364W
6.5A
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Configurations
System Components
Rectifier Module
The Galero Shelf System utilizes plug-in rectifier
modules based on a soft-switching approach.
Features include 2xLED for rectifier status indication,
thermal protection with de-rating and input overvoltage disconnection with automatic reset.
Galero 1750 System
All-in-one 125 mm high shelf system for integration into standard
19 or ETSI cabinets.
Complete subrack for five rectifier modules, supervision module
and DC distribution with battery breakers (1-2) and load breakers
(9-10).
Rectifier Features
Model
Voltage
Power
(max.)
Current
(max.)
CMP 3.48
48V DC
364W
6.5A
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Shelf Systems
Input
Model
Galero 1750
Galero 2450
Input
230/400V AC 3-phase
205-240V AC 1-phase
Site configurable
230/400V AC 3-phase
205-240V AC 1-phase
Site configurable
Single input
Single input
Inputs
(max.)
Output
Rectifier Modules
(max.)
Battery Outputs
Load Outputs
10
Yes
48V DC Version
Yes
Features
GMC
GMC
Yes
Yes
Yes
Yes
Supervision
Battery
Battery Symmetry Inputs
(max.)
Mechanical
Dimensions (WxHxD)
483x125x280mm
483x125x280mm
Mounting
19in., ETSI
19in., ETSI
Cable Entry
AC - Rear
DC and signals -Top
AC - Rear
DC and signals -Top
Yes
Yes
Battery Symmetry
Measurement
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
Options
Description
Features
High reliability
Simple installation and operation
Natural convection cooling - no fans
RS232 interface for remote operation
Form C dry alarm contacts
Intelligent battery management
Pluggable controller and DC distribution
modules
Optional Ethernet (SNMP compatible) interface
module
International standards compliance
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
www.power-one.com
Features
User controls and interfaces:
compensation factor
Password-controlled environment
alarm contacts
Capacity testing
Low-voltage disconnect
Description
The Galero Microprocessor Controller (GMC) from Power-One provides comprehensive monitoring
and control of the Galero Power System. This digital controller monitors total system conditions
including DC voltage, rectifier current, rectifier temperature, system capacity, battery parameters, and
circuit breaker status.
The GMC enables data storage of system configuration information such as battery type, installation
date, and system commission date. Visual notification of alarm and warning conditions are indicated
by front panel LEDs, while descriptions of the alarms are provided through RS232 communication
using PC-based PowCom software package.
To meet individual site requirements, the GMC contains a Programmable Logic Unit that can be
programmed to monitor and control specified requirements. This allows actions to be set, alarms to be
triggered, and outputs to be activated based on internal and external signal monitoring, comparing,
and processing.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Voltage
N/A
Current
<200mA at 48V
Interface
Display
Internal Communication
External Communication
Indications
Controls
Signal Inputs (via alarm
interface)
N/A
RS485 data bus
RS232 Serial interface for
remote control from a PC with
PowCom software. TCP/IP or
SNMP available by using the
optional plug-in Ethernet
interface (PNI card)
Green LED - Power ON
Yellow LED - System Warning
Red LED System alarm
N/A
2 battery symmetry (12V
increments)
1 battery temperature sensor
3 analogue inputs for general
use
2 digital inputs for general use
Software
Language
N/A
Alarms
Alarm History
Alarm Contacts
Alarms
Dimensions
(WxHxD)
60 x 125 x 250mm
(2.4 x 4.9 x 9.8in.)
Weight
0.5kg (1.1lbs.)
Operating
Temperature
-25 to +55C
Environment
Storage:
Transport:
Operation:
Battery Management
Battery
Disconnection
Boost Charging
Battery Test
Symmetry
Measurement
Temperature
Compensation
Charging
PLD
N/A
Enhanced Battery
Monitoring
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Connected State of the art system controller with selfguided operation. SNMP and web compatible.
Intelligent
Guardian modular DC cabinet systems are designed to meet rigid telecom applications with very high
reliability and flexibility for future expansion.
Rectifier and battery combination cabinets are configurable to allow 12.5kW or 25kW rectifier
capacity together with DC distribution, controller and battery backup in a single footprint.
Options include battery and load disconnect, AC surge protection and various DC and AC
distributions.
Ideal for radio base stations, broadband nodes and core sites.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Technical Specification
600 x 600 x 1400/1800/2000mm (WxDxH)
Mechanical
Dimensions
Output
Voltage
-48VDC
Maximum Power
12.5kW / 25kW
Output Current
250 / 500A
Efficiency
92.50%
Rectifier types
FMP25.48G
Battery Breakers
DC Distribution
AC Input
Load Breakers
Battery Capacity
Voltage
1 or 2 x 230VAC 3 phase TN ()
1 or 2 x 400VAC 3 phase IT (Y)
Frequency
47-63Hz
Input Current
Power Factor
0.97
Surge Protection
Optional
Controller
ACC or PCC
Alarm relays
Local Interface
Remote interface
Visual Indication
Battery Management
Connections
Compliance
Symmetry Inputs
6 or 12*
Programmable LVD
1 x 300A or 500A
Programmable PLD
Battery Connections
AC connection
EMC
EN 300 386
EN 61000-6-3 (Emission)
EN 61000-6-2 (Immunity)
Environmental
Safety
IEC 60950
Operating Temperature
Storage Temperature
-40C to +85C
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
iBreaker Series
iB-PDU, Power Distribution Unit Data Sheet
Features
Applications
Telecom
Dimensions: 19 x 2U x 121mm,
(482.6 x 88 x 121mm)
Easy to replace
CE branded
Description
Based on Power-Ones revolutionary iBreaker, the modular iB-PDU is a configurable distribution unit
19x2U. The standard configuration distributes two input A+B sources -36Vdc / -60Vdc to 10 users. The
electronic circuit breaker assures no bus voltage drop, remote controllability, durability, reliability and a
faster response to short-circuit versus electromagnetic breakers.
The iBreaker device measures current, voltage, and energy consumption; then transmits the information via
serial link for precise system monitoring. It allows control of tripping conditions and implements low voltage
disconnection functionality for load shedding strategies to preserve critical loads. The iBreaker software
provides adjustable configurations that maximize system flexibility. Custom configurations are available.
Description
10 iBs in a 2U x 19 rack; in and out rear connectors
Page 1 of 3
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
iBreaker Series
iB-PDU, Power Distribution Unit Data Sheet
Technical Specifications
iBreaker-PDU Characteristics
General Characteristics
Input Voltage
Dimensions (WxHxD)
19 x 3.46 x 4.76 in
(482.6 x 88 x 121 mm)
Weight
Operating Temperature
-5 C to +55 C
20,000 operations
MTBF
1,000,000 hours
Cooling
Natural convection
EMC, CE Marked
Front Panel
Rear Panel
No. of Electronic
switches
10
Power source
/breaking capacity
5 kA
10A
10A
17A x 10 ms
< 0.1A
0.15V
Short-circuit sense
time
300 s (followed by 10
ms pre-programmed
current limit interval
Protection
Page 2 of 3
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
iBreaker Series
iB-PDU, Power Distribution Unit Data Sheet
Mechanical Drawings
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 3 of 3
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Telecom
Applications
Description
iBreaker Series Electronic Limiting, Interrupting and Monitoring Device
Power-Ones revolutionary iBreaker is a totally new product that increases performance and facilitates the design
of telecom 48V power systems. The iBreaker outperforms regular electromechanical interrupting devices by
delivering a higher level of reliability, consistency and durability in the field. The load is disconnected in a clean
way within 200 microseconds avoiding transients on the DC input bus. The iBreaker device measures current,
voltage and energy consumption then transmits the information via serial link for precise system monitoring. It
allows control of tripping conditions and implements low-voltage-disconnect functionality for load shedding
strategies to preserve critical loads. The iBreaker software provides adjustable configurations that maximize
system flexibility.
Model Selection
Model
Accessory
Model
Description
iB-48V-5A
iB-CTR
iB-48V-10A
10
iB-BS
iB-48V-20A
20
iB-48V-30A
30
iB-48V-40A
40
iB-WI
iB-48V-50A
50
iB-48V-60A
60
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Display
Isolation
Operating Temperature
-5 C to 55 C; convection
cooling
EMI
Immunity: EN61000-6-2
Emissions: EN50081-1
MTBF
1,500,000 hours at 30 C
min according to Bellcore
TR-NWT-000332
35 years min
Safety Approvals
Dimensions
WxHxD
Input UV protection
Input OV protection
Output
Tripping conditions
Overload
Short circuit
Manual ON/OFF
Pushbutton; protected
against accidental activation
Remote ON/OFF
Serial link
Overtemperature
Automatic
Mechanical Drawings
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Applications
Telecom
IT
Industrial
Description
The Magnum REC-J200EH Rectifier is a 12,000-watt electronic three-phase, switch-mode power supply module
which provides low total harmonic distortion (THD). Designed for superior performance in telecom, industrial, and IT
applications, its reduced size makes it one of the most compact force-cooled rectifiers in service to deliver 200
amps. Measuring 19" wide, 5.2" high, and with a depth of 19.09", this product has a power density in excess of
7 W/in3.
The REC-J200EH's combines a digitally-controlled, active Power-Factor-Correction circuit with an innovative
electronic design to achieve electrical efficiencies in excess of 90% and THD below 5%. It offers minimized cost and
reduced installation time, and its reliability ensures maximum system uptime for critical applications.
In addition, a "smart" user interface makes remote or local programming and monitoring of all major rectifier
parameters easy. Remote computer communications is available through an RS-485 serial connection interface
(SCI). The Magnum is UL listed and CSA, CE, IEC, and Broadcast NEBS Level 3 certified.
REC-J200EH
Input Voltage
Nominal
3-Phase
(Vrms)
Input
Frequency
Range (Hz)
Factory Set
Programmable
Output Voltage
(VDC)
Programmable
Output Voltage
Adjustment Range
(VDC)
Output
Current
(Amps)
380 to 480
47 to 63
-54.5
-40 to -60
200
Page 1 of 5
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ELECTRICAL SPECIFICATIONS
Input Specifications
Parameter
AC Input Voltage
Conditions/Description
3-phase, line-to-line.
Input Frequency
Min.
Nom.
Max.
Units
340
380 to
480
530
Vrms
63
Hz
10
47
Power Factor
> 0.99
W/VA
Total Harmonic
Distortion (THD)
<5
Turn-ON delay
4.5
sec
Input withstanding
voltage
560
Vrms
Max.
Units
VDC
60
VDC
Mains connector
Output Specifications
Parameter
Conditions/Description
Min.
Nom.
54.5
Output VDC
Adjustment Range
Programmable.
Ripple
BW 20 MHz.
Wide band, BW 20 MHz.
Psophometric noise CCITT weighted.
Electrical noise.
500
100
2
32
mVpp
mVrms
mVpp
dBrnc
Efficiency
92
Output Voltage
Regulation
0.4
Output Current
200
ADC
Thermally derated
current limit
Output Power
Continuous.
12
kW
Output Power
kW
Hold-up time
20
ms
500
ms
10
Current sharing
<5
Output connection
Page 2 of 5
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Fault Protection
Parameter
Conditions/Description
Min.
Nom.
AC Input Overvoltage
Protection
Input Breaker
Protection
Output Overcurrent
Protection
Current limitation:
220 ADC @ Vout 54.5 VDC.
200 ADC @ Vout = 60 VDC.
Output Overvoltage
Protection
Max.
Units
530
Vrms
37.5
70
Overtemperature (OT)
Protection
Overtemperature
driven by fan failure
36V
Overtemperature
threshold
Output Protection
350
Environmental Specifications
Parameter
Conditions/Description
Operating Temp
at Full Load
Linearly derated to 6 kW at 70 C.
Altitude
Operating.
Non-Operating.
Storage Temp
-5
-40
Humidity
Output Voltage
Temperature
Coefficient
EMI
EN 55022, class B.
Cooling
Min.
Page 3 of 5
Nom.
Max.
Units
55
13K
40K
ASL ft
ASL ft
85
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Interface Signals/Controls
Parameter
Conditions/Description
Alarms
Connection
Min.
Nom.
Max.
Units
Min.
Nom.
Max.
Units
Conditions/Description
cCSAus
Kema
Approved.
CB Report Approval
Approved.
Approved.
RoHS
Compliant.
Isolation
Mechanical Specifications
Parameter
Dimensions
Weight
Max.
Units
Depth (inches).
Conditions/Description
19.09
in
Depth (mm).
484.9
mm
Width (inches).
19.00
in
Width (mm).
482.6
mm
Height (inches).
5.21
in
Height (mm).
132.3
mm
Pounds.
50.26
lb
Kilograms.
22.8
kg
Page 4 of 5
Min.
Nom.
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Reliability
Parameter
Calculated MTBF
Conditions/Description
TR-TSY-000332 (excluding fans)
Min.
250,000
Nom.
Max.
Units
Hours
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Page 5 of 5
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
Extend the life of your network with the MIDI PODS enclosure platform, an ideal solution for all
wireless, fiber, and transmission networks.
The versatile MIDI PODS outdoor enclosure system supports valuable network equipment, backup
batteries, and power systems in a range of severe environmental conditions. The MIDI PODS has
a flexible and modular design matched with network equipment to provide a low impact solution.
The MIDI PODS rugged construction and a thermally-insulated power cabinet with sealed loop
heat exchangers or air conditioners ensures network integrity in the most challenging
environments. Its naturally-cooled battery cabinet provides a very cost-effective storage platform.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as
critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the
express written consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change
depending on the date manufactured. Specifications are subject to change without notice.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
23
DC Power
Distribution
19
Environmental Control
Mechanical
Heat exchanger
Air conditioners
Accessories
Power Cabinet
Dimensions (WxDxH)
Battery Cabinet
Dimensions (WxDxH)
Security
Cable Entry
Bottom
Service light
65
55
70/95
60
15
15
Aluzinc, powder coated
Circulating fans
Grounding bars
Weight
(kg)
Power
Battery
Plinth
Material
Mounting
Rugged Cabinet
Construction
Environmental
Protection
Distribution
Environmental
Management
Sealed loop heat exchangers
or air conditioners ensure
network integrity in the most
challenging environments.
DC Power
Rugged, flexible rectifier
options to match various load
& line conditions
65 C operating temperature
ensures maximum uptime in
high temperature environments
93.5% efficiencies reduces
thermal loads
Page 2 of 2
Up to 450 Ah batteries
DC Power Systems
AC load centers
9RU network equipment such
as radio base stations &
microwave equipment
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
The Power-One Prime Controller Card (PCC) is a pluggable microprocessor controller that provides
monitoring and control for a broad range of Power-One DC Power Systems. The PCC monitors all system
parameters including: DC voltage, rectifier current, rectifier temperature, system capacity, battery
parameters, and circuit breaker status.
Alarm and warning notifications are indicated by front panel LEDs, and through potential free alarm
contacts that allow remote signaling. External monitoring of alarms is accomplished through an RS232
port using PC-based PowCom software. The PCC has an optional Ethernet port allowing monitoring
and control over a TCP/IP network. Alarms can mapped via SNMP traps to customer OSS platforms such
as HP Openview
To meet individual site requirements, the PCC contains a Programmable Logic Unit that can be used to
monitor and control specified requirements. This allows individual alarm routing and logic operations to be
set as actions, alarms to be triggered, and outputs to be activated based on internal and external signal
monitoring, comparing, and processing.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as
critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the
express written consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change
depending on the date manufactured. Specifications are subject to change without notice.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Voltage
Current
Interface
Display
Dimensions
(WxHxD)
Weight
Operating
Temperature
-40 to +70 C
Storage
Temperature
-40 to +85 C
EMC
EN 61000-6-2, EN 61000-6-3,
EN 300 386-2
Storage:
ETS 300 019-2-1
Transport:
ETS 300 019-2-2
Operation:
ETS 300 019-2-3
Internal
Communication
External
Communication
Indications
Signal Input
Signal Outputs
Software
Environment
Battery Management
Battery
Disconnection
Boost
Charging
Battery Test
Symmetry
Measurement
Temperature
Compensation
Charging
Load
Shedding
(PLD)
Alarms
Alarm Contacts
Alarms
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
The Power-One Power Controller System (PCS) provides comprehensive monitoring and control for a
broad range of Power-Ones DC power systems. This digital controller monitors total system conditions
including DC voltage, rectifier current, rectifier temperature, system capacity, battery parameters and
circuit breaker status.
The PCS enables data storage of system configuration information such as battery type, installation date
and system commission date. In addition, the PCS is capable of monitoring up to 128 rectifiers and 128
sub-controllers within a power system. Visual notification of alarm and warning conditions are indicated
by front panel LEDs, while descriptions of the alarms are provided through an LCD or can optionally be
accessed remotely using a PC modem, or over a network using an optional Network Interface (PNI)
module.
To meet individual site requirements, the PCS contains a logic operator that can be programmed to
monitor and control specified requirements. This allows actions to be set, alarms to be triggered, and
outputs to be activated based on internal and external signal monitoring, comparing and processing.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Voltage
Current
Interface
Display
Internal
Communication
External
Communication
Indications
Controls
Signal
Collection
Software
Language
18 - 72 VDC
<200 mA at 48V, <400 mA at
24V
Battery
Battery Disconnection
Boost Charging
Battery Test
Symmetry Measurement
Alarms
Alarm History
Page 2 of 2
Temperature
Compensation Charging
PLD
Enhanced Battery
Monitoring
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
Extend the life of your network with the PODS enclosure platform, an ideal solution for all wireless,
fiber, and transmission networks.
The versatile PODS outdoor enclosure system supports valuable network equipment, backup
batteries, and power systems in a range of severe environmental conditions. The PODS flexible and
modular design allows cabinets to be paralleled and matched with network equipment.
The PODS rugged seismic-rated aluminium construction with direct fan cooling, sealed loop heat
exchangers or air conditioners ensures network integrity in the most challenging environments.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change
depending on the date manufactured. Specifications are subject to change without notice.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Electrical
DC Power
Distribution
Environmental Control
Heat exchanger
Air conditioners
Fan filter
Mechanical
Dimensions
(WxDxH)
Security
Cable Entry
Weight (excl
equipment)
Material
Mounting
Equipment
Mounting
Height
Width
Depth
Accessories
Cable bridges
Heater
Up to 200 kg
Grounding bars
Mains, DC, RF
Marine-grade aluminum
PAD mounted; installation via
removable lifting eyes
Service light
Smoke Detector
Standards Compliance
27, 40, & 49 RU
23" (with various 19" options)
600 mm, 24"
Safety
Environmental protection
Seismic
Environmental
Management
DC Power
Rugged, flexible rectifier
options to match various
load & line conditions
o
65 C operating
temperature ensures
maximum uptime in high
temperature environments
93.5% efficiencies reduce
thermal loads
Flexible DC load center
AC Distribution
Configurable with Surge
protection, RCCD, circuit
breakers, generator socket,
bypass switch
Rugged Cabinet
Construction
Rugged seismic-rated aluminum
construction
Lockable cabinet including vandalproof hinges and multi-point locking
mechanism
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Applications
Telecom
IT
Industrial
Description
The SLI 15 Inverter Series provides an ideal solution for telecom, IT, and industrial applications. Due to innovative
technology solutions like the patent-pending "Compact Coil", the SLI 15 inverters pack 1500 watts of power into a
light (5.6 kg) and compact package that is mountable in 19" racks and is only one rack unit high. The SLI 15
Inverter Series offers four models for different input (24 and 48VDC) and output (115 and 230VAC) voltage
combinations. An integrated controller, along with an optional internal Static Transfer Switch (STS) enable flexible
and scalable systems which are truly "plug and play", and require no external subsystems. The inverters can be
stacked up to the power level needed by each application and also have the capability to be configured for
generating a 3-phase voltage source.
Electrical performance of the SLI 15 is exemplary of a top-of-the-market product with efficiency that peaks at 93%
and a patent-pending control algorithm that compensates current harmonics on the DC side without using bulky and
expensive filters. The SLI 15 includes a powerful on-board Digital Signal Processor (DSP) that allows easy
programming of main parameters through use of its front-panel keypad and LCD display. In addition, the SLI 15 can
be interfaced with an RS-485 serial communications link.
Output Voltage
Nominal (VAC)
Overall Output
Voltage Range
(VAC)
Frequency
Range (Hz)
SLI-24-115
24
115
100 to 120
47 to 63
SLI-24-230
24
230
200 to 240
47 to 63
SLI-48-115
48
115
100 to 120
47 to 63
SLI-48-230
48
230
200 to 240
47 to 63
Model
The following suffixes should be added to the model number to order options. For an internal Static Transfer
Switch, please add the suffix "-STS". For AC terminal blocks, please add the suffix "-SC". For Hot Plug version,
please add the suffix -HP. For Neutral tied to Ground, please add the suffix -GN.
Page 1 of 5
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ELECTRICAL SPECIFICATIONS
Input Specifications
Parameter
Conditions/Description
DC Input Voltage
Range
Input Current
Min.
Nom.
Max.
Units
20
40
24
48
36
72
VDC
100
48
Amps
<10
Amps
Inrush current
Output Specifications
Parameter
Conditions/Description
Min.
Nom.
Max.
1500
Units
Watts
115
230
120
240
VAC
60
Hz
93
Output Power
Output AC Voltage
Range
110
200
Frequency
50Hz/230Vac, 60Hz/115Vac
50
Efficiency
Load Power Factor
lagging or leading
Crest Factor
Ipk/Irms
Regulation in single
mode
Regulation in parallel
mode
Total Harmonic
Distortion
On Resistive Load.
0.33
1
4
Page 2 of 5
230
115
-3
-0.1
+1
+0.1
-6
-8.5
0
0
<2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Fault Protection
Parameter
Conditions/Description
Min.
Nom.
Max.
Units
Input Overcurrent
Protection
140
70
Amps
Input Overvoltage
Protection
24 VDC Models:
48 VDC Models:
37,5
74
VDC
Input Undervoltage
Protection
24 VDC Models:
48 VDC Models:
18
36
VDC
Output Overload
1610
1840
Surge
1750
2300
VA
Overvoltage Protection
Undervoltage
Protection
Overcurrent Protection
Safety Overcurrent
Protection
Short-Circuit
Protection
Overtemperature
Protection
Visual and acoustic indication 5 C before shutdown at Tamb > 65 C and at Tint > 100 C.
Protection Restore
Modes
The restore mode of each protection can be individually selected to "latch" or "auto-restart".
Environmental Specifications
Parameter
Conditions/Description
Operating Temp
at Full Load
Altitude
Operating.
Non-Operating.
Storage Temp
-25
-40
Humidity
Output Voltage
Temperature
Coefficient
Min.
Page 3 of 5
Nom.
Max.
Units
55
13K
40K
ASL ft
ASL ft
85
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Interface Signals/Controls
Parameter
Conditions/Description
LCD Panel
LED Indicators
4 LED indicators:
Front panel GREEN LED indicates inverter is ON.
Min.
Nom.
Max.
Units
Serial link
Conditions/Description
cCSAus
Approved.
Kema
Approved.
CB Report Approval
Approved.
Approved.
RoHS
Compliant.
Isolation
Min.
Nom.
Min.
Nom.
Max.
Units
Mechanical Specifications
Parameter
Dimensions
Weight
Max.
Units
Depth (inches)
Conditions/Description
14.94
in
Depth (mm)
379.5
mm
Width (inches)
19.00
in
Width (mm)
482.6
mm
Height (inches)
1.71
in
Height (mm)
43.5
mm
Pounds
12.34
lb
5.6
kg
Kilograms
Connections
DC input: back left, one 6mm diameter hole at each input bar; hot plug version has PCB bars with
pre charging system; subrack for -HP version hosts one inverter, separate purchasing part; plastic
DC input cover is available, separate purchasing part
AC output: back right, IEC320 plug is the standard; screw terminal blocks are with the option SC;
-STS version has IEC320 socket marked Grid Input
Signal: back centre, female Sub-D 15 poles connector, Molex 89263-6062 or equivalent; general
failure alarm, serial port, synchronism for paralleling or three phase, remote on/off.
For paralleling inverters, up to 6, ask for paralleling kit, one per inverter, separate purchasing part
Important: -STS and -GN options are compatible just supplying Grind Input by means of an
isolation transformer, same indication if Neutral is tied to Ground at customer site.
Page 4 of 5
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Reliability
Parameter
Calculated MTBF
Conditions/Description
At 40 C excluding fan
-STS version, at 40C excluding fan
Min.
250,000
200,000
Nom.
Max.
Units
Hours
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Page 5 of 5
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Applications
Telecom
IT
Industrial
Description
The SLI 50 Series of Slim Line inverters provides an ideal solution for telecom, IT, and industrial
applications. Due to innovative technology solutions like the patent-pending Compact Coil", the SLI 50
Series inverters pack 5000 watts of power into a compact package that is 19 rack mountable and only
two rack units high. Electrical performance of the SLI Series inverter products is at the top of the
market with efficiency that peaks at 93% and a patent-pending control algorithm that compensates
current harmonics on the DC side without using bulky and expensive filters. The inverter includes an
on-board powerful Digital Signal Processor (DSP) that allows easy programmability of the main
parameters on the front panel LCD display and keypad.The SLI Series inverters can be interfaced with
RS485.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
LCD panel *
Inrush current
LED indicators *
Power-On
Input OC protection
Generic Fault
Input OV protection
Over Temperature
Input UV protection
Fan Fail
Data Communications
Output
Output power
5000 W
Frequency
50 or 60 Hz%
Overload
Efficiency
Up to 93%
Load PF
Load CF
Operating humidity
0 - 90% non-condensing
Load regulation
Altitude: operating
Altitude: non-operating
40000 feet
Output voltage
temperature coefficient
Line regulation
Distortion
Safety agency
compliance
Overvoltage protection
Isolation
Primary-to-secondary
3000 Vrms
Undervoltage protection
Primary-to-ground
1000 Vrms
Overcurrent protection
Secondary-to-ground
1500 Vrms
Safety overcurrent
protection
Signal-to-ground
0 Vrms
Short-circuit protection
Overtemperature
protection
Protection restore
modes
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Applications
Telecom
IT
Industrial
Description
The SLI 7 Series, Slim Line Inverter, provides ideal solutions for telecom, IT, and industrial applications.
It has lightweight (4 kg) and compact (1U x 19" x 14.8") design, and features peak efficiency up to 90%
with a true sine wave output.
A unique, patent-pending algorithm compensates current harmonics at the DC side, resulting in
extended battery life, reduced dimensions, and improved power density.
Model Selection
Model
SLI 7 24-230
SLI 7 48-230
Input Voltage
(VDC)
24
48
Output
Vo (VAC)
230
230
Page 1 of 2
Io (AAC)
3
3
Power
max (W)
700
700
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
48 VDC, 24 VDC
Efficiency
90%
Safety compliances
Input current
Input UV protection
EN60950:2000,
CSA-C22.2 No. 60950-00,
UL60950, IEC60950
EMI
EN55022 class A
Input OV protection
Operating temperature
Input withstanding
voltage
-25 C to 55 C, 700W.
Linear derating of
-40W/ C up to 65 C
Input protection
Storage
-40 C to 85 C
Cooling
0.4%
MTBF
250,000 hours
Dimensions
WxHxD
19" x 1U x 14.76"
(482.6 x 43.5 x 37.5mm)
Output
Output power
700W / 800VA
max continuous
Weight
4 kg
Output connection
Output voltage
Input connection
Output frequency
50-60 Hz 0.2%
Load regulation
-3% / +1%
2% pk-pk
(20 Hz / 20 MHz)
Load PF
0.3
Load CF
Overvoltage protection
-370Vpk 2% catastrophic;
latching, 2 ms delayed ;
-115% 2% of nominal;
auto-restart, 200ms delayed
Undervoltage protection
85% 2% of nominal;
auto-restart, 1S delayed
Overload
Overtemperature
protection
Internal Overtemperature
Protection
Shut down
Serial port
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Description
The XR04.48G (400 W) and XR08.48G (800 W) are a
family of single-phase, hot-pluggable, fan-cooled
rectifiers. The high power density of this product offers
the optimum 1U or 2U shelf solution for space-critical
applications.
Both rectifiers offer excellent efficiency as well as wide
operating temperature and wide input voltage range.
Together with advanced technology they enable cost
effective and reliable solutions.
XR04.48 Rectifier Module
The typical applications for this rectifier are both in
indoor and outdoor environments, which is ideal for
broadband access, cable head ends, micro/pico BTS
Cells, and Enterprise, E911, and GSM-R applications.
Features
Thermal protection
Hot Swappable
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model
XR04.48G
Input Voltage
85 to 300 VAC
(Nominal: 100-240 VAC)
Input Frequency
Max Input Current
(Nominal Input)
Max Inrush current
47 to 63 Hz
<5.5
Hold-up time
Fuse
20 ms (typ.)
Two 8A fast
blow (line &
neutral)
Operating
Temperature
Range
Storage
temperature
Relative
Humidity
Cooling
XR08.48G
<9.3A
Audible noise
Protection
Two 16 A fast
blow (line &
neutral)
LED
Indication
Output
Output Voltage
400 W
800 W
Output current
9.1 A max
18.2 A max
Efficiency
Load sharing
88 %(typ.) at
90 %(typ.) at
Iout nom
Iout nom
7.3 W/in3
14.6 W/in3
3% at load variation (10-90% /
90-10%) recovery time 50ms
<5% of nominal current
Output ripple
Psophometric noise
Power Density
Transient Response
Alarms via
RS485
Environment
Storage
Transport
Operation
Damp Heat
Mechanical
Dimension WxHxD
Weight
Pmax
Po
Po
Product
Safety
EN60950-1:2001
IEC60950-1-2001
EMC
EN61000-6-3:2001
EN61000-6-2:2001
EN60950-1/A11:2004
Emission
Immunity
Reinforced
Insulation
-40V
Temp
+65 +75
85V
Vin
Safety
Output Characteristic
Pmax
300V
Approvals
Basic
Functional
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Description
The Power-One Xscend rectifier provides
extremely reliable, high density DC power. The
rectifier incorporates the latest in power
monitoring solutions through an internal
microprocessor giving up-to-the-second updates
to the system controller and adjacent rectifiers.
This guarantees tightly-controlled load sharing
among rectifiers and provides status and
identification information to the controller.
At only two rack units high, these compact
universal input rectifiers provide up to 1600
watts and allow up to five rectifier modules in a
23-inch shelf or four modules in a 19-inch shelf.
Designed with diversity in mind, the Xscend
rectifier is able to operate in a complete range of
indoor and outdoor applications.
Features
Page 1 of 2
Front or mid-mountable
Hot-swappable
No adjustments required
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Mechanical
Input
Model
XR1648
Input Voltage
XR1424
Dimensions
(WxHxD)
Weight
Cooling
Insulation
Current (max.)
<10 A
Soft Start
<13 A/1 ms
Harmonics
>0.98 typical
Surge Immunity
EN 61000-4-5
Fuse
Connection
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Mounting
Protection
Alarms
Indications
Green LED
Power ON
Yellow LED
Red LED
Module failure
Output
Model
XR1648
Output Voltage
45-57 VDC
22.5-28 VDC
Power (max.)
1600 W
1400 W
at >180 VAC
(50-57 VDC)
at >180 VAC
(25-28 VDC)
675 W
675 W
at 180-85 VAC
(50-57 VDC)
at 180-85 VAC
(25-28 VDC)
Current (max.)
32 A
56 A
Efficiency
(at 40-90% load)
>93%
>90%
(93.5% typical)
(91% typical)
Tolerance
XR1424
Transient
Response
Audible Noise
<60dBA
10-90% or 90-10%
<5% of nominal current
Operating
Temperature
Load Sharing
Ripple
-40 to +85 C
Psophometric
Storage
Temperature
Radiated EMC
EN 61000-6-2, EN 61000-6-3,
Connection
EMC
EN 61000-6-2, EN 61000-6-4
Storage:
Transport:
Operation:
Earthquake:
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Shelf System
Input
Model
Xscend 23 Shelf
Xscend 19 Shelf
Input
20
16
10
(max.)
25
20
24V DC Version
Yes
48V DC Version
Yes
Yes
Supervision
XCS
XCS
Expansion
Yes
Yes
Inputs
(max.)
Output
Rectifier Modules
(max.)
External Distribution
(up to 2 shelves)
Yes
Features
Description
Xscend modular DC power shelf systems
provide large power system features in costeffective, rack-mounted form factors. These
shelf power solutions provide rectification,
system management and power distribution
while maintaining high reliability and offering
flexibility for future expansion. The Xscend
systems are based on hot-swappable
rectifier modules with constant output power
available at 1400 (24V) or 1600W (48V) per
module.
Battery
Battery Symmetry Inputs
(max.)
Yes
Yes
Mechanical
Dimensions (WxHxD)
584x133x274mm
(23x5.25x10.8in.)
483x133x274mm
(19x5.25x10.8in.)
Mounting
23
19
Cable Entry
Rear
Rear
Options
Temp. Comp. Charge
Yes
Yes
Ethernet Network
Interface
Yes
Yes
Modem Interface
Yes
Yes
Features
TM
www.power-one.com
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Configurations
System Components
Rectifier Modules
The Xscend system utilizes plug-in rectifier modules that are
based on a soft-switching approach. Features include 3 LEDs for
power-on, current limit & thermal protection, and module failure.
Rectifier Features
Model
Voltage
Power
(max.)
Current
(max.)
XR 1648
48V DC
1600W
32A
XR 1424
24V DC
1400W
56A
Supervision Modules
Advanced system supervision is accomplished using a
microprocessor based control module that allows both local
and remote system monitoring.
PCS Features
Distribution Module
Advanced distribution is accomplished using a 5U high
external distribution shelf. The shelf is based on
standard plug in circuit breakers and is available in 23in.
and 19in. configurations.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Configurations
System Components
Rectifier Modules
The Xscend system utilizes plug-in rectifier modules that are
based on a soft-switching approach. Features include 3 LEDs for
power-on, current limit & thermal protection, and module failure.
Rectifier Features
Model
Voltage
Power
(max.)
Current
(max.)
XR 1648
48V DC
1600W
32A
XR 1424
24V DC
1400W
56A
Supervision Modules
Advanced system supervision is accomplished using a
microprocessor based control module that allows both local
and remote system monitoring.
PCS Features
Distribution Module
Advanced distribution is accomplished using a 5U high
external distribution shelf. The shelf is based on
standard plug in circuit breakers and is available in 23in.
and 19in. configurations.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Shelf System
Input
Model
Xscend 23 Shelf
Xscend 19 Shelf
Input
20
16
10
(max.)
25
20
24V DC Version
Yes
48V DC Version
Yes
Yes
Supervision
XCS
XCS
Expansion
Yes
Yes
Inputs
(max.)
Output
Rectifier Modules
(max.)
External Distribution
(up to 2 shelves)
Yes
Features
Description
Xscend modular DC power shelf systems
provide large power system features in costeffective, rack-mounted form factors. These
shelf power solutions provide rectification,
system management and power distribution
while maintaining high reliability and offering
flexibility for future expansion. The Xscend
systems are based on hot-swappable
rectifier modules with constant output power
available at 1400 (24V) or 1600W (48V) per
module.
Battery
Battery Symmetry Inputs
(max.)
Yes
Yes
Mechanical
Dimensions (WxHxD)
584x133x274mm
(23x5.25x10.8in.)
483x133x274mm
(19x5.25x10.8in.)
Mounting
23
19
Cable Entry
Rear
Rear
Options
Temp. Comp. Charge
Yes
Yes
Ethernet Network
Interface
Yes
Yes
Modem Interface
Yes
Yes
Features
TM
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
www.power-one.com
DMAC
Controller
Description
The Power-One Digital Meter, Alarm and Control Panel (DMAC) provides comprehensive
monitoring and control for Power-Ones Compac power systems. This digital controller
monitors system conditions including DC voltage and load current, while providing a
variety of alarm and control functions.
DMAC features include user-configurable battery testing, measurement of battery voltage
and current & battery equalization.
Features
Single point system voltage adjust
Programmable timer for battery test or
equalization
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
DMAC
Controller
Interface
Display
Operating
Temperature
-0 to +50C
Digital Meters
Storage
Temperature
-50 to +85C
UV/OV
Adjustment
Humidity
Equalization &
Battery Test
Timer Range
Altitude
Range
Current
Measurement
DC Shunt
1200A:50mA
User Controls
Connection
Points
Temperature Compensation
Alarms
Alarms
Equalize alarm
OV/UV alarm
Major alarm
Minor alarm
Rectifier fail
Breaker alarm
Overview
The temperature
compensation panel works in
conjunction with the DMAC
controller. Temperature
compensation automatically
adjusts the float voltage
according to the ambient
temperature.
Temperature
Compensation
Alarms
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
EAU Module
Description
Features
TCP/IP Network
10Base-T Ethernet
Nine external inputs
Telnet for system setup
10Mbit 7-port HUB
Easy implementation
EAU
Wall Mount
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Monitoring
PowCom Monitoring
Remote system monitoring is accomplished through
PowCom and Alarm Central software packages.
PowCom is a graphic user interface site monitoring
program that allows remote access to system
parameters, alarm history, and battery test data at a
single system location.
Alarm Central allows multiple power systems to be
monitored using a hierarchy based window system
that informs a user of system events, using both
audible and visual alarms.
SNMP Monitoring Software
System monitoring can also be accomplished
through standard SNMP protocols and an enterprise
specific Management Information Base (MIB).
SNMP allows the user to access and monitor system
parameters as well as tracking system variables.
Supply Voltages
40 to 60VDC, max 5W
Ethernet Controller
Ethernet HUB
7-ports, 10Base-T
External Inputs
Weight
Dimensions (WxHxD)
Ambient Temperature
-10C to +70C
Storage Temperature
-40C to +85C
Mechanical
Environmental
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Description
The Integrity-One Power System is the next
generation solution for today's power system
needs. Using a modular design, the system is
easily upgradeable for future growth. With a
capacity up to 1250 amps, the Integrity-One
system is ideal for either central office or cell
site applications. This system includes multiple
options for user-friendly local and remote
access.
Basic design concepts allow the user to develop
system configurations that meet initial network
capacity requirements with minimum installation
costs while allowing future capacity expansion
through module additions or multi-bay
configurations. This is accomplished by a wide
variety of hot swappable modules, rectifiers and
distributions.
Standard features in each Integrity system
include an advanced microprocessor controller
(PCS). This controller offers an extensive list of
monitoring and control features that can be
accessed locally or remotely through the
standard RS232 connection or through the
optional Power-One Network Interface box,
which allows communication through Ethernet
and SNMP protocols. External reporting can
also be accomplished by using on-board FormC contacts.
In addition to the three systems listed here,
other layouts and individual components are
also available for integration into customer
provided equipment racks, cabinets, outdoor
enclosures, or other power requirements.
Please contact Power-One for assistance with
your unique requirements.
Features
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
Distribution Panels
Hot-swappable distribution shelves
Front, middle and rear distribution
positions (waterfall effect) allow for
system cable management
SDS: Secondary Distribution Shelf
Rated at 500A
Plug in CBs up to 100A rating
Plug in fuses up to 100A rating
Accommodates up to 22 circuit
breakers or fuses
PCS Controller
RS485 digital signal data bus
Fully programmable
6 programmable
alarms(upgradeable to 24)
Battery test: manual or automatic
Alarm relay test
Adjustable battery current
Software controlled start-up after
mains outage
Rectifier Shelves
RS485 communication bus
23 shelf allows up to 5 rectifiers
each
Digital current sharing
Individual rectifier or single shelf
AC feed options
PMP25 Rectifier
5 rectifiers into each 4U 23 shelf
Available in 24 or 48VDC
Thermal protection
Fan cooled modules with speed
control and alarms
Hot-swappable
RS485 interface
Low weight
Up to 91% efficiency
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Integrity-One 48V
Integrity-One 24V
Input
Single or individual
Single or individual
Inputs
Single input
Fuse
Rectifier Modules
50-1250A
110-1100A
Voltage
48V
24V
Efficiency
>91%
>89%
Controller
PCS Controller
PCS Controller
Rectifier
PMP 25.48
PMP 25.24
Output
Components
Compliance
EMC
Safety
Mechanical
Dimensions (WxHxD)
23 x 84 x 23 in.
(584 x 2133 x 584mm)
23 x 46 x 23 in.
(584 x 1168 x 584mm)
Mounting (rack)
23
23
Mounting (base)
Audible Noise
<60dBA
<60dBA
Operating Temperature
-25 to +60C
-40 to +65C
Storage Temperature
-40 to +85C
-40 to +85C
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
User controls and interfaces:
Description
The PCU10 provides monitoring and control for the PPS 10, 11, and 13 power systems. These hotswappable controller modules supervise AC inputs, output voltages and currents, rectifier performance,
battery condition, and breaker status. Visual notification of an alarm condition is provided with an LED. A
description of the exact alarm condition is provided through an LCD. Additionally, four Form C contacts
are provided to indicate a failure.
Page 1 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Voltage
Current
Dimensions
(WxHxD)
Weight
Interface
Display
Communications
Indications
Controls
Operating
Temperature
62 x 262 x 232mm
(2.4 x 10.3 x 9.1in)
0.5kg (1.1 lb.)
-25 to +55 C
Storage
Temperature
-50 to +85 C
Environment
Storage:
Transport:
Operation:
Battery Management
Alarms
The last 40 events are saved and
include a time and date stamp.
Four potential free change over
Alarm Contacts
alarm contacts. Two open collector
outputs for LVD.
Alarms
1*
High DC Voltage
1*
Low DC Voltage
1*
Load/ Battery Disc.
1*
Battery Fuse Failure
1*
DC Fuse Failure
2*
Module Failure
1*
Urgent Module Failure
3*
Main AC Failure
4*
Battery Failure
4*
Symmetry Failure
4*
High Temperature
2*
High Load
* All alarms are indicated using an LED and displayed in
the LCD. The numbers represent an example of alarm
routing: 1) Urgent alarm, 2) Service alarm,
3) Main AC failure, 4) Battery related failure
Alarms are configurable by changing the EPROM
Alarm History
Battery
Disconnection
Boost
Charging
Battery Test
Symmetry
Measurement
Temperature
Compensation
Charging
Load
Shedding
(PLD)
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCU 5/7
Controller
The PCU 5/ 7
Controllers are used
in PPS5 and PPS7
Power Systems.
Description
The Power-One Control Unit (PCU 5/7) provides monitoring and control for the PPS 5 and PPS 7
power systems. These hot-swappable controller modules supervise output voltages, currents, rectifier
performance, battery condition, and breaker status. Visual notification of an alarm condition is
provided with an LED. A description of the exact alarm condition is provided through an LCD.
Additionally, four Form C contacts are provided to indicate a failure.
Features
Intelligent battery management:
Capacity testing
compensation factor
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCU 5/7
Controller
Input
Alarms
Voltage
18-72V DC
Current
Alarm
History
Alarm
Contacts
Alarms
High DC Voltage
Low DC Voltage
Load/ Battery Disc.
Battery Fuse Failure
DC Fuse Failure
Module Failure
Urgent Module Failure
Main AC Failure
Battery Failure
Symmetry Failure
High Temperature
High Load
Interface
Display
Communication
Indications
Power ON
System warning message
System alarm
Controls
Battery Management
Battery
Disconnection
Boost Charging
Battery Test
Symmetry
Measurement
Temperature
Compensation
Charging
PLD
1*
1*
1*
1*
1*
2*
1*
3*
4*
4*
4*
2*
62 x 129 x 231mm
(2.4 x 5.1 x 9.1in.)
Weight
0.45kg (1.0lbs.)
Operating
Temperature
-25 to +55C
Storage
Temperature
-50 to +85C
Environment
Storage:
Transport:
Operation:
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 11
Rectifier Module
Description
The Power-One PMP 11 rectifier module
provides cost-effective power in a high
density solution. Built on the latest
advances in the resonance switch mode
approach (soft-switching), the PMP 11 is
the next evolution in our convection
cooled rectifier series.
Optimized for telecom applications, the
module is designed to work in a multitude
of different subrack/shelf configurations
incorporating the PCU/PCS controller and
varying distribution options.
Features
208/240 VAC input
24V, 48V, or 60V DC output
Input overvoltage disconnection
Thermal protection
Active load sharing
Hot-swappable
Up to 92% efficient
International standards compliance
Natural convection cooling
Low weight
PPS 10 6500 System
Shown
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 11
Rectifier Module
Input
Mechanical
Dimensions
62 x 261 x 231mm
(2.4 x 10.3 x 9.1in.)
Weight
3.1kg (6.8lbs.)
Current
(max.)
<6.8A
Cooling
Natural convection
Soft Start
Harmonics
EN 61000-3-2
Power Factor >0.99 at max. load
Surge
Immunity
EN 61000-4-5
Enclosure
IP20
Fuse
T 8A
Mounting
Connection
IEC-320/C14
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Model
PMP 10.24A
Input
Voltage
PMP 11.48
<7.0A
PMP 11.60
<7.0A
Insulation
EN 60950
UL 1950 and IEC60950 , Class 1
CSA C22-2 No. 950
Protection
Output
Model
PMP 10.24A
PMP 11.48
PMP 11.60
Output Voltage
22-28V DC
44-56V DC
56-71V DC
Power (max.)
1000W
(25-28V)
1100W
(50-57.7V DC)
1100W
(60-71V DC)
Current (max.)
43A
23A
18.5A
Efficiency
(at 40-90% Load)*
>88%
>91%
>92%
Tolerance
Vout +/- 1%
Green LED
Power ON
Red LED
High output
voltage/ shutdown
Red LED
Low voltage/
module failure
Indications
Transient
Response
Load Sharing
Ripple
Psophometric
Connection
EMC
Audible
Noise
<35dBA
Operating
Temperature*
Storage
Temperature
-40 to +85C
Radiated EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Environment
Storage:
Transport:
Operation:
DIN 41612F
EN 61000-6-2, EN 61000-6-4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Description
The PMP 13.48 is a convection-cooled rectifier
delivering superior reliability in harsh environmental
conditions where fan-cooled products may not
deliver the reliability required to ensure maximum
network asset performance.
With leading-edge patented resonant conversion
topology, the PMP13 industry-leading efficiencies of
93.5% deliver significant operating expenditure
savings in the network on utility and HVAC costs.
Power-One also recognizes that typical network
loads operate between 20-60%; hence the PMP13
unique flat efficiency ensures minimal energy loss
down to 15% of installed capacity
The PMP 13 is optimized for telecom applications,
and is designed to work in PPS10 systems
incorporating the PCS controller and various
distribution options with up to 6 units per 19/6U shelf
and up to 8 units per 23/6U shelf.
Features
Page 1 of 2
48 VDC output
Thermal protection
Hot swappable
Up to 92% efficient
Low weight
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Mechanical
Input
Model
PMP 13.48
Input Voltage
Current (max.)
Soft Start
Harmonics
EN 61000-3-2
Power Factor >0.99 at max. load
Surge
Immunity
EN 61000-4-5
Fuse
T 10A
Connection
IEC-320/C14
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Dimensions
(WxHxD)
62 x 261 x 231 mm
(2.4 x 10.3 x 9.1 in)
Weight
Cooling
Natural Convection
Insulation
Enclosure
Mounting
Protection
Output
Model
13.48
Output Voltage
44 - 56 VDC
Power (max.)
Current (max.)
1300 W at
50-56 VDC
28 A
Efficiency
>92%
(at 40-90%
load)*
Indications
Tolerance
Vout 1.0%
Transient
Response
Load Sharing
Ripple
Psophometric
Connection
DIN 41612F
EMC
EN 61000-6-2, EN 61000-6-4
Page 2 of 2
EN 60950
UL 1950 and IEC60950 , Class 1
CSA C22-2 No. 950
Short-circuit proof, automatic
current limiting, selective shutdown
of modules at excessive output
voltage. Thermal protection
reduces the output power at
environmental temperatures above
maximum level. Shut down at
>75 C with an automatic restart.*
Input overvoltage disconnection at
>275 VAC with automatic reset at
>260 VAC.
Green LED
Power ON
Red LED
High output
voltage/
shutdown
Red LED
Low voltage/
module failure
Audible
Noise
<35 dBA
Operating
Temperature
Storage
Temperature
-40 to +85 C
Radiated
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Environment
Storage:
Transport:
Operation:
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 25
Rectifier Module
Description
The Power-One PMP 25 rectifier uses
resonance switch mode technology (soft
switching), and incorporates thermal
protection while providing extremely reliable
DC power in a small space. Rectifier
communication is accomplished using digital
interfaces over an RS485 data bus.
Information is transmitted to adjacent
rectifiers while providing status and
identification information to the system
controller (PCS).
At only 4 rack units high, these compact
rectifiers allow for up to five modules in each
23in. rack (4 units in 19in. rack) providing up
to 250A at 48V or up to 550A at 24V. With
full power available up to 65C, PMP 25
rectifiers are ideal for any indoor or outdoor
application.
Features
Compact 4 rack-unit height
50A output at 48V
110A output at 24V
208 / 240 single phase input
Input over-voltage disconnect
Hot-swappable rectifiers
High efficiency, up to 91%
Active current sharing
International standards compliance
PPS 25 System
Shown
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 25
Rectifier Module
Input
Mechanical
Dimensions
Weight
6.2kg (13.6lbs.)
Current
(max.)
<22A
<20A
Cooling
Soft Start
<22A
<20A
Interface
Harmonics
EN 61000-3-2
Power Factor >0.98 at 50-100% load
Surge
Immunity
EN 61000-4-5
Fuse
F 25A
Connection
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Model
PMP 25.24
Input
Voltage
PMP 25.48
Output
Model
PMP 25.24
PMP 25.48
Power (max.)
3080W
2800W
Output Voltage
22-30V DC
44-58V DC
Current (max.)
110A
50A
Efficiency
>89%
>91%
(@ 40-90%Load)*
Tolerance
Load Sharing
Psophometric
Connection
EMC
IP20
Mounting
In 19/ 4U subrack up to 4
In 23/ 4U subrack up to 5
EN 60950
CSA C22-2 No. 950, UL 1950
Protection
Power ON
Yellow LED
Thermal Protection
Yellow Flashing
Comm. Error
Red LED
Module Failure
Indications
Audible
Noise
<60dBA
Operating
Temperature*
Storage
Temperature
-40 to +85C
Radiated EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Environment
Storage:
Transport:
Operation:
EN 61000-6-2, EN 61000-6-4
Enclosure
Transient
Response
Ripple
Insulation
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 5
Rectifier Module
Description
The Power-One PMP 5 rectifier module
provides a cost-effective power solution
in a high density footprint. Built on the
latest advances in the resonance switch
mode approach (soft-switching), the
PMP 5 is the next evolution in our small
convection cooled rectifier series.
Optimized for telecom applications, the
module is designed to work in a
multitude of different subrack/shelf
configurations incorporating the PowerOne PCU controller and various
distribution options.
Features
115/230 VAC input
24V, or 48VDC output
Power factor correction
Active load sharing
Hot-swappable
PPR 5/7 System
Shown
Low weight
Natural convection cooling
International standards compliance
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 5
Rectifier Module
Input
Mechanical
PMP 5.48
PMP
5.24-110
PMP
5.48-110
Model
PMP 5.24
Input
Voltage
195-276V AC single
phase, (44-66Hz)
93,5-148,5V AC single
phase, (44-66Hz)
Current
(max.)
<2.9A
<5.8A
Dimensions
62 x 129 x 232mm
(2.4 x 5.1 x 9.1in.)
Weight
1.5kg (3.3lbs.)
Cooling
Natural convection
Insulation
Soft Start
Harmonics
EN 610555
Power Factor >0.99 at 50-100% load
Surge
Immunity
EN 61000-4-5
Fuse
T 3,15A
Connection
IEC-320/C14
EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
T 6A
Enclosure
IP20
Mounting
In 19 subrack up to 6 modules
EN 60950
Protection
Output
Model
PMP 5.24
PMP 5.48
PMP
5.24-110
PMP
5.48-110
Output
Voltage
22.5-28
VDC
45-56
VDC
22.5-28
VDC
45-56
VDC
Power (max.)
448W
448W
448W
448W
Current
(max.)
16A
8A
16A
8A
Efficiency
>87%
>89%
>85%
>87%
Tolerance
Vout +/- 1%
Transient
Response
Green LED
Power ON
Red LED
High output
voltage/ shutdown
Red LED
Low voltage/
module failure
Indications
Audible
Noise
<35dBA
Operating
Temperature
-25 to +55C
Storage
Temperature
-40 to +85C
Load Sharing
Radiated EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Ripple
Storage:
Transport:
Operation:
Psophometric
Connection
DIN 41612F
EMC
EN 61000-6-2, EN 61000-6-4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 7
Rectifier Module
Description
The Power-One PMP 7 rectifier module
provides a cost-effective power solution
in the highest possible density. Built on
the latest advances in the resonance
switch mode approach (soft-switching),
the PMP 7 is the next evolution in our
small convection cooled rectifier series.
Optimized for telecom applications, the
module is designed to work in a multitude
of different subrack/shelf configurations
incorporating the Power-One PCU
controller and various distribution
options.
Features
208/240 VAC input
24V, 48V, or 60V DC output
Input overvoltage disconnection
Thermal protection
Active load sharing
Hot-swappable
Up to 92% efficient
International standards compliance
Natural convection cooling
PPS 7 3500 System
Shown
Low weight
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PMP 7
Rectifier Module
Mechanical
Input
Model
PMP 7.24
PMP 7.48
Input
Voltage
Current
(max.)
<3.55A
<4.35A
Dimensions
62 x 129 x 232mm
(2.4 x 5.1 x 9.1in.)
Weight
1.65kg (3.6lbs.)
Cooling
Natural convection
<4.35A
Soft Start
<11A peak
max. 5ms
Harmonics
EN 61000-3-2
Power Factor >0.99 at max. load
Surge
Immunity
EN 61000-4-5
Fuse
T 6,3A
Connection
IEC-320/C14
EMC
<15.5A peak
max. 5ms
PMP 7.60
<20A peak
max. 5ms
Insulation
Enclosure
IP20
Mounting
In 19 subrack up to 5 modules
EN 61000-6-2, EN 61000-6-3,
FCC Part 15 Class B
Safety
EN 60950
UL 1950 and IEC60950 , Class 1
CSA C22-2 No. 950
Protection
Output
Model
PMP 7.24
PMP 7.48
PMP 7.60
Output
Voltage
22.5-28VDC
45-56VDC
56-70.5VDC
Power (max.)
560W
672W
635W
Current
(max.)
20A
12A
9A
Efficiency
>89.5%
>92%
>92%
Green LED
Power ON
Red LED
High output
voltage/ shutdown
Red LED
Low voltage/
module failure
Indications
Tolerance
Vout +/- 1%
Transient
Response
Load Sharing
Audible
Noise
<35dBA
Ripple
Operating
Temperature*
Psophometric
-40 to +85C
Connection
DIN 41612F
Storage
Temperature
Radiated EMC
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Environment
Storage:
Transport:
Operation:
EMC
EN 61000-6-2, EN 61000-6-4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Description
Features
Page 1 of 2
System parameters
Alarm history
Uses
RS232,
RS485,
10Base-T Ethernet
and
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Web Interface
Serial Port
<2 W
18 to 72 VDC, max 2 W
10 BaseT Driver/ Receiver with line transformer and EMI filter
half-duplex Ethernet.
2 RS232 ports (1 for PCU/ Setup and 1 for Modem/ PC)
Mechanical
Weight
Environmental
Dimensions
Ambient Temperature
Storage Temperature
Compliance
Humidity
Ethernet
Serial Port
0% to 95% (non-condensing)
Supports IEEE 802.3 Ethernet Standard
Industry standard 16550 A-compatible UART
Electrical
Communication
Power Consumption
Supply Voltages
Ethernet
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as
critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the
express written consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change
depending on the date manufactured. Specifications are subject to change without notice.
Page 2 of 2
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PPR 5/7
Description
The Power-One PPR 5/7 3 and 6
position rectifier backplane provides a
cost-effective power solution in a high
density wall-mounted footprint. These
power solutions provide rectification,
system management, and power
distribution while maintaining high
reliability and offering flexibility for
future expansion. The PPS 5/7 3 & 6
Position systems are based on hotswappable rectifier modules output
power available at 450, 560 or 670W per
module.
Features
115/230 VAC input
24V, or 48VDC output
Serial or parallel alarm configurations
Active load sharing
Hot-swappable
International standards compliance
Natural convection cooling
6 Position System
Shown
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PPR 5/7
Input
Input Connections
Load Outputs
2x10mm - Qty 3
2x10mm - Qty 6
24V DC Version
Yes
Yes
48V DC Version
Yes
Yes
Output
Rectifier Modules
(max.)
Features
Alarms
Mechanical
Dimensions (WxHxD)
271x193.5x305mm
484.4x193.5x305mm
Weight
1.2kg (2.65lbs.)
2.5kg (5.5lbs.)
Mounting
Wall Mount
Wall Mount
Available Rectifiers
Model
Voltage
Power (max.)
Current (max.)
PMP 5.24
24V DC
448W
16A
24V DC
448W
16A
48V DC
448W
8A
24V DC
560W
20A
48V DC
672W
12A
*110V AC input
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Cabinet System
Cabinet System
Input
Model
PPS 10-10400
PPS 10-18200
PPS 10-23400
Input
230/400V 3-phase
208-240V 1-phase
Site configurable
230/400V 3-phase
208-240V 1-phase
Site configurable
230/400V 3-phase
208-240V 1-phase
Site configurable
Single input
14
18
20
21
24V DC Version
Yes
Yes
Yes
48V DC Version
Yes
Yes
Yes
60V DC Version
Inputs
(max.)
Output
Rectifier Modules
(max.)
(100A)
(2-63A)
PCS
PCU/PCS
Features
Supervision
Description
PCS
TM
Expansion
Expansion subrack
N/A
Yes
Yes
Expansion Cabinet
Yes
Yes
N/A
3/4
Features
Yes
Yes
Yes
In-Cabinet Battery
Yes
Yes
N/A
Dimensions (WxHxD)
Power Cabinet:
600x700x400mm
Battery Cabinet:
600x1130x400mm
600x1130x600mm
600x1800x400mm
600x1800x600mm
600x2000x400mm
600x2000x600mm
600x1750x400mm
600x2150x400mm
Cable Entry
Top
Top
Top/Bottom
Yes
Yes
Yes
Integrated Surge
Arrestors
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Battery Cover
Yes
Yes
N/A
Ethernet Network
Interface
Yes
Yes
Yes
Modem Interface
Yes
Yes
Yes
Battery
Mechanical
Options
High reliability
Simple installation and operation
LCD display for self-guided controller operation
Interfaces standards include RS232, and Form
C dry alarm contacts with grouped alarms
Intelligent battery management:
Temperature compensation
(requires optional cables)
Programmable battery load testing
with data logging
Symmetry (requires optional cables)
Programmable low voltage disconnect
Optional Ethernet (SNMP compatible) interface
module
Natural convection cooled - no fans
International standards compliance
www.power-one.com
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
System Configurations
Rectifier Modules
The PPS 10 system utilizes plug-in rectifier modules that are
based on a soft-switching approach. Features include 3 LEDs for
rectifier status indication, thermal shutdown and input
overvoltage disconnection with an automatic reset.
Rectifier Features
Model
Voltage
Power
(max.)
Current
(max.)
24V DC
1000W
43A
48V DC
1100W
22A
60V DC
1100W
19.5A
48V DC
1300W
28A
48V DC
1250W
27A
Supervision Modules
PCS Features
All of the features listed under PCU above, plus:
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
System Configurations
Rectifier Modules
The PPS 10 system utilizes plug-in rectifier modules that are
based on a soft-switching approach. Features include 3 LEDs for
rectifier status indication, thermal shutdown and input
overvoltage disconnection with an automatic reset.
Rectifier Features
Model
Voltage
Power
(max.)
Current
(max.)
24V DC
1000W
43A
48V DC
1100W
22A
60V DC
1100W
19.5A
48V DC
1300W
28A
48V DC
1250W
27A
Supervision Modules
PCS Features
All of the features listed under PCU above, plus:
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Cabinet System
Cabinet System
Input
Model
PPS 10-10400
PPS 10-18200
PPS 10-23400
Input
230/400V 3-phase
208-240V 1-phase
Site configurable
230/400V 3-phase
208-240V 1-phase
Site configurable
230/400V 3-phase
208-240V 1-phase
Site configurable
Single input
14
18
20
21
24V DC Version
Yes
Yes
Yes
48V DC Version
Yes
Yes
Yes
60V DC Version
Inputs
(max.)
Output
Rectifier Modules
(max.)
(100A)
(2-63A)
PCS
PCU/PCS
Features
Supervision
Description
PCS
TM
Expansion
Expansion subrack
N/A
Yes
Yes
Expansion Cabinet
Yes
Yes
N/A
3/4
Features
Yes
Yes
Yes
In-Cabinet Battery
Yes
Yes
N/A
Dimensions (WxHxD)
Power Cabinet:
600x700x400mm
Battery Cabinet:
600x1130x400mm
600x1130x600mm
600x1800x400mm
600x1800x600mm
600x2000x400mm
600x2000x600mm
600x1750x400mm
600x2150x400mm
Cable Entry
Top
Top
Top/Bottom
Yes
Yes
Yes
Integrated Surge
Arrestors
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Battery Cover
Yes
Yes
N/A
Ethernet Network
Interface
Yes
Yes
Yes
Modem Interface
Yes
Yes
Yes
Battery
Mechanical
Options
High reliability
Simple installation and operation
LCD display for self-guided controller operation
Interfaces standards include RS232, and Form
C dry alarm contacts with grouped alarms
Intelligent battery management:
Temperature compensation
(requires optional cables)
Programmable battery load testing
with data logging
Symmetry (requires optional cables)
Programmable low voltage disconnect
Optional Ethernet (SNMP compatible) interface
module
Natural convection cooled - no fans
International standards compliance
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
www.power-one.com
Features
High reliability
Simple installation and operation
LCD display for self-guided controller
operation
Interfaces standards include RS232, and
Form C dry alarm contacts with grouped
alarms
Intelligent battery management:
Temperature compensation (requires
optional cables)
Programmable battery load testing
with data logging
Symmetry (requires optional cables)
Programmable low voltage disconnect
Optional Ethernet (SNMP compatible)
interface module
Natural convection cooled - no fans
International standards compliance
Description
PPS 10 modular DC power shelf systems provide large power system features in cost-effective, rack-mounted
form factors. These shelf power solutions provide rectification, system management, and power distribution
while maintaining high reliability and offering flexibility for future expansion. The PPS 10 systems are based on
hot-swappable rectifier modules with constant output power available at 1300 W per module.
System management is accomplished through messages and alarms displayed on the system controllers
(PCU/PCS) LCD screen and can also be displayed remotely via the PC-based PowComTM software package.
Page 1 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Page 2 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
Rectifier Modules
The PPS 10 system utilizes plug-in rectifier modules that are based
on a soft-switching approach. Features include 3 LEDs for rectifier
status indication, thermal shutdown, and input overvoltage
disconnection with an automatic reset.
Rectifier Features
Model
PMP 13.48 SIC
Voltage
48 VDC
Power (max.)
1300 W
Current (max.)
28 A
Supervision Modules
Advanced system supervision is accomplished using a
microprocessor-based control module that allows both local and
remote system monitoring.
PCU Features
Menu-guided operation
RS232 interface for remote operation
Battery management and testing
Low voltage battery disconnect (LVBD)
Partial load disconnect (PLD)
Temperature compensation
Battery symmetry measurement
Optional Ethernet interface through SNMP and/or
TCP/IP
PCS Features
All of the features listed under PCU above, plus:
Advanced battery management and testing
Digital signal collection via internal RS485 bus
Site programmable flash EPROM
Multiple language choices
Programmable alarms
Programmable logic functions and operations
Monthly data logging
Page 3 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
Model
Input
Inputs (max.)
PPS 10-3900
230/400V 3-phase
208-240V 1-phase
Site configurable
Single input
PPS 10-7800
230/400V 3-phase
208-240V 1-phase
Site configurable
Single input
3
2
8
6
4
15
PCU
PCS
3
Yes
4
Yes
Yes
N/A
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Output
Rectifier Modules (max.)
Battery Outs - MCB (100 A)
Load Outs - MCB (2-63 A)
Features
Supervision
Battery
Battery Symmetry Inputs
Low Voltage Battery Disconnection
(LVBD)
Mechanical
Dimensions (WxHxD)
Mounting
Cable Entry
Options
Temp. Comp. Charge
Integrated Surge Arrestors
Partial Load Disconnect
Ethernet Network Interface
Modem Interface
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 4 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Features
Description
PPS 16 modular DC power shelf and cabinet systems are designed to meet rigid telecom applications with very
high reliability and flexibility for future expansion.
The PPS 16 Power Systems are based on hot-swappable rectifier modules with output power available up to
1800 watts per module.
System management is accomplished through messages and alarms displayed on the system controllers LCD
screen and can also be viewed and controlled remotely via the PC-based PowCom software package.
Page 1 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Cabinet Solutions
(With Batteries)
Floor cabinet solutions that
combine rectifiers, DC
distribution, backup batteries,
and monitoring in a single
footprint.
This system can accommodate
up to 10 rectifier modules, a
supervision module, and DC
distribution with up to 6 battery
breakers and 26 load breakers.
Up to 360 A/ 18 kW/ 48 V
per cabinet
Space for 680 Ah backup
batteries per cabinet
Footprint - 600 x 600 mm
or 600 x 400 mm
Height - 1800 or 2000
mm
Page 2 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
Rectifier Modules
The PPS 16 system utilizes plug-in rectifier modules that are
based on a soft-switching approach. Features include 3 LEDs
for rectifier status indication, thermal shutdown, and input
overvoltage disconnection with an automatic reset.
Rectifier Features:
Model
Input
Voltage
FMP16.48
FMP18.48
85-275 VAC
48 VDC
Power
(Max)
1600 W
1800 W
Current
(Max)
32 A
36 A
Controllers
PCS Features;
PCC Features;
PCS Module
PCC Module
Page 3 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Input
19 Shelf
Model
AC Inputs
23 Shelf
23 Cabinet
10
10
1-3
2 to 6
2-4
2 to 6
2-4
2 to 6
13
21
16
20
16
20
PCC
PCS
PCC
PCS/PCC
PCC
PCS/PCC
12
6 or 12
6 or 12
Output
Rectifier Modules
(max. per system)
Battery Outputs
Load Outputs (Max)
(MCB type dependant)
Controller
Model
Battery
Battery Symmetry
Inputs
Low Voltage Battery
Disconnect (LVBD)
In-Cabinet Battery
Yes
Yes
Yes
N/A
N/A
Up to 680 Ah using
4 x 170 Ah
Mechanical
Dimensions
W x H x D (mm)
483x355x300 483x355x300
(19 in. x 4U)
(19 in. x 8U)
483x355x300
(23 in. x 4U)
483x355x300
(23 in. x 8U)
Options
Temp. Comp. Charge
Yes
Yes
Yes
Ethernet Network
Interface
Yes
Yes
Yes
Modem Interface
Yes
Yes
Yes
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
Page 4 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Cabinet System
Input
Model
PPS 25 System
Input
Inputs
(max.)
Description
Output
Rectifier Modules
(max.)
Battery Outputs
Several battery breaker modules are available and are based on:
MCCBs: 1x1500A, 2x600A, 4x384A
MCBs: 12x100A
Knife fuses: 5xNH1-3
Several battery breaker modules are available and are based on:
MCCBs: 1x1500A, 2x600A, 2x384A, 4x384A
MCBs: 24x2-63A, 16x80-100A, 24x2-16A high ohmic
Knife fuses: 5xNH1-3, 9xNH00
(2-63A)
24V DC Version
48V DC Version
Yes
Features
Supervision
PCS
Expansion
TM
Expansion Rack
Expansion Cabinet
Features
Battery
Battery Symmetry Inputs
Mechanical
Dimensions (WxHxD)
600x2150x600mm
Cable Entry
Yes
Yes
Yes
Ethernet Network
Interface
Yes
Modem Interface
Yes
Options
Temp. Comp. Charge
High reliability
Simple installation and operation
LCD display for self-guided controller operation
Interfaces standards include RS232, and Form
C dry alarm contacts with grouped alarms
Up to 1200A per cabinet
Live expansion up to 6400A
Plug-in ready for various DC distributions and
subracks
Inter-cabinet DC paralleling bus
Site programmable supervision unit
Intelligent battery management
Optional Ethernet (SNMP compatible) interface
module
International standards compliance
www.power-one.com
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
System Configurations
Rectifier Modules
The PPS 25 system utilizes plug-in rectifier modules that are
based on a soft-switching approach. Features include 3 LEDs
for rectifier status indication, thermal shutdown, and input
overvoltage disconnection with an automatic reset.
Model
Voltage
Power
(max.)
Current (max.)
24V DC
3080W
110A at 28V DC
48V DC
2800W
50A at 56V DC
PMP 25 Rectifier
Supervision Module
Advanced system supervision is accomplished using a microprocessor
based control module that allows both local and remote system monitoring.
PCS Features
PPS 25 System
The PPS 25 system offers flexible solutions that fit a large number of site
requirements. Some of these features include:
Cabinet
Cabinet Features
DC Distribution
Plugable load distribution
module, based on MCBs,
MCCBs or knife fuses. Low
or high ohmic.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PPS 25 Cabinet
System Components
System Configurations
Rectifier Modules
The PPS 25 system utilizes plug-in rectifier modules that are
based on a soft-switching approach. Features include 3 LEDs
for rectifier status indication, thermal shutdown, and input
overvoltage disconnection with an automatic reset.
Model
Voltage
Power
(max.)
Current (max.)
24V DC
3080W
110A at 28V DC
48V DC
2800W
50A at 56V DC
PMP 25 Rectifier
Supervision Module
Advanced system supervision is accomplished using a microprocessor
based control module that allows both local and remote system monitoring.
PCS Features
PPS 25 System
The PPS 25 system offers flexible solutions that fit a large number of site
requirements. Some of these features include:
Cabinet
Cabinet Features
DC Distribution
Plugable load distribution
module, based on MCBs,
MCCBs or knife fuses. Low
or high ohmic.
PPS 25 Cabinet
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Cabinet System
Input
Model
PPS 25 System
Input
Inputs
(max.)
Description
Output
Rectifier Modules
(max.)
Battery Outputs
Several battery breaker modules are available and are based on:
MCCBs: 1x1500A, 2x600A, 4x384A
MCBs: 12x100A
Knife fuses: 5xNH1-3
Several battery breaker modules are available and are based on:
MCCBs: 1x1500A, 2x600A, 2x384A, 4x384A
MCBs: 24x2-63A, 16x80-100A, 24x2-16A high ohmic
Knife fuses: 5xNH1-3, 9xNH00
(2-63A)
24V DC Version
48V DC Version
Yes
Features
Supervision
PCS
Expansion
TM
Expansion Rack
Expansion Cabinet
Features
Battery
Battery Symmetry Inputs
Mechanical
Dimensions (WxHxD)
600x2150x600mm
Cable Entry
Yes
Yes
Yes
Ethernet Network
Interface
Yes
Modem Interface
Yes
Options
Temp. Comp. Charge
High reliability
Simple installation and operation
LCD display for self-guided controller operation
Interfaces standards include RS232, and Form
C dry alarm contacts with grouped alarms
Up to 1200A per cabinet
Live expansion up to 6400A
Plug-in ready for various DC distributions and
subracks
Inter-cabinet DC paralleling bus
Site programmable supervision unit
Intelligent battery management
Optional Ethernet (SNMP compatible) interface
module
International standards compliance
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
www.power-one.com
Description
Features
Page 1 of 4
High reliability
Simple installation and operation
LCD display for self-guided controller
operation
RS232 interface for remote operation
Intelligent battery management:
Temperature compensation (requires
optional cables)
Programmable battery load testing
with data logging
Symmetry (requires optional cables)
Programmable low voltage
disconnect
Optional Ethernet (SNMP compatible)
interface module
Natural convection cooling - no fans
International standards compliance
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Configurations
Page 2 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
System Components
Rectifier Modules
The PPS 7 system utilizes plug-in rectifier modules that
are based on a soft-switching approach. Features
include 3 LEDs for rectifier status indication, thermal
shutdown, and input overvoltage disconnection with an
automatic reset (only on PMP 7 modules).
Rectifier Features
Model
Voltage
Power (Max)
Current (Max)
24 VDC
560 W
20 A
48 VDC
672 W
12 A
Menu-guided operation
RS232 interface for remote operation
Battery management and testing
Low voltage battery disconnect (LVBD)
Temperature compensation
Battery symmetry measurement
Optional Ethernet interface through SNMP and/or TCP/IP
Partial load disconnection (PLD)
Page 3 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PPS 7-2100
PPS 7-2800
PPS 7-3500
Input
230/400V 3-phase
208-240V 1-phase
Site configurable
230/400V 3-phase
208-240V 1-phase
Site configurable
230/400V 3-phase
208-240V 1-phase
Site configurable
Inputs (max.)
Single input
Single input
Single input
Battery Outputs
Load Outputs
20
24 VDC Version
Yes
N/A
N/A
48 VDC Version
Yes
Yes
Yes
PCU
PCU
PCU
Yes
Yes
Yes
Output
Features
Supervision
Battery
Mechanical
Dimensions (WxHxD)
485x133x305 mm
Mounting
Cable Entry
Top
Top
Top
485x133x305 mm
485x266x305 mm
Options
Temp. Comp. Charge
Yes
Ethernet Network
Interface
Yes
Modem Interface
Yes
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use
as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without
the express written consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change
depending on the date manufactured. Specifications are subject to change without notice.
Page 4 of 4
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
XCS
Controller
Description
The Power-One Xscend Controller System (XCS) provides comprehensive monitoring
and control for Power-Ones Xscend DC power systems. This digital controller monitors
total system conditions including DC voltage, rectifier current, rectifier temperature,
system capacity, battery parameters and circuit breaker status.
The XCS enables data storage of system configuration information such as battery type,
installation date and system commission date. Visual notification of alarm and warning
conditions are indicated by front panel LEDs, while descriptions of the alarms are provided
through an LCD, or as an option, may be accessed remotely through a modem or a
Network Interface (PNI) module.
To meet individual site requirements, the XCS contains a logic operator that can be
programmed to monitor and control specified requirements. This allows actions to be set,
alarms to be triggered, and outputs to be activated based on internal and external signal
monitoring, comparing and processing.
Features
User controls and interfaces:
Capacity testing
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
XCS
Controller
Input
Voltage
18-72V DC
Current
Interface
Dimensions
(WxHxD)
483/584 x 44 x 274mm
(19/23 x 1.75 x 10.8in.)
Weight
4.94kg (11lbs.)
Operating
Temperature
-40 to +65C
Display
Internal
Communication
Storage
Temperature
-50 to +85C
Internal
Communication
Environment
Storage:
Transport:
Operation:
Indications
Power ON
System warning message
System failure message
Controls
Signal
Collection
Software
Language
Battery
Battery
Disconnection
Boost Charging
Battery Test
Symmetry
Measurement
Temperature
Compensation
Charging
PLD
Enhanced
Battery
Monitoring
Alarms
Alarm History
Alarm
Contacts
Alarms
1*
2*
4*
3*
4*
6*
5*
6*
6*
4*
5*
5*
4*
5*
4*
www.power-one.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com