Professional Documents
Culture Documents
Anchor Bolts & Plates
Anchor Bolts & Plates
Products
We supply a wide range of mechanical engineering products, manufactured either in-house by Maineport Ltd or sourced elsewhere according to our customers requirements. In house products include: Insulated specialist supports for high temperature and cryogenic pipe systems Acoustic Pipe Supports Slider Plate Assemblies Anchor Bolts and Plates Blinds and Spacers for pipelines Pipe Support Components Technical publications describing the products are available from our Sales Department.
Important Note
Maineport Ltds continuous improvement policy means that this catalogue may be updated check with our sales department. This information is for your guidance: if you require any further assistance, please contact our Sales Department.
Introduction
MAINEPORT LTD manufacture a standard range of anchor bolt assemblies for industrial and civil engineering applications. This catalogue will enable you to specify, select, purchase and install the bolting you require for your application. We also supply special bolting arrangements manufactured to customers requirements and any combination of length and projection for standard units, in 10mm increments.
L Overall Length
D E Nomsize
F Square
Dimensions in millimetres Bolt Type F 20 F 24 F 30 F 36 F 42 F 48 F 56 F 64 D Dia. 20 24 30 36 42 48 56 64 C Length of thread 100 125 125 150 150 K 175 225 225 E Sleeve dia. 75 100 100 100 150 150 150 150 F Plate Square 100 150 150 175 250 250 300 300 K 65 70 90 100 120 135 150 165 L Length P Projection 265 310 315 330 405 425 560 570
K + P + X
P Projection
Fig 2a
Protective cap for Type SC (Recommended for bolts of 30mm dia and over)
Section Y-Y G
Dimensions in millimetres
Bolt Type S 20 S 24 S 30 S 36 S 42 S 48 S 56 S 64 D Dia 20 24 30 36 42 48 56 64 A 235 285 330 450 500 560 615 620 B Cap 50 55 65 80 90 105 115 120 C Length Of thd 100 125 125 150 150 175 225 225 E Sleeve Dia 75 100 100 100 150 150 150 150 F Plate Sq 100 150 150 175 250 250 300 300 G 42 48 60 71 81 91 105 115 H Depth 275 330 385 515 575 645 710 720 Short Series (S) L P 360 85 420 90 505 120 655 140 725 150 795 150 870 160 880 160 Long Series (S) L P 540 265 640 310 700 315 845 330 980 405 1070 425 1270 560 1290 570
Bolt sizes over 64mm dia. are available to special order. Cap depth B is the minimum required: any depth can be specified. Short series suitable for column bases. Long series suitable for vessel bases or skid-mounted units.
4
F Square
H 4D 2D
Dimensions in millimetres
Bolt Type J8 J 10 J 12 J 16 J 20 J 24 J 30 D Dia 8 10 12 16 20 24 30 H Min 175 230 280 395 480 575 740 P Max 70 80 90 110 120 140 160 L Length 245 310 370 505 600 715 900 C Thread 40 50 60 60 70 80 80 Pocket W 50 50 60 60 70 80 80 X 60 80 100 130 160 190 240
The economy of the design in terms of meeting performance criteria is of course an overall important consideration: MAINEPORT LTD anchor bolts will form an integral part of the most economic design solution.
Bolt Diameter
The bolt diameter is normally determined from the loadings imposed by the structure supported. Reference should be made to recognised standards e.g. BS 5950 for further information and guidance.
Bolt Length
The embedded length of the sleeve and the anchor bolt is normally determined by the properties of the concrete into which it is cast, and the bolt loading. The MAINEPORT LTD standard anchor bolts are designed to transmit the full tensile load specified in BS 4190 (Gr 4.6) in accordance with BS 5950, assuming a grade C30 concrete to BS 8110.
Corrosion
Positive means of minimising corrosion should be specified, and corrosion allowances not relied upon to achieve the design life. Bolt sleeves and pockets should be filled with a suitable inert material, and sealed to prevent moisture ingress.
Packing
Packing shim and location details should be specified if they form part of the permanent design solution.
Grouting
Grouting details should be specified on the construction drawing. Adequate access for bedding and filling of materials should be provided.
Standard Specification
All dimensions are in millimetres. Threads: ISO metric to BS 3643 coarse series, free fit class 7H/8G. Minimum length 3 x bolt dia. Bolts 72mm dia. and above: ISO Metric Fine Series medium fit, class 6H/6G. Nuts: Blank hexagon to BS 4190-1967 Strength Grade 4.6. Washers: Black Steel to BS 4320-1968-Metric Series. Sleeves: Pipe to BS 1387 (medium) or rolled steel sheet to BS 4360 GR 43A. Anchor Plates: Steel to BS 4360 Grade 43A. Identification: Each assembly is individually identified with type reference. Finish: Self colour, with threaded components cleaned and oiled.
Options
High strength materials e.g. BS 4190 Gr 8.8. Anchor plate cap (see Fig. 2a). Alternative thread forms e.g. UNC. Specials: customer-designed single and composite units. Non-standard lengths and projections. Extra nut or locknut.
Outside dia 16 30.0 20 37.0 24 44.0 30 56.0 36 66.0 42 78.0 48 92.0 56 105.0 Dimensions is millimetres
Anchor Plates
10
Ordering Information
Plates Specify anchor plate material, size and thickness; tang detail and corrosion protection for top surface. N.B. Lower surface and tangs should be left to self colour. Order by bolt type and quantity for standard units. Specify: R.C. Floor thickness X Non-standard dimensions if applicable e.g. Projection P. e.g. 3 No. F24X = 180. Order by bolt type and quantity for standard units. Specify: Short or Long Series. Non-standard dimensions if applicable. e.g. 5 No. S 30 L. Order by bolt type and quantity for standard units. Specify: Short or Long Series. Non-standard dimensions if applicable e.g. e.g. SC56 SB = 150. Order by bolt type and quantity for standard units. e.g. 11 No J 12.
Type F
Type S
Type SC
Type J
11