You are on page 1of 390

General Technical Particulars

Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid mm mm mm litres litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

kg kg

Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container plates of individual cells are

kg kg

mm mm sqm

mm mm sqm

mm

mm mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YAP 5
2 Exide Industries Ltd. IS 1652 / BS6290 P16P - HDP n 2Xn

16 16 16 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 2.30 5.25 7.30 8.96 9.60 11.68 12.80 13.57 14.08 14.56 14.93 15.20 15.68 16.00 48

15 - 20 years 6.869

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

3.2 2.25 vpc 2.24 1.12 2.75

10 30

2.3 0.8 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

114*133*260 Depends on the battery layout 123 1.68 n X electrolyte per cell X 1.1

2.7 4.7

n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 106 7.3 0.143 2

Yes, but not recommended

Lead - Antimony alloy grid 119 3.81 0.0181356 3

Yes, but not recommended

PVC 3.43

21 69 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 0.457 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YAP 7
2 Exide Industries Ltd. IS 1652 / BS6290 P24P - HDP n 2Xn

24 24 24 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 3.46 7.87 10.94 13.44 14.40 17.52 19.20 20.35 21.12 21.84 22.39 22.80 23.52 24.00 72

15 - 20 years 4.579

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

4.8 2.25 vpc 3.36 1.68 2.75

15 45

2.3 1.2 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

114*133*260 Depends on the battery layout 123 1.6

n X electrolyte per cell X 1.1

3.5 5.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 106 7.3 0.143 3

Yes, but not recommended

Lead - Antimony alloy grid 119 3.81 0.0181356 4

Yes, but not recommended

PVC 3.43

21

69 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 0.6855 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YAP 9
2 Exide Industries Ltd. IS 1652 / BS6290 P32P - HDP n 2Xn

32 32 32 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 4.61 10.50 14.59 17.92 19.20 23.36 25.60 27.14 28.16 29.12 29.86 30.40 31.36 32.00 96

15 - 20 years 3.425

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

6.4 2.25 vpc 4.48 2.24 2.75

20 60

2.3 1.6 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

114*133*260 Depends on the battery layout 123 1.51

n X electrolyte per cell X 1.1

4.3 6.1 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 106 7.3 0.143 4

Yes, but not recommended

Lead - Antimony alloy grid 119 3.81 0.0181356 5

Yes, but not recommended

PVC 3.43

21

69 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 0.914 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YAP 11
2 Exide Industries Ltd. IS 1652 / BS6290 P40P - HDP n 2Xn

40 40 40 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 5.76 13.12 18.24 22.40 24.00 29.20 32.00 33.92 35.20 36.40 37.32 38.00 39.20 40.00 120

15 - 20 years 2.748

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

8 2.25 vpc 5.6 2.8 2.75

30 90

2.3 2 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

190*133*260 Depends on the battery layout 199 2.86

n X electrolyte per cell X 1.1

5.4 8.8 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 106 7.3 0.143 5

Yes, but not recommended

Lead - Antimony alloy grid 119 3.81 0.0181356 6

Yes, but not recommended

PVC 3.43

21

69 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead 10 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 1.371 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YAP 13
2 Exide Industries Ltd. IS 1652 / BS6290 P48P - HDP n 2Xn

48 48 48 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 6.91 15.74 21.89 26.88 28.80 35.04 38.40 40.70 42.24 43.68 44.78 45.60 47.04 48.00 144

15 - 20 years 2.29

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

9.6 2.25 vpc 6.72 3.36 2.75

40 120

2.3 2.4 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

190*133*260 Depends on the battery layout 199 2.77

n X electrolyte per cell X 1.1

6.2 9.5 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 106 7.3 0.143 6

Yes, but not recommended

Lead - Antimony alloy grid 119 3.81 0.0181356 7

Yes, but not recommended

PVC 3.43

21

69 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead 10 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 1.828 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YAP 15
2 Exide Industries Ltd. IS 1652 / BS6290 P56P - HDP n 2Xn

56 56 56 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 8.06 18.37 25.54 31.36 33.60 40.88 44.80 47.49 49.28 50.96 52.25 53.20 54.88 56.00 168

15 - 20 years 1.963

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

11.2 2.25 vpc 7.84 3.92 2.75

45 135

2.3 2.8 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

190*133*260 Depends on the battery layout 199 2.69

n X electrolyte per cell X 1.1

7 10.2 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 106 7.3 0.143 7

Yes, but not recommended

Lead - Antimony alloy grid 119 3.81 0.0181356 8

Yes, but not recommended

PVC 3.43

21

69 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead 10 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 2.0565 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid

litres

kg kg

Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container

mm

Thickness of Container Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour

mm

mm

Yes/No

m3 Lit

No. of air exchanges required per hour Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve Yes/No Yes/No Volt

YAP 17
2 Exide Industries Ltd. IS 1652 / BS6290 P64P - HDP n 2Xn

64 64 64 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 9.22 20.99 29.18 35.84 38.40 46.72 51.20 54.27 56.32 58.24 59.71 60.80 62.72 64.00 192

15 - 20 years 1.717

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

12.8 2.25 vpc 8.96 4.48 2.75

50 150

2.3 3.2 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

190*133*260 Depends on the battery layout 199 2.69

n X electrolyte per cell X 1.1

7.8 11

n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 106 7.3 0.143 8

Yes, but not recommended

Lead - Antimony alloy grid 119 3.81 0.0181356 9

Yes, but not recommended

PVC 3.43

21

69 YES Explosion proof microporous ceramic made

3 Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead 10 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 2.285

Depends on the size of battery room Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 7
2 Exide Industries Ltd. IS 1652 / BS6290 P75P - HDP n 2Xn

75 75 75 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 10.80 24.60 34.20 42.00 45.00 54.75 60.00 63.60 66.00 68.25 69.98 71.25 73.50 75.00 225

15 - 20 years 1.554

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

15 2.25 vpc 10.5 5.25 2.75

60 180

2.3 3.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

173*203*426 Depends on the battery layout 211 6.47

n X electrolyte per cell X 1.1

10.5 18.2 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 3

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 4

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 2.742 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 9
2 Exide Industries Ltd. IS 1652 / BS6290 P100P - HDP n 2Xn

100 100 100 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 14.40 32.80 45.60 56.00 60.00 73.00 80.00 84.80 88.00 91.00 93.30 95.00 98.00 100.00 300

15 - 20 years 1.11

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

20 2.25 vpc 14 7 2.75

80 240

2.3 5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

173*203*426 Depends on the battery layout 211 6.3

n X electrolyte per cell X 1.1

13.5 21 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 4

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 5

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 3.656 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 11
2 Exide Industries Ltd. IS 1652 / BS6290 P125P - HDP n 2Xn

125 125 125 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 18.00 41.00 57.00 70.00 75.00 91.25 100.00 106.00 110.00 113.75 116.63 118.75 122.50 125.00 375

15 - 20 years 1.05

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

25 2.25 vpc 17.5 8.75 2.75

100 300

2.3 6.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

173*203*426 Depends on the battery layout 211 5.8

n X electrolyte per cell X 1.1

15.5 22.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 5

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 6

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 4.57 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 13
2 Exide Industries Ltd. IS 1652 / BS6290 P150P - HDP n 2Xn

150 150 150 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 21.60 49.20 68.40 84.00 90.00 109.50 120.00 127.20 132.00 136.50 139.95 142.50 147.00 150.00 450

15 - 20 years 0.91

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

30 2.25 vpc 21 10.5 2.75

125 375

2.3 7.5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

173*203*426 Depends on the battery layout 211 5.38

n X electrolyte per cell X 1.1

18 24.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 6

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 7

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 5.7125 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 15
2 Exide Industries Ltd. IS 1652 / BS6290 P175P - HDP n 2Xn

175 175 175 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 25.20 57.40 79.80 98.00 105.00 127.75 140.00 148.40 154.00 159.25 163.28 166.25 171.50 175.00 525

15 - 20 years 0.78

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

35 2.25 vpc 24.5 12.25 2.75

140 420

2.3 8.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

210*203*423 Depends on the battery layout 211 7.56

n X electrolyte per cell X 1.1

19.7 28.7 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 7

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 8

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 6.398 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 17
2 Exide Industries Ltd. IS 1652 / BS6290 P200P - HDP n 2Xn

200 200 200 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 28.80 65.60 91.20 112.00 120.00 146.00 160.00 169.60 176.00 182.00 186.60 190.00 196.00 200.00 600

15 - 20 years 0.76

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

40 2.25 vpc 28 14 2.75

160 480

2.3 10 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

210*203*423 Depends on the battery layout 211 7.31

n X electrolyte per cell X 1.1

22 30.7 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 8

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 9

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 7.312 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 19
2 Exide Industries Ltd. IS 1652 / BS6290 P225P - HDP n 2Xn

225 225 225 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 32.40 73.80 102.60 126.00 135.00 164.25 180.00 190.80 198.00 204.75 209.93 213.75 220.50 225.00 675

15 - 20 years 0.68

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

45 2.25 vpc 31.5 15.75 2.75

180 540

2.3 11.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

248*203*423 Depends on the battery layout 211 8.91

n X electrolyte per cell X 1.1

24.3 24.9 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 9

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 10

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 8.226 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 21
2 Exide Industries Ltd. IS 1652 / BS6290 P250P - HDP n 2Xn

250 250 250 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 36.00 82.00 114.00 140.00 150.00 182.50 200.00 212.00 220.00 227.50 233.25 237.50 245.00 250.00 750

15 - 20 years 0.65

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

50 2.25 vpc 35 17.5 2.75

200 600

2.3 12.5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

248*203*423 Depends on the battery layout 211 8.57

n X electrolyte per cell X 1.1

26.7 36.9 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 10

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 11

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 9.14 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 23
2 Exide Industries Ltd. IS 1652 / BS6290 P275P - HDP n 2Xn

275 275 275 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 39.60 90.20 125.40 154.00 165.00 200.75 220.00 233.20 242.00 250.25 256.58 261.25 269.50 275.00 825

15 - 20 years 0.59

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

55 2.25 vpc 38.5 19.25 2.75

220 660

2.3 13.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

286*203*423 Depends on the battery layout 211 10.34

n X electrolyte per cell X 1.1

29.1 41.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 11

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 12

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 10.054 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 25
2 Exide Industries Ltd. IS 1652 / BS6290 P300P - HDP n 2Xn

300 300 300 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 43.20 98.40 136.80 168.00 180.00 219.00 240.00 254.40 264.00 273.00 279.90 285.00 294.00 300.00 900

15 - 20 years 0.52

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

60 2.25 vpc 42 21 2.75

240 720

2.3 15 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

286*203*423 Depends on the battery layout 211 10

n X electrolyte per cell X 1.1

31.5 43.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 12

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 13

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 10.968 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 27
2 Exide Industries Ltd. IS 1652 / BS6290 P325P - HDP n 2Xn

325 325 325 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 46.80 106.60 148.20 182.00 195.00 237.25 260.00 275.60 286.00 295.75 303.23 308.75 318.50 325.00 975

15 - 20 years 0.48

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

65 2.25 vpc 45.5 22.75 2.75

260 780

2.3 16.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

362*203*423 Depends on the battery layout 211 13.7

n X electrolyte per cell X 1.1

36.3 52.6 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 13

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 14

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 11.882 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 29
2 Exide Industries Ltd. IS 1652 / BS6290 P350P - HDP n 2Xn

350 350 350 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 50.40 114.80 159.60 196.00 210.00 255.50 280.00 296.80 308.00 318.50 326.55 332.50 343.00 350.00 1050

15 - 20 years 0.44

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

70 2.25 vpc 49 24.5 2.75

280 840

2.3 17.5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

362*203*423 Depends on the battery layout 211 13.36

n X electrolyte per cell X 1.1

38.5 54.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 14

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 15

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 12.796 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 31
2 Exide Industries Ltd. IS 1652 / BS6290 P375P - HDP n 2Xn

375 375 375 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 54.00 123.00 171.00 210.00 225.00 273.75 300.00 318.00 330.00 341.25 349.88 356.25 367.50 375.00 1125

15 - 20 years 0.42

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

75 2.25 vpc 52.5 26.25 2.75

300 900

2.3 18.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

362*203*423 Depends on the battery layout 211 13.11

n X electrolyte per cell X 1.1

40.8 56.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 15

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 16

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 13.71 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YKP 33
2 Exide Industries Ltd. IS 1652 / BS6290 P400P - HDP n 2Xn

400 400 400 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 57.60 131.20 182.40 224.00 240.00 292.00 320.00 339.20 352.00 364.00 373.20 380.00 392.00 400.00 1200

15 - 20 years 0.38

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

80 2.25 vpc 56 28 2.75

320 960

2.3 20 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

362*203*423 Depends on the battery layout 211 12.77

n X electrolyte per cell X 1.1

43.2 58.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 16

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 17

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 14.624 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid

litres

kg

with acid Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg kg kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs

mm

Explosion proof microporous ceramic made

Container Thickness of Container Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms m3 Yes/No mm mm

Gas generation per single cell per hour No. of air exchanges required per hour Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Lit

Yes/No Volt

Yes/No

YKP 35
2 Exide Industries Ltd. IS 1652 / BS6290 P425P - HDP n 2Xn

425 425 425 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 61.20 139.40 193.80 238.00 255.00 310.25 340.00 360.40 374.00 386.75 396.53 403.75 416.50 425.00 1275

15 - 20 years 0.36

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

85 2.25 vpc 59.5 29.75 2.75

340 1020

2.3 21.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

362*203*423 Depends on the battery layout 211 12.44

n X electrolyte per cell X 1.1

45.6

60.4 n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 207 7.8 0.393 17

Yes, but not recommended

Lead - Antimony alloy grid 211 3.81 0.05 18

Yes, but not recommended

PVC 3.2

35

89 YES Explosion proof microporous ceramic made

4 Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 2 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer

15.538 Depends on the size of battery room Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 11
2 Exide Industries Ltd. IS 1652 / BS6290 P535P - HDP n 2Xn

535 535 535 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 77.04 175.48 243.96 299.60 321.00 390.55 428.00 453.68 470.80 486.85 499.16 508.25 524.30 535.00 1605

15 - 20 years 0.332

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

107 2.25 vpc 74.9 37.45 2.75

300 600

2.3 26.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

230*368*682 Depends on the battery layout 238 27.23

n X electrolyte per cell X 1.1

64.3 96.7 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 5

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 6

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 13.71 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 13
2 Exide Industries Ltd. IS 1652 / BS6290 P645P - HDP n 2Xn

645 645 645 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 92.88 211.56 294.12 361.20 387.00 470.85 516.00 546.96 567.60 586.95 601.79 612.75 632.10 645.00 1935

15 - 20 years 0.277

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

129 2.25 vpc 90.3 45.15 2.75

360 720

2.3 32.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

230*368*682 Depends on the battery layout 238 27.23

n X electrolyte per cell X 1.1

64.3 96.7 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 6

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 7

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 16.452 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 15
2 Exide Industries Ltd. IS 1652 / BS6290 P750P - HDP n 2Xn

750 750 750 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 108.00 246.00 342.00 420.00 450.00 547.50 600.00 636.00 660.00 682.50 699.75 712.50 735.00 750.00 2250

15 - 20 years 0.237

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

150 2.25 vpc 105 52.5 2.75

420 840

2.3 37.5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 64.54

n X electrolyte per cell X 1.1

93.8 170.6 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 7

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 8

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 19.194 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 17
2 Exide Industries Ltd. IS 1652 / BS6290 P860P - HDP n 2Xn

860 860 860 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 123.84 282.08 392.16 481.60 516.00 627.80 688.00 729.28 756.80 782.60 802.38 817.00 842.80 860.00 2580

15 - 20 years 0.207

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

172 2.25 vpc 120.4 60.2 2.75

480 960

2.3 43 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 63.36

n X electrolyte per cell X 1.1

104.1 179.5 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 8

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 9

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 21.936 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 19
2 Exide Industries Ltd. IS 1652 / BS6290 P965P - HDP n 2Xn

965 965 965 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 138.96 316.52 440.04 540.40 579.00 704.45 772.00 818.32 849.20 878.15 900.35 916.75 945.70 965.00 2895

15 - 20 years 0.184

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

193 2.25 vpc 135.1 67.55 2.75

550 1100

2.3 48.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 62.02

n X electrolyte per cell X 1.1

114.4 188.2 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 9

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 10

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 25.135 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 21
2 Exide Industries Ltd. IS 1652 / BS6290 P1070P - HDP n 2Xn

1070 1070 1070 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 154.08 350.96 487.92 599.20 642.00 781.10 856.00 907.36 941.60 973.70 998.31 1016.50 1048.60 1070.00 3210

15 - 20 years 0.166

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

214 2.25 vpc 149.8 74.9 2.75

600 1200

2.3 53.5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 60.67

n X electrolyte per cell X 1.1

124.7 196.9 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 10

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 11

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 27.42 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 23
2 Exide Industries Ltd. IS 1652 / BS6290 P1180P - HDP n 2Xn

1180 1180 1180 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 169.92 387.04 538.08 660.80 708.00 861.40 944.00 1000.64 1038.40 1073.80 1100.94 1121.00 1156.40 1180.00 3540

15 - 20 years 0.153

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

236 2.25 vpc 165.2 82.6 2.75

660 1320

2.3 59 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 59.41

n X electrolyte per cell X 1.1

135 205.7 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 11

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 12

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 30.162 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 25
2 Exide Industries Ltd. IS 1652 / BS6290 P1285P - HDP n 2Xn

1285 1285 1285 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 185.04 421.48 585.96 719.60 771.00 938.05 1028.00 1089.68 1130.80 1169.35 1198.91 1220.75 1259.30 1285.00 3855

15 - 20 years 0.138

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

257 2.25 vpc 179.9 89.95 2.75

720 1440

2.3 64.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 58.07

n X electrolyte per cell X 1.1

145.3 214.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 12

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 13

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 32.904 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 27
2 Exide Industries Ltd. IS 1652 / BS6290 P1395P - HDP n 2Xn

1395 1395 1395 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 200.88 457.56 636.12 781.20 837.00 1018.35 1116.00 1182.96 1227.60 1269.45 1301.54 1325.25 1367.10 1395.00 4185

15 - 20 years 0.128

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

279 2.25 vpc 195.3 97.65 2.75

780 1560

2.3 69.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 54.79

n X electrolyte per cell X 1.1

155.6 220.8 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 13

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 14

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 35.646 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 29
2 Exide Industries Ltd. IS 1652 / BS6290 P1500P - HDP n 2Xn

1500 1500 1500 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 216.00 492.00 684.00 840.00 900.00 1095.00 1200.00 1272.00 1320.00 1365.00 1399.50 1425.00 1470.00 1500.00 4500

15 - 20 years 0.119

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

300 2.25 vpc 210 105 2.75

850 1700

2.3 75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 53.53

n X electrolyte per cell X 1.1

165.9 229.6 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 14

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 15

Yes, but not recommended

PVC 4.5

57

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 38.845 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres mm mm mm %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte per Cell

litres

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator plates of individual cells are

litres

kg kg kg kg

mm mm sqm

mm mm sqm

mm

CIearance between bottom of the plate and the bottom of the container

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells

mm

mm

mm

Yes/No

b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve Yes/No Yes/No Volt m3 Lit

YHP 31
2 Exide Industries Ltd. IS 1652 / BS6290 P1605P - HDP n 2Xn

1605 1605 1605 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 231.12 526.44 731.88 898.80 963.00 1171.65 1284.00 1361.04 1412.40 1460.55 1497.47 1524.75 1572.90 1605.00 4815

15 - 20 years 0.111

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

321 2.25 vpc 224.7 112.35 2.75

900 1800

2.3 80.25 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376

66.64

n X electrolyte per cell X 1.1

181.7 261 n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 15

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 16

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

7 Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes

Yes

No Yes

To be provided by customer 41.13 Depends on the size of battery room Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres mm mm mm %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte per Cell

litres

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator plates of individual cells are

litres

kg kg kg kg

mm mm sqm

mm mm sqm

mm

CIearance between bottom of the plate and the bottom of the container

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells

mm

mm

mm

Yes/No

b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve Yes/No Yes/No Volt m3 Lit

YHP 33
2 Exide Industries Ltd. IS 1652 / BS6290 P1715P - HDP n 2Xn

1715 1715 1715 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 246.96 562.52 782.04 960.40 1029.00 1251.95 1372.00 1454.32 1509.20 1560.65 1600.10 1629.25 1680.70 1715.00 5145

15 - 20 years 0.104

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

343 2.25 vpc 240.1 120.05 2.75

960 1920

2.3 85.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376

65.21

n X electrolyte per cell X 1.1

192 269.6 n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 16

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 17

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

7 Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes

Yes

No Yes

To be provided by customer 43.872 Depends on the size of battery room Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres mm mm mm %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte per Cell

litres

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator plates of individual cells are

litres

kg kg kg kg

mm mm sqm

mm mm sqm

mm

CIearance between bottom of the plate and the bottom of the container

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells

mm

mm

mm

Yes/No

b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve Yes/No Yes/No Volt m3 Lit

YHP 35
2 Exide Industries Ltd. IS 1652 / BS6290 P1820P - HDP n 2Xn

1820 1820 1820 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 262.08 596.96 829.92 1019.20 1092.00 1328.60 1456.00 1543.36 1601.60 1656.20 1698.06 1729.00 1783.60 1820.00 5460

15 - 20 years 0.098

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

364 2.25 vpc 254.8 127.4 2.75

1025 2050

2.3 91 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376

63.87

n X electrolyte per cell X 1.1

202.3 278.3 n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 17

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 18

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

7 Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 3 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes

Yes

No Yes

To be provided by customer 46.8425 Depends on the size of battery room Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres mm mm mm %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte per Cell

litres

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator plates of individual cells are

litres

kg kg kg kg

mm mm sqm

mm mm sqm

mm

CIearance between bottom of the plate and the bottom of the container

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells

mm

mm

mm

Yes/No

b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve Yes/No Yes/No Volt m3 Lit

YHP 37
2 Exide Industries Ltd. IS 1652 / BS6290 P1930P - HDP n 2Xn

1930 1930 1930 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 277.92 633.04 880.08 1080.80 1158.00 1408.90 1544.00 1636.64 1698.40 1756.30 1800.69 1833.50 1891.40 1930.00 5790

15 - 20 years 0.092

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

386 2.25 vpc 270.2 135.1 2.75

1100 2200

2.3 96.5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376

76.81

n X electrolyte per cell X 1.1

215.9 307.3 n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 18

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 19

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

7 Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes

Yes

No Yes

To be provided by customer 50.27 Depends on the size of battery room Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 39
2 Exide Industries Ltd. IS 1652 / BS6290 P2035P - HDP n 2Xn

2035 2035 2035 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 293.04 667.48 927.96 1139.60 1221.00 1485.55 1628.00 1725.68 1790.80 1851.85 1898.66 1933.25 1994.30 2035.00 6105

15 - 20 years 0.087

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

407 2.25 vpc 284.9 142.45 2.75

1150 2300

2.3 101.75 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 75.46

n X electrolyte per cell X 1.1

225.9 315.7 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 19

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 20

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 52.555 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid with acid Complete Battery without acid

litres

kg kg kg

with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs Container Thickness of Container

mm

mm

Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms Gas generation per single cell per hour No. of air exchanges required per hour m3 Lit Yes/No mm

Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Yes/No Volt

Yes/No

YHP 41
2 Exide Industries Ltd. IS 1652 / BS6290 P2140P - HDP n 2Xn

2140 2140 2140 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 308.16 701.92 975.84 1198.40 1284.00 1562.20 1712.00 1814.72 1883.20 1947.40 1996.62 2033.00 2097.20 2140.00 6420

15 - 20 years 0.083

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

428 2.25 vpc 299.6 149.8 2.75

1200 2400

2.3 107 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 74.12

n X electrolyte per cell X 1.1

236.2 324.4 n X each cell weight without acid

n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 20

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 21

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer 54.84 Depends on the size of battery room

Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

General Technical Particulars


Units Type of Cell Nominal Voltage per cell Manufacturer's Name Standards to which battery is manufactured IS Nomenclature Number of cells in the battery bank Nominal Voltage of Battery Declared Capacity at 27 degree C upto 1.85 ecv Initial Rated End of Life Rated Capacity at mimimum ambient temperature Rated Capacity at maximum ambient temperature Capacity in AH at various end cell voltages and duration of discharge 5 minutes 15 minutes 30 minutes 45 minutes 1 hour 2 hour 3 hour 4 hour 5 hour 6 hour 7 hour 8 hour 9 hour 10 Hour Maximum momentary current for 1 min till 1.60 e.c.v Expected life of battery under normal operation & maintainence conditions Internal Resistance of cell (IR) E.C.V. 1.62 1.65 1.69 1.71 1.75 1.78 1.80 1.81 1.82 1.83 1.83 1.84 1.84 1.85 Volts Volts

AH AH AH Ah Ah

Years milli ohms

Total Resistance of Battery

Ohms Loss in capacity in 21 hours due to self discharge Recommended Charging rate for a) Float Charging i) Limit current ii) Voltage b) Boost charging i) Starting Current ii) Finishing current iii) Voltage Trickle Charging Rate i) Minimum ii) Maximum Equalising charge a) Voltage b) Current c) Duration d) Interval between succesive equalising charge Recommended Specific gravity at 27 deg C a) for first filling b) at full charge c) when Battery is discharged at 10 hours rate Permissible max. temperature of Electrolyte i) During Initial Charging ii) During Normal Operation Overall dimensions Each Cell L x W x H (tolerance of +/- 2 mm in each case) Complete Battery Distance between cell centres Quantity of Electrolyte per Cell mm mm mm litres %

A V A A V

mA mA

V A Hrs. Months

deg C deg C

Quantity of Electrolyte for battery (Including 10% extra) Weight(+/-5%) Each cell without acid

litres

kg

with acid Complete Battery without acid with acid Material and type of Plates i) Positive Plates Material Height of Positive Plate Thickness of Positive Plate Area of Positive Plate No. of positive plates per cell Whether positive interchangeable ii) Negative Plates Material Height of Negative Plate Thickness of Negative Plate Area of Negative Plate No. of negative plates per cell Whether negative plates of individual cells are interchangeable Material and type of Separators Material Thickness of separator CIearance between bottom of the plate and the bottom of the container plates of individual cells are

kg kg kg

mm mm sqm

mm mm sqm

mm

mm

Clearance between top of the plates and top of container Whether explosion vents are offerred Type of Vent and Filling Plugs

mm

Explosion proof microporous ceramic made

Container Thickness of Container Material of Container Cover Type of cover Material of Cover Connections Material of Inter-Cell Connectors Thickness of Inter-Cell Connectors Method of connection Inter-row, Inter-tier connectors and end take-offs furnished? Connection hardware with 5% extra furnished? Material of Bolt, Nut and Washer for Inter-Cell and Cable Connections Cell insulators provided If yes, material of insulator Racks Racks a) Number of racks per battery b) Number of cells per rack c) Type of racks d) Material of rack e) Dimensions of the racks Racks provided with a) Numbering tags for cells b) Insulators Insulator with 5% extra furnished for a) Cell b) Stand Ventilation requirements Cubic content of battery rooms m3 Yes/No mm mm

Gas generation per single cell per hour No. of air exchanges required per hour Standard Maintenance accessories provided Gasification Voltage per Cell Characteristic Curves (furnish curve numbers and attach separate sheet) i) Charge Hours Vs Volts during Boost mode ii) Discharge hours Vs AH in percent of 10 Hrs Discharge rate (Capacities at various discharge rates) iii) Capacity Vs Ambient temperature iv) Discharge Rate Vs minimum Discharge Voltage Recommended Max. period of cell storage before the first Charge (After Installation and filling of Electrolyte) Recommended Storage life of Battery (Dry shelf life) Does the battery meet the required duty cycle curve

Lit

Yes/No Volt

Yes/No

YHP 43
2 Exide Industries Ltd. IS 1652 / BS6290 P2250P - HDP n 2Xn

2250 2250 2250 As per formula: Ct=C27{1+0.009(t-27)} As per formula: Ct=C27{1+0.009(t-27)}

Ah output 324.00 738.00 1026.00 1260.00 1350.00 1642.50 1800.00 1908.00 1980.00 2047.50 2099.25 2137.50 2205.00 2250.00 6750

15 - 20 years 0.079

I.R x no.of cells +0.1 ohms upto 30 cells or+0.2 ohms upto 54 cells or+0.3 ohms above 54 cells <8%

450 2.25 vpc 315 157.5 2.75

1250 2500

2.3 112.5 6 6

1.190 +/- 0.005 1.200 +/- 0.005 1.120 - 1.130

50 45

433*368*682 Depends on the battery layout 376 72.69

n X electrolyte per cell X 1.1

246.6

333.1 n X each cell weight without acid n X each cell weight with acid

99.99% Pure Lead 368 9.8 1.12608 21

Yes, but not recommended

Lead - Antimony alloy grid 378.5 5.08 0.19 22

Yes, but not recommended

PVC 4.5

51

140.5 YES Explosion proof microporous ceramic made

7 Transperant Styrene Acrylonitrile (SAN)

Adhesive Sealed Opaque Styrene Acrylonitrile (SAN)

Lead Plated Copper 6.5 Bolted

Yes Yes

Lead plated MS No

Depends on the battery layout Depends on the battery layout Depends on the battery layout Sal wood Depends on the battery layout

Yes Yes

No Yes

To be provided by customer

57.125 Depends on the size of battery room Yes 2.36

Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue Yes ; As per catalogue

12 - 18 hours

Yes

You might also like