Professional Documents
Culture Documents
Q7T3 FP737 LCD Monitor Service Guide
Q7T3 FP737 LCD Monitor Service Guide
B. Timing adjustment: 1. Enter factory setting area (press ENTER, EXIT and then press SOFTPOWER). 2. Check the settings to following values: Contrast = 50 Brightness = 90 Volume = 30 OSD time = 20 Color = sRGB Language = English Then, turn off the monitor power. 3. Turn on power enter user area. C. Color balance adjustment: 1. Enter factory setting area (press ENTER, EXIT and then press SOFTPOWER). 2. Setup input timing ICL-605 (1280*1024 75Hz), 5-MOSAIC pattern.(timing 202 pattern 42) 3. PressI-key,to enter window for whitebalance and burning mode. 4. Press Whitebalance, to Calibrate ADC. 5. Setup input timing ICL-605, 32 -Gray pattern. 6. Checking if the picture is no good, reject this monitor. D. Color adjustment: 1. Setup input timing ICL-605, white pattern. 2. Measure color temperature by Minolta CA-110 (or equivalent equipment). 3. Alignment the color temperature Bluish, Reddish & sRGB. The color temperature specification as follows: White Balance (Bluish, 9300K set on OSD) White Balance (Reddish, 5800K set on OSD) White Balance (sRGB, 6500K set on OSD) X+Y+X+Y+X+Y+0.283+(-) 0.03 0.297+(-) 0.03 0. 326+(-) 0.03 0. 342+(-) 0.03 0. 313+(-) 0.03 0. 329 +(-) 0.03
1 Confidential
2 Confidential
checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum
Note A: Byte4(Checksum) = Byte1 + Byte2 + Byte3 Note B: Data = The value write to MCU Note C: XX = don't care, any value(<=0xFF). Note D: The Byte-2 definition of Change Language Setting is as below, 0=DE, 1=EN, 2=ES, 3=FR, 4=IT, 5=JA, 6=, 7= When PC Host sends 0x7D command to MCU, MCU must return as following (2 bytes) Return Code Checksum error code Normal return code If normal return code is exact FCh R-Byte1 FC the above Byte3 (/data) FC R-Byte2 AA FC CF
The Table is for alignment machine to read data from EEPROM to check if the alignment process and write data are correct.
4 Confidential
Additional define for OEM model, for reference only. Write sRGB Contrast CA 53 Write sRGB Brightness CA 54 Write Serial number byte 0~9 AA 0~9 Read Serial number byte 0~9 A3 0~9
Data Data XX XX
Table 1.
Remark
DOS VESA VESA VESA
135.00 135.09
VESA SUN
5 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Alignment Procedure 2. Dressing
A. Check the 4 springs and 5 spacers on the BKT
6 Confidential
7 Confidential
8 Confidential
9 Confidential
10 Confidential
11 Confidential
12 Confidential
13 Confidential
14 Confidential
15 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
I. Introduction:
The Q7T3-FP731-D is a 17 SXGA (1280x1024) , 262 K colors(R, G, B 6-bit data) TFT LCD monitor with multi-media function. Its an Dual (analog and digital) interface LCD monitor with a 15 pins D-sub signal cable and a 24pins DVI-D cable . its compliant with VESA specification to offer a smart power management and power saving function. It also offers OSD menu for users to control the adjustable items and get some information about this monitor, and the best function is to offer users an easy method to set all adjustable items well just by pressing one key, we called it Auto key which can auto adjusting all controlled items. Q7T3-FP731-D also offer DDC2 function to meet VESA standard.
D-Sub AC power in
DVI-D
III. Circuit operation theory: A.) HEAD: A-1.) Interface board diagram:
1 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
D-SUB
MTV312M 64(AJ)
Clock Generator
DVI-D
XGA
Mst 8131B
12801024 LCM
IIC
Keypad
2 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
(a) Circuit operation theory: A basic operation theory for the interface board is to convert input signal into digital RGB . Analog RGB signal is converted to digital signal through ADC. DVI-D signal is converted through TMDS receiver. The microprocessor Mst8131B receives video data and optimizes the image automatically. It also supports input source selection, 16 color from a 64k palette bitmap OSD, and keypad controlling. The output data are sent to LCD module. (b) IC introduction:
1.) DDC (Display Data Channel) function: We use DDC IC to support DDC/2B function. DDC data is stored in 24C04(EEPROM). Those data related to LCD monitor specification. SDA and SCL serial communication for I2C communication for DDC2B. PC can read them by
2.) Mst8131B IC: There are A/D, Scaling, OSD, MCU functions in the Mst8131B IC. Scaling IC is revolutionary scaling engine, capable of expanding any source resolution to a highly uniform and sharp image, combined with the critically proven integrated 8 bit triple-ADC and patented Rapid-lock digital clock recovery system. It also support detect mode and DPMS control. MCU control unit, it controls all the functions of this interface board, just like the OSD display setting, the adjustable items, adjusted data storage, the external IIC communication, support DDC2B. 3.) EEPROM: We use 24C04 to store all the adjustable data and user settings. And use 24C02 to store DVI EDID data. 4.) MTV312M64: To stored the source code which is accessed by MCU to run program.
3 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
A-2.) Power board diagram:
EMI Filter
Inverter circuit
PWM controller
Switching element
Feedback Isolation
Fig.1
#1 EMI Filter
This circuit (fig. 2) is designed to inhibit electrical and magnetic interference for meeting FCC, VDE, VCCI standard requirements.
Fig. 2
4 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory #2 Rectifier and filter
AC Voltage (90-264V) is rectified and filtered by BD601, C605 (See Fig 3) and the DC Output voltage is 1.4*(AC input). (See Fig.3)
Fig. 3
5 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory #3 Switching element and Isolation power transformer
When the Q601 turns on, energy is stored in the transformer. During Q601 turn-off period, the stored energy is delivered to the secondary of transformer. R607, C607 and D601 is a snubber circuit. R615 is current sense resistor to control output power. (See Fig.4)
Fig. 5
6 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory #5 PWM Controller
The PWM controller NCP1200A implements a standard current mode architecture. With an internal structure operating at a fixed 40KHz. Where the switch time is dictated by the peak current set-point. When the current set-point falls below a given value. The output power demand diminishes, the IC automatically enters the so-called skip cycle mode and provides excellent efficiency.
Fig. 7
7 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
A-3.) Control board introduction:
The main parts of the control board are a push button, and a LED. (a) Push button: Its a simple switch function, pressing it for ON to do the auto adjustment function, releasing it for OFF to do nothing. (c) LED: It indicates the DPMS status of this LCD monitor; green light means DPMS on (Normal operating condition). Amber light means DPMS off (Power off condition).
8 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
A-4.) Inverter diagram:
1.Block Diagram:
OSCILATOR CIRCUIT
TRANSFORMER
CCFL
ON/OFF
BRT_ADJ
2. General Specification Input Voltage: 15V Input Current: 2A max. ON/OFF Voltage: 3.3V PWM Duty: 3.3V/47KHz Output Requirement: Max. Output Current: 15mA Min. Output Current: 6mA Lamp Working Voltage: 600Vrms Open Lamp Voltage: 1700Vrms Frequency: 50KHz
9 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
3.Circuit Operation Theorem 3.1 ON/OFF SWITCH
The turn-on voltage was controlled by R756 and R757.The inverter was turned on or off by the switching transistors Q761 and Q757, Also regulator IC751 is control by Q761 and Q757 decide supply 15V to inverter part or instead.
10 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
3.2 PWM Control circuit
TL1451 is a dual PWM controller.C765 and R765 decide the working frequency.BLT_ADJ signal is from control board, control pulse width then decide how much energy delivery to CCFL also decide CCFL brightness. Q741 and Q742 be the buffer to rise the drive capability and the totem poles circuit can improve a capable of driving for Q743.C770 decide the striking time delay.
11 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Circuit Operation Theory
3.3 Oscillator Circuit
Royer circuit uses the characteristic of transformer saturation to oscillate. When the DC power inject, Q759 or Q760 will turns on, and the current Ic increases. After a period, the transistor will leave the saturation status and Vce increase. The result causes the voltage of primary coil get lower. Finally the transistor turn off, and another transistor turn on. These statuses are repeated and the pin7 and pin8 of T751 will get a Sin Wave to turn on CCFL.
12 Confidential
2.4 Electrostatic Discharge Requirements.......................................................................................9 2.5 Safety Requirements....................................................................................................................9 2.6 EMI Requirements ......................................................................................................................9 2.7 Reliability......................................................................................................................................9 2.8 Mechanical Design for TCO 03: .................................................................................................9 2.9 Environment Protection Design: ................................................................................................10 2.10 Acoustical Noise .........................................................................................................................10
3.3 Number of display colors: ...........................................................................................................13 3.4 Adjustment function ....................................................................................................................13 3.5 Power Supply Requirements.......................................................................................................13
3.5.1 Input Power Requirements .............................................................................................................................13 3.5.2 Output Power Requirement............................................................................................................................14 3.5.3 Power Management.........................................................................................................................................14
3.6
Specification of Inverter...........................................................................................................14
5. Physical Specifications................................................................................................................18
5.1 Physical Dimension & Appearance ............................................................................................18
5.1.1 Overall Dimensions: .......................................................................................................................................18 5.1.2 Outer Appearance: ..........................................................................................................................................18
5.2 Construction and Materials on outer surface ...........................................................................18 5.3 Base................................................................................................................................................18 5.4 Marking & Labels........................................................................................................................18
5.4.1 Reference Label (Rear panel) ........................................................................................................................18 5.4.2 Controls & Connectors ...................................................................................................................................18
5.5 Packaging......................................................................................................................................18
5.5.1 Carton Dimension: ..........................................................................................................................................18 5.5.2 Shipping Weight:.............................................................................................................................................18 5.5.3 Shipping Container: ........................................................................................................................................18
Table of Contents
6.5 Electrical Emission and Energy Saving summary for TCO 03 ...............................................19
6.5.1 Electrical Field(AC):.......................................................................................................................................19 6.5.2 Magnetic Field(AC): .......................................................................................................................................19 6.5.3 Energy Saving: ................................................................................................................................................19
Appendix 1 Shipment Conditions..................................................................................................20 Fig. 1 Physical Dimension Front View and Side view .................................................................20
3 Confidential
- User controls: (a) (b) (c) (d) (e) (f) Power on/off switch. Exit key( Back to main menus or leave OSD menu and hot key of Input selection). I-key( For auto adjust vertical position, phase, horizontal position and pixel clock ). Enter key(For enter sub-menus or select items.). Left key (Select left, decreasing adjust and hot key of Contrast adjustment). Right key (Select right, increasing adjust and hot key of Brightness adjustment). - OSD window for control and information display with 8 languages selection. - DPMS (Display Power Management System) - Power on/off indicator. - High quality advanced zoom function (Scaling function) - Tilt base : Attached base with 0~25 degree tilt. -DDC2B function supported. - A LCD monitor (a)Head part: (1) A LCD module(LG M170E01-A5NC). (2) An AC power and inverter board. (3) An Interface board. (4) A control board. (5) A signal cable with 15pin D-sub and 24 pin DVI connector . (b) Base part: (1) Tilt base. (2) Foldable - A power cord - An user menu. -Setup disk. (including .INF/.ICM/Test pattern) --all INF/ICM/Test pattern are loaded in CD manual + Quick start guide
4 Confidential
2.1.3 Altitude
-Operating -Storage 0 0 to 3,048m (12,000ft) to 12,192m (40,000ft)
2.2 Transportation
2.2.1 Vibration Test (Package, Non-Operating)
A) Sine-wave vibration for initial resonance sweeps and dwell * Sine sweep Frequency (Hz) 5 ~ 26.6 26.6 ~ 50 50 ~ 500 Status 0.6G 0.016" 1.5G
Sweep times: 1 sweep / Per Axis (X,Y, and Z Axis ) * One major resonance dwell is required for each axis. Total dwell time at each resonance point shall be 15 minutes. B) Random Vibration Frequency (Hz) Slope ( dB/Oct.) Spectrum Level (g2/Hz) 5 ~ 100 100 ~ 200 200 0 -6 --Equivalent to 1.47 G rms * Duration: 30 Minutes / Per Axis (X,Y, and Z Axis ) Total test time : 90 Minutes 0.015 --0.0038
Weight ( Kg ) 09 > 9 - 18.2 > 18.2 - 27.2 > 27.2 - 45.4 > 45.4 - 68.1 > 68.1 113.5
-Corner 5-3-2
select at weakness side [the low left(or right) corner of the front panel] -An edge drop with impact on the shortest edge radiating from corner 5-3-2 -An edge drop with impact on the next shortest edge radiating from corner 5-3-2 -An edge drop with impact on the longest edge radiating from corner 5-3-2 -A flat drop with impact on the rear -A flat drop with impact on the front -A flat drop with impact on the right -A flat drop with impact on the left -A flat drop with impact on the bottom -A flat drop with impact on the top After test, there is no electrical and mechanical damage permitted.
Pallet D
406 1254 115 X X X
(Every container)
with pallet 20' 910
Pallet A: 14 8
Confidential
2. The sample for EMI agency approval should be under 4 dB of the limit. The production pilot run units should be under 3 dB of the limit. The mass production units should be under 1 dB of the limit.
2.7 Reliability
1. The prediction MTBF of display unit shall be greater than 60,000 hours excluding the lamp.(at 25 )
2. Lamp life time : 40,000 hrs typical at which brightness of lamp is 50% compare to that of initial value at 7.0mA and 25. 2.8 Mechanical Design for TCO 03:
1) Front Frame Reflectance: * diffuse reflectance: 10% * Gloss 2% gloss unit 2) Labeling of plastics: 9 Confidential
15pin D-sub female 1 2 3 4 5 6 7 8 9 10 11 12 13 RED VIDEO GREEN VIDEO BLUE VIDEO GROUND Cable Detect RED GROUND GREEN GROUND BLUE GROUND PC5V SYNC GROUND GROUND SDA H SYNC (H+V) 10 Confidential
* 24 pins DVI female Pin 1 2 3 4 5 6 7 8 9 10 11 12 3.1.1.2 Cable length: 1500mm +/20mm Signal Assignment TMDS RX2TMDS RX2+ TMDS Ground Floating Floating DDC Clock DDC Data Floating TMDS RX1TMDS RX1+ TMDS Ground Floating Pin 13 14 15 16 17 18 19 20 21 22 23 24 Signal Assignment Floating +5V Power Ground Hot Plug Detect TMDS RX0TMDS RX0+ TMDS Ground Floating Floating TMDS Ground TMDS Clock+ TMDS Clock-
3.2 Function
3.2.1 Support timing This Interface board is designed to operate in any of the following video mode.
Incoming display mode (Input timing) Resolution 640x350 720x400 Horizontal 31.47(P) 31.47(N) Vertical 70.08(N) 70.08(P) Dot Clock 25.17 28.32 Remark DOS DOS Multi-scan operation Actual display resolution 1280x943 full screen
11 Confidential
Notes (1) If the incoming display mode is not supported by this I/F board listed above, the picture can show up or doesnt which is unpredictable, even the picture can display but probably isnt good or clear. (2) Some signals from graphics board may not function properly. (3) P, N stands for Positive, Negative polarity of incoming HSYNC/VSYNC(input timing). (4) OSD will show No Signal message on the screen as below to indicate it while no display mode inputs. (5) OSD will show No Cable Connection message on the screen as below to indicate it while no cable 12 Confidential
The unit shall meet all the operating requirements with an input voltage range of 90~264 Vac .
(2) Input Current Maximum Input Current (MAX) 2 Arms (3) Frequency Range The unit shall operate within a frequency range of 47Hz to 63Hz. (4) Inrush Current Power supply inrush current shall be less than the ratings of its critical components (including Power switch, fuse, rectifiers and surge limiting device) for all conditions of line voltage. (5) Regulator Efficiency 70% minimum (measuring at 115Vac and full load) Power saving mode 1 Watts at 115vac 13 Confidential Measuring Range 90Vac 264Vac
3.5.3 Power Management Mode Normal off H/Vsync Both exist None or Only one exist Power consumption < 40W < 1W, under 115Vac < 2W, under 264Vac LED Color (Status) Blue (Normal) Amber Recovery Time -< 3 sec
3.6
Specification of Inverter
The backlight system is an edge-lighting type with 4 CCFLs (Cold Cathode Fluorescent Tube). The characters of dual lamps are shown in the following tables.
ITEM
Lamp Voltage Lamp Current Inverter Frequency Starting lamp voltage Lamp life time
SYMBOL
VL
MIN
-2.5 40 1250 1000
TYP
650 6.5 60 ----
MAX
-7 70 ----
Unit
V mA kHz V V Hr
Condition
IL=6.5 mA Each Lamp Tb=0 oC Ta=25oC Ta=252 oC
IL
FL VS LT
50,000
NOTE:
1.All condition are at 25C ambient unless otherwise specified. 2. Load Panel=SXGA 17
14 Confidential
15 Confidential
= 90 , Up x = 0 , Right
= 270 , Down
4. Response time TrR measures the transition time of L1 relative luminance from white to black state, from 90% to 10% (see graph below) TrD measures the transition time of L1 relative luminance from black to white state, from 10% to 90% (see graph
WHITE BLACK WHITE
100% 90%
16 Confidential
l LA-LA l / LA x 100%= 1.2% max., LA and LB are brightness at location A and B l LB-LB l / LB x 100%= 1.2% max., LA and LB are brightness at location A and B LALuminance of measured point in A (cd/m2) LBLuminance of measured point in B (cd/m2) LALuminance of measured point in A (cd/m2) LBLuminance of measured point in B (cd/m2) (at Viewing Angle = 0 , = 0 )
o
90%
50%
10%
Brightness Uniformity
Min. brightness
/ Max. brightness
4. Functional specification
All the tests to verify specifications in this section must be performed under the following standard conditions unless otherwise noted. The standard conditions are: -Temperature : 0 to 40 degree Celsius -AC line input voltage : 90 Vac to 264 Vac, 47Hz or 63Hz -Warm-up time : 30 minutes minimum
5. Physical Specifications
5.1 Physical Dimension & Appearance
5.1.1 Overall Dimensions:
375mm (W) X 370mm (H) X 155mm (D)
5.3 Base
(1)Tilt: fiest hinge:0~ 25
5.5 Packaging
5.5.1 Carton Dimension:
456mm (W) X395mm (D) X 146mm (H) (LCD monitor)
18 Confidential
6.3 Accessibility
6.3.1 General:
All panels, covers, and major assemblies are removable without disruption of permanent mounting or fasteners.
6.4.2 Documentation
in A service manual will be available which covers all service requirements. A users manual written Japanese German, Italian, Spanish, France and English will be available to ship with the product.
ITEM Power Brightness Contrast OSD- Timeout OSD-Language OSD-Image size OSD-Color temp
Fig. 1
20 Confidential
Power off No
Yes
Turn on power
No
No
Check Power BD
No
Check control BD
No
No
No
Replace interface BD
Replace panel
1 Confidential
Is control BD connecting?
No
Yes
Yes
No Check Interface BD
2 Confidential
Is control BD working?
No
Replace control BD
Check interface BD
3 Confidential
Y Check IC751
Y IC751 PIN 9 IS 1416V? N LED shined? N Y PWM existed? (BLT_ADJ) Y 3.3V existed? Y Replace new fuse Turn on level existed? (BLT_ON) Y N IS I/F board connected? N
N Insert them again Check CN752, CN753 was pluged properly? Y N Replace IC751,Q751 Checking F601 Broke? N Check IC701 OK?
Replace IC701
4 Confidential
Power off No
Yes
Turn on power
No
No
Check Power BD
No
Check control BD
No
No
No
Replace DVI BD
Replace panel
5 Confidential
Q7T3(AUO Panel) LCD Monitor Service Guide Alignment Procedure 1.Alignment procedure (for function adjustment)
A. Preparation: 1. 2. Setup input timing VGA_60Hz, Cross-Hatch (General-1) pattern. The monitor power on at first time that will enter Factory OSD mode. (If not, Please press Menu and Exit plus Power buttons at the same time. A Factory word will be showed on the upper left hand side of OSD Main menu.) Burn in mode have already started. (See Fig 1.). If it hasnt started, Please choose BURN IN MODE tag and select On to enable burn-in mode. Setup unit and keep it warm up at least 30 minutes
3.
B. Timing adjustment: 1. Enter factory setting area (if it isnt at factory mode, Please press Menu and Exit plus Power buttons at the same time to enter factory mode.). 2. Burn-In Mode off. See Fig 2. 3. Select timing from Table 1. The timing marked with star sign (*) have to be adjusted. 4. Execute Recall All (press Yes) to clear user area in EEPROM 5. The cursor moves to AUTO Adjust or press I-Key to run AUTO adjustment function. 6. Check the phase of the image; if phase is not perfect adjust it to the best condition. 7. Adjust the settings to following values: CONTRAST = 50 BRIGHTNESS = 90 OSD TIME = 20 COLOR = sRGB 8. When Factory mode is disable (burn-in mode off) then power off after power on will enter user mode. C. Color balance adjustment: 1. 2. Setup input timing VGA_60Hz, cross-hatch (General-1) pattern. Enter factory setting area (if it isnt at factory mode, Please press Menu and Exit plus Power buttons at the same time to enter factory mode.). 3. 4. 5. 6. 1. 2. Setup the Burn-in mode is On Select the color to user-preset mode. At Main menu move cursor to AUTO Adjust tag then press the ENTER or I-Key to run AUTO Color balance function. Checking if the picture is no good, reject this monitor. Setup input timing VGA_60Hz, cross-hatch (General-1) pattern. Enter factory setting area (if it isnt at factory mode, Please press Menu and Exit plus Power buttons at the same time to enter factory mode.). 3. 4. 5. Move cursor into BUR-IN MODE tag and select On to enable burn-in mode. (If it wants to do Auto Color balance, please select the color to user-preset mode.) Measure color temperature by Minolta CA-110 (or equivalent equipment). The monitor has already set default value to monitor (just for 56.91L53.001) If it cant meet color temperature spec. upper default value. Please use Auto Alignment to calibrate the color temperature; Bluish, & Reddish and sRGB. The color temperature specification as follows: D. Color adjustment:
Move cursor into BURN IN MODE tag and select Off to disable burn-in mode. Turns off the monitor power.
E. Writing EDID file : 1. 2. 3. 4. Setup a PC with DDC card. Connect PC to monitor with a D-sub signal cable. Please refer to the C212 for the correct EDID file. Runs the writing program to write the EDID file into EEPROM for analog input, ie. 15-pin D-sub.
5. Read both EEPROM data and confirm it to match with the C212 definition. F. Command definition: PC Host will send 0x7C IIC slave address and then following 4 bytes command I2C Send Command Write Contrast Write Brightness Write Red Gain Write Green Gain Write Blue Gain Read Contrast Read Brightness Read Red Gain Read Green Gain Read Blue Gain Write Bluish(9300K) R-Gain Data to NVRAM Write Bluish(9300K) G-Gain Data to NVRAM Write Bluish(9300K) B-Gain Data to NVRAM Write sRGB(6500K) R-Gain Data to NVRAM Write sRGB(6500K) G-Gain Data to NVRAM Write sRGB(6500K) B-Gain Data to NVRAM Write Reddish(5800K) R-Gain Data to NVRAM Write Reddish(5800K) G-Gain Data to NVRAM Byte1 CA CA CA CA CA C3 C3 C3 C3 C3 AA AA AA AA AA AA AA AA Byte2 55 56 57 58 59 55 56 57 58 59 3C 3D 3E 4C Byte3 Data Data Data Data Data XX XX XX XX XX Data Data Data Data Data Data Data Data Byte4 checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum
4D
4E 5C 5D
92 93 94 95 96 97 98 99
XX XX XX XX XX XX XX XX
Incoming display mode (Input timing) Horizontal Frequency (KHz) 31.47(N) 31.47(N) 37.50(N) 37.88(P) 46.87(P) 48.36(N) 60.02(P) 67.50(P) 64.00(P) 80.00(P) Vertical Frequency (Hz) 70.08(P) 60.00(N) 75.00(N) 60.31(P) 75.00(P) 60.00(N) 75.00(P) 75.00(P) 60.00(P) 75.00(P) Dot Clock Frequency (MHz) 28.32 25.18 31.5 40.00 49.5 65.00 78.75 108.00 108.00 135.00
Resolution *720x400 *640x480 *640x480 *800x600 *800x600 *1024x768 *1024x768 *1152x864 *1280x1024 *1280x1024
Table 2
2.Wire Dressing
a. LVDS Cable with clip
10
11
3. Add Glue
a. C605
12
c. C615
13
Release Notice
Product System (PS)
Subject:
ASS'Y DRAWING-Q7T3(767S)
99.L8372.000 99.L8372.000-C3-328-001
Rev.:
99.L8372.001 Q7T3
Page
of
1. INTRODUCTION................................................................................................................................... 3 2. OPERATIONAL SPECIFICATION .................................................................................................... 3 2.1 ENVIRONMENT ..................................................................................................................................... 3 2.2TRANSPORTATION ................................................................................................................................. 3 2.3 PACKING CONFIGURATION ................................................................................................................... 5 2.4 ELECTROSTATIC DISCHARGE REQUIREMENTS ..................................................................................... 7 2.5 SAFETY REQUIREMENTS ...................................................................................................................... 7 2.6 EMI REQUIREMENTS ........................................................................................................................... 7 2.7 RELIABILITY ........................................................................................................................................ 8 2.8 MECHANICAL DESIGN FOR TCO 99:.................................................................................................... 8 2.9 ENVIRONMENT PROTECTION DESIGN:.................................................................................................. 8 2.10 ACOUSTICAL NOISE ........................................................................................................................... 8 3. INPUT / OUTPUT SIGNAL SPECIFICATION ................................................................................. 8 3.1 INPUT SIGNAL REQUIREMENTS ............................................................................................................ 8 3.2 FUNCTION ............................................................................................................................................ 9 3.3 NUMBER OF DISPLAY COLORS: 226K COLOR NUMBERS...................................................................... 10 3.4 ADJUSTMENT FUNCTION .................................................................................................................... 10 3.5 DISPLAY POWER MANAGEMENT SYSTEM (DPMS)............................................................................ 10 3.7 PANEL OPTICAL CHARACTERISTICS NOTE ...................................................................................... 12 3.8 BACK-LIGHT UNIT........................................................................................................................ 14 4. FUNCTIONAL SPECIFICATION ..................................................................................................... 14 4.1 DISPLAY QUALITY ............................................................................................................................. 14 5. PHYSICAL SPECIFICATIONS ......................................................................................................... 15 5.1 PHYSICAL DIMENSION & APPEARANCE ............................................................................................. 15 5.2 CONSTRUCTION AND MATERIALS ON OUTER SURFACE....................................................................... 15 5.3 BASE .................................................................................................................................................. 15 5.4 MARKING & LABELS ......................................................................................................................... 15 5.5 PACKAGING ....................................................................................................................................... 15 6. MAINTAINABILITY SPECIFICATIONS........................................................................................ 15 6.1 GENERAL & REQUIREMENTS ............................................................................................................. 15 6.2 MEAN TIME TO REPAIR ...................................................................................................................... 15 6.3 ACCESSIBILITY................................................................................................................................... 16
6.4 EQUIPMENT & TOOLS REQUIRED ....................................................................................................... 16 6.5 ELECTRICAL EMISSION AND ENERGY SAVING SUMMARY FOR TCO99............................................... 16
(c) " EXIT "key: back to main menusleave OSD or enter volume hot-key function. (d) " 3 " key: For left adjustment and enter Contrast Hot-key function. (e) " 4 " key: For right adjustment and enter Brightness Hot-key function. (f) I-Key: For auto-adjustment picture.
- OSD window for control and information display with 8 languages selection. - DPMS (Display Power Management System) - Power on/off indicator. - Tilt base (with tilt function from 0 to +25 degree). -DDC2B function supported. It is composed of the following materials: -A LCD monitor (a) Head part: (1) A LCD module (AU M170EN05). (2) An Inverter +AC-DC board (3) An Interface board. (4) A control board. (5) A 15pin D-sub connector (b) Base part: (1)Tilt base. - A power cord - An user menu.
2. Operational Specification
2.1 Environment 2.1.1 Temperature
-Operating -Non-operating +0 to +40 degrees Celsius -20 to +60 degrees Celsius
2.1.2 Humidity
-Operating -Non-operating 10 to 90% Max. Non-condensing 10 to 95% Max. Non-condensing
2.1.3 Altitude
-Operating -Non-operating 0 to 3,048m (10,000ft) 0 to 12,192m (40,000ft)
A) Sine-wave vibration for initial resonance sweeps and dwells * Sine sweep Frequency (Hz) 5 ~ 26.6 26.6 ~ 50 50 ~ 500 Status 0.6G 0.016" 1.5G
Sweep times: 1 sweep / Per Axis (X, Y, and Z Axis) * One major resonance dwell is required for each axis. Total dwell time at each resonance point shall be 15 minutes. B) Random Vibration Frequency (Hz) 5 ~ 100 100 ~ 200 200 Slope (dB/Oct.) Spectrum Level (g2/Hz) 0 -6 --Equivalent to 1.47 G rms * Duration: 30 Minutes / Per Axis (X, Y, and Z Axis) Total test time: 90 Minutes 0.015 --0.0038
Weight (Kg) 0-9 > 9 - 18.2 > 18.2 - 27.2 > 27.2 - 45.4 > 45.4 - 68.1 > 68.1 - 113.5
B) Drop Sequence
Container Type
40'*8'*8'6" Steel
Gross Weight (Kegs) Tare Payload Length Interior Measurement (mm) Width Height Volume (Cubic Meter) Width Door opening (mm) Height
1050
with pallet
2100
Pallet A: 56 Pallet B: 84
2.7 Reliability
1. The prediction MTBF of display unit shall be greater than 60,000 hours excluding the lamp. (at 25 ) 2. Lamp lifetime: 30,000 hrs minimum at which brightness of lamp is 50% compare to that of initial value at 7.0mA and 25.
5 10
3.2 Function
3.2.1 Support timing
This Interface board is designed to operate in any of the following video mode.
Incoming display mode(Input timing) Resolution 640x350 *720x400 640x480 640x480 640x480 640x480 800x600 800x600 *800x600 Horizontal Frequency (KHz) 31.47(P) 31.47(N) 31.47(N) 35.00(N) 37.86(N) 37.50(N) 37.88(P) 48.08(P) 46.86(P) Vertical Frequency (Hz) 70.08(N) 70.08(P) 60.00(N) 67.00(N) 72.80(N) 75.00(N) 60.32(P) 72.19(P) 75.00(P) Dot Clock Frequency (MHz) 25.17 28.32 25.18 30.24 31.5 31.5 40.00 50.00 49.50 Remark DOS DOS DOS Macintosh VESA VESA VESA VESA VESA Multi-scan operation Actual display resolution 1280x943 full screen 1280x1024
3.3 Number of display colors: 226K color numbers 3.4 Adjustment function
Luminance: Brightness Contrast Geometry: H. Position V. Position Pixel Clock Phase Color gain (Red, Green, Blue) OSD: H. Position V. Position OSD Time Multi-language selection Recall function: Position Recall Color Recall Recall All Miscellaneous: Display Information. OSD Halftone
10
3.6.4 Power Management Mode Normal Off H/Vsync Both exist None or Only one exist Power consumption < 45W < 3W LED Color (Status) Green (Normal) Amber Recovery Time -5 sec
11
Condition
=0,=0 =0 (CR>=10) =0 (CR>=10) =0 (CR>=10) =0 (CR>=10) Tr Tf Tr+Tf Center point at CCFL 7.0mA White Wx Wy Rx
Symbol
CR -
Min.
250
Typ.
450 70 70 70 70
Max.
-
Unit
Deg. Deg. Deg. Deg. ms ms ms
Viewing Angle
4 12 16
260 0.28 0.30 0.61 CIE1931 =0, =0 0.26 0.58 0.11 0.04 0.29 0.61 0.14 0.07 0.31 0.31 0.33 0.64 0.34
cd/m
Chromaticity
Red
Ry Gx Gy Bx By
Green
Blue
1. Viewing Angle, Contrast Ratio, Response Time, Reflectance, and Chromaticity are measured at panel center. 2. Viewing Angle,
12
100% 90%
TrD measures the transition time of L1 relative luminance from black to white state, from 10% to 90% (see graph below) 5. Flicker is measured at cyan dot pattern of Forground RGB (0,0,0) and Background RGB (0,31,31). 6. The variation in surface luminance of these 9 points is defined as below:
13
SYMBOL lf
VL
MIN 3.0 40 -
MAX 7.5 80 -
Condition IL=7.0mArms *1
*2 IL=7.0ma Continuous Operation
Startup Voltage
0C 25 2C
*1.Lamp frequency of inverter may produce interference with horizontal synchronous frequency,and this may cause horizontal beat on the display.Therefore,please adjust lamp frequency,and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference *2. Definition of the lamp lifetime Luminance: L under 50% of specification Starting Lamp Voltage: VS < 1700V, Ta=0 VS < 1200V, Ta=25
4. Functional specification
All the tests to verify specifications in this section must be performed under the following standard conditions unless otherwise noted. The standard conditions are: -Temperature: 5 to 40 degree Celsius -AC line input voltage: 90 Vac to 264 Vac, 47Hz or 63Hz -Warm-up time: 30 minutes minimum
14
5. Physical Specifications
5.1 Physical Dimension & Appearance
5.1.1 Overall Dimensions: 375mm (W) X 370mm (H) X 155mm (D) 5.1.2 Outer Appearance: see Fig.1
5.3 Base
(1)Tilt: fiest hinge:0~ 25 , second hinge : 25 ~135
5.5 Packaging
5.5.1 Carton Dimension: 385mm (W) X455mm (D) X 1478mm (H) (LCD monitor) 5.5.2 Shipping Weight: 6.2kg (LCD monitor) 5.5.3 Shipping Container: 2100 sets per 40 feet container with pallet.
6. Maintainability Specifications
6.1 General & Requirements
6.1.1 Installation: From outside of unit with standard tools and documentation provided to user. 6.1.2 Periodic Maintenance: No periodic maintenance is required. 6.1.3 Repair & Calibration: Require spare modules or components as specified as followings:
(1) Interface board ASSY (2) AC-DC converter board ASSY (1) Control board ASSY
15
6.4.2 Documentation
A service manual will be available which covers all service requirements. A users manual written in Japanese German, Italian, Spanish, France and English will be available to ship with the product.
Appendix 1 Shipment Conditions ITEM Power Brightness Contrast OSD- Timeout OSD-Language OSD-Image size OSD-Color temp State OFF 90 50 20s English Full Screen CU MODE
16
17
Screw Holes
Optical Points
5 4 3 2
H1
9 8 7 6
5 4 3 2
H2
9 8 7 6
5 4 3 2
H3
9 8 7 6
5 4 3 2
H4
9 8 7 6
OP1 OP
OP2 OP
OP3 OP
OP4 OP
OP5 OP
OP6 OP
OP7 OP
OP8 OP
OP9 OP
OP10 OP
OP11 OP
OP12 OP
OP13 OP
OP14 OP
HOLE-V8
HOLE-V8
HOLE-V8
HOLE-V8
Benq Corporation
Project Code 99.L8372.001 Title INTERFACE BOARD Size PCB P/N <Size> 48.L8301.S11 PCB Rev. Document Number S11 99.L8372.000-C2-204-004 1 5 of Approved By DAVEN WU R ev. 0 Model Name Q7T3-FP767S OEM/ODM Model Name NA
JAMSON LIU
1
+3.3V
D N1 3 BAV99
DN2 3 BAV99
2
D N3 3 BAV99
B+ R1 +3.3V 75 R-
R4 56
C2 0.01U 50V K
BLUE+
D
R7 22 R8 56
REDGREEN+
G+ R2
DN100 3 BAV99 75 R10 GJ1 PC5V TP1 TP3 TP5 D1 TZMC5V1 C1 0.1U 16V K U1 R5 2.7K R6 2.7K Cable-Detect TP8 TP11 22 C5 0.01U 50V K
GREEN-
2 3
BAV70LT1
2 4 6 8 10 12 14 16
CON16
1 3 5 7 9 11 13 15
R+ R3 75
R12 56
C6 0.01U 50V K
RED+
1 2 3 4
A0 A1 A2 VSS
8 7 6 5
R9 R11
47 47
AT24C02A
C9 47P 50V J
D2 TZMC5V1
2
D3 +3.3V TZMC5V1
DSUB_SCL
14
R14 100
U2A 2 74LVC14A
14
3 14
VS
R15 100 D5 R17 10K C11 47P 50V J C12 47P 50V J
U 2C 6 74LVC14A
14 9
U2D 8 74LVC14A
HS
TZMC5V1
10K
TZMC5V1
D4
R16
+3.3V +3.3V
B B
RXC-
TP22
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
2061106212
D N5 BAV99
2
RX0M D N7 BAV99
D N6 1
DVIPC5V
RX0P D N8 BAV99
RX1-
RX1M D N9 BAV99
BAV70LT1
U3
OPEN
R18 4.7K
R19 4.7K
1
RX1P DN10 BAV99
TP23
RXC+
RX1+
A0 A1 A2 VSS
8 7 6 5
DVISCL DVISDA
2 3
1
RX2-
TZMC5V1
TZMC5V1
TZMC5V1 RX2+
D6
D7
D8
DVIPC5V
1
RXC-
1
RXC+
RXCP
Benq Corporation
Project Code 99.L8372.001 Title INTERFACE BOARD Size PCB P/N <Size> 48.L8301.S11 P CB Rev. Document Number S11 99.L8372.000-C2-204-004 2 5 of Approved By DAVEN WU Rev. 0 Model Name Q7T3-FP767S OEM/ODM Model Name NA
JAMSON LIU
+3.3V L1 3.3V_SDDS
BEAD + C17 22U 16V C18 0.1U 16V K C19 0.1U 16V K
+2.5V +3.3V L3 BEAD +3.3V L4 3.3V_RGB + BEAD C23 22U 16V C24 0.1U 16V K C25 0.1U 16V K C26 0.1U 16V K C27 0.1U 16V K 3.3V_RDDS C20 0.1U 16V K
+3.3V
146 144
150
141 139
D CLK
DCLK_TTL
D
AVDD_SDDS VDD_SDDS_3.3
AVDD_ADC AVDD_BLUE AVDD_GREEN AVDD_RED SGND_ADC AGND_ADC AGND_BLUE AGND_GREEN AGND_RED AVDD_IMB AVDD_RX2 AVDD_RX1 AVDD_RX0 AVDD_RXC AGND_IMB AGND_RX2 AGND_RX1 AGND_RX0 AGND_RXC AGND_RXPLL
AVDD_DDDS VDD_DDDS_3.3
VDD_DPLL_3.3 RVDD RVDD RVDD RVDD RVDD RVDD RVDD RVDD RVDD
AVDD_RPLL
6 3
+3.3V L5 3.3V_DVI + BEAD C28 22U 16V C29 0.1U 16V K +2.5V C30 0.1U 16V K C31 0.1U 16V K L6 BEAD + C33 22U 16V 2.5V_RXPL C34 0.1U 16V K C32 0.1U 16V K
DCLK/TCON_OCLK DEN/TCON_ECLK DVS/TCON_FSYNC DHS/TCON_LP PD47/OB7 PD46/OB6 PD45/OB5 PD44/OB4 PD43/OB3 PD42/OB2 PD41/OB1 PD40/OB0 PD39/OG7 PD38/OG6 PD37/OG5 PD36/OG4 PD35/OG3 PD34/OG2 PD33/OG1 PD32/OG0 PD31/OR7 PD30/OR6 PD29/OR5 PD28/OR4 PD27/OR3 PD26/OR2 PD25/OR1 PD24/OR0 PD23/EB7 PD22/EB6 PD21/EB5 PD20/EB4 PD19/EB3 PD18/EB2 PD17/EB1 PD16/EB0 PD15/EG7 PD14/EG6 PD13/EG5 PD12/EG4 PD11/EG3 PD10/EG2 PD9/EG1 PD8/EG0 PD7/ER7 PD6/ER6 PD5/ER5 PD4/ER4 PD3/ER3 PD2/ER2 PD1/ER1 PD0/ER0
118 115 117 116 110 109 108 107 106 105 104 103 102 101 100 99 96 95 94 93 92 91 90 87 86 85 84 83 80 79 78 77 76 75 74 73 72 71 70 69 66 65 64 63 62 61 60 59 58 57 56 55 119 120 121 122 123 124 125 126 127 49 48 128 44 45 52 51 39 50 47 46 43 42 41 40
D EN D HS DVS
4 R N1 3 2 1 100
5 6 7 8
173 181 187 193 196 175 178 184 190 197 198 199
C N1 22P OPEN
C N2 22P OPEN
C N3 22P OPEN
C N4 22P OPEN
C N6 22P OPEN OB7 OB6 OB5 OB4 OB3 OB2 OB1 OB0 OG7 OG6 OG5 OG4 OG3 OG2 OG1 OG0 OR7 OR6 OR5 OR4 OR3 OR2 OR1 OR0 EB7 EB6 EB5 EB4 EB3 EB2 EB1 EB0 EG7 EG6 EG5 EG4 EG3 EG2 EG1 EG0 ER7 ER6 ER5 ER4 ER3 ER2 ER1 ER0
8 7 6 5
1 100 2 3 4 RN4
8 7 6 5
+3.3V +3.3V +3.3V +3.3V +3.3V +3.3V +3.3V R22 14.318MHZ 1KF R25 R26 10K OPEN R27 10K R28 10K R29 100K OPEN C36 C35
VDD_RXPLL_2.5 AVSS_RPLL AVSS_SDDS AVSS_DDDS PPWR PBIAS TCLK XTAL GPIO20/HDATA3 GPIO19/HDATA2 GPIO18/HDATA1 GPIO17/HDATA0 GPIO16/HFS GPIO22/HCLK DDC_SCL DDC_SDA RESETn GPIO21/IRQn RED+ REDGREEN+ GREENBLUE+ BLUEHSYNC VSYNC ADC_TEST RXC+ RXCRX2+ RX2RX1+ RX1RX0+ RX0REXT ROM_ADDR15 ROM_ADDR14 ROM_ADDR13 ROM_ADDR12 ROM_ADDR11 ROM_ADDR10 ROM_ADDR9 ROM_ADDR8 ROM_ADDR7 ROM_ADDR6 ROM_ADDR5 ROM_ADDR4 ROM_ADDR3 ROM_ADDR2 ROM_ADDR1 ROM_ADDR0 ROM_DATA7 ROM_DATA6 ROM_DATA5 ROM_DATA4 ROM_DATA3 ROM_DATA2 ROM_DATA1 ROM_DATA0 RVSS RVSS RVSS RVSS RVSS RVSS RVSS RVSS RVSS ROM_OEn CVSS CVSS CVSS CVSS CVSS
1 100 2 3 4 R N5
8 7 6 5
4.7P J
1 100 2 3 4 RN6
8 7 6 5
113 114
4.7P J TCLK XTAL
1 3
C
2N3906 Q2
Re set Circuit
VOL_ON/OFF LVDS_EN LED_GRN
10K OPEN
1 100 2 3 4 R N7
8 7 6 5
R69 51K
1 100 2 3 4 RN8
8 7 6 5
R31 3KF
R68 10K
U4
Cable-Detect
1 100 2 3 4 R N9
8 7 6 5
DSUB_SCL DSUB_SDA
Res et
GM2120
710212000E
1 100 2 3 4 RN10
8 7 6 5
+3.3V
U9
1N4148
1 2 3
NC VSS NC
VDD
R70 10K
D9
P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2 P.2
RED+ REDGREEN+ GREENBLUE+ BLUEHS VS RXCP RXCM RX2P RX2M RX1P RX1M RX0P RX0M 3.3V_DVI R36 1KF RMADDR15 RMADDR14 RMADDR13 RMADDR12 RMADDR11 RMADDR10 RMADDR9 RMADDR8 RMADDR7 RMADDR6 RMADDR5 RMADDR4 RMADDR3 RMADDR2 RMADDR1 RMADDR0 RMDATA7 RMDATA6 RMDATA5 RMDATA4 RMDATA3 RMDATA2 RMDATA1 RMDATA0 ROM_OEn C39 0.1U 16V K
171 170 167 166 163 162 137 136 159 194 195 179 180 185 186 191 192 174 8 9 10 11 12 13 14 15 16 17 18 19 22 23 24 25 28 29 30 31 32 33 34 35 36
1 100 2 3 4 RN11
8 7 6 5
RES
4
C101 1U 10V Z
V6300L OPEN
1 100 2 3 4 RN12
8 7 6 5
1 100 2 3 4 RN13
8 7 6 5
Re set Circuit
R37
B
R38 10K
TCON_OSP TCON_OPOL TCON_OINV TCON_ESP TCON_EPOL TCON_EINV TCON_RSP2 TCON_RSP3 TCON_RCLK GPIO10/TCON_ROE3 GPIO9/TCON_ROE2 TCON_ROE GPIO4/UART_D1 GPIO5/UART_D0 GPIO13 GPIO12 GPIO8/IRQINn GPIO11 GPIO7 GPIO6/EXTCLK GPIO3/TIMER1 GPIO2/PWM2 GPIO1/PWM1 GPIO0/PWM0
+3.3V
+3.3V
2 7
R35
10K
C N8 22P OPEN
C N9 22P OPEN
U6 SST 39VF010
31 30 2 3 29 28 4 25 23 26 27 5 6 7 8 9 10 11 12 24 22 WE NC/A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 OE CE
RXD TXD SCL SDA FLASH_WE I_KEY KEY_DEC KEY_INC KEY_MENU PW_SW VOLUME BRT_ADJ R45 R46 10K R47 10K R48 10K R49 10K R50 10K R51 10K SCL SDA R40 10K R41 10K +3.3V C38 0.1U 16V K U7
R42 R43 R44 10K 10K 10K RMADDR14 RMADDR9 RMADDR8 +3.3V R52 10K
RMADDR15 RMADDR14 RMADDR13 RMADDR12 RMADDR11 RMADDR10 RMADDR9 RMADDR8 RMADDR7 RMADDR6 RMADDR5 RMADDR4 RMADDR3 RMADDR2 RMADDR1 RMADDR0
21 20 19 18 17 15 14 13
Int_Test CLKOUT
201
10K
8 7 6 5
NC NC NC GND
1 2 3 4
NC VCC GND
1 32 16
+3.3V
AT24C16 16K
3 21 38 54 68 82 98 112 130
J3 TXD RXD
3 2 1
CON_3P_S
RS232
NAME USER_BITS(4:0) Reserved SCLPOL HOST_PROTOCOL HOST_PORT_EN OCM_START USER_BITS(7:5) OSC_SEL OCM_ROM_CFG(1)
SET x x x 0 1 1 x 0 1
DESCRIPTION Available for reading from a status register If using 6-wire host protocol, program this bit to 0 Determines polarity of HCLK signal If using 6-wire host protocol, program this bit to 1 GPIO(22:16) is on "Host Port" pins 1 = OCM becomes active after OCM_CLK is stable
1
+2.5V +3.3V
A
Benq Corporation
Project Code 99.L8372.001 Model Name Q7T3-FP767S INTERFACE BOARD Size PCB P/N <Size> 48.L8301.S11 P CB Rev. Document Number S11 99.L8372.000-C2-204-004 3 5 of Approved By DAVEN WU Rev. 0 OEM/ODM Model Name NA
Title
Available for reading from a status register 0 = XTAL and TCLK pins are connected
Tuesday, February 11, 2003 Date: Sheet Reviewed By Prepared By ANGEL HU JAMSON LIU
1
14 U2E 10 14 74LVC14A 7
LED_GRN
11
R53 200
LED_ORG
D
13
U2F 12 74LVC14A
R54 100 1 2 3 4 5 6 7 8 9 C65 100P 50V J C67 0.1U 16V K C68 0.1U 16V K
J4
D
R56 1K R60 1K R59 1K C63 100P 50V J C64 100P 50V J C61 100P 50V J C62 100P 50V J C66 100P 50V J
2060091109
R23 0
C C
J5 1 2 3 4 5 6 7 8 9 10 11 12 13 14
B
L15 +5V L18 +3.3V VOLUME VOL_ON/OFF +3.3V 1 C70 0.1U K 1 1 U5 IRU1206-25CY GND GND IN OUT 3 C71 0.1U K 2 1 + +2.5V
B
20.72060.207
Benq Corporation
Project Code 99.L8372.001
A
Title Size PCB P/N <Size> 48.L8301.S11 Date: PCB Rev. Document Number S11 99.L8372.000-C2-204-004 4 5 of Approved By DAVEN WU
1
R ev. 0
Tuesday, February 11, 2003 Sheet Reviewed By Prepared By ANGEL HU JAMSON LIU
1
C82 0.1U 16V K
D
VCC TXIN5 TXIN6 TXIN7 GND TXIN8 TXIN9 TXIN10 VCC TXIN11 TXIN12 TXIN13 GND TXIN14 TXIN15 TXIN16 VCC TXIN17 TXIN18 TXIN19 GND TXIN20 TXIN21 TXIN22 TXIN23 VCC TXIN24 TXIN25
THC63LVDM83A T.L.
TXIN4 TXIN3 TXIN2 GND TXIN1 TXIN0 TXIN27 LVDS GND TXOUT0TXOUT0+ TXOUT1TXOUT1+ LVDS VCC LVDS GND TXOUT2TXOUT2+ TXCLK OUTTXCLK OUT+ TXOUT3TXOUT3+ LVDS GND PLL GND PLL VCC PLL GND PWR DWM TXCLK IN TXIN26 GND
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
2 3 4 5
U8
1
R61 100K
S T.L. D S S G
GF4435
8
D
2 3 4
D D D
7 6
+
LCD_PW
1
C83 47U 16V
6 7 8 9
5 2
LCD_ON
R62 20K
3 1 1 2
+ C85 10U 16V R63 10K Q1 2N3904 E2E2+ ECLKECLK+ E3E3+ +3.3V
10 11 12 13
14 15 16 17
18 19 20 21
EB3 EB4
C
22 23 24 25 26
L8
34 33 32 31 30 29
DCLK_TTL DEN_TTL C89 0.1U 16V K + C90 22U 16V
C
+3.3V
EB5
L11 BEAD
DHS_TTL DVS_TTL
27 28
BEAD
LVDS_EN
"L" "H"
+3.3V IC2
2 4 6 8 10 12 14 16 18 20
1 3 5 7 9 11 13 15 17 19
20D0017210
1
C94 0.1U 16V K OR7 OR5 OG0
VCC TXIN5 TXIN6 TXIN7 GND TXIN8 TXIN9 TXIN10 VCC TXIN11 TXIN12 TXIN13 GND TXIN14 TXIN15 TXIN16 VCC TXIN17 TXIN18 TXIN19 GND TXIN20 TXIN21 TXIN22 TXIN23 VCC TXIN24 TXIN25
THC63LVDM83A T.L.
TXIN4 TXIN3 TXIN2 GND TXIN1 TXIN0 TXIN27 LVDS GND TXOUT0TXOUT0+ TXOUT1TXOUT1+ LVDS VCC LVDS GND TXOUT2TXOUT2+ TXCLK OUTTXCLK OUT+ TXOUT3TXOUT3+ LVDS GND PLL GND PLL VCC PLL GND PWR DWM TXCLK IN TXIN26 GND
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
2 3 4 5
OG1
B
6 7 8 9
+3.3V
OG2 OG6
10 11 12 13
8 7 6 5 4 3 2 1
2060089108
LCD_PW
14 15 16 17
18 19 20 21
+3.3V
22 23 24 25 26
L13
34 33 32 31 30 29
DCLK_TTL DEN_TTL
A
L14
A
BEAD
DHS_TTL DVS_TTL
27 28
Benq Corporation
Project Code 99.L8372.001 Title INTERFACE BOARD Size PCB P/N <Size> 48.L8301.S11 P CB Rev. Document Number S11 99.L8372.000-C2-204-004 5 5 of Approved By DAVEN WU Rev. 0 Model Name Q7T3-FP767S OEM/ODM Model Name NA
JAMSON LIU
Power off No
Yes
Turn on power
No
No
Check Power BD
No
Check control BD
No
No
No
Replace interface BD
Replace panel
Is control BD connecting?
No
Yes
Yes
No Check Interface BD
3. OSD function:
OSD doesnt work
Is control BD working?
No
Replace control BD
Check interface BD
Y Replace Q761 IC751 PIN 9 IS 15V? N N Plug CN701 again or checking I/F BD PWM existed? (BLT_ADJ) Y N Plug CN601 again or checking PW BD Turn on level existed? (BLT_ON) Y N Insert them again Check CN752, CN753 was pluged properly? Y
Y LED shined? N Y 3.3V existed? Y Replace new fuse N IS I/F board connected? N
gm2120
Inverter board AC-DC PW BD board
EEPROM MCU Flash ROM
AC AC Socket socket
DDC IC
D-sub connector
Control board
AC input
III. Circuit operation theory: A.) HEAD: A-1.) Interface board diagram:
To LCD module
gm2120
ROM
FLASH-
EEPROM
SCL SDA
DDC
(b) IC introduction:
1.) DDC (Display Data Channel) function: We use DDC IC to support DDC/2B function. DDC data is stored in 24C02(EEPROM). Those data related to LCD monitor specification. PC can read them by SDA and SCL serial communication for IC communication for DDC2B. 2.) Gm2120 IC: There are A/D, Scaling, OSD, MCU functions in the Gm2120 IC. Scaling IC is revolutionary scaling engine, capable of expanding any source resolution to a highly uniform and sharp image, combined with the critically proven integrated 8 bit triple-ADC and patented
EMI Filter
Inverter circuit
PWM controller
Switching element
Feedback Isolation
Fig.1
#1 EMI Filter
This circuit (fig. 2) is designed to inhibit electrical and magnetic interference for meeting FCC, VDE, VCCI standard requirements.
Fig. 3
Q7T3(AUO Panel) LCD Monitor Service Guide Circuit Operation Theory #3 Switching element and Isolation power transformer
When the Q601 turns on, energy is stored in the transformer. During Q601 turn-off period, the stored energy is delivered to the secondary of transformer. R607, C607 and D601 is a snubber circuit. R615 is current sense resistor to control output power. (See Fig.4)
Fig. 5
Q7T3(AUO Panel) LCD Monitor Service Guide Circuit Operation Theory #5 PWM Controller
The current mode control IC UC3842B is used to control PWM. When the VCC terminal of it gets 16V, IC601 turns on. +5V will be set up at Pin8 through soft start circuit, which includes R617, C611, D606 and D605. R616 and C610 generate a fixed frequency saw-tooth wave at Pin4.
Fig. 7
A-3.) Control board introduction:
The main parts of the control board are a push button, and a LED. (a) Push button: Its a simple switch function, pressing it for ON to do the auto adjustment function, releasing it for OFF to do nothing. (c) LED: It indicates the DPMS status of this LCD monitor; green light means DPMS on (Normal operating condition). Amber light means DPMS off (Power off condition).
6
1.Block Diagram:
OSCILATOR CIRCUIT
TRANSFORMER
CCFL
ON/OFF
BRT_ADJ
2. General Specification Input Voltage: 15V Input Current: 2A max. ON/OFF Voltage: 3.3V PWM Duty: 3.3V/47KHz Output Requirement: Max. Output Current: 15mA Min. Output Current: 6mA Lamp Working Voltage: 600Vrms Open Lamp Voltage: 1700Vrms Frequency: 50KHz
The turn-on voltage was controlled by R756 and R757.The inverter was turned on or off by the switching transistors Q761 and Q757, Also regulator IC751 is control by Q761 and Q757 decide supply 15V to inverter part or instead.
TL1451 is a dual PWM controller.C765 and R765 decide the working frequency.BLT_ADJ signal is from control board, control pulse width then decide how much energy delivery to CCFL also decide CCFL brightness. Q741 and Q742 be the buffer to rise the drive capability and the totem poles circuit can improve a capable of driving for Q743.C770 decide the striking time delay.
Royer circuit uses the characteristic of transformer saturation to oscillate. When the DC power inject, Q759 or Q760 will turns on, and the current Ic increases. After a period, the transistor will leave the saturation status and Vce increase. The result causes the voltage of primary coil get lower. Finally the transistor turn off, and another transistor turn on. These statuses are repeated and the pin7 and pin8 of T751 will get a Sin Wave to turn on CCFL.
10
Q7T3(CPT Panel)LCD Monitor Service Guide Alignment Procedure 1.Alignment procedure (for function adjustment)
A. Preparation: 1. 2. Setup input timing VGA_60Hz, Cross-Hatch ( General - I ) pattern. The monitor power on at first time that will enter Factory OSD mode. (If not, Please press Menu and Exit plus Power buttons at the same time. A Factory word will be showed on the upper left hand side of OSD Main menu.) Burn in mode have already started. (See Fig 1.). If it hasnt started, Please choose BURN IN MODE tag and select On to enable burn-in mode.(See Fig2a ,2b) Setup unit and keep it warm up at least 20 minutes
3.
B. Timing adjustment: 1. Enter factory setting area (if it isnt at factory mode, Please press Menu and Exit plus Power buttons at the same time to enter factory mode.). 2. Select timing from Table 1. The timing marked with star sign (*) have to be adjusted. 3. Execute Recall All (press Yes) to clear user area in EEPROM 4. The cursor moves to AUTO Adjust or press I-Key to run AUTO adjustment function.(After AUTO adjustment, Press Exit key to exit AUTO Color Balance function. 6. Check the phase of the image; if phase is not perfect adjust it to the best condition. 7. Adjust the settings to following values: CONTRAST = 50 BRIGHTNESS = 90 OSD TIME = 20 COLOR = sRGB 8. When Factory mode is disable (burn-in mode off) then power off after power on will enter user mode. C. Color balance adjustment: 1. 2. Setup input timing XGA_75Hz, 4 gray pattern.( chroma timing 307 , pattern 45) Enter factory setting area (if it isnt at factory mode, Please press Menu and Exit plus Power buttons at the same time to enter factory mode.). 3. 4. 5. 6. 1. 2. Setup the Burn-in mode is On Select the color to user-preset mode. At Main menu move cursor to AUTO Adjust tag then press the ENTER or I-Key to run AUTO Adjust function, then press RIGHT Key to run Auto Color Balance function . Checking if the picture is no good, reject this monitor. Setup input timing VGA_60Hz, white pattern. Enter factory setting area (if it isnt at factory mode, Please press Menu and Exit plus Power buttons at the same time to enter factory mode.). 3. 4. Move cursor into BUR-IN MODE tag and select On to enable burn-in mode. (If it wants to do Auto Color balance, please select the color to user-preset mode.) Measure color temperature by Minolta CA-110 (or equivalent equipment).
D. Color adjustment:
If the default value cant meet color temperature spec. Please use Auto Alignment to calibrate the color temperature; Bluish, & Reddish and sRGB. The color temperature specification as follows:
Move cursor into BURN IN MODE tag and select Off to disable burn-in mode. Turns off the monitor power.
E. Writing EDID file : 1. 2. 3. 4. Setup a PC with DDC card. Connect PC to monitor with a D-sub signal cable. Please refer to the C212 for the correct EDID file. Runs the writing program to write the EDID file into EEPROM for analog input, ie. 15-pin D-sub.
5. Read both EEPROM data and confirm it to match with the C212 definition. F. Command definition: PC Host will send 0x7C IIC slave address and then following 4 bytes command I2C Send Command Write Contrast Write Brightness Write Red Gain Write Green Gain Write Blue Gain Read Contrast Read Brightness Read Red Gain Read Green Gain Read Blue Gain Write Bluish(9300K) R-Gain Data to NVRAM Write Bluish(9300K) G-Gain Data to NVRAM Write Bluish(9300K) B-Gain Data to NVRAM Write sRGB(6500K) R-Gain Data to NVRAM Write sRGB(6500K) G-Gain Data to NVRAM Write sRGB(6500K) B-Gain Data to NVRAM Write Reddish(5800K) R-Gain Data to NVRAM Write Reddish(5800K) G-Gain Data to NVRAM Byte1 CA CA CA CA CA C3 C3 C3 C3 C3 AA AA AA AA AA AA AA AA Byte2 55 56 57 58 59 55 56 57 58 59 3C 3D 3E 4C Byte3 Data Data Data Data Data XX XX XX XX XX Data Data Data Data Data Data Data Data Byte4 checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum checksum
4D
4E 5C 5D
92 93 94 95 96 97 98 99
XX XX XX XX XX XX XX XX
Incoming display mode (Input timing) Horizontal Frequency (KHz) 31.47(N) 37.50(N) 37.88(P) 46.87(P) 48.36(N) 60.02(P) 67.50(P) 64.00(P) 80.00(P) Vertical Frequency (Hz) 60.00(N) 75.00(N) 60.31(P) 75.00(P) 60.00(N) 75.00(P) 75.00(P) 60.00(P) 75.00(P) Dot Clock Frequency (MHz) 25.18 31.5 40.00 49.5 65.00 78.75 108.00 108.00 135.00
Resolution *640x480 *640x480 *800x600 *800x600 *1024x768 *1024x768 *1152x864 *1280x1024 *1280x1024
Table 2
2.Wire Dressing
a. RSDS Cable
e. Spacer
g. Bracket Cover
10
11
12
13
14
Release Notice
Product System (PS)
Subject:
ASS'Y Drawing
99.L8372.CBE 99.L8372.CBE-C3-328-001
Rev.:
99.L8372.001 Q7T3
Page
of 1
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
I. Introduction:
The Q7T3-CPT is a 17 SXGA (1280x1024) , 26.2 K colors(R, G, B 6-bit data) TFT LCD monitor without multi-media function. Its an analog interface LCD monitor with a 15 pins D-sub signal cable and its compliant with VESA specification to offer a smart power management and power saving function. It also offers OSD menu for users to control the adjustable items and get some information about this monitor, and the best function is to offer users an easy method to set all adjustable items well just by pressing one key, we called it Auto key which can auto adjusting all controlled items. Q7T3-CPT also offer DDC2 function to meet VESA standard.
III. Circuit operation theory: A.) HEAD: A-1.) Interface board diagram:
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
(b) IC introduction:
1.) DDC (Display Data Channel) function: We use DDC IC to support DDC/2B function. DDC data is stored in 24C02(EEPROM). Those data related to LCD monitor specification. PC can read them by SDA and SCL serial communication for IC communication for DDC2B. 2.) PW133A IC : There are A/D, Scaling, OSD, MCU functions in the PW133A IC. Scaling IC is revolutionary scaling engine, capable of expanding any source resolution to a highly uniform and sharp image, combined with the critically proven integrated 8 bit triple-ADC and patented Rapid-lock digital clock recovery system. It also support detect mode and DPMS control. MCU
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
control unit, it controls all the functions of this interface board, just like the OSD display setting, the adjustable items, adjusted data storage, the external IIC communication, support DDC2B. 3.) EEPROM: We use 24C16 to store all the adjustable data and user settings. 4.) FLASH ROM: To stored the source code which is accessed by MCU to run program.
EMI Filter
Inverter circuit
PWM controller
Switching element
Feedback Isolation
Fig.1
#1 EMI Filter
This circuit (fig. 2) is designed to inhibit electrical and magnetic interference for meeting FCC, VDE, VCCI standard requirements.
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
Fig. 3
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory #3 Switching element and Isolation power transformer
When the Q601 turns on, energy is stored in the transformer. During Q601 turn-off period, the stored energy is delivered to the secondary of transformer. R607, C607 and D601 is a snubber circuit. R615 is current sense resistor to control output power. (See Fig.4)
Fig. 5
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory #5 PWM Controller
The PWM controller NCP1200A implements a standard current mode architecture. With an internal structure operating at a fixed 40KHz. Where the switch time is dictated by the peak current set-point. When the current set-point falls below a given value. The output power demand diminishes, the IC automatically enters the so-called skip cycle mode and provides excellent efficiency.
Fig. 7
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
A-3.) Control board introduction:
The main parts of the control board are a push button, and a LED. (a) Push button: Its a simple switch function, pressing it for ON to do the auto adjustment function, releasing it for OFF to do nothing. (c) LED: It indicates the DPMS status of this LCD monitor; green light means DPMS on (Normal operating condition). Amber light means DPMS off (Power off condition).
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
A-4.) Inverter diagram:
1.Block Diagram:
OSCILATOR CIRCUIT
TRANSFORMER
CCFL
ON/OFF
BRT_ADJ
2. General Specification Input Voltage: 15V Input Current: 2A max. ON/OFF Voltage: 3.3V PWM Duty: 3.3V/47KHz Output Requirement: Max. Output Current: 15mA Min. Output Current: 6mA Lamp Working Voltage: 600Vrms Open Lamp Voltage: 1700Vrms Frequency: 50KHz
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
3.Circuit Operation Theorem 3.1 ON/OFF SWITCH
The turn-on voltage was controlled by R756 and R757.The inverter was turned on or off by the switching transistors Q761 and Q757, Also regulator IC751 is control by Q761 and Q757 decide supply 15V to inverter part or instead.
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
3.2 PWM Control circuit
TL1451 is a dual PWM controller.C765 and R765 decide the working frequency.BLT_ADJ signal is from control board, control pulse width then decide how much energy delivery to CCFL also decide CCFL brightness. Q741 and Q742 be the buffer to rise the drive capability and the totem poles circuit can improve a capable of driving for Q743.C770 decide the striking time delay.
10
Q7T3 (CPT panel) LCD Monitor Service Guide Circuit Operation Theory
3.3 Oscillator Circuit
Royer circuit uses the characteristic of transformer saturation to oscillate. When the DC power inject, Q759 or Q760 will turns on, and the current Ic increases. After a period, the transistor will leave the saturation status and Vce increase. The result causes the voltage of primary coil get lower. Finally the transistor turn off, and another transistor turn on. These statuses are repeated and the pin7 and pin8 of T751 will get a Sin Wave to turn on CCFL.
11
3.3V_MCU Q1 2N3906 2 3
3.3V_MCU
J BAV99 DN1 A
J BAV99 DN2 A
R3 75
R4 75 R6 R+ R7 100 100 100 C1 47P J C2 47P J C3 47P J C4 47P J R13 100 100 C5 47P J C6 47P J BLUEBLUE+ G+ R8 B+ R11 100 REDRED+ GREENGREEN+
PC5V
Q2 2N3906 2 3
16
R5
47 1 R9 4.7K
R10 2K
C75 0.1U K
TP11 TP12
DSUB_SDA 17
PC5V_OFF
A-detect
R14
PC5V + + -
100 100
HSYNC VSYNC
C
If both PC5V and 3.3_MCU exist: PC5V_OFF should set "LOW" to prevent PC5V from entering the system. When only PC5V exists: PC5V_OFF should set "HIGH" to provide CPU power. Actually, in the initial state, NO PC5V_OFF, if VGA cable is connected, PC5V exists --> Q4 will ON. That will make 3.3_M = 3.3V.
C8 47P J
C9 47P J
R101 DVIPC5V RX0J K 10 R102 J K 10 R103 J K 10 R104 J K 10 R105 J K 10 R106 J K 10 R107 J K 10 R108 J 10 BAV99 DN12 K A RXCP BAV99 DN11 RXCM A BAV99 DN10 RX2P A BAV99 DN9 RX2M A BAV99 DN8 RX1P A C101 0.01U K BAV99 DN7 RX1M A BAV99 DN6 RX0P A 1 2 3 4 BAV99 DN5 RX0M A C10 0.1U K U1 A0 A1 A2 GND VCC WP SCL SDA 8
B
R20 4.7K
R21 4.7K
RX0+
2061106210 19 17 15 13 11 9 7 5 3 1 J101 20 18 16 14 12 10 8 6 4 2
RX1-
RX1+
AT24C02
RX2-
RX2+
3.3V_MCU
RXC-
D6
D7 BZV55-C5V1
D8
RXC+
BZV55-C5V1 A A
BZV55-C5V1 A
D-detect
Benq Corporation
Project Code 99.L8372.001 Model Name Q7T3 INTERFACE BOARD PCB Rev. Document Number S72 99.L8372.000-C3-304-006 1 6 of Approved By ARIES CHU R ev. 0 OEM/ODM Model Name <OEM/ODM> Title Size PCB P/N <Size> 48.L8301.S72 Date:
Tuesday, December 23, 2003 Sheet Prepared By Reviewed By ANGEL HU ARSENIO LIU
1
3.3V_MCU
C12 0.1U
C13 0.1U
C14 0.1U
C15 0.1U
C16 0.1U
C17 0.1U
D
11 21 84 94 104 114 126 VDDP VDDP VDDP VDDP VDDP VDDP VDDP
AVDD_MPLL
AVDD_PLL
AVDD_DVI AVDD_DVI
AVDD AVDD
18 87 97 117
55 65
35
45 51
53
63 62 60 59 61 58 57 37 38 29 28
RIN0 RIN0M GIN0 GIN0M SOGIN0 BIN0 BIN0M HSYNC0 VSYNC0 DDC1_CLK/GPO8 DDC1_DAT/GPO7
RX2P RX2M RX1P RX1M RX0P RX0M RXCP RXCM VDVI R25 390 F
40 41 43 44 46 47 49 50 52
GA1P GA1N GA2P GA2N LVA3p/GA3P LVA3M/GA3N BA1P BA1N BA2P BA2N BA3P BA3N NC/RB1P NC/RB1N NC/RB2P NC/RB2N NC/RB3P NC/RB3N NC/GB1P NC/GB1N NC/GB2P NC/GB2N NC/GB3P NC/GB3N LVB3P/CLKAP LVB3M/CLKAN LVBCKMP/NC/CLKBP LVBCKP/NC/CLKBN LVB2P/NC LVB2M/NC LVB1P/NC/BB1P LVB1M/NC/BB1N LVB0P/NC/BB2P LVB0M/NC/BB2N NC/BB3P NC/BB3N NC/ESP OSP GPO0 GPO1 GPO2 GPO3 GPO4 AD0 AD1 AD2 AD3 BUS TYPE/NC GNDC GNDC GNDC GNDC GNDP GNDP GNDP GNDP GNDP GNDP GNDP
98 99 100 101 102 103 88 89 90 91 92 93 16 17 22 23 24 25 8 9 12 13 14 15 118 119 120 121 122 123 124 125 128 1 4 5 75 76 83 82 81 80 79 30 77 78 31 6 AD0 AD1 AD2 AD3
GA1P GA1N GA2P GA2N GA3P GA3N BA1P BA1N BA2P BA2N BA3P BA3N RB1P RB1N RB2P RB2N RB3P RB3N GB1P GB1N GB2P GB2N GB3P GB3N CLKAP CLKAN CLKBP CLKBN BB1P BB1N BB2P BB2N BB3P BB3N ESP OSP GPO0 GPO1 GPO2 GPO3 GPO4
3.3V_MCU
U2
VAD
VPLL 1
C20 0.1U
C23 0.1U
VDPLL VDVI L3 220 OHM 2 1 C45 22U 16V 3.3V_MCU L4 220 OHM C24 0.1U C27 0.1U
Add C45 for Diagonal noise. Also reverse L1 and C19. L1, L3 and L4 change to 0 ohm for power ripple reduction.
Current setting=Direct DDR Bus BUStype=High: Direct DDR Bus
+2.5V
C29 0.1U
C30 0.1U
C31 0.1U
C32 0.1U
3 3 3 RESET
R202 100
INT
12M R65
69 71 70 32 72
TXO2+ TXO2-
BRT_ADJ
10K C34 1 C54 + 2 4.7U 25V R28 30K C33 0.1U 4.7P C C35 C36 4.7P C
A
3.3V_MCU
Benq Corporation
R26 4.7K Project Code 99.L8372.001 Title R27 O PEN Size PCB P/N <Size> 48.L8301.S72 Model Name Q7T3 INTERFACE BOARD PCB Rev. Document Number S72 99.L8372.000-C3-304-006 2 6 of Approved By ARIES CHU
1
AVSS_MPLL
AVSS_PLL
R ev. 0
R203
19 86 96 116
68 56 64
36
54
39 42 48
Tuesday, December 23, 2003 Date: Sheet Prepared By Reviewed By ANGEL HU ARSENIO LIU
3.3V_MCU
1 2 3 4
RN4
4.7K
8 7 6 5 8 7 6 5 RN7 4.7K
1 2 3 4
3.3V_M
LED_ORG
D
3.3V_MCU
C43 0.1U K 1
R30 4.7K
R31 4.7K
D
S CL S DA
DA0/P5.0
DA1/P5.1
DA2/P5.2
HSYNC
VSYNC
NC
NC
VDD3
DA3/P5.3
DA4/P5.4
DA5/P5.5
AT24C04N-10SI-2.7 DA8/HLFHO DA9/HALFV 39 38 37 36 35 34 33 32 31 30 29 PW_SW DSUB_SCL I-KEY BLT_ON PANEL_ON A-detect MUTE
3.3V_MCU 3.3V_M
7 8
C301 Scaler
C301 12M 0.1U K 0 C46 22P J Y2 12MHZ R301
RST VDD P6.3/AD3 VSS X2 X1 ISDA/P3.4/T0 ISCL/P3.5/T1 STOUT/P4.2 P6.2/AD2/HLFHI HSDA/P3.1/Txd P1.0 P3.2/INT0 P6.1/AD1 P6.0/AD0 MTV312MV64 SOCKET P/N: 22.10079.044 U5
R88
4.7K
9 10 11
R301MCU
C47
R308 1M
12 13 14
22P J 3.3V_M
15 16 17
4.7K
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
18
19
20
21
22
23
24
25
26
27
VOLUME
R307 10K AD0 R43 100 RESET AD1 INT AD2 AD3 1 2 3 4 RN2 1 2 3 4 4.7K
28
S DA S CL
P1.7
RN5 8 7 6 5
1 2 3 4
WRZ
8 7 6 5
3.3V_M 3.3V_MCU
RN6
8 7 6 5
8 7 6 5
4.7K
3.3V_MCU
R77 220
CON1
MUTE 200ms
B
LED_ORG
Q7 2N3904
200ms
1K INC ENTER EXIT DEC PW_SW I-KEY L12 L13 L10 L11 L301 L302 R46 R47 1K R44 1K R45 1K R304 1K R305 1K TP30 TP31 TP32 TP33 TP28 TP29
VOL_ON_OFF
2060091109
C53 0.1U K
C52 0.1U K
J4 +5V BLT_ON L5 TP153 Z30 VOLUME 1 + 2 C73 47U 25V C77 0.1U K C80 0.1U K C76 0.1U K TP155 TP151 2 4 6 8 10 12 14 1 3 TP157 5 7 9 11 13 2072060207 C71 2 0.1U K C79 0.1U K C78 0.1U K TP152 BRT_ADJ L6 TP154 TP156 1 MUTE C60 0.1U K 3.3V_MCU 3.3V_MCU +2.5V R309 0
220 OHM 1
GMT
VOUT 3 1 + C57 2 22U 25V C61 0.1U K
2 G1
G950T65U
Benq Corporation
Project Code 99.L8372.001 Title Size P CB P/N <Size> 48.L8301.S72 D ate: Model Name Q7T3 INTERFACE BOARD PCB Re v. Document Number S72 99.L8372.000-C3-304-006 3 of 6 Approved By ARIES CHU Rev. 0 OEM/ODM Model Name <OEM/ODM>
Tuesday, December 23, 2003 Sheet Prepared By Reviewed By ANGEL HU ARSENIO LIU
1
LCD_PW Q4 AO3401
G
D
1
+ C68
+5V Q5 2N3904
PANEL_ON
R61
20K
1 2
22U 25V
G(1)
C69 0.1U K
S(2)
D(3)
20K2085030 TP64 BB2N BB2P BB1N BB1P TXO2TXO2+ CLKBN CLKBP CLKAN CLKAP RA3N RA3P RA2N RA2P TXO0TXO0+ TXO1TXO1+ TXO2TXO2+ TXOCTXOC+ TXE0TXE0+ TXE1TXE1+ TXE2TXE2+ TXECTXEC+ TXE3TXE3+ TP43 TP44 TP45 TP46 TP47 TP48 TP49 TP50 TP51 TP52 TP53 TP54 TP55 TP56 TP57 TP58 TP59 TP60 TP61 TP62
5V_PANEL
TP63
G2 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1
G2 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1
J5
Benq Corporation
Project Code 99.L8372.001 Title Size PCB P/N <Size> 48.L8301.S72 Date: Model Name Q7T3 INTERFACE BOARD PCB Rev. Document Number S72 99.L8372.000-C3-304-006 4 of 6 Approved By ARIES CHU
1
C401 0.1U K
A
Re v. 0
Tuesday, December 23, 2003 Sheet Prepared By Reviewed By ANGEL HU ARSENIO LIU
Screw Holes
Optical Points
OP1 OP
C
OP2 OP
OP3 OP
OP4 OP
OP5 OP
OP6 OP
OP7 OP
C
5 4 3 2
H1
9 8 7 6
5 4 3 2
H2
9 8 7 6
5 4 3 2
H3
9 8 7 6
5 4 3 2
H4
9 8 7 6
OP8 OP
OP9 OP
OP10 OP
OP11 OP
OP12 OP
OP13 OP
OP14 OP
HOLE-V8
HOLE-V8
HOLE-V8
HOLE-V8
Benq Corporation
Project Code 99.L8372.001 Title Size PCB P/N <Size> 48.L8301.S72 Model Name Q7T3 INTERFACE BOARD PCB Rev. Document Number S72 99.L8372.000-C3-304-006 5 6 of Approved By ARIES CHU R ev. 0 OEM/ODM Model Name <OEM/ODM>
ARSENIO LIU
1
20K2167050 TP99 RA3N RA3P RA2N RA2P RA1N RA1P GA3N GA3P GA2N GA2P
C
RA3N RA3P RA2N RA2P RA1N RA1P GA3N GA3P GA2N GA2P GA1N GA1P
FB0N FB0P FB1N FB1P FB2N FB2P FG0P FG0N FG1N FG1P FG2N FG2P
TP100 TP101 TP102 TP103 TP104 TP105 TP106 TP107 TP108 TP109 TP110 TP111 TP112 TP113
GA1N GA1P CLKAP CLKAN BA3N BA3P BA2N BA2P BA1N BA1P OSP ESP OSP ESP GPO3 GPO2 GPO4
B
TP114 TP115 TP116 TP117 TP118 TP119 TP120 TP121 TP122 TP123 TP124 TP125 TP126
GPO1 GPO0 5 6 7 8
5 6 7 8 22 4 3 2 1 RN9
LCD_PW TP132
C602 0.1U K
G2 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1 J7
20K2167030 TP127 RB3N RB3P RB2N RB2P RB1N RB1P GB3N GB3P GB2N GB2P GB1N GB1P CLKBP CLKBN BB3N BB3P BB2N BB2P BB1N BB1P BB3N BR0N BB3P BR0P BB2N BR1N BB2P BR1P BB1N BR2N BB1P BR2P RB3N B0N RB3P B0P RB2N B1N RB2P B1P RB1N B2N RB1P B2P GB3N BG0N GB3P BG0P GB2N BG1N GB2P BG1P GB1N BG2N GB1P BG2P TP128 TP129 TP130 TP131 TP133 TP135 TP136 TP137 TP138 TP139 TP140 TP141 TP142 TP143 TP144 TP145 TP146 TP147 TP148 TP149 G2 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1 J6
B
Benq Corporation
Project Code 99.L8372.001 Title Size PCB P/N <Size> 48.L8301.S72 Model Name Q7T3 INTERFACE BOARD PCB Rev. Document Number S72 99.L8372.000-C3-304-006 6 6 of Approved By ARIES CHU
1
R ev. 0
Tuesday, December 23, 2003 Date: Sheet Prepared By Reviewed By ANGEL HU ARSENIO LIU
Power off No
Yes
Turn on power
No
No
Check Power BD
No
Check control BD
No
No
No
Replace interface BD
Replace panel
Is control BD connecting?
No
Yes
Yes
No Check Interface BD
3. OSD function:
OSD doesnt work
Is control BD working?
No
Replace control BD
Check interface BD
Y Replace Q761 IC751 PIN 9 IS 15V? N N Plug CN701 again or checking I/F BD PWM existed? (BLT_ADJ) Y N Plug CN601 again or checking PW BD Turn on level existed? (BLT_ON) Y N Insert them again Check CN752, CN753 was pluged properly? Y
Y LED shined? N Y 3.3V existed? Y Replace new fuse N IS I/F board connected? N