Professional Documents
Culture Documents
5 Release
Introduction
A simple workshop follows to demonstrate how to use the Turbomachinery mode in CFX-Pre and CFD-Post.
This workshop models an Axial fan. The model consists of a single rotating domain for the fan blade with stationary domains upstream and downstream of the blade.
The full axial fan contains ten blades. Due to rotational periodicity a single blade passage will be modeled. Frozen Rotor interfaces are used to connect the rotating and stationary domains.
2012 ANSYS, Inc. December 17, 2012 2 Release 14.5
Turbo-Pre
1. Open Workbench (Start > Programs > ANSYS 14.5 > ANSYS Workbench)
Release 14.5
Basic Settings
The Turbo mode uses a setup wizard to walk you through CFX-Pre. The first step is the Basic Settings panel: 1. Set the Machine Type to Fan 2. Select Z as the Rotation Axis Notice that the rotational axis is displayed in the Viewer 3. Select Analysis Type as Steady State 4. Click Next >
Release 14.5
Component Definition
The Component Definition panel is used to import meshes, select the rotation speed for each component and set the tip clearance (if any).
2.
3. 4. 5.
Release 14.5
Component Definition
The Region Information is used by CFXPre to identify mesh regions of interest. CFX-Pre will try to automatically identify these regions, but manual input may be required depending on how the regions are named in the mesh file. CFX-Pre will automatically create boundary conditions and domain interfaces using these regions, so checking the Region Information at this stage will save time later. The mesh file contains all three components, but only one of those components is to be included in S1 Default values can be used for all other options
Component Definition
Now define the 2nd component which is rotating:
1. Right-click in the Component Definition white space, and select New Component
2. Select Rotating and set the Name as R1 3. Set the Rotating Value to 3000 [rev min^-1] The rotation direction is shown in the Viewer 4. Do not select a mesh file. The mesh has already been imported in the previous step.
Component Definition
6. Expand the Region Information frame and compare with the picture below and make the necessary changes
Component Definition
Now define the 3rd component which is stationary: 1. Create a new stationary component named S2 2. Under Available Volumes select OUTBlock Main 3. Expand the Passages and Alignment frame The number of Passages in 360 and the number of Passages To Model is determined automatically You can change the automatic values or apply a Theta Offset by clicking the Edit button, but this is not necessary for this case, so click cancel
4. Expand the Region Information frame and compare with the picture next page and make the necessary changes
2012 ANSYS, Inc. December 17, 2012 9 Release 14.5
Component Definition
10
Release 14.5
Physics Definition
All Physics settings, including Fluid Type, Inlet & Outlet boundary conditions, Interface types, and Solver Parameters are set in one panel. 1. The default Fluid and Model Data are appropriate for this simulation 2. Select Boundary Template as P-Total Inlet Mass Flow Outlet
The Boundary Template provides quick setup of the most common turbomachinery
boundary combinations
5. Set Mass Flow to Per Component and then enter a Mass Flow Rate of 0.04 [kg s^-1]
2012 ANSYS, Inc. December 17, 2012 11 Release 14.5
12
Release 14.5
Interface Definition
Interfaces are automatically created using the Region Information from the Component Definition panel. 1. Select each interface to verify it has been created correctly There are two Frozen Rotor interfaces, three Periodic interfaces and an interface near the blade tip to connect dissimilar meshes together The interfaces have been correctly created 2. Click Next > to continue
2012 ANSYS, Inc. December 17, 2012 13 Release 14.5
Boundary Definition
Boundary conditions are also automatically created using the Region Information from the Component Definition panel and information from the Physics Definition panel. 1. Select each boundary condition to verify the settings are appropriate 2. Select Next > to continue
14
Release 14.5
Final Operations
The Final Operations panel allows you to Enter General Mode. Enter General Mode is useful if you want to use other CFX-Pre features (profile boundaries, CEL etc) but still complete most of the set up using the Turbomachinery mode.
1. Click Finish
15
Release 14.5
Turbo-Post
In CFD-Post the following features will be demonstrated: Auto Initialize of Turbo Components Modifying Turbo regions Displaying Hubs and Blades using the 3D view Create vector and contour plots using the Blade to Blade View Create vector and contour plots using the Meridional View Use of Turbo Charts and Macros
17
Release 14.5
Turbo-Post GUI
1. Switch to the Projects window 2. View the results in CFD-Post by double clicking Results in the Project Schematic 3. In CFD-Post, click on the Turbo tab 4. Click Initialise All Components For each component CFD-Post detects which regions correspond to the
Hub, Shroud, Blade, Inlet, Outlet and Periodic regions. CFD-Post uses this information to make turbo plots and charts. You can manually assign these regions, or check the auto-assigned regions by editing each of the component object from the Turbo tree (Component 1 (S1), Component 2 (R1) and Component 3 (S2))
5. Select the Three Views toggle You can toggle between a Single View and Three Views. The three views
shown are a 3D view, a Blade to Blade View and a Meridional View
2012 ANSYS, Inc. December 17, 2012 18 Release 14.5
3D View
6. Edit the 3D View object from the Turbo tree The Details of 3D View are shown
The 3D View now shows 3 copies of the Hub and Blade in each of the 3 components
2012 ANSYS, Inc. December 17, 2012 19 Release 14.5
Blade-to-Blade View
Now create a Blade to Blade Vector Plot: 1. Edit the Blade-to-Blade object from the Turbo tree 2. Change Plot Type to Vector 3. Set Sampling to Equally Spaced and # of Points to 400
Blade-to-Blade View
6. In Details of Blade-to-Blade Plot, change the Plot Type to Contour and select the Variable as Total Pressure in Stn Frame, then click Apply. 7. Create a Stream plot of Velocity in the same way Change the number of points to 100 8. Double-click on 3D View in the Turbo tree 9. Enable the Show Blade-to-Blade plot toggle and click Apply to show the blade-to-blade Stream plot in the 3D View
2012 ANSYS, Inc. December 17, 2012 21 Release 14.5
Meridional View
1. Edit the Meridional object from the Turbo tree 2. Generate a Contour plot of Pressure using a Local Range A Contour plot is shown in the Meridional View 3. Now enable the Show Sample Mesh toggle (near the bottom of Details of Meridional Plot ) A mesh is now shown on the Contour plot This illustrates the resolution used in creating the meridional data
22
Release 14.5
Turbo-Post
23
Release 14.5
24
Release 14.5
Tables
The Table Viewer allows you to create a table that can be exported in .html, .csv, or .txt formats. You can also save a state file for a table for later use. Next you will create a table and export it to an html file
1. Select the Table Viewer tab from the bottom of the Viewer window
2. Select the New Table icon and accept the default name from the Table Viewer toolbar
3. In cell A1 type: Mass Averaged Inlet Total Pressure 4. In cell B1, type: =massFlowAve(Total Pressure)@S1 Inlet Alternatively you can use the Table Viewer toolbar to select Insert:
Function > CFD-Post > massFlowAve, then Insert: Variable > Total Pressure, etc to build the expression
2012 ANSYS, Inc. December 17, 2012 25 Release 14.5
Tables
5. In cell A2 type: Mass Averaged Outlet Total Pressure 6. In cell B2, enter the equation: =massFlowAve(Total Pressure )@S2 Outlet
Tables
9. In cell A4 type: Filename 10. In cell B4, select Insert: Annotation > File Name > Name 11. Click the Save Table icon from the Table Viewer toolbar 12. Save the file as axial_table.html 13. Open this file in a web browser
27
Release 14.5
Turbo Reports
CFX Post includes automatic report generation based on templates. A number of Turbo-specific templates are available: 1. From the main menu select File > Report > Report Templates
Turbo Report
You can add you own Figures, Tables, Charts and Comments to the report. Next you will add a figure to the end of the report showing a Vector plot at 50% span in the blade passage. 1. Click the Comment icon from the main toolbar
2. Enter User Plots the for Name 3. Type the following in to the Comment Viewer :
29
Release 14.5
Turbo Report
4. Switch to the Report Viewer, and Refresh the report The Refresh button is in the Report Viewer toolbar The new comment will appear at the end of the report
30
Release 14.5
Turbo Report
Now create a Velocity plot at 50% span:
31
Release 14.5
Turbo Report
Now add this plot to you report: 1. Click the Figure icon from the main toolbar or RightClick in the viewer window and select Copy to New Figure
Turbo Plot
Once the report is complete you can publish it to an html file 1. Click the Publish icon from the Report Viewer toolbar 2. Click OK to write the HTML file The file and figures can be distributed as necessary
33
Release 14.5
CFD-Post
You may want to try the following on your own, time permitting 1. Create various figures, tables, comments and charts that you might typically want to see in your analysis
2. Try enabling the Generate CFX-Viewer Files toggle when publishing your report Image in the report can then be rotated, zoomed and panned. The CFX Viewer must be installed on the machine viewing the report; this is freely available from the Customer Portal and does not require a license (so your customers can view your figures in 3D)
2012 ANSYS, Inc. December 17, 2012 34 Release 14.5