Professional Documents
Culture Documents
Comstar Supply
Comstar Supply
Limited Warranty USER'S GUIDE & SAFETY MANUAL USER'S GUIDE & SAFETY MANUAL
Condux International, Incorporated extends the following To obtain repair or replacement service under the limited
warranty to the original purchaser of these goods for warranty, the purchaser must contact the factory for a
use, subject to the qualifications indicated:
Installation Procedure
NOTE: Before proceeding, ensure that your extension Figure 1
is the correct length (see Table) and that your sheave or
quadrant block uses a 1.25” diameter mounting pin.
,,,,,
1. Lower the base section into the manhole with a rope,
block and tackle, or the truck boom. Do not lower by Locking Pins
hand - the unit is heavy. Figure 2 Figure 3
,,,,,
2. Place the base section in line with the duct. Fully
disengage the cam-lock foot pedal and point it towards
the duct (see Figure 1). Manhole
Base Section
,,,,,
3. Lower the extension into the manhole and place it over
the base section.
Cable
4. Extend the extension at about a 75° angle until it
Cam-lock
contacts the manhole’s inside edge. Insert a locking pin
Foot Pedal Sheave Sheave
through the extension & base sections (see Figure 2).
,,,,,
5. Loosen the bolts in the extension and base. Place the
quadrant block or sheave wheel at the desired height
and insert a locking pin.
,,,,,
Jamb Skid Components
6. Push the sides together into their most narrow
configuration (see Figure 3), and tighten the bolts in the
extension and base.
Duct Duct
7. Align the Jamb Skid and the quadrant block or sheave
Removal Procedure Jamb Skid Jamb Skid
wheel with the duct. Rotate the cam-lock foot pedal
about 3/4 of its rotation away from the duct.
1. Place a leverage bar below the cam-lock foot pedal 75°
8. Push down on the cam-lock foot pedal until it goes and pry up to release the Jamb Skid.
beyond the engaged range and completely locks in
place. If necessary, move the base section towards or 2. Disassemble and remove the Jamb Skid by reversing
away from the duct. the installation procedures.
!WARNING: Read and understand all !CAUTION: Follow all standard man- !WARNING: Do not use around live !CAUTION: The Jamb Skid locking
procedure and safety instructions hole opening procedures, including circuits. The aluminum Jamb Skid is pins rotate freely. Do not use the
before using any Condux Jamb Skid. work area protection and gas detec- highly conductive. Serious personal Jamb Skid as a ladder. Personal
Failure to do so may result in serious tion. Wear personal protective injury or death may result. injury may result.
personal injury or death. Save this equipment: hard hat, safety glasses,
user’s guide for future reference. safety shoes, and leather work gloves.
ADVERTENCIA !ADVERTENCIA: Favor de leer y com- !WARNING: Do not remain in the !WARNING: Ensure the Jamb Skid is !CAUTION: Do not lower the Jamb
prender todas las instrucciones de manhole when pulling cable. During properly aligned with the duct and the Skid sections into the manhole by
operación y seguridad antes de usar el a pulling operation, the Jamb Skid cam-lock foot pedal is fully locked. hand. Personal injury or property
Instrucciones
de Operación Condux® Rope to Rope/Grip Clevis. Si and cable are under tension. Serious Do not exceed 10,000 lbs. of pulling damage may result.
Ud. no comprende las instrucciones personal injury or death may result if force. Failure to do so may result in
favor de consultarle a su jefe. a component fails and releases its stored energy. personal injury or property damage.
5 Blue Heron Drive Collegeville, PA 19426 (610) 831-5020 Fax: (610) 831-5012
www.comstarsupply.com