Professional Documents
Culture Documents
LABORATORY MANUAL
ECE 100
INTRODUCTION TO PRACTICAL
ELECTRONICS
LMECE100: INTRODUCTION TO PRACTICAL ELECTRONICS
Table of contents
Title Page no.
1 Working principle of the Water level indicator circuit 3
2 Working principle of the Touch operated switch 4
3 Working principle of the NOT gate using transistor 5
4 Working principle of the IR switch 6
5 Working principle of the Rain alarm 7
6 Working principle of the Light operated switch 8
7 Working principle of the Soft switch for electrical appliances 9
8 Working principle of the UM-66 base melody generator 10
9 Working principle of the Thermister based heat indicator 11
10 Working principle of the Direction control for DC motor 12
TEXT BOOKS: EFY project books vol 1-5.
LMECE100: INTRODUCTION TO PRACTICAL ELECTRONICS
1. Title: Realization of water level indicator on bread board.
Apparatus required:
S. No Apparatus Specifications Qty. Tolerance
1 Transistor BC548 4 NA
2 LED 3 NA
3 Resistor 220 Ohm 6 +/- 5%
4 Buzzer
5 Battery 9v 1
Learning Objective: Application of transistor as an amplifier.
Circuit Diagram:
Procedure:
Connect the circuit as per circuit diagram.
Empty the water container initially.
Start increasing the water level slowly.
LMECE100: INTRODUCTION TO PRACTICAL ELECTRONICS
Scope of result to be reported: Observe the sequential glowing of LEDs as the water
level increases, also the ringing of Buzzer at overflow.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of battery at any point in circuit.
Do not give direct supply to LEDs.
2. Title: Realization of Touch operated switch on bread board
Apparatus required:
S. No Apparatus Specifications Qty. Tolerance
1 Resistor 1K,100k,10M 1 +/- 5%
2 IC 555 NE555 1
3 Buzzer 1
4 Capacitor 10uF 1
5 LED 1
Learning Objective : Application of IC 555.
Circuit Diagram:
Procedure:
Connect the circuit as per circuit diagram.
Touch the plates with finger.
The LED will glow.
LMECE100: INTRODUCTION TO PRACTICAL ELECTRONICS
Scope of result to be reported: Observe the glow of LED as we touch the plates and the
ringing of Buzzer.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit.
Do not give direct supply to LEDs.
Give proper supply to IC 555.
3. Title: Realization of NOT gate using transistor.
Apparatus required:
S. No Apparatus Specifications Qty. Tolerance
1 Transistor BC548 1
2 Resistor
Objective: Application of Transistor as switch.
Circuit Diagram:
Procedure:
Connect the circuit as per circuit diagram.
Scope of result to be reported: Observe the voltage at Base and Collector with
Multimeter.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit.
4. Title: Realization of the IR switch.
Equipment Required: Wires, Multiple Power Supply, & multimeter.
Material Required: ICs (555, SOTP IR Rx), Capacitor (0.1 F, 4.7 F), Resistors (1K,
22K, 330K, 10K, 100K, variable 20K), Battery (5 V), IR LED and LED.
Objective: Use of IR- transmitter and receiver.
Circuit Diagram:
Figure 1
Procedure:
Connect the circuit as per circuit diagram LED 1 should glow.
Interrupt IR light to reach IR Rx.
Scope of result to be reported: Observe the difference on LED 1 while interrupting the
path. LED 1 glows when there is no interruption and it turns off when there is any
interruption.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit.
5. Title: Realization of the Rain Alarm circuit.
Apparatus required:
S. No Apparatus Specifications Qty. Tolerance
1 IC timer NE 555 1
2 Water sensor 1
3 Capacitor 0.01uF(2),1uF 3
4 Resistor 10K 1
5 Var resistor 500k 1
Objective: Application of IC 555.
Circuit Diagram:
Procedure:
Connect the circuit as per circuit diagram.
Wet the water sensor.
The speaker will produce sound.
LMECE100: INTRODUCTION TO PRACTICAL ELECTRONICS
Scope of result to be reported: Observe the sound of speaker as we wet water sensor.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit.
Give proper supply to IC 555.
6. Title: Realization of the Light Operated switch on bread board.
Apparatus required:
S. No Apparatus Specifications Qty. Tolerance
1 Transistor BC548 1
2 Var Resistor 100K 1
3 Relay 1
4 LDR 1
5 Bulb 60 W 1
6 Bulb holder 1
Objective: Application of LDR.
Circuit Diagram:
Procedure:
Connect the circuit as per circuit diagram.
Scope of result to be reported: Observe the Bulb which turns on when light falls on
LDR as Relay switches on the supply to bulb.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit.
Be very careful of AC supply, do not touch bare wires.
7. Title: Realization of Soft switch for Electrical appliances.
Equipment Required: Wires, Multiple Power Supply & multimeter.
Material Required: Bulb holder,2-ON/OFF switch, IC-CD4027,
Capacitor(0.47uF), Transistor(SL100), Relay, LDR, Bulb(60 W) &
resistor(47K & 8.2K ).
Learning Objective: Application of IC-CD4027.
Procedure:
Connect the circuit as per circuit diagram.
Press the ON/OFF button and turn on the electrical
device.
Circuit Diagram:
Scope of result to be reported: Observe the electrical appliance which
turns on when we press soft ON/OFF switch as Relay switches on the supply to
appliance.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit.
8. Title: Realization of the UM-66 base melody generator on bread board.
Apparatus required:
S. No Apparatus Specifications Qty. Tolerance
1 IC UM 66 1
2 Resistor 0.1uF 1
3 Capacitor 4.7K 1
4 Battery 4.5 v 1
5 Speaker 1
6 Transistor HE8050S 1
Objective: Application of IC-UM66.
Circuit Diagram:
Procedure:
Connect the circuit as per circuit diagram.
Scope of result to be reported: Observe the melodious sound from speaker when we
switch on the supply.
9. Title: Realization of Thermister based heat indicator.
Equipment Required: Wires, Multiple Power Supply & multimeter.
Material Required: Thermister (DC95Y103W), preset resistor, LED
Darlington Transistor (BC-618), Hair Drier.
Learning Objective: Application of Thermister.
Procedure:
Connect the circuit as per circuit diagram.
Switch on Drier and see the LED glowing.
Circuit Diagram
Scope of result to be reported: Observe the melodious sound from
speaker when we switch on the supply.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit..
10. Title: Realization of the Direction control for DC motor circuit.
Apparatus required:
S. No Apparatus Specifications Qty. Tolerance
1 Resistor 10K,2.2K 2 each +/- 5%
2 Diodes IN4007 5
3 Transistor Bc 548 4
4 DC motor 12v
Objective: Application of TRANSISTOR as switch.
Circuit Diagram:
Procedure:
Connect the circuit as per circuit diagram.
Scope of result to be reported: Observe the direction of rotation of motor as we turn on
the switches S1 and S2 alternately.
Cautions:
Connect circuit very carefully with all connections tight and clear.
Do not short circuit +ve and ve terminals of supply at any point in circuit.