Professional Documents
Culture Documents
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
B.
QTY
1
AR
AR
AR
1
DESIGNATION
ACCESS PLATFORM 3M (10 FT)
CAP - BLANKING
PLUG - BLANKING
WARNING NOTICE(S)
LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
C. Referenced Information
REFERENCE
DESIGNATION
(Ref. 25-62-00-910-801-A).
Report the Deployment Results
(Ref. 25-62-42-400-001-A).
Offwing Escape-Slide - Installation
(Ref. 25-62-46-000-001-A).
Inflation Reservoir, Offwing Escape-Slide - Removal
(Ref. 25-62-46-400-001-A).
Inflation Reservoir, Offwing Escape-Slide - Installation
(Ref. 27-50-00-866-008-A).
Extension of the Flaps on the Ground
(Ref. 27-50-00-866-008-A-01).
Extension of the Flaps/Slats on the Ground
(Ref. 53-35-11-000-001-A).
Removal of the Wing-to-Fuselage Fairings
(Ref. 53-35-11-400-001-A).
Installation of the Wing-to-Fuselage Fairings
AIPC 533503
Offwing Escape Slide - Inflated
Offwing Escape-Slide Compartment 7504MM (7505MM)
Page 1 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
7505MM
Z152
A
7504MM
Z151
A
B
15
E
D
OFFWING ESCAPE
SLIDE-INFLATED
LH SHOWN
RH OPPOSITE
E
2
DUAL LANE
ESCAPE SLIDE
7504MM
7505MM
N_MM_256242_4_AAMA_01_00
Page 2 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
B
OFFWING ESCAPE SLIDE
STOWAGE COMPARTMENT
193AT (194AT)
8
7
C
4
D
5
OFFWING ESCAPE
SLIDE RAMP
(SEEN FROM BELOW)
13
14
ESCAPE SLIDE
STOWAGE COMPARTMENT
11
10
12
3
N_MM_256242_4_AAMA_02_00
Page 3 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
EXAMPLE
Z826
151KW
152KW
194AT
Z150
7505MM
7504MM
193AT
7507MM
7506MM
A
EXAMPLE
N_MM_256242_4_ACMA_01_01
Page 4 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
B
EXAMPLE
15
16
D
14
7
17
9
REF 53-35-11
9
REF 53-35-11
11
12
REF 53-35-11
10
EXAMPLE
C
EXAMPLE
~5.0
16
7
8
18
13
N_MM_256242_4_ACMA_02_01
Page 5 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
CRITICAL AREA
DEGREE OF SMOOTHNESS
IN LOF
POSITIVE STEP
AREA A and B
A LOF
NEGATIVE STEP
POSITIVE STEP
NEGATIVE STEP
mm
in.
mm
in.
mm
in.
mm
in.
1.5
0.059
1.5
0.059
1.0
0.039
1.0
0.039
CRITICAL AREA
PERIPHERAL GAPS
PERMISSABLE TOLERANCE ON 10
OF LENGTH
MIN.
MAX.
mm
in.
mm
in.
AREA A
3.0
0.118
1.0
0.039
AREA B
5.0
0.2
1.0
0.039
MIN.
mm
in.
mm
in.
6.5
0.256
1.5
0.059
N_MM_256242_4_ACMA_03_01
Page 6 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
3.
Job Set-up
Subtask 25-62-42-481-051-A
A.
Subtask 25-62-42-941-054-A
B.
4.
Procedure
Subtask 25-62-42-020-051-A
A.
KEEP OFF THE INFLATED ESCAPE-SLIDE. IF YOU GO ON IT, YOU CAN CAUSE DAMAGE TO THE SURFACE MATERIAL.
For each connector: hold the two ends of the connector with a finger and a thumb each. Turn
one end of the connector a quarter turn 90 deg (90.0000 deg) and pull it away from the other
end.
Page 7 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
(e) Loosen the tie-off cord which holds the electrical light cable-assembly on the grommet of the girt.
1
Do step A.(3) again with the FORWAD girt assembly (7) and with the TOP girt assembly (8).
Disconnect the inflation hose (16) from the fuselage (15) and remove the escape slide enclosure
(7) from the aircraft.
Make sure that these components are kept together with the escape slide enclosure (7) and the
attached enclosure door (8):
The seal attach plate (12)
The seal strips (9)
The screws (10)
The countersunk washers (11).
These components are a complete assembly.
Page 8 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
NOTE: If components are damaged or you can not find them, an order of the components as spare parts is possible (Ref. AMM TASK 53-35-11-000-001) ,
(Ref. AMM TASK 53-35-11-400-001) and AIPC 533503.
(6) Record the deployment in the report form (Ref. AMM TASK 25-62-00-910-801)
5.
Close-up
Subtask 25-62-42-860-052-A
A.
TASK 25-62-42-000-001-A
Offwing Escape-Slide - Removal
B.
C. Referenced Information
REFERENCE
(Ref. 24-42-00-861-001-A).
DESIGNATION
Energize the Ground Service Network from the External Power
Page 9 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
REFERENCE
(Ref. 25-62-00-820-001-A).
(Ref. 27-50-00-866-008-A).
(Ref. 27-50-00-866-008-A-01).
(Ref. 52-30-00-860-001-A).
DESIGNATION
Adjustment Procedure to Install the Lockpin in the Regulator Valve Assembly of the Inflation Reservoir - Offwing Escape-Slide
Extension of the Flaps on the Ground
Extension of the Flaps/Slats on the Ground
Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
Removal of the Wing-to-Fuselage Fairings
Installation of the Wing-to-Fuselage Fairings
(Ref. 53-35-11-000-001-A).
(Ref. 53-35-11-400-001-A).
AIPC 533503
Offwing Escape-Slide Compartment 7504MM (7505MM)
3.
Job Set-up
Subtask 25-62-42-861-051-A
A.
Subtask 25-62-42-010-060-A
B.
Get Access
(Ref. Fig. Offwing Escape-Slide Compartment 7504MM (7505MM))
(1) Open the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-001) .
(2) Put an ACCESS PLATFORM 2M (6 FT) in position adjacent to the AFT cargo compartment exit.
(3) Set the AFT CARGO COMPT light switch 8LU to the ON position.
(4) FOR 7504MM (ESCAPE SLIDE OFFWING L)
Remove the access panel 151KW.
(5) FOR 7505MM (ESCAPE SLIDE OFFWING R)
Remove the access panel 152KW.
(6) Safety the applicable inflation reservoir (2):
WARNING: MAKE SURE THAT THE SAFETY/LOCK PIN IS CORRECTLY INSTALLED IN
THE REGULATOR VALVE ASSEMBLY OF THE INFLATION RESERVOIR. THIS
SAFETIES ALL COMPONENTS OF THE INFLATION SYSTEM IN OPERATION AND
PREVENTS ACCIDENTAL:
- DISCHARGE OF THE INFLATION RESERVOIR
- DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
(a) Remove the lockpin assembly (4) from the pocket (1).
(b) Install the lockpin assembly (4) in the valve/regulator assembly (3).
NOTE: If you cannot install the lockpin assembly (4) in the valve/regulator assembly (3) refer to
(Ref. AMM TASK 25-62-00-820-001) .
(7) Safety precautions in the cockpit:
WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE
YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
Page 10 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/
OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
(a) Set the flap/slat control lever to the FULL position (Ref. AMM TASK 27-50-00-866-008) .
(b) Install the LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION (98D27803000000) on the
flap/slat control lever when you work near the flaps.
(c) Put a WARNING NOTICE(S) in position on the flap/slat control lever to tell persons not to
operate the flaps.
(8) FOR 7504MM (ESCAPE SLIDE OFFWING L)
Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position adjacent to the panel 193AT.
(9) FOR 7505MM (ESCAPE SLIDE OFFWING R)
Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position adjacent to the panel 194AT.
4.
Procedure
Subtask 25-62-42-020-050-A
A.
TASK 25-62-42-920-001-A
Remove Offwing Escape Slide for Restoration
1.
Referenced Information
Page 11 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
REFERENCE
(Ref. 25-62-42-000-001-A).
(Ref. 25-62-42-400-001-A).
3.
DESIGNATION
Offwing Escape-Slide - Removal
Offwing Escape-Slide - Installation
Job Set-up
Subtask 25-62-42-010-058-A
A.
Get Access
(1) Remove the offwing escape-slide (Ref. AMM TASK 25-62-42-000-001) .
4.
Procedure
Subtask 25-62-42-920-051-A
A.
Workshop Procedure
(1) Send the offwing escape-slide to the workshop for restoration. Refer to the manufacturer's
Component Maintenance Manual (CMMv) for the correct procedure.
NOTE: The CMMv reference can be found over the IPC P/N for the applicable FIN.
5.
Close-up
Subtask 25-62-42-410-057-A
A.
Close Access
(1) Install a serviceable or replacement offwing escape-slide (Ref. AMM TASK 25-62-42-400-001) .
TASK 25-62-42-400-001-A
Offwing Escape-Slide - Installation
QTY
1
1
1
DESIGNATION
ACCESS PLATFORM 2M (6 FT)
GAGE-THICKNESS, PAINT BORER 518
WARNING NOTICE(S)
Torque wrench: range to 0.30 m.daN (26.55 lbf.in)
Torque wrench: range
to between 0.35 and 0.45 m.daN (30.97 and 39.82 lbf.in)
No specific
Torque wrench: range
to between 3.0 and 3.2 m.daN (22.12 and 23.60 lbf.ft)
(98D27803000000)
1
LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
FOR 7504MM (ESCAPE SLIDE OFFWING L)
No specific
1
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
FOR 7505MM (ESCAPE SLIDE OFFWING R)
No specific
1
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
Page 12 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
B.
C. Referenced Information
REFERENCE
(Ref. 24-42-00-861-001-A).
(Ref. 24-42-00-862-001-A).
(Ref. 25-62-46-400-001-A).
(Ref. 27-50-00-866-008-A).
(Ref. 27-50-00-866-008-A-01).
(Ref. 27-50-00-866-009-A).
(Ref. 27-50-00-866-009-A-01).
(Ref. 33-51-00-710-001-A).
(Ref. 52-30-00-860-001-A).
(Ref. 52-30-00-860-002-A).
DESIGNATION
Energize the Ground Service Network from the External Power
De-energize the Ground Service Network Supplied from the External
Power
Inflation Reservoir, Offwing Escape-Slide - Installation
Extension of the Flaps on the Ground
Extension of the Flaps/Slats on the Ground
Retraction of the Flaps on the Ground
Retraction of the Flaps/Slats on the Ground
Operational Test of the Emergency Lights
Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
Removal of the Wing-to-Fuselage Fairings
Installation of the Wing-to-Fuselage Fairings
(Ref. 53-35-11-000-001-A).
(Ref. 53-35-11-400-001-A).
AIPC 533503
Offwing Escape-Slide Compartment 7504MM (7505MM)
3.
Job Set-up
Subtask 25-62-42-860-050-A
A.
Page 13 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
SAFETIES ALL COMPONENTS OF THE INFLATION SYSTEM IN OPERATION AND
PREVENTS ACCIDENTAL:
- DISCHARGE OF THE INFLATION RESERVOIR
- DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
(a) Make sure that the lockpin assembly (4) is installed in the valve/regulator assembly (3).
(8) In the cockpit:
WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE
YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/
OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
(a) Make sure that the flap/slat control lever is set to the FULL position
(Ref. AMM TASK 27-50-00-866-008) .
(b) Make sure that the LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION (98D27803000000) is
installed on the flap/slat control lever.
(c) Make sure that a WARNING NOTICE(S) is in position on the flap/slat control lever to tell persons
not to operate the flaps.
(9) FOR 7504MM (ESCAPE SLIDE OFFWING L)
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position adjacent to
the panel 193AT.
(10) FOR 7505MM (ESCAPE SLIDE OFFWING R)
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position adjacent to
the panel 194AT.
4.
Procedure
Subtask 25-62-42-210-055-A
A.
Page 14 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
NOTE: If the enclosure door (8) and the ball lock pins (18) are not in the correct position, you must replace the escape slide enclosure (7).
Subtask 25-62-42-420-052-A
B.
Subtask 25-62-42-710-050-A
C.
5.
Do the operational test of the emergency lighting system (Ref. AMM TASK 33-51-00-710-001) .
Close-up
Subtask 25-62-42-410-051-A
A.
Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) In the cockpit:
(a) Remove the LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION (98D27803000000) from the
flap/slat control lever.
(b) Remove the warning notice(s).
(c) Set the flap/slat control lever to the 0 position (Ref. AMM TASK 27-50-00-866-009) .
Page 15 of 16
Customer : CSC
Manual : AMM
Type : A318/A319/A320/A321
Selected applicability : 402-402
Rev. Date : May 01, 2016
25-62-42 PB 401 CONF 00 - SLIDE - ESCAPE,
OFFWING - REMOVAL/INSTALLATION
End of document
Page 16 of 16