Professional Documents
Culture Documents
Process Industry Practices Piping
Process Industry Practices Piping
PIP PN01SD0J01
Piping Material Specification 1SD0J01
Class 150, 316/316L Stainless Steel, 0.000" C.A.
Core: Process
Jacket: Steam
This Practice is subject to revision at any time by the responsible Function Team
and will be reviewed every 5 years. This Practice will be revised, reaffirmed, or
withdrawn. Information on whether this Practice has been revised may be found at
http://www.pip.org.
PIP PN01SD0J01
Piping Material Specification Line Class 1SD0J01
April 2001
SERVICE:
Core: Process
Jacket: 150 psi Steam
150, ASME B16.5a-1998
-20F to 800F
0.000 in.
RATING CLASS:
TEMPERATURE LIMIT:
NOMINAL CORROSION ALLOWANCE:
MATERIAL:
DESIGN CODE:
STRESS RELIEF:
EXAMINATION:
-20 to 100
-29 to 38
200
93
300
149
400
204
500
260
600
316
700
371
800
427
For NPS 1/2 through NPS 12 (Full flange rating per ASME B16.5, Table 2-2.2)
psig
kPag
275
1895
235
1620
215
1480
195
1345
170
1170
140
965
110
760
80
550
400
204
500
260
600
316
700
371
800
427
-20 to 100
-29 to 38
200
93
300
149
For NPS 1 through NPS 14 (Pressure is limited by external pressure on 4 inch sch 10S 316/316L core pipe)
psig
kPag
270
1860
ITEM
PIPE
260
1795
NOTES
01
Core
Jacket
Tubing - Jumper
NIPPLES
251
1730
242
1670
231
1595
ENDS
221
1525
210
1450
199
1370
NPS
SCH/RAT
DESCRIPTION
1/2 3/4
14
6 12
1 14
1/2 3/4
1
40S
10S
40S
10S
0.049 in.
0.065 in.
1/2 2
40S
83
Branch
FITTINGS
02
CORE
Reducer (CONC)
Reducer (ECC)
90 LR ELL
45 LR ELL
Tee
Tee (RED)
Cap
JACKET
Reducer (CONC)
Reducer (ECC)
90 SR ELL
45 SR ELL
Tee
Tee (RED)
Cap
85
85
85
85
85
85
1/2 12
1/2 12
1/2 12
1/2 12
1/2 12
1/2 12
1/2 12
Weld
Weld
Weld
Weld
Weld
Weld
Weld
1 16
1 16
1 16
1 16
1 16
1 16
1 16
Weld
Weld
Weld
Weld
Weld
Weld
Weld
1/2 1
1/2 1
1/2 3/4
1/2 3/4
1/2 3/4
THRD
THRD
SW
Weld
THRD
JUMPER
Union
Connector - Female
Half Coupling
SW Pipet
Plug
Class 3000
Class 300
Class 3000
Page 1 of 3
PIP PN01SD0J01
Piping Material Specification Line Class 1SD0J01
ITEM
VALVES
Gate
Gate
Globe
Swing Check
Plug
Plug
NOTES
NPS
SCH/RAT
ENDS
DESCRIPTION
86
1/2 2
1/2 12
1/2 12
1/2 12
14
68
Class 800
Class 150
Class 150
Class 150
Class 150
Class 150
T/SW
RF
RF
CS body w/ 13 CR trim, HF ST
316 SS body w/ 316 SS trim, FP, w/ jacket
316 SS body w/ 316 SS trim, w/ jacket
316 SS body w/ 316 SS trim, w/ jacket
316 SS body w/ 316 SS trim, PTFE sleeve, w/ jacket
316 SS body w/ 316 SS trim, PTFE sleeve, GO, w/ jacket
1/2 14
1/2 14
1/2 14
1/2 14
1/2 14
1/2 14
1/2 14
1/2 14
1/2 14
1/2 14
Class 150
Class 300
Class 150
Class 300
Class 150
Class 300
Class 150
Class 300
Class 150
Class 300
1/2 14
1/2 14
Class 150
Class 150
1/2 14
1/2 14
Class 300
Class 300
09
09
FLANGES
Slip-On (RED)
Slip-On (RED)
Slip-On
Slip-On
Insert (RED)
Insert (RED)
Insert (NON-RED)
Insert (NON-RED)
Blind
Blind
April 2001
12
84
12, 84
09, 82
09,12, 82
09, 82, 84
09, 12, 82, 84
12
RF
RF
RF
RF
RF
GA08CB200
GA01ST550
GL01ST550
CS01ST550
PL01ST550
PL01ST551
RF
RF
RF
RF
RF
RF
RF
RF
GASKETS
12
12
BOLTING
Stud Bolts
Spiral wound type 316L SS, w/ flexible graphite filler, ASME B16.20
Spiral wound type 316L SS, w/ flexible graphite filler, ASME B16.20,
special reducing flange dimensions
Spiral wound type 316L SS, w/ flexible graphite filler, ASME B16.20
Spiral wound type 316L SS, w/ flexible graphite filler, ASME B16.20,
special reducing flange dimensions
82
90 BRANCH CONNECTION Core vents, drains, and instrument connections only (Note 16)
Legend and Chart
BRANCH SIZE
12
10
1-1/2
3/4
1/2
12
10
1-1/2
3/4
1/2
T
T
T
HEADER SIZE
B
E
T
Branch Weld
Reducing Tee or Tee and Reducer(s)
Tee
Page 2 of 3
PIP PN01SD0J01
Piping Material Specification Line Class 1SD0J01
April 2001
BRANCH SIZE
90 BRANCH CONNECTION Jacket on core branch (to be used with core vent, drain, and instrument connection table)
Legend and Chart
14
12
10
2-1/2
1-1/2
14
12
10
2-1/2
1-1/2
T
T
HEADER SIZE
B
E
P
T
Branch Weld
Reducing Tee or Tee and Reducer(s)
Branch Weld w/ Reinforcing Pad. Pad thickness equals run pipe thickness. Pad width equals 1/2 branch OD.
Tee
NOTES:
01
02
09
12
16
82
83
84
85
86
Core Pipe
Jacket Pipe
1/2
3/4
1
1-1/2
2
2
3
3
4
6
8
10
12
1
1-1/2
2
2-1/2
3
4
4
6
6
8
10
12
14
Special Jacket
Fittings
12-Elbows
14-Elbows
16-Elbows, 16-Tee
Flange Size,
Reducing Jacket
1 x 1/2
1-1/2 x 3/4
2x1
2-1/2 x 1-1/2
3x2
4x2
4x3
6x3
6x4
8x6
10 x 8
12 x 10
14 x 12
Flange Size,
Non-Reducing Jacket
1/2
3/4
1
1-1/2
2
2
3
3
4
6
8
10
12
Supply, Return,
and Jumper
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
Where pipe schedule is shown under SCH/RAT, it is adequate for the full flange rating. Where Calc is shown, the pressure limit may be lower
than flange rating.
All butt welded component thicknesses shall match pipe thickness.
Pressure and temperature rating may be limited by certain components permitted by this specification. Refer to manufacturers recommended
pressure-temperature restrictions.
To be used only to match class 300 rated flange connections at control valves and special equipment.
Core branch connections should consist of tees, reducers, and/or reducing tees except in the case of vents, drains, and instrument connections, where
branch welds are permitted per the branch connection tables.
Stud bolt lengths may be longer due to increased thickness of the insert flange.
Threaded joints are permitted only at jacket jumper and instrument connections. Threaded joints, except tube fittings and instruments, shall be seal
welded.
Use non-reducing flange against equipment or at specification break to piping with non-reducing flange.
Ej = 0.80 when component is split and rewelded.
This valve to be used for jacket vent and drain applications.
REFERENCES:
Process Industry Practices (PIP)
PIP PNF0200 - Vents, Drains, and Instrument Connection Details
PIP PNFJ8000 - Jacketed Pipe Fabrication Details
PIP PNSMV003 - Carbon Steel Gate Valve Descriptions
PIP PNSMV023 - Stainless Steel Gate Valve Descriptions
PIP PNSMV024 - Stainless Steel Globe Valve Descriptions
PIP PNSMV025 - Stainless Steel Check Valve Descriptions
PIP PNSMV028 - Stainless Steel Plug Valve Descriptions
Page 3 of 3