Professional Documents
Culture Documents
User Manual For Base Plate Design Tool:-: Pinned Type Pinned Type
User Manual For Base Plate Design Tool:-: Pinned Type Pinned Type
DD MM YYYY
User manual for base plate design tool:1.0 The workbook contains an excel tool for the design of Base plate connection as per EN 1993-1-8: 2005.
2.0 Following types of connections have been considered in this excel tool. The user is advised to input correct
type of base plate in "DESIGN DATA" sheet.
PINNED TYPE
Type 1
Total No. of bolts = 2
No of Rows = 1
PINNED TYPE
Type 2
Total No. of bolts = 4
Total No of Rows =2
z
FIXED TYPE
Type 3
Total No. of bolts = 2
No of Rows = 1
FIXED TYPE
Type 4
Total no of bolts = 6
Total No of Rows = 2
FIXED TYPE
Type 5
Total no of bolts = 8
Total No of Rows =2
FIXED TYPE
Type 6
Total no of bolts = 8
Total No of Rows = 4
FIXED TYPE
Type 7
Total no of bolts = 16
Total No of Rows =4
FIXED TYPE
Type 8
Total no of bolts = 4
Total No of Rows = 2
Note- This type is not included in
the present sheet.
Report no : SPEL/XX/YYYY/XXX
Sheet 1 of 95
APPENDIX - XX
DD MM YYYY
3.0 This tool can handle x-dir moments only. Bi-axial moment capability is not there at present.
Also the column section profile has to be I or H profile
Input
Output
Comment (except green cells of sheet " REACTIONS")
5.0 Each workbook is divided in many sub sheets for ease. Following is the description of various sheets :
( do not try to rename the sheets as the macro will not recognize the new name)
5a. REACTIONS : This sheet contains reactions data. It is devised in same format as the GTS output so that
minimum editing in GTS output is required. User can directly copy and paste the GTS output into this sheet.
Cases of single load case ( when GTS analysis is not done) may also be handled by this sheet.
(i) Green cells in this sheet are not meant for editing by user. Simply ignore the green colour
(ii) Read the comments carefully in cells A1, B1,C1,D1 and note in cell J7 before starting your design
(iii) For Input loading data please refer to the coordinate axis as shown in REACTIONS sheet. X-axis
must be parallel to column flange width ( parallel to width of base plate). Moment about Z-Z axis of column (as
shown in figure) should be zero for all the load cases.
(iv) Special Precautions have to be taken by the user to ensure correctness of directions of all the
forces and moments while pasting output reactions from GTS to REACTIONS sheet. Design forces
considered by the tool are having opposite sign as REACTIONS sheet . Hence user must enter
reactions and not the forces.
(v) Sign convention used in the sheet is as follows:a. Tension force considered positive.
b. Clockwise moment taken positive.
Note:- Signs mentioned here are for forces and not for reactions. User must not confuse forces with reactions.
(vi) Change value in black cell C1 according to length of data. For example if last load case data is in cell 670
then the value in this cell should be 670-15 = 655. Using this value, single load cases may be handled by
putting cell value as 1. Cells B1 and D1 should not be changed.
(vii) Delete all the data printed in Blue cells before running the macro.
(viii) Please note that this sheet is unprotected. Hence responsibility to ensure no other editing lies with the
user. It is very essential not to change any other cell in this sheet.
5b. DESIGN DATA : In this sheet, all the necessary design inputs are entered. Starting with Type of connaction, followed by column dimensions, material properties, Assumed Base plate dimensions, Anchor bolts
Report no : SPEL/XX/YYYY/XXX
Sheet 2 of 95
APPENDIX - XX
DD MM YYYY
type and properties, Anchor locations, spacings, Anchor plate dimensions, Shear key parameters and stiffener
dimensions etc. Project specific permissible values based on design code may be changed here though it is
Report no : SPEL/XX/YYYY/XXX
Sheet 3 of 95
APPENDIX - XX
DD MM YYYY
not encouraged. Please contact the developer of the workbook for any project specific changes. Note that minimum washer plate dimensions required for selected bolt diameter is obtained in this sheet (refer to cell E520
and E522). These dimensions are to be ensured in the drawings by the engineer.
5c. Calculations : This sheet is used to calculate base plate capacities, Compression capacity, Tension
capacity, Moment Capacity, and bearing capacity. All the calculations done in this sheet are based on
EN 1993-1-8:2005. In some cases DIN codes have also been referred for some calculations.
5d. Weld Design : Weld between column and base plate is being designed in this sheet. Additional moments
generated due to eccentric bracings (Both major axis moment and torsion) are also been handled in this sheet.
5e. Anchor Plate : This sheet is used for anchor plate design. Various checks are incorporated in this sheet
like anchor plate bending check, punching shear check, ETAG etc.
5f. Shear-key : Includes both orientation of shear key. It should be noted that in case of eccentric bracings,
shear key should be kept at center only as all the stresses calculated includes stresses due to additional moments generated as a result of eccentric bracings.
5g . Stiffener design : Stiffener design sheet includes buckling checks for horizontal and vertical directions.
5h . SUMMARY : By pressing the Summary button, a macro gets activated and a design summary is
automatically created for most critical load cases.
STEP 2. While finalizing base plate dimensions, and giving input for Projection of base plate beyond column
edges, user need to check "c" calculation being performed at bottom of the sheet. Here user has to press
"Calculate C" button, and then finalize base plate projections equal to or more than "c" value. This is essential
to provide full compression capacity for that particular base plate. Moreover user should also check that plan
dimensions fixed by him results in "Large Projection Base Plate" in both directions.
STEP 2. After putting in all the inputs, come back to REACTIONS sheet and paste GTS output in empty cells.
Take care to fill appropriate value in cell C1 as explained above.
STEP 4. After one cycle of macro is completed carefully examine the maximum values of results in cells K3
AH3 and compare with permissible values. Check SAFE/UNSAFE status in row 5 of sheet REACTIONS
Report no : SPEL/XX/YYYY/XXX
Sheet 4 of 95
APPENDIX - XX
DD MM YYYY
STEP 5. Identify the areas where changes need to be made for bringing all the calculated values within limits.
Make necessary changes in the input data.
STEP 6. Re-run the macro and repeat Step 5. Keep repeating till the desired level of accuracy
in results are obtained. After running macro each time if user wish to find out critical cases he should press
the button "For highlighting critical values press here" which will highlight maximum values with red colour.
STEP 7. After finalizing base plate design, go to SUMMARY sheet and press button "Summary".
This button initiates a macro which in turn creates a design summary for the most critical load cases. This
sheet can be added to the Report.
STEP 8. After finishing up all design steps(Step 1 to Step 7), User is first required to change Header and footer
settings as per project requirement, and then press button "PRINT" in SUMMARY sheet. This button will
initiate a macro which in turn will take a print of this workbook for report generation purpose. (Note:- Before
pressing "PRINT" button, the user must check his default printer settings by following this path
Control Panel
Printers and Faxes
Here select any of your mapped printer as your default printer by right clicking it. In case User wish to
create .Pdf files, He will have to select "Adobe PDF" as default printer. Before taking a print out, user should
hide "Stiffener design" sheet if stiffeners are not considered in design. This part is not handled by the sheet
automatically.)
Report no : SPEL/XX/YYYY/XXX
Sheet 5 of 95
Report no : SPEL/XX/YYYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 6 of 95
APPENDIX - XX
DD MM YYYY
993-1-8: 2005.
d to input correct
Report no : SPEL/XX/YYYY/XXX
Sheet 7 of 95
APPENDIX - XX
DD MM YYYY
Report no : SPEL/XX/YYYY/XXX
Sheet 8 of 95
APPENDIX - XX
DD MM YYYY
Report no : SPEL/XX/YYYY/XXX
Sheet 9 of 95
APPENDIX - XX
DD MM YYYY
apacity, Tension
. Additional moments
handled in this sheet.
eccentric bracings,
e to additional mo-
d vertical directions.
summary is
AD ME sheet and
based on engineer's
results in cells K3
t REACTIONS
Report no : SPEL/XX/YYYY/XXX
Sheet 10 of 95
APPENDIX - XX
DD MM YYYY
s he should press
lues with red colour.
Report no : SPEL/XX/YYYY/XXX
Sheet 11 of 95
Report no : SPEL/XX/YYYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 12 of 95
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
A
read me
B
16
C
4
D
3
I
9
J
10
Maximum Values
Left
JOINT
50.00
50.00
1000.00
-250.00
Y FORCE
(kN)
50.00
50.00
M
13
N
14
895.59
-2574.90
608.42
484.54
Safe
895.59
X
Comments
Viewing
Direction
L
12
Checks
Permissible and Assumed Values
+Mx
Right
K
11
50.00
-150.00
0.00
0.00
0.00
0.00
Joint Capacity
ECCENT.
(MX/Py)
Type of Connection
Tension
Capacity
KN
50
50
50
50
1000
-250
250
-150
50
50
50
50
50
50
-150
-150
Moment
Capacity
KN-m
Tension
Force
KN
Base Plate
Compression
Capacity
KN
0
0
0
0
0
0
0
0
0.09
-0.37
-0.77
1.29
Pure Compression
Left in Comp. & Right in Tension
Left in Tension & Right in Comp.
Left in Tension & Right in Comp.
895.59
895.59
895.59
895.59
-2574.90
-2574.90
-2574.90
-2574.90
-344.35
-258.96
608.42
357.29
0.00
322.67
284.54
484.54
1
2
3
4
5
6
7
8
O
15
P
16
Q
17
R
18
S
19
T
20
U
21
V
22
W
23
X
24
Y
25
Z
26
AA
27
-697.67
0.42
0.18
52.07
0.22
12.79
0.98
32.68
9.92
0.10
0.07
37.88
18.17
Safe
-2574.90
Safe
1.00
Safe
1.00
Safe
208.00
Safe
0.35
Safe
25.00
Safe
1.00
Safe
129.91
Safe
129.91
Safe
1.00
Safe
1.00
Safe
225.00
Safe
225.00
Steel to steel
bearing
Weld stress
at col-base
interface
N/mm2
2-way shear
stress in
conc
N/mm2
Required
minimum
thickness of
Anchor plate
mm
9
10
11
12
13
Weld
14
15
16
17
18
19
-697.67
-72.67
-534.54
-334.54
0.15
0.19
0.25
0.42
0.18
0.02
0.14
0.08
52.07
33.04
45.46
42.92
Bearing
strength ratio,
x-dir against
concrete
Anchor Plate
0.00
0.15
0.13
0.22
0.00
10.44
9.80
12.79
Bearing
strength ratio,
z-dir against Bending stress Bending stress
concrete
-x in key
-z in key
2
N/mm
N/mm2
Shear Key
0.00
0.65
0.57
0.98
32.68
32.68
32.68
32.68
9.92
9.92
9.92
9.92
0.10
0.10
0.10
0.10
0.07
0.07
0.07
0.07
37.88
37.88
37.88
37.88
18.17
18.17
18.17
18.17
1
2
3
4
5
6
7
8
AB
28
AC
29
AD
30
AE
31
AF
32
AG
33
AH
34
0.25
173.32
40.38
100.95
122.81
0.30
0.60
Safe
1.00
Safe
208.00
Safe
129.91
Safe
225.00
Safe
225.00
Safe
1.00
Safe
1.00
Vertical
Buckling
force/Buckling
Resistance
Horizontal
Buckling
force/Buckling
Resistance
9
10
11
12
Interaction
check
13
Sum of all
weld stresses Shear Stress
N/mm2
N/mm2
Tensile
Stress
N/mm2
Stiffener
14
15
16
17
18
19
Combined
Stress
N/mm2
0.25
0.25
0.25
0.25
173.32
173.32
173.32
173.32
36.34
26.89
27.84
40.38
90.84
67.22
69.60
100.95
110.51
81.78
84.67
122.81
0.30
0.03
0.23
0.14
0.54
0.40
0.41
0.60
AI
Row no.
out of
AJ
AK
19
19
APPENDIX - XX
DD MM YYYY
Input Data
Enter Type of connection
7
x xx
zz z z
Row
Row111
Row
Row
Row
Row4414
4
100
30 Thk
Plate
200.00
100
Row 1
350
Row 2
HEB500
x
900
122
Row 3
16 x M30 Bolts
Row 4
800
z
25 Thk
Plate
x = 60
120
w = 200
x' = 60
720
Report no : SPEL/XX/YYYY/XXX
Sheet 16 of 95
APPENDIX - XX
COLUMN SECTION
1
depth of section ( d ) =
web thickness (tw) =
width of section ( b ) =
flange thkness ( tf ) =
Root radius
(r) =
Area
Rolled
Built-up
890.00 mm
500.00 mm
14.50 mm
16.00 mm
300.00 mm
300.00 mm
28.00 mm
30.00 mm
30.00 mm
27.00 mm
23864 sq.mm 23864 sq.mm
MATERIAL PROPERTEIS
Concrete grade used in RCC pedestal
Compressive strength of concrete fck,cube =
fck
=
Modulus of elasticity, Steel
Fy
Fu
=
=
Bolt Parameters
=
=
=
af =
m1
m2
1.25
=
=
tww =
(cube strength )
(cylindrical strength )
S235
215 N/mm2
340 N/mm2
215 N/mm2
S235
225 N/mm2
360 N/mm2
225.0 N/mm2
129.9 N/mm2
twf =
12
Additional force to be considered in weld design :
Maximum axial force in vertical bracing P =
Report no : SPEL/XX/YYYY/XXX
C25/30
30 N/mm2
25 N/mm2
20500 N/mm2
mo
Weld Parameters
Tensile strength of filler material f u
DD MM YYYY
(read me)
680 N/mm2
544 N/mm2
360 N/mm2
208 N/mm2
a
t
8.49 mm
16.97 mm
200 kN
(read me)
Sheet 17 of 95
APPENDIX - XX
=
=
DD MM YYYY
30 degrees
250 mm
50 mm
1000 mm
200 mm
250 mm
900 mm
800 mm
(read me)
1000 mm af2 =
1000 mm bf2 =
2900 mm
2800 mm
j x FRdu/(beff x Leff)
24.73 N/mm2
30 mm
51.07 mm
1000 mm
1000 mm
M30 mm
561.00 mm2
No. of bolts in row 1 and 4
4
No. of bolts in row 2 and 3
4
Total No. of bolt rows horizontally
4
Distance of row 1 and 4 from centre line
350 mm
Distance of row 2 and 3 from centre line
122 mm
Edge distance along x-dir
100 mm
Bolt Hole Dia
60 mm
Edge Distance along z-dir
100 mm
Bolt spacing, x-Dir
200.00 mm
Bolts outside the Flange, Hence Flange Stiffners are Required
Washer Thickness
20 mm
Height of Nut
30 mm
Washer Width
110 mm
Report no : SPEL/XX/YYYY/XXX
1
25 mm
48 mm
60 mm
60 mm
0.00 mm
200.00 mm
600 mm
1820 mm
0.35 N/mm2
1.8
1.0
Sheet 18 of 95
APPENDIX - XX
DD MM YYYY
Shear Key
Orientation of Shear key
Weld,
as =
1 Shown in Fig
6
tws =
depth of section ( d ) =
web thickness (tw) =
width of section ( b ) =
flange thkness ( tf ) =
Root radius
(r) =
=
8.49 mm
Contact length L
1 (1-Yes,2-No)
Rolled
Built Up
180.00 mm
500.00 mm
8.50 mm
20.00 mm
180.00 mm
300.00 mm
14.00 mm
40.00 mm
15.00 mm
.00 mm
300 mm
250 mm
=
Shear Keyxbelow Baseplate
x
z
ORIENTATION z
: TYPE 1
Report no : SPEL/XX/YYYY/XXX
BASE PLATE
tg
x
z
ORIENTATION : TYPE 2
GROUT
Sheet 19 of 95
APPENDIX - XX
DD MM YYYY
Stiffener Design
Stiffener requirement, moment considerations
Stiffener provided, compression resistance
Stiffener plate thickness assumed,ts =
Stiffener plate height assumed,Hs =
=
CALCULATION OF PERMISSIBLE BEARING STRESS
bf1
1 (1-Yes,2-No)
1 (1-Yes,2-No)
20 mm
300 mm
1.2
Pedestal
Base plate
ap
bfooting
bp
af1
af2
a
bf2
Pedestal length = afooting
=
=
4.95
2/3
fcd = fck/c =
16.67 N/mm2
= j x FRdu/(beff x Leff)
fjd
Trial Values
24.73 N/mm2
ctrial
51.07 mm
NO OVERLAP
beff
2 x c + tf
130.13 mm
Leff
2 x c + bf
402.13 mm
=
b1
L1
Actual Area, Ac1
Calculated Values
FRdu
=
390.40 mm
662.40 mm
Report no : SPEL/XX/YYYY/XXX
52331.28 mm2
Clause: 6.7, EN 1992-1-1:2004
258602.89 mm2
1939246.2 N
Sheet 20 of 95
APPENDIX - XX
fjd
=
ccalculated =
Report no : SPEL/XX/YYYY/XXX
DD MM YYYY
24.70 N/mm2
51.10 mm
Sheet 21 of 95
Report no : SPEL/XX/YYYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 22 of 95
APPENDIX - XX
DD MM YYYY
Report no : SPEL/XX/YYYY/XXX
Sheet 23 of 95
APPENDIX - XX
DD MM YYYY
x
e
7) EN 1993-1-8 :2005)
7) EN 1993-1-8 :2005)
N 1992-1-1 :2004)
Report no : SPEL/XX/YYYY/XXX
Sheet 24 of 95
APPENDIX - XX
DD MM YYYY
BASE PLATE
Report no : SPEL/XX/YYYY/XXX
Sheet 25 of 95
APPENDIX - XX
DD MM YYYY
7), EN 1993-1-8:2005
EN 1992-1-1:2004
N 1992-1-1:2004
Report no : SPEL/XX/YYYY/XXX
Sheet 26 of 95
APPENDIX - XX
DD MM YYYY
4), EN 1993-1-8:2005
Report no : SPEL/XX/YYYY/XXX
Sheet 27 of 95
APPENDIX - XX
DD MM YYYY
leff leff
ceff
c c
ex
abca1ba ZcZ1
ccc cw
mx Fm2
leffcleff
cc1 cc2cw
1cC,l
b
eZ
w
lbeff
m
eff
FTeTe1
leff
eff
Zc,r
Zc,r
ZZ3cc3
ZT,l
e
lb
eff
Zc,r
c c c2c2leff
C,lC,l
m c blZZeff
cT,l
T,l
3
l l LL mZ23T,rT,rT,r3
Axial load P
Row no.
19
150 kN
Mzz =
Hz =
0 kN-m
-50 kN
Mxx =
Moment about x-axis
Hx =
Shear in x-direction
Additional Moment due to eccentric bracing
Mxx =
Total Moment
150 kN-m
-50 kN
43.30 kN-m
193.301 kN-m
=
=
236.00 mm
472.00 mm
-334.54 kN
ZC,l
Zc,r
484.54 kN
ZT,l
ZT,r
L
l
leff
For Stub 1 and 3:
Bearing Area
For Stub 2:
Bearing Area
Nj,Rd
104107.16 mm2
c
c
104107.16 mm2
0 mm
2574.90 kN
Report no : SPEL/XX/YYYY/XXX
514.35 mm
ab
beff
Sheet 28 of 95
APPENDIX - XX
beff
DD MM YYYY
0.60
=
1012.91 kN
leff
Report no : SPEL/XX/YYYY/XXX
Sheet 29 of 95
APPENDIX - XX
DD MM YYYY
Ft,pl,,Rd :
Method 1
For bolts outside flanges
ex
=
Clause:6.2.4, EN 1993-1-8:2005
100 mm
mx
e
n
=
= min(emin,1.25m)
w
leff,cp
=
=
871.51 mm
leff,nc
400.00 mm
leff,1
= min(leff,cp , leff,nc )
400.00 mm
leff,2
= leff,nc
400.00 mm ex
86.42 mm
100.00 mm
=
Lb
Lb*
= (8.8xm3xAs)/leff,1xtp3) =
100.00 mm
200.00 mm
ex
mx
mx
355 mm
295.07 mm
No Prying Forces
Therefore,
Mpl,1,Rd =
0.25leff,1xtp2*fy/mo =
19.35 kNm
Mpl,2,Rd =
0.25leff,2xtp2*fy/mo =
19.35 kNm
Ft,Rd
274.67 kN
Ft,1,Rd
4Mpl,1,Rd/m
Ft,2,Rd
(2Mpl,2,Rd+nFt,Rd)/(m+n)
Ft,1-2,Rd
Ft,3,Rd
=
=
= 2Mpl,1,Rd/m
=
Ft,Rd
=
=
796.93 kN
447.79 kN
1098.66 kN
Ft,pl,,Rd = min(Ft,1,Rd,Ft,2,Rd,Ft,3,Rd)
895.59 kN
447.79 kN
86.42 mm
86.42 mm
100.00 mm
e
n
w
leff,cp
=
= min(emin,1.25m)
=
=
leff,nc
400.00 mm
leff,1
= min(leff,cp , leff,nc )
400.00 mm
leff,2
= leff,nc
400.00 mm
86.42 mm
200.00 mm
871.51 mm
Lb
355 mm
Lb*
= (8.8xm3xAs)/leff,1xtp3) =
0.53 mm
No Prying Forces
Therefore,
Mpl,1,Rd =
0.25leff,1xtp2*fy/mo =
19.35 kNm
Mpl,2,Rd =
0.25leff,2xtp2*fy/mo =
19.35 kNm
Report no : SPEL/XX/YYYY/XXX
Sheet 30 of 95
APPENDIX - XX
Ft,Rd
274.67 kN
Ft,1,Rd
4Mpl,1,Rd/m
Ft,2,Rd
(2Mpl,2,Rd+nFt,Rd)/(m+n)
Ft,1-2,Rd
Ft,3,Rd
= 2Mpl,1,Rd/m
=
Ft,Rd
DD MM YYYY
=
=
Report no : SPEL/XX/YYYY/XXX
895.59 kN
773.23 kN
447.79 kN
1098.66 kN
Sheet 31 of 95
APPENDIX - XX
Ft,pl,,Rd = min(Ft,1,Rd,Ft,2,Rd,Ft,3,Rd)
Total Ft,pl,,Rd for all bolts =
Ft,pl,,Rd :
DD MM YYYY
447.79 kN
895.59 kN
Method 2
T-Stub 1
ex
=
mx
100.00 mm
86.42 mm
100.00 mm
e
n
w
leff,cp
=
= min(emin,1.25m)
=
=
leff,nc
335.35 mm
leff,1
= min(leff,cp , leff,nc )
335.35 mm
leff,2
= leff,nc
335.35 mm
ex
100.00 mm
200.00 mm
mx
471.51 mm
Lb
Lb*
= (8.8xm3xAs)/leff,1xtp3) =
mx
355 mm
2 m2
188.21 mm
No Prying Forces
Therefore,
Mpl,1,Rd =
0.25leff,1xtp2*fy/mo =
16.22 kNm
Mpl,2,Rd =
0.25leff,2xtp2*fy/mo =
16.22 kNm
Ft,Rd
274.67 kN
Ft,1,Rd
4Mpl,1,Rd/m
Ft,2,Rd
(2Mpl,2,Rd+nFt,Rd)/(m+n)
Ft,1-2,Rd
Ft,3,Rd
=
=
= 2Mpl,1,Rd/m
=
Ft,Rd
=
=
750.83 kN
468.71 kN
375.42 kN
549.33 kN
Ft,pl,,Rd = min(Ft,1,Rd,Ft,2,Rd,Ft,3,Rd)
375.42 kN
T-Stub 2
Ft,pl,,Rd for T-Stub 2 is same as calculated in Method 3 below.
Ft,pl,,Rd =
796.93 kN
T-Stub 3
m
e
n
w
m2
1
=
=
= min(emin,1.25m)
=
=
=
85.96 mm
100.00 mm
=
100.00 mm
200.00 mm
86.42 mm
0.46
leff,cp
540.11 mm
leff,nc
514.35 mm
leff,1
= min(leff,cp , leff,nc )
514.35 mm
=
=
Report no : SPEL/XX/YYYY/XXX
0.46
5.98
Sheet 32 of 95
leff,2
= leff,nc
APPENDIX - XX
514.35 mm
Lb
355.00 mm
Lb*
= (8.8xm3xAs)/leff,1xtp3) =
225.81 mm
No Prying Forces
DD MM YYYY
Therefore,
Report no : SPEL/XX/YYYY/XXX
Sheet 33 of 95
APPENDIX - XX
Mpl,1,Rd =
0.25leff,1xtp2*fy/mo =
24.88 kNm
Mpl,2,Rd =
0.25leff,2xtp2*fy/mo =
24.88 kNm
Ft,Rd
Ft,1,Rd =
Ft,2,Rd =
Ft,1-2,Rd =
Ft,3,Rd =
274.67 kN
4Mpl,1,Rd/m
(2Mpl,2,Rd+nFt,Rd)/(m+n)
2Mpl,1,Rd/m
Ft,Rd
=
=
=
=
Ft,pl,,Rd = min(Ft,1,Rd,Ft,2,Rd,Ft,3,Rd,Ft,wc,Rd) =
1721.68 kN
leff,cp
leff,nc
leff,1
leff,2
Lb
Lb*
1157.81 kN
563.00 kN
578.90 kN
549.33 kN
549.33 kN
Ft,pl,,Rd :
DD MM YYYY
e1
From Table 6.6, EN 1993-1-8:2005
86.42 mm
100.00 mm
100.00 mm
100 mm
200.00 mm
85.96 mm
0.46
0.46
5.98
400.00 mm
200.00 mm
200.00 mm
200.00 mm
355 mm
590.13 mm
=
=
=
=
=
=
=
= min(leff,cp , leff,nc )
= leff,nc
=
= (8.8xm3xAs)/leff,1xtp3) =
e
1
m
m2
leff
Therefore,
Mpl,1,Rd =
Mpl,2,Rd =
Ft,Rd
0.25leff,1xtp2*fy/mo =
0.25leff,2xtp2*fy/mo =
=
Ft,1,Rd
4Mpl,1,Rd/m
Ft,2,Rd
(2Mpl,2,Rd+nFt,Rd)/(m+n)
Ft,1-2,Rd
Ft,3,Rd
=
=
= 2Mpl,1,Rd/m
=
Ft,Rd
=
=
Ft,pl,,Rd = min(Ft,1,Rd,Ft,2,Rd,Ft,3,Rd)
Report no : SPEL/XX/YYYY/XXX
9.68 kNm
9.68 kNm
274.67 kN
447.79 kN
398.46 kN
223.90 kN
549.33 kN
398.46 kN
Sheet 34 of 95
APPENDIX - XX
796.93 kN
471.51 mm
leff,nc
381.78 mm
leff,1
= min(leff,cp , leff,nc )
381.78 mm
Report no : SPEL/XX/YYYY/XXX
DD MM YYYY
Sheet 35 of 95
APPENDIX - XX
leff,2
= leff,nc
Lb
381.78 mm
Lb*
DD MM YYYY
355 mm
= (8.8xm3xAs)/leff,1xtp3) =
309.15 mm
No Prying Forces
Therefore,
Mpl,1,Rd =
0.25leff,1xtp2*fy/mo =
18.47 kNm
Mpl,2,Rd =
0.25leff,2xt *fy/mo =
18.47 kNm
Ft,Rd
2
p
274.67 kN
Ft,1,Rd
4Mpl,1,Rd/m
Ft,2,Rd
(2Mpl,2,Rd+nFt,Rd)/(m+n)
Ft,1-2,Rd
Ft,3,Rd
=
=
= 2Mpl,1,Rd/m
=
Ft,Rd
854.80 kN
492.80 kN
427.40 kN
Ft,pl,,Rd = min(Ft,1,Rd,Ft,2,Rd,Ft,3,Rd)
549.33 kN
=
427.40 kN
854.80 kN
1651.72 kN
FT,Rd
895.59 kN
Fc,pl,Rd
Fc,fc,,Rd :
Hence
Design Compression Resistance, FC,Rd
2574.90 kN
357.29 kNm
357.29 kNm
Report no : SPEL/XX/YYYY/XXX
Sheet 36 of 95
APPENDIX - XX
DD MM YYYY
-517.49 kNm
1487.82 kNm
357.29 kNm
Mj,Rd
Tension Capacity
Compression Capacity
Moment Capacity
Bearing capacity
=
=
18400.0 mm2
3956.00 kN
Design Summary
895.59 Tension Force
-2574.90 Compression force
357.29 Moment
-3956.00 Compression force
Report no : SPEL/XX/YYYY/XXX
484.54
-697.67
193.30
-697.67
Ratio
0.54
0.27
0.54
0.18
Safe
Safe
Safe
Safe
Sheet 37 of 95
APPENDIX - XX
DD MM YYYY
beff
beff
beff
cleff
eff
beff Z33wc 3c3cFcFce cb
b
eff
3
T,r
ex
mx
Fc
ZT,r
5, EN 1993-1-8:2005
beff
6.3, EN 1993-1-8:2005
Report no : SPEL/XX/YYYY/XXX
Sheet 38 of 95
Report no : SPEL/XX/YYYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 39 of 95
APPENDIX - XX
DD MM YYYY
, EN 1993-1-8:2005
6.6, EN 1993-1-8:2005
leff
leff
6.2, EN 1993-1-8:2005
6.6, EN 1993-1-8:2005
6.2, EN 1993-1-8:2005
Report no : SPEL/XX/YYYY/XXX
Sheet 40 of 95
Report no : SPEL/XX/YYYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 41 of 95
APPENDIX - XX
DD MM YYYY
6.6, EN 1993-1-8:2005
leff
leff
6.2, EN 1993-1-8:2005
6.6, EN 1993-1-8:2005
Report no : SPEL/XX/YYYY/XXX
Sheet 42 of 95
APPENDIX - XX
DD MM YYYY
6.2, EN 1993-1-8:2005
Report no : SPEL/XX/YYYY/XXX
Sheet 43 of 95
APPENDIX - XX
DD MM YYYY
6.6, EN 1993-1-8:2005
leff
6.2, EN 1993-1-8:2005
Report no : SPEL/XX/YYYY/XXX
Sheet 44 of 95
Report no : SPEL/XX/YYYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 45 of 95
APPENDIX - XX
DD MM YYYY
6.7 EN 1993-1-8:2005
Report no : SPEL/XX/YYYY/XXX
Sheet 46 of 95
Report no : SPEL/XX/YYYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 47 of 95
APPENDIX - XX
DD MM YYYY
150 kN
Mzz =
Hz =
0 kN-m
-50 kN
Mxx =
Hx =
150 kN-m
-50 kN
200 kN
30 degrees
250 mm
depth of section D =
thickness of flange tf =
500 mm
28 mm
27 mm
root radius
r =
width of flange bf =
300 mm
14.5 mm
8.5 mm
17.0 mm
250 mm
2927.235498 mm
780 mm
weld
weld
3707.235498 mm
=
2013053494 mm4
2x0.7xtwfx[((bf-2twf)3)/12+(2*((bf-twb-2twf-2r)/2)3)/12 + 2x((bf-twb-2twf-2r)/2)*(twb/2 +r + (bf-twb-2twf-2r)/4)2]
=
1779525406 mm4
4.31 N/mm2
10.79 N/mm2
24.01 N/mm2
0.00 N/mm2
Due to P, fa = (P/(0.7xtwxLw)
3.81 N/mm2
42.92 N/mm2
208 N/mm2
SAFE
Weld Thickness check (Cl 519,DIN18800-1, Cl 6.2.2.8, DIN 15018-2, Cl 4.5.2(2) EN 1993-1-8 :2005)
On Web
minimum weld thickness at any place
minimum weld thickness on web
maximum weld thickness on web
Report no : SPEL/XX/YYY/XXX
4.2 mm
7.0 mm
14.5 mm
Sheet 48 of 95
APPENDIX - XX
Report no : SPEL/XX/YYY/XXX
DD MM YYYY
8 mm
4.2 mm
7.1 mm
28 mm
8 mm
Sheet 49 of 95
APPENDIX - XX
DD MM YYYY
P
x
/2 +r + (bf-twb-2twf-2r)/4)2]
Report no : SPEL/XX/YYY/XXX
Sheet 50 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 51 of 95
APPENDIX - XX
DD MM YYYY
200.00 mm
0.00 mm
60 mm
60 mm
120 mm
720 mm
484.54 KN
242.27 kN
4 nos.
1 nos.
30 mm
32 mm
600 mm
1820 mm
0.22 N/mm2 <
SAFE
60 mm
3634024.42 Nmm
12.79 mm
1345934.97 Nmm
7.79 mm
2.80 N/mm2
88 mm
592 mm
=
=
Report no : SPEL/XX/YYY/XXX
0.35 N/mm2
225.0 N/mm2
259.2 N/mm2
2.66
1.58
12.794 mm
Thickness sufficient
25 mm
Sheet 52 of 95
APPENDIX - XX
DD MM YYYY
ha
le =hef
1000 mm
=
dnom
Diameter of anchor bolt
Total number of bolts resisting tension,n
number of bolts in direction-1
30 mm
8
n1
n2
number of bolt in direction-2
spacing between anchor bolts in direction 1
s1,1
200.00 mm
s1,2
200.00 mm
s1,3
200.00 mm
Sum s1=
600.00 mm
Ca1
S
1
600 mm
Sum s2=
2
spacing between anchor bolts in direction 2
s2,1
228 mm
0
0
228 mm
Ca1
1.5hef
Dir-1
S1
S1a
Ca
S2 2
Ca2
S2a
Ac,N
S2
1.5hef
Dir-2
ha
S1a,1 =
0 mm
S1a,2 =
Ca1,1 =
1100 mm
Ca1,2 =
1100
Ca1,1 =
940 mm
Ca1,2 =
940
Ca'1,1 =
940 mm
Ca'1,2 =
940
S2a,1 =
0 mm
S2a,1 =
Ca2,1 =
1100 mm
Ca2,2 =
1100
Ca2,1 =
940 mm
Ca2,2 =
940
Ca'2,1 =
940 mm
Ca'2,2 =
940
NA
Ca2,2 =
Ca1,1 =
Report no : SPEL/XX/YYY/XXX
NA
Ca1,2 =
0
NA
Ca2,1 =
Sheet 53 of 95
APPENDIX - XX
h'ef
DD MM YYYY
600.00 mm
Report no : SPEL/XX/YYY/XXX
1.8
Sheet 54 of 95
APPENDIX - XX
DD MM YYYY
9h'ef2
3441025 mm2
{Ca'1,1+S1,i+Ca'1,2 }*{Ca'2,1+S2,i+Ca'2,2 }
Ac,N=
5227840.0
mm2
7.2h'ef1.5fck,cube
NoRk,c =
579588.8
ec,N =
1/(1+(2*e'N)/(Scr,N))1
0.00 (eccentricity
in the connection-Direction1)
0.00 (eccentricity in the connection-Direction2)
e'N=
e'N=
ec,N,1 =
1.000
ec,N,2 =
1.00
re,N =
0.5+(hef/200)1
re,N =
s,N =
1.00
0.7 + 0.3*(Ca,min/1.5h'ef) 1
s,N =
ucr,N =
1.013
1.0
for locations where concrete cracking is likely to occur (i.e., the edge of the foundation)
NRk,c =
892.29 KN
NRd,c =
495.72 KN
Report no : SPEL/XX/YYY/XXX
Nsd
484.54 KN
Safe
Sheet 55 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 56 of 95
APPENDIX - XX
DD MM YYYY
mm
mm
mm
mm
mm
mm
mm
mm
NA
Report no : SPEL/XX/YYY/XXX
Sheet 57 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 58 of 95
APPENDIX - XX
DD MM YYYY
n cracked concrete, N b
Report no : SPEL/XX/YYY/XXX
Sheet 59 of 95
APPENDIX - XX
DD MM YYYY
Hz
Hz
Hx
Hx
x
x
x
ORIENTATION : TYPE 1
ORIENTATION : TYPE 2
BASE PLATE
Hz,KEY
tg
Hx,KEY
X
Z
DIRECTIONS CONSIDERED FOR
SHEAR KEY
L
SECTION THROUGH SHEAR KEY
Shear force Hz =
-50 kN
MODIFIED FORCE DIRECTIONS BASED ON ORIENTATION OF KEY :
Shear force Hx,KEY =
Shear force Hz,KEY =
-50 kN
Shear force in Single flange including the effect of torsion H z,KEY,f
Additional force to be considered in weld design :
Maximum axial force in vertical bracing P =
bracing angle with vertical axis of column =
eccentricity w.r.t. column centre line
e =
Section Size
Class of Section
Contact length L =
width of flange bf =
thkness of flange tf =
elastic modulus
W elx
Plastic modulus
W plx
root radius
r =
depth of section D =
Depth of web, d =
thickness of web twb =
Report no : SPEL/XX/YYY/XXX
-50 kN
-50 kN
-25.00 kN
(read me)
0 kN
0 degrees
0 mm
HEB180
1 (See calculations below)
250 mm
180 mm
14 mm
151427.32 mm3
231012.4 mm3
15 mm
180 mm
122 mm
8.5 mm
Sheet 60 of 95
Sectional area, A =
Grout thickness tg =
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
6525.14 mm2
50 mm
Sheet 61 of 95
APPENDIX - XX
elastic modulus
W elz
425683.19 mm3
Plastic modulus
W plz
481448.59 mm3
13628459 mm4
38311487 mm4
Torsional constant, IT =
423000 mm4
Warping constant, Iw =
9.37E+010 mm6
45.70 mm
76.62 mm
1530 mm2
DD MM YYYY
2520 mm2
32.68 N/mm2
129.91 N/mm2
Safe
<=
9.92 N/mm
129.91 N/mm2
Safe
11831.25 mm2
25662.5 mm2
>=
484.74 kN
50.00 kN
Safe
>=
335.22 kN
25.00 kN
Safe
34200 mm2
107125 mm2
>=
793.52 kN
50.00 kN
Safe
>=
477.49 kN
25.00 kN
Safe
0.00
0.00
Report no : SPEL/XX/YYY/XXX
Sheet 62 of 95
APPENDIX - XX
DD MM YYYY
8.75 kN-m
Report no : SPEL/XX/YYY/XXX
Sheet 63 of 95
APPENDIX - XX
Mx = Hz,KEY(L/2 + tg)=
DD MM YYYY
8.75 kN-m
Mx/W x=
<=
Mz/W z=
<=
37.88 N/mm2
225.00 N/mm2
Safe
18.17 N/mm2
225.00 N/mm2
Safe
Mcx,Rd =
51.98 kNm
Mcz,Rd =
108.33 kNm
1.00
1.00
Conservatively, =
=
[Mx,Ed / MN,x,Rd] + [Mz,Ed / MN,z,Rd]
0.25
1.0
<=
Safe
kxx
Mx,Ed
+ kxz
LT Mx,Rk
M1
kzx
Mz,Ed
Mz,Rk
M1
Mx,Ed
+ kzz
LT Mx,Rk
M1
Mz,Ed
Mz,Rk
M1
0.196
<=
1.0
0.164
<=
1.0
Safe
Safe
tws
8.4852814 mm
575.11775
2x( D-2tf-2r) ] =
Izz weld =
244 mm
2x0.7xtwsx[ {(D-2tf-2r)3/12}+ (bf-2tws)(D/2)2 + (bf-twb-2tws-2r)x{(D-2tf)/2}2 ]
Ixx
=
24775696 mm4
2x0.7xtwsx[(bf-2tws) /12+(2*((bf-twb-2tws-2r)/2)3)/12 + 2x((bf-twb-2tws-2r)/2)*(twb/2 + r+(bf-twb-2tws-2r)/4)2]
weld
8522594.9 mm4
34.50 N/mm2
14.64 N/mm2
Report no : SPEL/XX/YYY/XXX
92.40 N/mm2
Sheet 64 of 95
APPENDIX - XX
DD MM YYYY
Report no : SPEL/XX/YYY/XXX
31.79 N/mm2
Sheet 65 of 95
APPENDIX - XX
173.32 N/mm2
208 N/mm2
<=
DD MM YYYY
Safe
Report no : SPEL/XX/YYY/XXX
4.2 mm
7.1 mm
8.50 mm
=
8 mm
Sheet 66 of 95
APPENDIX - XX
DD MM YYYY
BASE PLATE
GROUT
SHEAR KEY
Report no : SPEL/XX/YYY/XXX
Sheet 67 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 68 of 95
APPENDIX - XX
DD MM YYYY
993-1-1:2005 (E)
Report no : SPEL/XX/YYY/XXX
Sheet 69 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 70 of 95
APPENDIX - XX
DD MM YYYY
EN 1993-1-1:2005 (E)
N 1993-1-1:2005 (E)
+ r+(bf-twb-2tws-2r)/4)2]
Report no : SPEL/XX/YYY/XXX
Sheet 71 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 72 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 73 of 95
APPENDIX - XX
DD MM YYYY
3
b
Hs
2
1
bs
Plan
Stiffener plate thickness assumed
ts
assumed
Hs
bs =
20 mm
(B-b)/2
300 mm
250 mm
TENSION
Elevation
COMPRESSION
-334.54 kN
Due to effective contact surface between column flange and base plate, above
compression value is shared by column flange and two stiffeners in proportion
to their contact lengths.
Contact length of column flange , b =
Contact length of stiffner plate, bs =
300 mm
250 mm
m1
242.27 kN
t 4 x bs / 2 =
30.28 kN-m
6m1 /H2s x ts
<=
100.95 N/mm2
225.00 N/mm2
SAFE
122.81 N/mm2
<=
Report no : SPEL/XX/YYY/XXX
40.38 N/mm2
129.91 N/mm2
SAFE
225.00 N/mm2
SAFE
( = fy/1)
Sheet 74 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 75 of 95
APPENDIX - XX
DD MM YYYY
208 N/mm2
SAFE
In Vertical plane
(Hs/ts) (72/)
1.2
0.5
Ac
Ac,effect
where
ts x b s =
5000
4830.82035 mm2
(Hs/ts)/(28.4 x K) =
K
=
if p 0.748
if p > 0.748
In this case,
0.79
0.43
1
(p -0.188) / p2 1
=
hence
x Aeff x fy /M1
=
0.97
0.97
=
0.49 for plates
0.5 x [1 + 0.49 x (0.79 - 0.2) + 0.79^2]
=
0.95
1 / ( + (2 - p2) )
2
p
=
Hence, =
Therefore buckling resistance of stiffener
Nb.Rd
x Ac x fy / M1 =
=
727.83 kN
Since compression < Nb.Rd hence, stiffener is safe in buckling
2)
In Horizontal plane
In horizontal plane buckling strength calculations are done in similar manner by replacing
bs with Hs in above calculations
(bs/ts) (72/)
Report no : SPEL/XX/YYY/XXX
1.2
Clause:5.1, EN 1993-1-5
Sheet 76 of 95
and
0.5
'' = (235/fy) =
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
1.02198065
Sheet 77 of 95
APPENDIX - XX
bs/ts
=
12.5
72/
=
61.3188389
Since, (Hs/ts) (72/), No Shear buckling .
Aeffect = Ac
Ac
Aeffect
ts x Hs =
(bs/ts)/(28.4 x K
K
where
=
if p > 0.748
In this case,
Buckling resistance of stiffener,
Nb.Rd
x A x fy /M1
=
0.66
0.43
1
(p -0.188) / p2 1
=
hence
1.00
1.00
From Cl.6.3.1.1 of EN 1993-1-1
For class 1,2 and 3 crossections
x Aeff x fy /M1
6000
6000 mm2
if p 0.748
DD MM YYYY
=
0.75 but 1.0
0.75
Hence, =
Therefore buckling resistance of stiffener
Nb.Rd
x Ac x fy / M1 =
=
1014.19 kN
compression at face 2 of stiffener = 2,t xtsxHs =
605.67 kN
Since compression < Nb.Rd hence, stiffener is safe in buckling
Report no : SPEL/XX/YYY/XXX
Sheet 78 of 95
APPENDIX - XX
DD MM YYYY
bs/2
m1
COMPRESSION
Report no : SPEL/XX/YYY/XXX
Sheet 79 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 80 of 95
APPENDIX - XX
DD MM YYYY
6.2.6.(6) EN1993-1-1
4.4(1), EN 1993-1-5
4.4(2) , EN 1993-1-5
1.1 of EN 1993-1-1
and 3 crossections
1.2 of EN 1993-1-1
6.2.6.(6) EN1993-1-1
Report no : SPEL/XX/YYY/XXX
Sheet 81 of 95
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 82 of 95
APPENDIX - XX
DD MM YYYY
4.4(1), EN 1993-1-5
4.4(2) , EN 1993-1-5
4.2, EN 1993-1-5
1.1 of EN 1993-1-1
and 3 crossections
1.2 of EN 1993-1-1
Report no : SPEL/XX/YYY/XXX
Sheet 83 of 95
APPENDIX - XX
DD MM YYYY
LOAD CASE
X FORCE
(kN)
Y FORCE
(kN)
Z FORCE
(kN)
X MOMENT
(kN-m)
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
2
3
3
3
3
2
2
2
1
3
1
3
3
1
3
3
3
3
3
3
3
-4.50
22.90
22.90
22.90
22.90
-4.50
-4.50
-4.50
34.90
22.90
34.90
22.90
22.90
34.90
22.90
22.90
22.90
22.90
22.90
22.90
22.90
-250.00
947.00
947.00
947.00
947.00
-250.00
-250.00
-250.00
1000.00
947.00
1000.00
947.00
947.00
1000.00
947.00
947.00
947.00
947.00
947.00
947.00
947.00
-115.60
150.00
150.00
150.00
150.00
-115.60
-115.60
-115.60
67.90
150.00
67.90
150.00
150.00
67.90
150.00
150.00
150.00
150.00
150.00
150.00
150.00
200.00
420.00
420.00
420.00
420.00
200.00
200.00
200.00
-124.30
420.00
-124.30
420.00
420.00
-124.30
420.00
420.00
420.00
420.00
420.00
420.00
420.00
Ratio
Maximum Values
Tension
Compression
Base plate
Moment
Bearing
Weld B/W Column & Base plate
Twoway Shear stress
Anchor Plate
Shear key
Stiffener
Combined Stresses
Vertical buckling
Horizontal Bucking
Report no : SPEL/XX/YYY/XXX
0.61
0.53
0.31
0.34
0.48
0.20
0.62
1.75
0.11
0.14
0.07
0.22
0.20
0.02
0.22
0.84
0.55
0.79
0.96
0.59
1.05
Sheet 84 of 95
Y MOMENT
(kN-m)
Z MOMENT
(kN-m)
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
Report no : SPEL/XX/YYY/XXX
APPENDIX - XX
DD MM YYYY
Sheet 85 of 95
79
67
ELASTIC MODULUS
tg
Bf/2t
d/Tw
PLASTIC MODULUS
ts
Conventional name
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
IPE80
80
46
3.8
5.2
59
3.69
23.22
5.82
0.028
13.74
117.9964095787
IPE100
100
55
4.1
5.7
74
5.79
39.41
9.15
0.028
15.31
351.3784056406
IPE120
120
64
4.4
6.3
93
8.65
60.73
13.58
0.028
17.42
889.590546432
IPE140
140
73
4.7
6.9
112
5.29
12.31
88.34
19.25
0.028
19.16
1981.3561184189
IPE160
160
82
7.4
127
5.541
25.4
16.66
123.86
26.10
0.028
19.99
3958.8687387013
IPE180
180
91
5.3
146
22.16
166.42
34.60
0.028
21.36
7431.2148213333
IPE200
200
100
5.6
8.5
12
159
28.47
220.64
44.61
0.028
21.45
12988.088541667
IPE220
220
110
5.9
9.2
12
177
5.978
37.25
285.41
58.11
0.028
22.44
22672.314338667
IPE240
240
120
6.2
9.8
15
190
47.27
366.65
73.92
0.028
22.29
37391.183424
10
IPE270
270
135
6.6
10.2
15
219
62.20
484.00
96.95
0.028
24.48
70577.867001375
11
IPE300
300
150
7.1
10.7
15
248
7.009
80.50
628.36
125.22
0.028
26.25
125934.05292188
12
IPE330
330
160
7.5
11.5
18
271
6.957 36.133
98.52
804.33
153.68
0.028
26.34
199097.32266667
13
IPE360
360
170
12.7
18
298
6.693
122.76
1019.15
191.10
0.028
26.89
313580.32796996
14
IPE400
400
180
8.6
13.5
21
331
1156.4
146.42
1307.15
229.00
0.028
27.55
490048.471125
15
IPE450
450
190
9.4
14.6
21
378
176.41
1701.80
276.38
0.028
29.38
791005.06853433
16
IPE500
500
200
10.2
16
21
426
6.25
214.17
2194.12
335.88
0.028
30.54
1249365.3333333
17
IPE550
550
210
11.1
17.2
24
467
254.06
2787.01
400.53
0.028
30.84
1884098.143872
18
IPE600
600
220
12
19
24
514
307.94
3512.40
485.64
0.028
31.31
2845526.7096667
19
I80
80
42
3.9
5.9
2.3
59
3.559 15.128
77.8
6.29
3.00
22.70
5.00
0.005
12.23
87500
20
I100
100
50
4.5
6.8
2.7
75
3.676 16.667
171
12.2
3.98825 1.0653
4.88
39.70
8.10
0.005
13.43
268000
21
I120
120
58
5.1
7.7
3.1
92
3.766 18.039
328
21.5
7.41
63.50
12.40
0.005
18.09
685000
22
I140
140
66
5.7
8.6
3.4
109
3.837 19.123
573
35.2
10.67
95.20
17.90
0.005
15.10
1540000
23
I160
160
74
6.3
9.5
3.8
125
3.895 19.841
935
54.7
14.78
136.00
24.90
0.005
15.68
3138000
24
I180
180
82
6.9
10.4
4.1
142
3.942
20.58
1450
81.3
19.83
187.00
33.20
0.005
16.17
5924000
25
I200
200
90
7.5
11.3
4.5
159
3.982
21.2
2140
117
7.95477 1.86
26.00
249.00
43.50
0.005
16.61
10520000
26
I220
220
98
8.1
12.2
4.9
176
4.016 21.728
3060
162
33.06
323.00
55.70
0.005
16.94
17760000
27
I240
240
106
8.7
13.1
5.2
192
4.046 22.069
4250
221
41.70
411.00
70.00
0.005
17.22
28730000
28
I260
260
113
9.4
14.1
5.6
208
4.007 22.128
5740
288
50.97
513.00
85.90
0.005
17.35
44070000
29
I280
280
119
10.1
15.2
6.1
225
3.914 22.277
7590
364
61.18
631.00
103.00
0.005
17.40
64580000
30
I300
300
125
10.8
16.2
6.5
241
3.858 22.315
9800
451
72.16
761.00
121.00
0.005
17.49
91850000
31
I320
320
131
11.5
17.3
6.9
258
3.786 22.435
12510
555
84.73
913.00
143.00
0.005
17.52
128800000
32
I340
340
137
12.2
18.3
7.3
274
3.743 22.459
15700
674
98.39
1078.00
166.00
0.005
17.61
176300000
33
I360
360
143
13
19.5
7.8
290
3.667 22.308
19610
818
114.41
1274.00
194.00
0.005
17.48
240100000
34
I380
380
149
13.7
20.5
8.2
306
3.634 22.336
24010
975
130.87
1480.00
221.00
0.005
17.50
318700000
35
I400
400
155
14.4
21.6
8.6
323
3.588 22.431
29210
149.68
1712.00
253.00
0.005
17.60
419600000
36
I450
450
170
16.2
24.3
9.7
363
3.498 22.407
45850
203.53
2394.00
345.00
0.005
17.65
791100000
37
I500
500
185
18
27
10.8
404
3.426 22.444
68740
268.11
3235.00
456.00
0.005
17.66
1403000000
38
I550
550
200
19
30
11.9
445
3.333 23.421
99180
349.00
4229.00
592.00
0.005
18.15
2389000000
39
HEA100
96
100
12
56
6.25
11.2
26.76
83.01
41.14
0.026
9.83
2581.3333333333
40
HEA120
114
120
12
74
7.5
14.8
38.48
119.49
58.85
0.026
12.09
6471.936
30
Iy
IZ
iy
iz
Wx
Wz
Wplx
Wplz
(cm4)
(cm4)
(cm)
(cm)
(cm3)
(cm3)
(cm3)
(cm3)
3069.5
34.2
214
Iw
(cm6)
ts
tg
Conventional name
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
41
HEA140
133
140
5.5
8.5
12
92
42
HEA160
152
160
15
43
HEA180
171
180
9.5
44
HEA200
190
200
6.5
45
HEA220
210
220
46
HEA240
230
47
HEA260
48
Bf/2t
Iy
IZ
iy
iz
Wx
Wz
Wplx
Wplz
(cm4)
(cm4)
(cm)
(cm)
(cm3)
(cm3)
(cm3)
(cm3)
55.62
173.50
84.85
0.026
13.58
15063.659625
104
76.95
245.15
117.63
0.027
14.12
31409.664
15
122
102.73
324.85
156.49
0.027
15.65
60210.874125
10
18
134
10
133.55
429.49
203.82
0.027
15.99
108000
11
18
152
10
177.69
568.46
270.59
0.027
16.60
193266.08033333
240
7.5
12
21
164
10
230.73
744.63
351.69
0.027
16.45
328485.888
250
260
7.5
12.5
24
177
10.4
23.6
282.12
919.77
430.16
0.027
16.97
516352.21354167
HEA280
270
280
13
24
196
10.77
24.5
340.19
1112.23
518.13
0.027
17.84
785366.64266667
49
HEA300
290
300
8.5
14
27
208
420.64
1383.28
641.16
0.027
17.59
1199772
50
HEA320
310
300
15.5
27
225
9.677
465.68
1628.09
709.73
0.027
17.57
1512358.734375
51
HEA340
330
300
9.5
16.5
27
243
495.73
1850.48
755.94
0.028
17.80
1824364.265625
52
HEA360
350
300
10
17.5
27
261
8.571
525.79
2088.48
802.27
0.028
18.10
2176576.171875
53
HEA400
390
300
11
19
27
298
570.92
2561.80
872.86
0.028
18.87
2942076.375
54
HEA450
440
300
11.5
21
27
344
631.02
3215.87
965.52
0.028
19.86
4146000
55
HEA500
490
300
12
23
27
390
6.522
32.5
86975
691.14
3948.86
1058.51
0.028
20.73
5643052.875
56
HEA550
540
300
12.5
24
27
438
6.25
35.04
111933
721.27
4621.82
1106.90
0.028
22.22
7188912
57
HEA600
590
300
13
25
27
486
37.385
141208
751.42
5350.39
1155.65
0.028
23.67
8978203.125
58
HEA650
640
300
13.5
26
27
534
5.769 39.556
175179
781.59
6136.30
1204.78
0.028
25.02
11027133
59
HEA700
690
300
14.5
27
27
582
5.556 40.138
215302
12179
811.92
7031.83
1256.73
0.028
26.22
13351908.375
60
HEA800
790
300
15
28
30
674
5.357 44.933
303443
842.58
8699.50
1312.25
0.028
29.27
18290286
61
HEA900
890
300
16
30
30
770
48.125
422076
903.16
10811.04
1414.47
0.028
31.49
24962000
62
HEA1000
990
300
16.5
31
30
868
4.839 52.606
553847
933.63
12824.38
1469.70
0.028
34.57
32073874.875
63
HEB100
100
100
10
12
56
33.45
104.21
51.42
0.027
8.38
3375
64
HEB120
120
120
6.5
11
12
74
52.92
165.21
80.97
0.027
9.48
9409.752
65
HEB140
140
140
12
12
92
78.52
245.43
119.78
0.027
10.40
22478.848
66
HEB160
160
160
13
15
104
6.154
111.15
353.97
169.96
0.027
10.74
47943.168
67
HEB180
180
180
8.5
14
15
122
151.43
481.45
231.01
0.027
11.46
93745.512
68
HEB200
200
200
15
18
134
200.34
642.55
305.81
0.027
11.78
171125
69
HEB220
220
220
9.5
16
18
152
6.875
16
258.48
827.05
393.88
0.027
12.35
295418.112
70
HEB240
240
240
10
17
21
164
7.059
16.4
326.89
1053.15
498.42
0.027
12.58
486946.368
71
HEB260
260
260
10
17.5
24
177
7.429
17.7
394.96
1282.92
602.24
0.027
13.18
753651.09895833
72
HEB280
280
280
10.5
18
24
196
471.04
1534.44
717.57
0.027
13.91
1130154.816
73
HEB300
300
300
11
19
27
208
570.86
1868.68
870.14
0.027
13.99
1687791.375
74
HEB320
320
300
11.5
20.5
27
225
615.92
2149.25
939.09
0.027
14.07
2068712.015625
75
HEB340
340
300
12
21.5
27
243
6.977
2156.3
646.00
2408.11
985.71
0.028
14.41
2454000
76
HEB360
360
300
12.5
22.5
27
261
6.667
676.08
2682.99
1032.48
0.028
14.73
2883251.953125
77
HEB400
400
300
13.5
24
27
298
6.25
721.27
3231.74
1104.03
0.028
15.56
3817152
78
HEB450
450
300
14
26
27
344
781.42
3982.38
1197.65
0.028
16.56
5258000
79
HEB500
500
300
14.5
28
27
390
5.357 26.897
107176
841.59
4814.57
1291.64
0.028
17.45
7017696
80
HEB550
550
300
15
29
27
438
5.172
29.2
136691
871.79
5590.61
1341.14
0.028
18.82
8855762.625
81
HEB600
600
300
15.5
30
27
486
31.355
171041
902.02
6425.14
1391.05
0.028
20.13
10965375
82
HEB650
650
300
16
31
27
534
4.839 33.375
210616
932.27
7319.89
1441.41
0.028
21.39
13362739.875
5
5
d/Tw
25
26.1
13
8091
Iw
(cm6)
ts
tg
Bf/2t
Iy
IZ
iy
iz
Wx
Wz
Wplx
Wplz
Conventional name
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(cm4)
(cm4)
(cm)
(cm)
(cm3)
(cm3)
(cm3)
(cm3)
83
HEB700
700
300
17
32
27
582
4.688 34.235
256889
962.72
8327.14
1495.04
0.028
22.52
16064064
84
HEB800
800
300
17.5
33
30
674
4.545 38.514
359084
993.58
10228.72
1553.13
0.028
25.31
21840229.125
85
HEB900
900
300
18.5
35
30
770
4.286 41.622
494065
1054.39
12584.11
1658.33
0.028
27.45
29461359.375
86
HEB1000
1000
300
19
36
30
868
4.167 45.684
644749
1085.05
14855.12
1716.26
0.028
30.20
37636488
87
HEM100
120
106
12
20
12
56
2.65
75.31
235.81
116.31
0.027
4.90
9925.1333333333
88
HEM120
140
126
12.5
21
12
74
111.55
350.61
171.63
0.027
5.62
24786.408969
89
HEM140
160
146
13
22
12
92
156.76
493.83
240.51
0.027
6.29
54328.558152
90
HEM160
180
166
14
23
15
104
211.90
674.57
325.46
0.027
6.74
108053.82951633
91
HEM180
200
186
14.5
24
15
122
277.43
883.45
425.19
0.027
7.29
199326.099456
92
HEM200
220
206
15
25
18
134
4.12
354.49
1135.15
543.21
0.027
7.70
346257.868125
93
HEM220
240
226
15.5
26
18
152
443.54
1419.45
678.55
0.027
8.18
572683.89543733
94
HEM240
270
248
18
32
21
164
657.47
2116.95
1005.93
0.027
7.45
1151987.30513067
95
HEM260
290
268
18
32.5
24
177
4.123 9.8333
779.74
2523.62
1192.46
0.027
7.90
1728347.11129167
96
HEM280
310
288
18.5
33
24
196
914.08
2965.64
1396.67
0.027
8.39
2520227.229696
97
HEM300
340
310
21
39
27
208
1251.81
4077.68
1913.17
0.027
7.76
4386028.385375
98
HEM305
320
305
16
29
27
208
5.259
900.74
2926.68
1374.40
0.027
9.91
2903168.5612969
99
HEM320
359
309
21
40
27
225
3.863 10.714
1275.68
4435.03
1950.72
0.027
8.06
5003864.651115
100
HEM340
377
309
21
40
27
243
4051.6
1275.77
4717.58
1952.70
0.028
8.57
5584496.069835
101
HEM360
395
308
21
40
27
261
3.85
1267.65
4989.32
1942.35
0.028
9.07
6137020.9413333
102
HEM400
432
307
21
40
27
298
3.838
14.19
104119
1259.64
5570.62
1934.13
0.028
10.09
7410303.7485867
103
HEM450
478
307
21
40
27
344
3.838 16.381
131485
1259.87
6331.02
1939.20
0.028
11.40
9251498.80482
104
HEM500
524
306
21
40
27
390
3.825 18.571
161929
1251.94
7094.28
1932.01
0.028
12.72
11186745.35616
105
HEM550
572
306
21
40
27
438
3.825 20.857
197984
1252.18
7932.69
1937.30
0.028
14.10
13515629.98464
106
HEM600
620
305
21
40
27
486
3.813 23.143
237448
1244.29
8772.09
1930.37
0.028
15.52
15907585.083333
107
HEM650
668
305
21
40
27
534
3.813 25.429
281668
1244.53
9656.97
1935.67
0.028
16.98
18649515.563333
108
HEM700
716
304
21
40
27
582
27.714
329278
1236.67
10538.99
1928.78
0.028
18.45
21397492.968107
109
HEM800
814
303
21
40
30
674
3.788 32.095
442599
1229.53
12487.71
1930.38
0.028
21.30
27775287.08442
110
HEM900
910
302
21
40
30
770
3.775 36.667
570435
1221.97
14441.77
1928.87
0.028
24.29
34746261.492
111
HEM1000
1008
302
21
40
30
868
3.775 41.333
722300
1222.47
16567.96
1939.67
0.028
27.43
43015036.237653
112
HD260X54.1
244
260
6.5
9.5
24
177
2788
214.47
714.46
327.73
0.027
19.67
382600
113
HD260X68.2
250
260
7.5
12.5
24
177
10.4
23.6
282.12
919.77
430.16
0.027
17.00
516400
114
HD260X93
260
260
10
17.5
24
177
7.429
17.7
394.96
1282.92
602.24
0.027
13.19
753700
115
HD260X114
268
262
12.5
21.5
24
177
6.093
492.81
1599.72
752.45
0.027
11.09
979000
116
HD260X142
278
265
15.5
26.5
24
177
621.56
2015.31
950.47
0.027
9.31
1300000
117
HD260X172
290
268
18
32.5
24
177
4.123 9.8333
31307
779.74
2523.62
1192.46
0.027
7.91
1728000
118
HD260X225
309
271
24
42
24
177
3.226
43752
1031.26
3395.72
1583.24
0.027
6.39
2483000
119
HD260X299
335
278
31
55
24
177
1422.51
4726.52
2189.68
0.027
5.18
3860000
120
HD320X74.2
301
300
11
27
225
330.61
1196.21
505.73
0.027
20.98
1041000
121
HD320X97.6
310
300
15.5
27
225
9.677
465.68
1628.09
709.73
0.027
17.57
1512000
122
HD320X127
320
300
11.5
20.5
27
225
615.92
2149.25
939.09
0.027
14.10
2069000
123
HD320X158
330
303
14.5
25.5
27
225
781.68
2718.42
1193.53
0.027
11.71
2741000
124
HD320X198
343
306
18
32
27
225
4.781
1000.70
3479.12
1530.17
0.027
9.68
3695000
3.8
d/Tw
13
7.375
25
12.5
31307
51895.9
Iw
(cm6)
ts
tg
Conventional name
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
125
HD320X245
359
309
21
40
27
225
126
HD320X300
375
313
27
48
27
127
HD320X368
395
319
33
58
128
HD360X134
356
369
11.2
129
HD360X147
360
370
130
HD360X162
364
131
HD360X179
132
Iy
IZ
iy
iz
Wx
Wz
Wplx
Wplz
(cm4)
(cm4)
(cm)
(cm)
(cm3)
(cm3)
(cm3)
(cm3)
3.863 10.714
68135
1275.68
4435.03
1950.72
0.027
8.09
5004000
225
3.26
8.3333
86905
1572.06
5521.80
2414.32
0.027
6.90
6558000
27
225
2.75
6.8182
113189
1974.71
6960.89
3041.12
0.027
5.92
8909000
18
15
290
817.26
2561.97
1237.21
0.027
18.89
4305000
12.3
19.8
15
290
903.91
2838.27
1369.26
0.027
17.33
4836000
371
13.3
21.8
15
290
1000.64
3139.27
1516.39
0.027
15.90
5432000
368
373
15
23.9
15
290
1109.01
3482.30
1682.70
0.027
14.57
6119000
HD360X196
372
374
16.4
26.2
15
290
1222.36
3837.43
1856.10
0.027
13.38
6829000
133
HD400X187
368
391
15
24
15
290
1223.63
3642.35
1854.67
0.026
14.48
7074000
134
HD400X216
375
394
17.3
27.7
15
290
1434.19
4262.35
2176.25
0.026
12.70
8515000
135
HD400X237
380
395
18.9
30.2
15
290
6.54
1571.73
4685.61
2386.99
0.026
11.74
9489000
136
HD400X262
387
398
21.1
33.3
15
290
1759.74
5259.53
2675.77
0.026
10.77
10940000
137
HD400X287
393
399
22.6
36.6
15
290
1944.01
5812.73
2957.04
0.026
9.91
12300000
138
HD400X314
399
401
24.9
39.6
15
290
5.063 11.647
110232
2124.87
6374.01
3236.48
0.026
9.23
13740000
139
HD400X347
407
404
27.2
43.7
15
290
4.622 10.662
124945
2380.45
7138.79
3628.66
0.026
8.48
15850000
140
HD400X382
416
406
29.8
48
15
290
4.229 9.7315
141317
2641.18
7964.72
4030.63
0.026
7.83
18130000
141
HD400X421
425
409
32.8
52.6
15
290
3.888 8.8415
159581
2937.97
8880.46
4489.32
0.026
7.24
20800000
142
HD400X463
435
412
35.8
57.4
15
290
3.589 8.1006
180162
3254.14
9877.69
4978.35
0.027
6.73
23850000
143
HD400X509
446
416
39.1
62.7
15
291
3.317 7.4425
204528
3625.04
11032.72
5552.26
0.027
6.26
27630000
144
HD400X551
455
418
42
67.6
15
290
3.092 6.9048
226110
3947.12
12050.78
6051.40
0.027
5.88
30870000
145
HD400X592
465
421
45
72.3
15
290
2.911 6.4444
250161
4283.69
13138.30
6574.46
0.027
5.58
34670000
146
HD400X634
474
424
47.6
77.1
15
290
2.75
274171
4634.48
14222.09
7116.76
0.027
5.30
38570000
147
HD400X677
483
428
51.2
81.5
15
290
2.626 5.6641
4993.99
15346.10
7680.05
0.027
5.06
42920000
148
HD400X744
498
432
55.6
88.9
15
290
2.43
5.2158
5552.40
17166.82
8548.92
0.027
4.74
49980000
149
HD400X818
514
437
60.5
97
15
290
2.253 4.7934
6202.70
19255.27
9561.31
0.027
4.44
58650000
150
HD400X900
531
442
65.9
106
15
289
2.085 4.3854
6938.44
21618.77
10707.64
0.027
4.14
68890000
151
HD400X990
550
448
71.9
115
15
290
1.948 4.0334
7739.24
24282.10
11961.64
0.027
3.91
81530000
152
HD400X1086
569
454
78
125
15
289
1.816 3.7051
20939
8645.27
27211.50
13375.63
0.027
3.68
96080000
153
Built-up Column
890
300.00
16
30
30
830
903.16
10811.04
1414.47
445.000
445.0
24996878.661535
1201.87
6402.00
1842.00
250.000
250.0
9522000
300.00
154
Built-up Key
500
Bf/2t
d/Tw
51.875
422076
30
300
20
Iw
(cm6)
13519
40
300
6.0924
2332
420
3.75
21
139628
40
153a
U80
80
45
47
5.63
7.8
106
19.4
3.09
1.32
26.5
6.4
29.60
12.0
0.029
7418.3
168
154
U100
100
50
8.5
4.5
64
5.88
10.7
206
29.3
3.90
1.47
41.2
8.5
45.20
16.1
0.029
9176.6
413
155
U120
120
55
4.5
82
6.11
11.7
364
43.2
4.61
1.59
60.667
11.1
66.30
21.2
0.028
10330.0
899
156
U140
140
60
10
97
6.00
13.9
605
62.7
5.43
1.75
86.429
14.8
93.90
28.2
0.028
11336.6
1800
157
U160
160
65
7.5
10.5
5.5
116
6.19
15.5
925
85.3
6.18
1.88
115.63
18.3
125.00
35.0
0.028
12472.5
3260
158
U180
180
70
11
5.5
133
6.36
16.6
1350
114.0
6.92
2.01
150
22.4
162.00
42.9
0.028
13459.9
5567
159
U200
200
75
8.5
11.5
151
6.52
17.8
1910
148.0
7.67
2.14
191
27.0
205.00
51.7
0.028
14389.7
9065
160
U220
220
80
12.5
6.5
166
6.40
18.4
2690
197.0
8.44
2.28
244.55
33.6
262.00
64.2
0.028
14726.6
14580
161
U240
240
85
9.5
13
6.5
185
6.54
19.5
3600
248.0
9.19
2.41
300
39.6
320.00
75.7
0.028
15509.9
22070
ts
tg
Bf/2t
Conventional name
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
162
U260
260
90
10
14
201
6.43
163
U280
280
95
10
15
7.5
216
164
U300
300
100
10
16
165
U320
320
100
14
17.5
166
U350
350
100
14
167
U380
380
102
168
U400
400
110
d/Tw
Iy
IZ
iy
iz
Wx
Wz
Wplx
Wplz
(cm4)
(cm4)
(cm)
(cm)
(cm3)
(cm3)
(cm3)
(cm3)
20.1
4820
317.0
9.96
2.55
370.77
47.7
396.00
91.6
0.028
15763.9
33260
6.33
21.6
6280
399.0
10.81
2.72
448.57
57.2
478.00
110.0
0.028
16167.1
48460
232
6.25
23.2
8030
495.0
11.66
2.89
535.33
67.8
571.00
130.0
0.028
16508.9
68970
8.75
247
5.71
17.6
10870
597.0
12.02
2.82
679.38
80.7
730.00
152.0
0.027
15018.9
95690
16
283
6.25
20.2
12840
570.0
12.93
2.72
733.71
75.0
781.00
142.0
0.027
17697.2
113200
13.5
16
313
6.38
23.2
15760
615.0
14.04
2.77
829.47
78.6
879.00
149.0
0.026
19804.1
145600
14
18
325
6.11
23.2
20350
846.0
14.96
3.05
1017.5
101.3
1081.00
192.0
0.027
19117.4
220300
(cm6)
fyb
fub
0.85*fyb 0.85*fub
4.6
240
400
204
340
M 12
84.3
4.8
320
400
272
340
(M 14)
115
5.6
300
500
255
425
M 16
157
5.8
400
500
340
425
(M 18)
192
6.8
480
600
408
510
245
8.8
640
800
544
680
10.9
900
1000
765
850
M 20
(M 22)
M 24
(M 27)
M 30
No of Edges Discontinous
(M 33)
694
0 Edge Discontinous
M 36
817
1 Edge Discontinous
(M 39)
976
2 Edges Discontinous
M 42
1120
3 Edges Discontinous
(M 45)
1300
4 Edges Discontinous
M 48
1470
(M 52)
1760
M 56
2030
(M 60)
2360
M 64
2680
(M 68)
3060
Iw
303
353
459
561
IT
cm
AX
Sw
cm
Kg/m
mm
Section class
K/Tf
(torsion const)
(cm3)
0.7
7.6434
6.0
51439.96
1.3462
1.21
10.323
8.1
101622.984
2.1228
1.74
13.21
10.4
183375.36
2.7619
2.45
16.426
12.9
305881.269
3.5507
3.62
20.091
15.8
474563.11
4.8919
4.8
23.947
18.8
712166
6.0000
7.02
28.484
22.4
1017343.75
8.2588
9.1
33.37
26.2
1466641
9.8913
12.9
39.116
30.7
2030364
13.1633
16
45.945
36.1
3018470.06
15.6863
20.2
53.812
42.2
4353060.94
18.8785
28.3
62.606
49.1
5860400
24.6087
37.5
72.729
57.1
7966844.94
29.5276
51.4
84.464
66.3
10565943.8
38.0741
67.1
98.821
77.6
14342620.3
45.9589
89.7
115.52
90.7
19360000
56.0625
124
134.42
105.5
25258716
72.0930
166
155.98
122.4
33392975
87.3684
0.869
7.6612
6.0
48200.1975
1.4729
1.6
10.751
8.4
99025
2.3529
1.71
14.349
11.3
181805.278
2.2208
4.32
18.451
14.5
307653.39
5.0233
6.57
23.067
18.1
489331.938
6.9158
9.58
28.185
22.1
741253.76
9.2115
13.5
33.819
26.5
1079481.94
11.9469
18.6
39.962
31.4
1521729.79
15.2459
25
46.605
36.6
2087360.88
19.0840
33.5
53.924
42.3
2767034.32
23.7589
44.2
61.705
48.4
3562341.16
29.0789
56.8
69.763
54.8
4489804.69
35.0617
72.5
78.556
61.7
5616698.77
41.9075
90.4
87.614
68.8
6905947.97
49.3989
115
98.022
76.9
8486015.48
58.9744
141
108.11
84.9
10225988.7
68.7805
170
118.97
93.4
12272931
78.7037
267
148.45
116.5
18684771.2
109.8765
402
181.18
142.2
27317967.2
148.8889
544
214.32
168.2
39000000
181.3333
5.26
21.236
16.7
440000
6.5750
6.02
25.336
19.9
763200
7.5250
IT
AX
Sw
cm4
cm2
Kg/m
mm4
Section class
K/Tf
(torsion const)
(cm3)
8.16
31.416
24.7
1296356.25
9.6000
12.3
38.771
30.4
2059200
13.6667
14.9
45.251
35.5
3106856.25
15.6842
21.1
53.831
42.3
4500000
21.1000
28.6
64.341
50.5
6621725
26.0000
41.7
76.836
60.3
9417600
34.7500
52.6
86.819
68.2
12542968.8
42.0800
62.4
97.264
76.4
16370900
48.0000
85.6
112.53
88.3
21735000
61.1429
108
124.37
97.6
25676718.8
69.6774
128
133.47
104.8
29096718.8
77.5758
149
142.76
112.1
32730468.8
85.1429
190
158.98
124.8
39650625
100.0000
245
178.03
139.8
49494375
116.6667
310
197.54
155.1
60418125
134.7826
353
211.76
166.2
69660000
147.0833
399
226.46
177.8
79453125
159.6000
450
241.64
189.7
89797500
173.0769
515
260.48
204.5
100693125
190.7407
599
285.83
224.4
120015000
213.9286
739
320.53
251.6
145125000
246.3333
825
346.85
272.3
167225625
266.1290
9.29
26.036
20.4
562500
9.2900
13.9
34.006
26.7
1079100
12.6364
20.1
42.956
33.7
1881600
16.7500
31.4
54.251
42.6
3057600
24.1538
42.3
65.251
51.2
4706100
30.2143
59.5
78.081
61.3
6937500
39.6667
76.8
91.041
71.5
9873600
48.0000
103
105.99
83.2
13647600
60.5882
124
118.44
93.0
17929843.8
70.8571
144
131.36
103.1
23108400
80.0000
186
149.08
117.0
30031875
97.8947
226
161.34
126.7
34536093.8
110.2439
258
170.9
134.2
38518593.8
120.0000
293
180.63
141.8
42714843.8
130.2222
357
197.78
155.3
50760000
148.7500
442
217.98
171.1
62010000
170.0000
540
238.64
187.3
74340000
192.8571
602
254.06
199.4
84988125
207.5862
669
269.96
211.9
96187500
223.0000
741
286.34
224.8
107938125
239.0323
IT
AX
Sw
cm4
cm2
Kg/m
mm4
Section class
K/Tf
(torsion const)
(cm3)
833
306.38
240.5
120240000
260.3125
949
334.18
262.3
142374375
287.5758
1140
371.28
291.5
170296875
325.7143
1260
400.05
314.0
195210000
350.0000
68.5
53.236
41.8
1404500
34.2500
92
66.406
52.1
2479632.75
43.8095
120
80.556
63.2
4044711
54.5455
163
97.051
76.2
6219044.75
70.8696
204
113.25
88.9
9133344
85.0000
260
131.28
103.1
12929718.8
104.0000
316
149.44
117.3
17761679
121.5385
630
199.59
156.7
29275904
196.8750
722
219.64
172.4
37567318.8
222.1538
810
240.16
188.5
47386944
245.4545
1410
303.08
237.9
70507368.8
361.5385
600
225.08
176.7
49064873.4
206.8966
1510
312.05
245.0
76146097.5
377.5000
1510
315.83
247.9
80442742.5
377.5000
1510
318.81
250.3
84191800
377.5000
1520
325.78
255.7
92364020
380.0000
1530
335.44
263.3
103202655
382.5000
1540
344.3
270.3
113299560
385.0000
1560
354.38
278.2
124535880
390.0000
1570
363.66
285.5
134886250
392.5000
1580
373.74
293.4
146049250
395.0000
1590
383.02
300.7
156183040
397.5000
1650
404.27
317.3
177650415
412.5000
1680
423.63
332.5
198368700
420.0000
1710
444.21
348.7
220713680
427.5000
30.31
68.969
54.1
9412243.75
31.9053
52.37
86.819
68.2
12542968.8
41.8960
123.8
118.44
93.0
17929843.8
70.7429
222.4
145.73
114.4
22737252.4
103.4419
406.8
180.27
141.5
29252004.3
153.5094
719
219.64
172.4
37567318.8
221.2308
1545
286.58
225.0
51472960.9
367.8571
3437
380.49
298.7
74385850
624.9091
55.87
94.578
74.2
17943750
50.7909
108
124.37
97.6
25676718.8
69.6774
225.1
161.34
126.7
34536093.8
109.8049
420.5
201.24
158.0
44554620.8
164.9020
805.3
252.32
198.1
58241592
251.6563
IT
AX
Sw
cm4
cm2
Kg/m
mm4
Section class
K/Tf
(torsion const)
(cm3)
1501
312.05
245.0
76146097.5
375.2500
2650
382.07
299.9
96107589
552.0833
4694
468.37
367.7
124313782
809.3103
168.8
170.61
133.9
51775220.3
93.7778
223.7
187.86
147.5
57634557.8
112.9798
295.5
206.3
161.9
64174772.1
135.5505
393.8
228.26
179.2
71512219
164.7699
517.1
250.32
196.5
79204435.3
197.3664
414.6
237.61
186.5
78886596
172.7500
637.3
275.5
216.3
93337682.5
230.0722
825.5
300.92
236.2
103015116
273.3444
1116
334.6
262.7
116607224
335.1351
1464
366.27
287.5
129791003
400.0000
1870
399.15
313.3
143034902
472.2222
2510
441.96
346.9
161953218
574.3707
3326
487.05
382.3
181978944
692.9167
4398
537.09
421.6
204796273
836.1217
5735
589.54
462.8
229942012
999.1289
7513
648.95
509.4
259939955
1198.2456
9410
701.38
550.6
285982128
1392.0118
11560
754.88
592.6
314516481
1598.8935
14020
807.96
634.3
343832724
1818.4176
16790
863.41
677.8
374637040
2060.1227
21840
948.06
744.2
424207899
2456.6929
28510
1043.3
819.0
482781568
2939.1753
37350
1149.2
902.1
550071763
3523.5849
48210
1262.4
991.0
627513600
4192.1739
62290
1385.8
1087.8
714964875
4983.2000
653.32
320.53
251.6
217.7742
1392.00
324
254.3
348.0000
2.24
11.1
8.7
1.45
10.500
2.8000
2.91
13.6
10.7
1.55
10.353
3.4235
4.28
17.1
13.4
1.60
7.667
4.7556
5.87
20.5
16.1
1.75
9.000
5.8700
7.62
24.2
19.0
1.84
7.679
7.2571
9.73
28.2
22.1
1.92
7.825
8.8455
12.3
32.4
25.5
2.01
8.112
10.6957
16.5
37.7
29.6
2.14
8.575
13.2000
20.2
42.6
33.4
2.23
8.877
15.5385
IT
AX
Sw
cm4
cm2
Kg/m
mm4
Section class
K/Tf
(torsion const)
(cm3)
26.3
48.6
38.2
2.36
9.348
18.7857
32
53.7
42.2
2.53
9.597
21.3333
38.7
59.1
46.4
2.70
9.846
24.1875
68.5
75.2
59.1
2.60
11.754
39.1429
62.4
76.8
60.3
2.40
10.971
39.0000
61.8
79.9
62.7
2.38
10.512
38.6250
BL
83
90.9
71.4
2.65
11.363
46.1111
(mm)