Professional Documents
Culture Documents
com
This workbook comes "as is" with no implied warranties or express guarantees.
The user assumes all responsiblity for the use of this workbook, modifications and output.
The User further agrees to verify the accuracy of all output and to satisfy themselves that
the results meet or exceed their expectation of accuracy and performance.
The user agrees to hold harmless all persons involved in the creation of the software.
THE DOWNLOAD AND/OR USE OF THE SOFTWARE IS AN IMPLIED ACCEPTANCE OF THESE TERMS AND CONDITIONS.
, P.E.
Date: 12/31/2016 Page : 1 of 4
Address: Street, # Project: 00-11-22-33-44-55
Contract : 2016-21
By: M.M. Checked: N.N.
Phone: +1 - 718 -
Fax: +1 - 718 - The base plate thickness for
E-mail: @gmail.com the HP-, M-, S-, W-shape column ( post ) is standing on
the concrete with axial compressive load by ASD 1) , 2) , 3)
( The US customary units )
The initial data for the calculation:
- the safety factor for the bending of steel: Wb = 1.67 See Subch. F1 1)
- the safety factor for the shear of steel: Wv = 1.67 See Subch. G1 1)
- the safety factor for the compression of concrete: Wc = 2.31 See Subch. J8 1)
- the compressive strength of concrete: f 'c = 4.00 ( ksi ) See Eq. J8-2 1)
- the material of base plate steel: ASTM A36 See Table 2-5 1)
- the minimum yield stress: Fy = 36.00 ( ksi )
- the minimum tensile stress: Fu = 58.00 ( ksi )
- the material of HP-, M-, S-, W-shape: ASTM A992 See Table 2-4 1)
- the minimum yield stress: Fy = 50.00 ( ksi )
- the minimum tensile stress: Fu = 65.00 ( ksi )
Notes:
1)
ANSI / AISC 360 - 10 Specification for Structural Steel Buildings, AISC 2010;
2)
AISC Steel Construction Manual, 14th Edition, AISC 2011;
3)
AISC Steel Design Guide 1, Base Plate and Anchor Rod Design, 2nd Edition, AISC 2006;
4)
Tolerances, variations and deviations shall be considered;
5)
Holes, welds and fasteners are not shown on the figure conditionally.
Version: 2016-2 bguzikov @ gmail.com
, P.E.
0 Date: 12/31/2016 Page : 2 of 4
Address: Street, # Project: 00-11-22-33-44-55
0 Contract : 2016-21
0 By: M.M. Checked: N.N.
Phone: +1 - 718 -
Fax: +1 - 718 - The base plate thickness for
E-mail: @gmail.com the HP-, M-, S-, W-shape column ( post ) is standing on
0 the concrete with axial compressive load by ASD 1) , 2) , 3)
( The US customary units )
The initial data for the calculation and
the calculation's results:
- the base plate's required area: A(req) = ( PaWc )/ ( 0.85f 'c( A2/ A1 )1/2 ) = 288.36 ( in2 )
- the nominal bearing strength of concrete: Pp = 0.85f 'cA1( A2/ A1 )1/2 = 1044.86 ( kips ) See Eq. J8-2 1)
- the allowable bearing strength of concrete: Pp/Wc = 452.32 ( kips ) See Chapter J8 1)
- the initial required base plate thickness: tp ( req ) = L( 2WbPa/ ( FyBN ) )1/2 = 1.7357 ( in ) See Eq. 14-7b 2)
Version: 2016-2 bguzikov @ gmail.com
, P.E.
0 Date: 12/31/2016 Page : 4 of 4
Address: Street, # Project: 00-11-22-33-44-55
0 Contract : 2016-21
0 By: M.M. Checked: N.N.
Phone: +1 - 718 -
Fax: +1 - 718 - The base plate thickness for
E-mail: @gmail.com the HP-, M-, S-, W-shape column ( post ) is standing on
0 the concrete with axial compressive load by ASD 1) , 2) , 3)
( The US customary units )
The calculation's results:
- the allowable flexural strength of base plate: Mp/Wb = FyZ1 / Wb = 21.56 ( in - kips ) See Subch. F2 1)
- the allowable shear strength of base plate: Vp/Wv = 0.60FyAw1Cv/ Wv = 25.87 ( kips ) See Subch. G2 1)
- the inequality for the design combined strength: 0.6425 < 1.0000 64.25%, OK See Eq. C-H3-6 1)