Professional Documents
Culture Documents
com
- the safety factor for the bending of steel: Wb = 1.6667 See Subch. F1 1)
- the safety factor for the shear of steel: Wv = 1.6667 See Subch. G1 1)
- the safety factor for the compression of concrete: Wc = 2.3077 See Subch. J8 1)
- the material of base plate steel: ASTM A36 ✓ See Table 2-5 1)
- the minimum yield stress: Fy = 36.00 ( ksi ) ✓
- the minimum tensile stress: Fu = 58.00 ( ksi ) ✓
- the material of HP-, M-, S-, W-shape: ASTM A992 ✓ See Table 2-4 1)
- the minimum yield stress: Fy = 50.00 ( ksi ) ✓
- the minimum tensile stress: Fu = 65.00 ( ksi ) ✓
Notes:
1)
ANSI / AISC 360 - 10 Specification for Structural Steel Buildings, AISC © 2010;
2)
AISC Steel Construction Manual, 14th Edition, AISC © 2011;
3)
AISC Steel Design Guide 1, Fisher J.M., Kloiber L. A. "Base Plate and Anchor Rod Design", 2nd Edition, AISC © 2006;
4)
Tolerances, variations and deviations shall be considered;
5)
Holes, welds and fasteners are not shown on the figure conditionally.
Spreadsheet V2016-3 bguzikov @ gmail.com
, P.E.
0 Date: 12/31/2016 Page №: 2 of 4
Address: Street, # Project: 00-11-22-33-44-55
0 Contract №: 2016-21
0 By: M.M. Checked: N.N.
Phone: +1 - 718 -
Fax: +1 - 718 - The thickness of base plate by the ASD.
E-mail: @gmail.com The I-section column (post) and the concrete foundation
0 at the axial compressive load. 1) , 2) , 3)
( The US customary units )
The initial data for the calculation and
the calculation's results:
- the base plate's required area: A(req) = ( Pa´Wc )/ ( 0.85´f 'c´( A2/ A1 )1/2 ) = 27.15 ( in2 )
- the nominal bearing strength of concrete: Pp = 0.85´f 'c´A1´( A2/ A1 )1/2 = 217.60 ( kips ) See Eq. J8-2 1)
- the allowable bearing strength of concrete: Pp/Wc = 94.29 ( kips ) See Chapter J8 1)
- the initial required base plate thickness: tp (req) = L´( 2´Wb´Pa/ ( Fy´B´N ) )1/2 = 0.3563 ( in ) See Eq. 14-7b 2)
Spreadsheet V2016-3 bguzikov @ gmail.com
, P.E.
0 Date: 12/31/2016 Page №: 4 of 4
Address: Street, # Project: 00-11-22-33-44-55
0 Contract №: 2016-21
0 By: M.M. Checked: N.N.
Phone: +1 - 718 -
Fax: +1 - 718 - The thickness of base plate by the ASD.
E-mail: @gmail.com The I-section column (post) and the concrete foundation
0 at the axial compressive load. 1) , 2) , 3)
( The US customary units )
The calculation's results of the base plate thickness
based on the conditionally isolated cantilevered strip
of unit width:
- the minimum shear stress of base plate material: Fs = 0.5774´Fy = 20.79 ( ksi )
- the inequality for the combined strength: 0.2800 < 1.0000 28%, OK