Professional Documents
Culture Documents
Tems Investigation 123
Tems Investigation 123
In general, Drive Test can be define as a methode that used to verify the actual condition
of RF signal certain operator at certain place.
Several functions of drive test :
1. Analyzing customer complaint of certain operator in their home or office area
2. Finding problem in BTS ( Timeslot Check, TRX Check, Swap Feeder)
3. Analyzing the result of optimization process (continuity and all of area)
There are softwares can be used for drivetest that installed on laptop. TEMS
Investigation (Ericsson), NEMO (Nokia).
Here the steps to start learning drivetest with TEMS Investigation :
5. Scanner for WCDMA (Ext Antenna GPS and RF, Data Cable)
Laptop Configuration
1. Power Management
Set Power Management Laptop always On :
Start -> Settings -> Control Panel -> Power Options -> Set All Power Scheme
never
2. Virtual Memory
Set Virtual Memory :
Start -> Settings -> Control Panel -> System
Advance -> Performance Settings
TEMS Investigation :
A. Workspace Configuration
After installition process, open Tems Investigation.
>> All Programs -> TEMS Investigation -> Data Collect
1.
2.
3.
4.
5.
B. Map Configurations
Create Geoset : Click Geoset Manager on Map window
1. On layer control
remove all layer except Pinpoint, Cell, Event, AMR, RF
Quality and Coverage layer
2. Add layer Route, Road, MCOM Site, and other *.tab
3. Save Geoset
4. Load Cell file : Configuration -> General -> Cellfile Load
5. Use Cell Definition File then choose cell file
4.
5.
6.
7.
Video Call CS
In general cs for video call is same as voice call, but in video call in dial
command we must add v.
i.e
Loop Start
Dial v081384760975
Wait 120
End Call
Wait 15
Loop End
C. DRIVE TEST
A. Configure Recording Properties : Menu Tab Logfile -> Recording
Properties
B. Select recording folder : Click Browse -> Select Directory
C. Select Quick logging and setup size of swap file after reaching message
I.
J. After all route complete, wait untill call end then stop command sequence
and stop recording.
F. POST PROCESSING:
o Report Generator
1. Open TEMS Data Collection : Start -> TEMS Products -> TEMS
Investigations6.1.4 Data Collection
2. Menu Tab Logfile -> Report Generator
3. Add logfile
6. Save *.mex
7. Choose Logfile : Click Browse file
8. If there are more than one logfile we can merge it by Merge Output
9. Choose Output directory : Click Browse dir
10. Give Prefix : Ded if Dedicated and Idle if Idle
14. Open the exported file into MapInfo : Menu Tab File -> Open
15. Create Thematic Map : Menu Tab Map -> Create Thematic Map
16. Choose Type -> Range
17. Template Name -> Region Ranges
18. Choose Table and Field (ie. Plotting RXQUAL_SUB from Dedicated
mode)
EVENTS on RXQUAL_SUB
21. Create Events on RXQUAL_SUB
22. Open again the exported file (Ded_orinaica)
23. Create Thematic Map : Menu Tab Map -> Create Thematic Map
24. Choose Type -> Individual
25. Template Name -> Region IndValue Default
26. Choose Table and Field
SPIDER GRAPH
29. Activate spider graph : Menu Tab Tools -> Tool Manager
30. Spider Graph Load and Autoload
31. See table structure of cell in MCOM Site : Menu Tab Table ->
Maintenance -> Table Structure -> View/Modify Table choose MCOM
Site
32. See table structure of CI in exported file : Manu Tab Table ->
Maintenance -> Table Structure -> View/Modify Table choose exported
file (ie. Ded_orinaica) -> Change type structure of CI
33. Click OK
34. Create Spider Graph : Tools -> Spider Graph -> Spider Graph
36. Save the Spider Graph table : Save Copy As -> (ie. orinaica)
37. From Spider Graph, We can analyze :
- Dominant Cells
- Overshoot Cells
- Swap Feeder
G. TROUBLESHOOTING :
o 2G Frequency Scanning
Purpose : to verify level signal each BCCH ARFCN plan
1. Setup frequency scan : Click Scan Properties
2. Select channels : Tab Scanned channels -> Manual selection -> Select
4. Decode BSIC
- TRX Check
Purpose : to verify damage TRX in each sector
Where is TRX ?