Professional Documents
Culture Documents
Heat and Mass Transfer: Fundamentals & Applications: Errata Sheet
Heat and Mass Transfer: Fundamentals & Applications: Errata Sheet
Errata Sheet
Last Update: December 13, 2011
Conversion Factors (Inside Front Cover)
Thermal resistance: Change 1 K/W = 0.52750 F/hBtu to 1 K/W = 0.52750 Fh/Btu
Chapter 1
p. 9, 6th line after the subtitle: Change denoted by W to denoted by W
p. 11, 4th line: Change qavg to qavg .
p. 13, the term
on the right of Eq. (1-17) should be even with the equal sign
Chapter 3
p. 161, 15th line below Eq. (3-50): change 0.05 W/m2K to 0.05 W/mK.
p. 168, line above Eq. (3-72), after corrected fin length, remove (
p. 171, Table 3-4, 1st line, last two columns: Change to in two places
1
m to L = 5/m
5
p. 197, Prob. 3-20, Answers: Change Answers to 154 W, 16.7C
p. 200, Prob. 3-37, 7th line: Change 28C to 24C. Do the same in the figure. [This is needed
to avoid negative value for the insulation thickness]
p. 208, Prob. 3-112: Delete Fig. P3-112
to this problem.
p. 211, Prob. 3-131: Place a computer-EES icon
p. 211, Prob. 3-135, Answer: Change 555 W to 492 W
p. 221, Prob. 3-216, Last line: Change (d) 3.4 cm to 3.3 cm
Chapter 4
p. 231, Example 4-2: Replace the calculations with the followings. Only change the changed
values
Lc
(D 2 / 4) L D 0.050 m
V
0.0125 m
4
4
DL
As
Bi
0.088 0.1
63.9 W/m K
k
hAs
h
450 W/m 2 K
0.01059 s -1
c pV c p Lc (7832 kg/m 3 )(434 J/kg K )(0.0125 m)
T (t ) T
e bt
Ti T
1 T (t ) T
1
95 40
ln
ln
254 s
b Ti T
0.01059 s -1 850 40
p.237, Table 4-1, last column for Plane wall: Change ln tan ln 5 Bi to n tan n = Bi
p. 239, Table 4-3, the last four Bessel function values in the last column should be positive, as
shown below:
2.6
2.8
3.0
3.2
0.0968
0.1850
0.2601
0.3202
0.4708
0.4097
0.3391
0.2613
transfer coefficient between the water and the container is 120 W/m2K, determine how long it
will take for the milk to warm up from 3C to 38C. Assume the entire surface area of the
cylindrical container (including the top and bottom) is in thermal contact with the hot water. Take
the properties of the milk to be the same as those of water. Can the milk in this case be treated
as a lumped system? Why? Answer: 4.50 min"
p. 279, Prob. 4-24, 1st line: Change is to in
p. 279, Prob. 4-26, last line: Change h. to h
p. 281, Prob. 4-47, Answers: Change 22,270 kJ/m to 22,270 kJ
Chapter 5
p. 309, Fig. 5-20 (lower part volume element of a general interior node of the fin): Change the
right hand side length from L (m )x to from L (m + )x
p. 353, Prob. 5-25: Change the problem statement to: 5-25
(or other) software.
p. 358, Prob. 5-55, last line: Change to Answers: (b) T1 = T4 = 93C, T2 = T3 = 86C
p. 359, Prob. 5-60: Change the problem statement to: 5-60
(or other) software.
p. 369, Prob. 5-136, 17th line: Change 28C to 20C. Do the same in the problem figure. Also,
3rd line from last: Change t=4s to t=5s.
p. 369, Prob. 5-137, 2nd line: Change 3 s to 5 s
Chapter 6
p. 385, Eq. 6-13: Change Viscous to Viscous forces
p. 409, Figure P6-10: Change bottom plate label from Ts,1 to Ts,2
p. 410, Prob. 6-28: 5th line: Change A and B to C1 and C2
p. 411, Figure P6-45: Change Air to Water
Chapter 7
p. 439, Figure 7-25: Change the figure caption to Flow patterns for in-line and staggered tube
banks
p. 461, Prob. 7-127, (c): Change 2.5 m to 2.9 m
Chapter 8
p. 467, Top right hand side of the page, below page number: Change Chapter 3 to Chapter 8.
p. 472, Eq. 8-14: Leave more space between the equation and the unit like that in Eq. 8-15.
pp. 501-506, The background color for Special Topic section disappears in these pages. Use a
consistent background color in the entire Special Topic section.
Chapter 11
p.654, 2nd equation below Eq. 11-33 for if Ch = Cmin: Change
Th , out Th , out
Th , in Tc , in
to
Th , in Th, out
Th , in Tc , in
drA
d
to A
dx
dx
to
p. 822, 7th line before Eq. 14-40: Change molecularmass to molecular mass
p. 822, 6th line before Eq. 14-40: Change themass to the mass
5
wA
y
C A
y
wA
y
wA
y