Professional Documents
Culture Documents
TB 1207C
Print Date: October 20, 1998
TECHNICAL DATA
FAX 8632324
Features
Highly resistant to heat, cold, weather, and has excellent electric insulation.
It is solvent-less so little shrinkage occurs.
Suitable for sealing comparatively large clearances.
Characteristics
Before cure
Units
Appearance
Specific Gravity
Sag
After cure
Appearance
Specific Gravity
Hardness
Pulling Strength
Elongation
Linear Shrinkage
Shear Strength
kg/cm
%
%
kg/cm
Result
Red
1.50
Non - sag
Red
40
0.3
1.50
170
20
60
Remarks
25C
25C
25C
JIS
Al plates used
Page 1 of 3
All recommendations and statements are based on our research and we believe them to be reliable. We cannot guarantee the results obtained through
the use of our products. All products are sold and samples are given without warranty, expressed or implied, of fitness for any particular purpose or
otherwise. The user shall make his own tests to determine the suitability of the product for his purpose. No agency or representative or employee of this
company is authorised to change this provision.
TB 1207C
Print Date: October 20, 1998
TECHNICAL DATA
FAX 8632324
100
100
100
100
- 0.4
- 0.8
- 0.3
+ 5.8
+ 5.0
Test Condition
Pressure media:
Turbine oil, 120C
The pressure was increased at the rate of 0.1 kg/cm per minute, until it reached one
kg/cm. Thereafter, the pressure speed was changed to 1 kg/cm at every 20 minutes.
Three Bond 1207C hardens when reacting with the moisture in the air. The curing cycle
naturally has a close relation with thickness of the layer formed, temperature and relative
humidity.
In 20 - 30 minutes after application at 25C and 50% RH, the surface becomes tack-free,
and turns into a rubber-like solid in 15 - 16 hours.
The maximum bond strength is obtained only after three days. Electric insulation
property is obtained in seven days after application.
Curing starts from the surface. Hence, when the layer is thick, the cure cycle becomes
longer accordingly.
Handling Precautions
1.
2.
3.
4.
5.
TB 1207C
Print Date: October 20, 1998
TECHNICAL DATA
FAX 8632324
8. Contains harmful ingredients. Do not use on tap water or hot water pipes.
9. Copper and copper alloy will corrode.
10. Depending on the surface, the surface may deteriorate. Before using, confirm
effect of the product.
11. Nonconductive. Do not use near electrical contact point.
12. After use, tightly close lid then store.
13. Avoid direct sunlight, store at low humidity area. (10 25 C)
14. For industrial use only.
Shelf Life
Packaging
Available in packing of 333ml, 150g and 20kg.
Disclaimer
For Industrial Use Only
(Do not use for household purposes)
The data contained in this report are obtained from experimental results, based on
out test method. We cannot assume absolute responsibility for accuracy and
safety. Before using this product, use your own judgment to determine whether or
not this product meets the requirements of the application and objectives. This
includes the burden of responsibility and hazardous danger. The extent of the
guarantee provides replacement for products, which are clearly unsatisfactory.
We assume responsibility for neither injury nor property damages resulting from
the misuse of this product.
We do not assume responsibility without written notice or contract.
Page 3 of 3
All recommendations and statements are based on our research and we believe them to be reliable. We cannot guarantee the results obtained through
the use of our products. All products are sold and samples are given without warranty, expressed or implied, of fitness for any particular purpose or
otherwise. The user shall make his own tests to determine the suitability of the product for his purpose. No agency or representative or employee of this
company is authorised to change this provision.