Professional Documents
Culture Documents
Pipe and Shell 2.1
Pipe and Shell 2.1
Terms
This software is the property of Pressure Vessel Engineering Ltd (www.pveng.com).
If you use this product you agree to the following terms and conditions:
1 This program is the property of www.pveng.com
2 This program is not available for sale under any circumstances.
The user uses this software at their own risk.
3 This notice must be included with all copies made.
4 This product is used "as is" without warrantees or liability. It is your responsibility
to know how to use this software. Any product designed with this software
is your responsibility. www.pveng.com does not guarantee the accuracy of this product.
All risk associated with this products use is assumed by the user.
5 www.pveng.com does not provide support for the use of this product
6 The codes and standards that this product is based on change periodically. It
is your responsibility to check that you are using an appropriate version.
7 This program is not a substitute for knowing the applicable codes and standards.
8 It is your job to ensure that you are using the most up-to-date version of this software
9 There is no guarantee that future versions of this program will be made available.
Locked Cells
This spreadsheet is locked for your convenience. You can move between input
cells using the Tab key. The password to unlock it is "100". If you make changes
to this spreadsheet you are required to remove the "www.pveng.com"
hyperlink. You are responsible for any and all changes that you make.
Comments
If you have comment, corrections or questions about this product send an email
to lb@pveng.com. I am sorry, but I do not answer all emails.
lb@pveng.com
Verification
This program was verified in one of the following ways
1 comparing it with an ASME code book examples - most examples are found in App. L
2 Hand calculations
3 Comparison with other commercial software
4 two or more of the above methods
Although every effort was made to make this software accurate and easy to understand, there
is no way to guarantee that it is accurate.
Registration
This program can not be registered. It remains the property of www.pveng.com
6 Dimensions:
7 4.500 <- Do - Outside Diameter
8 0.237 <- t - Nominal Wall Thickness t
9 3.937 <- Length
10 0.059 <- Corr, Corrosion Allowance
11
Long Seam
13
24 Variables:
25 UT = t*UTP+UTI = 0.237*0.125+0 undertollerance UT = 0.030
26 Ri = Do/2-t+corr = 4.5/2-0.237+0.059 inside radius Ri = 2.072
27 nt = t-Corr-UT = 0.237-0.059-0.03 nominal thick nt = 0.148
28 LDo = L/Do = 3.937/4.5 LDo = 0.875
29 DoT = Do/nt = 4.5/0.148 DoT = 30.340
30
57
Pipe - Inside Pressurized
Update Log
Date Change
16-May-99 Added Audit Sheet
Check Spelling
Checked Against Sample Calculation L-1.5.1
5-Oct-99 Added Maximum Pressure - changed from one page to two
Updated graphics to A99 Standard
Changed from UG-27 to App1-1 form of equation (either form is allowed)
Checked Against A99 Code Update
Locked Cells
8-Oct-99 Moved volume and weight calculations to separate sheet
Sample Values Entered
10-Oct-99 Added legal notice
Added print protection macro
17-Oct-99 Copied complete spreadsheet from Shell - Inside Pressurized
Added cells for pipe case
Removed UCS-79(d)
16-Jan-00 Copied complete sheet from B16.9 fittings - better format
Removed Stress Meter
Added Pipe Chart from B16.9
Combined Shell Spreadsheet
Updated Drawings
Protected Spreadsheet
20-Jan-00 Added Section IIA undertolerance Chart
29-Jan-00 Added Section IIB undertolerance Chart
Added E=1 shell thickness calculation
Set page maximum width for printouts
20-May-00 Reviewed Calculations for Audit - Pipe Sheet
Checked formulas against App1-1
Calculated formulas by hand
No changes made
31-May-00 Revised calculations to use UG-27 instead of App 1-1
(Allows calculation of circ joint stress)
New Hand Calculations Prepared
All calculations are now based on Ri instead of Ro
The E=1 thickness calculation has been removed
Pipe Sheet Verified Against Hand Calculations "Pipe and Shell" May 31/00
Shell sheet verified against hand calculations
Cells Locked
27-Sep-00 Separated Pipe and Shell Spreadsheets to individual workbooks
E=1 thickness calculations have been added
Checked for A2000 code changes - none
Moved Undertolerance and Pipe chart onto main sheet
Pased move and rename test
Cells Locked - Password = 100
31-Oct-00 Removed undertolerance from the inside diameter calculation
Undertolerance is still used
Inside radius varies slightly vs previous versions
19-Jun-01 Combined pipe and shell spreadsheets
Added exterior pressurization calculations and charts
Version number = 2.0
Verification Complete - Sample Calcs 1 - 4
Cells Locked - Password = 100
3-Jan-02 Updated to A2001 version
Added BM infor
checked for code calculation changes - none
Ran verification calculations
Added lookup chart for max elongation
Version = 2.1
Cells Locked - Password = 100