Professional Documents
Culture Documents
U. S. Patent 7,024,819 B1
INSTALLATION MANUAL
AND USER'S GUIDE
Revision 5.10
Autocbser is designed and manufactured by
, XCEllROINix
idt.>s .t-id ln.^^oltx,v ujMt
MEN'BER
Made in
the
U.S.A.
IDA
InkMnallunal fXmr AsM>ciutii)n
r.'.vr..'; 1.,^.:.. . I/..,'. >
NOTE: This equipmenthas been tested and foundto complywith the limitsfor a Class
B digitalde\'icc, pursuantto part 15of the FCC Rules. These limitsarc designedto pro
vide reasonable protectionagainst harmful interference in a residentbl installation. This
equipment generates, uses andcanradiate radio frequency energy and, if not installed
and used in accordancewdh the instructions, may cause harmfulinterference to radio
communications. However, there is no guaranteethat interference will not occur in a
partkubr installation. If thisequipment doescauseharmful interference to radio or tel
evision reception,which can be determinedby turning the equipmentofTandon, the
user is encouraged to try to correct the interference by one or moreof the following
measures:
An optional subsystem, the l-Opener system, allows the Autocloser to open and
dose a garage door from a remote, secure ternrsnalutilizing an electronic key. Each
electronic key has a unique code that is permanently stored in the key. Each key
provides one of 281,474,976,710,656 possible access combinations. Thafs 281
trillion possible numbers. If a thief wanted to circumvent the system by inputting
every possible number, it would take 8,925,513 years because the l-Opener system
reads only one key code per second. 1^e l-Opener system is highly secure, easy to
install and easy to operate.
TOOLS RECOMMENDED
Adjustable wrench
Phillips screwdnver
Standard screwdriver
Ladder Wire cutter/stripper
PARTS LIST
Item Description
1) 1 terminal wire 2fL
2) 1 Disable wire 25 ft
3) 1 Disable button
4) Velcrofasteners, 2 each-hook and loop strips
5) 1 Reflector assembly
6) 1 Nut
7) 1 Bolt
8) 1 Lock washer
9) 2 Disable button wood screws
10) 1 Power adaptor
11) 1 l-Opener terminal assembly (optional)
12) 2 l-Opener terminal plate wood screws (optional)
13) 1 l-Opener electronic key (optional)
14) 1 Autocloser control unit
15) Conspicuity tape
la. OPEN YOUR GARAGE DOOR AND UNPLUG THE GARAGE DOOR
OPENER BEFORE BEGINNING THIS STEP !!! BoH the reflector assembly. Item
(5), to the garage door opener Jbrace (Fig. 1-1).
Fig. 1-1
lb. Attach reflectiveconspicuity tape to reflector plate. Peel off adhesive backing from
the conspicuity tape and affix to side of reflector plate facingthe Autocloserunit. Topeshould
be aligned to cover most of the rectangular portionof reflectorplate (Fig. 1-3).
Reflector
Conspicuity Tape
Fig. 1-3
2. Connect power to the Autocloser. The Autocloser uses a 110 Volt AC ' DC power
adapter. The .\utoc)oser is shipped with the power adapter already connected to the
und (Fig. 2-1). No additional connections are required.
Fig 2-1
Bundle
wires with
Plug lllC twist tie.
Ault)Cl0SLT
ptnvcr adapter
into a 110 volt
AC outlet. Fig. 2-2
THE PO\)t^R ADAPTER MUST BE COMPLETELY PLUGGED IN TO INSURE
THAT IT STAYS IN THE OUTLET AND PROVIDES UNINTERRUPTED POWER
TO THE AUTOCLOSER.
Bundle excess wire in a roll and apply a twist tie. to prevent it from hanging down and be
coming an obstruction.
Infrared
Sensors
Fig. 3-1
The Autocioscr must be mounted in a position with the infrared sensors aimed straight
toward the reflector (Fig. 3-2). In order to accomplish this on all of the different
shaped garage door openers available, the Autocioscr box will8lwa}'s be mounted to the
power head assembly.
TIP: TheAulocloser will needlo bemounted at least2 inches le^ or rightof the center
thegarage door opener tofacilitate lining up tlte boxand reflector.
Fig. 3-2
The infrared
Position the Autocloser on
sensor should
the garage deer opener
motor housing with the label be in line with
side down the reflector
Switchthe .Autocloser to setup mode using the OWOFF/SETLIP switch on the back of the
Autocloser unk (Fig. 3-3).
Fig. 3-3
Determine yourmounting location by holding the Autocloser unitagainst thegarage door
opener power headassembly withthe infiared sensor&cing the reflector. While the Au
tocloser is insetupmode, it willemita continuous audible alarm whenthe infrared sensor
is whhmrangeand linedup withthe reflector. Adjust theunituntU it emitsthe continuous
audiblealarm.Markthe position of the unitby outlinmgit witha pencil(Fig. 3-4).
Fig. 3-4
NOTE: Read carefully and then rraiove the brightly colored warning label on
theside of the Autocloser unit. The'NO' terminals are under the warning label.
Fig. 5-2
6. Wire the disable button to the Autodoser. Locate the disable button next to the
garage door opener wall button. Attach one end of each wire. Item (2) to the disable
button terminals. Item (3). Attach the disable button to the wall using the provided
screws. Run the wire from the disable button to the Autodoser unit, attaching the
wire to the walland ceilingusing insulated stapbs (not included) (Fig. 6-1).
TIP: Route the wires through the notch in the disable button case so that it will
fit snugly against the wall.
Appro.ximate the length of the wire needed to connect to the Autodoser unit. Add one
foot to this approximation and cut the wire.Strip the wires on this end of Item (2) and
attach one ofthe wires to each ofthe screw terminals labeled *Disable */-' on the Au
todoser unit. (Either wirecan be connectedto either terminal) (Fig.6-2).
7. Test the Autocloser system. Plug in the garage door opener.
A. Switch the system to oa Close then reopen the garage door. As soon as the
door is open, the system will start a software timer. The de&ult door closer
deby time is 5 minutes. Whenthe timer completesthis Hve-minute count, the
system will begin to emit an audible beep. Thirty seconds after the beeping
b^ins, the door will partially close, then reopen. After a brief period oflime,
the door will close.
B. Reopen the door. Press the disable button and then release. The Autocloser
will beep twice to indicatethat the unit has been placed into temporary disa
ble'. The red dbable LED will begin to btinL The door will not automatically
close until the system is taken out of disable mode by closing the door.
The disable button is not a safety feature. The disable button will not re
verse a door that Is moving. If the door Is closing and needs to be
stopped, the garage door opener button should be pushedl The disable
button is intended to temporarily disable the system so that the garage
door can be left open. If the power goes out while the unit is in disable
mode, the unit will restart in disable mode once the power is restored.
To permanently disable the system, turn off the Autocloser using the orV
off switch.
TIP- The disable button can be pressed during the audible alarm to reset
the timer in order to give additional time before the unit auto closes the
garage door. Toput the unit in disable mode, press the disable button
again.
C. Prcis the disable button again. The Autocloser will beep twice while the but
ton is in and six times when it b released in order to indicate that the unit has
already been placed in temporarydbable. The unit can only be re-enabled by
closing the garage door. Press the garage door opener wall button. The Aulo-
cbser will beep twice once the door begins to close and the dbable light will
stop blinking. Thb indicates that the Autocloser b no longer in 'temporary
dbable'. Once the door b closed, press the dbable button again. The unit will
beep twice while the button b in and six times when it b releasedto indicate
that the door b closed and cannot be placed in 'temporary dbable' mode.
D. Open the door. Simulate an obstruction in the doorway by pbcing a 2X4
across the middle ofthe door threshold.
STAY AWAY FROM THE DOOR WHILE IT IS CLOSING - THE GAR
AGE DOOR CAN CAUSE SEVERE INJURYIM
the timer finishes it's counL the system will perform the door closing
procedure. When the door hits the obstruction, it should return to the open
position. The .Autocloscr will attempt to closethe door twice. \Mienthe Auto-
closer has finished its closing cycle, it will sense that the door has not closed
and transition to 'malfunction disable' mode. Note: the red disable LED will
begin to blinkand the unit willbeeponceevery20 seconds. Pressthe disable
button to exit maliunction disable. The Autocloser will beep three times to
indicate that it is leaving the malfunction disable mode and returning to nor
mal operational mode.
TIP: To minimize the time required to test, set theAutocloser delay time to
two minutes, (see Operation and Programming Item (4).)
When the timer finishes its counL the system will perform the door closing
procedure. The photo eyesystem should allow the doorto move onlyslightly.
When the Autocloser has fmished it's closing cycle, it will sense that the door
has not closed and transition to malfunction disable mode. Note: the red disa
ble LED will begin to blink and the unit will be^ once e\'ery 20 seconds. Re
move the tape &om the photo eye.Press the disablebutton to exit malfunction
disable mode. The Autocloser will beep three times to mdicate that it is leav
ingthe malfunction disable mode and returningto normaloperationalmode
F. Test for false reflections. Shut the garage door and switch the unit to 'Set Up'
mode. Verify that the beeper does not make any noise. If the beeper is
sounding, make sure there is nothing in front of the Autocloser unit causing
fabe reflections.
OPEN YOUR GARAGE DOOR AND UNPLUG THE GARAGE DOOR OPENER BEFORE BEGIN-
NINGTHIS tNSTALLATtON Hi
Drill holes for the I-Opener wire harness. Visually inspect the opposite side
of the doorframe for wires and other objects that may be damaged by the drill
Estimate the center of the sketch. Using a 7/16-inch drill, make a 7/16-inch
hole through the center of the sketch. Feed all of the I-Opener terminal wire
through the hole (Rg. 9).
Fig. 9
10. Drill holes Torthe I-Opener terminal plate Position the back of the termi
nal in the hole. Mark the terminalplate holes with a pencil Remove the termi
nal plate and drill the pbte holes with a 1/8-inchdrill
II. Fasten the terminal plate to the doorframe Reposition the terminal plate
with termmal in the hole. Use 1 inch ttS wood screws. Item (12), to &stcn the
pbte to the doorframe(Fig. 11).
Fig. 11
12. Wire the I-Opener terminal to the Autocloser. Run the wire fiom the I-Opener
terminal to the Autocloser unit attaching the wire to the wall and ceiling using
insulated staples (not included)(Fig. 12-1).
Fig. 12-1
^proximate the length of the wire needed to connect to the Autocloser. Add one
foot to this approximation and cut the wire. Strip the wires on this end of Item (11).
Attach the colored or str^ed wire to the screw terminal labeled GA + on the Auto-
cbser box. Attach the white wire to the screw terminal labeled GA - on the Autoclos
er unit. (Fig. 12-2).
Attach whit wire
to GA- and colored
or striped wire
toGA+
13. Insure (hat nobody is standing under the garage door. Plug the garage door
opener back into its 110 Volt household receptacle.
14.Program your I-Opener electronic key. Your I-Opener system willremember
up to nine electronickey codes at a giventime. Have all of the keys present when
programming the system. Switch the Autocbscr to setup mode. Press each key
into the I-Openerterminal for 2 seconds.The .Autocloser will beep 3 times after
eachkey is read. When all of the keys have been read,switchthe Autocloscr to
on mode. Test each key by pressing it into the I-Opener terminal. (Remember:
Whenever one key is programmed,all keys miut be reprogrammed.) To erase all
key codes from the .Autocloser, press the disable button while the unit is in setup
mode.
OPERATION AND PROGRAMMING
The Autocloser s^'stcm is ready to operate straight out of the box. Once installed, the unit
will aulotnaticallyclose your garage door aHer the preset software timer has finished it's
count. The system features are enumerated below.
TIP-Ifthegarage door ispartially closed, theAutocloser wilt think the door isfully
closed and will never perform the auio closing function. Because the unit thinks the
door is closed, it cannot beput into 'temporarydisable
2) Malfunction Dbable - Thb dbable occurs automatically whenthe garage door fails
to close after two Autocloser attempts. When the unit b in 'mal^nction dbable'
mode, the red dbable light will blink and the unit will beep once every 20 seconds.
Determine if something b blocking your garage door then re-enable the unit by
pressing the dbable button. The unit will beep 3 times.
3) Auto close Cancel - The current auto closing operation can be cancelled when the
unit b sounding the audible closing alarm (auto close state). The operation can be
cancelled by pressing the dbable button which will reset the software timer. The unit
will immedblely begin the software timer counting again.
The auto closecancel feature WILL NOT reverse a door that is already moving.
Thb feature simply cancels further Autodoser operation. If the door is already
closing and it needs to be stopped, the garage door opener button should be
pushed!
TIP- The auto close cancelfeature can be used wheneverthe Autocloser begins its
continuous warning beq/s.
4) Set the auto close delay time - The deby time can be set to 2, S. 10, IS and 20
minutes. To set the deby time press and hold the disablebutton while the unit is in
run mode. The unit will initiallybeep Uvice. The unit will sound a series of beeps
everyS seconds to signify the deby timethatwould be set if the disable button were
released immedbtel}'.
Afterreaching S beeps,if you have missed the setting youdesired, you mayrelease
the button and press it again to restart the sequence.
*NOTE: It is recommended that you set your dday time for as short a deby as pos
sible, to mmimizethe amountoftime your garage is vulnerableto mtruders.
6) Erase aD I-buttons- If you bse one or more of your I-buttons, you shoulderase the
key codes while waiting for repbcemenb. Switch the unit to setup mode. Press the
disablebutton. The system will beep 3 timesto indicate that the I-buttonkey codes
have been erased. Switch the unit to 'ON' mode.
22
TROUBLE SHOOTING GUIDE
Please readthissection carefully if yourAutocloser doesnotfunction correctly.
STEP 2
Does the electrical outlet work?
Yes- Rease contact Xcel-
tronix, Inc. for possible war
ranty service.
No- Fix Electrical outlet.
After the door has been open for the set STEPS
delay time, the unit does not beep. Is the garage door fullyopen?
No- Open garage deer and
recheck.
Yes- Go to Step 4.
23
STEP 4
Press and release the Disable button
while the unit is on. Does the unit
beep twice?
No- Go to Step 1 and re
align the reflector.
Yes- Go to Step 5
STEPS
1) Are you sure you are waiting the
full delay tinm?
No- Press and hold the
Disable button. The unit will
beep twice Initially, then
after 5 seconds It will beep
once. Release the disable
button. This sets the delay
time to 2 minutes.
Yes- Go to Step 6
STEPS
1) Disconnect unit from the garage
door opener.
2) Plug it in to any wall outlet.
3) Hold the unit about a foot away
from the wall and switch it to
'setup*. It should continually beep.
4) Switch it to 'on'.
5) Hold the unit about a foot away
from the wall.
6) Wait for the delay timer to com
plete ifs count (Remember to
keep holding the unit facing the
wall. If the unit doesn't think the
reflector Is in the open position, it
will not go into closer mode.) The
unit should begin beeping after
the delay timer finishes it's count.
7) Unit begins to beep?
Yes- Unit is working. Fol
low ail Installation steps.
No- please contact Xcel-
tronix. Inc. for possible
warranty service.
STEP 8
1) While in setup mode. Press an I-
Opener l-button into the I-
Opener terrrdnal. Unit should
t)eep three times.
25
2) Unit beeps three times?
Yes- Unit has been pro
grammed with this {-button Irey
code. Go to Step 9
No-Go to Step 10
STEP 9
1) Switch unit into on mode.
2) FYess an l-Opener l-button into
the l-Opener terminal. Unit should
operate garage door.
3} Unit operates door?
Yes- Unit is working
No- Please contact Xceitronix,
Inc. for possible warranty service.
STEP 10
1) Check l-Opener ternnnal connec
tion at the Autodoser. The colored or
striped wire should be connected to
the GA+ and the white wire should
be connected to the GA-
2) Is this the first time you have gone
through these tests?
Yes- Go to Step 7
No- Please contact Xceitronix,
Inc. for possible warranty service.
26
LIMITED LIFETIME WARRANTY
What does the warrant}- cover? Any defect in parts and product workman
ship that arises from normal household use in accordance with the Installation
Mimual and User's Guide.
How long does the warranty last? Parts are warranted for life* and labor is
warranted for 90 days from the date ofpurchase.
'Lifetime warranty only applies to the original owner. The product must be regis
tered using the form at the end of this manual or the original proof of purchase
must be shown to receive warranty service.
Who gets the warranty? Thb warranty is limited to the consumer who origi
nally purchased the product
How does the warranty service work? If the Autocloser is defective, we will
rqrair or, at our option,replace it. If we repair your product, we may use new or
reconditioned replacement parts. If we choose to replaceyour Autocloser, we may
replace it with a new or reconditioned unit of the sanwor similardcsiga During
the first 90 days from the date of purchase, all parts and labor are free of charge.
After the fiist 90 days from the date of purchase, all parts are free and a nominal
diagnosischarge will be collected for bbor.
How is warranty service obtained? We suggest that you retain your original
packing materiabin theeventyouneedto shipyourAutocloser. Shipthe unitto:
Xceltronix, Inc
Attn: Warranty Service Dept.
1226 Exchange Drive
Richardson, TX 75081
Include your name, address, telephone number, proof of date and place of pur
chase, and a description of the problem. If you contact Xceltronix, Ina or mail the
unit after the first 90 days from the date of purchase, you will be chargeda bench
fee of S2S.00to repair or, at our option, replace the unit
What does the warranty not cover? This warranty does not cover installation,
defectsresultmg fromaccidents, misuse or abuse, unauthorized rqpairor modifica-
tbn, fire, flood, other natural disasters or acts ofwar.
27
FAQ
28
6. Do I have to install the disable button? Yes, while the unit will work without
the disable button installed, it is needed to re^nable the system after a mal
function. The disable is abo a convenient way to temporarily dbable the unit
without turning it off.
7. I returnedhometo find mygaragedoor open. Whydid my Autocbser fail to
close my garagedooi? If you heara beep onceevery20 seconds and find the
dbable LED blinking,the unit did attemptto cbse Ae door. The Autocbser
willattemptto cbse yourgaragedoor 2 times.Reasonswhythe door might
re-openinclude bindmgdoor wheeb or an obstruction in the path of the door.
The Autocbser may haveattempted to cbse the doorbut failed due to the
prevbus reasons. Tie Autocbser does not interfere with the mandatoiysafi^
ty features included on modemgaragedoor openers. Re-enable the Autocbs
er by pressing the dbable button.
8. I bst oneof my I-Openerelectronic keys.Howdo I erasethe lost key's seri
al number? Switch the Autocbso' to setup mode and press the dbable button.
All key codes are now erased. Reprogramyour remainingkeys by folbwing
step S in the Operatbn and Programming sectbn ofthb manual.
9. Can a burglaropen my garage by shorting out the I-Opener terminal?No, the
Autocbser reads the uniqueelectronb key code and comparesit to the pre
programmed keycodes before it opens thedoor. It would be virtually impos
sible to simubte the electronb key's code.
10. Can I order additbnal keys? Yes, pbase bg on to http://www.autocloser.com
for ordering informatbn.
11. Does my unit comewith a warranty? Yes,we are pleasedto offeryou a lim
ited lifetimewarranty. Read the warranty section of this manual for full de-
taib. In order to obtain warrantyservice you must provide proof ofthe date
and pbce of purchaseofthe product To insurethb, fill in the enclosedwar
ranty card and mail to: Xceltronix, Inc., 1226ExchangeDrive,Rbhardson,
TX 7S081. Incbde a copy of your sales receipt with the date of purchase.
REPLACEMENT PARTS
Or contact us:
^ XCEllRGINiX
Xceltronix, Inc.
1226 Exchange Drive
Richardson, TX 75081
972-437-9393
30
Autocloser Warranty
First Name Last Name
Address
Phone#
32