Professional Documents
Culture Documents
The Lumentum tunable SFP+ optical transceiver is a full duplex, integrated fiber optic
transceiver that provides a high-speed serial link at 9.95 to 11.3 Gbps signaling rates. The
transceiver supports the enhanced small form factor pluggable module (SFP+) specification
SFF-8431 Rev. 4.1 for the electrical interface, SFF-8432 Rev. 5.0 for the mechanical interface,
SFF-8690 Rev. 1.4 for the tunability interface, and SFF-8472 Rev. 11.3 for the management
interface.
The transceiver complies with IEEE 802.3-2012 clause 52 and it Key Features
supports 10GBase-ZR/ZW (Ethernet), 10 G Fibre Channel (FC), SFF-8431 MSA Revision 4.1 compliant
and corresponding forward error correction (FEC) rates. It SFF-8690 MSA Revision 1.4 compliant
supports Telcordia GR-253-CORE OC-192 LR-2 and ITU-T G.959.1
Full C-band tunable laser source
P1L1-2D2 data rates.
50 GHz ITU channel spacing
It integrates the receive and transmit path on one module. On the 80 km reach
transmit side, the serial data stream is passed from the electrical Operating temperature range of 5 to 70C
connector to a modulator driver. The modulator driver biases and
Maximum power dissipation of 1.5 W
modulates a C-band cooled tunable transmitter, enabling data
transmission over up to 80 km of single-mode fiber through an RoHS 6/6 compliant
industry-standard LC connector. On the receive side, the 10 G Limiting SFI AC-coupled electrical output interface
optical data stream is recovered from an avalanche Supports digital diagnostic monitoring
photodetector (APD) through a transimpedance amplifier to the
electrical connector. This module features a hot-pluggable Applications
SFI-compliant electrical interface. Wide area networks (WAN)
Local area networks (LAN)
Storage area networks (SAN)
Ethernet switches and applications
FC switches and applications
Compliance
IEEE 802.3-2012 clause 52 standard
10 G FC standard
SFF-8431 Rev 4.1
SFF-8432 Rev 5.0
SFF-8472 Rev 11.3
SFF-8690 Rev 1.4
Class 1 laser safety
Tested in accordance with Telcordia GR-468
ROHS 6/6
www.lumentum.com 2
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
RS1 MOD_ABS
Low-Speed Interface
Connections Definition
Figure 1. Lumentum tunable SFP+ optical transceiver functional
block diagram SCL/SDA 2-wire serial interface clock and data line.
Tx_Fault Output pin. When asserted high, indicates that the
module has detected a transmitter fault condition
The transceiver has several low-speed interface connections. related to laser operation or safety.
These connections include: transmitter fault (Tx_Fault), Tx_Disable Input pin. When asserted high or left open, the
transmitter disable (Tx_Disable), module absent (Mod_ABS), transmitter output is turned off. When Tx_Disable
receive loss of signal (Rx_LOS), and a 2-wire serial interface clock is asserted low or grounded, the module
transmitter is operating normally.
(SCL) and data (SDA). Rate select (RS0 and RS1) is not used in this
product. RS0 and RS1 Input pins. These pins are not used in this product.
Mod_ABS Output pin. Asserted high when the SFP+ module
The transceiver supports the SFI electrical interface. The is absent and is pulled low when the SFP+ module
electrical interface is based on a high-speed, low-voltage logic is inserted.
AC-coupled linear interface with a 100 nominal differential Rx_LOS Output pin. Asserted high when insufficient
impedance. optical power for reliable signal reception is
received.
www.lumentum.com 3
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
Tunable SFP+ modules are hot pluggable and active connections are powered by individual power connections for the transmitter (VCCT)
and the receiver (VCCR). Multiple modules can share a single 3.3 V power supply with individual filtering for each VCCT and VCCR. The host
shall generate an effective weighted integrated spectrum RMS noise of less than 25 mV in the 10 Hz to 10 MHz frequency range. Detailed
power supply specifications are given in SFF-8431 Rev. 4.1 Section 2.8. Figure 2 shows a typical application schematic.
www.lumentum.com 4
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
Section 3.10 Tunable SFP+ Channel Number and Wavelength 4 LVTTL-I/O SDA 2 2-wire interface data line
2
Section 3.11 SFP+ 2-Wire Interface Protocol and Management 5 LVTTL-I SCL 2-wire interface clock
Interface 6 Mod_ABS2 Indicates module is not present.
Section 3.12 Digital Diagnostic Monitoring Accuracy Grounded to VEET or VEER in the module.
Section 3.13 Timing Requirement of Control and Status I/O Asserted high when SFP+ module is
absent and pulled low when the SFP+
Section 3.14 Timing Diagram for Power-On/Hot-Plug and
module is inserted
Tx_Disable Event
7 LVTTL-I RS03 Rate select 0 (not used)
Section 3.15 Regulatory Compliance
8 LVTTL-O Rx_LOS2 Receiver loss of signal indicator.
Section 3.16 T-SFP+ Transceiver Mechanical Diagram
Asserted high when receiving
insufficient optical power for reliable
3.1 Pin Function Definitions signal reception.
9 LVTTL-I RS13 Rate select 1 (not used)
VEER 10 10 VEER1 Module receiver ground
11 VEER
RS1 9 1
12 RD1 11 VEER Module receiver ground
Rx_LOS 8
13 RD+ 12 CML-O RD Receiver inverted data output
Toward Bezel
RS0 7
Toward ASIC
Mod_ABS
GND VEER
GND VEET
SCL/SDA
Tx_Fault
Rx_LOS
2
RS0
RS1
2
TD +/
SFP+ Module
2
RD +/
www.lumentum.com 5
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
D C' C
Rx
Connector
ASIC/
SFP+ Module
SERDES
Tx
A B' B
www.lumentum.com 6
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
www.lumentum.com 7
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
3.9 OSNR Characteristics with External CDR Implemented on the Host Board5,6
Rx Power Range (dBm)
Data Rate (Gbps) BER Dispersion (ps/nm) Min Max OSNR (dB)
10.709 1x10 4 0 18 7 16
10.709 1x10 4 400 to +1450 18 7 19
11.1 1x10 4 0 18 7 17
11.1 1x10 4 400 to +1450 18 7 20
www.lumentum.com 8
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
www.lumentum.com 9
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
3.14 Timing Diagram for Power-On/Hot-Plug and Tx Disable Event (Not to Scale)
www.lumentum.com 10
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
www.lumentum.com 11
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
Recommended Cleaning and Degreasing Chemicals The transceiver complies with 21 CFR 1040.10 except for
Lumentum recommends the use of methyl, isopropyl, and deviations pursuant to Laser Notice No. 50 dated June 24, 2007.
isobutyl alcohols for cleaning.
Housing
The transceiver housing is made from zinc. Caution
Operating this product in a manner inconsistent with intended
4.2 Electrostatic Discharge usage and specifications may result in hazardous radiation
Handling exposure.
Normal electrostatic discharge (ESD) precautions are required
during the handling of this module. This transceiver is shipped in Use of controls or adjustments or performance of procedures
ESD protective packaging. It should be removed from the other than these specified in this product data sheet may result
packaging and otherwise handled in an ESD protected in hazardous radiation exposure.
environment utilizing standard grounded benches, floor mats,
and wrist straps. Tampering with this laser product or operating this product
outside the limits of this specification may be considered an
act of manufacturing and may require recertification of the
modified product.
www.lumentum.com 12
Tunable SFP+ Optical Transceiver with Limiting Electrical Interface JST Series
European Union
This product complies with the European Unions Low Voltage
Directive 2006/95/EC and EMC Directive 2004/108/EC and is
properly CE marked. This declaration is made by Lumentum
United States Operations LLC who is solely responsible for the declared
This device complies with Part 15 of the FCC Rules. Operation is compliance.
subject to the following two conditions:
Japan
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and complies with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
Translation: This is a Class B product based on the standard of the
generates, uses, and can radiate radio frequency energy and, if
Voluntary Control Council for Interference from Information
not installed and used in accordance with the instructions, may
Technology Equipment (VCCI). If this is used near a radio or
cause harmful interference to radio communications. However,
television receiver in a domestic environment, it may cause radio
we cannot guarantee that interference will not occur in a
interference. Install and use the equipment according to the
particular installation. If this equipment causes harmful
instruction manual.
interference to radio or television reception, which can be
determined by turning the equipment off and on, users are
encouraged to try to correct the interference by one or more
of these measures:
www.lumentum.com 13
Ordering Information
For more information on this or other products and their availability, please contact your local Lumentum account manager or
Lumentum directly at customer.service@lumentum.com.
North America
Toll Free: 844 810 LITE (5483)
China
Toll Free: 400 120 LITE (5483)