Professional Documents
Culture Documents
BFC 43103 PDF
BFC 43103 PDF
rr
$T 4?
s
Y 9.',
o o
-l
o-
s
?orr$"tr
UNIVERSITI TUN HUSSEIN ONN MALAYSIA
FINAL EXAMINATION
SEMESTERI
SESSTON 2012t2013
PROGRAMME 4 BFF
CONFIDENTIAL
BFC 4043/BFC 43103
SBCTION A
Ql (a) Briefly, discuss ONE (1) mechanical modification and ONE (1) hydraulic
modification technique for ground improvement.
(6 marks)
(b) The in situ void ratio, e of a borrow pit is 0.72. The borrow pit soil is to be
excavated and transported to filI a construction site where it will be compacted
to a void ratio of 0.42. The construction project requires 10,000 m' of
compacted soil fill.
Determine the volume of soil that must be excavated from the borrow pit to
provide the required volume of fill.
(5 marks)
(c) Refer to Figure Ql (c). For a large filI operation, the average permanent load
[Ao'rpl] on the clay layer will increase by about 57.5 kNim2. The average
effective overburden pressure on the clay before the fill operation is 71.88
kN/m2. For the clay layer, which is normally consolidated and drained from
:
top and bottom, it is also given that H, : 4.57 ID, C. : 0.30, eo : 1.0, cn 9.68
x l0-' cm'lmin. Determine the following:
(i) The primary consolidation settlement of the clay layer caused by the
addition of the pennanent load, Ao'(p).
(2 marks)
(iii) The temporary surcharge, Ao'1g, that will be required to eliminate the
entire primary consolidation settlement in 12 months by the
precompression technique.
(7 marks)
SECTION B
Q2 (a) There are several testing at site during site investigation work such as
Standard Penetration Test (SPT), Cone Penetration Test (CPT), vane shear test
(VST), plate bearing test and others.
(i) Briefly explain the objective to carry out plate bearing test?
(2 marks)
(ii) List THREB (3) in-situ testing devices which may require boreholes
prior to testing and explain why boreholes are required for these tests.
(6 marks)
(b) In sampling process, there are two types of sample, i.e. disturbed and
undisturbed sample.
(iii) List TWO (2) laboratories testing for undisturbed samples and
THRBE (3) laboratories testing for disturbed samples.
(5 marks)
BFC 4043/BFC 43103
(b) Recalculate the design bearing capacity for the condition of Q3 (a) but with
the ground water table at a great depth and assuming that the bulk unit weight
of the soil above the water table is I 8 kN/m'.
(6 marks)
(6 marks)
(b) A 3 x 2 pile group with a pile center-to-center spacing of 1.2 m and pile
diameter of 0.4 m supports a load of 3000 kN as shown in Figure Q4 (b).
Determine:
(15 marks)
4
BFC 4043/BFC 43103
Qs (a) Briefly explain the stability against heave in retaining structure analysis.
(3 marks)
(c) Explain the difference between free earth support and fixed earth support
method in design and analysis of sheet-pile.
(4 marks)
(d) Figure Q5 (d) shows an embankment for road construction which should be
reinforced by metallic strip steel, the size of strip is (5 x 100 ) mm and
allowable pull out strength: 250 Mpa
(i) Sketch the active earth pressure which develop at the sides of this
embankment
(6 marks)
(ii) Design the vertical and horizontal spacing, and length arrangement of the
strip reinforcement. The safety factor against pull-out is required2.
(9 marks)
BFC 4043/BFC 43103
SEKSYEN A
Sl (a) Secara ringkas, bincangkan SATU (1) teknik modifikasi secara mekanikal dan
SATU (1) modifikasi secara hidraulik untuk pembaikan tanah.
(6 markah)
(b) Nisbah lompang, e, di tapak tanah pinjam ialah 0.72. Lubang tanah pinjam
perlu dikorek dan dihantar ke tapak bina bagi tujuan kambusan yang mana
ianya perlu dipadatkan kepada nisbah lompang 0.42. Projek pembinaan
tersebut memerlukan 10,000 m3 bagi kambusan tanah terpadat.
Tentukan isipadu tanah tersebut yang perlu dikorek dari lubang tanah pinjam.
(5 markah)
(c) Berpandukan kepada Rajah Ql (c). Bagi operasi kambusan yang banyak,
purata beban kekal [Ao'(p)] pada lapisan tanah liat akan meningkat sebanyak
57 .5 kN/m'. Purata tekanan tanggungan berkesan pada tanah liat sebelum
operasi kambusan ialah 71.88 kN/m'. Pada lapisan tanah liat, yang mana ianya
mengalami terkukuh normal dan tersalir secara ke atas dan ke bawah,
diberikan H.: 4.57 ffi, C.:0.30, eo: 1.0, cn:9.68 x l0-2 c^21^in Tentukan
perkara yang berikut:
(i) Enapan pengukuhan primer pada bahagian tanah liat yang disebabkan
oleh pertambahan tekanan kekal, Ao'o).
(2 markah)
SEKSYEN B
52 (a) Terdapat pelbagai ujikaji di tapak semasa penyiasatan tapak seperti Ujikaji
Penusukan Piawai (SPT), Penusukan Kon (CPT), Ujian Ricih, Ujian Plate
Be ar ing dan sebagainya.
(6 markah)
(b) Dalam proses pensampelan, terdapat dua jenis sampel. Sampel tersebut adalah
sampel terganggu dan sampel tidak terganggu.
(iii) Senaraikan DUA (2) ujikaji makmal untuk sampel tak terganggu dan
TIGA (3) untuk sampel tanah terganggu.
(5 markah)
BFC 4043/BFC 43103
S3 (a) Bangunan sediakala akan dijalankan pengubahsuaian. Salah satu asas tapak
tersebut mempunyai keluasan 1.5 m X 1.5 m dan sedalam I meter daripada
permukaan tanah. Perubahan struktur bangunan tersebut memerlukan asas
tapak yang dapat menanggung beban sebanyak 2,000 kN. Penyiasatan tapak
menunjukkan tanah dibawah asas tapak adalah pasir sederhana tumpat dan
tumpai. Sudut ricih tanah adalah 346, danberat unit tepu adalah 19 kN/m3.
Penyiasatan tapak j.rga menunjukkan paras air bumi adalah pada paras asas
tapak tersebut. Tanah sekeliling asas tersebut mempunyai kepadatarr yang
tinggi supaya faktor kedalaman boleh diambilkira. Kiraan adalah
menggunakan persamaan keupayaan galas umum dan factor keselamatan2.S
(14 markah)
(b) Kirakan semula rekabentuk keup ayaan galas mengikut keadaan seperti dalam
53 (a) di atas tetapi paras air bumi adalah sangat dalam dan anggarkan
bahawa berat unit gembur tanah di atas paras air bumi adalah 18 kN/m'.
(6 markah)
(c) Bincangkan tujuan amalan dalam seliaan pembinaan asas oleh pegawai
yang berpengalaman dengan faktor-faktor yang digunapakai dalam membina
rekabentuk asas.
(5 markah)
(6 markah)
(b) Sebuah cerucuk berkumpulan dengan dimensi 3xZ,jarak pusat ke pusat l-2 m
antara satu dengan yang lain dan berdiameter 0.4 m menanggung beban
seberat 3000 kN seperti Rajah Q4 (b). Tentukan:
(15 markah)
BFC 4043/BFC 43103
(b) Terangkan anjakan ufuk muktamad dari struktur penahan, dan kaedah
mengatasi kriteria ini dalam rekabentuk.
(3 markah)
(c) Terangkan perbezaan antara sokong tanah bebas dan sokong tanah tetap dalam
rekabentuk dan analisa cerucuk keping.
(4 markah)
(d) Rajah Q5 (d) menunjukkan timbusan tanah untuk pembinaan jalan raya yang
akan diperkuat dengan keluli jalur bersaiz 5 x 100 mm dan kekuatan tarik yang
dibenarkan adalah 250 Mpa
(i) Lukis tekanan tanah aktif yang wujud pada tepi timbusan
(6 markah)
(ii) Rekabentuk spasi I ruang pugak dan ufuk, dan panjang keluli jalur.
Faktor keselam atan terhadap tarik diperluk an adalah 2.
(9 markah)
BFC 4043/BFC 43103
FINAL EXAMINATION
relll' t:;i:TlT..
'YVm
tl
'r .'..: At*, +
:ertable""
Groundwater table | "'I Arig-
lAor,+Ao1i,l-
"-'.:-
. vsrrv
l;T:;- | t
tnd ; '.. ,'_..
i,
|
i
I
ar4pr
Time
iiiriiii
I
ffiN
I
l, Time
i-t
1Hvi:iri"#i'l ffi I
I
I ls. *,
S*,u *1,
ts
q
'.. .i"'.'",:'_.' .
."" '.-' t,.':
Sand .:..'.".'-'..
{a}
I
Settlement ((b)
b)
Fieure Ol (c)
kN/m2 t
.__l
tl
100
rl
5m
I r=18kN/m3 |
I c=25kN/;' n
rl
v I
tl| ,=22kN/m3
,no
t
|
|/*\
c=20kN/m2
I o=30'
_Y_ ----------l\
30
Fieure 02 (a)
l0
BFC 4043/BFC 43103
FINAL EXAMINATION
ooq
l oe
Q: 3000kN
I Sand
kJv
15,5
*r,
Ground water table
Normally Consolidated
Clay
nF Lt,rai
{sat --1'takff
C : 0.25
"
o : 0.75
Fieure 04 (b)
1t
BFC 4043/BFC 43103
FINAL BXAMINATION
q,:2 kN/m2
T =l8kN lm3
Q
:35"
c:25 kPa
c: 15 kPa
T =l6kN lm3
Q =30'
Fieure O5 (d)
T2
BFC 4043/BFC 43103
FINAL EXAMINATION
Table I
ut%l r, U l7ol T, U l7sl T, ul%l T,
30 o.o:114 46 0"166
a4
0.431 98 1500
al
2l r).0346 47 0.r73 IJ $.446 99 1.781
'|"1 0.0:380 48 o.181 T4 r).46I t00 T
?3 o.0415 49 $- 188 ?5 0.477
?4 o.0+53 5{) 0.197 76 CI.4e3
'){ 0.0491 5I 0.3s+ "t7 o.5t1
l3
BFC 4043/BFC 43103
FINAL EXAMINATION
Formulae
I+eo oo Hr,
D^
fr=a '! -b
su.,
t,
A*(%)=Lf(roo) = 0.2gN60032
Po
ocR=o rrr[#)""
D,(o/o) =
D,(%)=l#1",,00,
t4
BFC 4043/BFC 43103
FINAL EXAMINATION
n - qk,H +)yH'k"
1
sin'Bsin(F-s')[t.
1^
/.
]'
Po =
|fi'4 -2c' H JC l+sin$ I
L
2c'
l-sinQ ko
-(
ry
.l
Shape Factor:
Qu
: l.3cN, + QN q + 0.4yBN, (square foundation) Fn,
qJL=t* ltan0
R
15
BFC 4043/BFC 43103
FINAL EXAMINATION
Formulae
h Factor
D.
If '>l:
B
for$:0o
F,a=l+0.4tan
Frl:l
Fra =l
for$>0o
l- F*
F,a = Fna -," #il
, D,
Fra =l + 2tan 0'(l - sin Q'f
Fra = | + 2tan Q'(t
;
- sin Q')'
Fra =l
Inclination Factor
l6
BFC 4043/BFC 43103
FINAL EXAMINATION
Formulae
Qp
: 0.4 poNoo (LD) S 4 po Noo
Q,: pLf'" * *
(so = 0rs/{{B6t eriXirgt e1i}J
oo 'SrS,
T7
BFC 4043/BFC 43103
FINAL EXAMINATION
l8
BFC 4043/BFC 43T03
FINAL EXAMINATION
0 5.14 1.00 0.00 0.20 0.00 26 22.25 11.85 L2.54 0.53 0.49
1 5.38 1.09 0.07 0.20 0.02 27 23.94 13.20 L4.47 0.55 0.51
2 5.63 L.20 0.15 0.2t 0.03 28 25.80 t4.72 t6.72 0.57 0.s3
3 5.90 1.31 0.24 0.22 0.05 29 27.86 L6.44 L9.34 0.59 0.55
4 5.19 1.43 0.34 0.23 0.07 30 30.14 18.40 22.40 0.61 0.58
5 6.49 1.57 0.45 0.24 0.09 31 32.67 20.67 25.99 0.63 0.60
6 6.81 L.72 0.57 0.2s 0.11 32 35.49 23.18 30.22 0.65 0.62
7 7.t6 1.88 0.7r 0.26 0.12 33 38.64 26.09 35.19 0.68 0.65
8 7.53 2.06 0.86 0.27 0.14 34 42.t6 29.44 41.06 0.70 0.67
9 7.92 2.25 1.03 0.28 0.16 35 46.t2 33.30 48.03 0.72 0.70
10 8.35 2.47 L.22 0.30 0.18 36 s0.59 37.75 56.31 0.75 0.73
11 8.80 2.71 L.44 0.31 0.19 37 55.63 42.92 66.19 0.77 0.75
t2 9.28 2.97 1.69 0.32 0.21 38 61.35 48.93 78.03 0.80 0.78
13 9.81 3.26 1.97 0.33 0.23 39 67.87 55.96 92.25 0.82 0.81
t4 t0.37 3.s9 2.29 0.35 0.2s 40 75.3t @.20 109.41 0.85 0.84
15 10.98 3.94 2.65 0.36 0.27 4L 83.86 73.90 L30.22 0.88 0.87
11.63 4.34 3.06 0.37 0.29 42 93.71 85.38 155.55 0.91 0.90
16
0.39 0.31 43 105.11 99.02 186.s4 0.94 0.93
t7 L2.34 4.77 3.s3
13.10 5.26 4.07 0.40 0.32 44 118.37 115.31 224.64 0.97 0.97
18
s.80 4.68 0.42 0.34 45 133.88 134.88 27r.76 1.01 1.00
19 13.93
6.40 5.39 0.43 0.36 46 152.10 158.51 330.35 1.04 1.04
20 14.83
7.07 6.20 0.45 0.38 47 L73.64 L87.21 403.67 1.08 L.07
2L 15.82
22 16.88 7.82 7.13 0.45 0.40 48 L99.26 222.3t 496.01 t.r2 1.11
8.20 0.48 0.42 49 229.93 255.51 513.16 1.15 1.15
23 18.05 8.66
L9.32 9.60 9.44 0.s0 0.45 50 266.89 319.07 762.89 1.20 1.19
24
25 20.72 10.66 10.88 0.51 0.47
t9