1 The Point at which the magnums in a matzrial can not be increased even those magnetizing
force continues to increase known as the?
A Salient pole
B Saturation point
C Residual point
DRemnant point
2.Which type of current has “skin effect” 2
A.Ac
BDe
C.Half-wave rectified
D.Full-wave rectified
3. Which of the following is most of ton used for dry magnetic particle inspection ?
A. Full cycle De
B. Half weave Rectified Alternating current (HWAC)
C. High voltage low amperage current
D. Direct current from electrolytic cells
4, The area of maximum induced filed strength using a yoke is ?
‘A. Atthe north pole of yoke
B, Atthe south pole of yoke
C. The area directly between the pole
D. On the outside of potes pieces
5. Demagnetization ?
A. may be accomplished by heating a material above its curie points
B. It always necessary
C. Can be performed only with Ac
D. Can be performed only with De
6. Coercive Force ?
‘A. Describes the means by which the magnetic particles are suspended in the liquid
when using wet method
B, Describes the magnetizing force used with the continuous method
C. Represents the reverse magnetizing force necessary to remove the residual
magnetism in a material
D. Is not a term used in magnetic particle testing
17, If an overall pattern appears on the test surfaces how should the inspector re-process
the test piece ?
7 & Resestat higher amperage
B. Demagnetize
C. Re-test at lower amperage
D. Both a&b
8. Which of following can cause non relevant magnetic particle indication ?
A. Joints between dissimilar metals
B. Brazed joints
C. Roughing tool cuts on surface
D. Allof the above
9. When the most complete demagnetization available is described and demagnetization
is to be accomplished by placing the part in a coil energized with AC of progressively
decreasing amperage the following orientation of the long axis of the part is most
desirable
A. East-West
,__B. North-South
7G. South-West
D. North-East
10. Non relevant indication due to residual local poles interface with magnetic particle
testing for a successful examination one should
A.Use more amperage
B, Demagnetize then remagnetize in the desired direction
C. Use lower amperage
E, Magnetize in another direction
11.A cylindrical part is to be tested using circular magnetization .the part has three
different diameter along its length a rule-of-thumb for current values for each diameter
provides three level the current value that should be applied first is
A. The highest value
B, The median value
C. The lowest value
D. It is dose not matter which is applied first
27
12. A five turn coil will be used an a part that is 18”*long (457mm) and 1.5”*dia (38mm)
what is L/D ratio of the part if SOO0A of magnetizing currents is used
A. 90
® 12
C. 16.5
D.18
E. None
13. Unit of viscosity
see
» A. Tesla - ret a
B. Centistokes — 3 ar &
C. Gausses
14,Which of the following is false concerning a magnetic field in and around a hollow
conductor as compared to that of a solid conductor as compared to that of a solid
conductor of same outside diameter when both are same magnetic material and when the
applied current is same
A.The field outside the outer surface of the hollow conductor is greater
B.The field gradient inside hollow conductor is Steeper
C.The field outside the conductors are the same
D.The field of the same at the center
15.A seam welded pipe that had the weld ground flush showed BROAD FUZZY.
indication wear toes of the weld that extended to complete length of pipe the probable
cause of the indication is
A. Magnetic writing
B. The geometry of the weld
C. A surface crack
D. A permeability change in the base metal af the HAZ
16. A group of indication some sharp and some BROAD AND HAZY were found on an
1g demagnetization and retesting eliminated these indication the
probable cause was
A. A forging lap
B. Magnetic writing
C. A change in permeability
D. Sub surface variation