Professional Documents
Culture Documents
MSB Part 9 Connections
MSB Part 9 Connections
Joint types are partial depth flexible end plates, fin plates, double angle cleats, column splices (bearing type) an
The workbook offers the alternative of different languages, and selection of National Annex values from the "
National Annex value may be overwritten, and default values may be stored
Basic selection of section type, section, grade of main member, plates and bolts is made on the "
Each joint type is covered on a different worksheet. The default connection detail will be the recommended stan
Connection details may be changed on each worksheet. The connection resistance will update.
The standardised details can be restored at any stage
A more detailed table of the resistance of each connection component can be viewed, and printed.
Some toolbars and features have been hidden - these will be restored as the spreadsheet closes.
The design guides have been prepared under the direction of Arcelor Mittal, Peiner Träger and Corus.
The technical content has been prepared by CTICM and SCI, collaborating as the Steel Alliance.
e with EN 1993-1-8
column splices (bearing type) and column bases
preadsheet closes.
S...
National Annex gM0 1 Spain 5 Español Netherlands
UK gM1 1 UK 6 English Poland
gM2 1.25 (1993-1-8) other 7 None Spain
gM2 1.1 (1993-1-1) UK
gMu 1.1 Country 6
● Use NA values
gc 1.5
Overwrite
factors 1
drop countyr UK 6
Na country UK 8
Section type
IPE
Section
Beam grade
S275
Plate grade
S275
Bolt grade
8.8
User
Project
Job Number
4 1
28 16 IPE 450
S235 2 S275
S275
S355
S460
UKB IPE 16
UKC 20
UK PFC 22
IPE 24
HE 27
HL 30
HD
UKB
2 S275
4.6 3 8.8
5.6
8.8
10.9
2 20
Top Bottom
Section type
HE
Section
Column grade
S355
Plate grade
S275 Cover plate thickness
10
Bolt Diameter
Number of rows
20
3
Connection Resistance
Cubrejuntas externos 1265 kN minimum (bolts in shear)
Inner plates 980 kN minimum (plate tension)
bolts in shear)
late tension)
4 1
top bottom
28 83 HE 260 B 82 HE 260 C
S235 3 S355
S275
S355
S460
top
1
1
2 0 2
UKC 16 2 20
IPE 20
HE 22
HD 24
HL 27
30
2
2 S275
4.6 3 8.8
5.6
8.8
10.9
Bolt Diameter Plate thickness
20 10
28 10 IPE 450
S460
1 1
2
2 20
Job number Design prepared 05/03/2010 11:15:45
Beta = 2/3, which assumes that the grout strength is at least 20% of the concrete strength, and
the thickness is no morethan 20% of the smallest plate dimension
It is assumed that the design bearing strength of the joint material fjd is equal to the design
bearing strength of concrete in compression, fcd. This means that (Ac1/Aco)^0.5 = 1.5
Whilst every effort has been taken to ensure that the calculations are correct, the user
must verify the output. Neither Arcelor Mittal, Piene Trager, Corus or its agents assume
responsibility for the appropriate use of this software.
gM0 =1
gM1 =1 UK NA to BS EN 1993-1-1:2005
IPE 450 S275
100 x 90 x 10 angle cleats 360 mm long
5 rows of M20 bolts 8.8 at 70 mm pitch
1 column of bolts at 55 mm backmark
Tying resistance
1069 kN - Bolts in shear
480 kN - Cleats in tension
1647 kN - Cleats - block tearing
1604 kN - Bolts in tension
759 kN - Beam block tearing
788 kN - Beam tension - net section
531 kN - Bearing in beam web
1271 kN - Bearing in angle cleats
Minimum 480 kN
Plate thickness Weld a = 5.6 mm
10 S235 2 S275
S275
S355
20 5 90 70
End
Plate width distance Offset UKB UKB 16 2 20
150 40 50 UKC 20
PFC(1) 22
IPE 24
PFC(2) 27
Connection Resistance 537 kN (shear resistance of beam web) EQA 30
Tying resistance 514 kN (end plate bending - Mode 1) UN_EQA
6
8
10
12
4 4
Bolt Diameter Angle thickness
20 10
28 10 IPE 450
Placa Placa
demasiado larga larga
demasiado
Lines of bolts Gauge Leg length Back mark
1 70 100 55 S235 2 S275
S275
S355
1 1 90
2
Plate thickness Concrete grade
20 30
Bolt Diameter
20
Length Pitch
650 550
Width Gauge
400 300
16 2
20
22
24
27
30
10 4
12
15
20
25
30
40
50
60
70
30
20
20
problem