Professional Documents
Culture Documents
Welding Procedure Qualification Certificate EN ISO 15614-1: 2017
Welding Procedure Qualification Certificate EN ISO 15614-1: 2017
Page 1 of 3
Other information
bs, ml
We confirm that the statements in this record are correct and that the test pieces were prepared, welded, tested and have fulfilled the requirements
with the above indicated code / testing standard.
Location: Piraeus, GREECE Date of Issue: 07 May 2018
Surveyor
N. PANTELIADIS
Hellenic Lloyd’s SA
Surveyor to Hellenic Lloyd's S.A.
LR031.2.2008
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as
'Lloyd's Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or
advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or
advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract.
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
Certificate no: PRJ11071220/21
Page 2 of 3
Manufacturer’s WPQR no.: - Method of preparation & cleaning: CUTTING & GRINDING
EVANGELOS SYRIGOS
Welder’s / operator’s name: Parent material specification: 1.4306 : EN 10027, 304L: SAE
(W01) (attach material certificates)*
Welding details
Type current / Wire feed Travel speed Heat input Metal transfer
Run Process Size filler Material Current [A] Voltage [V]
polarity m/min mm/min kJ/mm
1 141 1,6 100 17 DCEN - 109.1 0.94 -
2-3 141 1,6 60 11 DCEN - 116.7 0.34 -
Filler material designation & make: EN ISO 14343-A : W 19 9 L Si, AWS A5.9 : ER308LSi , RODDACCIAI
(attach consumable certificate(s))*
Any special baking or drying: N/A Weaving (max. with of run) weave bead
Gas / flux – shielding: ISO 14175:2008-I1-Argon Oscillation: amplitude, frequency, dwell time N/A
Gas / flux – backing: N/A Pulse welding details: N/A
Gas flow rate – shielding: 12 lt/min Distance contact tube / workpiece: 10mm
Gas flow rate – backing: N/A Plasma welding details: N/A
Tungsten electrode type / size: W 2.4 WTh20 red Torch angle: 60
Details of back gouging / backing: N/A Post-Weld Heat Treatment and / or Ageing: N/A
Preheat temperature: N/A Time, temperature and method: N/A
Interpass temperature: 200 ºC max Heating and cooling rates*: N/A
Post-heating: N/A
Power source: TIG CC
Manufacturer power source: KEMPPI
Other information*: ml
-
Manufacturer BELLOWS HELLAS O.E Surveyor
Manufacturer’s signature: N. PANTELIADIS
Hellenic Lloyd’s SA
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
Certificate no: PRJ11071220/21
Page 3 of 3
Test results
Tensile tests
Re Rm
Type / No 2 2 A% on Z% Fracture location Temperature: Remarks
N/mm N/mm
Requirements
Bend tests
Type / No Bend Angle Former Diameter Elongation Result
Values (J)
Notch location / direction Temp °C Average (J) Remarks
1 2 3
Other tests:
Type / Load: -
- H.A.Z.: Remarks*
-
- Weld metal:
Surveyor
N. PANTELIADIS
Hellenic Lloyd’s SA
LR031.2.2008
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.