Professional Documents
Culture Documents
MS 02 335 PDF
MS 02 335 PDF
com
■ Leak-tight gas seal with initial installation and with each reassembly
Features
The simple two-piece design of the Swagelok® medium-
pressure tube fittings and adapters consists of a female
fitting body and preassembled cartridge containing the Arbor
male nut and color-coded front and back ferrules on a Preassembled
disposable plastic arbor. The preassembled cartridge cartridge
ensures installers correct ferrule orientation, visual
confirmation of ferrule presence, and proper installation
into the female body. Components are released only
after the nut is threaded finger-tight on the fitting body. Female body
Male nut
Back ferrule
Gaugeable upon
initial installation
by torque or one
full turn Robust tube grip for a variety
of installation practices and
enhanced vibration protection
Female body
Front ferrule
Contents
Features ..................................................................................2
Pressure Ratings and Tubing Information .........................4
Materials of Construction.....................................................4
Cleaning and Packaging .......................................................4
Union, 6
Union, 5
Reducing Union, 6
Reducing Union, 5
Union, 7
Male Branch, NPT, 7
Male Connector—
Male NPT Thread, 5
Installation Instructions........................................................8
Replacement Parts .............................................................. 10
Nut and Ferrules Cartridge
Tools and Accessories ........................................................ 10
Gap Inspection Gauge
Pipe Thread Sealants
Preswaging Tool
Tube Benders
Tubing Products
Warranty Information .......................................................... 10
4 Medium-Pressure Gaugeable Tube Fittings and Adapter Fittings
Straight Fittings
Union
A Tube Dimensions, in. (mm)
D D OD Ordering
in. Number A D E F Fx
1/4 SS-4FK0-6 2.25 (57.2) 1.08 (27.4) 0.13 (3.2) 5/8 9/16
3/8 SS-6FK0-6 2.81 (71.5) 1.34 (34.0) 0.21 (5.3) 3/4 11/16
Fx Flat F Flat 1/2 SS-8FK0-6 3.36 (85.3) 1.59 (40.4) 0.28 (7.1) 1 7/8
E
Reducing Union
A Tube OD, in. Dimensions, in. (mm)
Dx D Ordering
T Tx Number A D Dx E F Fx G
3/8 SS-6FK0-6-4 2.64 (67.0) 1.34 (34.0) 1.08 (27.4) 3/4 11/16
Tx T 1/4 0.13 (3.2) 9/16
SS-8FK0-6-4 2.90 (73.8)
1/2 1.59 (40.4) 1.34 (34.0) 1 7/8
G 3/8 SS-8FK0-6-6 3.19 (81.0) 0.21 (5.3) 11/16
Flat F Flat Fx Flat
E
Bulkhead Union
A Dimensions, in. (mm)
D
Tube Panel Maximum
OD Ordering Hole Panel
in. Number A D E F Fx G Size Thickness
1/4 SS-4FK0-61 2.25 (57.2) 1.08 (27.4) 0.13 (3.2) 15/16 9/16 15/16 49/64 0.50 (12.7)
3/8 SS-6FK0-61 2.81 (71.5) 1.34 (34.0) 0.21 (5.3) 1 1/16 11/16 1 1/16 57/64 0.66 (16.7)
Fx 1/2 SS-8FK0-61 3.38 (85.8) 1.59 (40.4) 0.28 (7.1) 1 5/16 7/8 1 5/16 1 9/64 0.75 (19.0)
Flat F Flat E G Flat
E S
F Flat Fx Flat
Caps Plugs
A
D A
90° Elbows
Union
A Tube Dimensions, in. (mm)
D OD Ordering
in. Number A D E F Fx
1/4 SS-4FK0-9 1.26 (31.9) 1.08 (27.4) 0.13 (3.2) 5/8 9/16
E
3/8 SS-6FK0-9 1.58 (40.2) 1.34 (34.0) 0.21 (5.3) 3/4 11/16
F Flat 1/2 SS-8FK0-9 1.87 (47.5) 1.59 (40.4) 0.28 (7.1) 1 7/8
Fx Flat
Reducing Union
Tube OD, in. Dimensions, in. (mm)
Ax Ordering
Tx
T Tx Number A Ax D Dx E Ex F Fx G
Fx Flat 3/8 SS-6FK0-9-4 1.61 (40.9) 1.48 (37.5) 1.34 (34.0) 0.21 (5.3) 3/4 11/16
1/4 1.08 (27.4) 0.13 (3.2) 9/16
Dx SS-8FK0-9-4 1.69 (42.8)
A 1/2 1.91 (48.5) 1.59 (40.4) 0.28 (7.1) 1 7/8
G 1/2 SS-8FK0-9-6 1.82 (46.3) 1.34 (34.0) 0.21 (5.3) 11/16
Ex T
F
Flat
E D
Medium-Pressure Gaugeable Tube Fittings and Adapter Fittings 7
Tees
Union
A Tube Dimensions, in. (mm)
D F Flat OD Ordering
in. Number A Ax D E F Fx
E 1/4 SS-4FK0-3 2.51 (63.8) 1.26 (31.9) 1.08 (27.4) 0.13 (3.2) 5/8 9/16
3/8 SS-6FK0-3 3.17 (80.4) 1.58 (40.2) 1.34 (34.0) 0.21 (5.3) 3/4 11/16
1/2 SS-8FK0-3 3.74 (94.9) 1.87 (47.5) 1.59 (40.4) 0.28 (7.1) 1 7/8
Ax
Fx Flat
A
Ax
D
H Fx Flat
F Flat
Union Cross
Fx Flat
8 Medium-Pressure Gaugeable Tube Fittings and Adapter Fittings
Installation Instructions
Required Torque
Fig. 3 Tube Size
in. ft·lb N·m
fitting
1/4 25 35
3/8 45 60
1/2 110 150
tubing
Alternatively, mark the nut, then
tighten the nut one full turn.
shoulder
Fig. 4
Gaugeability
tubing On initial installation, the Swagelok medium-pressure gap
inspection gauge assures the installer or inspector that
a fitting has been sufficiently tightened.
Position the Swagelok medium-pressure gap inspection
Fig. 5 gauge next to the gap between the nut and body.
body
■ If the gauge will not enter the gap, the fitting is sufficiently
nut tightened (Fig. 6).
■ If the gauge will enter the gap, additional tightening is
required.
Fig. 6 body
nut
Swagelok
medium-pressure
gap inspection
gauge
Medium-Pressure Gaugeable Tube Fittings and Adapter Fittings 9
Reassembly Instructions
Fig. 7 Fig. 14
You may disassemble and reassemble the tube fitting
tubing with preswaging
preswaged
many times. tool
ferrules 1. Insert tubing with preswaged ferrules into the
nut
fitting body until the front ferrule seats (Fig. 7, 8).
body
2. Rotate the nut with a wrench and tighten to the
specified torque in the torque table (Fig. 9).
Alternatively, rotate the nut with a wrench to the
Fig. 8
previously pulled-up position; at this point a significant
nut increase in resistance will be encountered, then
tighten slightly with a wrench.
NOTE: Do not use a gap inspection gauge with
reassembled fittings.
Fig. 15
Fig. 9
Cap
Installation Instructions tubing with
nut
See medium-pressure tube fitting instructions preswaged
ferrules
(see page 8).
Plug
Installation Instructions nut
Hold the body steady and tighten the plug to the
specified torque. Alternatively, tighten the plug 1/4
turn from the finger-tight position. Fig. 16
Preswaging Tool
Fig. 10 tubing with
preswaging Installation Instructions preswaged
tool ferrules
1. Thread the preassembled cartridge (nut, ferrules,
and plastic arbor) into the preswaging tool until body
preassembled
cartridge finger-tight (Fig. 10).
2. Remove the plastic arbor (Fig. 11).
3. Insert the tubing into the preswaging tool (Fig. 12).
4. Make sure that the tubing rests firmly on the shoulder Fig. 17
Fig. 11 of the preswaging tool body (Fig. 13).
5. Hold the preswaging tool steady and tighten the nut
nut to the specified torque (Fig. 14). Alternatively,
mark the nut and tighten the nut 3/4 turn.
plastic 6. Loosen the nut.
arbor
7. Remove the tubing with preswaged ferrules from
the preswaging tool (Fig. 15). NOTE: If the tubing
sticks in the preswaging tool, remove the tubing
by gently rocking it back and forth. Do not turn
Fig. 12 the tubing.
preswaging 8. Insert tubing with preswaged ferrules into the
tool
fitting body until the front ferrule seats (Fig. 16).
9. Rotate the nut with a wrench and tighten to the
specified torque (Fig. 17).
tubing NOTE: Do not use a gap inspection gauge with fittings
that were assembled using the preswaging tool.
Fig. 13 shoulder
tubing
Replacement Parts
Nut and Ferrules Cartridge
To order replacement ferrules and nut, see ordering
information below. Each cartridge contains a front ferrule,
back ferrule, and male nut.