TROUBLESHOOTING
Re = aoa
Any discussion of drum end seal maintenance can be lengthy because of the wide variety
of seal designs used over the years by various rotary equipment manufacturers. The
designs are as simple as a piece of rubber belting or ceramic fiber blanket, or as elaborate
as utilizing counterweights, pulleys and air cylinders in an attempt to create a more
positive seal.
The primary purpose of any seal is to keep “tramp” air out of the unit to allow better control
of the process. A secondary but important function is to help control dust and hot gases
from escaping the kiln or dryer if there is some sort of “upset” condition.
For the purpose of this discussion maintenance issues of four common types of seals will
be reviewed. The four types are the graphite block seal, face plate type seals, the
‘outward facing leaf seal and the inverted leaf seal.
Shell Seals Section 5 p1OMMON CAUSES OF SEAL FAILURE
SION / CONTAMINATION
+ EXPANSION & CONTRACTION
(AXIAL MOVEMENT OF THE SHEL!
To be successful, the seal for a rotary kiln or dryer must accommodate both axial and
radial movement. The major downfall of most seals is moving parts that are susceptible to
“sticking” or failure from dust contamination or heat distortion. The three main causes for
seal failure are abrasion from product contamination, excessive shell run out in the seal
area, and expansion and contraction of the unit during operation.The graphite block seal has been around for many years with several variations. The
basic components of the seal are one or two rows of graphite blocks with one end of each
block contoured to fit the radius of the shell. The blocks are positioned radially in slide
holders that are spring loaded to keep them in contact with the shell. The graphite blocks
are staggered in the two rows with every other block overlapping. Many of these
installations have now been converted to some style of leaf seal
The graphite block seal is expensive because the main plate that the blocks ride on is
machined. This allows the blocks a smooth fiat guide surface but one which can be
distorted if it sees too much heat.The typical problems encountered with the graphite block seal are heat distortion of the
block holders, and dust accumulation causing the blocks to “bind” so they can’t move
freely in their respective slides. The result is that the springs can't keep the blocks in
contact with the shell. Another problem is spring failure. Various spring designs have been
tried with varying success.
Section 5 p4 Shell Sealsjht Apparatus
sure to keep Wear Plate in position.
FACE PLATE SEAL
Fixed Ring is attached to the Shell
and sotates with it.
Flexible Seal]
The face plate type of seal has many variations, but the operating principle of most of
them is the same and therefore the maintenance issues are similar, We will use the
arrangement shown in this illustration as an example for general discussion.
The main sealing components are a floating seal plate mounted on the face of the hood,
and a fixed seal plate that rotates with the shell. The floating plate has some type of
flexible section attached to it which allows the seal to move with the shell. The fixed and
floating plates have a wear plate segments made of AR plate, or brass or phenolic
material sandwiched between them and held in place with springs, counterweights or air
cylinders. Sometimes the rubbing surfaces are lubricated.
Contamination can cause this type of seal to stick. Typically the floating half gets stuck
and the sealing rings will disengage with any axial movement of the shell. Product may
also build up to the point that it deforms the flexible section of the pressure assembly
causing failure.COMMON PROBLEMS causing the face plate seal to leak and become ineffective:
Failure of the device applying pressure to the seal plates. The device should be inspected
regularly.
The wear plate will abrade and can only be replaced during a shut-down.
Excessive run-out in the shell. These types of seals are particularly susceptible to failure
if the shell run-out causes the fixed seal plate to “wobble”. The flexible assembly will allow
longitudinal movement but has difficulty to compensate for “wobble” of the rotating fixed
ring.ypical Non-Iinverted Kiln Seal
(Original design by WEBBCO)
‘Another common type of seal is the overlapping leaf seal originally design and patented
by WEBBCO. The two basic variations are outward-facing and inward-facing (inverted)
leaves. The principle of these seals is the same, the major difference being the direction
in which the leaves face. The drawback of the outward facing leaves is that they are
susceptible to damage from dust accumulation:
Most direct-fired units will operate with a slight negative pressure in the hood on which the
seal is mounted. An outward-facing seal acts to seat itself tighter against the shell with
that prevailing negative pressure. Hence, it creates a positive seal against infiltration of
ambient air which is the seal's intended purpose. However, most combustion is not
altogether “smooth” and flame turbulence, even on the best burners, will cause bumps
and puffs of positive pressure. The outward-facing seal has an inherent disadvantage
because the positive puffs blow the seal open allowing hot air and dust to blow out.Heat Distortion Material Packing Many Variations
SOME TYPICAL PROBLEMS
DAMAGE TO NON-INVERTED SEALS
The leaves should be made of a material that can withstand the temperature extremes to
which they will be subjected and still maintain spring pressure without taking a permanent
set. The leaf spring should also exhibit some abrasion resistance to provide an adequate
service life. The major drawback of the outward-facing leaf design is their susceptibility to
damage from dust accumulation. The lack of a substantial diversion hopper is a serious
limitation in this example.
Section 5 p8 Shell Seals.ingests
INVERTED SEAL
The spring action of the individual spring plates is strong enough to hold against the
negative operating pressure in the firing hood. The first advantage of the inverted seal is
that a positive puff will act to tighten up the seal, preventing blow-back. With no blow-back
there is no hot air flow, dust cannot be conveyed through the seal, and dust accumulation
is significantly reduced.
‘Secondly the seal leaves run on the riding band instead of directly touching the kiln shell.
This provides a sacrificial member if wear occurs. The riding band is mounted in such a
way to negate shell run-out at the time of installation.
Since the shell run-out has been all but eliminated the flexing of the seal leaves is
minimized thereby extending their service life.
Shell Seals Section 5 p9The seal is equipped with a “stub” hopper.
The seal is an air seal not a material seal. Nevertheless occasional spillage is expected
so a means of removing spillage must be provided. The stub hopper, which is supplied
with the seal, is a transition between the open bottom of the seal and some type of
conveyor (supplied by others) to remove the the spillage.
The conveyor can be a simple material chute, provided enough headroom is available to
use gravity or can be as elaborate as an enclosed drag chain in case of limited head room
as shown here. The installation shown at the right was installed on a 17’ (5 meter)
diameter kiln with only 30" (76cm) clearance from the shell to a concrete floor.
Section 5 p10 Shell SealsKiln Shell
Riding Band
Seal Leaves
A ‘worm's" eye view inside the hopper reveals the third advantage of the inverted seal.
The seal plates are above the hopper, which carries away product spillage. Unlike the
non-inverted seal, which “catches” product spillage, the inverted seal does not create a
shelf on which product can accumulate.
Phillips recommends spraying a graphite powder onto the riding band under the leaves to.
lubricate them whenever possible. This will help extend their service life.
Shell Seals Section 5 p11The inverted leaf seal does have a space requirement but the real plus of the inverted seal
is its simplicity of design. There are no moving parts to “stick”. The design incorporates a
method to keep the dust buildup away from the sealing components and itis very forgiving
of shell run-out.pais eae
SAFETY ISSUE
ENVIRONMENTAL ISSUE
Operating a kiln or dryer with ineffective seals or no seal costs money in wasted fuel due
to inefficient burning. Also, during an upset condition, puffs of hot gases and product can
become a major safety issue as well as an environmental problem.
Sheil Seals Section 5 p13ASE STUDY - M/s Maihar Cement
INEUMATIC SEAL
}d 12 electrically activated compressed air cylinders.
steel wear plate - replaced every 6-8 months.
Run outs created gap between plates.
between plates caused extensive damage.
Lubricated with grease.
Oxygen content = 2.7% at riser duct.
THE INVERTED SEAL
Overlapping full hard stainless steel leaf plates.
CONCLUSIONS
2.3 T COAL SAVING PER DAY = $22,000 PER YEAR
CASE STUDY
In Unit | of M/s Maihar Cement, two kilns (3 pier each) of 4.35M diameter x 64M length are
in operation. Both kilns were equipped with pneumatic plate-to-plate seals at the feed
end
The rotating wear plate was mounted on the kiln flange. Pneumatic cylinders were
mounted on the stationary plate. Pressure was applied against the smoke chamber plate
to force the stationary plate to move in an axial direction to come in contact with the
rotating plate. To reduce wear on both plates, a grease pump provided grease lubrication,
The seals demanded high maintenance and operational costs.
The inverted leaf seal replaced the pneumatic seals, installed in November 1997 and
August 1998. Operational efficiency of the kilns was improved; air ingress was reduced
and out-going dust was captured. There has been no maintenance cost on the seal to
date (1997 - 1998). Plant operators have calculated that they have saved $22,000 in fuel
costs in one year.