Professional Documents
Culture Documents
______________
OR
(c) Determine the total cost of 400 C.I. pulleys of 1000 cm3 volume. Consider 07
(1) Pattern cost = Rs. 700 , (2) Cost of C.I. = Rs. 20/kg., (3) Wages to the
moulder = Rs. 60 / day (4) No.of moulds prepared = 25/day/moulder, (5)
forging scrap
Process from 9= cm.
10 %diameter bat stock.
of Net weight (6) Cost of process scrap = Rs. 4/kg., (7)
Melting charges = 20% of material cost (8) Overhead charges = 25% of
material cost (9) Density of C.I. = 7.8 gm./c.c. Also find the rate of casting
per k.g.
(ક) 1000 cm3 ની C.I. ની 400 પુલી મ ટે નો ખર્ચ શોધો. (1) પેટનચ ખર્ચ = Rs. ૦૭
700 , (2) C.I ની કકિંમત = Rs. 20/kg (3) મોલ્ડર નુ મહેંત ણુ = Rs. 60 / day
(4) મોલ્ડ ની સાંખ્ય = 25/કદવસ/મોલડર (5) પ્રોસેસ સ્રેપ = 10 % નેટ
વજન (6) પ્રોસેસ સ્રેપ ની કકિંમત = Rs. 4/kg (7) મેલ્ટીંગ ર્ જીસ =
મટીરીયલ કકિંમત ન 20 % (8) ઓવરહેડ ર્ જીસ = મટીરીયલ કકિંમત ન 25
% (9) C.I ની ઘનત = 7.8 gm./c.c છે . પ્રશત કકલોગ્ર મ ક સ્ટીંગ નો ખર્ચ
પણ શોધો.
પ્રશ્ન. ૪ (a) State the steps of calculating shaping operation time. 03
3/4
(બ) એક C.I બ્લોક 10 cm X 3 cm ની ઝ ડ ઇ બે કટ મ ાં 1.8 cm થી 1.3 cm ૦૪
ઘટ ડવ મ ાં આવેછે. જો કટીંગ સ્પીડ 20 m/min , ફીડ 0.2 mm/stroke અને
કટીં ગ સમય = 3/5 કુલ સમય હોય તો શેપીંગ નો સમય શોધો.
OR
(b) A slot of 2cm deep and 10 cm long is to be cut in a M.S. job, using a milling 04
cutter of 8 cm diameter and rotating at 120 rpm.If milling is to be done in two
cuts and feed is 0.05 cm/rev, find the time required.
(બ) 120 rpm પર ફરતી 8 cm વ્ય સવ ળી એક મીલીંગ કટર વડે એમ.એસ. જોબ ૦૪
મ ાં 2cm ઉંડો અને 10 cm લ બ
ાં ો ખ ર્
ાં ો ક પવ નો છે . જો શમલીંગ 2 કટ મ ાં
કરવ નુ હોય અને ફીડ 0.05 cm/rev હોય તો શમલીંગ સમય શોધો.
(c) The cost of active wheel washing powder packed in 1 kg. Pouch is Rs.26. 07
The plastic material for pouch cost Rs. 1 per pouch. An operator is packing
500 pouches in a shift of 8 hours. If operator is paid Rs. 150 per 8 hours shift.
Estimate pouch packaging cost assuming interest & depreciation. Power cost
per pouch is Rs. 0.15.
(ક) એક કકલો એક્ટીવ વ્હીલ વોશીંગ પ વડર ની કકિંમત રુ. 26 છે . પ ઉર્ મ ટે ૦૭
ન પ્લ સ્ટીક મટીરીયલ ની કકિંમત પ્રશત પ ઉર્ રુ. 1 છે . એક ઓપરે ટર આઠ
કલ ક ની શશફ્ટ મ ાં 500 પ ઉર્ પેક કરે છે . ઓપરે ટર ને રુ 150 પ્રશત 8 કલ ક
ચુકવવ મ ાં આવે છે . પ વર કોસ્ટ પ્રશત પ ઉર્ 0.15 રુશપય છે . તો વ્ય જ અને
ઘસ ર ને ધ રી પ ઉર્ પેકેજીંગ મ ટે નો ખર્ચ અંદ જો.
************
4/4
Seat No.: ________ Enrolment No.______________
OR
(c) Explain the effect of various parameters on break even point
બ્રેક ઈિન પોઈંન્ટ પર અસર કરતા પકરબળો સમજાિો.
Q.5 (a) Estimate the time required to drill 4 holes in C.I.Flange from the following data.
Hole length 20 mm,hole dia 12 mm, cutting speed 15mm/min and feed 0.2 mm/rev 07
કાસ્ટ આયનણ ની ફ્લેંજ મા ૦૪ કાર્ા પાડિા માટે નો સમય શોધો.જો કાર્ા ની લૂંબાઈ ૨૦ મીમી,
કાર્ા નો વ્યાસ ૧૨ મીમી ,કટીંગ સ્પીડ ૧૫ મીમી/વમવનટ અને ફીડ ૦.૨ મીમ્િી/રીિોલ્યુશન છે .
(b) Define Net Weight, Shape Weight ,Gross Weight, Tong loss 04
િર્ણિો નેટ િેઈટ,શેપ િેઈટ ,ગ્રોસ િેઈટ ,ટૂંગ વ્યય (લોશ)
(c) State six objectives of Budget 03
ુ લખો.
બજેટ ના કોઈ પર્ છ િેતઓ
Seat No.: ________ Enrolment No.______________
Q.3 (a) Explain estimation of flash loss and sprue loss in forging. 03
પ્રશ્ન. 3 (અ) ફોર્જ િંગ ફ્લેશ નુકશ ન અને સ્રુ નુકશ ન અંદ જ સમજાવો ૦૩
OR
(a) Explain various forging operations. 03
(અ) યવયવધ ફોર્જ િંગ ક મગીરી સમજાવો ૦૩
(b) Explain various pattern allowances. 03
(બ) યવયવધ પેટનક એલ ઉંસીસ સમજાવો ૦૩
OR
(b) How to calculate turning time in machining shop? 03
(બ) મશીનીંગ શોપ મ ટે ટયનિંગ સમય કે વી રીતે ગણી શક ય ૦૩
(c) A square bar of 25mm sides is to be produced from a round bar of 04
25mm diameter and 500mm length. Considering only 5% scale loss, calculate
the length of square bar produced.
2/4
(ક) 25 મીમી વ્ય સવ ળ અને 500 મીમી લમ્બ ઇ વ ળ ર ઉંડ બ ર મ થી 25 ૦૪
મીમી
મીમી બ
બજજુુ વ
વ ળો
ળૉ ચોરસ
ચોરસ બ ર િંગ
ફોર્જ બનથીવબન
મવટે જોમસ્કે
ટે લજોલોસ 5% હોય તો ચોરસ
સ્કેલલોસ્સ
બ ર ની લમ્બ ઇ કે ટલી થશે.
OR
(c) Determine time required for preparing M.S. bolt M20 x 3 mm by single point 04
cutting tool with a cutting speed 8m/min and length of threaded portion is
40mm. Consider No.of cuts required for threading is 8.
(ક) M20 x 3 મીમી સ ઇજ નો બો્ટ કટીંગ ટુલ વડે 8m/min ની કટીંગ સ્પીડ થી ૦૪
બન વ મ આવે છે .થ્રેડેડ ભ ગ ની લમ્બ ઇ 40 મીમી અને થ્રેડીંગ મ ટે લીધેલ
કટ ની સાંખ્ય 8 છે . તો આ મ ટે લ ગતો સમય શોધો.
(d) Estimate the time required to drill 4 holes of 1 cm diameter in a plate. Hole 04
depth is 2 cm, cutting speed is 15 m/min and feed is 0.01 cm/rev.
બનન વ મ આવે છે બ રબન વ મ અવે ચી. જો સ્કે લ લોસ 5%
(ડ) એક પ્લેટ મ કિલીંગ કરી 1 સેમી ન 4 હો્સ બનવ ય છે . જો હોલ ની ઉંડ ઇ 2 ૦૪
સેમી, કટીંગ સ્પીડ 15 મી/યમયનટ અને ફીડ 0.01 સેમી/ રીવ. હોય તો કિલીંગ
સમય શોધો.
OR
(d) A slot of 2 cm deep and 10cm long is to be cut in a M.S. job with a miling 04
cutter of 8 cm diameter & rotating at 120 rpm. If milling is done in 2 cut and
feed per revolution is 0.05 cm., then calculate the milling time.
(ડ) 8 સેમી વ્ય સ વ ળ મીલીંગ કટર થી એક M.S. જોબ મ 2 સેમી ઉંડો અને 10 ૦૪
સેમી લ મ્બો એક ખ ચ
ાં ો બન વ મ આવે છે . જો જોબ 120 rpm થી ફરતો હોય
અને કટ ની સાંખય 2 તથ ફીડ 0.05સેમી/ રીવ. હોય તો મીલીંગ સમય
શોધો.
Q.4 (a) Explain cost estimation per pouch for pouch packaging. 03
પ્રશ્ન. ૪ (અ) પ ઉચ પેકકિંગ મ ટે પ્રયત પ ઉચની કકમતનો અંદ જ સમજાવો ૦૩
OR
(a) List various cost elements of an ice plant. 03
(અ) આઇસ પ્લ ટ ાં કોસ્ટ ન જુદ જુદ તત્વો સમજાવો ૦૩
(b) Write down Steps for cost estimation for producing power using diesel 04
generating set.
(બ) ડીઝલ જનરે ટીંગ સેટ થી પ વર ઉત્પ દન ની કકમતનો અંદ જ મેળવવ ન ૦૪
પગથીય લખો
OR
(b) A thermal power plant produces 80 Mw to satisfy maximum demand. Load 04
factor of plant is 40%. Estimate power cost per unit for power produced by
this plant. Operating cost Rs. 1.94/kwh.(Assume capital cost as Rs.1800
per kw and depreciation is 12%).
(બ) એક થમકલ પ વર પ્લ ટ ાં મ મહત્તમ મ ગ ાં ને પુરી કરવ મ ટે 80 Mw પ વર ૦૪
ઉત્પન્ન કરવ મ આવે છે . લોડ ફેક્ટર 40% છે . જો ઓપરે ટીંગ કોસ્ટ Rs.
1.94/kwh હોય તો એક યુયનટ ન ઉત્પ દનનો ખચક શોધો કે પીટલ કોસ્ટ રુ.
18—પ્રયત kw તથ ડેપ્રેયસએસન અને વ્ય જ દર 12% ધ રો
(c) The cost of active wheel washing powder packed in 1 kg. pouch is Rs.26. The 07
3/4
plastic material for pouch cost Rs.1 per pouch. An operator is packing 500
pouch in a shift of 8 hours. If operator is paid Rs.150 per 8 hours shift.
Estimate pouch packaging cost assuming interest & depreciation. Power cost
per pouch is Rs.0.15.
(ક) એક્ટીવ વ્હીલ વૉશીંગ પ વડર ની 1 kg ની કકમત રુ. 26 છે . પ ઉચ મ ટે ન ૦૭
મટીરીયલની કકમત રુ. 1 પ્રયત પ ઉચ છે . ઓપરે ટર 8 કલ ક ની એક શીફ્ટ મ
500 પ ઉચ પેક કરે છે . આ મ ટે ઓપરે ટર ને એક શીફ્ટ ન રુ. 150
આપવ મ આવે છે . ડેપ્રેયસએસન અને વ્ય જ દર 12% ધ રો અને પ ઉચ પેક
કરવ ની કકમત પ્રયત પ ઉચ શોધો પ વર કોસ્ટ પ્રયત પ ઉચ રુ. 0.15 છે .
************
4/4
Seat No.: ________ Enrolment No.______________
Instructions:
1. Attempt all questions.
2. Make Suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Use of programmable & Communication aids are strictly prohibited.
5. Use of only simple calculator is permitted in Mathematics.
6. English version is authentic.
Q.2 (a) List and explain the assumptions made in breakeven analysis. 03
પ્રશ્ન. ર (અ) બ્રેક ઈવન એન લિર્સસ મ ટે ની ધરણ ઓ ાં િખી સમજાવવો. ૦૩
OR
(a) Explain procedure for constructing breakeven chart. 03
1/3
(અ) બ્રેક ઈવન ચ ટચ રચવ ની રીત સમજાવવો. ૦૩
(b) ‘Breakeven analysis is a management tool’-Explain it. 03
(બ) ‘બ્રેક ઈવન એન લિર્સસ એ મેનેજ્મેંટન ાં ટૂિ છે ’- સમજાવવો. ૦૩
OR
(b) Drive relation for profit-volume ratio. 03
(બ) પ્રોફફટ વોલ્ય ૂમ ન સાંબધ
ાં ન ાં સ ૂત્ર તરવો. ૦૩
(c) What is ‘margin of safety’ in breakeven analysis? 04
(ક) બ્રેક ઈવન એન લિર્સસમ ાં ‘સિ મતી ગ ળો’ સમજાવવો. ૦૪
OR
(c) Discuss effect of various parameters on the breakeven point. 04
પ્રશ્ન. 3 (અ) ફોર્જ થયેિ કમ્પોનેંટ ની કોસ્ટ કઈ રીતે અંદ જવ મ ાં આવે છે ,સમજાવવો. ૦૩
OR
(a) Drive formula for finding machining time for shaping operation. 03
2/3
(d) Estimate the time required for cutting 3 mm pitch threads on a mild steel 04
bar of 2.8 cm dia. and 8 cm long. Assume the cutting speed for
threading as 15 m/min
(ડ) મ ઈલ્ડ સ્ટીિ ન 2.8 સેમી ડ ય . અને 8 સેમી િાંબ ઈવ ળ બ ર મ ાં 3 ૦૪
મીમીર્પચ ન થ્રેs પ ડવ મ ટે નો સમય શોધો.થ્રેડીંગ મ ટે ની કફટિંગ સ્પીડ 15
મી/ર્મર્નટ ધ રો
OR
(d) Find the time required to drill 6 holes in a casted flange each of 1 cm depth, if 04
the hole dia is 1.5cm.Assume cutting speed as 20 m/min and feed as 0.02
cm/rev.
(ડ) એક ક સ્ટ કરે િી ફ્િેંજમ ાં ,1.5 સેમી ડ ય .ન ,1 સેમી ઊંડ ઈન 6 હોિ કરવ ૦૪
મ ટે નો સમય શોધો.કફટિંગ સ્પીડ 20 મી/ર્મર્નટ અને ફીડ 0.02 સેમી/આંટ
Q.4 (a) Give definition of contract and list various types of contracts. 03
પ્રશ્ન. ૪ (અ) કોન્ટ્ર ક્ટ ની વ્ય ખ્ય આપી જદ જદ કોન્ટ્ર ક્ટ ની ય દી બન વવો. ૦૩
OR
(a) What is tendering? Explain its types. 03
(અ) ટેં ડફરિંગ એટ્િે શ?
ાં તેન પ્રક રો ર્વર્ે સમજાવવો. ૦૩
(b) Write short note on Pattern Allowances. 04
(બ) પેટનચ એિ ઊન્સ ઉપર ટૂાંક નોંધ િખો. ૦૪
OR
(b) Explain cost estimation in (any one) 04
(1) Diesel generating set (2) ice plant
(બ) નીચેન મથી કોઈપણ એક ર્વર્ે કોસ્ટ એસટીમશન સમજાવવો ૦૪
(1) ડીઝિ જનરે ફટિંગ સેટ (2) આઈસ પ્િ ન્ટ
(c) List and discuss different methods of overhead allocation. 07
************
3/3
Seat No.: ________ Enrolment No.______________
Q.2 (a) Write down the difference between estimating and costing. 03
પ્રશ્ન. ર (અ) એસ્ટીમેટીંગ અને કોસ્ટીંગ વચ્ર્ે નો તફ વત સમજાવો. ૦૩
OR
(a) Explain Labour contract and Piece rate contrat. 03
(અ) લેબર કોંટ્ર ક્ટ અને પીસ રે ટ કોંટ્ર ક્ટ વવશે સમજાવો. ૦૩
(b) Write down the different welding techniques in gas welding. 03
(બ) ગેસ વેલ્ડીંગ કરવ ની જુદી જુદી રીતો નુ વણચન કરો. ૦૩
1/4
OR
(b) List the elements of cost in arc welding. 03
(બ) આકચ વેલ્ડીંગ મ ખર્ચ ન ઘટકો ની ય દી આપો. ૦૩
(c) Find selling price of a steel table if the prime cost 3000 tables is Rs. 04
1,50,000.Factory overheads are 60% of prime cost, administrative overheads
are 40 % of factory cost and selling over heads are 30 % of office cost, and
20 % profit on total cost.
(ક) સ્ટીલ ટેબલ ની વેર્ ણ કકિંમત શોધો. 3000 ટે બલ ની પ્ર ઇમ કોસ્ટ ૦૪
1,50,000 રુવપય છે , ફેક્ટરી ઓવરહેડ પ્ર ઇમ કોસ્ટ ન 60 % છે , વહીવટી
ઓવર હેડ ફેક્ટરી કોસ્ટ ન 40 % છે , અને વેર્ ણ ઓવર હેડ ઓકફસ કોસ્ટ
ન 30 % છે . તથ નફો કુલ કકિંમત ન 20 % છે .
OR
(c) A machine was purchased for Rs. 50,000. It was commissioned on 1st Jan 04
1992. The erection and installation charges are Rs. 5000.This machine was
removed on 31st Dec.2012. And its residual value is Rs. 15000. Find
Depreciation rate.
(ક) એક મશીન 50,000 રુવપય ની કકિંમતે ખરીદવ મ ાં આવ્યુ હતુ.ાં તેને 1લી Jan ૦૪
1992 ન રોજ ર્ લુ કરવ મ ાં આવેલ ુ છે .ઇરે ક્શન અને ઇંસ્ટોલેશન ખર્ચ રુવપય
5000 છે .આ મશીન 31 ડીસે. 2012ન દૂ ર કરવ મ આવ્યુ. તેની રે સીડયુઅલ
કકિંમત રુવપય 15000 કરવ મ ાં આવી છે તો ઘસ ર દર શોધો.
(d) Two 1 meter long M.S. plate of 1 cm thickness are to be welded by a lap 04
joint with 6mm electrode. Calculate the cost of welding. Consider current
used = 250 Amp. , voltage = 30 volts, welding speed = 10 m /hr, electrode
used = 0.1 kg/m of welding, labour charges = Rs. 5/hr, power charges = Rs.
10/ kW h , cost of electrode = Rs. 40 / Kg , Efficiency of machine = 60 %
(ડ) 1 મીટર લાંબ ઇ ની 1 સેમી જાડી બે એમ.એસ પ્લેટ લેપ જોઇંટ વડે 6 mm ૦૪
ઇલેક્ટ્રોડ ની મદદ થી વેલ્ડીંગ કરવ ની છે . તે મ ટે વેલ્ડીંગ ખર્ચ ની ગણતરી
કરો. તે મ ટે વીજ પ્રવ હ = 250 એમ્પીયર , વીજ દબ ણ = 30 વોલ્ટ,વેલ્ડીંગ
ઝડપ = 10 મીટર/કલ ક,ઇલેક્ટ્રોડ વપર શ = 0.1 કક.ગ્ર /મીટર વેલ્ડીંગ
,મજુરી દર = રુવપય 5 / કલ ક, પ વર ર્ જીશ = રુવપય 10/ kW h ,
ઇલેક્ટ્રોડ નો ભ વ = રુવપય 40/કક.ગ્ર .,મશીન ની ક યચદક્ષત = 60% છે .
OR
(d) A firm produces 1000 pens per day. The material cost is found to be Rs. 04
1600, the direct labour cost is Rs. 2000 and factory on cost chargeable is Rs.
2500. If the selling on cost is 40% of the factory cost, what must be the price
of each pen to release the profit of 14.6% of the selling price.
(ડ) એક પેઢી દરરોજ ની 1000 પેન બન વે છે . મટીરીયલ ખર્ચ રુ. 1600 ૦૪
છે .,ડ યરે ક્ટ લેબર ખર્ચ રુ.2000 છે .,અને ર્ ર્જ કરી શક ય તેવો ફેક્ટરી
શીરોપરી ખર્ચ.2500 છે .જો વેર્ ણ શીરોપરી ખર્ચ ફેકટરી કોસ્ટ ન 40 % હોય
તો દરે ક પેન પર તેની વેર્ ણ કકિંમત ન 14.6 % નફો મેળવવ મ ટે ની
વેર્ ણ કકિંમત શોધો.
Q.3 (a) Define (1) Shape weight (2) Net weight (3) Gross weight 03
2/4
પ્રશ્ન. 3 (અ) વ્ય ખ્ય આપો. (1) શેપ વેઈટ (2) નેટ વેઈટ (3) ગ્રોસ વેઈટ. ૦૩
OR
(a) List the various types of forging losses and explain any one. 03
(અ) ફ્રોર્જ િંગ લોસીસ ની ય દી આપો અને ગમે તે એક સમજાવો. ૦૩
(b) Determine the total cost of 400 pulleys of 1000 cm3 volume .Consider (1) 07
Pattern cost = Rs. 700 (2) Cost of C.I. = Rs. 20/kg (3) Wages of moulder =
Rs. 60/day (4) No. of moulds prepared = 25/day/moulder (5) process scrap =
10 % of Net weight (6) Cost of process scrap = Rs. 4/ kg , (7) Melting
charges = 20 % material cost (8) Overhead charges = 25 % of material cost
(9) Density of C.I. = 7.8 gm /c.c. find the rate of casting per kg.
(બ) 1000 ઘન સે.મી. કદ ની 400 પ ૂલી નો કુલ ખર્ચ શોધો. તે મ ટે (1) પેટનચ ૦૭
કોસ્ટ = રુ. 700 , (2) ક સ્ટ આયનચ ની કકિંમત =રુ. 20/કક.ગ્ર .,(3) મોલ્ડર નુ
વેતન= રુ. 60/કદવસ, (4) તૈય ર થત મોલ્ડ ની સાંખ્ય =25/કદન મોલ્ડર,(5)
પ્રોસેસ સ્રેપ = નેટ વજન ન 10%,(6) પ્રોસેસ સ્રેપ ની કકિંમત =
રુ.4/કક.ગ્ર .(7) મેલ્ટીંગ ર્ ર્જ= મટીરીયલ ખર્ચ ન 20 % (8) ઓવર હેડ
ખર્ચ= મટીરીયલ ખર્ચ ન 25% (9) ક સ્ટ આયનચ ઘનત = 7.8 ગ્ર મ/ઘન
સે.મી છે . તો દર કકલોગ્ર મ દીઠ ક સ્ટીંગ નો ખર્ચ શોધો..
OR
(b) 100 numbers of rings are to be forged from a soft steel rod of 1 cm diameter. 07
The ring has internal diameter of 8 cm and its outer diameter is 10 cm. If the
scale loss is 6% and shear loss 2mm of the length of rod for each ring , find
the total material cost if the rod is available at Rs. 3 per meter length.
(બ) 1 સે.મી વ્ય સ ન નરમ પોલ દ સલળય મ થ
ાં ી 100 કરિંગો ફોર્જ કરવ ની છે . ૦૭
રીંગ નો અંદર નો વ્ય સ 8 સે.મી અને બહ ર નો વ્ય સ 10 સે.મી. છે . જો સ્કેલ
લોસ 6 % હોય અને વશયર લોસ,દરે ક રીંગ મ ટે 2 મી.મી.જેટલી લાંબ ઇ નો
હોય તો કુલ મટીરીયલ ખર્ચ શોધો. સલળયો રુ.3 / મીટર લાંબ ઇ ન ભ વે મળે
છે .
(c) The total sales of an industry is Rs. 2,50,000.The fixed cost of the industry 04
is Rs. and variable cost is Rs. 1,25,000.Find the breakeven point for the
60,000
iindustry.
Industy.
(ક) એક
666666ઇન્ડસ્ટ્રી નુાં કુલ ર્ ણ રુ. 2,50,000 છે , ઇન્ડસ્ટ્રી ની કફક્સ્ડ કોસ્ટ
60 વે6666660,000 ૦૪
રુ . 60,000અને
66660ઊ છે અને ર્લલત ખર્ચ રુ. 1,25,000 છે . તો ઇન્ડસ્ટ્રી મ ટે બ્રેક ઇવન
નાં
નાંબ
બર ર શોધો.
શોધો.
OR
(c) Define following terms. (1) Breakeven point (2) Profit – volume ratio (3) 04
Fixed cost (4) Variable cost.
(ક) નીર્ે ન પદો ની વ્ય ખ્ય આપો. (1) બ્રેક ઇવન પોઇંટ (2) કફક્શડ કોસ્ટ ૦૪
(3) ર્લલત ખર્ચ.
3/4
Q.4 (a) Explain how will you estimate machine time in case of shaping and 03
planning operation.
પ્રશ્ન. ૪ (અ) શેપીંગ અને પ્લેનીંગ ઓપરે શન મ ાં મશીન સમય કેવી રીતે તમે અંદ જીત ૦૩
કરશો તે સમજાવો.
OR
(a) Define (1) cutting speed (2) depth of cut (3) over run. 03
(અ) વ્ય ખ્ય આપો. (1) કટીંગ સ્પીડ (2) ડેપ્થ ઓફ કટ (3) ઓવર રન ૦૩
(b) It is required to produce threads of 2mm pitch in a hole of 20 mm dia. and 04
20 mm depth by tapping. Taking three cuts and cutting speed of 5m/min for
M.S. Estimate the tapping time.
(બ) એક 20 mm વ્ય સવ ળ હોલ મ ાં 20 mm ઉંડ ઇ સુધી 2 mm પીર્ ન ઇંટનચલ ૦૪
થ્રેડ ટે પીંગ થી પ ડવ ન છે . ત્રણ કટ ગણી તથ કટીંગ સ્પીડ 5 મીટર/વમવનટ
લઇ ટેપીંગ નો સમય શોધો.
OR
(b) A steel rod of 60mm diameter and 120 mm length is to be reduced to 55mm 04
in one cut by turning. Its length is to be reduced to 100 mm. If cutting speed
is 25 m/min and feed 0.1mm/revolution, find the time required to finish the
job.
(બ) એક સ્ટીલ ન 60 mm વ્ય સ નો અને 120 mm લાંબ ઇ ન સલળય ને 55 mm ૦૪
વ્ય સ નો બન વવ નો છે અને લાંબ ઇ ઘટ ડી ને 100 mm કરવ ની છે . જો
કટીંગ સ્પીડ 25 m/min , ફીડ 0.1mm/revolution હોય તો જોબ ને કફવનશ
કરવ નો સમય શોધો.
(c) Write the procedure of estimating cost of power produced by diesel generating 07
set.
************
4/4
Seat No.: ________ Enrolment No.______________
1/5
OR
(b) Explain any two types of forging in details. 03
(c) A square bar of 2 cm side and 25 cm length is to be converted by hand forging 04
in to a bar of hexagonal section having each sides = 1 cm, calculate the length
of hexagonal bar produced. Consider scale loss to be 7% of total volume.
OR
(c) A round bar of 25 mm diameter and 500 mm length is being converted in to a 04
square bar of 25 mm sides by forging. Considering 5% scale loss only Estimate
the length of square bar formed.
(d) Calculate the cost of C. I. pulley of 1200 cm3 using material cost = Rs. 10 per 04
Kg, wages paid to the worker = 50 per day, density of C. I. = 8 gm per cm3,
overhead charges = 20% of material cost, melting charges = 20% of material
cost, number of mould prepared = 25 /day / molder.
OR
(d) Find the cost of C. I. pulley of 1000 cm3 .Take cost of cast iron = 25 Rs. / Kg 04
rate of molder = Rs.150/day, over head charges = 10% of material cost, total
number of moulds made = 30 / day / molder, density of casting = 7.2 gm / cm3,
molding charges = 15% of material cost.
Q.4 (a) A 15 cm long M.S. bar is to be turned from 4cm dia. In a single cut to 3.8 cm 07
dia. For first 5 cm length and to 3.4 cm for next 10 cm length. If cutting speed
is 45 m / min and feed is 0.02 cm / rev, and required setting and mounting time
of job in three jaw chuck is 45 sec, estimate the total time required for turning.
OR
(a) Estimate the time required to cut 6 threads per cm on a M. S. bar 20 mm 07
diameter for a length of 10 mm. Take cutting speed is 10 meter per minute and
assume 6 cuts.
(b) One ammonia refrigerant ice plant produce 160 kw refrigerating effect. 07
The heat rejection theoretically by evaporator is 1000 KJ / kg. Theoretical
compressor input is 185 KJ/kg. Mechanical efficiency of compressor is 85 %.
Actual heat absorption in cold chamber is 80 %. If Power cost per unit is Rs.
10 and labor cost is Rs 2000/day and overhead cost = Rs. 5000/day find out
ice production rate per kg. Plant is working for 24 hours.
Q.5 (a) List various types of budget. Explain any two in detail. 04
(b) Write difference between manual tendering and E – tendering. 04
(c) The market price of a lathe is Rs. 50000.The distributor is given 10 % 06
discount. Selling expenses are equal to factory expenses. If material cost, labor
cost and factory over heads are in the ratio of 1:4:2 and material cost is Rs.
4000, find the profit released on the lathe machine.
************
2/5
�ુજરાતી
પ�. ૧ દશમાંથી કોઇપણ સાતના જવાબ આપો. ૧૪
૧. એસ્ટ�મેટ�ગની વ્યાખ્યા .
૨. સ્ટ ્ર�ટ લાઇન મેથડથી ઘસારો શોધવા માટ��ુ �ુત્.
૩. ગેસ વે�લ્ડ�ગ માં વે�લ્ડ�ગકોસ્ટ ના ઘટકો ની યાદ� .
૪. બ્રેક ઇવન પો�ટ ની વ્યાખ્યા.
૫. ગમે તે બે ફો�જ �ગ ઓપર�શન �ુ વણર્ન કર.
૬. સ્થાયી ખચર્ અને અસ્થાયી ખચર્ ની વ્યાખ્.
૭. બ�ટ ની વ્યાખ્યાઆ.
૮. િવિવધ પ્રકાર ના ટ�ન્ડર ની યાદ� .
૯. �ુનીટ ર�ટ મેથડ થી શીરોપર� ખચર્ શોધવા�ુ �ુત્ર .
૧૦ ફો�જ �ગ મા સ્ક�લ લોસ �ુ વણર્ન ક.
પ�. ર અ સ્થાયી ખચર્માં વધારો કરતાં બ્રેક ઇવન પો�ટ ઉપર થતી અસર સ. ૦૩
અથવા
અ બ્રેક ઇવન ચાટર્ બનાવવા માટ� કરાતી ધાર િવષે જણાવો. ૦૩
બ એક ઉદ્યોગની �સ્થર ખચર્ની �ક Rs. 50000 છે . દર મ�હને 1000 નંગ ૦૩
ઉત્પાદન ક્ષમતા. દર�ક પ્રોડક Rs. 600 ની �ક�મતે વેચાય છે. પ્રોડકટ દ�
ચ�લત ખચર્Rs. 350 હોય તો બ્રેક ઇવન સંખ્યા શ.
અથવા
બ એના�લટ�કલ ર�તથી બ્રેકઇવન પોઇન્ટ શોધવા�ું �ુત્ર. ૦૩
ક આકર ્ વેલ્ડ�ગ ખચર્ને અસર કરતાં પ�રબળો જણ. ૦૪
અથવા
ક 25 cm X 25 cm X 25 cmની ઓપન ટ� ક ગેસ વેલ્ડ�ગમાંથી બનાવા માટ � ૦૪
વેલ્ડ�ગસમય શોધો. વેલ્ડ�ગ ફક્ત �દરની બા�ુએ કરવા�ું , 3 mm �ડ�
પ્લેટ માટ વેલ્ડ�ગ સ્પી12 િમિનટ/ િમટર વેલ્, ફ�ટ�ગ �ટ છાટ 10% ધારો.
ડ નીચેના પદોની વ્યાખ્યા આ. ૦૪
3/5
બ ગમે તે બે પેટનર્�ટછાટ�ું વણર્ન કર. ૦૩
અથવા
બ ગમે તે બે પ્રકાર ફોજ�ગ િવશે િવગતવાર વણર્ન કર. ૦૩
ક એક ચોરસ સ�ળયો ક� �ની બા�ુ 2 cm છે અને લંબાઇ 25 cm છે તેમાંથી ૦૪
હ�ન્ડફોજ�ગથી ષટકોણીય સળ�યો 1 cm બા�ુ વાળો બનાવવાનો છે . સ્ક�લ ઘટ
�ુલ કદના 7% હોય તો ષટકોણીય સળ�યાની લંબાઇ શોધો.
અથવા
ક ફોજ�ગ વડ� 25 mm વ્યાસના અને 500 mm લંબાઇવાળા ગોળાકાર ૦૪
સળ�યામાંથી 25 mm બા�ુ વાળો ચોરસ સળ�યો બનાવવામાં આવે છે . ફ્ક્
5% સ્ક�લ લોસ ગણી આ ચોરસ સળ�યાની લંબાઇ શોધ.
ડ 1200 ઘન સે.મી. ની. કાસ્ટ આયનર્�ુલી ની કોસ્ટ શ. તે માટ� મટ�ર�યલ ૦૪
ની �ક�મત = Rs. 10 / �કલો ગ્ર, મોલ્ડર�ું વેતન= Rs. 50 / �દવસ,
ઓવરહ�ડ ચાજ�સ = મટ�ર�યલની �ક�મતના 20%, મોલ્ડ�ગ ચાજ�સ=
મટ�ર�યલની �ક�મતના 20%, બનતા મોલ્ડરની સંખ્= 25 / �દવસ / મોલ્ડર
અને કસ્ટ�ગની ઘનતા= 8 ગ્રા/ સેમી3 લો.
અથવા
ડ 1000 સેમી3 ઘનફળ ધરાવતી C.I. �ુલી�ું ખચર્ શોધ. (પેટનર્ ક્સ્ટમર તરફ ૦૪
આપવામાં આવે છે ). તે માટ� કાસ્ટ આયનર્ની �ક�મ= Rs. 25 / �કલો ગ્ર,
મોલ્ડર�ું વેતન= Rs. 150 / �દવસ, ઓવરહ�ડ ચાજ�સ = મટ�ર�યલની
�ક�મતના 10%, મોલ્ડ�ગ ચાજ�સ= મટ�ર�યલની �ક�મતના 15%, બનતા
મોલ્ડરની સંખ્= 30 / �દવસ / મોલ્ડર અને કસ્ટ�ગની ઘનત= 7.2 ગ્રા/
સેમી3 લો.
પ�. ૪ અ એક 15 cm લાંબા એમ. એસ. બારને એક્જ કટમાં તેની5 cm લંબાઇ માટ� 4 cm ૦૭
વ્યાસમાંથી 3.8 cm વ્યાસ �ટલો અને બાક�ની 10 cm લંબાઇ માટ� 4 cm
વ્યાસમાંથી3.4 cm વ્યાસનો ટિન�ગ કર�ને ઘટાડવાનો છ. જો કટ�ગ સ્પીડ 30
m / min, ફ�ડ 0.02 cm / rev અને જોબને થ્રી જો ચકમાં સેટ�ગ તથા માઉન્ટ
કરવાનો સમય 45 સેકન્ડ હોય તો �ુલ ટિન�ગનો સમય શોધ.
અથવા
અ એક 20 mm વ્યાસના એ. એસ. સળ�યા ઉપર 10 mm લંબાઇમાં દર cm દ�ઠ ૦૭
6 થ્રેડ પાડવાનો સમય શો. કટ�ગ સ્પીડ10 m / min અને 6 કટ ધારો.
બ એમોિનયા ર��ફ્રજરન્ટવાળા એક આઇસ પ્લાન્ટ 160 KW ર��ફ્રજર�ટ� ૦૭
ઇફ�ક્ટ ઉત્પ� થાય . આ પ્લાન્ટના ઇવેપો ટર દ્વાર 1000 KJ / Kg �ટ્લી
ઉષ્મા સૈધાંિતક ર�તે ર��ક્ટ કરાય . સૈધાંિતક કોમ્પ્રેસર ઇન� 185 KJ / Kg
છે. પ્લાન્ટની િમક�નીકલ કાયર્ક્85%ની કોમ્પ્રેસર માટ� ગણતર�માં લેવા
છે. કોલ્ડ ચેમ્બરમાં એક્ચ્�ુઅલ હ�ટ એબ્સો 80%, થાય છે . પ્લાન્ 24
4/5
કલાક કાયર્રત રહ� છ . પાવર ખચર્ પ્રિત �ુિ Rs. 10 અને મ�ુર� ખચર્ Rs.
2000 પ્રિત�દન હોય તો અન્ય િશરોપર� ખ Rs. 5000 પ્રિત� ધાર�ને પ્રિ
�કલોગ્રામ આઇસ ઉત્પાદન ખચર્ �.
પ�. ૫ અ િવિવધ પ્રકારના બ�ટની યાદ� આપો અને ગમે તે બે �ું િવગતવાર વણર ૦૪
કરો.
બ મેન્�ુઅલ ટ �ન્ડર�ગ અને – ટ�ન્ડર�ગ વચ્ચેનો તફાવત લ. ૦૪
ક એક ઉદ્યોગની �સ્થર ખચર્ની �ક Rs. 50000 છે . દર મ�હને 1000 નંગ ૦૬
ઉત્પાદન ક્ષમતા. દર�ક પ્રોડક Rs. 600 ની �ક�મતે વેચાય છે. પ્રોડકટ દ�
ચ�લત ખચર્Rs. 350 હોય તો બ્રેક ઇવન સંખ્યા શ.
************
5/5
Seat No.: ________ Enrolment
No.___________
Q.4 (a) Define different operations performed on lathe machines and machining time 07
for each operation with some figure.
(b) Calculate the boring time for a C.I. cylinder to be machined in a single cut 07
which is 300 mm long and 200 mm internal diameter. Cutting speed is 12
m/min, Feed is 0.25 cm/rev, Approach and over travel is 0.5 cm each, Set up
time is 0.5 min.
OR
Q. 4 (a) Find the weight of 50 m long chain to be made from links of iron rod diameter 07
1 cm and weigh 6.6 gm/cm. I f the outer dimensions of a link are 10cm and 6
cm.
(b) Give definition of contract and its characteristics. 07
Q.5 (a) Give provision of different conditions in contract. 07
(b) Enlist benefits of budget. 07
1/3
OR
Q.5 (a) A thermal power plant produces 80MW to satisfy the maximum demand. Load 07
factor of plant is 40 %.Estimate power cost per unit for power produced by
this plant. Operating cost is Rs. 1.94/ kWh. Take capital cost per kW is Rs.
1800 and interest and depreciation at 12 %.
(b) Write the procedure of estimating cost of power produced by diesel generating 07
set.
************
ગુજરાતી
પ્રશ્ન. ૧ અ ઓવર હેડ એલોકે શન ની રીતો જણાવો અને મશીન અવર રે ટ ની રીત ૦૭
સમજાવો.
બ ઘસારા ફંડ અને ઓબસોલંસીસ વવષે સમજાવી ઘસારા ના પ્રકાર વવસ્ત્રુત રીતે ૦૭
સમજાવો.
2/3
પ્રશ્ન. ૪ અ લેથ મશીન પર થતા વવવવધ ઓપરે શન અને તે માટે લાગતા મશીનીંગ સમય ૦૭
શોધવાના સ ૂત્રો નાની આક્રુવત સહ જણાવો.
બ ૩૦૦મીમી લાંબાઅને ૨૦૦મીમીઅંદર ના વ્યાસ વાળા કસ્ટ આયકન ના નળાકાર ૦૭
નો બોરીંગસમય શોધો. Cutting speed is 12 m/min, Feed is 0.25 cm/rev,
Approach and over travel is 0.5 cm each, Set up time is 0.5 min.
અથવા
પ્રશ્ન. ૪ અ ૧૦×૦૬ મીમી બહાર ના માપ વાળી લોખંડ ની કડીઓ માથી ૫૦ મીટર લાંબી ૦૭
સાંકળ લોખંડના ૧૦ મીમી વ્યાસ વાળા સળીયા માથીબનાવવા મા આવે છે .જો
સળીયા ની ઘનતા 6.6 gm/cm હોય તો સાંકળનું કુલ વજન શોધો.
બ કોંન્ટ્રાક્ટનીવ્યાખ્યાઆપી તેની લાક્ષણીકતાઓ જણાવો. ૦૭
************
3/3