Professional Documents
Culture Documents
Optimize Thermal and Mechanical Design F PDF
Optimize Thermal and Mechanical Design F PDF
Exchangers
Webinar Q&A
This document summarizes the responses to questions posed before and during the webinar on general
Heat Exchanger Design topics. The topics have been arranged into four different categories:
2. Are there any recommendations for hydraulic aspects, optimum velocity in tubes, etc.?
EDR Shell & Tube provides a full Flow Analysis including RhOV2 calculations at the Shell &Tube
entrance and exit points and nozzles. Warnings will alert the user when calculated values exceed the
TEMA limit. Full documentation of our flow calculations—as well as a design guide for choosing
economic velocities for the tubeside and shellside streams—can be accessed with a subscription to
the HTFS Research Network.
Under Input > Program Options > Design Options >Process Limits the user can constrain the
design search by minimum and maximum velocities.
We provide two example files for thermosiphon reboilers. These examples are installed with Aspen
EDR and you can find them and other EDR Shell & Tube sample files at the following location in
Windows Explorer: C:\Program Files (x86)\AspenTech\Aspen Exchanger Design and Rating
V8.0\Examples\Shell&Tube.
5. What would be the recommended approach to modeling plate and frame heat exchangers if
EDR does not have built-in plate designs from vendors such as Alfa Laval?
You can use Aspen Plate Exchanger to design, rate, and simulate plate and frame, brazed plate, or
welded plate type exchangers. Aspen Plate Exchanger uses our own proprietary plate heat transfer
and pressure drop models and correlations. It is used by many customers as an independent
evaluation of vendor designs. This can be especially critical in two-phase applications.
6. Does EDR perform special code calculation, such as those required for graphite heat
exchangers?
ASME has new code calculations for graphite exchangers. If the market requirement is large
enough, we may add these to our mechanical products in the future.
8. How accurate are the calculated costs vs. actual costs in EDR?
This will depend on the specific cost factors that you use and how closely they match to the actual
fabrication cost. We do have fabricators who customize the labor rates, material costs, and other
database entries to get accurate cost figures. We have several standardized lists to choose from and
you can enter your own cost factors by opening the “Tools” menu and selecting “Costing Database”
(Figure 1).
Figure 1: How to enter your own cost factors
10. What steps do you take to reduce vibration and resonance issues in exchanger designs?
EDR does a full vibration and resonance analysis on tubes susceptible to vibration. On the
Tubesheet Layout diagram in the Mechanical Summary you can view which tubes were identified by
the program as possible vibration tubes. The Thermal/Hydraulic Summary shows the report of the
Fluid Elastic Instability and Resonance Analysis for each of these tubes. EDR vibration calculations
are based on HTFS methods or the TEMA Analysis can also be run. If any vibration indicators are
detected, this will be reported in the Warnings section as an Operation Warning.
Users can easily compare double-segmental baffles with single segmental; they can explore no-
tubes in window segmental baffles and specify additional supports. It may also be effective in some
cases to explore alternative shell configurations. You may like to view solution number: 130840,
Avoid Vibration Risks When Design Shell & Tube Exchangers (14:21). This shows a typical
approach to eliminating vibration risk in the design of an exchanger.
11. What is the purpose of the following calculation modes: Design, Rating, Find Fouling, and
Simulation?
Design Mode: Performs an extensive design search to find the best exchanger geometry to
achieve the specified duty. Requires a set duty and allowable pressure drops.
Rating/Checking Mode: The geometry and process conditions are specified by the user.
The program compares the area required to perform the duty with that specified in the input.
The main results are the area ratio (>1 the exchanger is over-surface, <1 the exchanger is
over surface). Some engineers use repeated rating calculations to manually find their choice
of design. If the area ratio is far removed from 1.0 then Simulation will provide more reliable
results.
Simulation: Considers the exchanger geometry to be fully specified and calculates the outlet
stream conditions that can be achieved in the exchanger from the specified inlet conditions.
Find Fouling: This calculation mode is similar to rating but adjusts the fouling resistance to
determine the maximum values which gives an area ratio of 1.
12. How do you generate plots of S&T heat exchanger performance in EDR? Can you generate an
overall schematic of several exchangers in series or parallel?
In the new Shell & Tube Console—V8 onwards—temperature profile plots for shellside and tubeside
are shown after each run.
You can also view detailed output from the Aspen Shell & Tube incremental calculations under
Results > Calculation Details > Analysis along the shell/ Analysis along the tubes. There is a
tab available where you can view plats of temperature, pressure, heat transfer coefficients, vapor
fraction etc. Currently there is no schematic of shells in series and parallel.
13. If I have a two-phase case (two-phase on both sides), how can I check the Heat of
Vaporization in the simulation? Can the EDR plot this?
Under the Overall summary, you will find a tabulation of the breakdown of heat load for a two-phase
case (Figure 2):
Under Results > Calculation Details > Plots > Analysis Along Shell/Tubes you can view plots of
specific enthalpy vapor fraction or heat load of the streams.
15. Does the exchanger rating also take into account seasonal variations in temperature of the
environment, as well as climatic variations of different countries?
Within EDR, you can set up thermal models in Rating or Simulation modes for different operating
conditions and track the results under Results > Results Summary > Recap of Designs. You may
also find it very useful to use Aspen Simulation Workbook with EDR to conduct case studies of this
nature—with EDR working within Microsoft Excel. Visit the Support site and view Knowledge Base
Item number 130667: Exploring multiple operating scenarios using Aspen Simulation Workbook and
Aspen Shell & Tube Exchanger.
With your EDR models embedded in an Aspen HYSYS or Aspen Plus simulation, you have a much
more effective tool to study how an exchanger and the overall process will react to seasonal
variations.
18. Is there a separate package to the HTRI program that is already supplied by AspenTech?
AspenTech does not supply HTRI software products; HTRI is a competitor.
19. What are the major differences between EDR and HTRI? How does the thermal design
compare with HTRI models?
AspenTech is unable to make direct comparisons of our offering to HTRIs; however, there are many
benefits to using Aspen EDR. The webinar associated with this Q&A document focuses on several
of these benefits, including:
Integration with Simulation: Aspen EDR models can be embedded in flowsheets from
Aspen Plus & Aspen HYSYS—industry leading process simulators for both Chemicals,
Oil, and Gas applications—improving flowsheets for revamp studies, troubleshooting
operations, and debottlenecking processes. See the Petrofac Case Study for an example
of how a customer benefitted from rigorous Aspen EDR models in Aspen HYSYS.
Physical Properties: Aspen EDR can import properties from Aspen Plus & Aspen
HYSYS cases (as shown in the webinar) or properties can be specified using one of the
included databanks: BJAC, Aspen Properties, or COMThermo. The integration and the
breadth of the property databanks significantly reduce the time required to input process
data.
Thermal Modeling: EDR thermal modeling is based on our HTFS research heritage from
the late 1960s and continues with our current programs. This provides state of the art
correlations and methods documented in the Aspen HTFS Research Network. The
Research Network is licensed by many of our leading customers. We are regularly
involved in analyzing comparisons between our results and those of other software
suppliers. When called upon, we are always happy to demonstrate the validity of our
methods with reference to sound theory and extensive validation data covering a wide
range of exchanger configurations and process conditions.
Thermal Design Optimization: Aspen Shell & Tube typically evaluates hundreds of
exchanger configurations—considering the number of shells required, as well as details
of shell geometry. The optimum design is selected on a rigorous algorithm for cost of
labor and materials of construction. Similar optimization capabilities are also available in
the Aspen Air Cooled Exchanger program.
Mechanical Design Optimization: Aspen Shell & Tube Mechanical is the only pressure
vessel design product on the market that was developed exclusively for heat exchangers.
Drawing on the long heritage of the B-JAC Teams program, Aspen Shell & Tube
Mechanical provides powerful, optimized mechanical design that recognizes the
interaction of key components. The designs produced minimize material thicknesses and
reduce costs while still maintaining design integrity and conforming to internationally
accepted code standards.
Thermal & Mechanical Integration: The integration between the thermal software and
the mechanical software significantly reduces the time to hand off designs between
thermal designers and mechanical engineers.
If you’re interested in learning more about how Aspen EDR can benefit your business, please
contact your Sales Account Manager or visit www.aspentech.com/products/aspen-edr.aspx.
Input/UI
1. When rating an existing exchanger, how do you change the way baffle cut is specified
(% area vs. % diameter)?
In the EDR Shell & Tube program, the baffle cut is expressed as a percentage of the shell inside the
diameter. You will need to use a manual calculation from the figures expressed in the percent shell
side net free area (taking account of the area occupied by the tubes) to convert to a % shell diameter
basis.
2. Where does EDR put in supports (I'm talking about the extra supports option)?
If you specify additional supports between tubes in window baffles, these are equally spaced between
baffles. They will appear illustrated on the setting plan. Similarly, additional supports in inlet and
outlet regions will be equally spaced between the first baffle and the tube sheet.
3. How do you export heat exchanger process conditions from Aspen Plus to EDR?
On a HYSYS Exchanger, go to Design > Parameters and select Rigorous Shell & Tube as your
Exchanger Model. Then, go to the Rigorous Shell & Tube tab and click the Export button, which will
then open a file. Save the file, choose a folder location, and name it as “.EDR”.
4. How can you have two outlet streams (flashed vapor and liquid) on one side of a Heat
Exchanger?
In Shell & Tube under Input > Exchanger Geometry > Nozzles you can select the option to have a
separate liquid and vapor nozzle. You may also specify dimensions or have the program size these
for you.
5. How can I send the calculated geometry back to Aspen HYSYS and/or Aspen Plus to be used
in the simulation?
When you have an EDR model, you can import it into a HYSYS Exchanger. Go to Design >
Parameters and select Rigorous Shell & Tube as your Exchanger Model. Then, go to the Rigorous
Shell & Tube tab and click the Import button. A file will appear. Open the dialogue box which allows
you to browse a folder location where you select your case file “.EDR”.
6. Where can I find the internal volume of a heat exchanger, Shell and Tube side, to calculate the
necessary mass of the fluid?
The Shell and Tube Mechanical program outputs the shell side or tube side volumes, as well as the
Operating Weight (with the process fluids present). See Figure 3 below.
8. Can you describe the manual input for stream properties without using the HYSYS property
input?
If you refer to the Aspen Support Knowledge Base, Solution number 137332: Learn how to specify
properties for Aspen Exchanger Design & Rating (EDR) family of products for process heat
exchanger modeling, it shows how to manually specify properties for single phase, two-phase, and
Vapor Liquid-Liquid systems. You will also find tutorials on using the physical property packages
included in Shell & Tube and the other Aspen EDR products.
Calculation Results
1. Can you obtain a results report with the thermal and mechanical design combined?
Currently, our Shell & Tube Thermal and Mechanical programs produce individual reports which you
may tailor to your needs.
3. Before we begin, does it apply to both Division 1 & 2 of the ASME code?
The mechanical calculations apply to ASME Division 1. ASME is progressively bringing together
mechanical calculations so that more advanced Division 2 methods can be added to our program with
each release.
4. In X shell design, what is the accuracy level in the mechanical design when shell side nozzles
are more than 2?
Generally, there shouldn’t be problems with the mechanical aspects of multi-nozzle X-shell designs
unless the nozzles are in very close proximity. Please contact AspenTech Support if you have a case
you would like us to look at.
5. Do multi-nozzle X-shell designs consider heat loss, based on the environment, to insulation
thickness?
No, it is assumed that exchangers are well insulated.
6. How does Aspen EDR calculate the mixed oil and water viscosities?
In our research program, we have recently looked closely at modeling in this area and provided new
recommendations on handling the modeling of streams with two liquid phases. If you provide
property data for two liquid phases, the program will default to the new HTFS Method handling
condensation somewhat differently from heating or cooling with no phase change. You may also
over-ride the program selection under Input > Program Options > Methods/Correlations > General
and select your preferred method for viscosity of two liquid phases. You can also look on our support
site at the Aspen Support Knowledge Base Solution 133770 White Paper - Heat Exchanger Methods
for Effective Viscosities of Two Immiscible Liquid Phases.
7. EDR does not consider high pressure when calculating baffle thickness and number of
baffles. Why can’t you fit the same number as calculated in EDR design?
Generally, there shouldn’t be an issue with high pressure units in terms of number of baffles. What
might be more important here is the thickness of the tube sheets, positioning of nozzles, and the
interaction of these with the baffle spacing. Please contact AspenTech Support if you have a case
you would like us to look at.