Professional Documents
Culture Documents
Adjustments are made by going to “Operations > Space and Depth Adjustment” and the typing 1, 2 or 3 for Jaws 1, 2 and
3 and clicking OK.
To measure the
spacing on a tip stop
key like the high To measure a depth on
security Honda key set a high security Honda
a caliper to the space key, find the space for
that you want to the depth you want to
measure using the measure and measure
space data on the edit from the edge of the key
page and the measure to the edge of the cut.
from the tip toward Compare the reading
the bow. For a against the Cut Depth
shoulder stop key, info on the edit page.
measure from
shoulder to tip.
Now trace either a blank or OEM cut high security Honda key. It’s best not to use an
aftermarket key because it may not be cut to spec. In this example we are tracing an
[Trace Reading Example]
OEM cut key.
At the bottom right hand corner of your 3D Pro software is a text box, and at the (1,3);283
bottom of this box are the readings for the trace, one line per cut. The readings show (2,5);253
the space, cut and tracer measurement. The readings are shown in the order in which (3,5);253
they have been traced. (4,4);268
A blank will read all zeros measuring 352 all the way down the key.
(5,5);253
(6,1);308
An OEM key should always read ones in both 6th spaces measuring 311.
The 6th spaces will show in the middle of the readings list and we see in the example (6,1);313
that the key profile is off to the left by 3 thousandths of an inch. The trace reading (5,5);256
shows that the 6th space on side A measured to 308 thousandths of an inch when it is (4,1);312
supposed to be 311 thousandths of an inch. This in turn causes the 6th space on side B (3,5);256
to be off as well. To correct this we will make a space and depth adjustment to move (2,6);242
the cut profile to the right by 3 thousandths of an inch. This will make the 6th space on (1,4);269
side A measure 311 and the 6th space on side B measure 310.
To make this adjustment go to “Operations > Space and Depth Adjustment” type “1” and press “OK”
You will see the window shown above. Type “3” under “Tracer” next to “Depth Offset:” and then press “Update”
Page 4 of 7
Adjusting space and depth for the Jaw 1 cutting is the same
as adjusting Jaw 1 Tracer accept that you will have to cut a
key, measure it, and make the adjustment. Cut a high
security to a random code or all ones and measure as
shown below. The tip of this high security Honda key will
have ones on both 6 space cuts (or along the whole key if
you cut to all ones) and should measure to 311.
Shown to the right is an example of how to measure a cut
high security Honda key at the 6th space on side A.
If the 6th space on side A measures less than 311 the make a
positive adjustment to move the keys profile to the right if
the measurement is more than 311 than make a negative
adjustment to move the key profile to the left.
Making adjustments affects all cuts.
Let us say that 6th space on side A is measuring to 314 then
the adjustment will be made as shown below.
To make this adjustment go to “Operations > Space and Depth Adjustment” type “1” and press “OK”
You will see the window shown above. Type “-3” under “Cutter” next to “Depth Offset:” and then press “Update”
Repeat the same process for spacing.
Page 5 of 7
Below is a visual
representation of the DSD.
Cut a Schlage key to all ones and measure the depth with calipers. According the edit page for the Schlage key, one
depths should measure to 320 thousandths of an inch. If your key measures too shallow, say 325 then make a negative
adjustment to the cutter depth offset. If your key measures too deep, say 315 then make a plus adjustment to the cutter
depth offset. Negative adjustments are made by putting a minus sign in front of the number used in the adjustment box.
To adjust the spacing, cut a Schlage key to all ones with a 3 in the third space set your calipers to .543 inches and
measure from the shoulder to the tip and see if the 3 cut meets the measurement. If the 3 cut is too far toward the
shoulder of the key then enter a negative number in the Depth Offset under CUTTER. If the 3 cut is too far toward the tip
of the key then enter a positive number in the Depth
Page 7 of 7
Optional Accessories
Bolt Down Kit Lexus 80000 Code Series Cutter Tibbe Adapter
Laptop Mount
LaserKeyProducts.com